UTO SERIES
Robust Metal & Shielded Connector
3
Typical Applications .......................................... 06
Features & Bene ts .......................................... 07
Range Overview ............................................... 08
Layouts ............................................................. 10
General Technical Characteristics ..................... 12
Overview
Description ....................................................... 126
Contact Plating Selector Guide ........................ 127
Contact Selector Guide .................................... 128
Packaging ......................................................... 128
Crimp Contacts ................................................ 129
#16 Coaxial Contacts ....................................... 131
PCB Contacts ................................................... 132
Fiber Optic Contacts ........................................ 133
Contacts
#16 Coaxial Contacts/Cabling Notices ............ 168
Glossary of Terms ............................................. 175
Drilling Pattern ................................................. 176
Discrimination/Keying Methods ....................... 180
Part Number Index ........................................... 181
Appendices
Connector
Cable Assembly ................................................ 16
2 contacts + ground ......................................... 20
3 contacts + ground ......................................... 28
4 contacts ......................................................... 32
6 contacts ......................................................... 40
6 contacts + ground ......................................... 48
8 contacts ......................................................... 52
10 contacts ....................................................... 60
12 contacts ....................................................... 64
19 contacts ....................................................... 72
23 contacts ....................................................... 80
26 contacts ....................................................... 84
28 contacts ....................................................... 88
30 contacts ....................................................... 92
32 contacts ....................................................... 96
35 contacts ....................................................... 100
38 contacts ....................................................... 104
41 contacts ....................................................... 108
48 contacts ....................................................... 112
55 contacts ....................................................... 116
61 contacts ....................................................... 120
Tooling .............................................................. 139
Crimping Instructions ....................................... 140
Handle & Interchangeable Heads .................... 142
Extraction Tools ................................................ 143
Dimensions Overmoulded Harnesses .............. 143
Assembly Instructions ....................................... 144
Mated Connector Length ................................. 153
Rated Current & Working Voltage .................... 155
Shielding Effectiveness/Corrosion .................... 156
UL94 + UL1977 ................................................. 157
IEC 61984 with IP Code Explanation ................ 160
IEC 61140 Explained ........................................ 162
What is NEMA Rating ? .................................... 163
Ethernet for the Layman ................................... 164
Technical Information
UTO Series |
Contents
Appendices Technical Information Contacts
Connector
Overview
UTO SERIES
© 2013 SOURIAU - SOURIAU is a registered trademark
5
Overview
UTO Series
Typical Applications ................................................................................................ 06
Features & Bene ts ................................................................................................ 07
Range Overview ..................................................................................................... 08
Layouts ................................................................................................................... 10
General Technical Characteristics ........................................................................... 12
6
Typical Applications
UTO Series | Overview
Typical Applications
Energy - Power
Instrumentation measurement
Telecom - Data infrastructure
Robotics - Machine tools
Off road - Mining - Railway
Building Automation & Control
© Volodymyr Kyrylyuk / Fotolia
© Rainer Plendl / Fotolia
© Olivier Tuffé / Fotolia © SOURIAU
© Sergey Milovidov / Fotolia
© Vibe Images / Fotolia
7
Features & Bene ts
UTO Series | Overview
WATER
PROOF
SIGNAL
INTEGRITY
CORROSION
RESISTANT
QUICK
MATING
COST
SAVINGS
IP68/69K Dynamic Mated
Ideal for outdoor and indoor dynamic applications requiring
continuous underwater immersion, routine pressure washing
and dust protection.
1/3 Bayonet Coupling
With only 1/3 twist of the bayonet coupling system, connectors are
mated with audible "click" and tactile feel to con rm proper mating.
This mating features eliminates connection uncertainty and reduces time
and labor during installation.
Mixed Power & Signal Layouts
Power supply and signal transmission can be combined in a
unique interconnect solution to reduce system complexity and
minimize component/installation costs.
Salt Spray 48 & 96 Hours
Designed to withstand climate ingress and exposure to salt spray
or corrosive atmospheres while still maintaining mechanical and
electrical functionality.
EMI Shielded
65 dB at 100 Mhz: Quali ed and compatible to be used in
electromagnetic radiation areas and ensures proper signal integrity and
transmission.
Overview
8
UTO Series | Overview
Range
Overmoulded
Heat Shrink Boot
Adapter
Single Wire
Sealing
Straight
Strain Relief
Right Angle
Strain Relief
Short Cable
Gland
Long Cable
Gland
Plug
Sealed: IP68/69K
Shielded
Corrosion resistant
UL compliant
UTO Series
Choice of Crimp Contacts
• machined
• stamped and formed
• coaxial
• ber optics
9
UTO Series | Overview
Overview
Receptacle
Heat Shrink Boot
Adapter
Single Wire
Sealing
Straight
Strain Relief
PCB Contact
Choice of Crimp Contacts
• machined
• stamped and formed
• coaxial
• ber optics
Overview
10
Shell size Contact #16 (Ø 1.6) Contact #20 (Ø 1.0) Contact #8 (Ø 3.6) Mixed Power
10
12
14
16
UTO Series | Overview
Layouts (Electrical parameter according to IEC 61984 & IEC 61140)
103
16A 150V
2 contacts
+ground
3xØ1.6 (#16)
124
16A 150V
3 contacts
+ground
4xØ1.6 (#16)
104*
13A 150V
4 contacts
4xØ1.6 (#16)
103W3
5A 40V
6 contacts
3xØ1.6 (#16)
3xØ1.0 (#20)
106*
7A 80V
6 contacts
6xØ1.0 (#20)
102W2
25A 200V
4 contacts
2xØ2.4 (#12)
2xØ1.0 (#20)
128
10A 125V
8 contacts
8xØ1.6 (#16)
1210*
6A 40V
10 contacts
10xØ1.0 (#20)
Page 20
Page 28
142G1
40A 250V
2 contacts
+ground
3xØ3.6 (#8)
148
17A 230V
8 contacts
4xØ2.4 (#12)
4xØ1.6 (#16)
Page 24 Page 56
Page 36
Page 52
147
16A 150V
6 contacts
+ground
7xØ1.6 (#16)
Page 48
Page 60
1419
5A 40V
19 contacts
19xØ1.0 (#20)
Page 72
1412
10A 150V
12 contacts
12xØ1.6 (#16)
Page 64
1619*
9A 150V
19 contacts
19xØ1.6 (#16)
1492
10A 150V
12 contacts
12xØ1.6 (#16)
Page 76
Page 68
1626
4A 40V
26 contacts
26xØ1.0 (#20)
Page 84
Page 44 Page 32 Page 40
* Ethernet compatible see page 168 & 169
11
UTO Series | Overview
Contacts #16:
from AWG 30 to 14,
0.05 to 2.5 mm²
Contacts #20:
from AWG 26 to 18,
0.13 to 0.93 mm²
Contacts #8:
from AWG 16 to 8,
1.5 to 10 mm²
Contacts #12:
fromAWG 22 to 12,
0.13 to 4 mm²
Shell size Contact #16 (Ø 1.6) Contact #20 (Ø 1.0)
18
20
22
24
1823
8A 150V
23 contacts
23xØ1.6 (#16)
Page 80
1832
4A 50V
32 contacts
32xØ1.0 (#20)
Page 96
2028
7A 150V
28 contacts
28xØ1.6 (#16)
2030
7A 150V
30 contacts
30xØ1.6 (#16)
Page 88 Page 92
2235
6A 150V
35 contacts
35xØ1.6 (#16)
2238
6A 150V
38 contacts
38xØ1.6 (#16)
Page 100 Page 104
2448
6A 160V
48 contacts
48xØ1.6 (#16)
Page 112
2041
8A 80V
41 contacts
41xØ1.0 (#20)
Page 108
2255
3A 80V
55 contacts
55xØ1.0 (#20)
Page 116
2461
3A 80V
61 contacts
61xØ1.0 (#20)
Page 120
Overview
12
UTO Series | Overview
Materials
• Shell: Zinc alloy
• Backshells and cable glands: Brass
• Coupling ring: Aluminum alloy
• Coupling spring: Spring stainless steel
• Insert: Glass- lled thermoplast
• Contacts: See page 129
• Halogen free
• RoHS compliant & conforms to the Chinese
standard SJ/T1166-2006
(Chinese RoHS equivalent)
Environmental
• Operating temperature:
from -40°C to +105°C
40/100/21 per NFF 61-030
• Flammability rating:
UL94 V-0
I2F3 according to NFF 16101 and NFF 16102
• Salt spray:
per MIL-STD-202 method 101
- 48 h (standard version)
- 96 h (black anodized coupling ring)
Higher salt spray resistance (200/500 h)
upon request
• Sealing:
Per IEC 60529/DIN 40050: Dynamic IP67 / IP68
(under 10 m of water during 1 week) / IP69K in
mated condition and in combination with
sealed backshell.
• Fluid resistance:
- Gas and oil
- Mineral oil
- Acid bath
- Basic bath
• Shielding effectiveness:
65 dB at 100 MHz
Electrical
• In accordance with:
- UL 1977: Certi cate ECBT2
File number: E169916
- CSA C22.2: Certi cate ECBT8
File number E169916
• Also see pages 10 & 11
Mechanical
• Durability:
500 matings & unmatings per MIL-C-26482
• Vibration resistance:
55-2000 Hz, acceleration 15 g per
MIL-C-26482 (Series 1)
10-100 Hz, acceleration 2 g per NFF61030
• Thermal shock:
5 cycles 30 min. from -40°C to 105°C
per MIL-STD-202 method 207
• Mechanical shock:
50 g, 11 ms period per MIL-C-26482 (Series 1)
30 g, 18 ms period per NFF61030
General technical characteristics
13
UTO Series | Overview
Overview
UTO SERIES
© 2013 SOURIAU - SOURIAU is a registered trademark
15
Upgrade of the UTO Series .................................................................................... 16
Cable Assembly ...................................................................................................... 17
2 contacts + ground
103: 10A 500V ................................................................... 20
142G1: 44A 600V ................................................................... 24
3 contacts + ground
124: 16A 500V ................................................................... 28
4 contacts
102W2: 20A 500V ................................................................... 32
104*: 10A 500V ................................................................... 36
6 contacts
103W3: 5A 250V ................................................................... 40
106*: 5A 250V ................................................................... 44
6 contacts + ground
147: 10A 500V ................................................................... 48
8 contacts
128: 10A 500V ................................................................... 52
148: 25A 250V ................................................................... 56
10 contacts
1210*: 5A 250V ................................................................... 60
12 contacts
1412: 10A 500V ................................................................... 64
1492: 10A 500V ................................................................... 68
19 contacts
1419: 5A 250V ................................................................... 72
1619*: 9A 500V ................................................................... 76
23 contacts
1823: 8A 500V ................................................................... 80
26 contacts
1626: 4A 250V ................................................................... 84
28 contacts
2028: 5A 500V ................................................................... 88
30 contacts
2030: 5A 500V ................................................................... 92
32 contacts
1832: 4A 250V ................................................................... 96
35 contacts
2235: 5A 500V ................................................................... 100
38 contacts
2238: 5A 500V ................................................................... 104
41 contacts
2041: 3A 250V ................................................................... 108
48 contacts
2448: 5A 500V ................................................................... 112
55 contacts
2255: 3A 250V ................................................................... 116
61 contacts
2461: 3A 250V ................................................................... 120
Electrical parameters according to UL1977 * Ethernet compatible see pages 164 & 165
Connector
UTO Series
UTO Series | Connector
16
Old UTO New UTO
Upgrade of the UTO Series
Description of change:
To better meet the demanding requirements and diversity of industrial markets/applications, SOURIAU changed the position of the wavy
washer inside the plug. This slight modi cation makes the new version of the UTO sealed to IP68/69K in dynamic conditions.
Product part number:
Below is an overview of the old part numbers with the corresponding new part numbers.
Note that some of the old part numbers where backshells were included will now be sold individually, i.e. plug connector + backshell.
Old part number New part number connector New part number backshell Comments
UTO0/6-S/PT UT00/6-S/PH(6) - -
UTO0-S/PHT UT00-S/PH(6) - -
UTO0/6AC-S/PT UT00/6-S/PH(6) - -
UTO0/6PG-S/PHT UT00/6-S/PH(6) UT0-AC -
UTO-21/22- Keep old part number UT0-JC Silksreen version
UTO-44/45- Keep old part number - Screw coupling version
UTO-ACT - UT0-AC 851 backshell Nickel plated
UTO-PGT - UT0-JC Longer threading on connector side
+ metric cable gland
UTOS-PGT - UT0S-JC Longer threading on connector side
+ shielded metric cable gland
U-AD01T UT0-AD01 UT0-AD01 Longer threading to achieve sealing
U-AD01N Keep old part number - Used on old UT06-45N screw
coupling version
UTO Series | Connector
17
Connector
OUTDOOR
INDOOR
UV resistance
Ambient temperature70°C0°C
PVC
Static installation
PUR
Static or dynamic installation
Wet
Cleaner,
chlorine
Immersed
Chemical aggression
(black outer jacket)
Please consult us
TPE
Static installation SILICON
Static installation
FEP
Static installation
PTFE
Static installation
How to choose the outer jacket material
Cable Assembly
SOURIAU has provided connectors for various applications for more than 90 years and has been used in the most extreme environments.
Conscious about the dif culty in nding a quick and reliable harness manufacturer, we began our own in-house cable assembly production.
It allows customers to reduce the number of suppliers and to take advantage of the “best in class” quality of the SOURIAU group.
Overmoulding is a process that further enhances the sealing properties and helps to minimize stress on the cable termination to the
connector. In addition, the wires are encapsulated inside the molding which creates a barrier preventing liquid/moisture from entering the
equipment through the connector or cable jacket if breached.
UTO Series | Connector
18
Overmoulding Description
Discrete connector
...water ingress unhampered, leading to damage.
If cable jacket is breached...
Overmoulded connector
...prevents water ingress via capillary action.
If cable jacket is breached...
GOOD
BEST
Compound Braid Cable outer
sheath
Thermoplastic insert Overmoulding
adapter
O-ring
PVC or PUR
overmoulding
UTO Series | Connector
19
Connector
UTO Robust Metal & Shielded Cable Assembly
Description
Connector
• Shielded metal connector
• Extreme sealing: IP68/69K dynamic mated
• 26 layouts
• Rapid 1/3 turn connection
Cable
• TPE outer sheath (black)
• 300V
• Shielded
• Flammability rating UL 1581
Sec.1080 (VW-1)
Applications
• Machining Centers (Oil Resistant)
• Assembly Automation
Equipment
• Geophysical Equipment
• Solar (UV Stable)
• Outdoor Displays
PLATING SALT SPRAY DEGREE WATERPROOF COUPLING
Black anodized* 96 H -40° C up to 105° C IP68/69K
dynamic mated 500 matings/unmatings
Nickel 48 H
Speci cations
* Custom black anodized version available on demand
Harness with custom cable Harness with double ends Y or T shape connection
Custom Capabilities
UTO Series | Connector
20
OR OR
WITH
OR OR Layout
Drilling pattern see page 176
Connector Part Numbers
Contact type Connector type Sealing Salt spray
Part number
Male insert Female insert
Contacts
supplied separately
see page 23
Square ange
receptacle
IP67 96h UT00103PH UT00103SH
IP68 & IP69K 96h UT00103PH6 UT00103SH6
Plug
IP67, IP68 & IP69K 48h UT06103PH UT06103SH
IP67, IP68 & IP69K 96h UT06103PH02(Black) UT06103SH02(Black)
Jam nut
receptacle
IP67 48h UT07103PH UT07103SH
IP68 & IP69K 48h UT07103PH6 UT07103SH6
IP67 96h UT07103PH01 UT07103SH01
IP68 & IP69K 96h UT07103PH601 UT07103SH601
Backshells
103 (Shell size 10, 2 + ground, 3x#16)
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 3/6 UT010JCS UT010JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 5/8 UT010JCSL UT010JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 34/6.5 UT0S10JCS UT0S10JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 35/8.5 UT0S10JCSL UT0S10JCL
Metal cable clamp with strain relief (Fig.5) - 5 UT010AC
Metal shrink boot adaptor (Fig.6) - - UT010AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 4/10 UT010LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
34/8.8 UT0S10JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 4/10 UT010JCPGN
UTO Series | Connector
21
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
103 (Shell size 10, 2 + ground, 3x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
23.8
18.2
1.6
Female
Male
33 maxi 21.8
25.5 maxi
Ø 20.0
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
16.5
17.4
18.2
18.2
Front
mounting
Ø 14.2
Ø 3.2
Rear
mounting
Ø 17.3
Female
Male
2734 maxi
22.2
33 maxi
Ø 14.9
17.9
Short version - 49.1
Long version - 61.1
Fig. 1
Short version - 49.1
Long version - 61.1
Fig. 2
Fig. 7
48.0
30.0
Short version - 59.1
Long version - 71.1
Fig. 3
Short version - 60.1
Long version - 71.1
Fig. 4
60.6
Fig. 8
Fig. 6
Ø 21.0
24.7
Fig. 5
31.0
21.6
Ø 16.3
16A/150V
per IEC 61984
2 +
UTO Series | Connector
22
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT010DC
See page 182 for more information
Dustcap (Receptacle)
Part number
UT010DCG*
Dustcap (Plug)
Part number
UTG610DCG*
To
ol
K
it
Part number
TOOLKIT
Ha
nd
le
(without Head)
Part number
SHANDLES
Part number / Neoprene
UTFD12B
Gasket
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
103 (Shell size 10, 2 + ground, 3x#16)
Part number
RX2025GE1
Extraction Tool #16
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
UTO Series | Connector
23
Contacts
UL
10
A 5
00
V UL
9
4 V-
0
CSA
7A 5
00
V UL
9
4 V-
0
IEC
16A 150V 2.5kV 3
UTO 103 Deratin
g
Curve
s
Electrical
C
haracteristics
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
120
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
103 (Shell size 10, 2 + ground, 3x#16) 2 +
16A/150V
per IEC 61984
UTO Series | Connector
24
OR OR
WITH
OR OR Layout
Drilling pattern see page 176
Contact type Connector type Sealing Salt spray
Part number
Male insert Female insert
Contacts
supplied separately
see page 27
Square ange
receptacle
IP67 96h UT00142G1PH UT00142G1SH
IP68 & IP69K 96h UT00142G1PH6 UT00142G1SH6
Plug
IP67, IP68 & IP69K 48h UT06142G1PH UT06142G1SH
IP67, IP68 & IP69K 96h UT06142G1PH02(Black) UT06142G1SH02(Black)
Jam nut
receptacle
IP67 48h UT07142G1PH UT07142G1SH
IP68 & IP69K 48h UT07142G1PH6 UT07142G1SH6
IP67 96h UT07142G1PH01 UT07142G1SH01
IP68 & IP69K 96h UT07142G1PH601 UT07142G1SH601
Connector Part Numbers
142G1 (Shell size 14, 2 + ground, 3x#8)
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT014JCS UT014JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT014JCSL UT014JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S14JCS UT0S14JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S14JCSL UT0S14JCL
Metal cable clamp with strain relief (Fig.5) - 10 UT014AC
Metal shrink boot adaptor (Fig.6) - - UT014AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/14 UT014LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/13.5 UT0S14JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/13.5 UT014JCPGN
UTO Series | Connector
25
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
142G1 (Shell size 14, 2 + ground, 3x#8)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
33 maxi
28.6
23.0
1.6
Male
34 maxi 29.3
34
Ø 26.8
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
24.1
23.0
23.0
Front
mounting
Ø 21.5
Ø 3.2
Rear
mounting
Ø 25
25.5
Female
Male
3533.9 maxi
30.2
33 maxi
Ø 22.1
17.9
Short version - 52.1
Long version - 68.1
Fig. 1
Short version - 53.1
Long version - 69.1
Fig. 2
Fig. 7
52.0
36.5
Short version - 65.1
Long version - 81.1
Fig. 3
Short version - 65.1
Long version - 81.1
Fig. 4
67.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
34.0
27.4
Ø 22.5
40A/250V
per IEC 61984
2 +
UTO Series | Connector
26
Hand Tool
Part number
M317
Positioner + locator setting
Part number
VGE10078A
Extraction Tool #8
Part number
51060210936
Dustcap (Receptacle) Dustcap (Plug)
Part number
UT014DCG*
Part number
UTG614DCG*
Part number / Neoprene
UTFD14B
Gasket
* For dustcap without chain, skip "G", e.g. UT014DC
Accessories and Tooling
142G1 (Shell size 14, 2 + ground, 3x#8)
UTO Series | Connector
27
UL
44A 600V UL94 V-0
CSA
30A 600V UL94 V-0
IEC
40A 250V 3kV 3
Electrical Characteristics UTO 142G1 Derating Curves
Current use Limited use Not recommended use
Test
conditions
Contact used:
Machined contacts
Wires used:
6mm²
0 20 40 60 80 100 120
0
10
15
20
25
30
35
40
45
50
Current (A)
Ambient Operating Temperature (°C)
5
#8 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
16 82913601A 82913600A 1.72
6.5
14 82913603A 82913602A 2.22
12 82913605A 82913604A 2.82
10 82913607A 82913606A 3.50
882913609A 82913608A 4.35
PCB
Machined (2) -82911685NPC(1) 82911684NPC(1) --
(1): Example of plating, for other plating options see page 129
(2): For dimensions see page 132
Note: all dimensions are in mm
Contacts
142G1 (Shell size 14, 2 + ground, 3x#8)
40A/250V
per IEC 61984
2 +
UTO Series | Connector
28
OR OR
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number
Male insert Female insert
Contacts
supplied separately
see page 31
Square ange
receptacle
IP67 96h UT00124PH UT00124SH
IP68 & IP69K 96h UT00124PH6 UT00124SH6
Plug
IP67, IP68 & IP69K 48h UT06124PH UT06124SH
IP67, IP68 & IP69K 96h UT06124PH02(Black) UT06124SH02(Black)
Jam nut
receptacle
IP67 48h UT07124PH UT07124SH
IP68 & IP69K 48h UT07124PH6 UT07124SH6
IP67 96h UT07124PH01 UT07124SH01
IP68 & IP69K 96h UT07124PH601 UT07124SH601
Drilling pattern see page 176
Connector Part Numbers
124 (Shell size 12, 3 + ground, 4x#16)
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT012JCS UT012JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT012JCSL UT012JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S12JCS UT0S12JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S12JCSL UT0S12JCL
Metal cable clamp with strain relief (Fig.5) - 8.2 UT012AC
Metal shrink boot adaptor (Fig.6) - - UT012AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/12 UT012LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
304/11.9 UT0S12JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 04/11.9 UT012JCPGN
UTO Series | Connector
29
Plug - UTO6 Square Flange - UTO
0
Note: all dimensions are in mm
Dimensions
124 (Shell size 12, 3 + ground, 4x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
26.2
20.6
1.6
Male
33 maxi 26.1
25.5 maxi
Ø 23.6
Female
Short version - 49.1
Long version - 62.1
Fig. 1
Short version - 50.1
Long version - 63.1
Fig. 2
Fig. 7
50.0
33.5
Short version - 62.1
Long version - 75.1
Fig. 3
Short version - 62.1
Long version - 75.1
Fig. 4
62.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
31.5
25.0
Ø 19.4
Jam Nut - UTO7 Panel Cut Out
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
21.0
20.6
20.6
Front
mounting
Ø 18.4
Ø 3.2
Rear
mounting
Ø 21.8
22.2
Female
Male
3234 maxi
27
33 maxi
Ø 18.9
17.9
16A/150V
per IEC 61984
3 +
UTO Series | Connector
30
Dustcap (Receptacle)
Part number
UT012DCG*
Dustcap (Plug)
Part number
UTG612DCG*
Tool Kit
Part number
TOOLKIT
Handle (without Head)
Part number
SHANDLES
Part number / Neoprene
UTFD13B
Gasket
Part number
RX2025GE1
Extraction Tool #16
Accessories and Tooling
124 (Shell size 12, 3 + ground, 4x#16)
* For dustcap without chain, skip "G", e.g. UT012DC
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
31
UL
16A 500V UL94 V-0
