HIP4080AIBT - Intersil Corporation

FN3658.7

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143 |Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

HIP4080A

80V/2.5A Peak, High Frequency Full Bridge

FET Driver

The HIP4080A is a high frequency, medium voltage Full

Bridge N-Channel FET driver IC, available in 20 lead plastic

SOIC and DIP packages. The HIP4080A includes an input

comparator, used to facilitate the “hysteresis” and PWM

modes of operation. Its HEN (high enable) lead can force

current to freewheel in the bottom two external power

MOSFETs, maintaining the upper power MOSFETs off.

Since it can switch at frequencies up to 1MHz, the HIP4080A

is well suited for driving Voice Coil Motors, switching power

amplifiers and power supplies.

HIP4080A can also drive medium voltage brush motors, and

two HIP4080As can be used to drive high performance

stepper motors, since the short minimum “on-time” can

provide fine micro-stepping capability.

Short propagation delays of approximately 55ns maximize

control loop crossover frequencies and dead-times which

can be adjusted to near zero to minimize distortion, resulting

in precise control of the driven load.

The similar HIP4081A IC allows independent control of all 4

FETs in a Full Bridge configuration.

The Application Note for the HIP4080A is AN9404.

Features

• Drives N-Channel FET Full Bridge Including High Side

Chop Capability

• Bootstrap Supply Max Voltage to 95VDC

• Drives 1000pF Load at 1MHz in Free Air at +50°C with

Rise and Fall Times of Typically 10ns

• User-Programmable Dead Time

• Charge-Pump and Bootstrap Maintain Upper Bias

Supplies

• DIS (Disable) Pin Pulls Gates Low

• Input Logic Thresholds Compatible with 5V to 15V Logic

Levels

• Very Low Power Consumption

• Undervoltage Protection

• Pb-Free Available as an Option

Applications

• Medium/Large Voice Coil Motors

• Full Bridge Power Supplies

• Switching Power Amplifiers

• High Performance Motor Controls

• Noise Cancellation Systems

• Battery Powered Vehicles

• Peripherals

• U.P.S.

Pinout

HIP4080A

(PDIP, SOIC)

TOP VIEW

Ordering Information

PART

NUMBER

TEMPERATURE

RANGE (°C) PACKAGE

PKG.

DWG. #

HIP4080AIPZ

(Note 1)

-40 to +85 20 Ld PDIP

(Pb-Free)

E20.3

HIP4080AIP -40 to +85 20 Ld PDIP E20.3

HIP4080AIB -40 to +85 20 Ld SOIC M20.3

HIP4080AIBZ

(Note 1)

-40 to +85 20 Ld SOIC

(Pb-Free)

M20.3

NOTES:

1. Intersil Pb-Free products employ special Pb-free material sets;

molding compounds/die attach materials and 100% matte tin

plate termination finish, which is compatible with both SnPb and

Pb-free soldering operations. Intersil Pb-Free products are MSL

classified at Pb-free peak reflow temperatures that meet or

exceed the Pb-free requirements of IPC/JEDEC J Std-020B.

2. Add “T” suffix for Tape and Reel packing option. HIP4080AIP not

available in Tape and Reel.

BHB

HEN

DIS

VSS

OUT

IN+

HDEL

IN-

LDEL

AHB

BHO

BLO

BLS

VDD

BHS

VCC

ALS

ALO

AHS

AHO

Data Sheet July 2004

Application Block Diagram

Functional Block Diagram (1/2 HIP4080A)

80V

GND

HIP4080A

GND

12V

LOAD

BHO

BHS

BLO

ALO

AHS

AHO

IN-

IN+

DIS

HEN

CHARGE

PUMP

VDD

HEN

DIS

OUT

IN+

IN_

HDEL

LDEL

VSS

TURN-ON

DELAY

TURN-ON

DELAY

DRIVER

AHB

AHO

AHS

VCC

ALO

ALS CBF

TO VDD (PIN 16)

CBS

DBS

HIGH VOLTAGE BUS ≤ 80VDC

+12VDC

LEVEL SHIFT

AND LATCH

BIAS

SUPPLY

UNDER-

VOLTAGE

HIP4080A

Typical Application (Hysteresis Mode Switching)

