Supertex inc.
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
HV2601
Features
►HVCMOS technology for high performance
►16-channel high voltage analog switch
►3.3V input logic level compatible
►20MHz data shift clock frequency
►Very low quiescent power dissipation (-10µA)
►Low parasitic capacitance
►DC to 50MHz small signal frequency response
►-60dB typical OFF-isolation at 5.0MHz
►CMOS logic circuitry for low power
►Excellent noise immunity
►Cascadable serial data register with latches
►Flexible operating supply voltages
Applications
►Medical ultrasound imaging
►NDT metal aw detection
►Piezoelectric transducer drivers
►Optical MEMS modules
General Description
The Supertex HV2601 is a low charge injection 16-channel
high voltage analog switch integrated circuit (IC) intended for
use in applications requiring high voltage switching controlled
by low voltage control signals, such as medical ultrasound
imaging and other piezoelectric transducer drivers.
Input data are shifted into a 16-bit shift register that can then
be retained in a 16-bit latch. To reduce any possible clock
feed-through noise, the latch enable bar should be left high
until all bits are clocked in. Data are clocked in during the
rising edge of the clock. Using HVCMOS technology, this
device combines high voltage bilateral DMOS switches and
low power CMOS logic to provide efcient control of high
voltage analog signals.
The device is suitable for various combinations of high
voltage supplies, e.g., VPP/VNN: +40V/-160V, +100V/-100V,
and +160V/-40V.
Block Diagram
Low Charge Injection 16-Channel
High Voltage Analog Switch
Latches
Level
Shifters Output
Switches
SW2
16-Bit
Shift
Register
VPP
VNN
CLR
LE
VDD GND
SW14
SW15
SW1
SW0
D
LE
CLR
D
LE
CLR
D
LE
CLR
D
LE
CLR
D
LE
CLR
DOUT
CLK
DIN
2
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
YY = Year Sealed
WW = Week Sealed
L = Lot Number
C = Country of Origin*
A = Assembler ID*
= “Green” Packaging
*May be part of top marking
Top Marking
Bottom Marking
YYWW
HV2601FG
LLLLLLLLL
CCCCCCCC
AAA
Absolute Maximum Ratings
Absolute Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation under these conditions is not implied. Continuous operation of the device at
the absolute rating level may affect device reliability. All voltages are referenced to device ground.
Parameter Value
VDD logic supply -0.5V to +7.0V
VPP - VNN differential supply 220V
VPP positive supply -0.5V to VNN+200V
VNN negative supply +0.5V to -200V
Logic input voltage -0.5V to VDD +0.3V
Analog signal range VNN to VPP
Peak analog signal current/channel 3.0A
Storage temperature -65°C to 150°C
Power dissipation:
42-Ball Bumped Die (BD)
48-Lead LQFP (FG)
48-Ball fpBGA (GA)
1.5W
1.0W
1.0W
Product Marking
48-Lead LQFP (FG)
-G indicates package is RoHS compliant (‘Green’).
Bumped Die package is RoHS compliant (‘Green’).
M936 species product in tape and reel.
Pin Congurations
Ordering Information
Device
Package Options
42-Ball Bumped Die
5.29x5.30mm body
1.01mm height (max)
0.52 / 0.60mm pitch
48-Lead LQFP
7.00x7.00mm body
1.60mm height (max)
0.50mm pitch
48-Ball fpBGA
7.00x8.00mm body
1.16mm height (max)
0.75mm pitch
HV2601 HV2601BD M936 HV2601FG-G HV2601GA-G
Sym Parameter Value
VDD Logic power supply voltage 3.0V to 5.5V
VPP Positive high voltage supply +40V to VNN +200V
VNN Negative high voltage supply -40V to -160V
VIH High level input voltage 0.9VDD to VDD
VIL Low level input voltage 0V to 0.1VDD
VSIG
Analog signal voltage
peak-to-peak VNN+10V to VPP-10V
TAOperating free air temperature 0°C to 70°C
Recommended Operating Conditions
Notes:
1. Power up/down sequence is arbitrary except GND must be powered-up rst
and powered-down last.
2. VSIG must be within VNN and VPP or oating during power up/down transition.
3. Rise and fall times of power supplies VDD, VPP
, and VNN should not be less than
1.0msec.
