LM3875 LM3875 Overture Audio Power Amplifier Series High-Performance 56W Audio Power Amplifier Literature Number: SNAS083C LM3875 OvertureTM Audio Power Amplifier Series High-Performance 56W Audio Power Amplifier General Description Features The LM3875 is a high-performance audio power amplifier capable of delivering 56W of continuous average power to an 8 load with 0.1% THD+N from 20Hz to 20kHz. n n n n The performance of the LM3875, utilizing its Self Peak Instantaneous Temperature (Ke) (SPiKeTM) protection circuitry, puts it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe protection means that these parts are completely safeguarded at the output against overvoltage, undervoltage, overloads, caused by shorts to the supplies, thermal runaway, and instantaneous temperature peaks. The LM3875 maintains an excellent signal-to-noise ratio of greater than 95dB(min) with a typical low noise floor of 2.0V. It exhibits extremely low THD+N values of 0.06% at the rated output into the rated load over the audio spectrum, and provides excellent linearity with an IMD (SMPTE) typical rating of 0.004%. n n n n 56W continuous average output power into 8 100W instantaneous peak output power capability Signal-to-Noise Ratio > 95dB (min) Output protection from a short to ground or to the supplies via internal current limiting circuitry Output over-voltage protection against transients from inductive loads Supply under-voltage protection, not allowing internal biasing to occur when |V+| + |V-| 12V, thus eliminating turn-on and turn-off transients 11 lead TO-220 package Wide supply voltage range: |V+| + |V-| = 20V to 84V Applications n n n n Component or compact stereos Self-powered speakers Surround-sound amplifiers High-end stereo TVs Typical Application 01144901 *Optional components dependent upon specific design requirements. Refer to the External Components Description section for a component function description. FIGURE 1. Typical Audio Amplifier Application Circuit OvertureTM and SPiKeTM are trademarks of National Semiconductor Corporation. (c) 2004 National Semiconductor Corporation DS011449 www.national.com LM3875 Overture Audio Power Amplifier Series High-Performance 56W Audio Power Amplifier August 2000 LM3875 Connection Diagram Plastic Package (Note 8) 01144902 Top View Order Number LM3875T or LM3875TF See NS Package Number TA11B for Staggered Lead Non-Isolated Package or TF11B for Staggered Lead Isolated Package Equivalent Schematic (Excluding active protection circuitry) 01144906 www.national.com 2 Storage Temperature (Notes 1, -40C to +150C Thermal Resistance 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage |V+| + |V-| (No Signal) Common Mode Input Voltage Temperature Range 84V + 1C/W 43C/W Operating Ratings (Notes 1, 2) 94V Supply Voltage |V+| + |V-| (Input Signal) JC JA TMIN TA TMAX - (V or V ) and |V | + |V-| 80V -20C TA +85C + Differential Input Voltage Output Current Supply Voltage |V+| + |V-| 60V Internally Limited Power Dissipation (Note 3) 125W ESD Susceptibility (Note 4) 2500V Junction Temperature (Note 5) 150C Soldering Information T package (10 seconds) 260C 20V to 84V Note: Operation is guaranteed up to 84V, however, distortion may be introduced from the SPiKe Protection Circuitry when operating above 70V if proper thermal considerations are not taken into account. Refer to the Thermal Considerations section for more information. (See SPiKe Protection Response) Electrical Characteristics (Notes 1, 2) The following specifications apply for V+ = +35V, V- = -35V with RL = 8 unless otherwise specified. Limits apply for TA = 25C. LM3875 Symbol Parameter Conditions |V+| + |V-| Power Supply Voltage **PO Output Power (Continuous Average) Peak PO Instantaneous Peak Output Power THD + N Total Harmonic Distortion Plus Noise 40W, 20 Hz f 20 kHz AV = 26 dB **SR Slew Rate (Note 9) VIN = 1.414 Vrms, f = 10 kHz Square-wave, RL = 2 k *I+ Total Quiescent Power Supply Current VCM = 0V, VO = 0V, Io = 0 mA *VOS Input Offset Voltage IB Input Bias Current IOS Io THD + N = 0.1% (Max) f = 1 kHz, f = 20 kHz Typical (Note 6) 56 Limit (Note 7) Units (Limits) 20 84 V (Min) V (Max) 40 W (Min) 100 W 0.06 % 11 5 V/s (Min) 30 70 mA (Max) VCM = 0V, Io = 0 mA 1 10 mV (Max) VCM = 0V, Io = 0 mA 0.2 1 A (Max) Input Offset Current VCM = 0V, Io = 0 mA 0.01 0.2 A (Max) Output Current Limit |V+| = |V-| = 10V, ton = 10 ms, VO = 0V 6 4 A(Min) *Vod Output Dropout Voltage |V+-Vo-|, V+ = 20V, Io = +100 mA |Vo-V-|, V- = -20V, Io = -100 mA 1.6 2.7 5 5 V (Max) V (Max) *PSRR Power Supply Rejection Ratio V+ = 40V to 20V, V- = -40V, Vcm = 0V, Io = 0 mA V+ = 40V, V = -40V to -20V, Vcm = 0V, Io = 0 mA 120 120 85 85 dB (Min) *CMRR Common Mode Rejection Ratio V+ = 60V to 20V, V- = -20V to -60V, Vcm = 20V to -20V, Io = 0 mA 120 80 dB (Min) *AVOL Open Loop Voltage Gain |V+| = |V-| = 40V, RL = 2 k, VO = 60V 120 90 dB (Min) GBWP Gain-Bandwidth Product |V+| = |V-| = 40V fO = 100 kHz, VIN = 50 mVrms 8 2 MHz (Min) **eIN Input Noise IHF - A Weighting Filter RIN = 600 (Input Referred) 2.0 8.0 V (Max) 3 www.national.com LM3875 Absolute Maximum Ratings LM3875 Electrical Characteristics (Notes 1, 2) (Continued) The following specifications apply for V+ = +35V, V- = -35V with RL = 8 unless otherwise specified. Limits apply for TA = 25C. LM3875 Symbol SNR IMD Parameter Signal-to-Noise Ratio Intermodulation Distortion Test Conditions Typical (Note 6) Limit (Note 7) Units (Limits) PO = 1W, A-Weighted, Measured at 1 kHz, RS =25 98 dB dB PO = 40W, A-Weighted, Measured at 1 kHz, RS =25 114 dB dB Ppk = 100W, A-Weighted, Measured at 1 kHz, RS =25 122 dB dB 0.004 0.006 % 60 Hz, 7 kHz, 4:1 (SMPTE) 60 Hz, 7 kHz, 1:1 (SMPTE) *DC Electrical Test; refer to Test Circuit #1. **AC Electrical Test; refer to Test Circuit #2. Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 2: All voltages are measured with respect to supply GND, unless otherwise specified. Note 3: For operating at case temperatures above 25C, the device must be derated based on a 150C maximum junction temperature and a thermal resistance of JC = 1.0C/W (junction to case). Refer to the Thermal Resistance figure in the Application Information section under Thermal Considerations. Note 4: Human body model, 100 pF discharged through a 1.5 k resistor. Note 5: The operating junction temperature maximum is 150C, however, the instantaneous Safe Operating Area temperature is 250C. Note 6: Typicals are measured at 25C and represent the parametric norm. Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: The LM3875T package TA11B is a non-isolated package, setting the tab of the device and the heat sink at V- potential when the LM3875 is directly mounted to the heat sink using only thermal compound. If a mica washer is used in addition to thermal compound, CS (case to sink) is increased, but the heat sink will be isolated from V-. Note 9: The feedback compensation network limits the bandwidth of the closed-loop response and so the slew rate will be reduced due to the high frequency roll-off. Without feedback compensation, the slew rate is typically 16V/s. Note 10: The output dropout voltage is the supply voltage minus the clipping voltage. Refer to the Clipping Voltage vs. Supply Voltage graph in the Typical Performance Characteristics section. Test Circuit #1 (DC Electrical Test Circuit) 01144903 www.national.com 4 LM3875 Test Circuit #2 (AC Electrical Test Circuit) 01144904 Single Supply Application Circuit 01144905 *Optional components dependent upon specific design requirements. Refer to the External Components Description section for a component function description. FIGURE 2. Typical Single Supply Audio Amplifier Application Circuit 5 www.national.com LM3875 External Components Description (Figure 1 and Figure 2) Components Functional Description 1. RIN Acts as a volume control by setting the voltage level allowed to the amplifier's input terminals. 2. RA Provides DC voltage biasing for the single supply operation and bias current for the positive input terminal. 3. CA Provides bias filtering. 4. C Provides AC coupling at the input and output of the amplifier for single supply operation. 5. RB Prevents currents from entering the amplifier's non-inverting input which may be passed through to the load upon power-down of the system due to the low input impedance of the circuitry when the under-voltage circuitry is off. This phenomenon occurs when the supply voltages are below 1.5V. 6. *CC Reduces the gain (bandwidth of the amplifier) at high frequencies to avoid quasi-saturation oscillations of the output transistor. The capacitor also suppresses external electromagnetic switching noise created from fluorescent lamps. 7. Ri Inverting input resistance to provide AC Gain in conjunction with Rf1. 8. *Ci Feedback capacitor. Ensures unity gain at DC. Also a low frequency pole (highpass roll-off) at: 9. Rf1 Feedback resistance to provide AC Gain in conjunction with Ri. 10. *Rf2 At higher frequencies feedback resistance works with Cf to provide lower AC Gain in conjunction with Rf1 and Ri. A high frequency pole (lowpass roll-off) exists at: fc = 1/(2 Ri Ci). fc = [Rf1 Rf2] (s + 1/Rf2 Cf]/[(Rf1 + Rf2) (s + 1/Cf (Rf1 +Rf2))]. 11. *Cf Compensation capacitor that works with Rf1 and Rf2 to reduce the AC Gain at higher frequencies. 12. *RSN Works with CSN to stabilize the output stage by creating a pole that eliminates high frequency oscillations. 13. *CSN Works with RSN to stabilize the output stage by creating a pole that eliminates high frequency oscillations. = 1/(2RSN CSN). 14. *L Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce the Q of the series resonant circuit due to capacitive load. Also provides a low impedance at low frequencies to short out R and pass audio signals to the load. 15. *R 16. CS fc Provides power supply filtering and bypassing. *Optional components dependent upon specific design requirements. Refer to the Application Information section for more information. These two components act as low impedances to certain frequencies which will couple signals from the input to the output. Please take careful note of basic amplifier component functionality when designing in these components. The optional external components shown in Figure 2 and described above are applicable in both single and split voltage supply configurations. OPTIONAL EXTERNAL COMPONENT INTERACTION Although the optional external components have specific desired functions that are designed to reduce the bandwidth and eliminate unwanted high frequency oscillations they may cause certain undesirable effects when they interact. Interaction may occur for components whose reactances are in close proximity to one another. One example would be the coupling capacitor, CC, and the compensation capacitor, Cf. www.national.com 6 LM3875 Typical Performance Characteristics SPiKe Protection Response Safe Area 01144918 01144917 Supply Current vs Supply Voltage Pulse