SPEC NO: DSAD1357 REV NO: V.5 DATE: AUG/04/2011 PAGE: 1 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1203000103
2.0x1.25mm INFRARED EMITTING DIODE
Part Number: AP2012F3C
Features
z2.0mmx1.25mm SMT LED,1.1mm thickness.
zMechanically and spectrally matched to the phototran-
sistor.
zPackage: 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
F3 Made with Gallium Arsenide Infrared Emitting diodes.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAD1357 REV NO: V.5 DATE: AUG/04/2011 PAGE: 2 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1203000103
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Radiant Intensity/ luminous flux: +/-15%.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Note:
1. Forward Voltage: +/-0.1V.
Note:
1. 1/100 Duty Cycle, 10μs Pulse Width.
Part No. Dice Lens Type
Viewing
Angle [1]
Min. Typ. 2θ1/2
AP2012F3C F3 (GaAs) Water Clear 1.2 3 120°
Po (mW/sr) [2]
@ 20mA
Parameter P/N Symbol Typ. Max. Units Test Conditions
Forward Voltage [1] F3 VF 1.2 1.6 V IF=20mA
Reverse Current F3 IR 10 uA VR = 5V
Capacitance F3 C 90 pF VF=0V;f=1MHz
Peak Spectral Wavelength F3 λP 940 nm IF=20mA
Spectral Bandwidth F3 Δλ1/2 50 nm IF=20mA
Parameter Symbol F3 Units
Power dissipation PD 80 mW
DC Forward Current IF 50 mA
Peak Forward Current [1] iFS 1.2 A
Reverse Voltage VR 5 V
Operating Temperature TA -40 To +85 °C
Storage Temperature TSTG -40 To +85 °C
SPEC NO: DSAD1357 REV NO: V.5 DATE: AUG/04/2011 PAGE: 3 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1203000103
AP2012F3C
SPEC NO: DSAD1357 REV NO: V.5 DATE: AUG/04/2011 PAGE: 4 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1203000103
AP2012F3C
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Specifications
(Units : mm)
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Reel Dimension
SPEC NO: DSAD1357 REV NO: V.5 DATE: AUG/04/2011 PAGE: 5 OF 5
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: C.H.Han ERP: 1203000103
PACKING & LABEL SPECIFICATIONS AP2012F3C
