Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Features * RF Bandwidth: 3365 to 3705 MHz * Ultra Low Phase Noise -98 dBc/Hz in Band Typ PLLS w/ Integrated VCO - SMT 7 7-1 * 24-bit Frequency Step Size, Resolution 3 Hz typ * Exact Frequency Mode * Figure of Merit (FOM) -227 dBc * Built-in Digital Self Test * < 180 fs rms Jitter (Integrated 100 Hz to 100 MHz SSB) * 40 Lead 6x6 mm SMT Package: 36 mm2 Typical Applications * Cellular/4G Infrastructure * Phased Array Applications * Repeaters and Femtocells * DDS Replacement * Communications Test Equipment * Very High Data Rate Radios * CATV Equipment Functional Diagram For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz General Description The HMC836LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) with an Integrated Voltage Controlled Oscillator (VCO). The PLL consists of an integrated low noise VCO with x2 output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD), a precision controlled charge pump, a low noise reference path divider and a fractional divider. The fractional PLL features an advanced delta-sigma modulator design that allows both fine step sizes and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster frequency hopping and low micro-phonics. Electrical Specifications, TA = +25 C VPPCP, VDDCP, VCC1, VCC2 = 5V 4%; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V 6% GNDCP = GNDLS = Ground Paddle = 0V Parameter Condition Min. Typ. Max. Units 1682.5 1852.5 MHz 3365 3705 MHz 9 dBm RF Output Characteristics VCO Frequency RF Output Frequency at f VCO x2 RF Output Power at f VCO x2 -1 VCO Tuning Sensitivity Measured at 2 GHz, 2V VCO Supply Pushing Measured at 2 GHz, 2V 6 15 -2 MHz/V 1.5 MHz/V RF Output 2nd Harmonic -25 dBc RF Output 3rd Harmonic -23 dBc RF Output 4th Harmonic -31 dBc RF Divider Characteristics 19-Bit N-Divider Range (Integer) 19-Bit N-Divider Range (Fractional) Max = 219 - 1 16 524,287 Fractional nominal divide ratio varies (-3 / +4) dynamically max 20 524,283 Synthesizer phase noise can degrade by about 5dB when operating with a reference frequency near the low end of this range. 10 50 200 MHz AC Coupled 1.5 2 3.3 Vpp 5 pF REF Input Characteristics Ref Input Frequency Ref Input Range Ref Input Capacitance 14-Bit R-Divider Range 1 16,383 7 PLLS w/ Integrated VCO - SMT For theory of operation and register map refer to the "PLLs with Integrated VCOs - RF VCOs Operating Guide". To view the Operating Guide, please visit www.hittite.com and choose HMC836LP6CE from the "Search by Part Number" pull down menu. Phase Detector (PD) PD Frequency Fractional Feedback Mode [1] 0.1 100 MHz PD Frequency Fractional Feedforward Mode (and Register 6 [17:16] = 10) [1] 0.1 80 MHz PD Frequency Integer Mode [1] 0.1 125 MHz Note 1: This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback mode, the maximum PFD rate = fvco/20 or 100MHz, whichever is less. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-2 HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Electrical Specifications (Continued) Parameter Condition Min. Typ. Max. Units 2.54 mA Charge Pump Output Current 0.02 Charge Pump Gain Step Size (5-Bits) PD/Charge Pump SSB Phase Noise 20 A 50 MHz Ref, Input Referred, 1 kHz -141 dBc/Hz 10 kHz add 1 dB for fractional -149 dBc/Hz 100 kHz add 3 dB for fractional -153 dBc/Hz Logic Inputs PLLS w/ Integrated VCO - SMT 7 VIH Input High Voltage DVDD3V-0.4 DVDD3V V VIL Input Low Voltage 0 0.4 V VOH Output High Voltage DVDD3V-0.4 DVDD3V V VOL Output Low Voltage 0 0.4 V 3.5 V Logic Outputs Power Supply Voltages Analog 3.3V Supplies AVDD, VCCHF, VCCPS, VCCPD, RVDD 3.0 3.3 DVDD3V 3.0 3.3 3.5 V VPPCP, VDDCP, VCC1, VCC2 4.8 5 5.2 V Digital Supply Analog 5V Supplies Power Supply Currents +5V Analog