Thermal Resistance 01144919 01144920 Supply Current vs Output Voltage Pulse Thermal Resistance 01144922 01144921 7 www.national.com LM3875 Typical Performance Characteristics (Continued) Pulse Power Limit Pulse Power Limit 01144923 01144924 Supply Current vs Case Temperature Clipping Voltage vs Supply Voltage 01144925 01144926 Input Bias Current vs Case Temperature Peak Output Current 01144927 www.national.com 01144928 8 LM3875 Typical Performance Characteristics (Continued) THD + N vs Output Power THD + N vs Frequency 01144929 01144930 THD + N vs Output Power THD Distribution 01144931 01144932 Output Power vs Load Resistance THD Distribution 01144934 01144933 9 www.national.com LM3875 Typical Performance Characteristics (Continued) Max Heatsink Thermal Resistance (C/W) at the Specified Ambient Temperature (C) and Maximum Power Dissipation vs Supply Voltage 01144915 Note: The maximum heat sink thermal resistance values, OSA, in the table above were calculated using a OCS = 0.2C/W due to thermal compound. Power Dissipation vs Output Power Power Dissipation vs Output Power 01144935 01144936 Output Power vs Supply Voltage IMD 60 Hz, 4:1 01144937 www.national.com 01144938 10 LM3875 Typical Performance Characteristics (Continued) IMD 60 Hz, 7 kHz, 4:1 IMD 60 Hz, 7 kHz, 4:1 01144940 01144939 IMD 60 Hz, 1:1 IMD 60 Hz, 7 kHz, 1:1 01144941 01144942 Power Supply Rejection Ratio IMD 60 Hz, 7 kHz, 1:1 01144944 01144943 11 www.national.com LM3875 Typical Performance Characteristics (Continued) Common-Mode Rejection Ratio Large Signal Response 01144945 01144946 Open Loop Frequency Response Pulse Response 01144947 01144948 Thermal Protection: The LM3875 has a sophisticated thermal protection scheme to prevent long-term thermal stress to the device. When the temperature on the die reaches 165C, the LM3875 shuts down. It starts operating again when the die temperature drops to about 155C, but if the temperature again begins to rise, shutdown will occur again at 165C. Therefore the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but a sustained fault will cause the device to cycle in a Schmitt Trigger fashion between the thermal shutdown temperature limits of 165C and 155C. This greatly reduces the stress imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions. Since the die temperature is directly dependent upon the heat sink, the heat sink should be chosen as discussed in the Thermal Considerations section, such that thermal shutdown will not be reached during normal operation. Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor device. Application Information GENERAL FEATURES Under-Voltage Protection: Upon system power-up the under-voltage Protection Circuitry allows the power supplies and their corresponding caps to come up close to their full values before turning on the LM3875 such that no DC output spikes occur. Upon turn-off, the output of the LM3875 is brought to ground before the power supplies such that no transients occur at power-down. Over-Voltage Protection: The LM3875 contains overvoltage protection circuitry that limits the output current to approximately 4Apeak while also providing voltage clamping, though not through internal clamping diodes. The clamping effect is quite the same, however, the output transistors are designed to work alternately by sinking large current spikes. SPiKe Protection: The LM3875 is protected from instantaneous peak-temperature stressing by the power transistor array. The Safe Operating Area graph in the Typical Performance Characteristics section shows the area of device operation where the SPiKe Protection Circuitry is not enabled. The waveform to the right of the SOA graph exemplifies how the dynamic protection will cause waveform distortion when enabled. www.national.com 12 mal compound on both faces. Two-mil mica washers are most common, giving about 0.4C/W interface resistance with the compound. (Continued) THERMAL CONSIDERATIONS Silicone-rubber washers are also available. A 0.5C/W thermal resistance is claimed without thermal compound. Experience has shown that these rubber washers deteriorate and must be replaced should the IC be dismounted. Heat Sinking The choice of a heat sink for a high-power audio amplifier is made entirely to keep the die temperature at a level such that the thermal protection circuitry does not operate under normal circumstances. The heat sink should be chosen to dissipate the maximum IC power for a given supply voltage and rated load. Determining Maximum Power Dissipation Power dissipation within the integrated circuit package is a very important parameter requiring a thorough understanding if optimum power output is to be obtained. An incorrect maximum power dissipation (PD) calculation may result in inadequate heatsinking, causing thermal shutdown circuitry to operate and limit the output power. With high-power pulses of longer duration than 100 ms, the case temperature will heat up drastically without the use of a heat sink. Therefore the case temperature, as measured at the center of the package bottom, is entirely dependent on heat sink design and the mounting of the IC to the heat sink. For the design of a heat sink for your audio amplifier application refer to the Determining the Correct Heat Sink section. Since a semiconductor manufacturer has no control over which heat sink is used in a particular amplifier design, we can only inform the system designer of the parameters and the method