INTEGRATED CIRCUITS DATA SHEET TEA6846H New In Car Entertainment (NICE) car radio Product specification Supersedes data of 2001 Apr 12 2003 Feb 04 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H CONTENTS 1 FEATURES 2 GENERAL DESCRIPTION 3 QUICK REFERENCE DATA 4 ORDERING INFORMATION 5 BLOCK DIAGRAM 6 PINNING 7 FUNCTIONAL DESCRIPTION 7.1 7.1.1 7.1.2 7.1.3 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.3.6 7.4 Oscillators VCO Crystal oscillator PLL FM signal channel DAA FM I/Q mixer FM keyed AGC FM IF amplifiers FM demodulator AM signal channel AM tuner including mixer 1 and mixer 2 AM RF AGC and IF2 AGC AM detector AM AF or IF2 switch AM noise detector and blanker FM and AM level detector Test mode 8 11 AC CHARACTERISTICS 12 I2C-BUS PROTOCOL 12.1 12.1.1 12.1.2 12.1.3 12.1.4 12.2 12.2.1 12.2.2 12.2.3 12.2.4 12.2.5 12.2.6 12.2.7 12.2.8 I2C-bus specification Test mode Data transfer I2C-bus pull-up resistors Frequency setting I2C-bus protocol Data transfer mode and IC address Write mode: data byte 1 Write mode: data byte 2 Write mode: data byte 3 Write mode: data byte 4 Write mode: data byte 5 Write mode: data byte 6 Read mode: data byte 1 13 TEST AND APPLICATION INFORMATION 14 PACKAGE OUTLINE 15 SOLDERING 15.1 Introduction to soldering surface mount packages Reflow soldering Wave soldering Manual soldering Suitability of surface mount IC packages for wave and reflow soldering methods 15.2 15.3 15.4 15.5 16 DATA SHEET STATUS LIMITING VALUES 17 DEFINITIONS 9 THERMAL CHARACTERISTICS 18 DISCLAIMERS 10 DC CHARACTERISTICS 19 PURCHASE OF PHILIPS I2C COMPONENTS 2003 Feb 04 2 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 1 TEA6846H FEATURES * FM mixer for conversion of FM RF from 65 to 108 MHz to IF of 10.7 MHz; the mixer provides inherent image rejection * FM RF mixer can be set to receive weather band radio up to 162.55 MHz; weather band radio flag output * Level detector for AM and FM with temperature compensated output voltage; starting point and slope of level output is programmable via the I2C-bus * AM mixer 1 for conversion of AM RF to AM IF1 of 10.7 MHz * LC tuner oscillator providing mixer frequencies for FM mixer and AM mixer 1 * AM RF PIN diode drive circuit; AGC threshold detection at AM mixer 1 and IF2 AGC input; threshold is programmable via the I2C-bus; AM IF2 AGC and demodulator * AM mixer 2 for conversion of AM IF1 to AM IF2 of 450 kHz * AM AF output switchable to provide AM IF2 for AM stereo decoder * Crystal oscillator providing mixer frequencies for AM mixer 2 and reference for synthesizer PLL, IF count, timing for Radio Data System (RDS) update and reference frequency for car audio signal processor ICs * AM noise blanker with blanking at AM IF2 * Several test modes available for fast IC and system tests. * Fast synthesizer PLL tuning system with local control for inaudible RDS updating * Timing function for RDS update algorithm and control signal output for car audio signal processor ICs (TEA688x, SAA77xx or TEF689x) 2 GENERAL DESCRIPTION The TEA6846H is a single IC with car radio tuner for AM and FM intended for microcontroller tuning with the I2C-bus. It provides the following functions: * Digital auto alignment circuit for conversion of LC oscillator tuning voltage to controlled alignment voltage of FM antenna tank circuit * AM double conversion receiver for LW, MW and SW (31 m, 41 m and 49 m bands) with IF1 = 10.7 MHz and IF2 = 450 kHz * AGC PIN diode drive circuit for FM RF AGC; AGC detection at FM mixer input; the AGC PIN diode drive can be activated by the I2C-bus as a local or distance function; AGC threshold is a programmable and keyed function switchable via the I2C-bus * FM single conversion receiver with integrated image rejection for IF = 10.7 MHz capable of selecting US FM, US weather, Europe FM, East Europe FM and Japan FM bands. * FM IF linear amplifiers with high dynamic input range * FM quadrature demodulator with automatic centre frequency adjustment and Total Harmonic Distortion (THD) compensation 3 ORDERING INFORMATION TYPE NUMBER TEA6846H 2003 Feb 04 PACKAGE NAME LQFP80 DESCRIPTION plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm 3 VERSION SOT315-1 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 4 TEA6846H QUICK REFERENCE DATA SYMBOL PARAMETER VDDA(n) analog supply voltage 1, 3, 4, 5 and 6 IDDA(tot) total analog supply current 1, 3, 4, 5 and 6 VDDA2 analog supply voltage 2 IDDA2 analog supply current 2 VDDD digital supply voltage IDDD digital supply current fAM(ant) AM input frequency CONDITIONS MIN. TYP. MAX. UNIT 8 8.5 9 V FM mode 45 56 67 mA AM mode 39 49 59 mA 4.75 5 5.25 V FM mode 6.5 8.1 9.8 mA AM mode 4.7 5.9 7.1 mA 4.75 5 5.25 V FM mode 18 23 28 mA AM mode 18 23 28 mA LW 0.144 - 0.288 MHz MW 0.522 - 1.710 MHz SW 5.85 - 9.99 MHz fFM(ant) FM input frequency 65 - 108 MHz fFM(WB)(ant) FM weather band input frequency 162.4 - 162.55 MHz Tamb ambient temperature -40 - +85 C AM overall system parameters (1 x SFE10.7MS3; 1 x SFR450H) (S+N)/N signal plus noise-to-noise ratio m = 0.3 - 58 - dB THD total harmonic distortion m = 0.8 - 0.3 - % m = 0.9 - 0.5 - % FM overall system parameters (3 x SFE10.7MS3) (S+N)/N signal plus noise-to-noise ratio f = 22.5 kHz; de-emphasis = 50 s - 65 - dB THD total harmonic distortion f = 75 kHz - 0.6 1 % 2003 Feb 04 4 This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... DAAOUT 44 45 46 AFHOLD 47 48 49 AFSAMPLE 51 50 53 39 38 54 55 SEQUENTIAL CIRCUIT FOR RDS UPDATING VCO ANTENNA DAA AMAFIF2 TRDSMUTE RDSMPX FMMPX 56 57 AM DETECTOR VDDA2 VDDA1 58 59 61 POWER SUPPLY MUTE TUNING SYSTEM AM 2 ms/20 ms 10.25 MHz I2C-bus T1FMAGC T2FMAGC IFMAGC AM IF2 37 36 35 63 FM IF IF COUNT I2C-BUS SCL FM AGC 66 RFGND FMMIXIN1 67 33 x 31 FM I/Q MIXER 30 AM IF AGC N1 /2 90 LEVEL DAA 68 5 29 AM-NOISE DETECTOR 90 PEAK/ AVERAGE 70 71 T2AMAGC T1AMAGC AMMIX1IN1 28 27 26 x N2 / 5/10 AM RF AGC FM LIMITER/ LEVEL AM MIXER2 CRYSTAL OSCILLATOR 72 73 76 23 x IFAMP1 77 78 20 19 18 17 16 14 12 MIX1OUT2 VDDA5 IFAMP1DEC MIX1OUT1 IFAMP1IN VDDA6 XTAL1 XTALGND XTAL2 IREF 9 Coffset 8 7 6 5 4 3 2 1 IFAMP1OUT IFAMP2DEC IF1GND IFAMP2IN Fig.1 Block diagram. FMLIMIN AMIF2IN AMIF2DEC AMNBHOLD IFAMP2OUT AMMIX2OUT1 AMMIX2OUT2 79 CAGC FMLIMDEC TEA6846H 11 MGU351 AMMIX1IN2 Vlevel Product specification 22 CAFC IFAMP2 AM MIXER 1 handbook, full pagewidth IAMAGC QDET2 AM LEVEL BLANK PULSE QDET1 DEMODULATOR 69 Vref(FMMIX) IF2GND WX TEA6846H FMMIXIN2 SDA 64 New In Car Entertainment (NICE) car radio DAATD 43 VDDA3 OSCFDB VCOGND OSCTNK BLOCK DIAGRAM 42 40 VDDA4 FREF VDDD Philips Semiconductors 5 2003 Feb 04 DGND Vtune CPOUT DAAIN Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 6 TEA6846H PINNING SYMBOL PIN DESCRIPTION FMLIMDEC 1 FM limiter decoupling FMLIMIN 2 FM limiter input (10.7 MHz) AMIF2DEC 3 decoupling for AM IF2 input IFAMP2OUT 4 IF amplifier 2 output (10.7 MHz) AMNBHOLD 5 AM noise blanker threshold AMIF2IN 6 AM IF2 input (450 kHz) for demodulator AGC and AM level detector IF1GND 7 AM IF1 ground IFAMP2IN 8 IF amplifier 2 input (10.7 MHz) Coffset 9 DC feedback for offset compensation RDS mute n.c. 10 not connected IFAMP2DEC 11 IF amplifier 2 decoupling and AGC capacitor for AM noise blanker IFAMP1OUT 12 IF amplifier 1 output (10.7 MHz) n.c. 13 not connected IFAMP1IN 14 IF amplifier 1 and AM mixer 2 input (10.7 MHz) n.c. 15 not connected VDDA6 16 analog supply voltage 6 (8.5 V) for IF amplifier 1 and 2 IFAMP1DEC 17 AM mixer 2 and FM IF amplifier 1 decoupling MIX1OUT1 18 FM mixer and AM mixer 1 IF output 1 (10.7 