80V

12V

DIS

GND

1BHB

HEN

DIS

VSS

OUT

IN+

HDEL

IN-

LDEL

AHB

BHO

BLO

BLS

VDD

BHS

VCC

ALS

ALO

AHS

AHO

LOAD

HIP4080A/HIP4080

HIP4080A

Absolute Maximum Ratings Thermal Information

Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . -0.3V to 16V

Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V

Voltage on AHS, BHS . . . -6.0V (Transient) to 80V (25°C to 125°C)

Voltage on AHS, BHS . . . -6.0V (Transient) to 70V (-55°C to 125°C)

Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)

Voltage on AHB, BHB . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD

Voltage on ALO, BLO. . . . . . . . . . . . .VALS, BLS -0.3V to VCC +0.3V

Voltage on AHO, BHO . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA

Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns

All Voltages relative to VSS, unless otherwise specified.

Operating Conditions

Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . +9.5V to +15V

Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V

Voltage on AHB, BHB . . . . . . . .VAHS, BHS +5V to VAHS, BHS +15V

Input Current, HDEL and LDEL . . . . . . . . . . . . . . . .-500µA to -50µA

Operating Ambient Temperature Range . . . . . . . . . .-40°C to +85°C

Thermal Resistance (Typical, Note 3) θJA (°C/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Maximum Power Dissipation at +85°C

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .470mW

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530mW

Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C

Operating Max. Junction Temperature. . . . . . . . . . . . . . . . . . +125°C

Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300°C

(For SOIC - Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE:

3. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K, and

TA = +25°C, Unless Otherwise Specified

PARAMETERS SYMBOL TEST CONDITIONS

TJ = +25°C

TJ = - 40°C

TO +125°C

UNITSMIN TYP MAX MIN MAX

SUPPLY CURRENTS AND CHARGE PUMPS

VDD Quiescent Current IDD IN- = 2.5V, Other Inputs = 0V 8 11 14 7 14 mA

VDD Operating Current IDDO Outputs switching f = 500kHz, No Load 9 12 15 8 15 mA

VCC Quiescent Current ICC IN- = 2.5V, Other Inputs = 0V,

IALO = IBLO = 0

- 25 80 - 100 µA

VCC Operating Current ICCO f = 500kHz, No Load 1 1.25 2.0 0.8 3 mA

AHB, BHB Quiescent Current -

Qpump Output Current

IAHB, IBHB IN- = 2.5V, Other Inputs = 0V,

IAHO =I

BHO = 0,

VDD = VCC =VAHB = VBHB = 10V

-50 -25 -11 -60 -10 µA

AHB, BHB Operating Current IAHBO,

IBHBO

f = 500kHz, No Load 0.62 1.2 1.5 0.5 1.9 mA

AHS, BHS, AHB, BHB Leakage Current IHLK VBHS = VAHS = 80V,

VAHB = VBHB = 93V

- 0.02 1.0 - 10 µA

AHB-AHS, BHB-BHS Qpump

Output Voltage

VAHB -

VAHS

VBHB -

VBHS

IAHB = IAHB = 0, No Load 11.5 12.6 14.0 10.5 14.5 V

INPUT COMPARATOR PINS: IN+, IN-, OUT

Offset Voltage VOS Over Common Mode Voltage Range -10 0 +10 -15 +15 mV

Input Bias Current IIB 00.52 0 4 µA

Input Offset Current IOS -1 0 +1-2+2µA

Input Common Mode Voltage Range CMVR 1 - VDD

-1.5

HIP4080A

Voltage Gain AVOL 10 25 - 10 - V/mV

OUT High Level Output Voltage VOH IN+ > IN-, IOH = -250µAV

-0.4

--V

- 0.5

-V

OUT Low Level Output Voltage VOL IN+ < IN-, IOL = +250µA - -0.4-0.5V

Low Level Output Current IOL VOUT = 6V 6.5 14 19 6 20 mA

High Level Output Current IOH VOUT = 6V -17 -10 -3 -20 -2.5 mA

INPUT PINS: DIS

Low Level Input Voltage VIL Full Operating Conditions - - 1.0 - 0.8 V

High Level Input Voltage VIH Full Operating Conditions 2.5 - - 2.7 - V

Input Voltage Hysteresis -35- - -mV

Low Level Input Current IIL VIN = 0V, Full Operating Conditions -130 -100 -75 -135 -65 µA

High Level Input Current IIH VIN = 5V, Full Operating Conditions -1 - +1 -10 +10 µA