needed in the determination of a heat sink. With this in mind, the system designer must choose his supply voltages, a rated load, a desired output power level, and know the ambient temperature surrounding the device. These parameters are in addition to knowing the maximum junction temperature and the thermal resistance of the IC, both of which are provided by National Semiconductor. As a benefit to the system designer we have provided Maximum Power Dissipation vs Supply Voltages curves for various loads in the Typical Performance Characteristics section, giving an accurate figure for the maximum thermal resistance required for a particular amplifier design. This data was based on JC = 1C/W and CS = 0.2C/W. We also provide a section regarding heat sink determination for any audio amplifier design where CS may be a different value. It should be noted that the idea behind dissipating the maximum power within the IC is to provide the device with a low resistance to convection heat transfer such as a heat sink. Therefore, it is necessary for the system designer to be conservative in his heat sink calculations. As a rule, the lower the thermal resistance of the heat sink the higher the amount of power that may be dissipated. This is, of course, guided by the cost and size requirements of the system. Convection cooling heat sinks are available commercially, and their manufacturers should be consulted for ratings. Proper mounting of the IC is required to minimize the thermal drop between the package and the heat sink. The heat sink must also have enough metal under the package to conduct heat from the center of the package bottom to the fins without excessive temperature drop. A thermal grease such as Wakefield type 120 or Thermalloy Thermacote should be used when mounting the package to the heat sink. Without this compound, the thermal resistance will be no better than 0.5C/W, and probably much worse. With the compound, thermal resistance will be 0.2C/W or less, assuming under 0.005 inch combined flatness runout for the package and heat sink. Proper torquing of the mounting bolts is important and can be determined from heat sink manufacturer's specification sheets. Should it be necessary to isolate V- from the heat sink, an insulating washer is required. Hard washers like berylum oxide, anodized aluminum and mica require the use of ther- The following equations can be used to accurately calculate the maximum and average integrated circuit power dissipation for your amplifier design, given the supply voltage, rated load, and output power. These equations can be directly applied to the Power Dissipation vs Output Power curves in the Typical Performance Characteristics section. Equation (1) exemplifies the maximum power dissipation of the IC and Equations (2), (3) exemplify the average IC power dissipation expressed in different forms. (1) PDMAX = VCC2/22 RL where VCC is the total supply voltage (2) PDAVE = (VOpk/RL) [VCC/ - VOpk/2] where VCC is the total supply voltage and VOpk = VCC/ (3) PDAVE = VCC VOpk/ RL - VOpk2/2 RL where VCC is the total supply voltage. Determining the Correct Heat Sink Once the maximum IC power dissipation is known for a given supply voltage, rated load, and the desired rated output power the maximum thermal resistance (in C/W) of a heat sink can be calculated. This calculation is made using Equation (4) and is based on the fact that thermal heat flow parameters are analogous to electrical current flow properties. It is also known that typically the thermal resistance, JC (junction to case), of the LM3875 is 1C/W and that using Thermalloy Thermacote thermal compound provides a thermal resistance, CS (case to heat sink), of about 0.2C/W as explained in the Heat Sinking section. Referring to the figure below, it is seen that the thermal resistance from the die (junction) to the outside air (ambient) is a combination of three thermal resistances, two of which are known, JC and CS. Since convection heat flow (power dissipation) is analogous to current flow, thermal resistance is analogous to electrical resistance, and temperature drops are analogous to voltage drops, the power dissipation out of the LM3875 is equal to the following: PDMAX = (TJmax - TAmb)/JA where JA = JC + CS + SA 01144910 13 www.national.com LM3875 Application Information LM3875 Application Information (Continued) But since we know PDMAX, JC, and SC for the application and we are looking for SA, we have the following: SA = [(TJmax - TAmb) - PDMAX (JC + CS)]/PDMAX (4) Again it must be noted that the value of SA is dependent upon the system designer's amplifier application and its corresponding parameters as described previously. If the ambient temperature that the audio amplifier is to be working under is higher than the normal 25C, then the thermal resistance for the heat sink, given all other things are equal, will need to be smaller. RMS reading, average responding, 3. 