CSA
13A 500V UL94 V-0
IEC
16A 150V 2.5kV 3
0 20 40 60 80 100 120
0
10
30
Current (A)
Ambient Operating Temperature (°C)
20
18
15
13
28
25
23
8
5
3
Electrical Characteristics UTO 124 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
Contacts
124 (Shell size 12, 3 + ground, 4x#16)
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
16A/150V
per IEC 61984
3 +
UTO Series | Connector
32
OR OR
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number
Male insert Female insert
Contacts
supplied separately
see page 35
Square ange
receptacle
IP67 96h UT00102W2PH UT00102W2SH
IP68 & IP69K 96h UT00102W2PH6 UT00102W2SH6
Plug
IP67, IP68 & IP69K 48h UT06102W2PH UT06102W2SH
IP67, IP68 & IP69K 96h UT06102W2PH02(Black) UT06102W2SH02(Black)
Jam nut
receptacle
IP67 48h UT07102W2PH UT07102W2SH
IP68 & IP69K 48h UT07102W2PH6 UT07102W2SH6
IP67 96h UT07102W2PH01 UT07102W2SH01
IP68 & IP69K 96h UT07102W2PH601 UT07102W2SH601
Drilling pattern see page 176
Connector Part Numbers
102W2 (Shell size 10, 2x#12 + 2x#20)
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 3/6 UT010JCS UT010JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 5/8 UT010JCSL UT010JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 34/6.5 UT0S10JCS UT0S10JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 35/8.5 UT0S10JCSL UT0S10JCL
Metal cable clamp with strain relief (Fig.5) - 5 UT010AC
Metal shrink boot adaptor (Fig.6) - - UT010AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 4/10 UT010LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
34/8.8 UT0S10JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 4/10 UT010JCPGN
UTO Series | Connector
33
Note: all dimensions are in mm
Dimensions
102W2 (Shell size 10, 2x#12 + 2x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
32 maxi
23.8
18.2
1.6
Female
Male
33 maxi 21.8
25.5 maxi
Ø 20
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
16.5
17.4
18.2
18.2
Front
mounting
Ø 14.2
Ø 3.2
Rear
mounting
Ø 17.3
Female
Male
2734 maxi
22.2
33 maxi
Ø 14.9
17.9
Short version - 49.1
Long version - 61.1
Fig. 1
Short version - 49.1
Long version - 61.1
Fig. 2
Fig. 7
48.0
30.0
Short version - 59.1
Long version - 71.1
Fig. 3
Short version - 60.1
Long version - 71.1
Fig. 4
60.6
Fig. 8
Fig. 6
Ø 21.0
24.7
Fig. 5
31.0
21.6
Ø 16.3
25A/200V
per IEC 61984
4
UTO Series | Connector
34
Crimp Tooling #12
Extraction Tooling #12
Part number
Extraction Tool
51060210924
Part number
positioner + locator setting
VGE10077A
Part number Hand Tool
M317
Dustcap (Receptacle)
Part number
UT010DCG*
Dustcap (Plug)
Part number
UTG610DCG*
Part number / Neoprene
UTFD12B
Gasket
Crimp Tooling #20
Part number
TOOLKIT
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
Part number
SHANDLES
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
+=
Handle Head Complete set
* For dustcap without chain, skip "G", e.g. UT010DC
102W2 (Shell size 10, 2x#12 + 2x#20)
Accessories and Tooling
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
35
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6 or SM24WL3S26
(3): For dimensions see page 132
UL
20A 500V UL94 V-0
CSA
18A 500V UL94 V-0
IEC
25A 200V 3kV 3
Electrical Characteristics UTO 102W2 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
3.300mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
5
10
15
20
25
30
35
40
45
50
Current (A)
Ambient Operating Temperature (°C)
Note: all dimensions are in mm
102W2 (Shell size 10, 2x#12 + 2x#20)
Contacts
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
#12
Crimp
Machined
22 82911457NA 82911456A 0.87
4.90
20 82911459NA 82911458A 1.12
18 82911461NA 82911460A 1.42
16 82911463NA 82911462A 1.72
14 82911465NA 82911464A 2.22
12 82911467NA 82911466A 2.82
25A/200V
per IEC 61984
4
UTO Series | Connector
36
OR
OR
OR WITH
WITH
OR OR
SINGLE WIRE SEALING (1)
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 39
Square ange
receptacle
IP67 96h UT00104PH UT00104SH
IP68 & IP69K 96h UT00104PH6 UT00104SH6
Plug
IP67, IP68 & IP69K 48h UT06104PH(1) UT06104SH(1)
IP67, IP68 & IP69K 96h UT06104PH02(1) (Black) UT06104SH02(1) (Black)
Jam nut
receptacle
IP67 48h UT07104PH(1) UT07104SH(1)
IP68 & IP69K 48h UT07104PH6(1) UT07104SH6(1)
IP67 96h UT07104PH01(1) UT07104SH01(1)
IP68 & IP69K 96h UT07104PH601(1) UT07104SH601 (1)
Drilling pattern see page 176
* Other discrimination keying option, see page 182
Connector Part Numbers
104 (Shell size 10, 4x#16)
(1): For single wire sealing solution please add GN or GJC after UT06 or UT07. Eg UT07GN104PH
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 3/6 UT010JCS UT010JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 5/8 UT010JCSL UT010JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 34/6.5 UT0S10JCS UT0S10JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 35/8.5 UT0S10JCSL UT0S10JCL
Metal cable clamp with strain relief (Fig.5) - 5 UT010AC
Metal shrink boot adaptor (Fig.6) - - UT010AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 4/10 UT010LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
34/8.8 UT0S10JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 4/10 UT010JCPGN
UTO Series | Connector
37
Note: all dimensions are in mm
Dimensions
104 (Shell size 10, 4x#16)
Backshells (for Mated Connector Length: See Page 157)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Female
Male
11.3
33.3 maxi
25.2 maxi
23.8
18.2
1.6
Female
Male
33 maxi 21.8
25.5 maxi
Ø 20
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
16.5
17.4
18.2
18.2
Front
mounting
Ø 14.2
Ø 3.2
Rear
mounting
Ø 17.3
Female
Male
2734 maxi
22.2
33 maxi
Ø 14.9
17.9
Short version - 49.1
Long version - 61.1
Fig. 1
Short version - 49.1
Long version - 61.1
Fig. 2
Fig. 7
48.0
30.0
Short version - 59.1
Long version - 71.1
Fig. 3
Short version - 60.1
Long version - 71.1
Fig. 4
60.6
Fig. 8
Fig. 6
Ø 21.0
24.7
Fig. 5
31.0
21.6
Ø 16.3
GN plastic
Ø 22.0
13.0
GJC plastic
Ø 22.0
49.9
13A/150V
per IEC 61984
4
UTO Series | Connector
38
Dustcap (Receptacle)
Part number
UT010DCG*
Dustcap (Plug)
Part number
UTG610DCG*
Tool Kit
Part number
TOOLKIT
Handle (without Head)
Part number
SHANDLES
Part number / Neoprene
UTFD12B
Gasket
104 (Shell size 10, 4x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT010DC
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
39
UL
10A 500V UL94 V-0
CSA
7A 500V UL94 V-0
IEC
13A 150V 2.5kV 3
Electrical Characteristics UTO 104 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
120
104 (Shell size 10, 4x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
13A/150V
per IEC 61984
4
UTO Series | Connector
40
OR OR
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number
Male insert Female insert
Contacts
supplied separately
see page 43
Square ange
receptacle
IP67 96h UT00103W3PH UT00103W3SH
IP68 & IP69K 96h UT00103W3PH6 UT00103W3SH6
Plug
IP67, IP68 & IP69K 48h UT06103W3PH UT06103W3SH
IP67, IP68 & IP69K 96h UT06103W3PH02(Black) UT06103W3SH02(Black)
Jam nut
receptacle
IP67 48h UT07103W3PH UT07103W3SH
IP68 & IP69K 48h UT07103W3PH6 UT07103W3SH6
IP67 96h UT07103W3PH01 UT07103W3SH01
IP68 & IP69K 96h UT07103W3PH601 UT07103W3SH601
Drilling pattern see page 176
103W3 (Shell size 10, 3x#16 + 3x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 3/6 UT010JCS UT010JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 5/8 UT010JCSL UT010JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 34/6.5 UT0S10JCS UT0S10JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 35/8.5 UT0S10JCSL UT0S10JCL
Metal cable clamp with strain relief (Fig.5) - 5 UT010AC
Metal shrink boot adaptor (Fig.6) - - UT010AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 4/10 UT010LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
34/8.8 UT0S10JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 4/10 UT010JCPGN
UTO Series | Connector
41
Note: all dimensions are in mm
Dimensions
103W3 (Shell size 10, 3x#16 + 3x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
36 maxi
25.2 maxi
23.8
18.2
1.6
Female
Male
35 maxi 21.8
27 maxi
Ø 20
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
16.5
17.4
18.2
18.2
Front
mounting
Ø 14.2
Ø 3.2
Rear
mounting
Ø 17.3
Female
Male
2734 maxi
22.2
33 maxi
Ø 14.9
17.9
Short version - 49.1
Long version - 61.1
Fig. 1
Short version - 49.1
Long version - 61.1
Fig. 2
Fig. 7
48.0
30.0
Short version - 59.1
Long version - 71.1
Fig. 3
Short version - 60.1
Long version - 71.1
Fig. 4
60.6
Fig. 8
Fig. 6
Ø 21.0
24.7
Fig. 5
31.0
21.6
Ø 16.3
5A/40V
per IEC 61984
6
UTO Series | Connector
42
Crimp Tooling (without Shandles)
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM
RM/RC 20W3K(1) S20RCM
RM/RC 18W3K(1) S20RCM
SM/SC 24WL3(1)(2) S20SCM20
SM/SC 20WL3(1)(2) S20SCM20
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
Dustcap (Receptacle)
Part number
UT010DCG*
Dustcap (Plug)
Part number
UTG610DCG*
Part number / Neoprene
UTFD12B
Gasket
+=
Handle Head Complete set
Part number
RX20D44
Extraction Tool #20
103W3 (Shell size 10, 3x#16 + 3x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT010DC
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
UTO Series | Connector
43
UL
5A 250V UL94 V-0
CSA
5A 200V UL94 V-0
IEC
5A 40V 1.5kV 3
UTO 103W3 Derating CurvesElectrical Characteristics
Test
conditions
Contact used:
Machined contacts
Wires used:
1.310mm²
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
#20
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
120
Note: all dimensions are in mm
103W3 (Shell size 10, 3x#16 + 3x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6 or SM24WL3S26
(3): For dimensions see page 132
5A/40V
per IEC 61984
6
UTO Series | Connector
44
OR OR
WITH
OR OR
Layout
* Other discrimination keying option, see page 182
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 47
Square ange
receptacle
IP67 96h UT0W0106PH UT0W0106SH
IP68 & IP69K 96h UT0W0106PH6 UT0W0106SH6
Plug
IP67, IP68 & IP69K 48h UT0W6106PH UT0W6106SH
IP67, IP68 & IP69K 96h UT0W6106PH02(Black) UT0W6106SH02(Black)
Jam nut
receptacle
IP67 48h UT0W7106PH UT0W7106SH
IP68 & IP69K 48h UT0W7106PH6 UT0W7106SH6
IP67 96h UT0W7106PH01 UT0W7106SH01
IP68 & IP69K 96h UT0W7106PH601 UT0W7106SH601
Drilling pattern see page 176
106 (Shell size 10, 6x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 3/6 UT010JCS UT010JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 5/8 UT010JCSL UT010JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 34/6.5 UT0S10JCS UT0S10JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 35/8.5 UT0S10JCSL UT0S10JCL
Metal cable clamp with strain relief (Fig.5) - 5 UT010AC
Metal shrink boot adaptor (Fig.6) - - UT010AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 4/10 UT010LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
34/8.8 UT0S10JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 4/10 UT010JCPGN
UTO Series | Connector
45
Note: all dimensions are in mm
Dimensions
106 (Shell size 10, 6x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
23.8
18.2
1.6
Female
Male
33 maxi 21.8
25.5 maxi
Ø 20
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
16.5
17.4
18.2
18.2
Front
mounting
Ø 14.2
Ø 3.2
Rear
mounting
Ø 17.3
Female
Male
2734 maxi
22.2
33 maxi
Ø 14.9
17.9
Short version - 49.1
Long version - 61.1
Fig. 1
Short version - 49.1
Long version - 61.1
Fig. 2
Fig. 7
48.0
30.0
Short version - 59.1
Long version - 71.1
Fig. 3
Short version - 60.1
Long version - 71.1
Fig. 4
60.6
Fig. 8
Fig. 6
Ø 21.0
24.7
Fig. 5
31.0
21.6
Ø 16.3
7A/80V
per IEC 61984
6
UTO Series | Connector
46
Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
Dustcap (Receptacle)
Part number
UT010DCG*
Dustcap (Plug)
Part number
UTG610DCG*
Part number / Neoprene
UTFD12B
Gasket
+=
Handle Head Complete set
* For dustcap without chain, skip "G", e.g. UT024DC
106 (Shell size 10, 6x#20)
Accessories and Tooling
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
47
UL
5A 250V UL94 V-0
CSA
4A 250V UL94 V-0
IEC
7A 80V 1.5kV 3
Electrical Characteristics UTO 106 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100 120
0
4
2
6
8
10
12
14
Current (A)
Ambient Operating Temperature (°C)
106 (Shell size 10, 6x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
7A/80V
per IEC 61984
6
UTO Series | Connector
48
OR
OR
OR WITH
WITH
OR OR
SINGLE WIRE SEALING (1)
Layout
Contact type Connector type Sealing Salt spray Part number
Male insert Female insert
Contacts
supplied separately
see page 51
Square ange
receptacle
IP67 96h UT00147PH UT00147SH
IP68 & IP69K 96h UT00147PH6 UT00147SH6
Plug
IP67, IP68 & IP69K 48h UT06147PH(1) UT06147SH(1)
IP67, IP68 & IP69K 96h UT06147PH02(1) (Black) UT06147SH02(1) (Black)
Jam nut
receptacle
IP67 48h UT07147PH(1) UT07147SH(1)
IP68 & IP69K 48h UT07147PH6(1) UT07147SH6(1)
IP67 96h UT07147PH01(1) UT07147SH01(1)
IP68 & IP69K 96h UT07147PH601(1) UT07147SH601(1)
Drilling pattern see page 176
147 (Shell size 14, 6 + ground, 7x#16)
Connector Part Numbers
(1): For single wire sealing solution please add GN or GJC after UT06 or UT07. Eg UT07GN147PH
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT014JCS UT014JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT014JCSL UT014JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S14JCS UT0S14JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S14JCSL UT0S14JCL
Metal cable clamp with strain relief (Fig.5) - 10 UT014AC
Metal shrink boot adaptor (Fig.6) - - UT014AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/14 UT014LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/13.5 UT0S14JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/13.5 UT014JCPGN
UTO Series | Connector
49
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
147 (Shell size 14, 6 + ground, 7x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
28.6
23.0
1.6
Male
33 maxi 29.3
25.5 maxi
Ø 26.8
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
24.1
25.5
23.0
23.0
Front
mounting
Ø 21.5
Ø 3.2
Rear
mounting
Ø 25
Female
Male
3534 maxi
30.2
33 maxi
Ø 22.1
17.9
Short version - 52.1
Long version - 68.1
Fig. 1
Short version - 53.1
Long version - 69.1
Fig. 2
Fig. 7
52.0
36.5
Short version - 65.1
Long version - 81.1
Fig. 3
Short version - 65.1
Long version - 81.1
Fig. 4
67.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
34.0
27.4
Ø 22.5
GN plastic
Ø 29.8
9.5
GJC plastic
Ø 29.8
52.0
16A/150V
per IEC 61984
6
UTO Series | Connector
50
Dustcap (Receptacle)
Part number
UT014DCG*
Dustcap (Plug)
Part number
UTG614DCG*
Part number / Neoprene
UTFD14B
Gasket
147 (Shell size 14, 6 + ground, 7x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT014DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
51
UL
10A 500V UL94 V-0
CSA
7A 500V UL94 V-0
IEC
16A 150V 2.5kV 3
Electrical Characteristics UTO 147 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100 120
0
5
3
8
10
20
18
15
13
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
147 (Shell size 14, 6 + ground, 7x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
16A/150V
per IEC 61984
6
UTO Series | Connector
52
OR
OR
SINGLE WIRE SEALING (1)
OR WITH
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 55
Square ange
receptacle
IP67 96h UT00128PH UT00128SH
IP68 & IP69K 96h UT00128PH6 UT00128SH6
Plug
IP67, IP68 & IP69K 48h UT06128PH(1) UT06128SH(1)
IP67, IP68 & IP69K 96h UT06128PH02(1) (Black) UT06128SH02(1) (Black)
Jam nut
receptacle
IP67 48h UT07128PH(1) UT07128SH(1)
IP68 & IP69K 48h UT07128PH6(1) UT07128SH6(1)
IP67 96h UT07128PH01(1) UT07128SH01(1)
IP68 & IP69K 96h UT07128PH601(1) UT07128SH601(1)
Drilling pattern see page 176
128 (Shell size 12, 8x#16)
Connector Part Numbers
* Other discrimination keying option, see page 182 (1): For single wire sealing solution please add GN or GJC after UT06 or UT07. Eg UT07GN128PH
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT012JCS UT012JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT012JCSL UT012JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S12JCS UT0S12JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S12JCSL UT0S12JCL
Metal cable clamp with strain relief (Fig.5) - 8.2 UT012AC
Metal shrink boot adaptor (Fig.6) - - UT012AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/12 UT012LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
304/11.9 UT0S12JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 04/11.9 UT012JCPGN
UTO Series | Connector
53
Note: all dimensions are in mm
Dimensions
128 (Shell size 12, 8x#16)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
26.2
20.6
1.6
Male
33 maxi 26.1
25.5 maxi
Ø 23.6
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
21.0
20.6
20.6
Front
mounting
Ø 18.4
Ø 3.2
Rear
mounting
Ø 21.8
22.2
Female
Male
3234 maxi
27
33 maxi
Ø 18.9
17.9
Short version - 49.1
Long version - 62.1
Fig. 1
Short version - 50.1
Long version - 63.1
Fig. 2
Fig. 7
50.0
33.5
Short version - 62.1
Long version - 75.1
Fig. 3
Short version - 62.1
Long version - 75.1
Fig. 4
62.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
31.5
25.0
Ø 19.4
GN plastic
Ø 25.4
10.7
GJC plastic
Ø 25.4
49.9
10A/125V
per IEC 61984
8
UTO Series | Connector
54
Dustcap (Receptacle)
Part number
UT012DCG*
Dustcap (Plug)
Part number
UTG612DCG*
Part number / Neoprene
UTFD13B
Gasket
128 (Shell size 12, 8x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT012DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
55
UL
10A 500V UL94 V-0
CSA
7A 500V UL94 V-0
IEC
10A 125V 2.5kV 3
Electrical Characteristics UTO 128 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
120
128 (Shell size 12, 8x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
10A/125V
per IEC 61984
8
UTO Series | Connector
56
OR OR WITH
OR OR
Layout
Drilling pattern see page 176
Contact type Connector type Sealing Salt spray Part number
Male insert Female insert
Contacts
supplied separately
see page 59
Square ange
receptacle
IP67 96h UT00148PH UT00148SH
IP68 & IP69K 96h UT00148PH6 UT00148SH6
Plug
IP67, IP68 & IP69K 48h UT06148PH UT06148SH
IP67, IP68 & IP69K 96h UT06148PH02(Black) UT06148SH02(Black)
Jam nut
receptacle
IP67 48h UT07148PH UT07148SH
IP68 & IP69K 48h UT07148PH6 UT071482SH6
IP67 96h UT071482PH01 UT07148SH01
IP68 & IP69K 96h UT07148PH601 UT07148SH601
148 (Shell size 14, 4x#12 + 4x#16)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT014JCS UT014JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT014JCSL UT014JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S14JCS UT0S14JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S14JCSL UT0S14JCL
Metal cable clamp with strain relief (Fig.5) - 10 UT014AC
Metal shrink boot adaptor (Fig.6) - - UT014AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/14 UT014LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/13.5 UT0S14JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/13.5 UT014JCPGN
UTO Series | Connector
57
Note: all dimensions are in mm
Dimensions
148 (Shell size 14, 4x#12 + 4x#16)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
32 maxi
28.6
23.0
1.6
Male
35 maxi 29.3
33 maxi
Ø 26.8
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
24.1
23.0
23.0
Front
mounting
Ø 21.5
Ø 3.2
Rear
mounting
Ø 25
25.5
Female
Male
3534 maxi
30.2
33 maxi
Ø 22.1
17.9
Short version - 52.1
Long version - 68.1
Fig. 1
Short version - 53.1
Long version - 69.1
Fig. 2
Fig. 7
52.0
36.5
Short version - 65.1
Long version - 81.1
Fig. 3
Short version - 65.1
Long version - 81.1
Fig. 4
67.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
34.0
27.4
Ø 22.5
17A/230V
per IEC 61984
8
UTO Series | Connector
58
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT014DC
148 (Shell size 14, 4x#12 + 4x#16)
Dustcap (Receptacle)
Part number
UT014DCG*
Dustcap (Plug)
Part number
UTG614DCG*
Part number / Neoprene
UTFD14B
Gasket
Crimp Tooling #12
Part number
Extraction Tool
51060210924
Part number
positioner + locator setting
VGE10078A
Part number Hand Tool
M317
Extraction Tool #16
Part number
RX20D44
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
59
Contacts
148 (Shell size 14, 4x#12 + 4x#16)
UL
25A 250V UL94 V-0
CSA
17A 250V UL94 V-0
IEC
17A 230V 1.5kV 3
Electrical Characteristics
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
#12
Crimp
Machined
22 82911457NA 82911456A 0.87
4.90
20 82911459NA 82911458A 1.12
18 82911461NA 82911460A 1.42
16 82911463NA 82911462A 1.72
14 82911465NA 82911464A 2.22
12 82911467NA 82911466A 2.82
UTO 148 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
3.30mm²
Current use Limited use Not recommended use
0 25 45 65 85 105
0
5
10
15
20
25
30
Current (A)
Ambient Operating Temperature (°C)
125
35
40
45
Note: all dimensions are in mm
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
17A/230V
per IEC 61984
8
UTO Series | Connector
60
OR OR
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 63
Square ange
receptacle
IP67 96h UT0W01210PH UT0W01210SH
IP68 & IP69K 96h UT0W01210PH6 UT0W01210SH6
Plug
IP67, IP68 & IP69K 48h UT0W61210PH UT0W61210SH
IP67, IP68 & IP69K 96h UT0W61210PH02(Black) UT0W61210SH02(Black)
Jam nut
receptacle
IP67 48h UT0W71210PH UT0W71210SH
IP68 & IP69K 48h UT0W71210PH6 UT0W71210SH6
IP67 96h UT0W71210PH01 UT0W71210SH01
IP68 & IP69K 96h UT0W71210PH601 UT0W71210SH601
* Other discrimination keying option, see page 182
Drilling pattern see page 176
1210 (Shell size 12, 10x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT012JCS UT012JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT012JCSL UT012JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S12JCS UT0S12JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S12JCSL UT0S12JCL
Metal cable clamp with strain relief (Fig.5) - 8.2 UT012AC
Metal shrink boot adaptor (Fig.6) - - UT012AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/12 UT012LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
304/11.9 UT0S12JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 04/11.9 UT012JCPGN
UTO Series | Connector
61
Note: all dimensions are in mm
Dimensions
1210 (Shell size 12, 10x#20)
Plug - UTO6 Square Flange - UTO
0
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
26.2
20.6
1.6
Male
33 maxi 26.1
25.5 maxi
Ø 23.6
Female
Short version - 49.1
Long version - 62.1
Fig. 1
Short version - 50.1
Long version - 63.1
Fig. 2
Fig. 7
50.0
33.5
Short version - 62.1
Long version - 75.1
Fig. 3
Short version - 62.1
Long version - 75.1
Fig. 4
62.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
31.5
25.0
Ø 19.4
Jam Nut - UTO7 Panel Cut Out
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
21.0
20.6
20.6
Front
mounting
Ø 18.4
Ø 3.2
Rear
mounting
Ø 21.8
22.2
Female
Male
3234 maxi
27
33 maxi
Ø 18.9
17.9
6A/40V
per IEC 61984
10
UTO Series | Connector
62
Dustcap (Receptacle)
Part number
UT012DCG*
Dustcap (Plug)
Part number
UTG612DCG*
Part number / Neoprene
UTFD13B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
1210 (Shell size 12, 10x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT012DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
63
UL
5A 250V UL94 V-0
CSA
4A 250V UL94 V-0
IEC
6A 40V 1.5kV 3
Electrical Characteristics UT0 1210 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
2
4
6
8
10
12
Current (A)
Ambient Operating Temperature (°C)
120
1210 (Shell size 12, 10x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
6A/40V
per IEC 61984
10
UTO Series | Connector
64
OR
OR
OR WITH
WITH
OR OR
SINGLE WIRE SEALING (1)
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 67
Square ange
receptacle
IP67 96h UT001412PH UT001412SH
IP68 & IP69K 96h UT001412PH6 UT001412SH6
Plug
IP67, IP68 & IP69K 48h UT061412PH(1) UT061412SH(1)
IP67, IP68 & IP69K 96h UT061412PH02(1) (Black) UT061412SH02(1) (Black)
Jam nut
receptacle
IP67 48h UT071412PH(1) UT071412SH(1)
IP68 & IP69K 48h UT071412PH6(1) UT071412SH6(1)
IP67 96h UT071412PH01(1) UT071412SH01(1)
IP68 & IP69K 96h UT071412PH601(1) UT071412SH601(1)
Drilling pattern see page 176
1412 (Shell size 14, 12x#16)
Connector Part Numbers
* Other discrimination keying option, see page 182 (1): For single wire sealing solution please add GN or GJC after UT06 or UT07. Eg UT07GN1412PH
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT014JCS UT014JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT014JCSL UT014JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S14JCS UT0S14JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S14JCSL UT0S14JCL
Metal cable clamp with strain relief (Fig.5) - 10 UT014AC
Metal shrink boot adaptor (Fig.6) - - UT014AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/14 UT014LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/13.5 UT0S14JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/13.5 UT014JCPGN
UTO Series | Connector