42-Ball Bumped Die (BD)
YY = Year Sealed
WW = Week Sealed
L = Lot Number
LLLLLLL
YYWW
HV2601BD
Package may or may not include the following marks: Si or
Package may or may not include the following marks: Si or
48-Lead LQFP (FG)
(top view)
1
48
42-Ball Bumped Die (BD)
(top view)
1
2
3
8
9
10 12
13
4
5
6
7
11
18 17 16 15 14
25
26
21
22
23
24
19
20
41
42
33
34
39
40
31
32
37
38
29
30
35
36
27
28
YY = Year Sealed
WW = Week Sealed
L = Lot Number
= “Green” Packaging
YYWW
HV2601GA
LLLLLLLLL
A
B
C
D
E
F
G
H
1 2 3 4 5 6
48-Ball fpBGA (GA)
(top view)
48-Ball fpBGA (GA)
Packages may or may not include the following marks: Si or
3
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
Sym Parameter
0°C +25°C +70°C
Units Conditions
Min Max Min Typ Max Min Max
RONS
Small signal switch
ON-resistance
- 30 - 26 38 - 48
Ω
ISIG = 5.0mA VPP = +40V
VNN = -160V
- 25 - 22 27 - 32 ISIG = 200mA
- 25 - 22 27 - 30 ISIG = 5.0mA VPP = +100V
VNN = -100V
- 18 - 18 24 - 27 ISIG = 200mA
- 23 - 20 25 - 30 ISIG = 5.0mA VPP = +160V
VNN = -40V
- 22 - 16 25 - 27 ISIG = 200mA
∆RONS
Small signal switch
ON-resistance matching - 20 - 5.0 20 - 20 % ISIG = 5.0mA, VPP = +100V,
VNN = -100V
RONL
Large signal switch
ON-resistance - - - 15 - - - ΩVSIG=VPP -10V, ISIG = 1.0A
ISOL
Switch OFF leakage per
switch* - 5.0 - 1.0 10 - 15 µA VSIG = VPP -10V and VNN +10V
VOS
DC offset switch OFF* - 300 - 100 300 - 300 mV 100kΩ load
DC offset switch ON* - 500 - 100 500 - 500 mV
IPPQ
Quiescent VPP supply
current - - - 10 50 - - µA All switches OFF
INNQ
Quiescent VNN supply
current - - - -10 -50 - - µA All switches OFF
IPPQ
Quiescent VPP supply
current - - - 10 50 - - µA All switches ON, ISW = 5.0mA
INNQ
Quiescent VNN supply
current - - - -10 -50 - - µA All switches ON, ISW = 5.0mA
ISW Switch output peak current - 3.0 - 3.0 2.0 - 2.0 A VSIG duty cycle < 0.1%
fSW Output switching frequency - - - - 50 - - kHz Duty cycle = 50%
IPP Average VPP supply current
- 6.5 - - 7.0 - 8.0
mA
VPP = +40V
VNN = -160V All output
switches are
turning ON and
OFF at 50kHz
with no load.
VPP = +100V
VNN = -100V
- 4.0 - - 5.5 - 5.5
VPP = +160V
VNN = -40V
- 4.0 - - 5.0 - 5.5
INN Average VNN supply current
- 6.5 - - 7.0 - 8.0
mA
VPP = +40V
VNN = -160V All output
switches are
turning ON and
OFF at 50kHz
with no load.
VPP = +100V
VNN = -100V
- 4.0 - - 5.0 - 5.5
VPP = +160V
VNN=-40V
- 4.0 - - 5.0 - 5.5
IDD Average VDD supply current - 4.0 - - 4.0 - 4.0 mA fCLK = 5.0MHz, VDD = 5.0V
IDDQ
Quiescent VDD supply
current - 10 - - 10 - 10 µA All logic inputs are static
ISOR Data out source current 0.45 - 0.45 0.70 - 0.40 - mA VOUT = VDD -0.7V
ISINK Data out sink current 0.45 - 0.45 0.70 - 0.40 - mA VOUT = 0.7V
CIN Logic input capacitance - 10 - - 10 - 10 pF ---
DC Electrical Characteristics
(over recommended operating conditions unless otherwise noted)
* See Test Circuits on page 5
4
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
AC Electrical Characteristics