4. peak reading, and quasi peak reading. Although theoretical noise analysis is derived using true RMS based calculations, most actual measurements are taken with ARM (Average Responding Meter) test equipment. Typical signal-to-noise figures are listed for an A-weighted filter which is commonly used in the measurement of noise. The shape of all weighting filters is similar, with the peak of the curve usually occurring in the 3 kHz-7 kHz region as shown below. Equations (1), (4) are the only equations needed in the determination of the maximum heat sink thermal resistance. This is, of course, given that the system designer knows the required supply voltages to drive his rated load at a particular power output level and the parameters provided by the semiconductor manufacturer. These parameters are the junction to case thermal resistance, JC, TJmax = 150C, and the recommended Thermalloy Thermacote thermal compound resistance, CS. SIGNAL-TO-NOISE RATIO In the measurement of the signal-to-noise ratio, misinterpretations of the numbers actually measured are common. One amplifier may sound much quieter than another, but due to improper testing techniques, they appear equal in measurements. This is often the case when comparing integrated circuit designs to discrete amplifier designs. Discrete transistor amps often "run out of gain" at high frequencies and therefore have small bandwidths to noise as indicated below. 01144912 SUPPLY BYPASSING The LM3875 has excellent power supply rejection and does not require a regulated supply. However, to eliminate possible oscillations all op amps and power op amps should have their supply leads bypassed with low-inductance capacitors having short leads and located close to the package terminals. Inadequate power supply bypassing will manifest itself by a low frequency oscillation known as "motorboating" or by high frequency instabilities. These instabilities can be eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10 F or larger) which is used to absorb low frequency variations and a small ceramic capacitor (0.1 F) to prevent any high frequency feedback through the power supply lines. If adequate bypassing is not provided the current in the supply leads which is a rectified component of the load current may be fed back into internal circuitry. This signal causes low distortion at high frequencies requiring that the supplies be bypassed at the package terminals with an electrolytic capacitor of 470 F or more. 01144911 Integrated circuits have additional open loop gain allowing additional feedback loop gain in order to lower harmonic distortion and improve frequency response. It is this additional bandwidth that can lead to erroneous signal-to-noise measurements if not considered during the measurement process. In the typical example above, the difference in bandwidth appears small on a log scale but the factor of 10 in bandwidth, (200 kHz to 2 MHz) can result in a 10 dB theoretical difference in the signal-to-noise ratio (white noise is proportional to the square root of the bandwidth in a system). In comparing audio amplifiers it is necessary to measure the magnitude of noise in the audible bandwidth by using a "weighting" filter (Note 11). A "weighting" filter alters the frequency response in order to compensate for the average human ear's sensitivity to the frequency spectra. The weighting filters at the same time provide the bandwidth limiting as discussed in the previous paragraph. LEAD INDUCTANCE Power op amps are sensitive to inductance in the output lead, particularly with heavy capacitive loading. Feedback to the input should be taken directly from the output terminal, minimizing common inductance with the load. Lead inductance can also cause voltage surges on the supplies. With long leads to the power supply, energy is stored in the lead inductance when the output is shorted. This energy can be dumped back into the supply bypass capacitors when the short is removed. The magnitude of this transient is reduced by increasing the size of the bypass capacitor near the IC. With at least a 20 F local bypass, these voltage surges are important only if the lead length exceeds a couple feet ( > 1 H lead inductance). Twisting together the supply and ground leads minimizes the effect. Note 11: CCIR/ARM: A Practical Noise Measurement Method; by Ray Dolby, David Robinson and Kenneth Gundry, AES Preprint No. 1353 (F-3). In addition to noise filtering, differing meter types give different noise readings. Meter responses include: www.national.com 1. 2. 14 LM3875 Application Information (Continued) LAYOUT, GROUND LOOPS AND STABILITY The LM3875 is designed to be stable when operated at a closed-loop gain of 10 or greater, but as with any other high-current amplifier, the LM3875 can be made to oscillate under certain conditions. These usually involve printed circuit board layout or output/input coupling. When designing a layout, it is important to return the load ground, the output compensation ground, and the low level (feedback and input) grounds to the circuit board common ground point through separate paths. Otherwise, large currents flowing along a ground conductor will generate voltages on the conductor which can effectively act as signals at the input, resulting in high frequency oscillation or excessive distortion. It is advisable to keep the output compensation components and the 0.1 F supply decoupling capacitors as close as possible to the LM3875 to reduce the effects of PCB trace resistance and inductance. For the same reason, the ground return paths should be as short as possible. In general, with fast, high-current circuitry, all sorts of problems can arise from improper grounding which again can be avoided by returning all grounds separately to a common point. Without isolating the ground signals and returning the grounds to a common point, ground loops may occur. "Ground Loop" is the term used to describe situations occurring in ground systems where a difference in potential exists between two ground points. Ideally a ground is a ground, but unfortunately, in order for this to be true, ground conductors with zero resistance are necessary. Since real world ground leads possess finite resistance, currents running through them will cause finite voltage drops to exist. If two ground return lines tie into the same path at different points there will be a voltage drop between them. The first figure below shows a common ground example where the positive input ground and the load ground are returned to the supply ground point via the same wire. The addition of the finite wire resistance, R2, results in a voltage difference between the two points as shown below. 