INPUT PINS: HEN

Low Level Input Voltage VIL Full Operating Conditions - - 1.0 - 0.8 V

High Level Input Voltage VIH Full Operating Conditions 2.5 - - 2.7 - V

Input Voltage Hysteresis -35- - -mV

Low Level Input Current IIL VIN = 0V, Full Operating Conditions -260 -200 -150 -270 -130 µA

High Level Input Current IIH VIN = 5V, Full Operating Conditions -1 - +1 -10 +10 µA

TURN-ON DELAY PINS: LDEL AND HDEL

LDEL, HDEL Voltage VHDEL,VI

HDEL = ILDEL = -100µA 4.9 5.1 5.3 4.8 5.4 V

GATE DRIVER OUTPUT PINS: ALO, BLO, AHO, AND BHO

Low Level Output Voltage VOL IOUT = 100mA 0.7 0.85 1.0 0.5 1.1 V

High Level Output Voltage VCC - VOH IOUT = -100mA 0.8 0.95 1.1 0.5 1.2 V

Peak Pullup Current IO+V

OUT = 0V 1.7 2.6 3.8 1.4 4.1 A

Peak Pulldown Current IO-V

OUT = 12V 1.7 2.4 3.3 1.3 3.6 A

Under Voltage, Rising Threshold UV+ 8.1 8.8 9.4 8.0 9.5 V

Under Voltage, Falling Threshold UV- 7.6 8.3 8.9 7.5 9.0 V

Under Voltage, Hysteresis HYS 0.25 0.4 0.65 0.2 0.7 V

Electrical Specifications VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100K, and

TA = +25°C, Unless Otherwise Specified (Continued)

PARAMETERS SYMBOL TEST CONDITIONS

TJ = +25°C

TJ = - 40°C

TO +125°C

UNITSMIN TYP MAX MIN MAX

HIP4080A

Switching Specifications VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 10K,

CL = 1000pF, and TA = +25°C, Unless Otherwise Specified

PARAMETERS SYMBOL TEST CONDITIONS

TJ = +25°C

TJ = - 40°C

TO +125°C

UNITSMIN TYP MAX MIN MAX

Lower Turn-off Propagation Delay (IN+/IN- to ALO/BLO) TLPHL - 40 70 - 90 ns

Upper Turn-off Propagation Delay (IN+/IN- to AHO/BHO) THPHL -5080-110ns

Lower Turn-on Propagation Delay (IN+/IN- to ALO/BLO) TLPLH - 40 70 - 90 ns

Upper Turn-on Propagation Delay (IN+/IN- to AHO/BHO) THPLH - 70 110 - 140 ns

Rise Time TR- 10 25 - 35 ns

Fall Time TF- 10 25 - 35 ns

Turn-on Input Pulse Width TPWIN-ON 50 - - 50 - ns

Turn-off Input Pulse Width TPWIN-OFF 40 - - 40 - ns

Disable Turn-off Propagation Delay

(DIS - Lower Outputs)

TDISLOW - 45 75 - 95 ns

Disable Turn-off Propagation Delay

(DIS - Upper Outputs)

TDISHIGH -5585-105ns

Disable to Lower Turn-on Propagation Delay

(DIS - ALO and BLO)

TDLPLH - 45 70 - 90 ns

Refresh Pulse Width (ALO and BLO) TREF-PW 240 380 500 200 600 ns

Disable to Upper Enable (DIS - AHO and BHO) TUEN - 480 630 - 750 ns

HEN-AHO, BHO Turn-off, Propagation Delay THEN-PHL RHDEL = RLDEL = 10K - 40 70 - 90 ns

HEN-AHO, BHO Turn-on, Propagation Delay THEN-PLH RHDEL = RLDEL = 10K - 60 90 - 110 ns

TRUTH TABLE

INPUT OUTPUT

IN+ > IN- HEN U/V DIS ALO AHO BLO BHO

X XX10000

0 0001000

1 1000110

0 1001001

1 0000010

X X1X0000

HIP4080A

Pin Descriptions

NUMBER SYMBOL DESCRIPTION

1 BHB B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap

diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30µA out of this pin to

maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.

2 HEN High-side Enable input. Logic level input that when low overrides IN+/IN- (Pins 6 and 7) to put AHO and BHO drivers

(Pins 11 and 20) in low output state. When HEN is high AHO and BHO are controlled by IN+/IN- inputs. The pin can

be driven by signal levels of 0V to 15V (no greater than VDD).