(over recommended operating conditions, VDD= 5.0V, tR= tF ≤ 5ns, 50% duty cycle, CLOAD= 20pF unless otherwise noted)
Sym Parameter 0°C +25°C +70°C Units Conditions
Min Max Min Typ Max Min Max
tSD Set up time before LE rises 25 - 25 - - 25 - ns ---
tWLE Time width of LE
56 - - 56 - 56 -
ns
VDD = 3.0V
12 - - 12 - 12 - VDD = 5.0V
tDO Clock delay time to data out
50 100 50 78 100 50 100
ns
VDD = 3.0V
15 40 15 30 40 15 40 VDD= 5.0V
tWCLR Time width of CLR 55 - 55 - - 55 - ns ---
tSU Set up time data to clock
21 - - 21 - 21 -
ns
VDD= 3.0V
7 - - 7 - 7 - VDD= 5.0V
tHHold time data from clock 2 - 2 - - 2 - ns VDD= 3.0 or 5.0V
fCLK Clock frequency
- 8 - - 8 - 8
MHz
VDD= 3.0V
- 20 - - 20 - 20 VDD= 5.0V
tR,tFClock rise and fall times - 50 - - 50 - 50 ns ---
TON Turn ON time* - 5.0 - - 5.0 - 5.0 µs VSIG = VPP -10V, RLOAD = 10kΩ
TOFF Turn OFF time* - 5.0 - - 5.0 - 5.0 µs VSIG = VPP -10V, RLOAD = 10kΩ
dv/dt Maximum VSIG slew rate
- 20 - - 20 - 20
v/ns
VPP = +40V, VNN = -160V
- 20 - - 20 - 20 VPP = +100V, VNN = -100V
- 20 - - 20 - 20 VPP = +160V, VNN = -40V
KOOFF isolation*
-30 - -30 -33 - -30 -
dB
f = 5.0MHz, 1kΩ//15pF load
-58 - -58 - - -58 - f = 5.0MHz, 50Ω load
KCR Switch crosstalk* -60 - -60 -70 - -60 - dB f = 5.0MHz, 50Ω load
IID
Output switch isolation
diode current - 300 - - 300 300 mA 300ns pulse width,
2.0% duty cycle
CSG(OFF) OFF capacitance SW to GND 5.0 17 5.0 12 17 5.0 17 pF 0V, f = 1.0MHz
CSG(ON) ON capacitance SW to GND 25 50 25 38 50 25 50 pF 0V, f = 1.0MHz
+VSPK
Output voltage spike*
- - - - 150 - -
mV
VPP = +40V, VNN = -160V,
RLOAD = 50Ω
-VSPK
+VSPK - - - - 150 - - VPP = +100V, VNN = -100V,
RLOAD = 50Ω
-VSPK
+VSPK - - - - 150 - - VPP = +160V, VNN = -40V,
RLOAD = 50Ω
-VSPK
QC Charge injection*
- - - 820 - - -
pC
VPP= +40V, VNN= -160V, VSIG= 0V
- - - 600 - - - VPP= +100V, VNN= -100V, VSIG= 0V
- - - 350 - - - VPP= +160V, VNN= -40V, VSIG= 0V
* See Test Circuits on page 5
5
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
Test Circuits
DC Offset Switch
ON/OFF
V
PP
5V
V
NN
VPP
VNN
VDD
GND
V
OUT
T
ON
/T
OFF
Test Circuit
5V
GND
V
PP
-10V
10kΩ
V
OUT
Output Switch
Isolation Diode Current
I
ID
5V
GND
V
NN
V
SIG
Switch Crosstalk
V
IN
= 10V
P-P
@5MHz
NC
5V
GND
50Ω
Output Voltage Spike
5V
GND
V
OUT
1kΩ
R
LOAD
50Ω
+V
SPK
–V
SPK
OFF Isolation
K
O
= 20Log V
OUT
V
IN
V
IN
= 10V
P-P
@5MHz
5V
GND
V
OUT
50Ω
R
LOAD
R
LOAD
V
PP
V
NN
VPP
VNN
VDD
V
PP
V
NN
VPP
VNN
VDD
V
PP
V
NN
VPP
VNN
VDD
V
PP
V
NN
VPP
VNN
VDD
V
PP
V
NN
VPP
VNN
VDD
K
CR
= 20Log V
OUT
V
IN
V
PP
-10V
Switch Off Leakage
per Switch
RGND
Open
Q = 1000pF x ΔV
OUT
Charge Injection
5V
GND
V
PP
V
NN
VPP
VNN
VDD
V
PP
5V
V
NN
VPP
VNN
VDD
Open
I
SOL
GND
V
OUT
ΔV
OUT
1000pF
100kΩ
R
LOAD
V
SIG
6
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
Logic Function Table
Notes:
1. The 16 switches operate independently.
2. Serial data is clocked in on the L to H transition of the CLK.
3. All 16 switches go to a state retaining their latched condition at the rising edge of LE. When LE is low the shift registers data ow through the latch.
