APS13290 and APS13291 Precision Hall-Effect Latches for Consumer and Industrial Applications FEATURES AND BENEFITS * * * * * * * * * * * * Symmetrical latch switchpoints Superior ruggedness and fault tolerance Reverse-polarity and transient protection Operation from -40C to 175C junction temperature Output short-circuit and overvoltage protection Superior temperature stability Resistant to physical stress High EMC immunity, 12 kV HBM ESD Operation from unregulated supplies, 2.8 to 24 V Chopper stabilization Solid-state reliability Industry-standard packages and pinouts PACKAGES: Not to scale 3-pin SIP (suffix UA) 3-pin SOT23W (suffix LH) DESCRIPTION The APS13290 and APS13291 are three-wire, planar Hall-effect sensor integrated circuits (ICs) especially suited for operation over extended temperature ranges (up to 125C). This family of precision Hall-effect latch ICs are ideal for industrial and consumer applications and feature performance enhancements permitting high-temperature operation up to 175C junction temperatures. In addition, the APS13290/1 include a number of features designed specifically to maximize system robustness, such as reverse-polarity protection, output current limiter, overvoltage, and EMC protection. The single silicon chip includes: a voltage regulator, a Hall plate, small signal amplifier, chopper stabilization, Schmitt trigger, and a short-circuit-protected open-drain output. A south pole of sufficient strength turns the output on; a north pole of sufficient strength is necessary to turn the output off. The devices include on-board transient protection for all pins, permitting operation directly from a vehicle battery or regulator with supply voltages from 2.8 to 24 V. Two package styles provide a choice of through-hole or surface mounting. Package type LH is a modified 3-pin SOT23W surface-mount package, while UA is a three-pin ultramini SIP for through-hole mounting. Both packages are lead (Pb) free and RoHS compliant, with 100% matte-tin-plated leadframes. Functional Block Diagram VCC REGULATOR Hall Element DYNAMIC OFFSET CANCELLATION TO ALL SUBCIRCUITS LOW-PASS FILTER HALL AMP. SAMPLE, HOLD & AVERAGING SCHMITT TRIGGER VOUT CONTROL CURRENT LIMIT GND APS13290-1-DS, Rev. 1 MCO-0000385 February 11, 2019 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 SELECTION GUIDE Magnetic Switchpoints [2] Part Number Packing [1] Mounting APS13290KLHALX 13-in. reel, 10000 pieces/reel 3-pin SOT23W surface mount APS13290KLHALT [3] 7-in. reel, 3000 pieces/reel 3-pin SOT23W surface mount APS13290KUAA Bulk, 500 pieces/bag 3-pin SIP through hole APS13291KLHALX 13-in. reel, 10000 pieces/reel 3-pin SOT23W surface mount APS13291KLHALT [3] 7-in. reel, 3000 pieces/reel 3-pin SOT23W surface mount APS13291KUAA Bulk, 500 pieces/bag 3-pin SIP through hole Operate BOP (G) Release BRP (G) 5 to 40 -5 to -40 Ambient Temperature, TA -40C to 125C 25 to 80 -25 to -80 [1] Contact Allegro for additional packing options. convention used: (+) south polarity, () north polarity. [3] Available through authorized Allegro distributors only. [2] Algebraic RoHS COMPLIANT VSUPPLY RLOAD = 1 k APS1329x 1 CBYP = 0.1 F VCC VOUT 2 VOUT GND 3 Figure 1: Typical Application Circuit Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 2 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 ABSOLUTE MAXIMUM RATINGS Characteristic Forward Supply Voltage Symbol Notes Rating Units VCC 30 V Reverse Supply Voltage [1] VRCC -18 V Output Off Voltage [1] VOUT 30 V Output Current [2] IOUT 60 mA mA [1] Reverse Output Current IROUT -50 Magnetic Flux Density [3] B Unlimited - Operating Temperature Range TA -40 to 125 C Maximum Junction Temperature TJ(max) Storage Temperature Range K For 500 hours Tstg ESD Voltage 165 C 175 C -65 to 170 C VESD(HBM) Human Body Model according to AEC-Q100-002 12 kV VESD(CDM) Charged Device Model according to AEC-Q100-011 1 kV [1] This rating does not apply to extremely short voltage transients such as load dump and/or ESD. Those events have individual ratings, specific to the respective transient voltage event. [2] Through short-circuit current limiting device. [3] Guaranteed by design. GND PINOUT DIAGRAMS AND TERMINAL LIST TABLE 3 3 VOUT 2 GND VOUT VCC 2 VCC 1 1 Package UA Package LH Terminal List Name Description Number Package LH Package UA Connects power supply to chip 1 1 VOUT Output from circuit 2 3 GND Ground 3 2 VCC Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 3 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 ELECTRICAL CHARACTERISTICS: Valid over full operating voltage, ambient temperature range TA = -40C to 125C, and with CBYP = 0.1 F (unless otherwise specified) Characteristics Symbol Test Conditions Min. Typ. [1] Max. Unit [2] 2.8 - 24 V mA ELECTRICAL CHARACTERISTICS Forward Supply Voltage Supply Current Output Leakage Current VCC ICC IOUTOFF Output Saturation Voltage VOUT(SAT) Output Off Voltage VOUTOFF Power-On Time [3] Power-On State, Output [3] Operating, TJ < 175C tON POS 1 2 3 VOUTOFF = 24 V, B < BRP - - 10 A IOUT = 20 mA, B > BOP - 200 500 mV B < BRP - - 24 V VCC VCC(min), B < BRP(min) - 10 G, B > BOP(max) + 10 G - - 25 s VCC VCC(min), t < tON Low - Chopping Frequency fC - 800 - kHz Output Rise Time [4] tr RLOAD = 1 k, CL = 20 pF - 0.2 2 s Output Fall Time [4] tf RLOAD = 1 k, CL = 20 pF - 0.1 2 s 30 - 60 mA TRANSIENT PROTECTION CHARACTERISTICS Output Short-Circuit Current Limit Output Zener Clamp Voltage Reverse Battery Current Supply Zener Clamp Voltage IOM VZoutput IRCC VZ IOUT = 3 mA, TA = 25C, Output Off 30 - - V VRCC = -18 V, TA = 25C - - -5 mA ICC = ICC(max) + 3 mA, TA = 25C 30 - - V APS13290 5 20 40 G MAGNETIC CHARACTERISTICS Operate Point Release Point BOP BRP APS13291 25 50 80 G APS13290 -40 -20 -5 G APS13291 -80 -50 -25 G APS13290 10 40 80 G Hysteresis BHYS APS13291 50 100 160 G Symmetry BSYM BOP + BRP -27.5 - 27.5 G Magnetic Offset BOFF (BOP + BRP) / 2 -13.75 - 13.75 G [1] Typical data are at TA = 25C and VCC = 12 V. G (gauss) = 0.1 mT (millitesla). [3] Guaranteed by device design and characterization. [4] C = oscilloscope probe capacitance. L [2] 1 Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 4 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 THERMAL CHARACTERISTICS: May require derating at maximum conditions; see application information Characteristic Symbol Test Conditions RJA Package Thermal Resistance Value Units Package LH, 1-layer PCB with copper limited to solder pads 228 C/W Package LH, 2-layer PCB with 0.463 in.2 of copper area each side connected by thermal vias 110 C/W Package UA, 1-layer PCB with copper limited to solder pads 165 C/W Power Derating Curve Maximum Allowable VCC (V) TJ(max) = 175C; ICC = ICC(max), IOUT = 0 mA (Output Off) 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 VCC(max) Package LH, 2-layer PCB (RJA = 110 C/W) Package UA, 1-layer PCB (RJA = 165 C/W) Package LH, 1-layer PCB (RJA = 228 C/W) VCC(min) 25 45 65 85 105 125 145 Temperature (C) 165 185 TJ(max) Power Dissipation, PD (mW) Power Dissipation versus Ambient Temperature 1900 1800 1700 1600 1500 1400 1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 0 Package LH, 2-layer PCB (RJA = 110C/W) Package UA, 1-layer PCB (RJA = 165C/W) Package LH, 1-layer PCB (RJA = 228C/W) 25 45 65 85 105 125 145 165 185 Temperature (C) Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 5 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 CHARACTERISTIC PERFORMANCE DATA Electrical Characteristics Average Supply Current versus Supply Voltage Average Supply Current versus Ambient Temperature 4.0 4.0 3.5 3.5 TA (C) 2.5 -40 2.0 25 1.5 3.0 ICC (mA) ICC (mA) 3.0 125 1.0 12 1.5 24 0.5 2 6 10 14 VCC (V) 18 22 0.0 26 TA (C) TA (C) -40 -40 25 25 125 125 6 6 10 10 14 VCC14(V) VCC (V) 18 18 22 22 26 26 VOUT(SAT) (mV) VOUT(SAT) (mV) 500 500 450 450 400 400 350 350 300 300 250 250 200 200 150 150 100 100 50 50 0 0 2 2 -60 -40 -20 0 20 40 TA (C) 60 80 100 120 140 Average Low Output Voltage versus Ambient Temperature for IOUT = 20 mA Average Low Output Voltage versus Ambient Temperature for IOUT = 20 mA Average Low Output Voltage versus Supply Voltage for IOUT = 20 mA Average Low Output Voltage versus Supply Voltage for IOUT = 20 mA VOUT(SAT) (mV) VOUT(SAT) (mV) 2.8 2.0 1.0 0.5 0.0 VCC (V) 2.5 500 500 450 450 400 400 350 350 300 300 250 250 200 200 150 150 100 100 50 50 0 0 -60 -60 VCC (V) VCC (V) 2.8 2.8 12 12 24 24 -40 -40 -20 -20 0 0 20 20 40 TA 40 (C) TA (C) 60 60 80 80 100 100 120 120 Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 140 140 6 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 CHARACTERISTIC PERFORMANCE DATA (continued) APS13290 Magnetic Characteristics Average Operate Point versus Ambient Temperature Average Operate Point versus Supply Voltage 40 40 35 35 TA (C) -40 25 20 25 15 125 30 BOP (G) BOP (G) 30 2.8 20 12 15 24 10 10 5 VCC (V) 25 5 2 6 10 14 VCC (V) 18 22 26 -60 -5 -20 -25 25 -30 125 60 80 100 120 140 VCC (V) -20 2.8 -25 12 -30 24 -35 -40 2 6 10 14 VCC (V) 18 22 26 -60 Average Switchpoint Hysteresis versus Supply Voltage -40 -20 0 20 40 TA (C) 60 80 100 120 140 Average Switchpoint Hysteresis versus Ambient Temperature 80 80 70 70 60 TA (C) 50 -40 40 25 30 125 VCC (V) 60 BHYS (G) BHYS (G) 40 TA (C) -15 BRP (G) BRP (G) -40 -35 2.8 50 12 40 24 30 20 20 10 2 6 10 14 VCC (V) 18 22 26 -60 Average BOP + BRP Symmetry versus Supply Voltage -40 -20 0 20 40 TA (C) 60 80 100 120 140 Average BOP + BRP Symmetry versus Ambient Temperature 25 25 20 20 10 TA (C) 5 -40 0 -5 25 -10 125 -15 BSYM (G) 15 15 BSYM (G) 20 -10 TA (C) -15 VCC (V) 10 5 2.8 0 12 -5 24 -10 -15 -20 -20 -25 0 -5 -10 10 -20 Average Release Point versus Ambient Temperature Average Release Point versus Supply Voltage -40 -40 -25 2 6 10 14 VCC (V) 18 22 26 -60 -40 -20 0 20 40 TA (C) 60 80 100 120 140 Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 7 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 CHARACTERISTIC PERFORMANCE DATA (continued) APS13291 Magnetic Characteristics Average Operate Point versus Ambient Temperature TA (C) -40 25 BOP (G) BOP (G) Average Operate Point versus Supply Voltage 90 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 125 2 6 10 14 VCC (V) 18 22 90 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 26 VCC (V) 2.8 12 24 -60 -40 25 BRP (G) BRP (G) TA (C) 125 2 6 10 14 VCC (V) 18 22 -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 -85 -90 26 BHYS (G) BHYS (G) -40 25 125 6 10 14 VCC (V) 18 22 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 26 60 80 100 120 140 12 24 -60 -40 -20 0 20 40 TA (C) 60 80 100 120 140 VCC (V) 2.8 12 24 -60 -40 -20 0 20 40 TA (C) 60 80 100 120 140 Average BOP + BRP Symmetry versus Ambient Temperature 25 20 20 TA (C) 10 5 -40 0 -5 25 -10 125 -15 BSYM (G) 15 15 BSYM (G) 40 TA (C) 2.8 Average BOP + BRP Symmetry versus Supply Voltage 25 VCC (V) 10 5 2.8 0 12 -5 24 -10 -15 -20 -20 -25 20 Average Switchpoint Hysteresis versus Ambient Temperature TA (C) 2 0 VCC (V) Average Switchpoint Hysteresis versus Supply Voltage 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 -20 Average Release Point versus Ambient Temperature Average Release Point versus Supply Voltage -15 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 -85 -90 -40 -25 2 6 10 14 VCC (V) 18 22 26 -60 -40 -20 0 20 40 TA (C) 60 80 100 120 140 Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 8 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 FUNCTIONAL DESCRIPTION OPERATION The output of these devices switches low (turns on) when a magnetic field perpendicular to the Hall element exceeds the operate point threshold, BOP (see Figure 2). After turn-on, the output voltage is VOUT(SAT) . The output transistor is capable of continuously sinking up to 30 mA. When the magnetic field is reduced below the release point, BRP , the device output goes high (turns off) to VOUTOFF. The difference in the magnetic operate and release points is the hysteresis, BHYS , of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. POWER-ON BEHAVIOR Device power-on occurs once tON has elapsed. During the time prior to tON, and after VCC VCC(min), the output state is VOUT(SAT) (Low). After tON has elapsed, the output will correspond with the applied magnetic field for B > BOP or B < BRP. See Figure 3 for an example. Powering-on the device in the hysteresis range (less than BOP and higher than BRP) will give an output state of VOUT(SAT). The correct state is attained after the first excursion beyond BOP or BRP . POS Removal of the magnetic field will leave the device output latched on if the last crossed switchpoint is BOP, or latched off if the last crossed switch point is BRP. B > BOP, BRP < B < BOP V B < BRP VOUTOFF VOUT 0 BOP B- VOUT Output State Undefined for VCC< VCC(min) POS VOUT(SAT ) t V VOUT(SAT) BRP 0 Switch to Low Switch to High VOUTOFF B+ BHYS VCC V+ VCC (min) 0 t ON t Figure 3: Power-On Timing Diagram Figure 2: Switching Behavior of Latches On the horizontal axis, the B+ direction indicates increasing south polarity magnetic field strength, and the B- direction indicates increasing north polarity field strength. Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 9 APS13290 and APS13291 Precision Hall-Effect Latches for Consumer and Industrial Applications APPLICATIONS VPULL-UP VSUPPLY It is strongly recommended that an external bypass capacitor be connected (in close proximity to the Hall element) between the supply and ground of the device to guarantee correct performance under harsh environmental conditions and to reduce noise from internal circuitry. As is shown in Figure 1: Typical Application Circuit, a 0.1 F capacitor is typical. In applications where maximum robustness is required, such as long-life industrial motors, additional measures may be taken. In Figure 4: Enhanced Protection Circuit, a resistor in series with the VCC pin and a capacitor on the VOUT pin enhance the EMC immunity of the device. It is up to the user to fully qualify the Allegro sensor IC in their end system to ensure they achieve their system requirements. RLOAD = 1 k A RS = 100 APS1329x 1 VCC VOUT VOUT 2 A CBYP = 0.1 F A GND 3 COUT = 4.7 nF RS and C OUT are recommended for maximum robustness in an automotive environment. Figure 4: Enhanced Protection Circuit These devices are sensitive in the direction perpendicular to the branded face, as depicted in Figure 5. For further information, extensive applications information on magnets and Hall-effect sensors is available in: * Hall-Effect IC Applications Guide, AN27701, * Hall-Effect Devices: Guidelines for Designing Subassemblies Using Hall-Effect Devices AN27703.1 * Soldering Methods for Allegro's Products - SMD and Through-Hole, AN26009 All are provided on the Allegro website: www.allegromicro.com Figure 5: Sensing Configurations Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 10 APS13290 and APS13291 Precision Hall-Effect Latches for Consumer and Industrial Applications CHOPPER STABILIZATION A limiting factor for switchpoint accuracy when using Hall-effect technology is the small signal voltage developed across the Hall plate. This voltage is proportionally small relative to the offset that can be produced at the output of the Hall sensor. This makes it difficult to process the signal and maintain an accurate, reliable output over the specified temperature and voltage range. Chopper stabilization is a proven approach used to minimize Hall offset. The Allegro technique, dynamic quadrature offset cancellation, removes key sources of the output drift induced by temperature and package stress. This offset reduction technique is based on a signal modulation-demodulation process. Figure 6 illustrates how it is implemented. The undesired offset signal is separated from the magnetically induced signal in the frequency domain through modulation. The subsequent demodulation acts as a modulation process for the offset, causing the magnetically induced signal to recover its original spectrum at baseband while the DC offset becomes a high-frequency signal. Then, using a low-pass filter, the signal passes while the modulated DC offset is suppressed. Allegro's innovative chopper stabilization technique uses a high-frequency clock. The high-frequency operation allows a greater sampling rate that produces higher accuracy, reduced jitter, and faster signal processing. Additionally, filtering is more effective and results in a lower noise analog signal at the sensor output. Devices such as the APS13290 and APS13291 that use this approach have an extremely stable quiescent Hall output voltage, are immune to thermal stress, and have precise recoverability after temperature cycling. This technique is made possible through the use of a BiCMOS process which allows the use of low offset and low noise amplifiers in combination with high-density logic and sample-and-hold circuits. Regulator Hall Element Amp Sample and Hold Clock/Logic Low-Pass Filter Figure 6: Model of Chopper Stabilization (Dynamic Offset Cancellation) Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 11 APS13290 and APS13291 Precision Hall-Effect Latches for Consumer and Industrial Applications POWER DERATING The device must be operated below the maximum junction temperature of the device, TJ(max). Under certain combinations of peak conditions, reliable operation may require derating supplied power or improving the heat dissipation properties of the application. This section presents a procedure for correlating factors affecting operating TJ. (Thermal data is also available on the Allegro MicroSystems website.) The Package Thermal Resistance, RJA, is a figure of merit summarizing the ability of the application and the device to dissipate heat from the junction (die), through all paths to the ambient air. Its primary component is the Effective Thermal Conductivity, K, of the printed circuit board, including adjacent devices and traces. Radiation from the die through the device case, RJC, is a relatively small component of RJA. Ambient air temperature, TA, and air motion are significant external factors, damped by overmolding. The resulting power dissipation capability directly reflects upon the ability of the device to withstand extreme operating conditions. The junction temperature mission profile specified in the Absolute Maximum Ratings table designates a total operating life capability based on qualification for the most extreme conditions, where TJ may reach 175C. The silicon IC is heated internally when current is flowing into the VCC terminal. When the output is on, current sinking into the VOUT terminal generates additional heat. This may increase the junction temperature, TJ, above the surrounding ambient temperature. The APS13290 and APS13291 are permitted to operate up to TJ = 175C. As mentioned above, an operating device will increase TJ according to equations 1, 2, and 3 below. This allows an estimation of the maximum ambient operating temperature. For example, given common conditions such as: TA= 25C, VCC = 12 V, ICC = 2 mA, VOUT = 200 mV, IOUT = 20 mA (output on), and RJA = 165C/W, then: PD = (VCC x ICC) + (VOUT x IOUT) = (12 V x 2 mA) + (200 mV x 20 mA) = 24 mW + 4 mW = 28 mW T = PD x RJA = 28 mW x 165C/W = 4.6C TJ = TA + T = 25C + 4.6C = 29.6C A worst-case estimate, PD(max), represents the maximum allowable power level (VCC(max), ICC(max)), without exceeding TJ(max), at a selected RJA. For example, given the conditions RJA = 228C/W, TJ(max) = 175C, VCC(max) = 24 V, ICC(max) = 3.25 mA, VOUT = 500 mV, and IOUT = 30 mA (output on), the maximum allowable operating ambient temperature can be determined. The power dissipation required for the output is shown below: PD(VOUT) = VOUT x IOUT = 500 mV x 30 mA = 15 mW The power dissipation required for the IC supply is shown below: PD(VCC) = VCC x ICC = 24 V x 3.25 mA = 78 mW Next, by inverting using equation 2: T = PD x RJA = [PD(VOUT) + PD(VCC)] x 228C/W = (15 mW + 78 mW) x 228C/W = 93 mW x 228C/W = 21.2C Finally, by inverting equation 3 with respect to voltage: TA(est) = TJ(max) - T = 175C - 21.2C = 153.8C (1) In the above case, there is sufficient power dissipation capability to operate up to TA(est). The example indicates that TA(max) T = PD x RJA (2) can be as high as 153.8C without exceeding TJ(max). However, the TA(max) rating of the devices is 125C; the APS13290 and TJ = TA + T(3) APS13291 performance is not guaranteed above TA = 125C. PD = VIN x IIN Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 12 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 Package LH, 3-Pin (SOT-23W) +0.12 2.98 -0.08 1.49 D 44 3 A +0.020 0.180-0.053 0.96 D +0.10 2.90 -0.20 +0.19 1.91 -0.06 2.40 0.70 D 0.25 MIN 1.00 2 1 0.55 REF 0.25 BSC 0.95 Seating Plane Gauge Plane 8X 10 REF B PCB Layout Reference View Branded Face 1.00 0.13 0.95 BSC C Standard Branding Reference View +0.10 0.05 -0.05 A25 0.40 0.10 For Reference Only; not for tooling use (reference dwg. 802840) Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Active Area Depth, 0.28 mm REF B Reference land pattern layout All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances C Branding scale and appearance at supplier discretion D Hall element, not to scale 1 APS13290KLHA A27 1 APS13291KLHA Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 13 Precision Hall-Effect Latches for Consumer and Industrial Applications APS13290 and APS13291 Package UA, 3-Pin SIP For Reference Only - Not for Tooling Use (Reference DWG-0000406, Rev. 1) NOT TO SCALE Dimensions in millimeters Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown +0.08 4.09 -0.05 45 B C E 2.04 +0.08 3.02 -0.05 1.44 1.52 0.05 10 E E Mold Ejector Pin Indent Branded Face 0.51 REF 45 D Standard Branding Reference View 0.79 REF 1.02 MAX A26 A 1 2 1 3 APS13290KUAA A28 +0.03 0.41 -0.06 14.99 0.25 1 APS13291KUAA +0.05 0.43 -0.07 A Dambar removal protrusion (6x) B Gate and tie bar burr area C Active Area Depth, 0.50 mm 0.08 D Branding scale and appearance at supplier discretion E Hall element, not to scale 1.27 NOM Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 14 APS13290 and APS13291 Precision Hall-Effect Latches for Consumer and Industrial Applications Revision History Number Date Description - March 6, 2018 Initial release 1 February 11, 2019 Minor editorial updates Copyright (c)2019, Allegro MicroSystems, LLC Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro's products are not to be used in any devices or systems, including but not limited to life support devices or systems, in which a failure of Allegro's product can reasonably be expected to cause bodily harm. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Copies of this document are considered uncontrolled documents. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com 15