MHz) MIX1OUT2 19 FM mixer and AM mixer 1 IF output 2 (10.7 MHz) VDDA5 20 analog supply voltage 5 (8.5 V) for FM mixer and AM mixer 1 n.c. 21 not connected AMMIX1IN2 22 AM mixer 1 input 2 AMMIX1IN1 23 AM mixer 1 input 1 n.c. 24 not connected n.c. 25 not connected T1AMAGC 26 1st time constant of AM front-end AGC T2AMAGC 27 2nd time constant of AM front-end AGC IAMAGC 28 PIN diode drive current output of AM front-end AGC Vref(FMMIX) 29 reference voltage for FM I/Q mixer FMMIXIN1 30 FM RF mixer input 1 RFGND 31 RF ground n.c. 32 not connected FMMIXIN2 33 FM RF mixer input 2 n.c. 34 not connected IFMAGC 35 PIN diode drive current output of FM front-end AGC T2FMAGC 36 2nd time constant of FM front-end AGC T1FMAGC 37 1st time constant of FM front-end AGC DAAOUT 38 output of digital auto alignment circuit for antenna tank circuit DAATD 39 temperature compensation diode for digital auto alignment circuit for antenna tank circuit DAAIN 40 input of digital auto alignment circuit for antenna tank circuit 2003 Feb 04 6 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL TEA6846H PIN DESCRIPTION n.c. 41 not connected Vtune 42 tuning voltage CPOUT 43 charge pump output VDDA4 44 analog supply voltage 4 (8.5 V) for tuning PLL FREF 45 reference frequency output for signal processor IC VDDD 46 digital supply voltage (5 V) DGND 47 digital ground VCOGND 48 VCO ground OSCFDB 49 VCO feedback OSCTNK 50 VCO tank circuit VDDA3 51 analog supply voltage 3 (8.5 V) for VCO n.c. 52 not connected AFSAMPLE 53 AF sample flag output for car audio signal processor IC AFHOLD 54 AF hold flag output for car audio signal processor IC TRDSMUTE 55 time constant for RDS update mute AMAFIF2 56 AM demodulator AF output or IF2 output for AM stereo (multiplexed by I2C-bus) RDSMPX 57 MPX output for RDS decoder and signal processor (not muted) FMMPX 58 FM demodulator MPX output VDDA2 59 analog supply voltage 2 (5 V) for on-chip power supply n.c. 60 not connected VDDA1 61 analog supply voltage 1 (8.5 V) for on-chip power supply n.c. 62 not connected SDA 63 I2C-bus data line input and output SCL 64 I2C-bus clock line input n.c. 65 not connected IF2GND 66 AM IF2 ground QDET1 67 quadrature demodulator tank 1 QDET2 68 quadrature demodulator tank 2 CAFC 69 FM demodulator AFC capacitor Vlevel 70 level voltage output for AM and FM XTAL1 71 crystal oscillator 1 XTALGND 72 crystal oscillator ground XTAL2 73 crystal oscillator 2 n.c. 74 not connected n.c. 75 not connected IREF 76 reference current for power supply AMMIX2OUT1 77 AM mixer 2 output 1 (450 kHz) AMMIX2OUT2 78 AM mixer 2 output 2 (450 kHz) CAGC 79 AM IF AGC capacitor n.c. 80 not connected 2003 Feb 04 7 Philips Semiconductors Product specification 61 VDDA1 62 n.c. 63 SDA 64 SCL 65 n.c. 66 IF2GND 67 QDET1 68 QDET2 70 Vlevel 71 XTAL1 69 CAFC TEA6846H 72 XTALGND 73 XTAL2 74 n.c. 75 n.c. 76 IREF 77 AMMIX2OUT1 79 CAGC 80 n.c. handbook, full pagewidth 78 AMMIX2OUT2 New In Car Entertainment (NICE) car radio FMLIMDEC 1 60 n.c. FMLIMIN 2 59 VDDA2 AMIF2DEC 3 58 FMMPX IFAMP2OUT 4 57 RDSMPX AMNBHOLD 5 56 AMAFIF2 AMIF2IN 6 55 TRDSMUTE IF1GND 7 54 AFHOLD IFAMP2IN 8 53 AFSAMPLE Coffset 9 52 n.c. 51 VDDA3 n.c. 10 TEA6846H IFAMP2DEC 11 50 OSCTNK IFAMP1OUT 12 49 OSCFDB n.c. 13 48 VCOGND IFAMP1IN 14 47 DGND n.c. 15 46 VDDD VDDA6 16 45 FREF IFAMP1DEC 17 44 VDDA4 MIX1OUT1 18 43 CPOUT MIX1OUT2 19 42 Vtune VDDA5 20 Fig.2 Pin configuration. 2003 Feb 04 8 DAAIN 40 DAATD 39 DAAOUT 38 T1FMAGC 37 T2FMAGC 36 IFMAGC 35 n.c. 34 FMMIXIN2 33 n.c. 32 RFGND 31 FMMIXIN1 30 Vref(FMMIX) 29 IAMAGC 28 T2AMAGC 27 T1AMAGC 26 n.c. 25 n.c. 24 AMMIX1IN1 23 AMMIX1IN2 22 n.c. 21 41 n.c. MHB882 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 7 TEA6846H It includes an AGC PIN diode drive circuit for the FM RF AGC. The PIN diode drive can be activated via the I2C-bus as a local or distance function. FUNCTIONAL DESCRIPTION 7.1 7.1.1 Oscillators VCO The AGC threshold is programmable and the keyed AGC function is switchable via the I2C-bus. The L and C tuned VCO provides the local oscillator signal for both FM and AM mixer 1. It has a frequency range of 151.2 to 248.2 MHz. 7.1.2 7.2.4 The two FM IF amplifiers provide 10 dB and 4 dB amplification with high linearity and dynamic range. CRYSTAL OSCILLATOR The crystal oscillator provides a 20.5 MHz signal that is used for: 7.2.5 * Reference frequency for frequency synthesizer PLL FM DEMODULATOR The FM quadrature demodulator includes automatic centre frequency adjustment and THD compensation. * Local oscillator for AM mixer 2 * Reference frequency for the IF counter 7.3 * Timing signal for the RDS update algorithm 7.3.1 * Reference frequency (75.4 kHz) for the TEA688x (car audio signal processor - CASP) or TEF689x (car radio integrated signal processor - CRISP). 7.1.3 FM IF AMPLIFIERS AM signal channel AM TUNER INCLUDING MIXER 1 AND MIXER 2 The AM tuner is realized in a double conversion technique and is capable of selecting LW, MW and SW bands. AM mixer 1 converts AM RF to IF1 of 10.7 MHz, while AM mixer 2 converts IF1 of 10.7 MHz to IF2 of 450 kHz: PLL Fast synthesizer PLL tuning system with local control for inaudible RDS updating. * LW = 144 to 288 kHz 7.2 * SW = 5.85 to 9.99 MHz (including the 31 m, 41 m and 49 m bands). 7.2.1 * MW = 530 to 1710 kHz (US AM band) FM signal channel DAA 7.3.2 FM RF Digital Auto Alignment (DAA) circuitry for the conversion of the VCO tuning voltage to a controlled alignment voltage for the FM antenna tank circuit. 7.2.2 AM RF AGC AND IF2 AGC The AM RF includes a PIN diode drive circuit. The threshold detection points for AM AGC are performed at AM mixer 1 and AM IF2. AGC thresholds are programmable via the I2C-bus. FM I/Q MIXER FM quadrature mixer converts FM RF (65 to 162.55 MHz) to IF of 10.7 MHz. The FM mixer provides inherent image rejection and high RF sensitivity. 7.3.3 AM DETECTOR The AM detector provides AM level information and AM AF or AM IF2. It is capable of tuning the US FM, US weather, Europe FM, Japan FM and East Europe FM bands: AM AF OR IF2 SWITCH * US FM = 87.9 to 107.9 MHz 7.3.4 * US weather FM = 162.4 to 162.55 MHz The AM output provides either a detected AM AF or the corresponding AM IF2 signal. The IF2 signal can be used for AM stereo decoder processing. * Europe FM = 87.5 to 108 MHz * Japan FM = 76.0 to 91 MHz * East Europe FM = 65.8 to 74 MHz. 7.2.3 FM KEYED AGC FM contains keyed wide-band RF AGC. AGC detection occurs at the FM mixer. The wide-band RF signal switches a narrow band signal (IF) from the FM IF level detector circuitry that controls the FM RF AGC block. 2003 Feb 04 9 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 7.3.5 TEA6846H AM NOISE DETECTOR AND BLANKER If the test mode is enabled by pin FREF: * The settling time of the AM IF2 AGC is reduced to less than 100 ms in the nominal application The detection point for the AM noise blanker is the output stage of AM mixer 1, while blanking is realized at the output of the mixer 2. * The digital-to-analog converters for the antenna DAA and the level DAA can be clocked directly by the SCL line of the I2C-bus Trigger sensitivity can be modified by changing the resistor value at pin AMNBHOLD. 