4. DOUT is high when data in the shift register 15 is high.
5. Shift registers clocking has no effect on the switch states if LE is high.
6. The CLR clear input overrides all other inputs.
Logic Timing Waveforms
DATA IN
DIN
LE
CLOCK
CLK
DATA OUT
DOUT
OFF
ON
V
OUT
(typ)
50% 50%
50% 50%
t
WLE
t
SD
t
SU
t
h
50%
50%
t
OFF
50%
t
DO
DO
t
ON
t
WCL
CLR
D
N+1
D
N
D
N-1
50% 50%
90%
10%
D0 D1 ... D7 D8 ... D15 LE CLR SW0 SW1 ... SW7 SW8 ... SW15
L -
...
- -
...
- L L OFF -
...
- -
...
-
H - - - - L L ON - - - -
- L - - - L L - OFF - - -
- H - - - L L - ON - - -
- - - - - L L - - - - -
- - - - - L L - - OFF - -
- - L - - L L - - ON - -
- - H - - L L - - - OFF -
- - - L - L L - - - ON -
- - - H - L L - - - - -
- - - - - L L - - - - -
- - - - - L L - - - - -
- - - - - L L - - - - -
- - - - - L L - - - - -
- - - - L L L - - - - OFF
- - - - H L L - - - - ON
X X X X X X X H L HOLD PREVIOUS STATE
X X X X X X X X H ALL SWITCHES OFF
7
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
Ball # Ball Name Ball Coordinates*
X Y
1 NC +2100.00 -2239.50
2 VPP -1500.00 -2239.50
3 VNN -2100.00 -2239.50
4 DOUT +1200.00 -1719.75
5 CLR +600.00 -1719.75
6 CLK 0.00 -1719.75
7 GND -600.00 -1719.75
8 SW15A +1500.00 -1200.00
9 SW15B +900.00 -1200.00
10 LE +300.00 -1200.00
11 VDD -300.00 -1200.00
12 SW0A -900.00 -1200.00
13 SW0B -1500.00 -1200.00
14 SW14A +1500.00 -600.00
15 SW14B +900.00 -600.00
16 DIN 0.00 -680.25
17 SW1A -900.00 -600.00
18 SW1B -1500.00 -600.00
19 SW13A +1500.00 0.00
20 SW13B +900.00 0.00
21 SW2A -900.00 0.00
Ball # Ball Name Ball Coordinates*
X Y
22 SW2B -1500.00 0.00
23 SW12A +1500.00 +600.00
24 SW12B +900.00 +600.00
25 SW3A -900.00 +600.00
26 SW3B -1500.00 +600.00
27 SW11A +2100.00 +1200.00
28 SW11B +1500.00 +1200.00
29 SW9B +900.00 +1200.00
30 SW8B +300.00 +1200.00
31 SW7A -300.00 +1200.00
32 SW6A -900.00 +1200.00
33 SW4A -1500.00 +1200.00
34 SW4B -2100.00 +1200.00
35 SW10B +2100.00 +1800.00
36 SW10A +1500.00 +1800.00
37 SW9A +900.00 +1800.00
38 SW8A +300.00 +1800.00
39 SW7B -300.00 +1800.00
40 SW6B -900.00 +1800.00
41 SW5B -1500.00 +1800.00
42 SW5A -2100.00 +1800.00
Ball Description
42-Ball Bumped Die Package Outline (BD)
Note:
* Referenced from center of package (µm).
8
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
Pin Description
48-Lead LQFP (FG)
Pin # Function
1 NC
2 NC
3 SW4B
4 SW4A
5 SW3B
6 SW3A
7 SW2B
8 SW2A
9 SW1B
10 SW1A
11 SW0B
12 SW0A
Pin # Function
13 VNN
14 NC
15 VPP
16 NC
17 GND
18 VDD
19 DIN
20 CLK
21 LE
22 CLR
23 DOUT
24 NC
Pin # Function
25 SW15B
26 SW15A
27 SW14B
28 SW14A
29 SW13B
30 SW13A
31 SW12B
32 SW12A
33 SW11B
34 SW11A
35 NC
36 NC
Pin # Function
37 SW10B
38 SW10A
39 SW9B
40 SW9A
41 SW8B
42 SW8A
43 SW7B
44 SW7A
45 SW6B
46 SW6A
47 SW5B
48 SW5A
Ball # Function
A1 SW5A
A2 SW5B
A3 SW7A
A4 SW7B
A5 SW9A
A6 SW9B
B1 SW6A
B2 SW6B
B3 SW8A
B4 SW8B
B5 SW10A
B6 SW10B
Ball # Function
C1 SW4B
C2 SW3B
C3 SW2B
C4 SW13A
C5 SW12A
C6 SW11A
D1 SW4A
D2 SW3A
D3 SW2A
D4 SW13B
D5 SW12B
D6 SW11B
Ball # Function
E1 SW1B
E2 SW0B
E3 SW15B
E4 SW15A
E5 SW14B
E6 SW14A
F1 SW1A
F2 SW0A
F3 NC
F4 NC
F5 VDD
F6 NC
Ball # Function
G1 NC
G2 GND
G3 NC
G4 DIN
G5 CLK
G6 DOUT
H1 VNN
H2 NC
H3 VPP
H4 NC
H5 LE
H6 CLR
NC = No Internal Connection
Pin Conguration
48-Ball fpBGA (GA)
9
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
42-Ball Bumped Die Package Outline (BD)
5.29x5.30mm body, 1.01mm height (max), 0.52 / 0.60mm pitch
Symbol A A1 A2 b D D1 E E1 E2 e e1
Dimension
(mm)
MIN 0.89 0.21 0.68 0.29 5.19 4.20
BSC
5.20 4.04
BSC
0.68
BSC
0.60
BSC
0.52
BSC
NOM 0.95 0.24 0.71 0.32 5.29 5.30
MAX 1.01 0.27 0.74 0.35 5.39 5.40
Drawings not to scale.