65
Note: all dimensions are in mm
Dimensions
1412 (Shell size 14, 12x#16)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
28.6
23.0
1.6
Male
33 maxi 29.3
25.5 maxi
Ø 26.8
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
24.1
25.5
23.0
23.0
Front
mounting
Ø 21.5
Ø 3.2
Rear
mounting
Ø 25
Female
Male
3534 maxi
30.2
33 maxi
Ø 22.1
17.9
Short version - 52.1
Long version - 68.1
Fig. 1
Short version - 53.1
Long version - 69.1
Fig. 2
Fig. 7
52.0
36.5
Short version - 65.1
Long version - 81.1
Fig. 3
Short version - 65.1
Long version - 81.1
Fig. 4
67.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
34.0
27.4
Ø 22.5
GN plastic
Ø 29.8
9.5
GJC plastic
Ø 29.8
52.0
10A/150V
per IEC 61984
12
UTO Series | Connector
66
Dustcap (Receptacle)
Part number
UT014DCG*
Dustcap (Plug)
Part number
UTG614DCG*
Part number / Neoprene
UTFD14B
Gasket
1412 (Shell size 14, 12x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT014DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
67
UL
10A 500V UL94 V-0
CSA
7A 500V UL94 V-0
IEC
10A 150V 2.5kV 3
Electrical Characteristics UTO 1412 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
120
1412 (Shell size 14, 12x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
10A/150V
per IEC 61984
12
UTO Series | Connector
68
OR OR
WITH
OR OR
Connector Part Numbers
1492 (Shell size 14, 12x#16)
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 71
Square ange
receptacle
IP67 96h UT001492PH UT001492SH
IP68 & IP69K 96h UT001492PH6 UT001492SH6
Plug
IP67, IP68 & IP69K 48h UT0614912PH UT061492SH
IP67, IP68 & IP69K 96h UT0614192PH02(Black) UT061492SH02(Black)
Jam nut
receptacle
IP67 48h UT071492PH UT071492SH
IP68 & IP69K 48h UT071492PH6 UT071492SH6
IP67 96h UT071492PH01 UT071492SH01
IP68 & IP69K 96h UT071492PH601 UT071492SH601
Drilling pattern see page 176
* Other discrimination keying option, see page 182
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT014JCS UT014JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT014JCSL UT014JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S14JCS UT0S14JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S14JCSL UT0S14JCL
Metal cable clamp with strain relief (Fig.5) - 10 UT014AC
Metal shrink boot adaptor (Fig.6) - - UT014AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/14 UT014LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/13.5 UT0S14JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/13.5 UT014JCPGN
UTO Series | Connector
69
Note: all dimensions are in mm
Dimensions
1492 (Shell size 14, 12x#16)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
28.6
23.0
1.6
Male
33 maxi 29.3
25.5 maxi
Ø 26.8
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
24.1
23.0
23.0
Front
mounting
Ø 21.5
Ø 3.2
Rear
mounting
Ø 25
25.5
Female
Male
3534 maxi
30.2
33 maxi
Ø 22.1
17.9
Short version - 52.1
Long version - 68.1
Fig. 1
Short version - 53.1
Long version - 69.1
Fig. 2
Fig. 7
52.0
36.5
Short version - 65.1
Long version - 81.1
Fig. 3
Short version - 65.1
Long version - 81.1
Fig. 4
67.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
34.0
27.4
Ø 22.5
10A/150V
per IEC 61984
12
UTO Series | Connector
70
1492 (Shell size 14, 12x#16)
Dustcap (Receptacle)
Part number
UT014DCG*
Dustcap (Plug)
Part number
UTG614DCG*
Part number / Neoprene
UTFD14B
Gasket
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT014DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
71
1492 (Shell size 14, 12x#16)
UL
10A 500V UL94 V-0
CSA
7A 500V UL94 V-0
IEC
10A 150V 2.5kV 3
Electrical Characteristics UTO 1492 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
120
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
10A/150V
per IEC 61984
12
UTO Series | Connector
72
OR OR
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 75
Square ange
receptacle
IP67 96h UT0W01419PH UT0W01419SH
IP68 & IP69K 96h UT0W01419PH6 UT0W01419SH6
Plug
IP67, IP68 & IP69K 48h UT0W61419PH UT0W61419SH
IP67, IP68 & IP69K 96h UT0W61419PH02(Black) UT0W61419SH02(Black)
Jam nut
receptacle
IP67 48h UT0W71419PH UT0W71419SH
IP68 & IP69K 48h UT0W71419PH6 UT0W71419SH6
IP67 96h UT0W71419PH01 UT0W71419SH01
IP68 & IP69K 96h UT0W71419PH601 UT0W71419SH601
* Other discrimination keying option, see page 182
Drilling pattern see page 176
1419 (Shell size 14, 19x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 06/10 UT014JCS UT014JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 08/12 UT014JCSL UT014JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 307/10.5 UT0S14JCS UT0S14JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 308/12.5 UT0S14JCSL UT0S14JCL
Metal cable clamp with strain relief (Fig.5) - 10 UT014AC
Metal shrink boot adaptor (Fig.6) - - UT014AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/14 UT014LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/13.5 UT0S14JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/13.5 UT014JCPGN
UTO Series | Connector
73
Note: all dimensions are in mm
Dimensions
1419 (Shell size 14, 19x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
28.6
23.0
1.6
Male
33 maxi 29.3
25.5 maxi
Ø 26.8
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
24.1
23.0
23.0
Front
mounting
Ø 21.5
Ø 3.2
Rear
mounting
Ø 25
25.5
Female
Male
3534 maxi
30.2
33 maxi
Ø 22.1
17.9
Short version - 52.1
Long version - 68.1
Fig. 1
Short version - 53.1
Long version - 69.1
Fig. 2
Fig. 7
52.0
36.5
Short version - 65.1
Long version - 81.1
Fig. 3
Short version - 65.1
Long version - 81.1
Fig. 4
67.7
Fig. 8
Fig. 6
Ø 27.0
24.7
Fig. 5
34.0
27.4
Ø 22.5
5A/40V
per IEC 61984
19
UTO Series | Connector
74
Dustcap (Receptacle)
Part number
UT014DCG*
Dustcap (Plug)
Part number
UTG614DCG*
Part number / Neoprene
UTFD14B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
1419 (Shell size 14, 19x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT014DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
75
UL
5A 250V UL94 V-0
CSA
4A 250V UL94 V-0
IEC
5A 40V 1.5kV 3
Electrical Characteristics UTO 1419 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
2
4
6
8
10
12
Current (A)
Ambient Operating Temperature (°C)
120
1419 (Shell size 14, 19x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
5A/40V
per IEC 61984
19
UTO Series | Connector
76
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 79
Square ange
receptacle
IP67 96h UT001619PH UT001619SH
IP68 & IP69K 96h UT001619PH6 UT001619SH6
Plug
IP67, IP68 & IP69K 48h UT061619PH UT061619SH
IP67, IP68 & IP69K 96h UT061619PH02(Black) UT061619SH02(Black)
Jam nut
receptacle
IP67 48h UT071619PH UT071619SH
IP68 & IP69K 48h UT071619PH6 UT071619SH6
IP67 96h UT071619PH01 UT071619SH01
IP68 & IP69K 96h UT071619PH601 UT071619SH601
* Other discrimination keying option, see page 182
Layout
Drilling pattern see page 177
1619 (Shell size 16, 19x#16)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 9.5/14 UT016JCS UT016JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 11.5/18 UT016JCSL UT016JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 310/14.5 UT0S16JCS UT0S16JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 313.5/18 UT0S16JCSL UT0S16JCL
Metal cable clamp with strain relief (Fig.5) - 13 UT016AC
Metal shrink boot adaptor (Fig.6) - - UT016AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/16 UT016LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/16 UT0S16JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/16 UT016JCPGN
UTO Series | Connector
77
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
1619 (Shell size 16, 19x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
31.0
24.6
1.6
Male
33 maxi 32.45
25.5 maxi
Ø 30.0
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
27.2
24.6
24.6
Front
mounting
Ø 24.6
Ø 3.2
Rear
mounting
Ø 28.1
28.3
Female
Male
38.134 maxi
33.3
33 maxi
Ø 25.3
17.9
Short version - 63.1
Long version - 74.1
Fig. 1
Short version - 69.1
Long version - 80.1
Fig. 2
Fig. 7
55.0
39.5
Short version - 73.1
Long version - 84.1
Fig. 3
Short version - 83.1
Long version - 94.1
Fig. 4
73.1
Fig. 8
Fig. 6
Ø 30.0
27
Fig. 5
34.0
29.4
Ø 25.8
9A/150V
per IEC 61984
19
UTO Series | Connector
78
Dustcap (Receptacle)
Part number
UT016DCG*
Dustcap (Plug)
Part number
UTG616DCG*
Part number / Neoprene
UTFD15B
Gasket
1619 (Shell size 16, 19x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT016DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
79
UL
9A 500V UL94 V-0
CSA
6A 500V UL94 V-0
IEC
9A 150V 2.5kV 3
Electrical Characteristics UTO 1619 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
5
10
15
20
25
28
Current (A)
Ambient Operating Temperature (°C)
120
1619 (Shell size 16, 19x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
9A/150V
per IEC 61984
19
UTO Series | Connector
80
OR OR
WITH
OR OR
Layout
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 83
Square ange
receptacle
IP67 96h UT001823PH UT001823SH
IP68 & IP69K 96h UT001823PH6 UT001823SH6
Plug
IP67, IP68 & IP69K 48h UT061823PH UT061823SH
IP67, IP68 & IP69K 96h UT061823PH02(Black) UT061823SH02(Black)
Jam nut
receptacle
IP67 48h UT071823PH UT071823SH
IP68 & IP69K 48h UT071823PH6 UT071823SH6
IP67 96h UT071823PH01 UT071823SH01
IP68 & IP69K 96h UT071823PH601 UT071823SH601
* Other discrimination keying option, see page 182
Drilling pattern see page 177
1823 (Shell size 18, 23x#16)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 9.5/14 UT018JCS UT018JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 11.5/18 UT018JCSL UT018JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 310/14.5 UT0S18JCS UT0S18JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 313.5/18 UT0S18JCSL UT0S18JCL
Metal cable clamp with strain relief (Fig.5) - 16.0 UT018AC
Metal shrink boot adaptor (Fig.6) - - UT018AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT018LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/16 UT0S18JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/16 UT018JCPGN
UTO Series | Connector
81
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
1823 (Shell size 18, 23x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
33.3
26.9
1.6
Male
33 maxi 35.2
25.5 maxi
Ø 33.3
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
30.3
26.9
26.9
Front
mounting
Ø 27.8
Ø 3.2
Rear
mounting
Ø 31.3
31.8
Female
Male
41.334 maxi
36.5
33 maxi
Ø 28.4
17.9
Short version - 66.1
Long version - 76.6
Fig. 1
Short version - 72.1
Long version - 82.6
Fig. 2
Fig. 7
60.0
46.0
Short version - 76.1
Long version - 86.6
Fig. 3
Short version - 86.1
Long version - 96.6
Fig. 4
77.2
Fig. 8
Fig. 6
Ø 33.3
27
Fig. 5
31.4
35.2
Ø 33.3
8A/150V
per IEC 61984
23
UTO Series | Connector
82
Dustcap (Receptacle)
Part number
UT018DCG*
Dustcap (Plug)
Part number
UTG618DCG*
Part number / Neoprene
UTFD16B
Gasket
1823 (Shell size 18, 23x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT018DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
83
UL
8A 500V UL94 V-0
CSA
7A 500V UL94 V-0
IEC
8A 150V 2.5kV 3
Electrical Characteristics UTO 1823 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
120
1823 (Shell size 18, 23x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
8A/150V
per IEC 61984
23
UTO Series | Connector
84
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 87
Square ange
receptacle
IP67 96h UT0W01626PH UT0W01626SH
IP68 & IP69K 96h UT0W01626PH6 UT0W01626SH6
Plug
IP67, IP68 & IP69K 48h UT0W61626PH UT0W61626SH
IP67, IP68 & IP69K 96h UT0W61626PH02(Black) UT0W61626SH02(Black)
Jam nut
receptacle
IP67 48h UT0W71626PH UT0W71626SH
IP68 & IP69K 48h UT0W71626PH6 UT0W71626SH6
IP67 96h UT0W71626PH01 UT0W71626SH01
IP68 & IP69K 96h UT0W71626PH601 UT0W71626SH601
* Other discrimination keying option, see page 182
Layout
Drilling pattern see page 177
1626 (Shell size 16, 26x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 9.5/14 UT016JCS UT016JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 11.5/18 UT016JCSL UT016JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 310/14.5 UT0S16JCS UT0S16JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 313.5/18 UT0S16JCSL UT0S16JCL
Metal cable clamp with strain relief (Fig.5) - 13 UT016AC
Metal shrink boot adaptor (Fig.6) - - UT016AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 6.5/16 UT016LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/16 UT0S16JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/16 UT016JCPGN
UTO Series | Connector
85
Note: all dimensions are in mm
Dimensions
1626 (Shell size 16, 26x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
31.0
24.6
1.6
Male
33 maxi 32.4
25.5 maxi
Ø 30.0
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
27.2
24.6
24.6
Front
mounting
Ø 24.6
Ø 3.2
Rear
mounting
Ø 28.1
28.3
Female
Male
38.134 maxi
33.3
33 maxi
Ø 25.3
17.9
Short version - 63.1
Long version - 74.1
Fig. 1
Short version - 69.1
Long version - 80.1
Fig. 2
Fig. 7
55.0
39.5
Short version - 73.1
Long version - 84.1
Fig. 3
Short version - 83.1
Long version - 94.1
Fig. 4
73.1
Fig. 8
Fig. 6
Ø 30.0
27
Fig. 5
34.0
29.4
Ø 25.8
4A/40V
per IEC 61984
26
UTO Series | Connector
86
Dustcap (Receptacle)
Part number
UT016DCG*
Dustcap (Plug)
Part number
UTG616DCG*
Part number / Neoprene
UTFD15B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
1626 (Shell size 16, 26x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT016DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
87
UL
4A 250V UL94 V-0
CSA
3A 250V UL94 V-0
IEC
4A 40V 1.5kV 3
Electrical Characteristics UTO 1626 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
1
2
3
4
5
6
7
8
9
10
Current (A)
Ambient Operating Temperature (°C)
1626 (Shell size 16, 26x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
4A/40V
per IEC 61984
26
UTO Series | Connector
88
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 91
Square ange
receptacle
IP67 96h UT002028PH UT002028SH
IP68 & IP69K 96h UT002028PH6 UT002028SH6
Plug
IP67, IP68 & IP69K 48h UT062028PH UT062028SH
IP67, IP68 & IP69K 96h UT062028PH02(Black) UT062028SH02(Black)
Jam nut
receptacle
IP67 48h UT072028PH UT072028SH
IP68 & IP69K 48h UT072028PH6 UT072028SH6
IP67 96h UT072028PH01 UT072028SH01
IP68 & IP69K 96h UT072028PH601 UT072028SH601
* Other discrimination keying option, see page 182
Layout
Drilling pattern see page 178
2028 (Shell size 20, 28x#16)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT020JCS UT020JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT020JCSL UT020JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S20JCS UT0S20JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S20JCSL UT0S20JCL
Metal cable clamp with strain relief (Fig.5) - 16.0 UT020AC
Metal shrink boot adaptor (Fig.6) - - UT020AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT020LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S20JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT020JCPGN
UTO Series | Connector
89
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
2028 (Shell size 20, 28x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
14.5
34.75 maxi
29 maxi
36.5
29.3
2.4
Male
33 maxi 38.8
27.5 maxi
Ø 36.5
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
33.5
29.3
29.3
Front
mounting
Ø 30.9
Ø 3.2
Rear
mounting
Ø 34.5
34.8
Female
Male
46.039 maxi
39.7
39 maxi
Ø 31.6
22.7
Short version - 74.8
Long version - 84.6
Fig. 1
Short version - 81.8
Long version - 91.6
Fig. 2
Fig. 7
58.0
47.0
Short version - 88.3
Long version - 98.1
Fig. 3
Short version - 97.3
Long version - 107.1
Fig. 4
84.6
Fig. 8
Fig. 6
Ø 36.5
27
Fig. 5
32.0
35.2
Ø 32.5
7A/150V
per IEC 61984
28
UTO Series | Connector
90
Dustcap (Receptacle)
Part number
UT020DCG*
Dustcap (Plug)
Part number
UTG620DCG*
Part number / Neoprene
UTFD17B
Gasket
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT028DC
2028 (Shell size 20, 28x#16)
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
91
UL
5A 500V UL94 V-0
CSA
3A 500V UL94 V-0
IEC
7A 150V 2.5kV 3
Electrical Characteristics UTO 2028 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
Contacts
2028 (Shell size 20, 28x#16)
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
7A/150V
per IEC 61984
28
UTO Series | Connector
92
OR OR
WITH
OR OR
2030 (Shell size 20, 30x#16)
Connector Part Numbers
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 95
Square ange
receptacle
IP67 96h UT002030PH UT002030SH
IP68 & IP69K 96h UT002030PH6 UT002030SH6
Plug
IP67, IP68 & IP69K 48h UT062030PH UT062030SH
IP67, IP68 & IP69K 96h UT062030PH02(Black) UT062030SH02(Black)
Jam nut
receptacle
IP67 48h UT072030PH UT072030SH
IP68 & IP69K 48h UT072030PH6 UT072030SH6
IP67 96h UT072030PH01 UT072030SH01
IP68 & IP69K 96h UT072030PH601 UT072030SH601
Layout
Drilling pattern see page 178
* Other possible discrimination, see page 180
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT020JCS UT020JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT020JCSL UT020JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S20JCS UT0S20JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S20JCSL UT0S20JCL
Metal cable clamp with strain relief (Fig.5) - 16.0 UT020AC
Metal shrink boot adaptor (Fig.6) - - UT020AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT020LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S20JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT020JCPGN
UTO Series | Connector
93
Dimensions
2030 (Shell size 20, 30x#16)
Note: all dimensions are in mm
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
14.5
34.75 maxi
29 maxi
36.5
29.3
2.4
Male
33 maxi 38.8
27.5 maxi
Ø 36.5
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
33.5
29.3
29.3
Front
mounting
Ø 30.9
Ø 3.2
Rear
mounting
Ø 34.5
34.8
Female
Male
46.039 maxi
39.7
39 maxi
Ø 31.6
22.7
Short version - 74.8
Long version - 84.6
Fig. 1
Short version - 81.8
Long version - 91.6
Fig. 2
Fig. 7
58.0
47.0
Short version - 88.3
Long version - 98.1
Fig. 3
Short version - 97.3
Long version - 107.1
Fig. 4
84.6
Fig. 8
Fig. 6
Ø 36.5
27
Fig. 5
32.0
35.2
Ø 32.5
7A/150V
per IEC 61984
30
UTO Series | Connector
94
Dustcap (Receptacle)
Part number
UT020DCG*
Dustcap (Plug)
Part number
UTG620DCG*
Part number / Neoprene
UTFD17B
Gasket
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT028DC
2030 (Shell size 20, 30x#16)
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
95
Contacts
UL
5A 500V UL94 V-0
CSA
3A 500V UL94 V-0
IEC
7A 150V 2.5kV 3
Electrical Characteristics
2030 (Shell size 20, 30x#16)
UTO 2030 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
7A/150V
per IEC 61984
30
UTO Series | Connector
96
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 99
Square ange
receptacle
IP67 96h UT0W01832PH UT0W01832SH
IP68 & IP69K 96h UT0W01832PH6 UT0W01832SH6
Plug
IP67, IP68 & IP69K 48h UT0W61832PH UT0W61832SH
IP67, IP68 & IP69K 96h UT0W61832PH02(Black) UT0W61832SH02(Black)
Jam nut
receptacle
IP67 48h UT0W71832PH UT0W71832SH
IP68 & IP69K 48h UT0W71832PH6 UT0W71832SH6
IP67 96h UT0W71832PH01 UT0W71832SH01
IP68 & IP69K 96h UT0W71832PH601 UT0W71832SH601
* Other discrimination keying option, see page 182
Layout
Drilling pattern see page 177
1832 (Shell size 18, 32x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 9.5/14 UT018JCS UT018JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 11.5/18 UT018JCSL UT018JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 310/14.5 UT0S18JCS UT0S18JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 313.5/18 UT0S18JCSL UT0S18JCL
Metal cable clamp with strain relief (Fig.5) - 16.0 UT018AC
Metal shrink boot adaptor (Fig.6) - - UT018AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT018LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
36.5/16 UT0S18JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 6.5/16 UT018JCPGN
UTO Series | Connector
97
Note: all dimensions are in mm
Dimensions
1832 (Shell size 18, 32x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
11.3
33.3 maxi
25.2 maxi
33.3
26.9
1.6
Male
33 maxi 35.2
25.5 maxi
Ø 33.3
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
30.3
26.9
26.9
Front
mounting
Ø 27.8
Ø 3.2
Rear
mounting
Ø 31.3
31.8
Female
Male
41.334 maxi
36.5
33 maxi
Ø 28.4
17.9
Short version - 66.1
Long version - 76.6
Fig. 1
Short version - 72.1
Long version - 82.6
Fig. 2
Fig. 7
60.0
46.0
Short version - 76.1
Long version - 86.6
Fig. 3
Short version - 86.1
Long version - 96.6
Fig. 4
77.2
Fig. 8
Fig. 6
Ø 33.3
27
Fig. 5
31.4
35.2
Ø 33.3
4A/50V
per IEC 61984
32
UTO Series | Connector
98
Dustcap (Receptacle)
Part number
UT018DCG*
Dustcap (Plug)
Part number
UTG618DCG*
Part number / Neoprene
UTFD16B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
1832 (Shell size 18, 32x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT018DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
99
UL
4A 250V UL94 V-0
CSA
3A 250V UL94 V-0
IEC
4A 50V 1.5kV 3
Electrical Characteristics UTO 1832 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
2
4
6
8
10
Current (A)
Ambient Operating Temperature (°C)
120
1832 (Shell size 18, 32x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
4A/50V
per IEC 61984
32
UTO Series | Connector
100
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 103
Square ange
receptacle
IP67 96h UT002235PH UT002235SH
IP68 & IP69K 96h UT002235PH6 UT002235SH6
Plug
IP67, IP68 & IP69K 48h UT062235PH UT062235SH
IP67, IP68 & IP69K 96h UT062235PH02(Black) UT062235SH02(Black)
Jam nut
receptacle
IP67 48h UT072235PH UT072235SH
IP68 & IP69K 48h UT072235PH6 UT072235SH6
IP67 96h UT072235PH01 UT072235SH01
IP68 & IP69K 96h UT072235PH601 UT072235SH601
Layout
Drilling pattern see page 178
2235 (Shell size 22, 35x#16)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT022JCS UT022JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT022JCSL UT022JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S22JCS UT0S22JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S22JCSL UT0S22JCL
Metal cable clamp with strain relief (Fig.5) - 19.3 UT022AC
Metal shrink boot adaptor (Fig.6) - - UT022AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT022LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S22JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT022JCPGN
* Other discrimination keying option, see page 182
UTO Series | Connector
101
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
2235 (Shell size 22, 35x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
14.5
34.75 maxi
29 maxi
39.7
31.7
2.4
Male
33 maxi 42
27.5 maxi
39.5
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
36.7
31.7
31.7
Front
mounting
Ø 34.1
Ø 3.2
Rear
mounting
Ø 37.7
37.9
Female
Male
49.239 maxi
42.9
39 maxi
Ø 34.8
22.7
Short version - 77.1
Long version - 88.4
Fig. 1
Short version - 84.1
Long version - 95.4
Fig. 2
Fig. 7
58.0
48.0
Short version - 90.6
Long version - 101.9
Fig. 3
Short version - 99.6
Long version - 110.9
Fig. 4
91.7
Fig. 8
Fig. 6
Ø 39.7
27
Fig. 5
31.0
41.1
Ø 35.7
6A/150V
per IEC 61984
35
UTO Series | Connector
102
Dustcap (Receptacle)
Part number
UT022DCG*
Dustcap (Plug)
Part number
UTG622DCG*
Part number / Neoprene
UTFD18B
Gasket
2235 (Shell size 22, 35x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT022DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
103
UL
5A 500V UL94 V-0
CSA
3A 500V UL94 V-0
IEC
6A 150V 2.5kV 3
Electrical Characteristics UTO 2235 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
2235 (Shell size 22, 35x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
6A/150V
per IEC 61984
35
UTO Series | Connector
104
OR OR
WITH
OR OR
2238 (Shell size 22, 38x#16)
Connector Part Numbers
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 107
Square ange
receptacle
IP67 96h UT002238PH UT002238SH
IP68 & IP69K 96h UT002238PH6 UT002238SH6
Plug
IP67, IP68 & IP69K 48h UT062238PH UT062238SH
IP67, IP68 & IP69K 96h UT062238PH02(Black) UT062238SH02(Black)
Jam nut
receptacle
IP67 48h UT072238PH UT072238SH
IP68 & IP69K 48h UT072238PH6 UT072238SH6
IP67 96h UT072238PH01 UT072238SH01
IP68 & IP69K 96h UT072238PH601 UT072238SH601
Layout
Drilling pattern see page 178
* Other possible discrimination, see page 180
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT022JCS UT022JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT022JCSL UT022JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S22JCS UT0S22JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S22JCSL UT0S22JCL
Metal cable clamp with strain relief (Fig.5) - 19.3 UT022AC
Metal shrink boot adaptor (Fig.6) - - UT022AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT022LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S22JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT022JCPGN
UTO Series | Connector
105