01144913 The load current IL will be much larger than input bias current I1, thus V1 will follow the output voltage directly, i.e., in phase. Therefore the voltage appearing at the non-inverting input is effectively positive feedback and the circuit may oscillate. If there were only one device to worry about then the values of R1 and R2 would probably be small enough to be ignored; however, several devices normally comprise a total system. Any ground return of a separate device, whose output is in phase, can feedback in a similar manner and cause instabilities. Out of phase ground loops also are troublesome, causing unexpected gain and phase errors. The solution to most ground loop problems is to always use a single-point ground system, although this is sometimes impractical. The third figure above is an example of a singlepoint ground system. The single-point ground concept should be applied rigorously to all components and all circuits when possible. Violations of single-point grounding are most common among printed circuit board designs, since the circuit is surrounded by large ground areas which invite the temptation to run a device to the closest ground spot. As a final rule, make all ground returns low resistance and low inductance by using large wire and wide traces. Occasionally, current in the output leads (which function as antennas) can be coupled through the air to the amplifier input, resulting in high-frequency oscillation. This normally happens when the source impedance is high or the input leads are long. The problem can be eliminated by placing a small capacitor, CC, (on the order of 50 pF-500 pF) across the LM3875 input terminals. Refer to the External Components Description section relating to component interaction with Cf. REACTIVE LOADING It is hard for most power amplifiers to drive highly capacitive loads very effectively and normally results in oscillations or ringing on the square wave response. If the output of the LM3875 is connected directly to a capacitor with no series 15 www.national.com LM3875 Application Information spond as quickly to nonlinearities. This decreased ability to respond to nonlinearities increases the THD + N specification. The desired input impedance is set by RIN. Very high values can cause board layout problems and DC offsets at the output. The value for the feedback resistance, Rf1, should be chosen to be a relatively large value (10 k-100 k), and the other feedback resistance, Ri, is calculated using standard op amp configuration gain equations. Most audio amplifiers are designed from the non-inverting amplifier configuration. (Continued) resistance, the square wave response will exhibit ringing if the capacitance is greater than about 0.2 F. If highly capacitive loads are expected due to long speaker cables, a method commonly employed to protect amplifiers from low impedances at high frequencies is to couple to the load through a 10 resistor in parallel with a 0.7 H inductor. The inductor-resistor combination as shown in the Typical Application Circuit isolates the feedback amplifier from the load by providing high output impedance at high frequencies thus allowing the 10 resistor to decouple the capacitive load and reduce the Q of the series resonant circuit. The LR combination also provides low output impedance at low frequencies thus shorting out the 10 resistor and allowing the amplifier to drive the series RC load (large capacitive load due to long speaker cables) directly. DESIGN A 40W/8 AUDIO AMPLIFIER Given: Power Output Load Impedance GENERALIZED AUDIO POWER AMPLIFIER DESIGN The system designer usually knows some of the following parameters when starting an audio amplifier design: Desired Power Output Input Impedance Maximum Supply Voltage 1V(max) Input Impedance 100 k 20 Hz-20 kHz 0.25 dB Equations (5), (6) give: Iopeak = 3.16A 40W/8 Vopeak = 25.3V Therefore the supply required is: 30.3V @3.16A With 15% regulation and high line the final supply voltage is 38.3V using Equation (7). At this point it is a good idea to check the Power Output vs Supply Voltage to ensure that the required output power is obtainable from the device while maintaining low THD + N. It is also good to check the Power Dissipation vs Supply Voltage to ensure that the device can handle the internal power dissipation. At the same time designing in a relatively practical sized heat sink with a low thermal resistance is also important. Refer to Typical Performance Characteristics graphs and the Thermal Considerations section for more information. The minimum gain from Equation (8) is: AV 18 We select a gain of 21 (Non-Inverting Amplifier); resulting in a sensitivity of 894 mV. Letting RIN equal 100 k gives the required input