3 DIS DISable input. Logic level input that when taken high sets all four outputs low. DIS high overrides all other inputs.

When DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of 0V to

15V (no greater than VDD).

SS Chip negative supply, generally will be ground.

5 OUT OUTput of the input control comparator. This output can be used for feedback and hysteresis.

6 IN+ Noninverting input of control comparator. If IN+ is greater than IN- (Pin 7) then ALO and BHO are low level outputs

and BLO and AHO are high level outputs. If IN+ is less than IN- then ALO and BHO are high level outputs and BLO

and AHO are low level outputs. DIS (Pin 3) high level will override IN+/IN- control for all outputs. HEN (Pin 2) low level

will override IN+/IN- control of AHO and BHO. When switching in four quadrant mode, dead time in a half bridge leg

is controlled by HDEL and LDEL (Pins 8 and 9).

7 IN- Inverting input of control comparator. See IN+ (Pin 6) description.

8 HDEL High-side turn-on DELay. Connect resistor from this pin to VSS to set timing current that defines the turn-on delay of

both high-side drivers. The low-side drivers turn-off with no adjustable delay, so the HDEL resistor guarantees no

shoot-through by delaying the turn-on of the high-side drivers. HDEL reference voltage is approximately 5.1V.

9 LDEL Low-side turn-on DELay. Connect resistor from this pin to VSS to set timing current that defines the turn-on delay of

both low-side drivers. The high-side drivers turn-off with no adjustable delay, so the LDEL resistor guarantees no

shoot-through by delaying the turn-on of the low-side drivers. LDEL reference voltage is approximately 5.1V.

10 AHB A High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap

diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30µA out of this pin to

maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.

11 AHO A High-side Output. Connect to gate of A High-side power MOSFET.

12 AHS A High-side Source connection. Connect to source of A High-side power MOSFET. Connect negative side of

bootstrap capacitor to this pin.

13 ALO A Low-side Output. Connect to gate of A Low-side power MOSFET.

14 ALS A Low-side Source connection. Connect to source of A Low-side power MOSFET.

15 VCC Positive supply to gate drivers. Must be same potential as VDD (Pin 16). Connect to anodes of two bootstrap diodes.

16 VDD Positive supply to lower gate drivers. Must be same potential as VCC (Pin 15). De-couple this pin to VSS (Pin 4).

17 BLS B Low-side Source connection. Connect to source of B Low-side power MOSFET.

18 BLO B Low-side Output. Connect to gate of B Low-side power MOSFET.

19 BHS B High-side Source connection. Connect to source of B High-side power MOSFET. Connect negative side of

bootstrap capacitor to this pin.

20 BHO B High-side Output. Connect to gate of B High-side power MOSFET.

HIP4080A

Timing Diagrams

FIGURE 1. BISTATE MODE

FIGURE 2. HIGH SIDE CHOP MODE

FIGURE 3. DISABLE FUNCTION

HEN

ALO

AHO

BLO

TLPHL THPLH

(10% - 90%)

(90% - 10%)

TDT

U/V = DIS

THPHL TLPLH

TDT

IN+ > IN-

BHO

HEN

ALO

AHO

BLO

U/V = DIS

THEN-PLH

THEN-PHL

IN+ > IN-

BHO

HEN

AHO

BLO

U/V or DIS

TREF-PW

TDLPLH

IN+ > IN-

BHO

TDIS

TUEN

ALO

HIP4080A

Typical Performance Curves VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =

100K, and TA = +25°C, Unless Otherwise Specified

FIGURE 4. QUIESCENT IDD SUPPLY CURRENT vs VDD

SUPPLY VOLTAGE

FIGURE 5. IDDO NO-LOAD IDD SUPPLY CURRENT vs

FREQUENCY (kHz)

FIGURE 6. SIDE A, B FLOATING SUPPLY BIAS CURRENT vs

FREQUENCY (LOAD = 1000pF)

FIGURE 7. ICCO, NO-LOAD ICC SUPPLY CURRENT vs

FREQUENCY (kHz) TEMPERATURE

FIGURE 8. IAHB, IBHB NO-LOAD FLOATING SUPPLY BIAS

CURRENT vs FREQUENCY

FIGURE 9. COMPARATOR INPUT CURRENT IL vs

TEMPERATURE AT VCM = 5V

810 12 14

2.0

4.0

6.0

8.0

10.0

12.0

14.0

IDD SUPPLY CURRENT (mA)