Supertex Doc. #: DSPD-42BumpedDieBD, Version A030211.
Top View View B
Side View
A2
A1
Seating
Plane
View A View B
Bottom View
D
View A
b
E
A
Note 1
(Ball 1
Index Area
D/4 x E/4)
0,0
E1
e1
E2
e D1
e
e1
e1
e
C/L
C/L
1
42
1
42
Notes:
1. Ball 1 identier must be located in the index area indicated. Ball 1 identier can be: a molded mark/identier; an embedded metal marker; or a
printed indicator.
10
HV2601
Supertex inc. ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 ● Tel: 408-222-8888 ● www.supertex.com
48-Lead LQFP Package Outline (FG)
7.00x7.00mm body, 1.60mm height (max), 0.50mm pitch
Symbol A A1 A2 b D D1 E E1 e L L1 L2 θ
Dimension
(mm)
MIN 1.40* 0.05 1.35 0.17 8.80* 6.80* 8.80* 6.80*
0.50
BSC
0.45
1.00
REF
0.25
BSC
0O
NOM - - 1.40 0.22 9.00 7.00 9.00 7.00 0.60 3.5O
MAX 1.60 0.15 1.45 0.27 9.20* 7.20* 9.20* 7.20* 0.75 7O
JEDEC Registration MS-026, Variation BBC, Issue D, Jan. 2001.
* This dimension is not specied in the JEDEC drawing.
Drawings are not to scale.
Supertex Doc. #: DSPD-48LQFPFG Version, D041309.
1
Seating
Plane
Gauge
Plane
θ
L
L1
L2
View B
View B
Seating
Plane
Top View
D
D1
E
E1
b e
Side View
A2
A
A1
Note 1
(Index Area
D1/4 x E1/4)
48
Note:
1. A Pin 1 identier must be located in the index area indicated. The Pin 1 identier can be: a molded mark/identier; an embedded metal marker; or
a printed indicator.
Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives
an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability
to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and
specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com)
©2011 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited.
Supertex inc.
1235 Bordeaux Drive, Sunnyvale, CA
94089
Tel: 408-222-8888
www
.supertex.com
11
HV2601
(The package drawing(s) in this data sheet may not reect the most current specications. For the latest package outline
information go to http://www.supertex.com/packaging.html.)
Doc.# DSFP-HV2601
D092011
48-Ball fpBGA Package Outline (GA)
7.00x8.00mm body, 1.16mm height (max), 0.75mm pitch
Symbol A A1 A2 b D D1 E E1 e
Dimension
(mm)
MIN 0.86 0.18 0.68 0.25 6.90 3.75
BSC
7.90 5.25
BSC
0.75
BSC
NOM 1.01 0.23 0.78 0.30 7.00 8.00
MAX 1.16 0.28 0.88 0.35 7.10 8.10
Drawings not to scale.
Supertex Doc. #: DSPD-48fpBGAGA, Version C020309.
Top View View B
e
Side View
A2
A1
Seating
Plane
View A View B
Bottom View
D
View A
Φb
e
E
A
D1
E1
Note 1
(Ball A1
Index Area
D/4 x E/4)
Note 2
6 5 4 3 2 1
A
B
C
D
E
F
G
H
Notes:
1. Ball A1 identier must be located in the index area indicated. Ball A1 identier can be: a molded mark/identier; an embedded metal marker; or a
printed indicator.
2. Corner A1 identier (actual shape may vary).