impedance, however, this would eliminate the "volume control" unless an additional input impedance was placed in series with the 10 k potentiometer that is depicted in Figure 1. Adding the additional 100 k resistor would ensure the minimum required input impedance. For low DC offsets at the output we let Rf1 = 100 k. Solving for Ri (Non-Inverting Amplifier) gives the following: Ri = Rf1/(AV - 1) = 100k/(21 - 1) = 5 k; use 5.1 k The bandwidth requirement must be stated as a pole, i.e., the 3 dB frequency. Five times away from a pole give 0.17 dB down, which is better than the required 0.25 dB. Therefore: fL = 20 Hz/5 = 4 Hz fH = 20 kHz x 5 = 100 kHz At this point, it is a good idea to ensure that the Gain Bandwidth Product for the part will provide the designed gain out to the upper 3 dB point of 100 kHz. This is why the minimum GBWP of the LM3875 is important. GBWP = AV x f3 dB = 21 x 100 kHz = 2.1 MHz GBWP = 2.0 MHz (min) for LM3875 Solving for the low frequency roll-off capacitor, Ci, we have: Ci > 1/(2 Ri fL) = 7.8 F; use 10 F. Load Impedance Bandwidth The power output and load impedance determine the power supply requirements, however, depending upon the application some system designers may be limited to certain maximum supply voltages. If the designer does have a power supply limitation, he should choose a practical load impedance which would allow the amplifier to provide the desired output power, keeping in mind the current limiting capabilities of the device. In any case, the output signal swing and current are found from (where PO is the average output power): (5) (6) To determine the maximum supply voltage the following parameters must be considered. Add the dropout voltage (5 volts for LM3875) to the peak output swing, Vopeak, to get the supply rail value, (i.e. + Vopeak + Vod) at a current of Iopeak). The regulation of the supply determines the unloaded voltage, usually about 15% higher. Supply voltage will also rise 10% during high line conditions. Therefore, the maximum supply voltage is obtained from the following equation: max. supplies (Vopeak + Vod(1 + regulation)(1.1) (7) The input sensitivity and the output power specs determine the minimum required gain as depicted below: (8) Normally the gain is set between 20 and 200; for a 40W, 8 audio amplifier this results in a sensitivity of 894 mV and 89 mV, respectively. Although higher gain amplifiers provide greater output power and dynamic headroom capabilities, there are certain shortcomings that go along with the so called "gain". The input referred noise floor is increased and hence the SNR is worse. With the increase in gain, there is also a reduction of the power bandwidth which results in a decrease in feedback thus not allowing the amplifier to rewww.national.com 8 Input Level Bandwidth Input Level 40W 16 Input Offset Voltage: The absolute value of the voltage which must be applied between the input terminals through two equal resistances to obtain zero output voltage and current. Input Bias Current: The absolute value of the average of the two input currents with the output voltage and current at zero. Input Offset Current: The absolute value of the difference in the two input currents with the output voltage and current at zero. Input Common-Mode Voltage Range (or Input Voltage Range): The range of voltages on the input terminals for which the amplifier is operational. Note that the specifications are not guaranteed over the full common-mode voltage range unless specifically stated. Output-Current Limit: The output current with a fixed output voltage and a large input overdrive. The limiting current drops with time once SPiKe protection circuitry is activated. Output Saturation Threshold (Clipping Point): The output swing limit for a specified input drive beyond that required for zero output. It is measured with respect to the supply to which the output is swinging. Common-Mode Rejection: The ratio of the input commonmode voltage range to the peak-to-peak change in input offset voltage over this range. Power Supply Rejection: The ratio of the change in input offset voltage to the change in power supply voltages producing it. Quiescent Supply Current: The current required from the power supply to operate the amplifier with no load and the output voltage and current at zero. Slew Rate: The internally limited rate of change in output voltage with a large amplitude step function applied to the input. Class B Amplifier: The most common type of audio power amplifier that consists of two output devices each of which conducts for 180 of the input cycle. The LM3875 is a Quasi-AB type amplifier. Crossover Distortion: Distortion caused in the output stage of a class B amplifier. It can result from inadequate bias current providing a dead zone where the output does not respond to the input as the input cycle goes through its zero crossing point. Also for ICs an inadequate frequency response of the output PNP device can cause a turn-on delay giving crossover distortion on the negative going transistion through zero crossing at the higher audio frequencies. THD + N: Total Harmonic Distortion plus Noise refers to the measurement technique in which the fundamental component is removed by a bandreject (notch) filter and all remaining energy is measured including harmonics and noise. Signal-to-Noise Ratio: The ratio of a system's output signal level to the system's output noise level obtained in the absence of