VDD SUPPLY VOLTAGE (V)

12.5

12.0

11.5

11.0

10.5

10 200 400 600 800 1000

IDD SUPPLY CURRENT (mA)

SWITCHING FREQUENCY (kHz)

0100 200 300 400 500 600 700 800 900 1000

0.0

5.0

10.0

15.0

20.0

FLOATING SUPPLY BIAS CURRENT (mA)

SWITCHING FREQUENCY (kHz)

0 100 200 300 400 500 600 700 800 900 1000

0.0

1.0

2.0

3.0

4.0

5.0

ICC SUPPLY CURRENT (mA)

SWITCHING FREQUENCY (kHz)

+75°C

+25°C

+125°C

-40°C

0°C

0.5

1.5

2.5

200

600 800 1000

0 400

FLOATING SUPPLY BIAS CURRENT (mA)

SWITCHING FREQUENCY (kHz)

-40 -20 020 40 60 80 100 120

0.5

1.0

COMPARATOR INPUT CURRENT (µA)

JUNCTION TEMPERATURE (°C)

HIP4080A

FIGURE 10. DIS LOW LEVEL INPUT CURRENT IIL vs

TEMPERATURE

FIGURE 11. HEN LOW LEVEL INPUT CURRENT IIL vs

TEMPERATURE

FIGURE 12. AHB - AHS, BHB - BHS NO-LOAD CHARGE PUMP

VOLTAGE vs TEMPERATURE

FIGURE 13. UPPER DISABLE TURN-OFF PROPAGATION

DELAY TDISHIGH vs TEMPERATURE

FIGURE 14. DISABLE TO UPPER ENABLE TUEN

PROPAGATION DELAY vs TEMPERATURE

FIGURE 15. LOWER DISABLE TURN-OFF PROPAGATION

DELAY TDISLOW vs TEMPERATURE

Typical Performance Curves VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =

100K, and TA = +25°C, Unless Otherwise Specified (Continued)

-50 -25 025 50 75 100 125

-120

-110

-100

-90

LOW LEVEL INPUT CURRENT (µA)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

-230

-220

-210

-200

-190

-180

LOW LEVEL INPUT CURRENT (µA)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

10.0

11.0

12.0

13.0

14.0

15.0

NO-LOAD FLOATING CHARGE PUMP VOLTAGE (V)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

425

450

475

500

525

-50 -25 025 50 75 100 125 150

JUNCTION TEMPERATURE (°C)

PROPAGATION DELAY (ns)

-40 -20 020 40 60 80 100 120

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

HIP4080A

Typical Performance Curves VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =

10K, and TA = +25°C, Unless Otherwise Specified

FIGURE 16. TREF-PW REFRESH PULSE WIDTH vs

TEMPERATURE

FIGURE 17. DISABLE TO LOWER ENABLE TDLPLH

PROPAGATION DELAY vs TEMPERATURE

FIGURE 18. UPPER TURN-OFF PROPAGATION DELAY THPHL

vs TEMPERATURE

FIGURE 19. UPPER TURN-ON PROPAGATION DELAY THPLH

vs TEMPERATURE

FIGURE 20. LOWER TURN-OFF PROPAGATION DELAY TLPHL

vs TEMPERATURE

FIGURE 21. LOWER TURN-ON PROPAGATION DELAY TLPLH

vs TEMPERATURE

350

375

400

425

450

-50 -25 025 50 75 100 125 150

REFRESH PULSE WIDTH (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

40.0

50.0

60.0

70.0

80.0

90.0

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

40.0

50.0

60.0

70.0

80.0

90.0

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

40.0

50.0

60.0

70.0

80.0

90.0

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

40.0

50.0

60.0

70.0

80.0

90.0

PROPAGATION DELAY (ns)

JUNCTION TEMPERATURE (°C)

HIP4080A

Typical Performance Curves VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =

100K, and TA = +25°C, Unless Otherwise Specified

FIGURE 22. GATE DRIVE FALL TIME TF vs TEMPERATURE FIGURE 23. GATE DRIVE RISE TIME TR vs TEMPERATURE

FIGURE 24. VLDEL, VHDEL VOLTAGE vs TEMPERATURE FIGURE 25. HIGH LEVEL OUTPUT VOLTAGE, VCC - VOH vs

BIAS SUPPLY AND TEMPERATURE AT 100µA

FIGURE 26. LOW LEVEL OUTPUT VOLTAGE VOL vs BIAS

SUPPLY AND TEMPERATURE AT 100µA

FIGURE 27. PEAK PULLDOWN CURRENT IO- BIAS SUPPLY

VOLTAGE

-40 -20 020 40 60 80 100 120

8.5

9.5

10.5

11.5

12.5

GATE DRIVE FALL TIME (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

8.5

9.5

10.5

11.5

12.5

13.5

TURN-ON RISE TIME (ns)

JUNCTION TEMPERATURE (°C)

-40 -20 020 40 60 80 100 120

4.0

4.5

5.0

5.5

6.0

HDEL, LDEL INPUT VOLTAGE (V)

JUNCTION TEMPERATURE (°C)

10 12 14

250

500

750

1000

1250

1500

VCC - VOH (mV)

BIAS SUPPLY VOLTAGE (V)

+75°C

+25°C

+125°C

-40°C

0°C

12 14

250

500

750

1000

1250

1500

VOL (mV)

BIAS SUPPLY VOLTAGE (V)

+75°C

+25°C

+125°C

-40°C

0°C

6 7 8 9 10 11 12 13 14 15 16

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

GATE DRIVE SINK CURRENT (A)

VCC, VDD, VAHG, VBHB (V)

HIP4080A

FIGURE 28. PEAK PULLUP CURRENT IO+ vs SUPPLY

VOLTAGE

FIGURE 29. LOW VOLTAGE BIAS CURRENT IDD AND ICC

(LESS QUIESCENT COMPONENT) vs

FREQUENCY AND GATE LOAD CAPACITANCE

FIGURE 30. HIGH VOLTAGE LEVEL-SHIFT CURRENT vs

FREQUENCY AND BUS VOLTAGE

FIGURE 31. UNDERVOLTAGE LOCKOUT vs TEMPERATURE

FIGURE 32. MINIMUM DEAD-TIME vs DEL RESISTANCE

Typical Performance Curves VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =

100K, and TA = +25°C, Unless Otherwise Specified (Continued)

6 7 8 9 10 11 12 13 14 15 16

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

GATE DRIVE SINK CURRENT (A)

VCC, VDD, VABH, VBHB (V)

110 100 10002 5 20 50 500200

0.1

100

500

0.5

200

0.2

LOW VOLTAGE BIAS CURRENT (mA)

SWITCHING FREQUENCY (kHz)

3,000

1,000

10,000

100

10 100 100020 50 200 500

100

1000

200

500

LEVEL-SHIFT CURRENT (µA)

SWITCHING FREQUENCY (kHz)

8.2

8.4

8.6

8.8

50 25 025 50 75 100 125 150

UV+

UV-

TEMPERATURE (°C)

BIAS SUPPLY VOLTAGE, VDD (V)

10 50 100 150 200 250

120

150

HDEL/LDEL RESISTANCE (kΩ)

DEAD-TIME (ns)

HIP4080A

10 11

R21 Q1

R22

R23 C1

JMPR1

R24

R30 R31

R34

CR2

CR1

JMPR5

JMPR3

JMPR2

JMPR4

R33

CX CY

CW CW

B+

IN2 IN1

OUT/BLI

IN-/AHI

COM

IN+/ALI +12V

+12V

BLS

HEN/BHI

ALS

CD4069UB

HIP4080A/81A

SECTION

CONTROL LOGIC

POWER SECTION

DRIVER SECTION

AHOAHB

AHSLDEL

ALOHDEL

ALSIN-/AHI

VCC

IN+/ALI

VDD

OUT/BLI

BLSVSS

BLODIS

BHSHEN/BHI

BHOBHB

R29

NOTES:

1. DEVICE CD4069UB PIN 7 = COM. PIN 14 = +12V.

2. COMPONENTS L1, L2, C1, C2, CX, CY, R30, R31, ARE NOT

SUPPLIED. REFER TO APPLICATION NOTE FOR HELP IN

DETERMINING JMPR1 - JMPR4 JUMPER LOCATIONS.