Note: all dimensions are in mm
Dimensions
2238 (Shell size 22, 38x#16)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
14.5
34.75 maxi
29 maxi
39.7
31.7
2.4
Male
33 maxi 42
27.5 maxi
39.5
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
36.7
31.7
31.7
Front
mounting
Ø 34.1
Ø 3.2
Rear
mounting
Ø 37.7
37.9
Female
Male
49.239 maxi
42.9
39 maxi
Ø 34.8
22.7
Short version - 77.1
Long version - 88.4
Fig. 1
Short version - 84.1
Long version - 95.4
Fig. 2
Fig. 7
58.0
48.0
Short version - 90.6
Long version - 101.9
Fig. 3
Short version - 99.6
Long version - 110.9
Fig. 4
91.7
Fig. 8
Fig. 6
Ø 39.7
27
Fig. 5
31.0
41.1
Ø 35.7
6A/150V
per IEC 61984
38
UTO Series | Connector
106
2238 (Shell size 22, 38x#16)
Dustcap (Receptacle)
Part number
UT022DCG*
Dustcap (Plug)
Part number
UTG622DCG*
Part number / Neoprene
UTFD18B
Gasket
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT022DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
107
2238 (Shell size 22, 38x#16)
UL
5A 500V UL94 V-0
CSA
3A 500V UL94 V-0
IEC
6A 150V 2.5kV 3
Electrical Characteristics UTO 2238 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
6A/150V
per IEC 61984
38
UTO Series | Connector
108
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 111
Square ange
receptacle
IP67 96h UT0W02041PH UT0W02041SH
IP68 & IP69K 96h UT0W02041PH6 UT0W02041SH6
Plug
IP67, IP68 & IP69K 48h UT0W62041PH UT0W62041SH
IP67, IP68 & IP69K 96h UT0W62041PH02(Black) UT0W62041SH02(Black)
Jam nut
receptacle
IP67 48h UT0W72041PH UT0W72041SH
IP68 & IP69K 48h UT0W72041PH6 UT0W72041SH6
IP67 96h UT0W72041PH01 UT0W72041SH01
IP68 & IP69K 96h UT0W72041PH601 UT0W72041SH601
* Other discrimination keying option, see page 182
Layout
Drilling pattern see page 178
2041 (Shell size 20, 41x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT020JCS UT020JC
Cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT020JCSL UT020JCL
Shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S20JCS UT0S20JC
Shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S20JCSL UT0S20JCL
Metal cable clamp with strain relief (Fig.5) - 16.0 UT020AC
Metal shrink boot adaptor (Fig.6) - - UT020AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT020LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S20JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT020JCPGN
UTO Series | Connector
109
Note: all dimensions are in mm
Dimensions
2041 (Shell size 20, 41x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
14.5
34.75 maxi
29 maxi
36.5
29.3
2.4
Male
33 maxi 38.8
27.5 maxi
Ø 36.5
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
33.5
29.3
29.3
Front
mounting
Ø 30.9
Ø 3.2
Rear
mounting
Ø 34.5
34.8
Female
Male
46.039 maxi
39.7
39 maxi
Ø 31.6
22.7
Short version - 74.8
Long version - 84.6
Fig. 1
Short version - 81.8
Long version - 91.6
Fig. 2
Fig. 7
58.0
47.0
Short version - 88.3
Long version - 98.1
Fig. 3
Short version - 97.3
Long version - 107.1
Fig. 4
84.6
Fig. 8
Fig. 6
Ø 36.5
27
Fig. 5
32.0
35.2
Ø 32.5
8A/80V
per IEC 61984
41
UTO Series | Connector
110
Dustcap (Receptacle)
Part number
UT020DCG*
Dustcap (Plug)
Part number
UTG620DCG*
Part number / Neoprene
UTFD17B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
2041 (Shell size 20, 41x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT020DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
111
UL
3A 250V UL94 V-0
CSA
2A 250V UL94 V-0
IEC
8A 80V 1.5kV 3
Electrical Characteristics UTO 2041 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
1
2
3
4
5
6
7
8
9
10
Current (A)
Ambient Operating Temperature (°C) 120
2041 (Shell size 20, 41x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
8A/80V
per IEC 61984
41
UTO Series | Connector
112
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 115
Square ange
receptacle
IP67 96h UT002448PH UT002448SH
IP68 & IP69K 96h UT002448PH6 UT002448SH6
Plug
IP67, IP68 & IP69K 48h UT062448PH UT062448SH
IP67, IP68 & IP69K 96h UT062448PH02(Black) UT062448SH02(Black)
Jam nut
receptacle
IP67 48h UT072448PH UT072448SH
IP68 & IP69K 48h UT072448PH6 UT072448SH6
IP67 96h UT072448PH01 UT072448SH01
IP68 & IP69K 96h UT072448PH601 UT072448SH601
* Other discrimination keying option, see page 182
Drilling pattern see page 183
Layout
2448 (Shell size 24, 48x#16)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT024JCS UT024JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT024JCSL UT024JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S24JCS UT0S24JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S24JCSL UT0S24JCL
Metal cable clamp with strain relief (Fig.5) - 19.3 UT024AC
Metal shrink boot adaptor (Fig.6) - - UT024AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT024LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S24JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT024JCPGN
UTO Series | Connector
113
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Note: all dimensions are in mm
Dimensions
2448 (Shell size 24, 48x#16)
Backshells (for Mated Connector Length: See Page 153)
Female
Male
15.3
34.75 maxi
29 maxi
42.8
34.9
2.4
Male
33 maxi 45.05
27.5 maxi
Ø 42.6
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
39.9
34.9
34.9
Front
mounting
Ø 37.3
Ø 3.9
Rear
mounting
Ø 40.9
41.2
Female
Male
53.441 maxi
46.0
41 maxi
Ø 38.0
23.6
Short version - 82.4
Long version - 92.4
Fig. 1
Short version - 89.4
Long version - 99.4
Fig. 2
Fig. 7
67.0
54.5
Short version - 95.9
Long version - 105.9
Fig. 3
Short version - 104.9
Long version - 114.9
Fig. 4
91.7
Fig. 8
Fig. 6
Ø 42.9
27
Fig. 5
31.0
42.4
Ø 38.8
6A/160V
per IEC 61984
48
UTO Series | Connector
114
Dustcap (Receptacle)
Part number
UT024DCG*
Dustcap (Plug)
Part number
UTG624DCG*
Part number / Neoprene
UTFD19B
Gasket
2448 (Shell size 24, 48x#16)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT024DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Part number
RX2025GE1
Extraction Tool #16
See page 182 for more information
Part number / Polyamide 6.6
SMSPKE0
Dummy Contact #16
+=
Handle Head Complete set
Contacts Contact size Part number
of head
RM/RC 28M1K(1)
Standard contacts
#16
Ø 1.6mm
S16RCM20*
RM/RC 24M9K(1) S16RCM20*
RM/RC 20M13K(1) S16RCM20*
RM/RC 20M12K(1) S16RCM20*
RM/RC 16M23K(1) S16RCM16*
RM/RC 14M30K(1) S16RCM14*
SM/SC 24ML1TK6(1) S16SCM20*
SM/SC 20ML1TK6(1) S16SCM20*
SM/SC 16ML1TK6(1) S16SCML1*
SM/SC 14ML1TK6(1) S16SCML1*
SM/SC 16ML11TK6(1) S16SCML11*
RMDXK10D28K
Coaxial contacts
M10S1J
with die set &
stop bushing
see page
173 to 174
RCDXK1D28K
RM/RC DX60xxD28K
RM/RC DXK10D28 +
york090
RM/RC DX60xxD28
C
i
T
l
i
C
r
i
mp
T
oo
li
ng
(
without Shandles
)
(1): Example of plating, for other plating options see page 129
* Heads to be used with handle PN: SHANDLES
UTO Series | Connector
115
UL
5A 500V UL94 V-0
CSA
3A 500V UL94 V-0
IEC
6A 160V 2.5kV 3
Electrical Characteristics UTO 2448 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
1.31mm²
Current use Limited use Not recommended use
1200 20 40 60 80 100
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
2448 (Shell size 24, 48x#16)
Contacts
Note: all dimensions are in mm(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20ML1TK6
(3): For dimensions see page 132
#16 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
30-28 RM28M1K(1) RC28M1K(1) 0.55 1.00
26-24 RM24M9K(1) RC24M9K(1) 0.80 1.60
22-20 RM20M13K(1) RC20M13K(1) 1.15 1.80
22-20 RM20M12K(1) RC20M12K(1) 1.15 2.20
20-16 RM16M23K(1) RC16M23K(1) 1.80 3.20
16-14 RM14M30K(1) RC14M30K(1) 2.30 3.20
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24M1TK6(1)(2) SC24M1TK6(1)(2) - 0.90-1.60
22-20 SM20M1TK6(1)(2) SC20M1TK6(1)(2) - 1.20-2.10
18-16 SM16M1TK6(1)(2) SC16M1TK6(1)(2) - 3.20
18-16 SM16M11TK6(1)(2) SC16M11TK6(1)(2) - 3.00
14 SM14M1TK6(1)(2) SC14M1TK6(1)(2) - 3.20
PCB
Machined (3) -RM20M12E8K(1) RC20M12E84K(1) --
Coaxial
Cable Multipiece
see pages
131,
168 to 174
RMDXK10D28 RCDXK1D28 --
Cable Monocrimp RMDX60xxD28 RCDX60xxD28 --
Twisted pair Multipiece RMDXK10D28 +
york090
RCDXK1D28 +
york090 --
Twisted pair Monocrimp RMDX60xxD28 RCDX60xxD28 --
6A/160V
per IEC 61984
48
UTO Series | Connector
116
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 119
Square ange
receptacle
IP67 96h UT0W02255PH UT0W02255SH
IP68 & IP69K 96h UT0W02255PH6 UT0W02255SH6
Plug
IP67, IP68 & IP69K 48h UT0W62255PH UT0W62255SH
IP67, IP68 & IP69K 96h UT0W62255PH02(Black) UT0W62255SH02(Black)
Jam nut
receptacle
IP67 48h UT0W72255PH UT0W72255SH
IP68 & IP69K 48h UT0W72255PH6 UT0W72255SH6
IP67 96h UT0W72255PH01 UT0W72255SH01
IP68 & IP69K 96h UT0W72255PH601 UT0W72255SH601
* Other discrimination keying option, see page 182
Drilling pattern see page 183
Layout
2255 (Shell size 22, 55x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT022JCS UT022JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT022JCSL UT022JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S22JCS UT0S22JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S22JCSL UT0S22JCL
Metal cable clamp with strain relief (Fig.5) - 19.3 UT022AC
Metal shrink boot adaptor (Fig.6) - - UT022AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 9/21 UT022LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
39/21 UT0S22JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 9/21 UT022JCPGN
UTO Series | Connector
117
Note: all dimensions are in mm
Dimensions
2255 (Shell size 22, 55x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
14.5
34.75 maxi
29 maxi
39.7
31.7
2.4
Male
33 maxi 42
27.5 maxi
39.5
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
36.7
31.7
31.7
Front
mounting
Ø 34.1
Ø 3.2
Rear
mounting
Ø 37.7
37.9
Female
Male
49.239 maxi
42.9
39 maxi
Ø 34.8
22.7
Short version - 77.1
Long version - 88.4
Fig. 1
Short version - 84.1
Long version - 95.4
Fig. 2
Fig. 7
58.0
48.0
Short version - 90.6
Long version - 101.9
Fig. 3
Short version - 99.6
Long version - 110.9
Fig. 4
91.7
Fig. 8
Fig. 6
Ø 39.7
27
Fig. 5
31.0
41.1
Ø 35.7
3A/80V
per IEC 61984
55
UTO Series | Connector
118
Dustcap (Receptacle)
Part number
UT022DCG*
Dustcap (Plug)
Part number
UTG622DCG*
Part number / Neoprene
UTFD18B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
2255 (Shell size 22, 55x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT024DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
119
UL
3A 250V UL94 V-0
CSA
2A 250V UL94 V-0
IEC
3A 80V 1.5kV 3
Electrical Characteristics UTO 2255 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
1
2
3
4
5
6
7
8
9
10
Current (A)
Ambient Operating Temperature (°C)
120
2255 (Shell size 22, 55x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see page 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
3A/80V
per IEC 61984
55
UTO Series | Connector
120
OR OR
WITH
OR OR
Contact type Connector type Sealing Salt spray Part number*
Male insert Female insert
Contacts
supplied separately
see page 123
Square ange
receptacle
IP67 96h UT0W02461PH UT0W02461SH
IP68 & IP69K 96h UT0W02461PH6 UT0W02461SH6
Plug
IP67, IP68 & IP69K 48h UT0W62461PH UT0W62461SH
IP67, IP68 & IP69K 96h UT0W62461PH02(Black) UT0W62461SH02(Black)
Jam nut
receptacle
IP67 48h UT0W72461PH UT0W72461SH
IP68 & IP69K 48h UT0W72461PH6 UT0W72461SH6
IP67 96h UT0W72461PH01 UT0W72461SH01
IP68 & IP69K 96h UT0W72461PH601 UT0W72461SH601
* Other discrimination keying option, see page 182
Layout
Drilling pattern see page 183
2461 (Shell size 24, 61x#20)
Connector Part Numbers
Backshells
Backshell type Shielding Cable range
(Ø mm) min/max
Part number
Short version Long version
Short cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.1) - 11.5/18 UT024JCS UT024JC
Short cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.2) - 15/24 UT024JCSL UT024JCL
Short shielded cable gland with strain relief nut
for water protected applications (IP68 & IP69K) (Fig.3) 313.5/18 UT0S24JCS UT0S24JC
Short shielded cable gland with large strain relief nut
for water protected applications (IP68 & IP69K) (Fig.4) 317/24 UT0S24JCSL UT0S24JCL
Metal cable clamp with strain relief (Fig.5) - 20.6 UT024AC
Metal shrink boot adaptor (Fig.6) - - UT024AD
Metal right angle cable clamp with strain relief nut (Fig.7)
- 17/30 UT024LPGN
Shielded cable clamp with plastic strain relief nut (Fig.8)
317/29.5 UT0S24JCPGN
Cable clamp with plastic strain relief nut (Fig.8)
- 17/29.5 UT024JCPGN
UTO Series | Connector
121
Note: all dimensions are in mm
Dimensions
2461 (Shell size 24, 61x#20)
Plug - UTO6 Square Flange - UTO
0
Jam Nut - UTO7 Panel Cut Out
Backshells (for Mated Connector Length: See Page 153)
Female
Male
15.3
34.75 maxi
29 maxi
42.8
34.9
2.4
Male
33 maxi 45.05
27.5 maxi
Ø 42.6
Female
Jam nut receptacle - UTO7
Jam nut receptacle - UTO
0
39.9
34.9
34.9
Front
mounting
Ø 37.3
Ø 3.9
Rear
mounting
Ø 40.9
41.2
Female
Male
53.441 maxi
46.0
41 maxi
Ø 38.0
23.6
Short version - 82.4
Long version - 92.4
Fig. 1
Short version - 89.4
Long version - 99.4
Fig. 2
Fig. 7
67.0
54.5
Short version - 95.9
Long version - 105.9
Fig. 3
Short version - 104.9
Long version - 114.9
Fig. 4
91.7
Fig. 8
Fig. 6
Ø 42.9
27
Fig. 5
31.0
42.4
Ø 38.8
3A/80V
per IEC 61984
61
UTO Series | Connector
122
Dustcap (Receptacle)
Part number
UT024DCG*
Dustcap (Plug)
Part number
UTG624DCG*
Part number / Neoprene
UTFD19B
Gasket Crimp Tooling (without Shandles)
Contacts Contact size Part number
of head
RM/RC 24W3K(1)
Standard contacts
#20
Ø 1mm
S20RCM*
RM/RC 20W3K(1) S20RCM*
RM/RC 18W3K(1) S20RCM*
SM/SC 24WL3(1)(2) S20SCM20*
SM/SC 20WL3(1)(2) S20SCM20*
(1): Example of plating, for other plating options see page 129
(2): loose contact
* Heads to be used with handle PN: SHANDLES
+=
Handle Head Complete set
2461 (Shell size 24, 61x#20)
Accessories and Tooling
* For dustcap without chain, skip "G", e.g. UT024DC
Tool KitHandle (without Head)
Part number
TOOLKIT
Part number
SHANDLES
Extraction Tool #20
Part number
RX20D44
UTO Series | Connector
123
UL
3A 250V UL94 V-0
CSA
2A 250V UL94 V-0
IEC
3A 80V 1.5kV 3
Electrical Characteristics UTO 2461 Derating Curves
Test
conditions
Contact used:
Machined contacts
Wires used:
0.518mm²
Current use Limited use Not recommended use
0 20 40 60 80 100
0
1
2
3
4
5
6
7
8
9
10
Current (A)
Ambient Operating Temperature (°C) 120
2461 (Shell size 24, 61x#20)
Contacts
(1): Example of plating, for other plating options see page 129
(2): For loose piece contact packaging, place "L" in part number. Example: SM20WL3TK6
(3): For dimensions see v 132
Note: all dimensions are in mm
#20 Contact type AWG Part number Max
wire Ø
Max
insulator Ø
Male Female
Crimp
Machined
26-24 RM24W3K RC24W3K 0.80 1.60
22-20 RM20W3K RC20W3K 1.15 1.60
20-18 RM18W3K RC18W3K 1.30 2.10
Stamped & formed reeled contacts
See note (2) for loose piece
26-24 SM24W3TK6(1)(2) SC24W3TK6(1)(2) - 0.90-1.60
26-24 SM24W3S26(1)(2) SC24W3S25(1)(2) - 0.90-1.60
22-20 SM20W3TK6(1)(2) SC20W3TK6(1)(2) - 1.20-2.10
22-20 SM20W3S26(1)(2) SC20W3S25(1)(2) - 1.20-2.10
PCB
Machined (3) -RMW5016K RCW5016K --
3A/80V
per IEC 61984
61
UTO SERIES
© 2013 SOURIAU - SOURIAU is a registered trademark
125
Description ............................................................................................................... 126
Contact Plating Selector Guide ................................................................................ 127
Contact Selector Guide ............................................................................................ 128
Packaging ................................................................................................................. 128
Crimp Contacts ........................................................................................................ 129
#16 Coaxial Contacts ............................................................................................... 131
PCB Contacts ........................................................................................................... 132
Fiber Optic Contacts ................................................................................................ 133
Contacts
UTO Series
126
Contacts
Description
The UTO series is delivered without contacts and offers the unique feature to use the same style contact in any layout with the same active part
size (i.e. #20, #16, #12, etc.). This provides our customers with an easy solution to buy only one type of contact to equip all their connectors
even if housings/shell sizes are different.
This provides the benefit of standardization and subsequent reduced inventory costs. In addition, it eliminates the need for added tooling and
simplifies the assembly process. SOURIAU contacts are designed for simple snap-in installation and further eliminate the need for insertion
tooling.
In addition to the below “crimp” style contact options, the UTO series can also be equipped with PCB contacts.
Crimp contacts are available in different versions:
• stamped & formed • coaxial • fiber optic
• machined
UTO Series | Contacts
127
Contact Plating Selector Guide
Once the contact size has been selected, the next step is to decide on which type to use. SOURIAU offers two main types of electrical contacts:
• Machined
• Stamped & Formed
Machined contacts are generally chosen as a better solution for power applications or when lower quantities are needed.
Stamped & formed contacts offer the ability to be crimped automatically which makes them more suitable for high volume production
applications.
The next decision to make is: What plating should I choose?
The graph below can help guide you to plating recommendations based on application, mating cycles and current/voltage needs.
Note: do not mix different plating (i.e. tin plated pin contacts with gold plated socket contacts).
250
100
0.4μm of gold
min
Gold ash
Silver
Tin
5mA
5mV
Contact
size
#20 #12
#16 #8
Vibration
Number of
cycles
Current /
Voltage
UTO Series | Contacts
Contacts
128
Due to the wide variety of applications, contact packaging is offered for small series (bulk package) and high volume production (reeled contacts):
Size contacts #20 & #16
• 100 pieces bulk package
(machined contacts)
• 50 pieces bulk package
(machined contacts)
• 25 pieces loose package
(stamped & formed
contacts)
• 1000 pieces
bulk package
(machined contacts)
• 5000 pieces reeled
(machined contacts)
• 3000 pieces reeled
(stamped & formed
contacts)
Size contacts #12 & #8
Packaging
Electrical characteristics: contact resistance
#20
Ø1mm
Machined < 6mΩ
Stamped & formed < 6mΩ
#16
Ø1.6mm
Machined < 3mΩ
Stamped & formed < 6mΩ
#12
Ø2.4mm Machined < 5mΩ
#8
Ø3.6mm Machined < 5mΩ
Available plating options
A2 Ni + 2 Ag
JGold ash over 2 Ni
KMin 0.4 gold over 2 Ni
S31 Active part: Gold ash over Ni
Crimp area: Nickel
S18
Active part: 0.75 gold min over 2 Ni
Crimp area: 1.3µ tin over Ni
Other: Nickel
S25
S26
Active part: 0.75 Au over Ni
Crimp area: ash Au over Ni
TK6 2-5 Sn pre-plated
D70 Superseded by S31
S6 Superseded by S18
Other platings on request (contact supplied separately)
TT: 2m Ni mini all over +
3 to 5 m Sn all over
D28 0.75 gold over Ni
Contacts supplied separately
Contact Selector Guide
UTO Series | Contacts
129
Crimp contacts
(1) contact reeled (2) loose contact
Exemple: RM24W3K - Size #20, Machined, AWG24 wire.
Standard Version
Contact
size Type
Wire size Part number Max
wire Ø
Max
insulator Ø
Available
plating
see page 128
AWG mm² Male Female
#20
Ø1 mm
Machined 26-24 0.13-0.20 RM24W3K RC24W3K 1.58 max K
Stamped &
Formed 26-24 0.13-0.25
SM24W3-(1) SC24W3-(1)
0.89-1.58
TK6
S25 (female)
S26 (male)
SM24WL3-(2) SC24WL3-(2)
Machined 22-20 0.32-0.52 RM20W3K RC20W3K 1.58 max K
Stamped &
Formed 22-20 0.35-0.5
SM20W3-(1) SC20W3-(1)
1.17-2.08
TK6
S25 (female)
S26 (male)
SM20WL3-(2) SC20WL3-(2)
Machined 20-18 0.50-0.93 RM18W3K RC18W3K 2.10 max K
#16
Ø1.6
mm
Machined 30-28 0.05-0.08 RM28M1- RC28M1- 0.55 1.1 K, J
Machined 26-24 0.13-0.2 RM24M9- RC24M9- 0.8 1.6 K, J
Stamped &
Formed 26-24 0.13-0.25 SM24M1-(1)
SM24ML1-(2)
SC24M1-(1)
SC24ML1-(2) 0.89-1.28 Insulation
grip S31, S18, TK6
Machined 22-20 0.32-0.52 RM20M13- RC20M13- 1.18 1.8 K, J
RM20M12- RC20M12- 2.2
Stamped &
Formed 22-20 0.35-0.5 SM20M1-(1)
SM20ML1-(2)
SC20M1-(1)
SC20ML1-(2) 1.17-2.08 Insulation
grip S31, S18, TK6
Machined 20-16 0.52-1.5 RM16M23- RC16M23- 1.8 3.2 K, J
Stamped &
Formed 18-16 0.8-1.5 SM16M1-(1)
SM16ML1-(2)
SC16M1-(1)
SC16ML1-(2) 3.0
No insulation
grip
S31, S18, TK6
Stamped &
Formed 18-16 0.8-1.5 SM16M11-(1)
SM16ML11-(2)
SC16M11-(1)
SC16ML11-(2) 2.0-3.0 Insulation
grip S31, S18, TK6
Machined 16-14 1.5-2.5 RM14M30- RC14M30- 2.28 3.2 K, J
Stamped &
Formed 14 2.0-2.5 SM14M1-(1)
SM14ML1-(2)
SC14M1-(1)
SC14ML1-(2) 3.2
No insulation
grip
S31, S18, TK6
#12
Ø2.4
mm
Machined
22 0.13-0.4 82911457N- 82911456-
- 4.9 A, K
20 0.5 82911459N- 82911458-
18 0.75-1.0 82911461N- 82911460-
16 1.5 82911463N- 82911462-
14 2.5 82911465N- 82911464-
12 4 82911467N- 82911466-
#8
Ø3.6
mm
Machined
16 1.5 82913601A 82913600A
- 6.5 A
14 2.5 82913603A 82913602A
12 4 82913605A 82913604A
10 6.0 82913607A 82913606A
8 10.0 82913609A 82913608A
Note: all dimensions are in mm
UTO Series | Contacts
Contacts
130
Crimp contacts (continued)
Contact 1
Contact 2
Standard male
contact
Standard female
contact Longer male contact
Standard male
contact
Standard female
contact FMLB
Shorter female
contact LMFB
First Mate Last Break contacts should be
chosen only if the cavity is not marked with
the ground symbol. For cavities marked
with the ground symbol, standard contacts
will ful ll the same role as a rst mate, last
break contact used in a standard cavity.
Ground symbol
How to make FMLB / LMFB onnection
First Mate Last Break Contacts
Contact
size Type Wire size Part number Max
wire Ø
(mm)
Max
insulator Ø
(mm)
Color band Available
plating
see p. 128
AWG mm² Male Female Front Rear
#16
Ø1.6 mm
Longer male
contact
(+1mm)
Machined
30-28 0.05-0.08 RM28M1GE1-
-
0.55 1.1 - Red
K or J
26-24 0.13-0.2 RM24M9GE1- 0.8 1.6 Red Red
22-20 0.32-0.52 RM20M13GE1- 1.18 1.8 Black Red
RM20M12GE1- 2.2 Blue Red
20-16 0.52-1.5 RM16M23GE1- 1.8 3.2 - Red
16-14 1.5-2.5 RM14M30GE1- 2.28 - - Red
#16
Ø1.6 mm
Shorter
female contact
(-0.7mm)
Machined
30-28 0.05-0.08
-
RC28M1GE7- 0.55 1.1 - Blue
K or J
26-24 0.13-0.2 RC24M9GE7- 0.8 1.6 Red Blue
22-20 0.32-0.52 RC20M13GE7- 1.18 1.8 Black Blue
RC20M12GE7- 2.2 Blue Blue
20-16 0.52-1.5 RC16M23GE7- 1.8 3.2 - Blue
16-14 1.5-2.5 RC14M30GE7- 2.28 - - Blue
o
nt
Re
Note: all dimensions are in mm
UTO Series | Contacts
131
#16 coaxial contacts
SOURIAU provides 2 types of coaxial contacts suitable for 50 or 75Ω, coaxial cable or twisted pair cable.
Monocrimp coaxial contact
• The monocrimp one-piece coaxial contacts offer high reliability plus the econo-
mic advantage of a 95% reduction in installation time over conventional assembly
methods.
• This economy is achieved by simultaneously crimping both the inner conductor
and outer braid or drain wire.
Multipiece crimp coaxial contact
• The inner conductor and outer braid is crimped individually.
• The thermoplastic insulating bushing in the outer body is designed to accept
and permanently retain the inner contact.
• An outer ferrule is used to connect the braid to the outer contact and provide
cable support to ensure against bending and vibration.
Suitable for Coaxial cable or Twisted cable
• For jacket diameter from 1.78 to 3.05mm
Inner conductor up to 2.44mm diameter
• For jacket diameter from 0.64 to 1.45mm
Inner conductor from AWG30 to AWG24
Coaxial Contact Range
Contacts for coaxial cable summary
Contact type
Contact range Contact part number with
cable combination Cabling notice
Male contact Female contact
Multipiece RMDXK10D28 RCDXK1D28 See page 168 See pages 172 & 173
Monocrimp RMDX60xxD28 RCDX60xxD28 See page 174
Contacts for twisted pairs cable summary
Contact type Contact range Contact part number with
cable combination Cabling notice
Male contact Female contact
Multipiece RMDXK10D28
+ YORK090
RCDXK1D28
+ YORK090 See page 169 See page 170
Monocrimp RMDX60xxD28 RCDX60xxD28 See page 171
UTO Series | Contacts
Contacts
132
PCB contacts
PCB Contacts
PCB soldering
The UTO series can be used in a wave soldering process, but not re ow soldering process.
All high temperature processes are prohibited.
Contact size Type Part number Plating
see page 128
Male Female
#20
Ø1mm
Short version RMW50A7K RCW50A7K
K
Long version RMW5016K RCW5016K
#16
Ø1.6mm
Short version RM20M12E8- RC20M12E8-
K or J
Long version RM20M12E83- RC20M12E83-
RC20M12E84-
#8
Ø3.6mm -82911685NPC 82911684NPC 2 m Ni
82911685NAPC 82911684NAPC 2 m Ni + 0.6 m Ag
Nominal length G (mm)
Dimension of dipsolder contacts out of connector
(contacts to be ordered separately).