Charge Pump VPPCP, VDDCP 5.3 mA +5V VCO Core and PLL Buffer VCC2 56 mA +5V VCO RF Buffer VCC1 36 mA AVDD, VCCHF, VCCPS, VCCPD, RVDD 45 mA +3.3V Analog +3.3V Digital Power Down - Crystal Off Power Down - Crystal On, 100 MHz DVDD3V 6.5 mA Reg 01h=0, Crystal Not Clocked 10 A Reg 01h=0, Crystal Clocked 100 MHz 10 200 A Power on Reset Typical Reset Voltage on DVDD 700 DVDD Voltage for No Reset 1.5 Power on Reset Delay mV V 250 s -91 dBc/Hz 100 kHz Offset -111 dBc/Hz 1 MHz Offset -136 dBc/Hz 10 MHz Offset -157 dBc/Hz 100 MHz Offset -169 dBc/Hz VCO Open Loop SSB Phase Noise at fo = 1.75 GHz 10 kHz Offset Closed Loop Phase Noise PLL + VCO at fo = 3.5 GHz 7-3 Integer, 50 MHz PFD 1 kHz Offset -102 dBc/Hz Integer, 50 MHz PFD 10 kHz Offset -107 dBc/Hz Integer, 50 MHz PFD 100 kHz Offset -107 dBc/Hz For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Electrical Specifications (Continued) Parameter Condition Fractional, 50 MHz PFD Typ. Max. Units -197 dBc/Hz Fractional, 50 MHz PFD 10 kHz Offset -102 dBc/Hz Fractional, 50 MHz PFD 100 kHz Offset -102 dBc/Hz Figure of Merit Normalized 1 Hz Integer Mode Measured w/ 50 MHz PD at 30 kHz Offset -229 dBc/Hz Fractional Mode Measured w/ 50 MHz PD at 30 kHz Offset -227 dBc/Hz -70 -80 -80 PHASE NOISE (dBc/Hz) -90 -100 -110 -120 3300 MHz 3500 MHz 3700 MHz -140 -90 -100 -110 -120 -130 -150 -150 -160 -160 -170 100 1000 10 4 10 5 10 6 10 7 10 3365 MHz 3535 MHz 3705 MHz -140 -170 100 8 1000 FREQUENCY OFFSET (Hz) 10 4 10 5 10 6 10 7 10 8 FREQUENCY OFFSET (Hz) VCO Free Running SSB Phase Noise Typical Tuning Curves vs. Switch Position 0 fmax -40 n0 3300 MHz 3500 MHz 3700 MHz -60 kvco (MHz/V) PHASE NOISE (dBc/Hz) -20 -80 -100 -120 -140 fmin n2 n4 n6 n8 n10 n12 n14 n16 n18 n20 n22 n24 n26 n30 n30 PLLS w/ Integrated VCO - SMT -70 -130 7 Typical Closed Loop Fractional Mode, SSB Phase Noise [1] Closed Loop Integer Mode, SSB Phase Noise PHASE NOISE (dBc/Hz) Min. 1 kHz Offset n31 -160 -180 10 2 10 3 10 4 10 5 10 6 FREQUENCY OFFSET (Hz) 10 7 10 8 0 1 2 3 4 5 TUNING VOLTAGE (V) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: Contact factory for component values) 2mA Charge Pump, -385A Offset. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7-4 HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz 60 5 50 TUNING CAP 31 4 TUNING CAP 15 fmin 3 fmax 31 15 0 2 TUNING CAP 0 40 30 Typical Operating Range 20 1 10 0 0 0 1 2 Typical Output Power NORMALIZED PHASE NOISE (dBc/Hz) OUTPUT POWER (dBm) 8 6 4 0 +27C +85C -40C 3300 3400 3500 4 5 Figure of Merit 10 2 3 TUNING VOLTAGE (V) VCO FREQUENCY 7 PLLS w/ Integrated VCO - SMT Typical VCO Sensitivity vs. VCO Tune Voltage & CAP Setting @ fo [2] kvco (MHz/V) TUNE VOLTAGE AFTER CALIBRATION (V) Typical VCO Tuning Voltage After Calibration vs. VCO Frequency & CAP Setting [2] 3600 OUTPUT FREQUENCY (MHz) 3700 3800 -200 -210 Typ FOM vs Offset -220 FOM Floor FOM 1/f Noise -230 -240 10 2 10 3 10 4 10 5 10 6 FREQUENCY OFFSET (Hz) [1] Fractional Mode, 50 MHz Crystal, R=1, ~80 kHz Loop BW, (Loop filter values: Contact factory for component values) 2mA Charge Pump, -385A Offset. [2] The CAP setting is the digitally selectable VCO tank capacitor setting. This feature allows the nominal center frequency of the VCO to be adjusted by switching in/out VCO tank capacitors. 7-5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Pin Descriptions Function Description 1 AVDD DC Power Supply for analog circuitry. 2, 5, 6, 8, 9, 11 - 14, 18 - 22, 24, 26, 29, 34, 37, 38 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3 VPPCP Power Supply for charge pump analog section 4 CP Charge Pump Output 7 VDDCP Power Supply for the charge pump digital section 10 RVDD Reference Supply 15 XREFP Reference Oscillator Input 16 DVDD3V DC Power Supply for Digital (CMOS) Circuitry 17 CEN Chip Enable. Connect to logic high for normal operation. 