FIGURE 33. HIP4080A EVALUATION PC BOARD SCHEMATIC

HIP4080A

R22 1

JMPR2

JMPR5

R31

R33

CR2

R23

R24

R27

R28

R26

JMPR3

R21

GND

JMPR4

JMPR1

R30

CR1

R34

R32

R29

COM

+12V B+

IN1

IN2

AHO

BHO

ALO

BLO

BLS

LDEL

HDEL

DIS

ALS

HIP4080/81

FIGURE 33. HIP4080A EVALUATION BOARD SILKSCREEN

HIP4080A

Dual-In-Line Plastic Packages (PDIP)

NOTES:

1. Controlling Dimensions: INCH. In case of conflict between English

and Metric dimensions, the inch dimensions control.

2. Dimensioning and tolerancing per ANSI Y14.5M-1982.

3. Symbols are defined in the “MO Series Symbol List” in Section 2.2

of Publication No. 95.

4. Dimensions A, A1 and L are measured with the package seated in

JEDEC seating plane gauge GS-3.

5. D, D1, and E1 dimensions do not include mold flash or protrusions.

Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).

6. E and are measured with the leads constrained to be perpen-

dicular to datum .

7. eB and eC are measured at the lead tips with the leads uncon-

strained. eC must be zero or greater.

8. B1 maximum dimensions do not include dambar protrusions. Dam-

bar protrusions shall not exceed 0.010 inch (0.25mm).

9. N is the maximum number of terminal positions.

10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,

E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).

eA-C-

-B-

INDEX 12 3 N/2

AREA

SEATING

BASE

PLANE

-C-

B1 Be

-A-

0.010 (0.25) C AMBS

E20.3 (JEDEC MS-001-AD ISSUE D)

20 LEAD DUAL-IN-LINE PLASTIC PACKAGE

SYMBOL

INCHES MILLIMETERS

NOTESMIN MAX MIN MAX

A - 0.210 - 5.33 4

A1 0.015 - 0.39 - 4

A2 0.115 0.195 2.93 4.95 -

B 0.014 0.022 0.356 0.558 -

B1 0.045 0.070 1.55 1.77 8

C 0.008 0.014 0.204 0.355 -

D 0.980 1.060 24.89 26.9 5

D1 0.005 - 0.13 - 5

E 0.300 0.325 7.62 8.25 6

E1 0.240 0.280 6.10 7.11 5

e 0.100 BSC 2.54 BSC -

eA0.300 BSC 7.62 BSC 6

eB- 0.430 - 10.92 7

L 0.115 0.150 2.93 3.81 4

N20 209

Rev. 0 12/93

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.

Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without

notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and

reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result

from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

HIP4080A

Small Outline Plastic Packages (SOIC)

NOTES:

1. Symbols are defined in the “MO Series Symbol List” in Section

2.2 of Publication Number 95.

2. Dimensioning and tolerancing per ANSI Y14.5M-1982.

3. Dimension “D” does not include mold flash, protrusions or gate

burrs. Mold flash, protrusion and gate burrs shall not exceed

0.15mm (0.006 inch) per side.

4. Dimension “E” does not include interlead flash or protrusions. In-

terlead flash and protrusions shall not exceed 0.25mm (0.010

inch) per side.

5. The chamfer on the body is optional. If it is not present, a visual

index feature must be located within the crosshatched area.

6. “L” is the length of terminal for soldering to a substrate.

7. “N” is the number of terminal positions.

8. Terminal numbers are shown for reference only.

9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater

above the seating plane, shall not exceed a maximum value of

0.61mm (0.024 inch)

10. Controlling dimension: MILLIMETER. Converted inch dimen-

sions are not necessarily exact.

INDEX

AREA E

123

-B-

0.25(0.010) C A

MBS

-A-

-C-

SEATING PLANE

0.10(0.004)

h x 45o

0.25(0.010) B

M20.3 (JEDEC MS-013-AC ISSUE C)

20 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE

SYMBOL

INCHES MILLIMETERS

NOTESMIN MAX MIN MAX

A 0.0926 0.1043 2.35 2.65 -

A1 0.0040 0.0118 0.10 0.30 -

B 0.014 0.019 0.35 0.49 9

C 0.0091 0.0125 0.23 0.32 -

D 0.4961 0.5118 12.60 13.00 3

E 0.2914 0.2992 7.40 7.60 4

e 0.050 BSC 1.27 BSC -

H 0.394 0.419 10.00 10.65 -

h 0.010 0.029 0.25 0.75 5

L 0.016 0.050 0.40 1.27 6

N20 207

α0o8o0o8o-

Rev. 1 1/02