G
* Plating indication see page 128
UTO
7 and
UTOW
7
Connector size
Pin contact Socket contact
RM20M
12E8K*
RM20M
12E83K*
RMW
50A7K
RMW
5016K
RC20M
12E8K*
RC20M
12E83K*
RC20M
12E84K*
RCW
50A7K
RCW
5016K
10 4.1 9.2 9.51 10.41 4.65 8.5 4.65 2.4 3.04
12 4.4 9.2 9.51 10.41 3.3 8.5 4.65 2.4 3.04
14 4.1 9.2 9.51 10.41 3.3 8.5 5.35 2.4 3.04
16 4.1 9.2 9.51 10.41 3.3 8.5 4.65 2.4 3.04
18 - 9.2 5 6 - - 4.65 - -
20 - 4.85 5 6 - - - - -
22 - 4.85 5 6 - - - - -
24 - 3.35 3.6 4.6 - - - - -
UTO
0 and UTOW0
Connector size
Pin contact Socket contact
RM20M
12E8K*
RM20M
12E83K*
RMW
50A7K
RMW
5016K
RC20M
12E8K*
RC20M
12E83K*
RC20M
12E84K*
RCW
50A7K
RCW
5016K
10 4.1 9.2 9.51 10.41 4.65 8.5 4.65 2.4 3.04
12 4.4 9.2 9.51 10.41 3.3 8.5 4.65 2.4 3.04
14 4.1 9.2 9.51 10.41 3.3 8.5 5.35 2.4 3.04
16 4.1 9.2 9.51 10.41 3.3 8.5 4.65 2.4 3.04
18 - 9.2 5 6 - - 4.65 - -
20 - 4.85 5 6 - - - - -
22 - 4.85 5 6 - - - - -
24 - 3.35 3.6 4.6 - - - - -
Note: all dimensions are in mm
UTO Series | Contacts
133
Fiber optic contacts
Size 16 fiber optic contacts for UTO and other TRIM TRIO® connectors
Size 16 fiber optic contacts are designed for the integration of optical links in UTO and other TRIM TRIO® cable connectors.
The Fiber optic contacts are designed to accommodate:
• Plastic Optical Fiber (POF) 1 mm core and 2.2 mm jacket
Typical features and benefits are:
• Socket contact is spring loaded to avoid any air gap between the two optical faces.
• Low insertion loss is provided by high precision pieces.
• Single jumpers, multiway harness and active device housings can be supplied regarding customer requirement.
Performance
• Fiber type: ........................................................................................................POF
• Wave length: .................................................................................................. 650 nm
• Optical insertion loss (typ.): ......................................................................... 2 dB max.
• Jacketed external diameter: ...........................................................................2.2mm
• Temperature range: .................................................................................-25°C to +70°C
• Cable retention: ................................................................................................49N
• Mating cycles without cleaning: ........................................................................ 50
• Max. mating cycles: .......................................................................................... 500
Construction
• Contact body: Copper alloy
Connector accommodation
Any TRIM TRIO® size 16 contact can be used in any contact position in any connector in the TRIM TRIO® size 16 interconnection system:
UTP, UTS, UTG, UTO.
Description
Technical Characteristics
UTO Series | Contacts
Contacts
134
Fiber optic contacts (continued)
POF Contact (Plastic Optical Fiber)
Ordering Information
Part numbers Descriptions
80WD0005 Stripping tool
80WD0025 Automatic stripping tool for Ø 0.5 mm,
0.6 mm, 0.7 mm & 3.8 mm
80WM0006 Ruler
80WP0005 Polishing plate
80WP0013 Non slip base (to hold the polishing plate)
80WP0014 Polishing disk (grain size 9µm)
80WP0018 Polishing tool
80WP0019 Polishing disk (grain size 30µm)
80WS0002 Crimping plier
STANDARD TOOLING KIT - P/N 80MS0004
The
standard tooling kit
is made of the part numbers below
that can be ordered separately as well.
Part numbers Descriptions
80WG0010 Needle
80WG0015 Capsule
80WG0016 Syringe
80WN0005 Dry air spray
80WN0006 Optical paper
80WN0012 Dropper bottle
80WN0008 Wiping solvent
SPECIFIC TOOLING LIST - Can only be ordered separately
POF Contacts (Plastic Optical Fiber)
Male contact ........................................
RMPOF1000
Female contact ..................................
RCPOF1000B
UTO Series | Contacts
135
UTO Series | Contacts
Contacts
UTO SERIES
© 2013 SOURIAU - SOURIAU is a registratred trademark
137
Tooling .................................................................................................................... 139
Crimping Instructions ............................................................................................. 140
Handle & Interchangeable Heads .......................................................................... 142
Extraction Tools ...................................................................................................... 143
Dimensions Overmoulded Harnesses .................................................................... 143
Assembly Instructions ............................................................................................. 144
Mated Connector Length ....................................................................................... 153
Rated Current & Working Voltage .......................................................................... 155
Shielding Effectiveness/Corrosion .......................................................................... 156
UL94 + UL1977 ....................................................................................................... 157
IEC 61984 & IP Codes Explained ........................................................................... 160
IEC 61140 Explained .............................................................................................. 162
What is NEMA Rating ? .......................................................................................... 163
Ethernet for the Layman ......................................................................................... 164
Technical Information
UTO Series
UTO Series | Technical Information
138
SOURIAU has been working in partnership with Mecal for many years. With sales of ces located in all major
industrial regions of the world, the combined strengths of both organisations has resulted in a truly global
solution to all your production tooling needs.
Mecal sales network:
Mecal is a leader in manufacturing tooling for
crimping terminals over a stripped wire.
Established in 1976, Mecal has become one of the
world's leading companies dedicated to the design
and manufacture of semi automatic production tools
for strip fed, open barrel crimp terminals, serving the
Automotive, Telecom and Datacom industries.
The extreme environment interconnect specialist
“from deep sea to deep space”.
SOURIAU designs, manufactures and markets high
performance interconnect solutions for severe
environments dedicated to the aerospace, defense,
light and heavy industry markets.
Mini Applicator Stripper Presses
www.mecal.net/eng/retevendita.php
Automatic Crimping Tools
UTO Series | Technical Information
139
Tooling
Contact size Part number Tool with separate locator Extraction tools
Hand tool Positioner + locator setting
#12
Ø 2.4mm
82911457N* / 82911456*
M317 VGE10077A
1-2
51060210924
82911459N* / 82911458* 2
82911461N* / 82911460* 2
82911463N* / 82911462* 3
82911465N* / 82911464* 3
82911467N* / 82911466* 4
#8
Ø 3.6mm
82913601A / 82913600A
M317 VGE10078A
3
51060210936
82913603A / 82913602A 3
82913605A / 82913604A 4
82913607A / 82913606A 5
82913609A / 82913608A 6/7
Speci c contacts (First mate Last break contacts)
Contact size Part number* Hand tools
(SHANDLES) head
Tool with separate locator Extraction tools
Hand tool Positioner + locator setting
#16
Ø 1.6mm
Longer RM
contact
RM28M1GE1K
S16RCM20
RX2025GE1
RM24M9GE1K
RM20M13GE1K
RM16M23GE1K
RM20M12GE1K S16RCM16 MH860 MH86186 6/8
RM14M30GE1K S16RCM14
#16
Ø 1.6mm
Shorter RC
contact
RC28M1GE7K
S16RCM20 MH860 MH86164G
4/6
RC24M9GE7K 5/6
RC20M13GE7K
RC20M12GE7K 5/7
RC16M23GE7K S16RCM16 6/8
RC14M30GE7K S16RCM14 M317 UH25 3
Coaxial contacts
See coax contacts details on page 131 and cabling notice pages 170 to 174.
Crimp Tool Table
Standard contacts
(1) loose contact
Contact size Part number Head Handles Extraction tools
#20
Ø 1mm
RM/RC 24W3K
S20RCM
SHANDLES
(endurance of
SHANDLES tool = 5,000 cycles)
RX20D44
RM/RC 20W3K
RM/RC 18W3K
SM 24WL3S*(1)
SC 24WL3S*(1) S20SCM20
SM/SC 20WL3S*(1)
#16
Ø 1.6mm
RM/RC 28M1*
S16RCM20
RX2025GE1
RM/RC 24M9*
RM/RC 20M13*
RM/RC 20M12*
RM/RC 16M23* S16RCM16
RM/RC 14M30* S16RCM14
SM/SC 24ML1* S16SCM20
SM/SC 20ML1*
SM/SC 16ML1* S16SCML1
SM/SC 14ML1*
SM/SC 16ML11* S16SCML11
* see page 130 for plating options and other contact details
* see page 129 for plating options and other contact details
Technical Information
UTO Series | Technical Information
140
Crimping Instructions
Wire Stripping Crimp Version
Part number Stripping
length L
(mm)
Male Female
Machined contact #20 - Ø 1mm
RM24W3- / RM20W3-
RM18W3-
RC24W3- / RC20W3-
RC18W3- 4.8
#16 - Ø 1.6mm
RM28M1- / RM24M9-
RM20M13- / RM20M12-
RC28M1- / RC24M9-
RC20M13- / RC20M12- 4.8
RM16M23- /RM14M30- RC16M23- /RC14M30- 7.1
#12 - Ø 2.4mm
8291 1457- / 8291 1459-
8291 1461- / 8291 1463-
8291 1465- / 8291 1467-
8291 1456- / 8291 1458-
8291 1460- / 8291 1462-
8291 1464- / 8291 1466-
7 to 8
#8
- Ø 3.6mm
8291 3601- / 8291 3603-
8291 3605- / 8291 3607-
8291 3609-
8291 3600- / 8291 3602-
8291 3604- / 8291 3606-
8291 3608-
6.5 to 7.5
Stamped & formed #16 - Ø 1.6mm
SM24M1- / SM24ML1-
SM20M1- / SM20ML1-
SC24M1- / SC24ML1-
SC20M1- / SC20ML1- 4
SM16M11- / SM16ML11- SC16M11- / SC16ML11- 4.65
#20 - Ø 1mm
SM24W3- / SM24WL3-
SM20W3- / SM20WL3-
SC24W3- / SC24WL3-
SC20W3- / SC20WL3- 4
#16 - Ø 1.6mm
SM16M1- / SM16ML1- SC16M1- / SC16ML1- 6.35
SM14M1- / SM14ML1- SC14M1- / SC14ML1- 6.35
L
L
Without insulation support
L
With insulation support
Note: See page 129 for plating options and other contact details
UTO Series | Technical Information
141
Active
contact
part
Contact type
Die
location
on heads
Wire
section
range
Section
(mm²)
Tensile
straight
test (mini)
Height
(mm)
H (±0.075)
Width
(mm)
W (±0.075)
Tooling head
p/n
Machined
contacts size
#20
Ø 1 mm
RM24W3K
RC24W3K 26/24 AWG 26 0.12 min 15 N 0.95 1.27
S20RCM
AWG 24 0.25 max 32 N
RM20W3K
RC20W3K 22/20 AWG 22 0.32 min 40 N 1.26 1.78
AWG 20 0.50 max 60 N
RM18W3K
RC18W3K 20/18 AWG 20 0.50 max 60 N 1.35 1.86
AWG 18 0.82 max 90 N
S & F
contacts size
#20
Ø 1 mm
SM24WL3TK6*
SC24WL3TK6* 26/24 AWG 26 0.12 min 15 N 0.80 1.49
S20SCM20
AWG 24 0.25 max 32 N
SM20WL3TK6*
SC20WL3TK6* 22/20 AWG 22 0.32 min 40 N 1.01 1.53
AWG 20 0.50 max 60 N
Machined
contacts size
#16
Ø 1.6 mm
RM28M1K*
RC28M1K* 30/28 AWG 30 0.05 min 11 N 1.14 1.41
S16RCM20
AWG 28 0.08 max 11 N
RM24M9K*
RC24M9K* 26/24 AWG 26 0.12 min 15 N 1.15 1.41
AWG 24 0.25 max 32 N
RM20M13K*
RC20M13K* 22/20
AWG 22 0.32 min 40 N
1.26 1.76
AWG 20 0.50 max 60 N
RM20M12K*
RC20M12K*
AWG 22 0.32 min 40 N
AWG 20 0.50 max 60 N
RM16M23K*
RC16M23K*
20 AWG 20 0.50 max 60 N 1.66 2.18
S16RCM16
18 AWG 18 0.82 max 90 N 1.80 2.28
16 AWG 16 1.50 max 150 N 1.96 2.43
RM14M30K*
RC14M30K*
16 AWG 16 1.50 min 150 N 2.10 2.68 S16RCM14
14 AWG 14 2.50 min 230 N 2.30 2.78
S & F
contacts size
#16
Ø 1.6 mm
SM24ML1TK6*
SC24ML1TK6* 26/24 AWG 26 0.12 min 15 N 0.84 1.50
S16SCM20
AWG 24 0.25 max 32 N
SM20ML1TK6*
SC20ML1TK6* 22/20 AWG 22 0.32 min 40 N 1.02 1.54
AWG 20 0.50 max 60 N
SM16ML11TK6*
SC16ML11TK6*
18 AWG 18 0.82 min 90 N 1.32 2.09 S16SCML11
16 AWG 16 1.50 max 150 N 1.36 2.10
SM16ML1TK6*
SC16ML1TK6*
18 AWG 18 0.82 min 90 N 1.49 2.02
S16SCML1
16 AWG 16 1.50 max 150 N 1.7 2.05
SM14ML1TK6*
SC14ML1TK6* 14 AWG 14 2.50 max 230 N 1.79 2.58
*: example of plating options, for other plating see page 129
WW
H
H
Machined
contact
Stamped & Formed
contact
Crimping
One of the key factors which affects the performance of a connector is
the way contacts are terminated. Crimped connections are nowadays
seen as the best solution to ensure quality throughout the lifetime of
the product. Here are some reasons why we recommend this method
of termination for UTO connectors:
Advantages (Extract from the IEC 60352-2):
- Ef cient processing of connections at each production level
- Processing by fully-automatic or semi- automatic crimping
machines, or with hand operated tools
- No cold-soldered joints
- No degradation of the spring characteristic of female contacts
by the soldering temperature
- No health risk from heavy metal and ux steam
- Preservation of conductor exibility behind the crimped
connection
- No burnt, discolored and overheated wire insulation
- Good connections with reproducible electrical and mechanical
performances
- Easy production control.
To ensure that the crimp tooling is performing according to original
speci cations, it is important to carry out regular checks. A common
way to check the performance of tooling is with a simple pull test,
ideally using a dedicated electric pull tester. Minimum recommended
pull forces are indicated in the tables below:
Technical Information
UTO Series | Technical Information
142
Handle & Interchangeable Heads
User Guide
8) To control crimp quality, slighty pull cable with two ngers
to control retention.
3) Close the two pins simultaneously to maintain the head. 7) To crimp contact assembly-cable, tighten sharply the clip
to the end of the mechanism.
2) Choose the adapter head (sold separately), keep vertical and
slide it into the handle until the mechanical end.
6) Position the contact in the bottom of the tool by checking
its orientation.
1) Fully close then release the tool, keep it open.
Open the 2 pins.
5) Place conductors, with no deteriorations, in the bucket
contact. All strands to be located in the crimp bucket.
4) Strip the cable properly checking the size recommended
in the catalog on page 140.
UTO Series | Technical Information
143
Extraction Tools
Contact Extraction Instructions
Place the tool into the cavity from front face of the connector, push on the handle, then remove the contact.
RX2025GE1
Contact size Extractor
#20 RX20D44
#16 RX2025GE1
#12 51060210924
#8 51060210936
RX20D44
51060210924
51060210936
Note: all dimensions are in mm
L
L1
Shell
size
UTO0 UTO7
L max L1 max L2 max L3 max L max L1 max L2 max L3 max
842.8 36.8 80.7 57.2 46.8 36.8 85.8 57.2
10 55.8 50.3 98.6 92 60.5 50.3 102.7 92
12 57.1 51.4 99.3 93.7 61.4 51.4 106.4 93.7
14 62.5 56.3 100.3 94.6 67.6 56.3 104.8 94.6
L2
L3
Dimensions Overmoulded Harnesses
Technical Information
UTO Series | Technical Information
144
Shell size
10 12 14 16 18 20 22 24
Screws tightening
torque (Nm) 0.30/0.40 0.30/0.40 0.30/0.40 0.30/0.40 0.35/0.45 0.50/0.60 0.55/0.65 0.55/0.65
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert contacts into connector cavities (insert manually or use tool RTM2
0
5 crimp contacts)
• Place receptacle in the panel cut-out
• Secure receptacle with screws (not supplied)
Tighten screws: M2.5 for size connectors 10 to 22, M3 for size connectors 24
(recommended torque: see table below)
• For complete sealing of the system use optional gasket and sealed screw solution (not sold by SOURIAU).
Gasket (optional)
Rear mounting : Crimp version
Panel thickness:
2.5mm max
Receptacle ange
3mm max
2.
UTO
0
Assembly (Mounting Suggestion)
Assembly Instructions
Front mounting : Crimp version
Gasket (optional)
Panel
Receptacle
ange
Pa
3mm max
UTO Series | Technical Information
145
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert contacts into connector cavities (insert manually or use tool
RTM2
0
5 crimp contacts )
• Seat o-ring, place receptacle in the panel cut-out
• Tighten jam nut
O-ring
Jam nut
Panel thickness
UTO7 Assembly (Mounting Suggestion)
Shell size
Jam nut
torque
(Nm)
Exterior
jam nut
dim. (mm)
Ø Wire
max (mm)
Panel
thickness
max (mm)
10 6 22.2 3.2 3.2
12 9 27.0 3.2 3.2
14 10 32.0 3.2 3.2
16 13 33.3 3.2 3.2
18 20 36.5 3.2 3.2
20 23 39.7 3.2 6.4
22 25 42.9 3.2 6.4
24 26 46.0 3.2 6.4
Technical Information
UTO Series | Technical Information
146
•
• Slide accessories onto the cable
• Strip external cable jacket (see dimension H in the table below)
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert contacts into connector cavities (insert manually or use tool
RTM2
0
5)
• Screw adapter to the rear of the connector body and screw cable
gland body to adapter and tighten (recommended torque:
see table below)
•
Mate the plug with the receptacle to make the following step easier
• Slide ferrule inside the cable gland body as shown in g. A
• Tighten backshell nut with cable gland body as shown in g. B
(recommended torque: see below).
UTO0 or UTO7 with UTO6 + JCS or JC or JCSL or JCL for Unshielded Cable
Ferrule
Backshell nut
Adapter
UTO6
Cable gland body
H
UTO0
UTO7
g. A g. B
Shell size
Adapter
tightening torque
(Nm)
Cable gland body
tightening torque
(Nm)
Backshell nut
tightening torque*
(Nm)
H min. (mm)
JCS/JCSL
JC/JCL
Male Female Male Female
10 6 6 5 21 29 32 39
12 10 10 8 21 29 31 39
14 10 10 8 25 33 39 47
16 14 14 12 32 40 43 51
18 14 14 12 37 45 47 55
20 24 24 20 39 47 49 57
22 24 24 20 41 50 53 61
24 24 24 20 47 55 57 65
Spanner size
Shell size
JCS/JC
JSCL/JCL
Cable gland body Backshell nut Cable gland body Backshell nut
10 17 mm 14 mm 17 mm 17 mm
12 & 14 22 mm 20 mm 22 mm 22 mm
16 & 18 26 mm 24 mm 30 mm 30 mm
20, 22 & 24 33 mm 30 mm 40 mm 40 mm
* Indicative torque, needs to be adjusted depending on the cable used
Assembly Instructions (Continued)
UTO Series | Technical Information
147
•
• Slide accessories onto the cable
• Strip external cable jacket (see dimension H and L in the table below)
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert contacts into connector cavities (insert manually or use tool
RTM2
0
5)
• Screw adapter to the rear of the connector body and screw cable
gland body to adapter and tighten (recommended torque:
see table below)
•
Mate the plug with the receptacle to make the following step easier
• Slide ferrule inside the cable gland body as shown in g. A
• Tighten backshell nut with cable gland body as shown in g. B
(recommended torque: see below).
UTO0 or UTO7 with UTO6 + JCS or JC or JCSL or JCL for Shielded Cable
Shielding ferrule
Backshell nut
Adapter
UTO6
Cable gland body
H
L
UTO0
UTO7
Spanner size
Shell size
JCS/JC
JSCL/JCL
Cable gland body Backshell nut Cable gland body Backshell nut
10 17 mm 14 mm 17 mm 17 mm
12 & 14 22 mm 20 mm 22 mm 22 mm
16 & 18 26 mm 24 mm 30 mm 30 mm
20, 22 & 24 33 mm 30 mm 40 mm 40 mm
g. A g. B
Shell size
Adapter
tightening torque
(Nm)
Cable gland body
tightening torque
(Nm)
Backshell nut
tightening torque
(Nm)
H min. (mm) L min.
(inch)
JCS/JCSL
JC/JCL
Male Female Male Female
10 6 6 5 50586168 8
12 10 10 8 54 61 65 73 12
14 10 10 8 59 66 73 80 12
16 14 14 12 68 75 79 86 12
18 14 14 12 72 80 83 91 12
20 24 24 20 80 89 90 98 14
22 24 24 20 83 91 94 102 14
24 24 24 20 88 96 98 106 14
* Indicative torque, needs to be adjusted depending on the cable used
Technical Information
UTO Series | Technical Information
148
• Slide accessories onto the cable
• Strip external cable jacket
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert contacts into connector cavities (insert manually or use tool
RTM2
0
5)
• Tighten backshell with plug and mate plug with a receptacle
(recommended torque values to be applied according to the
table below)
• Tighten backshell screws.
Cable clamp
Modular
gasket
UTO0 or UTO7 with UTO6 + AC Backshell Assembly
UTO0
UTO7
UTO6
Shell size Cable clamp tightening torque (Nm) Clamp (mm)
Min Max
10 4 1.5 5.0
12 5 3.0 8.2
14 5 4.0 10.0
16 9 6.0 13.0
18 9 8.5 16.0
20 11 10.0 16.0
22 13 9.0 19.3
24 15 11.0 20.6
Assembly Instructions (Continued)
UTO Series | Technical Information
149
• Remove inner part of the modular gasket to adjust the internal
diameter to t the cable (see table)
• Slide accessories onto the cable
• Strip external cable jacket
• Strip wires and crimp contacts (see pages 140 & 141)
• Tighten backshell with plug and mate plug with a receptacle
(recommended torque values to be applied according to the
table below)
• Tighten backshell screws.
Right angle
cable clamp
UTO0 or UTO7 with UTO6 + LPGN Backshell Assembly
UTO0
UTO7
UTO6
Shell size Right angle cable clamp tightening torque (Nm) Ø Cable range (mm)
ABCD
10 6 5 7.5 10 -
12 10 7.5 10 13 -
14 10 7.5 10 13 -
16 14 7.5 11 13.5 16
18 14 10 13.5 17 20
20 24 10 13.5 17 20
22 24 10 13.5 17 20
24 24 18 22 25.5 29
Ø Cable range
A
B
C
D
Technical Information
UTO Series | Technical Information
150
•
• Mate UTO6 (plug) with UTO0 or UTO7 already mounted on a
panel
• Slide accessories onto the cable
• Strip external cable jacket (see dimension H and L)
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert contacts into connector cavities (insert manually or use
RTM2
0
5 tool)
• Place cable braid shield over inner shielding ferrule (See g. A)
and slide the outer ferrule over the braid shield for UTOS-JCPGN
• Screw PG-tube adapter with plug (recommended torque:
see below table)
• Tighten PG-nut with PG-tube adapter (See g. B)
• Tighten PG-nut screws.
UTO0 or UTO7 with UTO6 + JCPGN Backshell Assembly
Outer shielding
ferrule
Inner shielding
ferrule
PG- nut
PG-tube
adapter
UTO6 Modular
gasket
Washers
g. A g. B
UTO0
UTO7
Ø individual braid shield conductor betweenn 0.3 and 0.5mm
Torques to be applied with the plug mated with the receptacle.
Shell size PG-tube
tightening torque (Nm)
Ø Cable range (mm) H min. (mm) L min. (mm)
UTO UTOS
Pin contacts Socket contacts
10 4 4 to 10 4 to 8.8 26.5 34.2 17.6
12 6 4 to 11.9 4 to 11.9 26.5 34.2 17.6
14 10 6.5 to 13.5 6.5 to 13.5 29.6 37.2 20.6
16 10 6.5 to 16 6.5 to 16 31.6 39.2 22.6
18 10 6.5 to 16 6.5 to 16 36.9 42.3 26.7
20 15 9 to 21 9 to 21 36.4 41.8 26.1
22 15 9 to 21 9 to 21 43.4 48.8 33.2
24 15 17 to 29.5 17 to 29.5 43.8 49.2 33.6
H
L
sher
Assembly Instructions (Continued)
UTOS-JCPGN
UTO Series | Technical Information
151
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert rst contact into the grommet ( rst contact in cavity A,
no tool is required). Then insert the contact in the connector
cavity A (insert manually or use tool RTM2
0
5)
• Insert the other contacts
• Tighten the nut to rear of either UTO7 or UTO6 (recommended
torque values to be applied according to the table below).
Nut
UTO6 or UTO7 with GN Backshell Assembly
UTO7
UTO6
Shell size layout Nut tightening torque (Nm) Ø Wire
10 41
From
1.7 mm
to
3.0 mm
12 8 1.5
14 7 1.5
14 12 1.5
Grommet +
compression ring
Technical Information
UTO Series | Technical Information
152
• Strip wires and crimp contacts (see pages 140 & 141)
• Insert rst contact into the grommet ( rst contact in cavity A,
no tool is required). Then insert the contact in the connector
cavity A (insert manually or use tool RTM2
0
5)
• Insert the other contacts
• Tighten adapter with plug, choose right seal (waste the other
seal)
• Tighten the nut to rear of either UTO7 or UTO6 (recommended
torque values to be applied according to the table below).