23 VTUNE VCO Varactor. Tuning Port Input. 25 VCC2 VCO Analog Supply 2 27 VCC1 VCO Analog Supply 1 28 RFOUT RF Doubler Output 30 SEN PLL Serial Port Enable (CMOS) Logic Input 31 SDI PLL Serial Port Data (CMOS) Logic Input 32 SCK PLL Serial Port Clock (CMOS) Logic Input 33 LD_SDO Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO) 35 VCCHF DC Power Supply for Analog Circuitry 36 VCCPS DC Power Supply for Analog Prescaler 39 VCCPD DC Power Supply for Phase Detector BIAS External bypass decoupling for precision bias circuits. Note: 1.920V 20mV reference voltage (BIAS) is generated internally and cannot drive an external load. Must be measured with 10G meter such as Agilent 34410A, normal 10M DVM will read erroneously. 40 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 PLLS w/ Integrated VCO - SMT Pin Number 7-6 HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Absolute Maximum Ratings AVDD, RVDD, DVDD3V, VCCPD, VCCHF, VCCPS -0.3V to +3.6V VPPCP, VDDCP, VCC1 -0.3V to +5.8V VCC2 -0.3V to +5.5V Operating Temperature -40C to +85C Storage Temperature -65C to 125C Maximum Junction Temperature 125 C Thermal Resistance (RTH) (junction to ground paddle) 20 C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Reflow Soldering PLLS w/ Integrated VCO - SMT 7 Peak Temperature 260C Time at Peak Temperature 40 sec ESD Sensitivity (HBM) Class 1B Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [1] HMC836LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 H836 XXXX [1] 4-Digit lot number XXXX 7-7 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. Evaluation PCB Schematic To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC836LP6CE from the "Search by Part Number" pull down menu to view the product splash page. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com PLLS w/ Integrated VCO - SMT 7 7-8 HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz List of Materials for Evaluation PCB 127832 [1] PLLS w/ Integrated VCO - SMT 7 Item Description J1, J2 PCB Mount SMA RF Connector J3 Dual Row Terminal Strip J4 - J6 Connector Header C1, C15 - C17, C25 10 F Capacitor, 0805 Pkg. C2, C3, C6, C7, C11, C12, C14, C18, C27, C43, C45 0.47 F Capacitor, 0402 Pkg. C4, C13 22 pF Capacitor, 0402 Pkg. C5, C33 1000 pF Capacitor, 0402 Pkg. C8 8.2 pF Capacitor, 0402 Pkg. C19 - C24, C28, C30, C32, C34 0.1 F Capacitor, 0402 Pkg. C26 1.0 F Capacitor, 0603 Pkg. C35 3300 pF Capacitor, 0402 Pkg. C36 270 pF Capacitor, 0402 Pkg. C37, C38 68 pF Capacitor, 0402 Pkg. C39 - C42, C44 4.7 F Tantalum Capacitor, 0805 Pkg C46 27 pF Capacitor, 0402 Pkg. C47 47 pF Capacitor, 0402 Pkg. R1, R2, R11, R15, R18, R19, R21, R24 Zero Ohm Resistor, 0402 Pkg. R3, R4 1 Ohm Resistor, 0402 Pkg. R6 1 MOhm Resistor, 0402 Pkg. R8 22 Ohm Resistor, 0402 Pkg. R12, R20, R29 51 Ohm Resistor, 0402 Pkg. R13, R14, R30 220 kOhm Resistor, 0402 Pkg. R22, R25 20 kOhm Resistor, 0402 Pkg. R26 - R28 1k Ohm Resistor, 0402 Pkg. R32, R33 0 Ohm Resistor, 0805 Pkg. L1 10 nH Inductor, 0402 Pkg. L2 68 Ohm Resistor, 0402 Pkg. L3 4.7 nH Inductor, 0402 Pkg. L4 1.5 nH Inductor, 0402 Pkg. TP3, TP4 Test Point PC Compact SMT U1 HMC836LP6CE PLL with Integrated VCO U2 HMC860LP3E Low Noise Quad Linear Regulator Y1 3.3V, 50 MHz VCXO Crystal Oscillator PCB [2] 127729 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25FR and FR4 7-9 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC836LP6CE v07.1211 FRACTIONAL-N PLL WITH INTEGRATED VCO, 3365 - 3705 MHz Notes: PLLS w/ Integrated VCO - SMT 7 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 7 - 10 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC836LP6CE HMC836LP6CETR 129477-HMC836LP6CE