7.3.6 * The output at pin FREF can be selected by the I2C-bus: TEA688x or TEF689x reference frequency, PLL reference frequency or PLL programmable divider output frequency FM AND AM LEVEL DETECTOR FM and AM level detectors provide the temperature compensated output voltage. The starting points and slopes of the level detector outputs are programmable via the I2C-bus. * The RDS update control circuit can be clocked directly via pin DAATD 7.4 * Pin T1AMAGC can be used to enable the load PLL circuit of the RDS update control circuit Test mode * Charge pumps can be set into 3-state mode. The test mode of the IC is activated by: * Sending the test byte (byte 5) to the IC * Connecting pin FREF through a 100 k resistor to VDDA1 * Applying 50 A to pin FREF. 8 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VDDA1 analog supply voltage 1 for on-chip power supply -0.3 +10 V VDDA2 analog supply voltage 2 for on-chip power supply -0.3 +6.5 V VDDA3 analog supply voltage 3 for VCO -0.3 +10 V VDDA4 analog supply voltage 4 for tuning PLL -0.3 +10 V VDDA5 analog supply voltage 5 for FM and AM RF -0.3 +10 V VDDA6 analog supply voltage 6 for IF amplifier 1 and 2 -0.3 +10 V VDDD digital supply voltage -0.3 +6.5 V -0.3 - V -55 +150 C VDD8.5-DD5 difference between any 8.5 V supply voltage and any 5 V supply voltage Tstg storage temperature Tamb ambient temperature Ves electrostatic handling voltage note 1 -40 +85 C note 2 -200 +200 V note 3 -2000 +2000 V Notes 1. To avoid damages and wrong operation it is necessary to keep all 8.5 V supply voltages at a higher level than any 5 V supply voltage. This is also necessary during power-on and power-down sequences. Precautions have to be provided in such a way that interferences can not pull down the 8.5 V supply below the 5 V supply. 2. Machine model (R = 0 , C = 200 pF). 3. Human body model (R = 1.5 k, C = 100 pF). 2003 Feb 04 10 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 9 TEA6846H THERMAL CHARACTERISTICS SYMBOL Rth(j-a) PARAMETER thermal resistance from junction to ambient CONDITIONS VALUE UNIT 54 K/W in free air 10 DC CHARACTERISTICS VDDA1 = VDDA3 = VDDA4 = VDDA5 = VDDA6 = 8.5 V; VDDA2 = 5 V; VDDD = 5 V; Tamb = 25 C; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply voltage VDDA(n) analog supply voltage 1, 3, 4, 5 and 6 8 8.5 9 V VDDA2 analog supply voltage 2 4.75 5 5.25 V VDDD digital supply voltage 4.75 5 5.25 V Supply current in FM mode IDDD digital supply current 18 23 28 mA IDDA1 analog supply current 1 for on-chip power supply - 15 - mA IDDA2 analog supply current 2 for on-chip power supply 6.5 8.1 9.8 mA IDDA3 analog supply current 3 for VCO - 6.5 - mA IDDA4 analog supply current 4 for tuning PLL - 2.9 - mA IDDA5 analog supply current 5 for FM RF - 5 - mA IDDA6 analog supply current 6 for FM IF amplifier 1 and 2 10 12 14 mA IMIX1OUT1 bias current of FM mixer output 1 4.8 6 7.2 mA IMIX1OUT2 bias current of FM mixer output 2 4.8 6 7.2 mA test mode; bit TMS3 = 1 Supply current in AM mode IDDD digital supply current 18 23 28 mA IDDA1 analog supply current 1 for on-chip power supply - 17.5 - mA IDDA2 analog supply current 2 for on-chip power supply 4.7 5.9 7.1 mA IDDA3 analog supply current 3 for VCO - 6.5 - mA IDDA4 analog supply current 4 for tuning PLL - 1.6 - mA IDDA5 analog supply current 5 for RF - 1.8 - mA IMIX1OUT1 bias current of AM mixer 1 output 1 4.8 6 7.2 mA IMIX1OUT2 bias current of AM mixer 1 output 2 4.8 6 7.2 mA IAMMIX2OUT1 bias current of AM mixer 2 output 1 3.6 4.5 5.4 mA IAMMIX2OUT2 bias current of AM mixer 2 output 2 3.6 4.5 5.4 mA 2003 Feb 04 test mode; bit TMS3 = 1 11 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL TEA6846H PARAMETER CONDITIONS MIN. TYP. MAX. UNIT On-chip power supply reference current generator: pin IREF Vo(ref) output reference voltage 4 4.25 4.5 V Ro output resistance 8 11 13 k Io(max) maximum output current -100 - +100 nA 11 AC CHARACTERISTICS VDDA1 = VDDA3 = VDDA4 = VDDA5 = VDDA6 = 8.5 V; VDDA2 = 5 V; VDDD = 5 V; Tamb = 25 C; see Figs 9 and 10; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Voltage controlled oscillator 151.2 - 248.2 - 101 - fosc = 250 MHz - 97 - dB fosc = 200 MHz - 99 - dB 2.2 2.8 3.4 V 5 6.1 7.2 V fosc = 200 MHz - 1.5 - V 20.4996 20.5 20.5004 MHz start of operating - - 500 - - 18 pF - 112 - - 350 - mV 1.7 2.1 2.5 V fosc oscillator frequency C/N carrier-to-noise ratio fosc = 200 MHz; f = 10 kHz RR ripple rejection fripple = 100 Hz; VDDA3(ripple) = 100 mV (RMS) MHz dBc -----------Hz FEEDBACK INPUT: PIN OSCFDB Vi(bias) input bias voltage TANK CIRCUIT OUTPUT: PIN OSCTNK VO DC output voltage Vo(rms) AC output voltage (RMS value) Crystal oscillator fxtal crystal frequency Rxtal crystal motional resistance Cxtal crystal shunt capacitance C/N carrier-to-noise ratio fxtal = 20.5 MHz (10.25 MHz); f = 10 kHz dBc -----------Hz CIRCUIT INPUTS: PINS XTAL1, XTAL2 AND XTALGND Vxtal(rms) crystal voltage (RMS value) VXTAL1, VXTAL2 DC bias voltage Ri real part of input impedance VXTAL1 - VXTAL2 = 1 mV; note 1 -500 - - Ci input capacitance note 1 8 10 12 pF 2003 Feb 04 note 1 12 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL IXTALGND PARAMETER crystal oscillator circuit current TEA6846H CONDITIONS MIN. TYP. MAX. UNIT start-up at VXTAL1 = VXTAL2 = 2.1 V - 9 - mA operating at VXTAL1 - VXTAL2 = 400 mV - 1.5 - mA standard, Europe and local - 2 - weather band (WX) - 1 - LW and MW - 10 - SW - 5 - Oscillator divider N1 N1 oscillator divider ratio FM mode Oscillator divider N2 N2 oscillator divider ratio AM mode Synthesizer PROGRAMMABLE DIVIDER Nprog programmable divider ratio 512 - 32767 Nstep programmable divider step size - 1 - fref = 100 kHz - 205 - fref = 50 kHz - 410 - fref = 25 kHz - 820 - fref = 20 kHz - 1025 - fref = 10 kHz - 2050 - REFERENCE FREQUENCY DIVIDER Nref crystal oscillator divider ratio fxtal = 20.5 MHz CHARGE PUMP: PIN CPOUT Isink(cp1)l low charge pump 1 peak sink current FM weather band mode; 0.4 V < VCPOUT < 7.6 V 200 300 400 A Isource(cp1)l low charge pump 1 peak source current FM weather band mode; 0.4 V < VCPOUT < 7.6 V -400 -300 -200 A Isink(cp1)h high charge pump 1 peak sink current AM stereo mode; N2 = 10 (LW and MW); 0.4 V < VCPOUT < 7.6 V 0.7 1 1.3 mA Isource(cp1)h high charge pump 1 peak source current AM stereo mode; N2 = 10 (LW and MW); 0.4 V < VCPOUT < 7.6 V -1.3 -1 -0.7 mA Isink(cp2) charge pump 2 peak sink current FM standard mode; 0.3 V < VCPOUT < 7.1 V 100 130 160 A Isource(cp2) charge pump 2 peak source current FM standard mode; 0.3 V < VCPOUT < 7.1 V -160 -130 -100 A 0 < VCPOUT < 8.5 V -5 - +5 nA IZ(cp1), IZ(cp2) charge pump 1 or 2 current in 3-state 2003 Feb 04 13 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT CHARGE PUMP: PIN Vtune Isink(cp3) charge pump 3 peak sink current FM standard mode; 0.4 V < Vtune < 7.6 V 2.1 3 3.9 mA Isource(cp3) charge pump 3 peak source current FM standard mode; 0.4 V < Vtune < 7.6 V -3.9 -3 -2.1 mA IZ(cp3) charge pump 3 current in 3-state 0 < Vtune < 8.5 V -5 - +5 nA FM mode; 0.4 V < VDAAIN < 8.0 V -10 - +10 nA AM mode; 0 V < VDAAIN < 8.5 V -10 - +10 nA 0 - 8.5 V - - 0.3 V - - 0.5 V Antenna Digital Auto Alignment (DAA) DAA INPUT: PIN DAAIN Ibias(cp) Vi(cp) charge pump buffer input bias current charge pump buffer input voltage DAA OUTPUT: PIN DAAOUT; note 2 Vo(AM) DAA output voltage in AM mode Vo(FM) DAA output voltage in FM mode VDAAIN = 4.0 V; VDAATD = 0.7 V minimum value bits DAA[6:0] set to logic 0 1.5 1.65 1.8 V value: data byte 3 = 10101011 3.8 4 4.2 V maximum value; bits DAA[6:0] set to logic 1 8 - 8.5 V 6.2 6.5 6.8 V 3 3.3 3.6 V VDAAIN = 3.0 V; VDAATD = 0.7 V; bits DAA[6:0] set to logic 1 VDAAIN = 2 V data byte 3 = 11010101 1.8 2 2.2 V Vo(n) DAA output noise voltage FM mode; VDAAIN = 4 V; data byte 3: bit 6 = 1, bits 5 to 0 = 0; B = 300 Hz to 15 kHz data byte 3 = 10101010 - 30 100 V Vo(T) DAA output voltage variation with