a signal. The output reference signal is either specified or measured at a specified distortion level. Continuous Average Output Power: The minimum sine wave continuous average power output in watts (or dBW) that can be delivered into the rated load, over the rated bandwidth, at the rated maximum total harmonic distortion. Music Power: A measurement of the peak output power capability of an amplifier with either a signal duration sufficiently short that the amplifier power supply does not sag during the measurement, or when high quality external power supplies are used. This measurement (an IHF standard) assumes that with normal music program material the amplifier power supplies will sag insignificantly. Peak Power: Most commonly referred to as the power output capability of an amplifier that can be delivered to the load; specified by the part's maximum voltage swing. Output Resistance: The ratio of the change in output voltage to the change in output current with the output around zero. Power Dissipation Rating: The power that can be dissipated for a specified time interval without activating the protection circuitry. For time intervals in excess of 100 ms, dissipation capability is determined by heat sinking of the IC package rather than by the IC itself. Thermal Resistance: The peak, junction-temperature rise, per unit of internal power dissipation (units in C/W), above the case temperature as measured at the center of the package bottom. The DC thermal resistance applies when one output transistor is operating continuously. The AC thermal resistance applies with the output transistors conducting alternately at a high enough frequency that the peak capability of neither transistor is exceeded. Power Bandwidth: The power bandwidth of an audio amplifier is the frequency range over which the amplifier voltage gain does not fall below 0.707 of the flat band voltage gain specified for a given load and output power. Power bandwidth also can be measured by the frequencies at which a specified level of distortion is obtained while the amplifier delivers a power output 3 dB below the rated output. For example, an amplifier rated at 60W with 0.25% THD + N, would make its power bandwidth measured as the difference between the upper and lower frequencies at which 0.25% distortion was obtained while the amplifier was delivering 30W. Gain-Bandwidth Product: The Gain-Bandwidth Product is a way of predicting the high-frequency usefulness of an op amp. The Gain-Bandwidth Product is sometimes called the unity-gain frequency or unity-gain cross frequency because the open-loop gain characteristic passes through or crosses unity gain at this frequency. Simply, we have the following relationship: ACL1 x f1 = ACL2 x f2 Assuming that at unity-gain (ACL1 = 1 or 0 dB) fu = f1 = GBWP, then we have the following: GBWP = ACL2 x f2 This says that once fu (GBWP) is known for an amplifier, then the open-loop gain can be found at any frequency. This 17 www.national.com LM3875 Headroom: The margin between an actual signal operating level (usually the power rating of the amplifier with particular supply voltages, a rated load value, and a rated THD + N figure) and the level just before clipping distortion occurs, expressed in decibels. Large Signal Voltage Gain: The ratio of the output voltage swing to the differential input voltage required to drive the output from zero to either swing limit. The output swing limit is the supply voltage less a specified quasi-saturation voltage. A pulse of short enough duration to minimize thermal effects is used as a measurement signal. Definition of Terms LM3875 Definition of Terms This refers to a weighted noise measurement for a Dolby B type noise reduction system. A filter characteristic is used that gives a closer correlation of the measurement with the subjective annoyance of noise to the ear. Measurements made with this filter cannot necessarily be related to unweighted noise measurements by some fixed conversion factor since the answers obtained will depend on the spectrum of the noise source. (Continued) is also an excellent equation to determine the 3 dB point of a closed-loop gain, assuming that you know the GBWP of the device. Refer to the diagram below. Bi-amplification: The technique of splitting the audio frequency spectrum into two sections and using individual power amplifiers to drive a separate woofer and tweeter. Crossover frequencies for the amplifiers usually vary between 500 Hz and 1600 Hz. "Biamping" has the advantages of allowing smaller power amps to produce a given sound pressure level and reducing distortion effects produced by overdrive in one part of the frequency spectrum affecting the other part. C.C.I.R./A.R.M.: Literally: International Radio Consultative Average Responding Meter S.P.L.: Sound Pressure Level -- usually measured with a microphone/meter combination calibrated to a pressure level of 0.0002 Bars (approximately the threshold hearing level). S.P.L. = 20 Log 10P/0.0002 dB Where P is the R.M.S sound pressure in microbars. (1 Bar = 1 atmosphere = 14.5 lb./in2 = 194 dB S.P.L.). Committee 01144914 FIGURE 3. www.national.com 18 LM3875 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LM3875T NS Package Number TA11B Order Number LM3875TF NS Package Number TF11B 19 www.national.com LM3875 Overture Audio Power Amplifier Series High-Performance 56W Audio Power Amplifier Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated