SFP-1GBT-05 - Bel Fuse Inc.

SFP Copper Transceiver 10/100/1000Base-T SGMII

SFP-1GBT-05

Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com

page 1

REGULATORY AND STANDARDS COMPLIANCE

• Compliant with IEEE 802.3:2000

• FCC Part 15, Class A

• EN55022 Class A (CISPR 22 Class A)

• CE

• E55024 Immunity standard and NEBS 3 ESD

The Bel SFP-1GBT-05 transceiver is an internally configured 10/100/1000Base-T SFP that requires the host system to

provide SGMII interface. The PHY interfaces directly with SerDes interface. The host interface transmits and receives serial

data differentially at 1.25 Gbps. The copper interface is full featured as advertised full/half duplex and 1000Base-T wire speed.

APPLICATIONS

• 10/100/1000 Mbps data rate in excess of

100 meters of Category 5/5e cable

• Industrial temperature environments -40 ° to +85° C

• Networking equipment

• Switch-to-switch interface

• Routers

FEATURES / BENEFITS

• Designed with Broadcom’s BCM54616S chipset

(login at https://support.broadcom.com/Core/Login.aspx

for IC support)

• Complies with IEEE 802.3, 802.3u, and 802.3ab

specifications

• Conforms to Multi-Source Agreement (MSA) specifications

for SFP transceivers

• Supports IEEE 802.3u and IEEE 802.3ab auto–negotiation

features to allow networking equipment to automatically

determine and adjust the required settings

• Operates in extended temperature range of -40 ° to +85° C

• Automatically compensates for baseline wander by removing

the DC offset from the input signal

• Assembled with low EMI emissions IC and fully metallic

housings

• Automatic dependent interface (DI) crossover, eliminating the

need for crossover cables or cross-wire (MDIX) ports

• Bail latch provides ease of extraction

• Compact RJ45 connector assembly

• Data is scrambled to reduce radiated emission

• Power consumption is 610mW typical for 1000Base-T

• Power consumption is 320mW typical for 10Base-T and

100Base-Tx

• Fully RoHS compliant

• The BCM54616S physical layer IC (PHY) can be

accessed via I2C interface:

• PHY address = “ACh”

• EEPROM memory address = “A0h”

• SFP Transceiver identification is specified as “08h” for byte

6 in the EEPROM.

Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com

SFP Copper Transceiver 10/100/1000Base-T SGMII

SFP-1GBT-05

SFP-1BGT-05 MODULE SPECIFICATIONS

page 2

Parameter Symbol Min Typ Max Units Notes

Supply Voltage VDD3 3.12 3.3 3.46 V

Supply Current IS185 mA 1000Base-T

Supply Current IS98 mA 10Base-T and

100Base-Tx

SFP Host

Serial Interface

(TX/RX)

Symbol Min Typ Max Units Notes

Line Frequency FLINE 125 MHz

TX Output Impedance ZTX_OUT 100 ΩDifferential

RX Output Impedance ZRX_IN 100 ΩDifferential

Clock Frequency 25 MHz

Rise/Fall Time TR/TF4ns 20% - 80%

RMS Phase Jitter FJ1. 5 ps-rms FJ = 12 kHz to 20 MHz

offset frequency.

Environmental

Specifications Symbol Min Typ Max Units Notes

Operating Temp TOP -40 +85 °C Case temperature

Storage Temp TSTG -40 +85 °C Ambient temperature

RELIABILITY TESTING

Vibration Test: Reference MIL-STD-202, Method 204. Condition D.

Mechanical Shock: Reference IEC 68-2-27, Test Ea. Alternative MIL-STD-202, Method 213B, Condition A.

Temperature cycling and temperature-humidity-bias.

SFP Copper Transceiver 10/100/1000Base-T SGMII

SFP-1GBT-05

Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com

Pin Name Description

1VeeT Transmitter ground (common with receiver ground).

2TX Fault Transmitter fault is internally tied to transmit ground and is not sup-

ported.

3TX Disable Transmit disable. This pin is tied to PHY low power mode.

4MOD-DEF2 Signal SDA (data) of the two-wire serial ID interface.

5MOD-DEF1 Signal SCL (clock) of the two-wire serial ID interface.

6MOD-DEF0 This pin is internally tied to transmit ground.

7Rate Select Not implemented. This pin is floating internally.

8LOS Loss of signal indication.

9VeeR Receiver ground (common with transmitter ground).

10 VeeR Receiver ground (common with transmitter ground).

11 VeeR Receiver ground (common with transmitter ground).

12 RD- Differential receiver outputs. User to terminate to 100 Ω differential at

host. AC coupled.

13 RD+ Differential receiver outputs. User to terminate to 100 Ω differential at

host. AC coupled.

14 VeeR Receiver ground (common with transmitter ground).

15 VccR 3.3V power

16 VccT 3.3V power

17 VeeT Transmitter ground (common with receiver ground).

18 TD+ Differential transmitter outputs. User to terminate to 100 Ω differential at

host. AC coupled.

19 TD- User to terminate to 100 Ω differential at host. AC coupled.

20 VeeT Transmitter ground (common with receiver ground).

page 3

SFP HOST CONNECT ELECTRICAL INTERFACE AND PINS DESCRIPTIONS

Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com

SFP Copper Transceiver 10/100/1000Base-T SGMII

SFP-1GBT-05

• Rx_LOS is always ENABLE.

• High —> Not linked.

• Low —> Linked to link-partner.

• Customer’s MAC should be setup for SGMII interface with Auto-Negotiation and the preferred mode of operation. There

is no need for accessing the PHY registers of the Broadcom PHY of the SFP-1GBT-05 Transceiver.

• Bel’s Copper SFP-1GBT-05 Transceiver will automatically detect the advertised speed and mode of operation via the host

of the link-partner.

• Default is 1000Base-T (Full-Duplex or Half-Duplex).

• Bel’s Copper SFP-1GBT-05 Transceiver will automatically detect advertised 100Base-Tx speed and mode of

operations (Full-Duplex or Half-Duplex) from the MAC and link to its link-partner.

• Bel’s Copper SFP-1GBT-05 Transceiver will automatically detect advertised 10Base-T speed and mode of

operation (Full-Duplex or Half-Duplex) from the MAC and link to its link-partner.

Depending on the condition of the MAC configuration, the SFP-1GBT-05 Transceiver can also be forced to operate at the pre-

ferred speed and mode of operation by accessing the Broadcom PHY registers via “0xAC” address:

• 1000Base-T Full-Duplex and/or Half-Duplex — by default.

• Forcing the SFP-1GBT-05 to operate at 100Base-TX Full-Duplex and/or Half-Duplex:

1. Force Full-Duplex mode:

Write PHY register 00h to 0x2100h. (Force copper operate at 100Base-Tx Full-Duplex mode)

2. Force Half-Duplex mode:

Write PHY register 00h to 0x2000h. (Force copper operate at 100Base-Tx Half-Duplex mode)

3. Auto-Negotiation mode:

Write PHY register 09h to 0x0000. (Disable 1000Base-T ability)

Write PHY register 00h to 0x1340. (Restart Auto-Negotiation)

SGMII INSTALLATION GUIDE

Part Number Link Indicator on

Rx_LOS Pin

Auto-Negotiation

enabled by default Interface

SFP-1GBT-05 Ye s Ye s SGMII

(10/100/1000Base-T)

page 4

SFP Copper Transceiver 10/100/1000Base-T SGMII

SFP-1GBT-05

Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com

• Forcing the SFP-1GBT-05 to operate at 10Base-T Full-Duplex and/or half-duplex

1. Force full-duplex mode:

Write PHY register 00h to 0x0100h. (Force copper operate at 10Base-T Full-Duplex mode)

2. Force half-duplex mode:

Write PHY register 00h to 0x0000h. (Force copper operate at 10Base-T Half-Duplex mode)

3. Auto-Negotiation mode:

Write PHY register 09h to 0x0000. (Disable 1000Base-T ability)

Write PHY register 04h to 0x0061. (Disable 10Base-T and 100Base-Tx ability)

Write PHY register 00h to 0x1340. (Restart Auto-Negotiation)

SGMII-Copper to GBIC:

• If the GBIC Interface is required, Bel would recommend the SFP-1GBT-06 Transceiver for installation.

• However, SFP-1GBT-05 Transceiver can also be configured to operate in GBIC (1000Base-X to 1000Base-T) interface by

accessing the Broadcom PHY registers via “0xAC”:

1. Write register 18h, shadow 07h bit [7] = 0 (Disable RGMII mode)

2. Write register 1Ch, shadow 1Fh bit [0] = 1 (Enable fiber register bank)

3. Write register 00h, bit [11] = 1 (Power-down SerDes interface)

4. Write register 1Ch, shadow 1Fh bit [2:1] = 11 (Configure the BCM54616S in GBIC mode)

5. Write register 00h, bit [11] = 0 (Power-up SerDes interface)

6. Write register 1Ch, shadow 1Fh bit [0] = 0 (Enable copper register bank)

7. Write register 00h, bit [11] = 0 (power up copper interface)

MAC Auto-Negotiation vs. MAC without Auto-Negotiation:

In case of MAC does not have Auto-Negotiation capability, the Auto-Negotiation of the SFP-1GBT-05 can also be disabled by

clear the Broadcom PHY register bit12 to “0”, then attempt to install the Bel’s SFP Transceiver.

page 5

CORPORATE

Bel Fuse Inc.

206 Van Vorst Street

Jersey City, NJ 07302

Tel 201-432-0463

Fax 201-432-9542

www.belfuse.com

EUROPE

Bel Fuse Europe Ltd.

28 Turkey Court

Turkey Mill, Ashford Road

Maidstone ME14 5PP

United Kingdom

Tel 44-1622-757-395

Fax 44-1622-663-252

ASIA

Bel Fuse Ltd.

8F / 8 Luk Hop Street

San Po Kong

Kowloon, Hong Kong

Tel 852-2328-5515

Fax 852-2352-3706

www.belfuse.com

SFP Copper Transceiver 10/100/1000Base-T SGMII

SFP-1GBT-05

page 6

MECHANICAL