temperature Tamb = -40 to +85 C; data byte 3 = 10101011; VDAATD = 0.7 V -8 - +8 mV Vo(step) DAA step accuracy FM mode; VDAAOUT < 8.0 V; n = 0 to 127 0.5VLSB VLSB 1.5VLSB mV Io(sink) DAA output sink current 0.2 V < VDAAOUT < 8.25 V 50 - - A Io(source) DAA output source current - - -50 A 2003 Feb 04 14 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL tst PARAMETER DAA output settling time TEA6846H CONDITIONS MIN. TYP. MAX. UNIT 0.2 V < VDAAOUT < 8.25 V; CL = 270 pF - - 30 s RR ripple rejection fripple = 100 Hz; VDDA4 = 1 mV - 50 - dB CL DAA output load capacitance VDAAOUT < 8.0 V; FM mode - - 270 pF A DAA TEMPERATURE COMPENSATION: PIN DAATD Isource compensation diode source current 0.2 V < VDAATD < 1.5 V -50 -40 -30 TCsource temperature coefficient of compensation diode source current 0.2 V < VDAATD < 1.5 V; Tamb = -40 to +85 C -300 - +300 - 8 - bit data byte 4: bit 7 = 1 - 2 - ms data byte 4: bit 7 = 0 - 20 - ms data byte 4: bit 3 = 1 - 10 - data byte 4: bit 3 = 0 - 100 - - 272 - - 75.368 - kHz -6 10 ----------K IF counter (FM IF or AM IF2 counter) NIF IF counter length for AM and FM Tcount(IF) IF counter period Rprecount FM IF counter prescaler ratio Reference frequency for car sound processor IC; note 3 REFERENCE FREQUENCY DIVIDER Nref crystal oscillator divider ratio fref reference frequency fxtal = 20.5 MHz VOLTAGE GENERATOR; PIN FREF Vo(p-p) AC output voltage (peak-to-peak value) 60 100 170 mV VO DC output voltage 3.2 3.4 3.9 V Ro output resistance - - 50 k RL(min) minimum load resistance 1 - - M data byte 5: bit 5 = 0, bit 6 = 0 - 150 - mV data byte 5: bit 5 = 1, bit 6 = 0 - 275 - mV data byte 5: bit 5 = 0, bit 6 = 1 - 400 - mV data byte 5: bit 5 = 1, bit 6 = 1 - 525 - mV 0.20 0.27 0.35 V - 15 - mA AM signal channel AM RF AGC STAGE INPUTS: PINS AMMIX1IN1 AND AMMIX1IN2 Vi(p) RF input voltage for AGC start level (peak value) AM IF AGC STAGE INPUTS: PINS AMIF2IN AND AMIF2DEC Vi(p) IF2 input voltage (peak value) AGC start level AM RF AGC CURRENT GENERATOR OUTPUT: PIN IAMAGC Isink(max) 2003 Feb 04 maximum AGC sink current VAMMIX1IN1 > 500 mV (peak value) 15 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER Ro output resistance Co output capacitance TEA6846H CONDITIONS IIAMAGC = 1 A MIN. TYP. MAX. UNIT 1 - - M - 5 7 pF AM RF AGC PEAK DETECTOR: PIN T2AMAGC Iatt attack current AGC peak detector data byte 5: bit 5 = 1, bit 6 = 1; AM mixer 1 input Vi = 1 V; VT2AMAGC-GND = 3 V; VAMIF2IN-AMIF2DEC = 0 V - -3.15 - mA Idec decay current AGC peak detector data byte 5: bit 5 = 1, bit 6 = 1; AM mixer 1 input Vi = 0 V; VT2AMAGC-AMMIX1IN2 = 0.25 V; VT2AMAGC-GND = 3 V; VAMIF2IN-AMIF2DEC = 0 V - 2.6 - A AM MIXER 1 (IF1 = 10.7 MHZ) Mixer inputs: pins AMMIX1IN1 and AMMIX1IN2 Ri input resistance note 4 50 70 100 k Ci input capacitance note 4 - 5 7 pF VI DC input voltage 2.3 2.7 3.1 V Vi(max) maximum voltage on pin AMMIX1IN1 500 - - mV 1 dB compression point of AM mixer 1 output (peak-to-peak) Mixer outputs: pins MIX1OUT1 and MIX1OUT2 Ro output resistance note 5 100 - - k Co output capacitance note 5 - 5 7 pF Vo(max)(p-p) maximum output voltage (peak-to-peak value) 12 15 - V Ibias mixer bias current 4.8 6 7.2 mA 3.2 mA --------V AM mode Mixer gm(conv) conversion transconductance I MIX1OUT1 --------------------------------------------------V FMMIXIN1 - FMMIXIN2 2.0 2.55 gm(conv)(T) conversion transconductance variation with temperature g m(conv) --------------------------------g m(conv) x T - -9 x 10-4 - IP3 3rd-order intermodulation RL = 2.8 k (AC load between 135 output pins) 138 - dBV IP2 2nd-order intermodulation RL = 2.8 k (AC load between - output pins) 170 - dBV 2003 Feb 04 16 K-1 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER Vi(n)(eq) equivalent input noise voltage F noise figure of AM mixer 1 TEA6846H CONDITIONS MIN. TYP. MAX. UNIT band limited noise; - Rgen = 750 ; RL = 2.8 k (AC load between output pins) 5.8 - - 4.5 7.1 dB -5 - +5 A nV -----------Hz WEATHER BAND FLAG: PIN T1AMAGC IL(max) maximum load current Vo(max) maximum output voltage for FM mode measured with respect to pin RFGND 0 - 0.5 V Vo(min) minimum output voltage for WX mode measured with respect to pin RFGND 5.1 6.0 6.9 V AM MIXER 2 (IF2 = 450 kHz) Mixer inputs: pins IFAMP1IN and IFAMP1DEC Ri input resistance note 6 270 330 390 Ci input capacitance note 6 - 5 7 pF VI DC voltage 2.4 2.7 3 V Vi(max)(p) maximum input voltage (peak value) 1.1 - - V 100 - - k 1 dB compression point of AM mixer 2 output (peak-to-peak) Mixer outputs: pins AMMIX2OUT1 and AMMIX2OUT2 R0 output resistance note 7 Co output capacitance note 7 - 5 7 pF Vo(max)(p-p) maximum output voltage (peak-to-peak value) VDDA = 8.5 V 12 15 - V Ibias mixer bias current AM mode 3.6 4.5 5.4 mA 1.9 mA --------V Mixer gm(conv) conversion transconductance I AMMIX2OUT1 ------------------------------V IFAMP1IN 1.3 1.6 gm(conv)(T) conversion transconductance variation with temperature g m(conv) --------------------------------g m(conv) x T - -9 x 10-4 - IP3 3rd-order intermodulation RL = 4 k (AC load between output pins) 134 137 - dBV IP2 2nd-order intermodulation RL = 4 k (AC load between output pins) - 170 - dBV Vi(n)(eq) equivalent input noise voltage Rgen = 330 ; RL = 4 k - (AC load between output pins) 15 22 nV -----------Hz F noise figure of AM mixer 2 - 16 19.5 dB 2003 Feb 04 17 K-1 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT AM IF2 AGC STAGE: PINS AMIF2IN AND AMIF2DEC; note 8 Vi input voltage for = -10 dB audio attenuation AM soft mute on - 75 120 V AM soft mute off - 6 10 V VAGC(start) AGC start voltage input carrier voltage - 14 30 V VAGC(stop) AGC stop voltage maximum input peak voltage 1 - - V VAGC(ctrl) AGC control voltage Vi = 1 mV 4.1 4.3 4.7 V AGC AGC range between start and stop of AGC; m = 0.8 - 89 - dB Ri input resistance 1.8 2 2.2 k Ci input capacitance - - 5 pF - 45 65 V AM DETECTOR Vsens(rms) sensitivity voltage (RMS value) m = 0.3; fmod = 400 Hz; BAF = 2.5 kHz; Rgen = 2 k; note 8 (S+N)/N = 26 dB (S+N)/N = 46 dB (S+N)/N maximum signal plus noise-to-noise ratio m = 0.3; fmod = 400 Hz; BAF = 2.5 kHz; Rgen = 2 k THD total harmonic distortion BAF = 2.5 kHz; CAGC = 22 F; AM IF2 AGC input Vi = 100 V to 500 mV (RMS) - 600 900 V 54 60 - dB m = 0.8; fmod = 400 Hz - 0.5 1 % m = 0.9; fmod = 400 Hz - 1 2 % m = 0.8; fmod = 100 Hz - 1.25 2.5 % - 1.75 3.5 % RR ripple rejection VDDA2(ripple) = 100 mV (RMS); fripple = 100 Hz 30 40 - dB tsw FM to AM switching time CAGC = 22 F - 1000 1500 ms tsettle AM AGC settling time CAGC = 22 F normal operation - - 1800 ms test mode - - 180 ms minimum at Vi = 14 V 1.5 3 4.5 mV maximum at Vi = 5.0 mV 130 180 230 mV AM mono; m = 0.3; 240 fmod = 400 Hz; Vi = 100 V to 500 mV (RMS) 290 340 mV m = 0.9; fmod = 100 Hz Output: pin AMAFIF2 Vo(rms) Ro 2003 Feb 04 AM IF2 output voltage (RMS value) output resistance AM stereo; m = 0 AM stereo - - 500 AM mono - - 500 18 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT - 5 7 pF Vi = 10 V to 1 V 0 - 7 V Vi < 1 V; standard setting of level DAA and level slope 0.1 0.5 0.9 V Vi = 1.4 mV; standard setting of level DAA 1.6 2.2 2.8 V Vlevel step size for adjustment of standard setting of level slope 30 level starting point 40 50 mV Vlevel(slope) slope of level voltage 800 950 mV --------------20 dB Vstep step size for adjustment of Vi =1.4 mV level slope 45 60 75 mV --------------20 dB Blevel bandwidth of level output voltage 200 300 - kHz Ro output resistance - - 500 RR ripple rejection - 40 - dB Co output capacitance AM mono AM IF2 LEVEL DETECTOR OUTPUT: PIN Vlevel; see Fig.3 Vlevel DC output voltage standard setting of level slope 650 VDDA1(ripple) = 100 mV (RMS); fripple = 100 Hz AM NOISE BLANKER; see Fig.4 Threshold: pin AMNBHOLD VO DC output voltage 4.3 4.6 5.1 V tsup suppression time 6 7.5 10 s ftrigger trigger sensitivity frequency Vpulse = 200 mV (peak); Vlevel < 1.8 V - 1000 - Hz Vpulse = 200 mV (peak); Vlevel > 2.2 V - - 100 Hz Vpulse = 20 mV (peak); Vlevel < 1.8 V - - 100 Hz Noise detector output: pin TRDSMUTE Isink(AGC) AM noise blanker AGC sink current VTRDSMUTE = 3 V 35 50 65 A VAGC AM noise blanker AGC voltage AM mixer 1 input Vi = 0 V 1.9 2.2 2.5 V data byte 5: bit 5 = 0, bit 6 = 0 - 4 - mV data byte 5: bit 5 = 1, bit 6 = 0 - 8 - mV data byte 5: bit 5 = 0, bit 6 = 1 - 12 - mV data byte 5: bit 5 = 1, bit 6 = 1 - 16 - mV FM signal channel FM RF AGC Inputs: pins FMMIXIN1 and FMMIXIN2; note 9 Vi(RF)(rms) 2003 Feb 04 RF input voltage for start of wide-band AGC (RMS value) 19 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT AGC peak detector output: pin T1FMAGC Ich charge current -350 -600 -850 A Idch discharge current 15 25 35 A Vo = 0.5 to 4.0 V 8 11.5 15 mA data byte 5: bit 7 = 1; standard setting of level DAA 500 950 1400 mV FM mode 6.5 7.1 7.9 V AM mode 2.7 3.1 3.4 V PIN diode drive output: pin IFMAGC Idrive drive current Level voltage output: pin Vlevel Vth threshold voltage for narrow-band AGC FM RF MIXER Reference voltage: pin Vref(FMMIX) Vref reference voltage Inputs: pins FMMIXIN1 and FMMIXIN2; note 9 Vi(RF)(max) maximum RF input voltage 1 dB compression point of FM mixer output voltage (peak-to-peak value) 70 100 - mV Vi(n)(eq) equivalent input noise voltage Rgen = 600 ; RL = 2.8 k - 2.6 3.1 nV -----------Hz Ri input resistance - 1.4 - k Ci input capacitance - 5 7 pF Outputs: pins MIX1OUT1 and MIX1OUT2; note 5 Ro output resistance 100 - - k Co output capacitance - 5 7 pF Ibias mixer bias current 4.8 6 7.2 mA Vo(max)(p-p) maximum output voltage (peak-to-peak value) 3 - - V gm(conv) conversion transconductance 8.5 12.5 18 mA --------V gm(conv)(T) conversion transconductance variation with temperature - -1 x 10-3 - K-1 F noise figure - 3 4.6 dB IP3 3rd-order intermodulation 116 119 - dBV IRR image rejection ratio 25 30 - dB 13.5 15.5 17.5 dB FM mode FM mixer IF AMPLIFIER 1 RL = 330 ; Vi = 1 mV; note 10 G gain F noise figure - 10 13 dB IP3 3rd-order intermodulation 117 120 - dBV 2003 Feb 04 20 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT Inputs: pins IFAMP1IN and IFAMP1DEC; note 10 Vi(max)(p) maximum input voltage (peak value) 1 dB compression point of IF amplifier 1 output voltage (peak value) 200 - - mV Vi(n)(eq) equivalent input noise voltage Rgen = 330 ; RL = 330 - 8 10 nV -----------Hz Ri input resistance 270 330 390 Ci input capacitance - 5 7 pF 1.2 1.5 - V Output: pin IFAMP1OUT Vo(max)(p) maximum output voltage (peak value) Ro output resistance 270 330 390 Co output capacitance - 5 7 pF 6.5 8.5 10.5 dB IF AMPLIFIER 2 RL = 330 ; Vi = 1 mV; note 11 G gain F noise figure - 13 15 dB IP3 3rd-order intermodulation 127 130 - dBV Inputs: pins IFAMP2IN and IFAMP2DEC; note 11 Vi(max)(p) maximum input voltage (peak value) 1 dB compression point of IF amplifier 2 output voltage (peak value) 500 - - mV Vi(n)(eq) equivalent input noise voltage Rgen = 330 ; RL = 330 - 10 13 nV -----------Hz Ri input resistance 270 330 390 Ci input capacitance - 5 7 pF Output: pin IFAMP2OUT Vo(max)(p) maximum output voltage (peak value) 1.2 1.5 - V Ro output resistance 270 330 390 Co output capacitance - 5 7 pF 74 80 - dB FM demodulator and level detector; see Figs 5 and 6 FM LIMITER Inputs: pins FMLIMIN and FMLIMDEC; note 12 Rgen = 50 G gain Ri input resistance 270 330 390 k Ci input capacitance - 5 7 pF 500 700 - mV Outputs: pins QDET1 and QDET2 Vo(p-p) 2003 Feb 04 output voltage (peak-to-peak value) measured between output pins 21 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT FM DEMODULATOR RL load resistance 20 - - k CL load capacitance - - 50 pF - 10 15 V (S+N)/N = 26 dB - 10 15 V (S+N)/N = 46 dB - 50 75 V 180 230 280 mV - - 100 A FM limiter inputs: pins FMLIMIN and FMLIMDEC; note 12 Vstart(lim)(rms) start of limiting of MPX output voltage (RMS value) AF = -3 dB Vo(sens)(rms) f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s sensitivity for MPX output voltage (RMS value) RDS MPX output: pin RDSMPX Vo(rms) RDS MPX output voltage (RMS value) Io(max) maximum RDS MPX output current f = 22.5 kHz; fmod = 57 kHz; Vi = 20 V to 1 V; note 12 Ro output resistance - - 500 B bandwidth RDS MPX output CL = 0; RL > 20 k 200 300 - kHz PSRR power supply ripple rejection fripple = 100 Hz to 20 kHz - 40 - dB 180 230 280 mV Vi = 500 V to 300 mV 50 60 - dB Vi = 20 to 500 V - 40 - dB Vi = 300 mV to 1 V - 40 - dB - - 100 A 67 70 - dB FM MPX output: pin FMMPX; note 12 Vo(rms) MPX output voltage (RMS value) f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; Vi = 20 V to 1 V AM AM suppression of MPX output f = 22.5 kHz; fmod = 1 kHz; m = 0.3; de-emphasis = 75 s Io(max) maximum MPX output current (S+N)/N maximum signal plus noise-to-noise ratio of MPX output voltage THD total harmonic distortion of f = 75 kHz; fmod = 1 kHz; MPX output voltage de-emphasis = 75 s; Vi = 200 V to 800 mV - 0.35 0.7 % B bandwidth MPX output CL = 0; RL > 20 k 200 - - kHz PSRR power supply ripple rejection fripple = 100 Hz to 20 kHz - 40 - dB RL(min) minimum load resistance 20 - - k 2003 Feb 04 f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; Vi = 10 mV 22 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT Ro(max) maximum output resistance - - 500 CL(max) maximum load capacitance - - 50 pF MPX MUTE mute muting depth during RDS update 60 80 - dB tatt attack time MPX mute CTRDSMUTE = 10 nF 0.75 1 1.25 ms tdecay decay time MPX mute CTRDSMUTE = 10 nF 0.75 1 1.25 ms RDS update: pin TRDSMUTE Idch discharge current Vo = 3 V; audio output muted 24 32 38 A Ich charge current Vo = 3 V; audio output not muted -38 -32 -24 A f = 100 kHz 28 32 - dB Vi = 10 to 80 V - 0.1 1 V Vi = 80 V to 800 mV - 10 30 mV Vi = 10 to 80 V - 0.240 1 V Vi = 80 V to 800 mV - 25 500 mV Vi = 10 V to 1 V 0 - 7 V Vi < 1 V; standard setting of level DAA 0.2 0.6 1.1 V Vi = 1 mV; standard setting of level DAA 1.4 1.9 2.5 V DEMODULATOR AFC GAFC AFC gain RDS MPX output: pin RDSMPX; note 12 Voffset(DC) residual DC offset voltage Ldemod = typical value Ldemod = 6% FM IF LEVEL DETECTOR OUTPUT: PIN Vlevel; note 12 Vlevel DC output voltage Vlevel level starting point for adjustment of step size standard setting of level slope 30 40 50 mV Vlevel(slope) slope of level voltage standard setting of level slope 650 800 950 mV --------------20 dB Vstep level slope adjustment of step size Vi = 1 mV 45 50 75 mV --------------20 dB Blevel bandwidth of level output voltage Vi = 10 mV; fmod = 22.5 kHz; standard setting of level DAA 200 300 - kHz Ro output resistance - - 500 RR ripple rejection - 40 - dB 2003 Feb 04 VDDA1(ripple) = 100 mV (RMS); fripple = 100 Hz 23 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio SYMBOL PARAMETER TEA6846H CONDITIONS MIN. TYP. MAX. UNIT RDS update Output: pin AFHOLD Isink(max) maximum sink current after first bus transmission with AF = 1 (start of RDS update); Vo = 0.5 V 1.0 1.2 1.4 mA no RDS update in progress; Vo = 0.5 V 1.0 1.2 1.4 mA VDAATD(L) = 2.5 V; VDAATD(H) = 3.5 V 2.5 - 3.5 V VSCL(L) = 0 V; VSCL(H) = 5 V 0 - 5 V pin FREF in test mode 5.1 6 6.9 V Output: pin AFSAMPLE Isink(max) maximum sink current Test mode; note 3 Temperature compensation diode: pin DAATD Vi(ext) external input voltage to clock state machine Clock input: pin SCL Vi(ext) external input voltage to clock DAA Time constant output: pin T1AMAGC Vpulse enabling voltage of load PLL signal Notes 1. Measured between pins XTAL1 and XTAL2. n 2. DAA conversion gain formula: V DAAOUT = 2 x 0.75 x ---------- + 0.25 x ( V DAAIN + V DAATD ) - V DAATD 128 where n = 0 to 127. 3. Reference frequency pin FREF: a) Rext = 68 k connected to ground activates the 2nd I2C-bus address b) Rext = 100 k connected to VDDA1 sets the IC into test mode. 4. Input parameters of AM mixer 1 measured between pins AMMIX1IN1 and AMMIX1IN2. 5. Output parameters of FM mixer and AM mixer 1 measured between pins MIX1OUT1 and MIX1OUT2. 6. Input parameters of AM mixer 2 measured between pins IFAMP1IN and IFAMP1DEC. 7. Output parameters of AM mixer 2 measured between pins AMMIX2OUT1 and AMMIX2OUT2. 8. Input parameters of AM IF2 measured between pins AMIF2IN and AMIF2DEC. 9. Input parameters of FM mixer measured between pins FMMIXIN1 and FMMIXIN2. 10. Input parameters of IF amplifier 1 measured between pins IFAMP1IN and IFAMP1DEC. 11. Input parameters of IF amplifier 2 measured between pins IFAMP2IN and IFAMP2DEC. 12. Input parameters of FM limiter measured between pins FMLIMIN and FMLIMDEC. 2003 Feb 04 24 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H MHB484 6 Vlevel handbook, full pagewidth (V) 5 4 (1) 3 (2) 2 (3) 1 0 10 -3 10 -2 10 -1 1 10 2 10 VAMIF2IN (mV) 10 3 (1) Level DAA setting byte 6 = FFH. (2) Level DAA setting byte 6 = 84H (standard setting). (3) Level DAA setting byte 6 = 00H. Fig.3 AM level output voltage (DAA) as a function of AM level circuit input voltage. handbook, full pagewidth Trep 70 Vlevel 71 Vpulse TEA6846H 73 1 k VXTAL2 78 test signal 1 k 77 18 50 19 8.5 V 14 oscilloscope, counter 4.7 nF 100 Vpulse 100 VIFAMP1IN MHB883 8.5 V VIFAMP1IN = 4 V. VXTAL2 = 3 V. Test signal: Trep = 2 ms, tr < 50 ns, tf < 50 ns and duty factor 50%. Fig.4 Test circuit for AM noise blanker. 2003 Feb 04 25 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H MHB486 6 handbook, full pagewidth Vlevel (V) 5 (1) 4 (2) 3 2 (3) 1 0 10 -3 10 -2 10 -1 1 10 10 2 10 3 VFMLIMIN (mV) (1) Level DAA setting byte 6 = FFH. (2) Level DAA setting byte 6 = 84H (standard setting). (3) Level DAA setting byte 6 = 00H. Fig.5 FM level output voltage (DAA) as a function of FM limiter and level circuit input voltage. 2003 Feb 04 26 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H MHB487 10 FMMPX VRDSMPX (dB) 0 handbook, V full pagewidth , (1) 9 Vlevel (V) 8 THD (%) -10 7 -20 6 -30 -40 (2) 5 (3) 4 -50 3 -60 2 (4) -70 1 (5) -80 10 -3 10 -2 10 -1 1 10 0 10 3 10 2 VFMLIMIN (mV) (1) Output voltage for FMMPX and RDSMPX: fIF = 10.7 MHz; f = 22.5 kHz; fmod = 1 kHz. (2) Noise: unweighted B = 250 Hz to 15 kHz with de-emphasis 50 s for FMMPX. (3) Noise: unweighted B = 250 Hz to 15 kHz with de-emphasis 50 s for RDSMPX. (4) THD for FMMPX and RDSMPX. (5) Level for standard setting of level DAA, byte 6 = 84H. Fig.6 (S+N)/N, THD and level output voltage for FM mode as a function of FM demodulator input voltage. 2003 Feb 04 27 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H Bit 7 of each byte is considered the MSB and has to be transferred as the first bit of the byte. 12 I2C-BUS PROTOCOL 12.1 I2C-bus specification The data becomes valid at the output of the internal latches with the acknowledge of each byte. A STOP condition after any byte can shorten transmission times. Information about the I2C-bus can be found in the brochure "The I2C-bus and how to use it" (order number 9398 393 40011). When writing to the transceiver by using the STOP condition before completion of the whole transfer: The standard I2C-bus specification is expanded by the following definitions. * The remaining bytes will contain the old information IC addresses: * If the transfer of a byte is not completed, this byte is lost and the previous information is available. * 1st IC address C2: 1100001 * 2nd IC address C0: 1100000. Structure of the increment. I2C-bus In byte 5, 4 bits are reserved for test mode purposes. Those can only be used when the test mode is activated by the select pin FREF. logic: slave transceiver with auto Subaddresses are not used. Exception to the standard I2C-bus 12.1.3 specification: When the IC is used together with the TEA688x or TEF689x and both SCL and SDA lines are connected via the I2C-bus to the TEA688x or TEF689x, the pull-up resistors of the tuner IC should be connected to the digital supply voltage of the TEA688x or TEF689x. Otherwise an I2C-bus pull-down can occur switching off the tuner IC supply when the I2C-bus buffer interface of the TEA688x or TEF689x is enabled for data transfer to the tuner IC. * The data hold time tHD;DAT must be at least 1 s. 12.1.1 TEST MODE Connecting pin FREF to VDDA1 via a 100 k resistor or feeding 50 A into that pin switches the IC into the test mode. During test mode the digital-to-analog converters of the level and antenna DAA functions can be sequenced by the I2C-bus SCL line. 12.1.4 * First: bit MUTE = 1 * Second: bit MUTE = 0. DATA TRANSFER Data sequence: address, byte 1, byte 2, byte 3, byte 4, byte 5, and byte 6. The data transfer has to be in this order. The LSB = 0 indicates a WRITE operation to the TEA6846H. 2003 Feb 04 FREQUENCY SETTING For new frequency setting, in both AM and FM mode, the programmable divider is enabled by setting bit MUTE = 1. To select an FM frequency, two I2C-bus transmissions are necessary: During test mode either the TEA688x or TEF689x reference frequency, the PLL reference frequency divider or the programmable divider output can be switched to pin FREF. 12.1.2 I2C-BUS PULL-UP RESISTORS 28 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H I2C-bus protocol 12.2 12.2.1 DATA TRANSFER MODE AND IC ADDRESS Table 1 Write mode S(1) address (write) A(2) address (read) A(2) data byte 1 0 0 0 0/1(1) R/W(2) data byte(s) A(2) P(3) Notes 1. S = START condition. 2. A = acknowledge. 3. P = STOP condition. Table 2 Read mode S(1) Notes 1. S = START condition. 2. A = acknowledge. Table 3 IC address byte IC ADDRESS 1 1 0 MODE Notes 1. Defined by address pin FREF: a) 1 = 1st IC address b) 0 = 2nd IC address. 2. Read or write mode: a) 0 = write operation to TEA6846H b) 1 = read operation from TEA6846H. 12.2.2 WRITE MODE: DATA BYTE 1 Table 4 Format of data byte 1 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 AF PCA6 PCA5 PCA4 PCA3 PCA2 PCA1 PCA0 Table 5 Description of data byte 1 bits BIT SYMBOL 7 AF Alternative frequency. If AF = 0, then normal operation. If AF = 1, then AF (RDS) update mode. 6 to 0 PCA[6:0] Setting of programmable counter of synthesizer PLL. Upper byte of PLL divider word. 2003 Feb 04 DESCRIPTION 29 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 12.2.3 TEA6846H WRITE MODE: DATA BYTE 2 Table 6 Format of data byte 2 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 PCB7 PCB6 PCB5 PCB4 PCB3 PCB2 PCB1 PCB0 Table 7 Description of data byte 2 bits BIT SYMBOL 7 to 0 PCB[7:0] DESCRIPTION Setting of programmable counter of synthesizer PLL. Lower byte of PLL divider word. WRITE MODE: DATA BYTE 3 12.2.4 Table 8 Format of data byte 3 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 MUTE DAA6 DAA5 DAA4 DAA3 DAA2 DAA1 DAA0 Table 9 Description of data byte 3 bits BIT SYMBOL 7 MUTE 6 to 0 DAA[6:0] 12.2.5 DESCRIPTION FM audio mute. If MUTE = 0, then FM audio not muted. If MUTE = 1, then FM audio muted; writing to programmable divider enabled. Setting of antenna digital auto alignment. WRITE MODE: DATA BYTE 4 Table 10 Format of data byte 4 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 IFMT RFS2 RFS1 RFS0 IFPR BND1 BND0 AMFM Table 11 Description of data byte 4 bits BIT SYMBOL 7 IFMT 6 to 4 RFS[2:0] 3 IFPR IF counter prescaler ratio. If IFPR = 0, then IF prescaler ratio is 100. If IFPR = 1, then IF prescaler ratio is 10. 2 and 1 BND[1:0] Band switch. These 2 bits select in FM mode band and local or distant, see Table 13; in AM mode band and AM stereo, see Table 14. 0 AMFM 2003 Feb 04 DESCRIPTION IF measuring time. If IFMT = 0, then IF measuring time is 20 ms. If IFMT = 1, then IF measuring time is 2 ms. Reference frequency for synthesizer. These 3 bits determine the reference frequency, see Table 12. AM or FM switch. If AMFM = 0, then FM mode. If AMFM = 1, then AM mode 30 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H Table 12 Reference frequency setting RFS2 RFS1 RFS0 fref (kHz) 0 0 0 100 1 0 0 50 0 1 0 25 1 1 0 20 0 0 1 10 1 0 1 10 0 1 1 10 1 1 1 10 Table 13 FM mode BND1 BND0 SELECTION 0 0 FM standard: dead zone high current charge pump active, FM AGC defined by RF level and threshold level setting by I2C-bus 0 1 FM local: dead zone high current charge pump active, FM AGC source current set to maximum 1 0 FM East Europe: dead zone high current charge pump switched off, current of low current charge pump set to 1 mA 1 1 FM weather band: N1 divider set to 1 and I and Q phase shift network switched on, WX flag signal activated BND1 BND0 SELECTION 0 0 AM mono; N2 divider set to 5 (SW) 0 1 AM stereo; N2 divider set to 5 (SW) 1 0 AM mono; N2 divider set to 10 (LW, MW) 1 1 AM stereo; N2 divider set to 10 (LW, MW) Table 14 AM mode; note 1 Note 1. In AM mode dead zone high current charge pump switched off, current of low current charge pump set to 1 mA. 2003 Feb 04 31 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 12.2.6 TEA6846H WRITE MODE: DATA BYTE 5 Table 15 Format of data byte 5 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 KAGC WBA1 WBA0 AMSM TMS3 TMS2 TMS1 TMS0 Table 16 Description of data byte 5 bits BIT SYMBOL DESCRIPTION 7 KAGC 6 and 5 WBA[1:0] 4 AMSM AM soft mute. If AMSM = 0, then AM soft mute is off. If AMSM = 1, then AM soft mute is on. 3 TMS3 In test mode charge pump 3-state. If TMS3 = 0, then 3-state off. If TMS3 = 1, then 3-state on. 2 TMS2 In test mode external clock for level and antenna DAA. If TMS2 = 0, then external clock disabled. If TMS2 = 1, then external clock enabled. 1 and 0 TMS[1:0] Keyed FM AGC. If KAGC = 0, then keyed FM AGC is off. If KAGC = 1, then keyed FM AGC is on. Wide band AGC. These 2 bits set the start value of wide band AGC. For AM, see Table 17 and for FM, see Table 18. In test mode setting of pin FREF. These 2 bits define the function of pin FREF, see Table 19. Table 17 Setting of wide band AGC for AM WBA1 WBA0 AM MIXER 1 INPUT VOLTAGE (PEAK VALUE) (mV) 0 0 150 0 1 275 1 0 400 1 1 525 WBA1 WBA0 FM RF MIXER INPUT VOLTAGE (RMS VALUE) (mV) 1 1 4 1 0 8 0 1 12 0 0 16 Table 18 Setting of wide band AGC for FM Table 19 Setting function of pin FREF in test mode TMS1 TMS0 0 0 reference frequency of TEA688x or TEF689x 0 1 tuner oscillator frequency divided by division ratio of programmable divider 1 0 PLL synthesizer reference frequency 1 1 not used (no output) 2003 Feb 04 OUTPUT AT PIN FREF 32 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 12.2.7 TEA6846H WRITE MODE: DATA BYTE 6 Table 20 Format of data byte 6 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 LST4 LST3 LST2 LST1 LST0 LSL2 LSL1 LSL0 Table 21 Description of data byte 6 bits BIT SYMBOL DESCRIPTION 7 to 3 LST[4:0] Setting of level DAA starting point. These 5 bits determine the offset of the level detector output voltage. 2 to 0 LSL[2:0] Setting of level DAA slope. These 3 bits determine the steepness of the level detector output voltage. Table 22 Standard setting of data byte 6 bits SETTING OF LEVEL DAA STARTING POINT SETTING OF LEVEL DAA SLOPE LST4 LST3 LST2 LST1 LST0 LSL2 LSL1 LSL0 1 0 0 0 0 1 0 0 12.2.8 READ MODE: DATA BYTE 1 Table 23 Format of 1st data byte BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 IFC7 IFC6 IFC5 IFC4 IFC3 IFC2 IFC1 IFC0 Table 24 Description of data byte 1 bits BIT SYMBOL 7 to 0 IFC[7:0] 2003 Feb 04 DESCRIPTION IF counter result. These bits contain the last eight bits of the IF counter result. 33 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H 13 TEST AND APPLICATION INFORMATION handbook, full pagewidth A Vtune Coils: L1: P826RC-5134N=S L2: PSGAE-5078D=S L3: P293BC-1977Z L4: E543SNAS-02010 L5: 611SNS-1066Y L6: 369INS-3076X L7; 388BN-1211Z L8: air coil (1): 1 to 5 pF trimmer without DAA (2): series NP0 antenna 5V digital 3.3 nF 2.2 k 22 3.9 nF B fref PLL 10 k 3.3 H 1.2 k 100 nF DGND 22 nF 100 nF 42 40 2.2 M 43 44 46 45 47 39 22 k Vt 3.3 H 38 ANTENNA DAA C TUNING SYSTEM BAS16 BB814 D AM L5 10.25 MHz (1) E 120 nH 270 nH 37 8.2 pF 36 1 F 15 pF 290 nH TEA6846H WX x 8.2 pF 31 22 BA595 F 33 L6 BA595 N1 /2 90 FM I/Q MIXER 30 G 330 2.2 k 1 nF FM AGC 1 F L8 290 nH 35 29 10 F 15 pF 1 nF H RFGND AM-NOISE DETECTOR 90 PEAK/ AVERAGE I 22 nF J 5V analog BAQ806 1 k 28 27 100 nF 6.8 H 22 F 100 pF 150 H N x 180 H 150 pF 10 k O P 100 nF BAV99 IFAMP1 AM MIXER 1 22 470 pF M 20 19 18 17 16 14 180 pF 1.5 k L7 /5/10 220 nF 1.8 M 10 nF L N2 AM RF AGC 23 22 nF 270 H 10 nF 26 WB FLAG 560 K 1 nF 22 nF 22 nF 22 nF BF861C 2.2 M 47 22 SFE10.7 MS3 L1 22 nF 22 10 Q MHB880 Fig.7 Application diagram (continued in Fig.8). 2003 Feb 04 34 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio handbook, full pagewidthA TEA6846H (2) 4.7 k 270 pF AF AF SAMPLE HOLD B AM RDS/ AUDIO/IF MPX FM MPX 8.5 V 3.3 H 5V analog 1 H L4 BB156 22 22 nF 2.7 1.8 pF pF 48 49 53 54 55 SEQUENTIAL CIRCUIT FOR RDS UPDATING VCO C 47 F 47 F 47 F 51 50 100 nF 100 nF 6.8 nF 56 57 AM DETECTOR 59 58 61 POWER SUPPLY MUTE VDD (I2C-bus) D 2 ms/ 20 ms E I2C-bus AM IF2 10 k 63 FM IF IF COUNT I2C-BUS F 10 k SDA 64 SCL 66 IF2GND 67 AM IF AGC G LEVEL DAA 4.7 k DEMODULATOR 68 69 H L3 AFC 47 F AM LEVEL BLANK PULSE I 70 AM/FM LEVEL J 71 K x L FM LIMITER/ LEVEL AM MIXER2 M CRYSTAL OSCILLATOR 72 20.5 MHz 73 76 N 220 nF 120 k IFAMP2 O L2 77 78 P 12 11 22 nF 9 8 7 6 5 4 220 nF 3 2 22 nF 1 330 22 nF IF1GND 79 22 nF 10 F 22 nF SFE10.7 MS3 SFE10.7 MS3 SFR450H 22 Q 8.5 V MHB881 Fig.8 Application diagram (continued from Fig.7). 2003 Feb 04 35 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H handbook, full pagewidth antenna input fref PLL FM RF input A B C Vtune D 10 k relay 1 2.2 k 3.3 nF 470 k 47 3.9 nF 100 nF 100 nF 22 1.2 k 100 nF relay 1 teledyne 3.3 H DGND 22 nF relay 2 100 nF 42 40 43 44 46 45 47 39 22 k Vt ANTENNA DAA 38 E BAS16 BB814 TUNING SYSTEM F AM 120 nH 10.25 MHz (1) 1.5 to 5 pF 8.2 pF 1 nF 100 nF 37 1 M 36 FM AGC 35 L8 470 nH 6.8 H H TEA6846H 1 F WX 33 4:6 BA779-2 47 pF x 31 560 pF 8.2 pF 3.3 H N1 /2 90 FM I/Q MIXER 30 22 I L5 BA779-2 J RFGND L7 220 nH 29 47 F 100 nF G AM NOISE DETECTOR 90 PEAK/ AVERAGE K 22 nF L 270 BAQ806 M 28 27 270 100 nF AM RF AGC 26 22 F N2 N /5/10 O P 220 nF WB FLAG 220 nF x 23 100 H 1 mH 100 pF 220 H 680 H IFAMP1 AM MIXER1 180 pF Q R 330 pF 22 1 nF 20 22 nF 22 nF 1.2 M 1 nF 16 14 50 1.5 k 470 pF 17 19 18 4.7 F BF861C 100 nF 22 nF Ce1 Ce2 BAV99 470 k 22 nF 47 22 22 L1 10 SFE10.7 MS3 S 100 nF 100 nF 100 nF 304 330 AM RF input Fig.9 Test circuit (continued in Fig.10). 2003 Feb 04 36 IF output 52 2 IF input MHB897 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio handbook, full pagewidth AF SAMPLE AM RDS/ AUDIO/IF MPX AF HOLD TEA6846H 10 FM MPX 47 F A 10 B C 47 F (1) 4.7 k 270 pF 68 k relay3 D L4 68 k 100 nF 100 nF 10 8.5 V 22 3.3 H 22 nF 100 nF 48 49 47 F 3.3 H 10 k 100 nF 100 nF 10 k 6.8 nF 47 F 47 F 50 51 53 55 54 56 57 58 59 61 SDA SEQUENTIAL CIRCUIT FOR RDS UPDATING VCO E AM DETECTOR F SCL POWER SUPPLY MUTE 2 ms/ 20 ms G FM IF I2C-bus I2C-bus interface 63 SDA AM IF2 IF COUNT I2C-BUS H 64 SCL 66 IF2GND 67 DGND AM IF AGC I LEVEL DAA DEMODULATOR 68 4.7 k L3 69 J AFC 47 F AM LEVEL BLANK PULSE K 70 AM/FM LEVEL L 71 M x N FM LIMITER/ LEVEL AM MIXER2 O CRYSTAL OSCILLATOR 72 20.5 MHz 73 76 P 220 nF 120 k IFAMP2 Q 77 L1: P7PSE-X398 L2: P7PSEAE-5078D = S L3: 392BC-1977Z L4: E543SNAS-02010 L5: 611SNS-1066Y L6: 369INS-3076X L7: MURATA LQN L8: MURATA LQN (1): series NP0 78 R 12 11 9 8 7 6 5 4 3 2 79 1 L2 330 22 nF 100 nF 220 nF 100 nF IF1GND 22 100 nF 22 F 22 nF coaxial connector test pin jumper SFR 450H SFE10.7 MS3 SFE10.7 MS3 to TEA6880H S 100 nF 100 nF 100 nF 304 330 FM IF1 output 52 100 nF 2 FM IF2 AM IF2 input input 100 nF 100 nF 304 2 k 47 330 FM IF2 output 2 52 2 k limiter input AM IF output Fig.10 Test circuit (continued from Fig.9). 2003 Feb 04 5V digital 100 nF 100 nF BB156 2.7 1.8 pF pF 5V analog 100 nF 37 MHB898 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H Table 25 DC operating points UNLOADED DC VOLTAGE (V) SYMBOL PIN AM MODE MIN. FM MODE TYP. MAX. MIN. TYP. MAX. FMLIMDEC 1 2.5 3 3.5 2.5 2.8 3.1 FMLIMIN 2 2.5 3 3.5 2.5 2.8 3.1 AMIF2DEC 3 2.4 2.7 3.2 floating IFAMP2OUT 4 7.2 7.9 - 3.4 3.9 4.4 AMNBHOLD 5 4.3 4.6 5.1 8 8.4 - AMIF2IN 6 2.4 2.7 3.2 IF1GND 7 external 0 IFAMP2IN 8 3 2.7 3.1 3.5 floating external 0 4 5 Coffset 9 floating 3 3.5 4 IFAMP2DEC 11 3 4 5 2.7 3.1 3.5 IFAMP1OUT 12 7.2 7.9 - 3.6 4 4.4 IFAMP1IN 14 2.4 2.7 3 2.3 2.7 3.1 2.7 3 2.7 3.1 0.3 (no WX) 0.5 (no WX) VDDA6 16 external 8.5 IFAMP1DEC 17 2.4 MIX1OUT1 18 external 8.5 external 8.5 2.3 external 8.5 MIX1OUT2 19 external 8.5 external 8.5 VDDA5 20 external 8.5 external 8.5 AMMIX1IN1 22 2.3 2.75 3.1 floating AMMIX1IN2 23 2.3 2.75 3.1 floating T1AMAGC 26 0 2.8 4.6 0 (no WX) T2AMAGC 27 2.5 2.8 3.1 floating IAMAGC 28 open-collector Vref(FMMIX) 29 2.7 3.1 3.4 6.5 open-collector 7.1 7.9 FMMIXIN2 30 1 1.3 1.6 2.3 2.8 3.3 RFGND 31 external 0 FMMIXIN1 33 1 1.3 1.6 2.3 2.8 3.3 IFMAGC 35 floating 1.5 (external biasing) - 4 (external biasing) T2FMAGC 36 7.5 T1FMAGC 37 floating DAAOUT 38 - DAATD 39 floating external 0 8 0.2 8.3 0.3 3.9 4.6 5.3 1 - 7 0.2 - 8.25 0.2 - 1.5 DAAIN 40 0 - 8.5 0 - 8.5 Vtune 42 0 - 8.5 0 - 8.5 CPOUT 43 0 - 8.5 0 - 8.5 VDDA4 44 external 8.5 FREF 45 3.2 3.4 3.7 3.4 3.7 2003 Feb 04 external 8.5 3.2 38 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H UNLOADED DC VOLTAGE (V) SYMBOL PIN AM MODE MIN. FM MODE TYP. MAX. MIN. VDDD 46 external 5 external 5 DGND 47 external 0 external 0 VCOGND 48 external 0 external 0 OSCFDB 49 2.2 2.8 3.4 6.1 7.2 OSCTNK 50 5 VDDA3 51 external 8.5 AFSAMPLE 53 0 AFHOLD 54 open-collector TRDSMUTE 55 1.9 TYP. MAX. 2.2 2.8 3.4 5 6.1 7.2 0.2 0.5 1.2 (muted) 1.7 (muted) external 8.5 0.2 0.5 0 open-collector 2.2 2.5 0.7 (muted) 5.2 (not muted) 5.7 (not muted) 6.2 (not muted) AMAFIF2 56 4 RDSMPX 57 floating 2.6 3.1 3.3 FMMPX 58 floating 3 3.5 4 VDDA2 59 external 5 external 5 VDDA1 61 external 8.5 SDA 63 4.8 5 5.2 4.8 5 5.2 SCL 64 4.8 5 5.2 4.8 5 5.2 IF2GND 66 external 0 external 0 QDET1 67 floating 3.6 4.1 4.6 QDET2 68 floating 3.6 4.1 4.6 CAFC 69 floating 1.2 3.4 4.1 Vlevel 70 0.05 - 7 0 - 7 XTAL1 71 1.7 2.1 2.5 1.7 2.1 2.5 XTALGND 72 external 0 XTAL2 73 1.7 2.1 2.5 1.7 2.1 2.5 IREF 76 4 4.25 4.5 4 4.25 4.5 AMMIX2OUT1 77 external 8.5 4.6 5.1 AMMIX2OUT2 78 external 8.5 CAGC 79 3.6 2003 Feb 04 4.3 4.6 floating external 8.5 external 0 external 8.5 external 8.5 4.3 4.8 4.1 39 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H 14 PACKAGE OUTLINE LQFP80: plastic low profile quad flat package; 80 leads; body 12 x 12 x 1.4 mm SOT315-1 c y X A 60 41 40 Z E 61 e E HE A A2 (A 3) A1 w M bp L pin 1 index 80 Lp 21 1 detail X 20 ZD e v M A w M bp D B HD v M B 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e mm 1.6 0.16 0.04 1.5 1.3 0.25 0.27 0.13 0.18 0.12 12.1 11.9 12.1 11.9 0.5 HD HE 14.15 14.15 13.85 13.85 L Lp v w y 1.0 0.75 0.30 0.2 0.15 0.1 Z D (1) Z E (1) 1.45 1.05 7 0o 1.45 1.05 o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT315-1 136E15 MS-026 2003 Feb 04 EIAJ EUROPEAN PROJECTION ISSUE DATE 99-12-27 00-01-19 40 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H If wave soldering is used the following conditions must be observed for optimal results: 15 SOLDERING 15.1 Introduction to soldering surface mount packages * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). * For packages with leads on two sides and a pitch (e): - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 15.2 - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Typical reflow peak temperatures range from 215 to 250 C. The top-surface temperature of the packages should preferable be kept below 220 C for thick/large packages, and below 235 C for small/thin packages. 15.3 15.4 Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. To overcome these problems the double-wave soldering method was specifically developed. 2003 Feb 04 Manual soldering 41 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio 15.5 TEA6846H Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE(1) WAVE BGA, LBGA, LFBGA, SQFP, TFBGA, VFBGA not suitable suitable(3) DHVQFN, HBCC, HBGA, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, HVQFN, HVSON, SMS not PLCC(4), SO, SOJ suitable LQFP, QFP, TQFP SSOP, TSSOP, VSO REFLOW(2) suitable suitable suitable not recommended(4)(5) suitable not recommended(6) suitable Notes 1. For more detailed information on the BGA packages refer to the "(LF)BGA Application Note" (AN01026); order a copy from your Philips Semiconductors sales office. 2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 3. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. 4. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 5. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 6. Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2003 Feb 04 42 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H 16 DATA SHEET STATUS LEVEL DATA SHEET STATUS(1) PRODUCT STATUS(2)(3) Development DEFINITION I Objective data II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Production This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 17 DEFINITIONS 18 DISCLAIMERS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Right to make changes Philips Semiconductors reserves the right to make changes in the products including circuits, standard cells, and/or software described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 2003 Feb 04 43 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H 19 PURCHASE OF PHILIPS I2C COMPONENTS Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011. 2003 Feb 04 44 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H NOTES 2003 Feb 04 45 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H NOTES 2003 Feb 04 46 Philips Semiconductors Product specification New In Car Entertainment (NICE) car radio TEA6846H NOTES 2003 Feb 04 47 Philips Semiconductors - a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. SCA75 (c) Koninklijke Philips Electronics N.V. 2003 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 753503/02/pp48 Date of release: 2003 Feb 04 Document order number: 9397 750 10547