Nut
Cable range
UTO6 or UTO7 with GJC Backshell Assembly
Adapter + mounted gasket
UTO7
Grommet +
compression ring
UTO6
Cable ranges
Reducing Standard
Assembly Instructions (Continued)
Shell
size Layout
Recommended jacket
strip length (mm) Adapter tightening
torque (Nm)
Nut tightening
torque (Nm)
Ø Cable range
Standard seal
(mm)
Ø Cable range
Reducing seal
(mm)
Ø Wire
Male Female
10 4 21 29 1.5 1 2.5/8.0 1.5/5.0 From
1.7 mm
to
3.0 mm
12 8 25 33 2 2.5 5.0/12.0 3.0/9.0
14 7 29 36 3 2.5 7.0/14.0 5.0/12.0
14 12 29 36 3 2.5 7.0/14.0 5.0/12.0
UTO Series | Technical Information
153
B
A
UTO0 + UTO6 + AC
UTO7 + UTO6 + AC
F
E
UTO0 + UTO6 + UTO with
JCS or JC or JCSL or JCL
UTO7 + UTO6 + UTO with
JCS or JC or JCSL or JCL
L
H
UTO0 + UTO6 + UTOS with
JCS or JC or JCSL or JCL
UTO7 + UTO6 + UTOS with
JCS or JC or JCSL or JCL
D
C
UTO0 + UTO6GN
UTO7 + UTO6GN
Shell size
UTO0 + UTO6 UTO7+ UTO6
+ AC backshell + GN backshell + AC backshell + GN backshell
A max (mm) C max (mm) B max (mm) D max (mm)
10 53.5 39.1 58.3 43.9
12 53.5 38.9 58.3 43.7
14 52.0 39.4 56.8 44.2
16 55.5 - 60.3 -
18 56.5 - 61.3 -
20 58.5 - 64.0 -
22 57.0 - 62.5 -
24 59.0 - 64.5 -
Shell size
UTO0 + UTO6 + UTO with UTO7+ UTO6 + UTO with UTO0 + UTO6 + UTOS with UTO7+ UTO6 + UTOS with
JCS JC
JCSL
JCL JCS JC
JCSL
JCL JCS JC
JCSL
JCL JCS JC
JCSL
JCL
E max E max E max E max F max F max F max F max H max H max H max H max L max L max L max L max
10 68.1 80.1 68.1 80.1 72.8 84.8 72.8 84.8 78.1 90.1 79.1 91.1 82.8 94.8 83.8 95.8
12 68.1 81.1 69.1 82.1 72.8 85.8 73.8 86.8 81.1 94.1 81.1 94.1 85.8 98.8 85.8 98.8
14 73.1 87.1 74.1 88.1 77.8 91.8 78.8 92.8 86.1 100.1 86.1 100.1 90.8 104.8 90.8 104.5
16 82.1 93.1 88.1 99.1 86.8 97.8 92.8 103.8 92.1 103.1 102.1 113.1 96.8 107.8 106.8 117.8
18 85.1 95.6 91.1 101.6 89.8 100.3 95.8 106.3 95.1 105.6 105.1 115.6 99.8 110.3 109.8 120.3
20 98.4 108.2 105.4 115.2 103.9 113.7 110.9 120.7 111.9 121.7 120.9 130.7 117.4 127.2 126.4 136.2
22 100.7 112.0 107.7 119.0 106.2 117.5 113.2 124.5 114.2 125.5 123.2 134.5 119.7 131.0 128.7 140.0
24 106.9 116.9 113.9 123.9 112.4 122.4 119.4 129.4 120.4 130.4 129.4 139.4 125.9 135.9 134.9 144.9
Backshell without shielding Backshell with shielding
Mated Connector Length with Backshell
Note: all dimensions are in mm
Technical Information
UTO Series | Technical Information
154
N
M
UTO0 + UTO6 + JCPGN
UTO7 + UTO6 + JCPGN
Shell size UTO0 + UTO6 + JCPGN UTO7+ UTO6 + JCPGN
M max (mm) N max (mm)
10 82.4 87.1
12 84.6 89.3
14 89.6 94.3
16 95.0 99.7
18 99.1 103.8
20 111.1 116.6
22 118.2 123.7
24 132.9 138.5
Mated Connector Length with Backshell (Continued)
Note: all dimensions are in mm
UTO Series | Technical Information
155
Rated Current & Working Voltage
The current carrying capacity of a connector is limited by the thermal properties of materials used in its construction. The amount of current that
can be handled depends on the size of cable used, the ambient temperature and the heat that is generated inside the connector. Part 3 of the
IEC 60512 standard determines through a derating curve, the maximum current permissible, which varies from one layout to another (Fig.1 &
Fig.2). Wire size plays an important role in dissipating heat and avoid overheating (Fig.1 & Fig.3).
Please note that the curve should be adjusted when dealing with potential hot spots, which can occur as a result of unequal loading of current
across a number of contacts. As a general rule, it is best to avoid placing power handling contacts in the middle of the connector; try to locate
them towards the edge where heat can be dissipated more effectively. Eventually you should nd a level which represents the permissible ope-
rating range:
The rated current is de ned as uninterrupted continuous current that a connector can take when all contacts are energized simultaneously
without exceeding the maximum limit of temperature. The earth contact is never loaded.
0 20 40 60 80 100 120
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
Fig.1: UTO 12-4 – 1.5mm² wires
0 20 40 60 80 100 120
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
Fig.2: UTO 12-8 – 1.5mm² wires
Current use
Limited use
Not recommended use
0 20 40 60 80 100 120
0
3
5
8
10
13
15
18
20
23
25
28
30
Current (A)
Ambient Operating Temperature (°C)
Fig.3: UTO 12-4 – 2.5mm² wires
33
35
Current Carrying Capacity
Technical Information
UTO Series | Technical Information
156
EMC (Electro-Magnetic Compatibility) means a device (e.g.
a connector) can tolerate interferences and continue to work
properly.
It's generally measured via the shielding effectiveness.
This value is a ratio between the power radiated inside to the
maximum power interferences outside.
Shielding Effectiveness
(dB)=10Log Pin
Pout
Pin: Power in
Pout: Power out
Control of corrosion impact on electronic devices is an
important expertise. Metal connectors suitable for outdoor
and indoor use should be able to withstand climate ingress,
exposure to salt spray and corrosive gases while still
maintaining mechanical and electrical functionality.
Over the years, many different test methods have been
developed but never really captured the exact equivalence
between testing scenarios and real electronic device
exposure to corrosive environments. SOURIAU has been
developing, manufacturing and testing connector solutions
for more than 90 years and has developed a unique corrosion
test based on Salt Spray exposure combined with four
additional corrosive gases. Typical industrial applications
may involve exposure to corrosive atmospheres equivalent
to 48 or 96 hours. SOURIAU’s UTO product series has been
validated to withstand corrosive agent exposure at these
timeframes. In addition, we can offer different solutions
and plating options to withstand longer corrosion exposure
times and test up to 500 hours.
Corrosion Resistance
0 48 Hrs 96 Hrs 500 Hrs
Indoor application
Tempory outdoor exposure
Outdoor application
Outdoor application
with corrosive atmospheres
(Salt Spray and
4 Corrosive Gases)
Shielding Effectiveness/Corrosion
UTO Series | Technical Information
157
There are two main standards for industrial connectors: UL94 & UL1977
UL94
This standard is dedicated to plastics ammability. It characterises how the material burns in various orientation and thicknesses.
The UTO series has been rated at V-0 & HB.
Procedure: A specimen is supported in a vertical or horizontal position and a ame is applied to the bottom of the specimen. The ame is applied
for ten seconds and then removed until aming stops, at which time the ame is reapplied for another ten seconds and then removed. Two sets
of ve specimens are tested.
V-0 Vertical burning:
• Specimens must not burn with aming combustion for more
than 10 seconds after each test ame application
• Total aming combustion time must not exceed 50 seconds
for each set of 5 specimens
• Specimens must not burn with aming or glowing combustion
up to the specimen holding clamp
• Specimens must not drip aming particles that ignite
the cotton
• No specimen can have glowing combustion remain for longer
than 30 seconds after removal of the test ame.
Underwriter Laboratories
HB Horizontal burning:
• A material classi ed HB shall not have a burning rate
exceeding 40 mm per minute over a 75 mm span for
specimens having a thickness of 3.0 to 13 mm
• A material classi ed HB shall not have a burning rate
exceeding 75 mm per minute over a 75 mm span for
specimens having a thickness less than 3.0 mm
• A material classi ed HB shall cease to burn before the
100 mm reference mark.
45°
45°
Material
Material
100±1mm
25±1mm
10±1mm
Wire gauze
Wire gauze
UL94 + UL1977
~
~
125±1mm
300±1mm
45°
Cotton
Cotton
Material
Material
13±0.5mm
13±0.5mm
Technical Information
UTO Series | Technical Information
158
Underwriter Laboratories
UL1977
There are several standards which deal with plug and receptacle. Each of them is only for a small area of applications. It could be
telecommunication, etc. The UL 1977 covers single and multipole connectors intended for factory assembly.
Requirements apply to devices taking into account intensity and voltage. The categories are as follows:
Type 0 Type 1A
Tybe 1B
Type 2
Type 3
Type 4
0
0
31 A
1000 A
600 V
30 V
(42 V peak)
According to above table, the level of performance that has to be reached could be different. Most of them are explained in the following page.
Assembly:
Connector has to be keyed to prevent any mismating that can damage the machine or hurt the user. In the same way, plugs and sockets have to
be equipped to protect persons against contact with live parts.
Finally the identi ed grounding contact shall be located so that the corresponding electrical continuity has to be completed before any other
contact.
Insulating materials:
Material uses for electrical insulation, as a minimum, have to comply with the characteristics shown below:
• Minimum ratings for polymeric materials
Type Flame rating Relative thermal index (RTI)
Electrical/mechanical w/o impact */**
0- 50/50
1A HB 50/50
1B HB 50/50
2HB 50/50
3HB 50/50
4HB 50/50
* The RTI of the material shall not be lower than the temperature measured during
the Temperature Test.
** For a thickness less than that for which a value has been established, the RTI of
the minimum thickness with an established value shall be used.
UL94 + UL1977 (Continued)
UTO Series | Technical Information
159
Underwriter Laboratories
UL1977
Spacing:
For a 250V max connector, distance through air or over material shall be 1.2mm whereas from 250V to 600V connector the spacing is 3.2mm
minimum. These distances have to be taken between uninsulated live parts as shown in the matrix below:
An alternative way to determine voltage rating is with the Dielectric-Withstand test. If during one minute there is no arc-over or breakdown the
rated voltage is given as shown below:
a) 500 volts for a type 1B device
b) 1000 volts plus twice rated voltage for types 1A, 2, 3 and 4 devices.
• Applicability of spacing requirements
Type Uninsulated live part - uninsulated
live part of opposite polarity
Uninsulated live part - uninsulated
grounded metal part
Uninsulated live part - exposed dead
metal part
0No No No
1A Yes Yes Yes
1B Yes Yes No
2Yes Yes Yes
3Yes Yes Yes
4Yes Yes Yes
Marking:
A device shall be legibly marked with the manufacturer's trade name, trade mark, or other descriptive marking by which the organisation
responsible for the product may be identi ed. (Exception: If the device is too small, or where the legibility would be dif cult to attain, the
manufacturer’s name, trademark, or other descriptive marking may appear on the smallest unit container or carton)
The following shall be marked on the device or on the smallest unit container or carton or on a stuffer sheet in the smallest unit container or
carton:
a) The catalog number or an equivalent designation
b) The electrical rating in both volts and amperes, if assigned
c) Whether ac or dc, if restricted
d) Flammability class, if identi ed
Example - Marking for the arrangement 10-3: 10A 500V UL94 V-0
Technical Information
UTO Series | Technical Information
160
The norm is dedicated to connectors with rated voltage above 50V and up to 1000V and rated currents up to 125A per contact.
Depending on your application connectors should be compliant with another standard. This has to be double checked with the customer.
There are a lot of constructional requirements and performances speci ed in that standard. Most of them are illustrated in greater details hereafter.
Provisions for earthing:
The UTO connector is intended to be used on Class I or Class III (see IEC 61140) systems. Even if the purpose of our connector is not to interrupt
current, there is a need to add a protective earth contact. This one shall be a “First mate, last break” style. Critically, among all of the normal
assumptions we make in designing a connector, this contact has to be considered as a live part and must be protected attached to the ground
wire.
IP Code:
IP is a coding system de ned by the IEC 60529 to indicate the
degrees of protection provided by an enclosure. The aim of this is to
give information regarding the accessibility of live parts against ingress
of water and other foreign bodies.
1st digit Degree of protection 2nd digit Degree of protection
0No protection against accidental contact.
No protection against solid foreign bodies.
0No protection against water.
1Protection against contact with any large area by hand and against
large solid foreign bodies with a diameter bigger than 50 mm.
1Drip-proof.
Protection against vertical water drips.
2Protection against contact with the ngers.
Protection against solid foreign bodies with a diameter bigger than
12 mm.
2Drip-proof.
Protection against water drips up to a 15° angle.
3Protection against tools, wires or similar objects with a diameter
bigger than 2.5 mm.
Protection against small solid bodies with a diameter bigger than
2.5 mm.
3Spray-proof.
Protection against diagonal water drips up to a 60° angle.
4Same as 3 however diameter is bigger than 1 mm. 4Splash-proof.
Protection against splashed water from all directions.
5Full protection against contact. Protection against interior injurious
dust deposits.
5Hose-proof.
Protection against water (out of a nozzle) from all directions.
6Total protection against contact.
Protection against penetration of dust.
6Protection against temporary ooding.
7Protection against temporary immersions.
8Protection against water pressure.
Pressure to be speci ed by supplier.
9K High pressure hose-proof.
Protection against high pressure water (out of a nozzle) from all
directions.
IP 6 8
First digit
(foreign bodies
protection)
Second digit
(water
protection)
Code letters
(international
Protection)
UTO offers high sealing
performance IP68 / 69K…
Even in dynamic situations.
In addition to the IEC 60529 we conjointly use the DIN 40050 part 9
which are dedicated to road vehicles. The main differences are:
• First digit: 5 replaced by 5K, 6 by 6K. In the DIN the tested
equipment is not depressurized as it is in the IEC.
• Second digit: 5K and 6K has been added and are equivalent
respectively to 5 and 6 but with higher pressure.
9K which represents the High pressure cleaning.
IEC 61984 ed.2.0 “Copyright © 2008 IEC Geneva, Switzerland.www.iec.ch"
IEC 60664-1 ed.2.0 “Copyright © 2007 IEC Geneva, Switzerland.www.iec.ch”
IEC 61984
IEC 61984 & IP Codes Explained
UTO Series | Technical Information
161
Overvoltage
UTO connectors are quali ed to be used on systems rated at Overvoltage category III
Per the IEC 60664-1 (formely VDE 0110) each category is linked to the end application and where the device will be implemented:
• Category IV (primary overcurrent protection equipment):
Origin of the installation
• Category III (any xed installation with a permanent connection)
Fixed installation and equipment and for cases where the reliability and the availability is subject to special requirements
• Category II (domestic appliances):
Energy consuming equipment to be supplied from the xed installation
• Category I (protected electronic circuit):
For connection to circuit in which measures are taken to limit transient overvoltage.
Pollution degree
Per the IEC 60664-1 (formerly VDE 0110) the environment affects the performance of the insulation. Particles can build a bridge between
two metal parts. As a rule dust mixed with water can be conductive and more generally speaking metal dust is conductive. Finally, the
standard de nes 4 levels of pollution:
• Degree 1 (Air conditioned dry room):
No pollution or only dry, non conductive pollution occurs. The pollution has no in uence.
• Degree 2 (Personal computer in a residential area):
Only non conductive pollution occurs except that occasionally a temporary conductivity caused by condensation is to be
expected.
• Degree 3 (Machine tools):
Conductive pollution occurs or dry non-conductive pollution occurs which becomes conductive due to condensation which is to
be expected.
• Degree 4 (Equipments on roof, locomotives):
Continuous conductivity occurs due to conductive dust, rain or other wet conditions.
Finally, the harsher the environment is, the longer clearance and creepage distances should be. Nonetheless, according the IEC 61984,
enclosure rated at IP54 or higher can be dimensioned for a lower pollution degree. This applies to mated connectors disengaged for test and
maintenance.
Marking
The marking should give enough details to the user to know what the main characteristics are and without going deep in technical
documentation. Below examples identify the suitability of the connector:
• Example 1:
Marking of a connector with rated current 16A, rated voltage 400V, rated impulse voltage 6kV and pollution degree 3, 2 and 1 for
use in any system, preferably unearthed or delta-earthed systems:
16A 400V 6kV 3
• Example 2:
Marking of a connector with rated current 16A, rated insulation voltages line-to-earth 250V, line-to-line 400V, rated impulse
voltage 4kV and pollution degree 3, 2 and 1 for use in earthed systems:
16A 250V 400V 4kV 3
16A 250V 400V 4kV 3
16A 400V 6kV 3
IEC 61984
Technical Information
UTO Series | Technical Information
162
On a daily basis, we are using many electrical appliances, some are grounded, and some are not. The levels of grounding protection are clearly
de ned by the International Electrotechnical Commission standard IEC 61140, a standard that has an in uence on our connectors and how
they should be used; our customers therefore need to pay particular attention to the three categories de ned within this standard to ensure
compatibility with their system. Everything explained hereafter is valid for connectors not intended to interrupt current.
Class I:
Devices which belong to this category have their chassis grounded via the ground wire (green/yellow in Europe, green in the US, Canada and
Japan). A fault in the appliance might cause a live conductor to energize the casing. In this case, the current ows to the ground conductor and
the circuit interrupter will cut off the power supply. In case of the UTO series, it means the envelope (coupling ring, backshell and housing) may
become live, therefore, care needs to be taken to attach the connector to the ground. This is usually done via the ground conductor using a splice
between the ground contact and the housing.
Class II:
Products in this category have reinforced insulation, meaning that the casing does not need to be connected to ground. In this case, the possibility
of electric shock has been removed. Most of the time, reinforced insulation means double insulation, i.e. the second layer will take over the rst
one in case the rst one fails. The UTO series is not designed to comply with this standard, so we cannot recommend it for this product category.
Note: UL 1310 also de nes a class II device, but in that case this is just to set the upper limit of use, like a wall charger for our cell phone.
Class III:
In this category, electrical appliances are fed by a low voltage source (<48VAC or < 120VDC). In normal conditions live conductors can be
accessible without any risk for the end user. No particular attention needs to be taken in regards to UTO series when it comes to a class III device.
Conclusion :
UTO series can be used in class I and class III environments, but each category affects the product performance. Throughout the catalog, current
and voltage ratings have been given for class I devices keeping in mind the ground conductor needs to be attached according to recommended
wiring instructions.
Note: Special applications like recreational vehicles are not under the scope of the IEC 61140.
IEC 61140
IEC 61140 Explained
UTO Series | Technical Information
163
Enclosure
rating IP20 IP22 IP55 IP64 IP65 IP66 IP67
Type 1 •
Type 3 •
Type 3R •
Type 3S •
Type 4 •
Type 4X •
Type 6 •
Type 12 •
Type 13 •
• indicates compliance
6 IP67 Enclosures constructed for either indoor or outdoor use to provide a degree of protection to personnel against incidental
contact with the enclosed equipment, falling dirt, hose-directed water, the entry of water during occasional temporary
submersion at a limited depth and damage from external ice formation.
6P IP67 Enclosures constructed for either indoor or outdoor use to provide a degree of protection to personnel against incidental
contact with the enclosed equipment, falling dirt, hose-directed water, the entry of water during prolonged submersion at
a limited depth and damage from external ice formation.
Type 6 rating can be either Type 6 or Type 6P - please see below:
• NEMA ratings vs IP ratings
Whereas IP ratings only consider protection against ingress of foreign bodies (first digit) and ingress of water (second digit), NEMA ratings consider
these but also verify protection from external ice, corrosive materials, oil immersion, etc.
The correlation between NEMA & IP being limited only to dust and water, we can state that a NEMA type is equivalent to an IP rating but it is not
possible to say the contrary.
Below a list of some NEMA standards:
What is NEMA Rating ?
Technical Information
UTO Series | Technical Information
164
In order to explain basic Ethernet theory, we can use a functional comparison to a busy city with highways, buildings and cars. To illustrate this, the
table below provides correlation between the different components/pieces/links that encompass Ethernet network connectivity, and the larger scale
infrastructure of a metropolitan city.
Ethernet Basics
Ethernet is a widely used communications protocol that is used to transmit data packets (datagrams) between network devices. Imagine a highway in a
large metropolitan area six lanes wide at rush hour. The vehicles on the highway need rules to follow so that they get to their destination without crashing
into each other. In an Ethernet network link, there could be 100 million bits of information transmitted in one second. In the Ethernet standard, there exist
rules to govern packet structure, transmission requirements, error correction, communication with end equipment, etc.
Examining the differences between 100Mhz, 100 Base TX, Cat5e/Cat6.
What does it all mean?
When discussing connectors and Ethernet, there are a few key details to be aware of:
• 100Mhz is a measurement of Frequency for the signal
- Comparable to the Speed Limit of a highway
• 100BaseTX (or Fast Ethernet) is an Ethernet link standard and identi es available link bandwidth. The bandwidth is measured in units of
MBits/S (megabits per second)
- Comparable to the number of cars that pass a point in one second
• Cat5e/Cat6 are an EIA/TIA standard for performance and physical characteristics for cables and connectors
- Comparable to performance speci cations of the car and highway.
In connectors and cables, Fast Ethernet uses 2 pairs. One for transmit and one for receive. This way data traf c can ow in both directions simultaneously.
• City: The network itself
• Buildings: End equipment, PC, server, etc.
• Roads: Ethernet cabling
• Cars: Data packets, datagrams, bits, bytes, etc.
• Tolls: Firewalls
• Bridges: Connectors
• Traf c laws: Protocol/communication speci cations
Ethernet for the layman
UTO Series | Technical Information
165
Souriau offering:
Standard solutions.
What about using coax contacts ?
Ethernet twisted pairs carry a symmetrical (balanced) signal. Once terminated into a coax contact, the inner core will be protected by a shield - but not
the outer contact. Because of EMI issues, the signal will no longer be balanced. Conclusion - it does not work and is not recommended.
Conclusion
To carry 100Mb/s data signal, 100BaseTX or Fast Ethernet recommends the use of Cat5e connectors as well as Cat5e cable with the support of a 100MHz
signal. Nevertheless, a 100Mb/s signal can be transmitted in certain conditions (short distance, only one connector, lower frequency but a different code)
thru many other connection materials - not necessarily Cat5e rated.
What about using Quadrax contacts ?
The Quadrax contact is used in railway applications because of the use of quad cable. In this speci c market, the standard Ethernet twisted pairs wires
cannot be offered, they are too thin and often solid (not stranded).
In the rest of industry, UTP (Unshielded Twisted Pairs) cables are widely used. The Quadrax contact is not designed to terminate them. And thus, are not
advised for industrial applications.
UTO size 12, 10 contacts - Cat5e
Twisted pairs
1 (Pair 1) ‹ C
2 (Pair 1) ‹ B
3 (Pair 2) ‹ G
4 (Pair 2) ‹ H
UTO size 16, 19 contacts -Cat5e
Twisted pairs (1Gb/s)
1 (Pair 1) ‹ A
2 (Pair 1) ‹ B
3 (Pair 2) ‹ D
4 (Pair 2) ‹ E
5 (Pair 3) ‹ G
6 (Pair 3) ‹ H
7 (Pair 4) ‹ K
8 (Pair 4) ‹ L
UTO size 10, 4 contacts - Cat6
Quad cable
1 (Pair 1) ‹ A
2 (Pair 1) ‹ B
1210
10 Ø 1 (#20) 1619
19 Ø 1.6 (#16)
104
4 Ø 1.6 (#16)
UTO size 10, 6 contacts - Cat5e
Twisted pairs
1 (Pair 1) ‹ A
2 (Pair 1) ‹ B
3 (Pair 2) ‹ E
4 (Pair 2) ‹ D
106
6 Ø 1 (#20)
Shielding continuity done in cavity C&F.
Note: Shielding can be replaced by
DC power.
Cat6 if shielding continuity done by other
contact
Technical Information
UTO SERIES
© 2013 SOURIAU - SOURIAU is a registered trademark
167
#16 Coaxial Contacts/Cabling Notices .................................................................. 168
Glossary of Terms ................................................................................................... 175
Drilling Pattern ....................................................................................................... 176
Discrimination/Keying Methods ............................................................................. 178
Part Number Index ................................................................................................. 181
Appendices
UTO Series
UTO Series | Appendices
168
#16 Coaxial Contacts
Cable
type
Impe-
dance
Contact
type
Ø over
jacket
Ø over
dielectric
Inner
cond
size
Ø outer braid
Male contact kit
for coaxial cable
Female contact kit
for coaxial cable
inch mm inch mm
Ext.
Ø
mm
inch mm
RG161/U 75
Multi
piece
0.09" 2.29 0.057" 1.45 - - -
RMDXK10D28 RCDXK1D28
RG179A/U 75 0.105" 2.67 0.063" 1.6 0.3 0.084" 2.13 max
RG179B/U 75 0.105" 2.67 0.063" 1.6 0.3 0.084" 2.13 max
RG187/U 75 0.11" 2.79 max 0.06" 1.52 0.3
RG188/U 50 0.11" 2.79 max 0.06" 1.52 0.51 0.078" 1.98 max
RG174/U 50 0.11" 2.92 0.06" 1.52 0.48 0.088" 2.24 max
AMPHENOL 21-598 50 0.105" 2.67 0.06" 1.52 0.48 - -
RG196/U 50 0.08" 2.03 max 0.034" 0.086 0.3 - --
RG178A/U 50 0.075" 1.91 0.034" 0.86 0.3 0.054" 1.37 max
RG/188A/U 50
Mono
crimp
0.110" 2.79 0.06" 1.52 0.51 0.078" 1.98 max RMDX6036D28 RCDX6036D28
KX21TVT (europe)
RG178 B/U 50 0.075" 1.91 0.034" 0.86 0.3 0.054" 1.37 max RMDX6034D28 RCDX6034D28
RG178 / BU 50 0.075" 1.91 0.034" 0.86 0.3 0.054" 1.37 max RMDX6050D28 RCDX6016D28
RG174/U 50 0.115" 2.92 0.06" 1.52 0.48 0.088" 2.24 max RMDX6032D28 RCDX6032D28
RG188A/U 50 0.11" 2.79 0.06" 1.52 0.51 0.078" 1.98 max RMDX6036D28 RCDX6036D28
RG316/U 50 0.107" 2.72 0.06" 1.52 0.51 0.078" 2.05 max RMDX6036D28 RCDX6036D28
raychem 5024A3111 50 0.12" 3.05 0.083" 2.11 0.64 0.097" 2.46 RMDX6052D28 RCDX6052D28
raychem 5026e1614 50 0.083" 2.11 0.05" 1.27 0.48 0.067" 1.7 RMDX6036D28 RCDX6036D28
surprenant pn 8134 -Multi
piece 0.1" 2.54 0.058" 1.47 0.3 - - RMDXK10D28 RCDXK1D28
PRD PN 247AS-
C1123-001 -
Mono
crimp
0.103" 2.62 0.06" 1.52 0.51 0.078" 1.98 RMDX6018D28 RCDX6018D28
PRD PN 247AS-C1251 - 0.092" 2.34 0.05" 1.27 0.64 0.067" 1.7 RMDX6018D28 RCDX6018D28
JUDD C15013010902 - 0.087" 2.13 0.05" 1.27 0.48 0.066" 1.67 RMDX6036D28 RCDX6036D28
CDC PIN22939200 - 0.09" 2.29 0.048" 1.22 0.3 0.064" 1.63 RMDX6046D28 RCDX6016D28
CDC PIN22939200 - 0.09" 2.29 0.048" 1.22 0.3 0.064" 1.63 RMDX6050D28 RCDX6016D28
CDC PIN245670000 - 0.104" 2.64 0.067" 1.7 0.3 0.083" 2.11 RMDX6050D28 RCDX6016D28
ampex - 0.114" 2.9 0.075" 1.91 0.38 0.09" 1.29 RMDX6032D28 RCDX6032D28
TI PN 920580 - 0.7" 1.78 0.038" 0.96 0.48 0.054v 1.37 RMDX6024D28 RCDX6024D28
Honeywell PN 58000062 - 0.12" 3.05 0.077" 1.96 0.41
solid 0.096" 2.44 RMDX6026D28 RCDX6026D28
-- 0.104" 2.64 0.067" 1.7 0.3 - 2.11 RMDX6050D28 -
-- 0.09" 2.29 0.048" 1.22 0.3 - 1.63 RMDX6050D28 -
-- 0.114" 2.9 0.075" 1.91 0.38 - 1.29 RMDX6032D28 RCDX6032D28
-- 0.07" 1.78 0.038" 0.96 0.48 - 1.37 RMDX6024D28 RCDX6024D28
-- 0.12" 3.05 0.077" 1.96 0.41 - 2.44 RMDX6026D28 RCDX6026D28
Coaxial Cable - Contact Monocrimp and Multipiece
UTO Series | Appendices
169
Cable
type
Contact
type
Inner
AWG
cond
Ø over
jacket
(single wire)
Inner cond size Ø outer
braid Male
contact kit for
coaxial cable
Female
contact kit for
coaxial cable
inch mm Stranded
de nition
Ext. Ø
mm inch mm
2#24 stranded MIL-W-16878 type B
Multi
piece
24 0.049" 1.24
max 7/.008 - - RMDXK10D28 RCDXK1D28
2 #24 solid MIL-W-76 type LW 24 0.047" 1.12
max 1/.0201 - - RMDXK10D28 RCDXK1D28
2 #26 stranded MIL-W-76 type LW
or MIL-W-16878 type B&E 26 0.043" 1.09
max 7/.0063 0.16 - - RMDXK10D28 RCDXK1D28
2 #28 solid MIL-W-81822/3 28 0.028" 0.71
max --
RMDXK10D28 RCDXK1D28
Twisted pair 1/.201 solid MIL-W-76
type LW or MIL-W-16878 26 0.044" 1.12
max 1/.0201 0.511 - - RMDXK10D28 RCDXK1D28
Twisted pair solid MIL-W-81822/3 28 0.028" 0.71
max 1/.0126 0.32 - - RMDXK10D28 RCDXK1D28
#28 7/.0036 per Hitachi spec
ec-711 (13-2820)
Mono
crimp
- 0.046" 1.17 7/.0036 - - - RMDX6031D28 +
YORX090
RCDX6031D28 +
YORX090
20218201 - 0.028" 0.71 - - - - RMDX6031D28 +
YORX090
RCDX6031D28 +
YORX090
#30 solid - 0.025" 0.64 - - - - RMDX6015D28 +
YORX090
RCDX6015D28 +
YORX090
#26 7/.0063 26 0.028" 0.71 7/.063 0.16 - - RMDX6031D28 +
YORX090
RCDX6031D28 +
YORX090
#26 19/.004 26 0.049" 1.24 19/.004 - - - RMDX6019D28 +
YORX090
RCDX6019D28 +
YORX090
#24 7/.008 24 0.049" 1.24 7/.008 - - - RMDX6019D28 +
YORX090
RCDX6019D28 +
YORX090
#24 19/.005 24 0.057" 1.45 19/.005 - - - RMDX6019D28 +
YORX090
RCDX6019D28 +
YORX090
-26 - 1.25 - - - 19x0.1 RMDX6019D28 +
YORX090
RCDX6019D28 +
YORX090
-24 - 1.25 - - - 7x0.2 RMDX6019D28 +
YORX090
RCDX6019D28 +
YORX090
-24 - 1.45 - - - 19x0.13 RMDX6019D28 +
YORX090
RCDX6019D28 +
YORX090
-26 - 0.7 - - - 7x0.16 RMDX6031D28 +
YORX090
RCDX6031D28 +
YORX090
Twisted Cable - Contact Monocrimp and Multipiece
Appendices
UTO Series | Appendices
170
Twisted Pair Cable Multipiece Contact Cabling
#16 Coaxial Contacts (Continued)
Cable
reference
Contact
type Male contact Female
contact
Crimp
tool
Die
set
Stop
bushing
Cable strip
length
Inner conduc-
tor crimp Braid crimp
A B C g dim t dim g dim t dim
2#24 stranded mil
w 16878 type B
Multi
piece RMDXK10D28 RCDXK1D28 M10S1J - - See assembly notice
2 #24 solid mil-w-76
type LW
2 #26 stranded
mil w 76 type LW or
mil w16878 type B & E
2 #28 solid
mil-w-81822/3
twisted pair 1/.201 solid
mil w 76 type LW or mil
w 16878
twisted pair solid mil w
81822/3
Male contact
Outer male contact
RMDX60-2
Inner socket
RFD26L-1
Outer hyring
YOC074
Inner supporting
sleeve
RMDXB-055-3
Twisted pair
adapter
YORK-090 Conductor "Y"
Conductor "Z"
Strip lengths
of cable
7.95±0.41
15.54±0.41
7.95±0.41
Outer hyring
Inner supporting
sleeve
Twisted pair adapter Locking louver typical
Grounding louver typical
Step 1: Step 2: Step 3:
7.54
0.25±0.05
5.94±0.41
7.54±0.41
15.54±0.41
7.95±0.41
When using solid wire atten
conductor "X" and "Z" using
N24FL-1 die as shown
Female contact
Step 1: Step 2: Step 3:
Outer hyring Supporting
sleeve
Twisted pair adapter
Conductor "W"
Conductor "X"
Strip lengths
of cable
6.35±0.41
13.49±0.41
7.95±0.41
Outer female contact
RCDX60-2
Inner pin
RMD26L-1
Outer hyring
YOC074
Inner supporting
sleeve
RCDXB-055-1
Twisted pair
adapter
YORK-090
Note : all dimensions are in mm
UTO Series | Appendices
171
Twisted Pair Cable Monocrimp Contact Cabling
Cable reference Contact
type
Male
contact
Female
contact
Crimp
tool
Die
set
Stop
bushing
Cable strip
length
Inner conductor
crimp Braid crimp
A B C g dim t dim g dim t dim
#28 7/.0036 per Hitachi spec
ec-711 (13-2820)
Mono
crimp
RMDX6031D28
+ YORX090
RCDX6031D28
+ YORX090 M10S1J
S80 SL105 4.7 6.1 4.32 1.30 to
1.12 1.4 to 1.22 2.97 to
2.84 3.07 to 2.9
20218204 S80 SL105 3.94 6.1 3.16 1.30 to
1.17 1.4 to 1.22 2.97 to
2.84
3.07 to
2.79
#30 solid S83 SL105 4.7 6.1 4.06 1.22 to
1.12
1.35 to
1.22
2.97 to
2.84
3.12 to
2.95
#26 7/.0063 S80 SL105 4.7 6.1 4.06 1.30 to
1.17 1.4 to 1.22 2.97 to
2.84 3.07 to 2.9
#26 19/.004
M10SG8 ASSY'Y
TOOL DIE SET
STOP BUSHING
M10S1J TOOL
4.7 6.1 4.06 1.22 to
1.17
1.35 to
1.22
2.84 to
2.79
3.12 to
2.97
#24 7/.008 4.7 6.1 4.06 1.22 to
1.17
1.35 to
1.22
2.84 to
2.79
3.12 to
2.97
#24 19/.005 4.7 6.1 4.06 1.22 to
1.17
1.35 to
1.22
2.84 to
2.79
3.12 to
2.97
AWG26 (19x0.1)
M10SG8
crimping kit 4.7 6 4
AWG24 (7x0.2)
AWG24 (19x0.13)
AWG26 (7x0.16) S80 SL105
G
G
Braid crimp (G) to be measured with
die set fully closed
Inner conductor crimp (G) to be
measured with die set fully closed
RCDX60
Female coax contact
RMDX60
Male coax contact
See cable strip lengths
Cable strip length
A
BC
16 min.
• Select appropriate monocrimp coax twisted pair contact and cable combination.
• Select appropriate crimp tooling (hand tool, S-die set, stop bushing).
• Strip the twisted pair cable to the designated wire strip lengths.
• Insert the stripped cable into the contact. One cable is to be inserted into the
inside diameter of hyring, and pushed forward into the inner contact. The
second cable is to be inserted between the outside diameter of hyring and the
inside diameter of the outer contact body.
• Crimp the contact.
Note : all dimensions are in mm
Appendices
UTO Series | Appendices
172
Multipiece Male Contact with Coax Cable
Multipiece kit details
RMDXK10D28
includes
RMDX602D28 Outer contact
RFD26L1D28 Inner contact
YOC074 Outer hyring
RMDXB0553 Inner supporting
sleeve
Cable strip length
A
B
C
Dielectric
diameter
Contact assembly with dielectric diameter over 1.4mm - without inner supporting sleeve
Outer male contact
RMDX60-2
Inner socket
RFD26L-1
Outer hyring
YOC074
Strip lengths
of cable
15.88±0.41
4.37±0.41
7.95±0.41
Step 1:
- Assemble outer hyring onto cable
- Assemble inner socket to inner conductor and crimp
Step 2:
- Insert the assembly into the outer male contact
until the inner socket snaps into place
- The cable braid (shield) should now cover the
barrel of the outer male contact as shown
Step 3:
- Slide outer hyring forward against spring and
crimp in place as shown
Locking louver typical
Grounding louver typical
Contact assembly with dielectric diameter under 1.4mm - with inner supporting sleeve
Outer male contact
RMDX60-2
Inner socket
RFD26L-1
Outer hyring
YOC074
Strip lengths
of cable
17.53±0.41
7.54±0.41
9.12±0.41
Inner supporting
sleeve
RMDXB-055-3
Step 1:
- Assemble outer hyring onto cable
- Assemble supporting sleeve over dielectric and under braid
- Assemble inner socket to inner conductor, push back against
sleeve and crimp
Supporting
sleeve Outer hyring
Step 2:
- Insert the assembly into the outer male contact
until the inner socket snaps into place
- The cable braid (shield) should now cover the
barrel of the outer male contact as shown
Step 3:
- Slide outer hyring forward against spring and
crimp in place as shown
Locking louver typical
Grounding louver typical
#16 Coaxial Contacts (Continued)
Cable
reference Contact
Hyring
complementary
compoments
Outer contact crimp tool Inner contact crimp tool
Cable strip length
Crimp tool
M10S1J
Crimp tool
M10S1J
Die set Stop bushing Die set Stop bushing ABC
RG161U
Male:
RMDXK10D28
YOC074
S221 SL471
S23D2
SL46D2
4.37 7.95 15.88
RG179
4.37 7.95 15.88
RG187U
4.37 7.95 15.88
RG188/U
S26D2 4.37 7.95 15.88
RG174/U
4.37 7.95 15.88
RG178A/U
YOC074 +
RMDXB0553 S23D2 7.54 9.12 17.53
RG196U
7.54 9.12 17.53
AMPHENOL
21-598
YOC074
-4.37 7.95 15.88
surprenant pn
8134
-4.37 7.95 15.88
Note : all dimensions are in mm
UTO Series | Appendices
173
Multipiece Female Contact with Coax Cable
Contact assembly with dielectric diameter over 1.4mm - without inner supporting sleeve
Outer female contact
RCDX60-2
Inner pin
RMD26L-1
Outer hyring
YOC074
Strip lengths
of cable
11.13±0.41
4.37±0.41
Step 1:
- Assemble outer hyring onto cable
- Assemble inner pin to inner conductor and crimp
Step 2:
- Insert the assembly into the outer female contact
until the inner pin snaps into place
- The cable braid (shield) should now cover the
barrel of the outer female contact as shown
Step 3:
- Slide outer hyring forward against spring and
crimp in place as shown
Contact assembly with dielectric diameter under 1.4mm - with inner supporting sleeve
Outer female contact
RCDX60-2028
Inner pin
RMD26L-1
Outer hyring
YOC074
Strip lengths
of cable
11.13±0.41
6.35±0.41
Supporting sleeve
RCDXB-055-1
Supporting
sleeve
Outer hyring
Step 1:
- Assemble outer hyring onto cable
- Assemble supporting sleeve over dielectric and under braid
- Assemble inner pin to inner conductor, push back against
sleeve and crimp
Step 2:
- Insert the assembly into the outer female contact
until the inner pin snaps into place
- The cable braid (shield) should now cover the
barrel of the outer female contact as shown
Step 3:
- Slide outer hyring forward against spring and
crimp in place as shown
RCDXK1D28
includes
RCDX602D28 Outer contact
RMD26L1D28 Inner contact
YOC074 Outer hyring
RCDXB0553 Inner supporting
sleeve
Multipiece kit details Cable strip length
A
B
C
Dielectric
diameter
Cable
reference Contact
Hyring
complementary
compoments
Outer contact crimp tool Inner contact crimp tool
Cable strip length
Crimp tool
M10S1J
Crimp tool
M10S1J
Die set Stop bushing Die set Stop bushing ABC
RG161U
Female:
RCDXK1D28
YOC074
S221 SL471
S23D2
SL46D2
4.37
-
11.13
RG179
4.37 11.13
RG187U
4.37 11.13
RG188/U
S26D2 4.37 11.13
RG174/U
4.37 11.13
RG178A/U
YOC074 +
RMDXB0553 S23D2 6.35 11.13
RG196U
6.35 11.13
AMPHENOL
21-598
YOC074
-4.37 11.13
surprenant pn
8134
-4.37 11.13
Note : all dimensions are in mm
Appendices
UTO Series | Appendices
174
Coax Cable with Monocrimp Contact Cabling
RCDX60
Female coax contact
RMDX60
Male coax contact
See cable strip lengths
Cable strip length
A
B
C
• Select appropriate cable and contact combination.
• Select appropriate crimp tooling (hand tool, S-die set, stop bushing).
• Strip coax cable to the designated wire strip lengths.
• Insert the stripped coax into the rear of the contact.
• Crimp the contact.
#16 Coaxial Contacts (Continued)
Cable
reference
Male
contact
Female
contact
Crimp
tool
Die
set
Stop
bushing
Cable strip length Inner conductor
crimp Braid crimp
A B C g dim t dim g dim t dim
CDC PIN22939200 RMDX6046D28 RCDX6016D28
M10S1J
S80 SL105 4.19 5.97 8.51 1.30/1.17 1.40/1.22 2.77/2.64 3.02/2.84
CDC PIN22939200 RMDX6046D28 RCDX6016D28 S87 SL105 5.08 6.35 8.89 1.30/1.17 1.40/1.22 2.77/2.64 3.02/2.84
CDC PIN245670000 RMDX6050D28 RCDX6016D28 S80 SL105 5.08 6.35 8.89 1.30/1.17 1.40/1.22 2.97/2.84 3.12/2.95
KX21TVT (europe)
RG178 B/U RMDX6034D28 RCDX6034D28 S82 SL105 5.08 6.35 8.89 1.30/1.17 1.32/1.17 2.84/2.74 3.07/2.9
RG178 / BU RMDX6050D28 RCDX6016D28 S87 SL105 5.08 6.35 8.89 1.30/1.17 1.40/1.22 2.77/2.64 3.02/2.84
ampex RMDX6032D28 RCDX6032D28 S80 SL105 5.08 6.35 11.68 1.30/1.17 1.40/1.22 2.97/2.84 3.12/2.95
TI PN 920580 RMDX6024D28 RCDX6024D28 S82 SL105 5.08 6.35 8.89 1.35/1.19 1.42/1.27 2.87/2.74 3.07/2.9
RG174/U RMDX6032D28 RCDX6032D28 S80 SL105 5.08 6.35 11.68 1.30/1.17 1.40/1.22 2.97/2.84 3.12/2.95
Honeywell PN 58000062 RMDX6026D28 RCDX6026D28 S82 SL105 5.08 6.35 8.89 1.35/1.19 1.42/1.27 2.87/2.74 3.07/2.9
RG188A/U RMDX6036D28 RCDX6036D28 S80 SL105 5.08 6.35 11.68 1.30/1.17 1.40/1.22 2.97/2.84 3.12/2.95
RG316/U RMDX6036D28 RCDX6036D28 S80 SL105 5.08 6.35 11.68 1.30/1.17 1.40/1.22 2.97/2.84 3.12/2.95
PRD PN
247AS-C1123-001 RMDX6018D28 RCDX6018D28 M10SG8 ASSY'Y
TOOL DIE SET
STOP BUSHING
M10S1J TOOL
5.08 6.35 8.89 1.22/1.17 1.35/1.22 2.92/2.79 3.12/2.97
PRD PN 247AS-C1251 RMDX6018D28 RCDX6018D28 5.08 6.35 8.89 1.22/1.17 1.35/1.22 2.92/2.79 3.12/2.97
raychem 5024A3111 RMDX6052D28 RCDX6052D28 S88 SL105 5.08 6.35 11.68 1.37/1.27 1.45/1.32 2.92/2.79
raychem 5026e1614 RMDX6036D28 RCDX6036D28 M10SG8 ASSY'Y
TOOL DIE SET
STOP BUSHING
M10S1J TOOL
5.08 6.35 8.89 1.22/1.17 1.35/1.22 2.92/2.79 3.12/2.97
JUDD C15013010902 RMDX6036D28 RCDX6036D28 5.08 6.35 8.89 1.22/1.17 1.35/1.22 2.92/2.79 3.12/2.97
inner cond. #30,
braid diam 2.64 RMDX6050D28 - S80 SL105 5.1 6.35 8.9 - - - -
inner cond. #30,
braid diam 2.29 RMDX6050D28 - S87 SL105 4.2 6.35 8.5 - - - -
inner cond. #28,
braid diam 2.9 RMDX6032D28 RCDX6032D28 S80 SL105 5.1 6.35 11.7 - - - -
inner cond. #26,
braid diam 1.78 RMDX6024D28 RCDX6024D28 S82 SL105 5.1 6.35 8.9 - - - -
inner cond. #26,
braid diam 3.05 RMDX6026D28 RCDX6026D28 S82 SL105 5.1 6.35 8.9 - - - -
Note : all dimensions are in mm
UTO Series | Appendices
175
• Clearance
Per the IEC 60664-1 it is the shortest
distance between two conductive parts
even over the air.
• Creepage distance
Per the IEC 60664-1 it represents the
shortest distance along the surface
of the insulating material between two
conductive parts.
• Working voltage
Per the IEC 60664-1 it is the highest r.m.s. value of A.C. or D.C. voltage
across any particular insulation which can occur when the equipment is
supplied at rated voltage.
• Rated impulse voltage
Impulse withstands voltage value assigned by the manufacturer to
the equipment or to a part of it characterizing the speci ed withstand
capability of its insulation against transient overvoltage.
• Working current
It is the maximum continuous and not interrupted current able to be
carried by all contacts without exceeding the maximum temperature of
the insulating material.
• Transient voltage
Extract from the IEC 60664-1: Short duration overvoltage of a few
millisecond or less, oscillatory or non-oscillatory, usually highly damped.
• CTI (Comparative Tracking Index)
The CTI value is commonly used to characterise the electrical
breakdown properties of an insulating material. It allows users
to know the tendency to create creepage paths. This value
represents the maximum voltage after 50 drops of ammonium chloride
solution without any breakdown.
• RTI (Relative temperature Index):
Extract from ULs website:
Maximum service temperature for a material, where a class of
critical property will not be unacceptably compromised through
chemical thermal degradation, over the reasonable life of an
electrical product, relative to a reference material having a
con rmed, acceptable corresponding performance de ned RTI.
- RTI Elec: Electrical RTI, associated with critical electrical
insulating properties.
- RTI Mech Imp: Mechanical Impact RTI, associated with
critical impact resistance, resilience and exibility properties.
- RTI Mech Str: Mechanical Strength (Mechanical without
Impact) RTI, associated with critical mechanical strength where
impact resistance, resilience and exibility are not essential.
Air gap
Creepage distance
Glossary of Terms
Appendices
UTO Series | Appendices
176
Shell Size Dimensions (mm)
10
12
14
Drilling Pattern
4.9 3.3
1.6
33
33
33
33
33
3 2.5
3.1
2.5
0.7
0.8
2.6 2.6
1.5 3
2.8
3.3 1.6
103 104 103W3106 102W2
4.4 3.4
2
2.8
4.5 4
0.9
124 128 1210
3.1 3.1
3.1 3.1
142G1
3.6 3.6
2.1 4.2
1.6
6.6
3.3
4.9
2.8
5.7
14191412
2.2 0.7
3.8 5.8
5.1
2 1.4
1
2.2
4.5
5.9
1
0.3
2.9
5.5
1492
2.6 5.3
5.7
3.6 1.9
2.3
2.4
5.1
1.4
0.8
4.6
5.9
148
2
4.5 5
5.2
2.52.4
0.4
5.3
147
6.4 3.2
5.2
Hole sizes: #20=0.9mm, #16=1.3mm, #8=3.8mm
UTO Series | Appendices
177
Shell Size Dimensions (mm)
16
18
1823 1832
1.6 3.3
4.4
5.7
6.1
8.1
9
2.4
3.1
5.3
8.7
1.6
4.8
7.2
0.8
6.7
4
8.5
9.1
2.4
2.4
3.8
5.6
4.9
5.8
5.5
7.7
8.9
3.5
5
8.3
3.7
6.7
3.4
4.8
1.9
7.78.6
5.4
3
4.8 4.5
7.7
1.7
4.4
1.7
78
3.3
6
0.8
4
7.9
4.5
5.4
8.1
0.9
5.1
6.6 7.4
2.3
1.6
2.
1626
2.7
6.5
1
7.5
3.8
3.8
2.8
7.5
1
1619
Hole sizes: #20=0.9mm, #16=1.3mm, #8=3.8mm
Appendices
UTO Series | Appendices
178
Drilling Pattern (Continued)
Hole sizes: #20=0.9mm, #16=1.3mm, #8=3.8mm
Shell Size Dimensions (mm)
20
22
2235
0.3
2.2
5.7
9.6
1.6
4.9
8.2
11.5
1.9
3.9
6
8.1
10.1
0.1
2.2
4.2
6.2
8.4
1.4
5.5
2.5
6.5
11.6
2028
0.6
3.4
5.7
7
10
0.5
3.8
4.2
6
9.2
1.6
5.4
1.5
4.9
0.5
3.8
4.2
6
10
0.6
3.4
5.8
7
9.2
1.5
2.2
4.9
1.6
2.5
5.4
2.5
2041
1.7
4.7
7.1
10.1
1.6
3.7
6.7
8.5
2.9
3.3
5.9
3.2
6.2
10.6
0.8
2.5
3.8
5.3
0.8
2.3
3.2
6.2
3.4
6.9
8.5
10.6
4.0
6.3
7.2
10.1
2030
3.8
10.1
1.9
5.8
9.3
3.8
6.2
9.3
1.9
5.2
7.1
10.1
7.1
2238
3.7
1.9
3.9
3.3
5.5
6.7
7.8
9.7
11.2
7.1
8.5
10.6
11.5
1.9
2.8
6.3
7.8
9.1
0.9
3.9
4.6
6.7
7.9
11
11.6
10.2
11.4
UTO Series | Appendices
179
Hole sizes: #20=0.9mm, #16=1.3mm, #8=3.8mm
Shell Size Dimensions (mm)
22
24
2255
5.7
11.4
2.8
8.5
1.6
4.9
3.3
6.6
9.9
11.5
8.2
2461
3.3
2.6
4.9
7.9
9.1
10.1
10.4
12.3
5.7
6.3
8.6
9.9
11.5
3.4
1.7
3.7
4.3
6.0
7.2
13.3
6.5
6.7
9.3
11.5
12.9
13.6
0.7
0.2
1
3.3
3.5
5.4
5.9
6.7
7.9
10.2
4.1
7.2
9.6
9.9
11.9
13.1
13.6
2.5
1.1
2.3
4.4
5.8
8.7
11
12.7
3.1
5
5.6
7.1
8.5
9.2
11.5
2448
6.6
13.2
3.3
9.9
1.9
5.7
3.8
7.6
9.5
13.3
11.4
Appendices
UTO Series | Appendices
180
In applications where similar connectors are used next to each other,
mismatching can cause disturbances, system failure or even danger to
operating personnel.
To eliminate mismatching, all Trim Trio® connectors are offered with
discrimination keys to avoid interconnection system errors. In addition,
the connector insert can also be rotated inside the shell to create custom
keying options.
Connectors with rotated inserts can be ordered by adding the suf x W, X,
Y or Z to the standard part number.
e.g.
UT0W0106PH
(standard key)
UT0W0106PWH
(W key)
Consult us for Overmoulded harnesses.
Shell size Layout Discrimination key degrees
WX Y Z
10
103 ----
102W2 ----
104 45° - - -
103W3 ----
106 90° - - -
12
124 ----
128 26° - - -
1210 60° 155° 270° 295°
14
142G1 ----
147 ----
148 ----
1412 60° - - -
1492 49° 71° 145° -
1419 30° 165° 315° -
16 1619 30° 165° - 315°
1626 60° - 275° 338°
18 1823 - 158° - 270°
1832 85° 138° 222° 265°
20
2028 79° - 259° -
2030 34° 90° 123° 259°
2041 45° 126° 225° -
22
2235 13° 162° 198° 265°
2238 15° 47° 150° 331°
2255 30° 142° 226° 314°
24 2448 60° 120° 189° 351°
2461 90° 180° 270° 324°
Discrimination/Keying Methods
SMSPKE0 (only for UTO layouts using #16 contacts)
When one of these dummy contacts is used, the UTO connector
will only mate with a connector which has a vacant cavity at the
corresponding position.
The material used is polyamide 6.6. SMSPKE0
UTO Series | Appendices
181
Part Number Index
Connectors
UT00102W2PH................... P.32
UT00102W2PH6.................. P.32
UT00102W2SH................... P.32
UT00102W2SH6.................. P.32
UT00103PH..................... P.20
UT00103PH6.................... P.20
UT00103SH..................... P.20
UT00103SH6.................... P.20
UT00103W3PH................... P.40
UT00103W3PH6.................. P.40
UT00103W3SH................... P.40
UT00103W3SH6.................. P.40
UT00104PH..................... P.36
UT00104PH6.................... P.36
UT00104SH..................... P.36
UT00104SH6.................... P.36
UT00124PH..................... P.28
UT00124PH6.................... P.28
UT00124SH..................... P.28
UT00124SH6.................... P.28
UT00128PH..................... P.52
UT00128PH6.................... P.52
UT00128SH..................... P.52
UT00128SH6.................... P.52
UT001412PH.................... P.64
UT001412PH6................... P.64
UT001412SH.................... P.64
UT001412SH6................... P.64
UT00142G1PH................... P.24
UT00142G1PH6.................. P.24
UT00142G1SH................... P.24
UT00142G1SH6.................. P.24
UT00147PH..................... P.48
UT00147PH6.................... P.48
UT00147SH..................... P.48
UT00147SH6.................... P.48
UT00148PH..................... P.56
UT00148PH6.................... P.56
UT00148SH..................... P.56
UT00148SH6.................... P.56
UT001492PH.................... P.68
UT001492PH6................... P.68
UT001492SH.................... P.68
UT001492SH6................... P.68
UT001619PH.................... P.76
UT001619PH6................... P.76
UT001619SH.................... P.76
UT001619SH6................... P.76
UT001823PH.................... P.80
UT001823PH6................... P.80
UT001823SH.................... P.80
UT001823SH6................... P.80
UT002028PH.................... P.88
UT002028PH6................... P.88
UT002028SH.................... P.88
UT002028SH6................... P.88
UT002030PH.................... P.92
UT002030PH6................... P.92
UT002030SH.................... P.92
UT002030SH6................... P.92
UT002235PH.................... P.100
UT002235PH6................... P.100
UT002235SH.................... P.100
UT002235SH6................... P.100
UT002238PH.................... P.104
UT002238PH6................... P.104
UT002238SH.................... P.104
UT002238SH6................... P.104
UT002448PH.................... P.112
UT002448PH6................... P.112
UT002448SH.................... P.112
UT002448SH6................... P.112
UT06102W2PH................... P.32
UT06102W2PH02................. P.32
UT06102W2SH................... P.32
UT06102W2SH02................. P.32
UT06103PH..................... P.20
UT06103PH02................... P.20
UT06103SH..................... P.20
UT06103SH02................... P.20
UT06103W3PH................... P.40
UT06103W3PH02................. P.40
UT06103W3SH................... P.40
UT06103W3SH02................. P.40
UT06104PH..................... P.36
UT06104PH02................... P.36
UT06104SH..................... P.36
UT06104SH02................... P.36
UT06124PH..................... P.28
UT06124PH02................... P.28
UT06124SH..................... P.28
UT06124SH02................... P.28
UT06128PH..................... P.52
UT06128PH02................... P.52
UT06128SH..................... P.52
UT06128SH02................... P.52
UT061412PH.................... P.64
UT061412PH02.................. P.64
UT061412SH.................... P.64
UT061412SH02.................. P.64
UT06142G1PH................... P.24
UT06142G1PH02................. P.24
UT06142G1SH................... P.24
UT06142G1SH02................. P.24
UT06147PH..................... P.48
UT06147PH02................... P.48
UT06147SH..................... P.48
UT06147SH02................... P.48
UT06148PH..................... P.56
UT06148PH02................... P.56
UT06148SH..................... P.56
UT06148SH02................... P.56
UT061492PH.................... P.68
UT061492PH02.................. P.68
UT061492SH.................... P.68
UT061492SH02.................. P.68
UT061619PH.................... P.76
UT061619PH02.................. P.76
UT061619SH.................... P.76
UT061619SH02.................. P.76
UT061823PH.................... P.80
UT061823PH02.................. P.80
UT061823SH.................... P.80
UT061823SH02.................. P.80
UT062028PH.................... P.88
UT062028PH02.................. P.88
UT062028SH.................... P.88
UT062028SH02.................. P.88
UT062030PH.................... P.92
UT062030PH02.................. P.92
UT062030SH.................... P.92
UT062030SH02.................. P.92
UT062235PH.................... P.100
UT062235PH02.................. P.100
UT062235SH.................... P.100
UT062235SH02.................. P.100
UT062238PH.................... P.104
UT062238PH02.................. P.104
UT062238SH.................... P.104
UT062238SH02.................. P.104
UT062448PH.................... P.112
UT062448PH02.................. P.112
UT062448SH.................... P.112
UT062448SH02.................. P.112
UT07102W2PH................... P.32
UT07102W2PH01................. P.32
UT07102W2PH6.................. P.32
UT07102W2PH601................ P.32
UT07102W2SH................... P.32
UT07102W2SH01................. P.32
UT07102W2SH6.................. P.32
UT07102W2SH601................ P.32
UT07103PH..................... P.20
UT07103PH01................... P.20
UT07103PH6.................... P.20
UT07103PH601.................. P.20
UT07103SH..................... P.20
UT07103SH01................... P.20
UT07103SH6.................... P.20
UT07103SH601.................. P.20
UT07103W3PH................... P.40
UT07103W3PH01................. P.40
UT07103W3PH6.................. P.40
UT07103W3PH601................ P.40
UT07103W3SH................... P.40
UT07103W3SH01................. P.40
UT07103W3SH6.................. P.40
UT07103W3SH601................ P.40
UT07104PH..................... P.36
UT07104PH01................... P.36
UT07104PH6.................... P.36
UT07104PH601.................. P.36
UT07104SH..................... P.36
UT07104SH01................... P.36
UT07104SH6.................... P.36
UT07104SH601.................. P.36
UT07124PH..................... P.28
UT07124PH01................... P.28
UT07124PH6.................... P.28
UT07124PH601.................. P.28
UT07124SH..................... P.28
UT07124SH01................... P.28
UT07124SH6.................... P.28
UT07124SH601.................. P.28
UT07128PH..................... P.52
UT07128PH01................... P.52
UT07128PH6.................... P.52
UT07128PH601.................. P.52
UT07128SH..................... P.52
UT07128SH01................... P.52
UT07128SH6.................... P.52
Appendices
UTO Series | Appendices
182
UT07128SH601.................. P.52
UT071412PH.................... P.64
UT071412PH01.................. P.64
UT071412PH6................... P.64
UT071412PH601................. P.64
UT071412SH.................... P.64
UT071412SH01.................. P.64
UT071412SH6................... P.64
UT071412SH601................. P.64
UT07142G1PH................... P.24
UT07142G1PH01................. P.24
UT07142G1PH6.................. P.24
UT07142G1PH601................ P.24
UT07142G1SH................... P.24
UT07142G1SH01................. P.24
UT07142G1SH6.................. P.24
UT07142G1SH601................ P.24
UT07147PH..................... P.48
UT07147PH01................... P.48
UT07147PH6.................... P.48
UT07147PH601.................. P.48
UT07147SH..................... P.48
UT07147SH01................... P.48
UT07147SH6.................... P.48
UT07147SH601.................. P.48
UT07148PH..................... P.56
UT07148PH01................... P.56
UT07148PH6.................... P.56
UT07148PH601.................. P.56
UT07148SH..................... P.56
UT07148SH01................... P.56
UT07148SH6.................... P.56
UT07148SH601.................. P.56
UT071492PH.................... P.68
UT071492PH01.................. P.68
UT071492PH6................... P.68
UT071492PH601................. P.68
UT071492SH.................... P.68
UT071492SH01.................. P.68
UT071492SH6................... P.68
UT071492SH601................. P.68
UT071619PH.................... P.76
UT071619PH01.................. P.76
UT071619PH6................... P.76
UT071619PH601................. P.76
UT071619SH.................... P.76
UT071619SH01.................. P.76
UT071619SH6................... P.76
UT071619SH601................. P.76
UT071823PH.................... P.80
UT071823PH01.................. P.80
UT071823PH6................... P.80
UT071823PH601................. P.80
UT071823SH.................... P.80
UT071823SH01.................. P.80
UT071823SH6................... P.80
UT071823SH601................. P.80
UT072028PH.................... P.88
UT072028PH01.................. P.88
UT072028PH6................... P.88
UT072028PH601................. P.88
UT072028SH.................... P.88
UT072028SH01.................. P.88
UT072028SH6................... P.88
UT072028SH601................. P.88
UT072030PH.................... P.92
UT072030PH01.................. P.92
UT072030PH6................... P.92
UT072030PH601................. P.92
UT072030SH.................... P.92
UT072030SH01.................. P.92
UT072030SH6................... P.92
UT072030SH601................. P.92
UT072235PH.................... P.100
UT072235PH01.................. P.100
UT072235PH6................... P.100
UT072235PH601................. P.100
UT072235SH.................... P.100
UT072235SH01.................. P.100
UT072235SH6................... P.100
UT072235SH601................. P.100
UT072238PH.................... P.104
UT072238PH01.................. P.104
UT072238PH6................... P.104
UT072238PH601................. P.104
UT072238SH.................... P.104
UT072238SH01.................. P.104
UT072238SH6................... P.104
UT072238SH601................. P.104
UT072448PH.................... P.112
UT072448PH01.................. P.112
UT072448PH6................... P.112
UT072448PH601................. P.112
UT072448SH.................... P.112
UT072448SH01.................. P.112
UT072448SH6................... P.112
UT072448SH601................. P.112
UT0W0106PH.................... P.44
UT0W0106PH6................... P.44
UT0W0106SH.................... P.44
UT0W0106SH6................... P.44
UT0W01210PH................... P.60
UT0W01210PH6.................. P.60
UT0W01210SH................... P.60
UT0W01210SH6.................. P.60
UT0W01419PH................... P.72
UT0W01419PH6.................. P.72
UT0W01419SH................... P.72
UT0W01419SH6.................. P.72
UT0W01626PH................... P.84
UT0W01626PH6.................. P.84
UT0W01626SH................... P.84
UT0W01626SH6.................. P.84
UT0W01832PH................... P.96
UT0W01832PH6.................. P.96
UT0W01832SH................... P.96
UT0W01832SH6.................. P.96
UT0W02041PH................... P.108
UT0W02041PH6.................. P.108
UT0W02041SH................... P.108
UT0W02041SH6.................. P.108
UT0W02255PH................... P.116
UT0W02255PH6.................. P.116
UT0W02255SH................... P.116
UT0W02255SH6.................. P.116
UT0W02461PH................... P.120
UT0W02461PH6.................. P.120
UT0W02461SH................... P.120
UT0W02461SH6.................. P.120
UT0W6106PH.................... P.44
UT0W6106PH02.................. P.44
UT0W6106SH.................... P.44
UT0W6106SH02.................. P.44
UT0W61210PH................... P.60
UT0W61210PH02................. P.60
UT0W61210SH................... P.60
UT0W61210SH02................. P.60
UT0W61419PH................... P.72
UT0W61419PH02................. P.72
UT0W61419SH................... P.72
UT0W61419SH02................. P.72
UT0W61626PH................... P.84
UT0W61626PH02................. P.84
UT0W61626SH................... P.84
UT0W61626SH02................. P.84
UT0W61832PH................... P.96
UT0W61832PH02................. P.96
UT0W61832SH................... P.96
UT0W61832SH02................. P.96
UT0W62041PH................... P.108
UT0W62041PH02................. P.108
UT0W62041SH................... P.108
UT0W62041SH02................. P.108
UT0W62255PH................... P.116
UT0W62255PH02................. P.116
UT0W62255SH................... P.116
UT0W62255SH02................. P.116
UT0W62461PH................... P.120
UT0W62461PH02................. P.120
UT0W62461SH................... P.120
UT0W62461SH02................. P.120
UT0W7106PH.................... P.44
UT0W7106PH01.................. P.44
UT0W7106PH6................... P.44
UT0W7106PH601................. P.44
UT0W7106SH.................... P.44
UT0W7106SH01.................. P.44
UT0W7106SH6................... P.44
UT0W7106SH601................. P.44
UT0W71210PH................... P.60
UT0W71210PH01................. P.60
UT0W71210PH6.................. P.60
UT0W71210PH601................ P.60
UT0W71210SH................... P.60
UT0W71210SH01................. P.60
UT0W71210SH6.................. P.60
UT0W71210SH601................ P.60
UT0W71419PH................... P.72
UT0W71419PH01................. P.72
UT0W71419PH6.................. P.72
UT0W71419PH601................ P.72
UT0W71419SH................... P.72
UT0W71419SH01................. P.72
UT0W71419SH6.................. P.72
UT0W71419SH601................ P.72
UT0W71626PH................... P.84
UT0W71626PH01................. P.84
UT0W71626PH6.................. P.84
UT0W71626PH601................ P.84
UT0W71626SH................... P.84
UT0W71626SH01................. P.84
UT0W71626SH6.................. P.84
Part Number Index (Continued)
UTO Series | Appendices
183
UT0W71626SH601................ P.84
UT0W71832PH................... P.96
UT0W71832PH01................. P.96
UT0W71832PH6.................. P.96
UT0W71832PH601................ P.96
UT0W71832SH................... P.96
UT0W71832SH01................. P.96
UT0W71832SH6.................. P.96
UT0W71832SH601................ P.96
UT0W72041PH................... P.108
UT0W72041PH01................. P.108
UT0W72041PH6.................. P.108
UT0W72041PH601................ P.108
UT0W72041SH................... P.108
UT0W72041SH01................. P.108
UT0W72041SH6.................. P.108
UT0W72041SH601................ P.108
UT0W72255PH................... P.116
UT0W72255PH01................. P.116
UT0W72255PH6.................. P.116
UT0W72255PH601................ P.116
UT0W72255SH................... P.116
UT0W72255SH01................. P.116
UT0W72255SH6.................. P.116
UT0W72255SH601................ P.116
UT0W72461PH................... P.120
UT0W72461PH01................. P.120
UT0W72461PH6.................. P.120
UT0W72461PH601................ P.120
UT0W72461SH................... P.120
UT0W72461SH01................. P.120
UT0W72461SH6.................. P.120
UT0W72461SH601................ P.120
Backshells
UT010AC....................... P.20
UT010AD....................... P.20
UT010JC....................... P.20
UT010JCL...................... P.20
UT010JCPGN.................... P.20
UT010JCS...................... P.20
UT010JCSL..................... P.20
UT010LPGN..................... P.20
UT012AC....................... P.28
UT012AD....................... P.28
UT012JC....................... P.28
UT012JCL...................... P.28
UT012JCPGN.................... P.28
UT012JCS...................... P.28
UT012JCSL..................... P.28
UT012LPGN..................... P.28
UT014AC....................... P.24
UT014AD....................... P.24
UT014JC....................... P.24
UT014JCL...................... P.24
UT014LPGN..................... P.24
UT014JCPGN.................... P.24
UT014JCSL..................... P.24
UT014LPGN..................... P.24
UT016AC....................... P.76
UT016AD....................... P.76
UT016JC....................... P.76
UT016JCL...................... P.76
UT016JCPGN.................... P.76
UT016JCS...................... P.76
UT016JCSL..................... P.76
UT016LPGN..................... P.76
UT018AC....................... P.80
UT018AD....................... P.80
UT018JC....................... P.80
UT018JCL...................... P.80
UT018JCS...................... P.80
UT018JCPGN.................... P.80
UT018JCSL..................... P.80
UT018LPGN..................... P.80
UT020AC....................... P.88
UT020AD....................... P.88
UT020JC....................... P.88
UT020JCL...................... P.88
UT020JCS...................... P.88
UT020JCPGN.................... P.88
UT020JCSL..................... P.88
UT020LPGN..................... P.88
UT022AC....................... P.100
UT022AD....................... P.100
UT022JC....................... P.100
UT022JCL...................... P.100
UT022JCS...................... P.100
UT022JCPGN.................... P.100
UT022JCSL..................... P.100
UT022LPGN..................... P.100
UT024AC....................... P.112
UT024AD....................... P.112
UT024JC....................... P.112
UT024JCL...................... P.112
UT024JCS...................... P.112
UT024JCPGN.................... P.112
UT024JCSL..................... P.112
UT024LPGN..................... P.112
UT0S10JC...................... P.20
UT0S10JCL..................... P.20
UT0S10JCPGN................... P.20
UT0S10JCS..................... P.20
UT0S10JCSL.................... P.20
UT0S12JC...................... P.28
UT0S12JCL..................... P.28
UT0S12JCS..................... P.28
UT0S12JCPGN................... P.28
UT0S12JCSL.................... P.28
UT0S14JC...................... P.24
UT0S14JCL..................... P.24
UT0S14JCPGN................... P.24
UT0S14JCS..................... P.24
UT0S14JCSL.................... P.24
UT0S16JC...................... P.76
UT0S16JCL..................... P.76
UT0S16JCPGN................... P.76
UT0S16JCS..................... P.76
UT0S16JCSL.................... P.76
UT0S18JC...................... P.80
UT0S18JCL..................... P.80
UT0S18JCPGN................... P.80
UT0S18JCS..................... P.80
UT0S18JCSL.................... P.80
UT0S20JC...................... P.88
UT0S20JCL..................... P.88
UT0S20JCPGN................... P.88
UT0S20JCS..................... P.88
UT0S20JCSL.................... P.88
UT0S22JC...................... P.100
UT0S22JCL..................... P.100
UT0S22JCPGN................... P.100
UT0S22JCS..................... P.100
UT0S22JCSL.................... P.100
UT0S24JC...................... P.112
UT0S24JCL..................... P.112
UT0S24JCPGN................... P.112
UT0S24JCS..................... P.112
UT0S24JCSL.................... P.112
Accessories
SMSPKE0....................... P.180
UT010DCG...................... P.22
UT012DCG...................... P.30
UT014DCG...................... P.26
UT016DCG...................... P.78
UT018DCG...................... P.82
UT020DCG...................... P.90
UT022DCG...................... P.102
UT024DCG...................... P.114
UTFD12B....................... P.22
UTFD13B....................... P.30
UTFD14B....................... P.26
UTFD15B....................... P.78
UTFD16B....................... P.82
UTFD17B....................... P.90
UTFD18B....................... P.102
UTFD19B....................... P.114
UTG610DCG..................... P.22
UTG612DCG..................... P.30
UTG614DCG..................... P.26
UTG616DCG..................... P.78
UTG618DCG..................... P.82
UTG620DCG..................... P.90
UTG622DCG..................... P.102
UTG624DCG..................... P.114
Contacts
82911456A..................... P.129
82911456K..................... P.129
82911457NA.................... P.129
82911457NK.................... P.129
82911458A..................... P.129
82911458K..................... P.129
82911459NA.................... P.129
82911459NK.................... P.129
82911460A..................... P.129
82911460K..................... P.129
82911461NA.................... P.129
82911461NK.................... P.129
82911462A..................... P.129
82911462K..................... P.129
82911463NA.................... P.129
82911463NK.................... P.129
82911464A..................... P.129
82911464K..................... P.129
82911465NA.................... P.129
82911465NK.................... P.129
82911466A..................... P.129
82911466K..................... P.129
82911467NA.................... P.129
82911467NK.................... P.129
Appendices
UTO Series | Appendices
184
82913600A..................... P.129
82913601A..................... P.129
82913602A..................... P.129
82913603A..................... P.129
82913604A..................... P.129
82913605A..................... P.129
82913606A..................... P.129
82913607A..................... P.129
82913608A..................... P.129
82913609A..................... P.129
82911684NPC................... P.132
82911684NAPC.................. P.132
82911685NPC................... P.132
82911685NAPC.................. P.132
RC14M30J...................... P.129
RC14M30K...................... P.129
RC14M30GE7J................... P.130
RC14M30GE7K................... P.130
RC16M23J...................... P.129
RC16M23K...................... P.129
RC16M23GE7J................... P.130
RC16M23GE7K................... P.130
RC18W3K....................... P.129
RC20M12J...................... P.129
RC20M12K...................... P.129
RC20M12E8J.................... P.132
RC20M12E8K.................... P.132
RC20M12E83J................... P.132
RC20M12E83K................... P.132
RC20M12E84J................... P.132
RC20M12E84K................... P.132
RC20M12GE7J................... P.130
RC20M12GE7K................... P.130
RC20M13J...................... P.129
RC20M13K...................... P.129
RC20M13GE7J................... P.130
RC20M13GE7K................... P.130
RC20W3K....................... P.129
RC24M9J....................... P.129
RC24M9K....................... P.129
RC24M9GE7J.................... P.130
RC24M9GE7K.................... P.130
RC24W3K....................... P.129
RC28M1J....................... P.129
RC28M1K....................... P.129
RC28M1GE7J.................... P.130
RC28M1GE7K.................... P.130
RCDX60xxD28................... P.131
RCDXK1D28..................... P.131
RCPOF1000B.................... P.130
RCW5016K...................... P.132
RCW50A7K...................... P.132
RM14M30J...................... P.129
RM14M30K...................... P.129
RM14M30GE1J................... P.130
RM14M30GE1K................... P.130
RM16M23J...................... P.129
RM16M23K...................... P.129
RM16M23GE1J................... P.130
RM16M23GE1K................... P.130
RM18W3K....................... P.129
RM20M12J...................... P.129
RM20M12K...................... P.129
RM20M12E8J.................... P.132
RM20M12E8K.................... P.132
RM20M12E83J................... P.132
RM20M12E83K................... P.132
RM20M12GE1J................... P.130
RM20M12GE1K................... P.130
RM20M13J...................... P.129
RM20M13K...................... P.129
RM20M13GE1J................... P.130
RM20M13GE1K................... P.130
RM20W3K....................... P.129
RM24M9J....................... P.129
RM24M9K....................... P.129
RM24M9GE1J.................... P.130
RM24M9GE1K.................... P.130
RM24W3K....................... P.129
RM28M1J....................... P.129
RM28M1K....................... P.129
RM28M1GE1J.................... P.130
RM28M1GE1K.................... P.130
RMDX60xxD28................... P.131
RMDXK10D28.................... P.131
RMPOF1000..................... P.130
RMW5016K...................... P.132
RMW50A7K...................... P.132
SC14M1S18..................... P.129
SC14M1S31..................... P.129
SC14M1TK6..................... P.129
SC14ML1S18.................... P.129
SC14ML1S31.................... P.129
SC14ML1TK6.................... P.129
SC16M1S18..................... P.129
SC16M1S31..................... P.129
SC16M1TK6..................... P.129
SC16M11S18.................... P.129
SC16M11S31.................... P.129
SC16M11TK6.................... P.129
SC16ML1S18.................... P.129
SC16ML1S31.................... P.129
SC16ML1TK6.................... P.129
SC16ML11S18................... P.129
SC16ML11S31................... P.129
SC16ML11TK6................... P.129
SC20M1S18..................... P.129
SC20M1S31..................... P.129
SC20M1TK6..................... P.129
SC20ML1S18.................... P.129
SC20ML1S31.................... P.129
SC20ML1TK6.................... P.129
SC20W3S25..................... P.129
SC20W3TK6..................... P.129
SC20WL3S25.................... P.129
SC20WL3TK6.................... P.129
SC24M1S18..................... P.129
SC24M1S31..................... P.129
SC24M1TK6..................... P.129
SC24ML1S18.................... P.129
SC24ML1S31.................... P.129
SC24ML1TK6.................... P.129
SC24W3S25..................... P.129
SC24W3TK6..................... P.129
SC24WL3S25.................... P.129
SC24WL3TK6.................... P.129
SM14M1S18..................... P.129
SM14M1S31..................... P.129
SM14M1TK6..................... P.129
SM14ML1S18.................... P.129
SM14ML1S31.................... P.129
SM14ML1TK6.................... P.129
SM16M1S18..................... P.129
SM16M1S31..................... P.129
SM16M1TK6..................... P.129
SM16M11S18.................... P.129
SM16M11S31.................... P.129
SM16M11TK6.................... P.129
SM16ML1S18.................... P.129
SM16ML1S31.................... P.129
SM16ML1TK6.................... P.129
SM16ML11S18................... P.129
SM16ML11S31................... P.129
SM16ML11TK6................... P.129
SM20M1S18..................... P.129
SM20M1S31..................... P.129
SM20M1TK6..................... P.129
SM20ML1S18.................... P.129
SM20ML1S31.................... P.129
SM20ML1TK6.................... P.129
SM20W3S26..................... P.129
SM20W3TK6..................... P.129
SM20WL3S26.................... P.129
SM20WL3TK6.................... P.129
SM24M1S18..................... P.129
SM24M1S31..................... P.129
SM24M1TK6..................... P.129
SM24ML1S18.................... P.129
SM24ML1S31.................... P.129
SM24ML1TK6.................... P.129
SM24W3S26..................... P.129
SM24W3TK6..................... P.129
SM24WL3S26.................... P.129
SM24WL3TK6.................... P.129
Tooling
51060210924................... P.139
51060210936................... P.139
M10S1J........................ P.174
M10SG8........................ P.174
M317.......................... P.139
MH860......................... P.139
MH86164G...................... P.139
MH86186....................... P.139
RX2025GE1..................... P.139
RX20D44....................... P.139
S16RCM14...................... P.139
S16RCM16...................... P.139
S16RCM20...................... P.139
S16SCM20...................... P.139
S16SCML1...................... P.139
S16SCML11..................... P.139
S20RCM........................ P.139
S20SCM20...................... P.139
S221.......................... P.172
S23D2......................... P.172
S80........................... P.174
S82........................... P.174
S83........................... P.171
S87........................... P.174
S88........................... P.174
SHANDLES...................... P.139
Part Number Index (Continued)
UTO Series | Appendices
185
SL105......................... P.174
SL46D2........................ P.172
SL471......................... P.172
UH25.......................... P.139
VGE10077A..................... P.139
VGE10078A..................... P.139
Appendices
UTO Series | Appendices
186
Notes
Your local contact
Our contribution to environmental
protection:
This catalog is printed on PEFC
certi ed paper
Advancement of sustainable
wood cultivation. www.pefc.org
www.souriau-industrial.com
contactindustry@souriau.com
CAUTOEUSEN01 © Copyright SOURIAU Oct 2013 - SOURIAU is a registered trademark
All information in this document presents only general particulars and shall not form part of any contract. All rights reserved to SOURIAU for changes without prior noti cation or public announcement. Any duplication is prohibited, unless approved in writing. Photos: Fotolia.com
