82545GM Gigabit Ethernet Controller Networking Silicon Datasheet Product Features * PCI/PCI-X -- PCI-X Revision 1.0a support for frequencies up to 133 MHz -- Multi-function PCI device -- PCI Revision 2.3 support for 32-bit wide or 64-bit wide interface at 33 MHz and 66 MHz * MAC -- IEEE 802.3x compliant flow control support with software controllable pause times and threshold values -- Programmable host memory receive buffers (256 Bytes to 16 Kbytes) and cache line size (16 Bytes to 256 Bytes) -- Wide, optimized internal data path architecture (128 bits) -- 64 Kbyte configurable Transmit and Receive FIFO buffers -- Optimized descriptor fetching and writeback mechanisms * PHY -- Integrated PHY for 10/100/1000 Mbps full and half duplex operation -- IEEE 802.3ab Auto-Negotiation support -- IEEE 802.3ab PHY compliance and compatibility * * * * -- PHY ability to automatically detect polarity and cable lengths and MDI versus MDI-X cable at all speeds Host Offloading -- Transmit and receive IP, TCP and UDP checksum off-loading capabilities -- Transmit TCP segmentation -- IEEE 802.1q VLAN support with VLAN tag insertion, stripping and packet filtering for up to 4096 VLAN tags -- Advanced packet filtering Manageability -- Manageability features on both ports: SMB port, ASF 1.0, ACPI, Wake on LAN, and PXE -- Compliance with PCI Power Management 1.1 and ACPI 2.0 register set compliant Four activity and link indication outputs that directly drive LEDs Lead-freea 364-pin Ball Grid Array (BGA). Devices that are lead-free are marked with a circled "e1" and have the product code: PCxxxxxx. a. This device is lead-free. That is, lead has not been intentionally added, but lead may still exist as an impurity at <1000 ppm. The Material Declaration Data Sheet, which includes lead impurity levels and the concentration of other Restriction on Hazardous Substances (RoHS)-banned materials, is available at: ftp://download.intel.com/design/packtech/material_content_IC_Package.pdf#pagemode=bookmarks In addition, this device has been tested and conforms to the same parametric specifications as previous versions of the device. For more information regarding lead-free products from Intel Corporation, contact your Intel Field Sales representative. 322559-001 Revision 2.2 August 2009 Revision History Revision Date 1.0 Mar 2003 1.1 Nov 2003 Description Initial release. Removed Confidential Status. Modified power specification tables in Section 4.0. Added a ball pad dimension drawing for the 82545GM device in Section 5.0. 1.2 Sept 2004 Corrected the nominal impedance values for the I/O cells from 50 kohms to a nominal impedance value of 120 kohms, with a minimum of 90 kohms and a maximum of 190 kohms. 1.5 June 2005 Added Specification Change and Specification Clarification information from the 82545GM Gigabit Ethernet Controller Specification Update. Added a more detailed AUX_PWR pin description. Added tristate and XOR non-JTAG test modes description. 2.0 Sept 2005 Added lead free information. 2.1 Feb 2007 Updated Table 3. 2.2 Aug 2009 Updated section 5.2, table 3. Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The 82545GM may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800548-4725 or by visiting Intel's website at http://www.intel.com. Intel(R) is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. Copyright (c) 2009 Intel Corporation. *Third-party brands and names are the property of their respective owners. Datasheet Networking Silicon -- 82545GM Contents 1.0 Introduction......................................................................................................................... 1 1.1 1.2 1.3 2.0 Additional 82545GM Features............................................................................................ 5 2.1 2.2 2.3 2.4 2.5 2.6 2.7 3.0 3.3 3.4 3.5 3.6 3.7 3.8 3.9 Signal Type Definitions.......................................................................................... 9 PCI Bus Interface .................................................................................................. 9 3.2.1 PCI Address, Data and Control Signals ................................................. 10 3.2.2 Arbitration Signals .................................................................................. 11 3.2.3 Interrupt Signal ....................................................................................... 11 3.2.4 System Signals....................................................................................... 12 3.2.5 Error Reporting Signals .......................................................................... 12 3.2.6 Power Management Signals .................................................................. 12 3.2.7 Impedance Compensation Signals......................................................... 13 3.2.8 SMB Signals........................................................................................... 13 EEPROM Interface Signals ................................................................................. 13 Flash Interface Signals........................................................................................ 14 Miscellaneous Signals......................................................................................... 14 3.5.1 LED Signals............................................................................................ 14 3.5.2 Software Definable Signals .................................................................... 14 PHY Signals ........................................................................................................ 15 3.6.1 Crystal Signals ....................................................................................... 15 3.6.2 Analog Signals ....................................................................................... 15 Serializer / Deserializer (SERDES) Signals ........................................................ 16 JTAG Test Interface Signals ............................................................................... 16 Power Supply Connections ................................................................................. 16 3.9.1 Power Support Signals........................................................................... 16 3.9.2 Digital Supplies....................................................................................... 17 3.9.3 Analog Supplies ..................................................................................... 17 3.9.4 Ground and No Connects....................................................................... 17 Test Port Functionality...................................................................................................... 19 4.1 4.2 Datasheet PCI ........................................................................................................................ 5 MAC Specific......................................................................................................... 5 PHY Specific ......................................................................................................... 5 Host Offloading...................................................................................................... 5 Manageability ........................................................................................................ 6 Additional Device................................................................................................... 6 Technology............................................................................................................ 7 Signal Descriptions.............................................................................................................9 3.1 3.2 4.0 Document Scope................................................................................................... 2 Reference Documents........................................................................................... 2 Product Code ........................................................................................................ 3 XOR Testing........................................................................................................ 19 4.1.1 XOR Tree Control and Operation........................................................... 19 4.1.2 Pins Tested ............................................................................................ 20 Tristate Mode ...................................................................................................... 21 4.2.1 Tristate Mode Control and Operation ..................................................... 21 iii 82545GM -- Networking Silicon 4.2.2 5.0 Voltage, Temperature, and Timing Specifications ........................................................... 23 5.1 5.2 5.3 5.4 5.5 5.6 6.0 Targeted Absolute Maximum Ratings ................................................................. 23 Recommended Operating Conditions ................................................................. 23 DC Specifications ................................................................................................ 24 AC Characteristics .............................................................................................. 28 Serial Interface Specifications ............................................................................. 29 Timing Specifications .......................................................................................... 30 5.6.1 PCI/PCI-X Bus Interface ........................................................................ 30 5.6.2 Link Interface Timing .............................................................................. 33 5.6.3 Flash Interface ....................................................................................... 36 5.6.4 EEPROM Interface................................................................................. 37 Package and Pinout Information ...................................................................................... 39 6.1 6.2 6.3 6.4 6.5 6.6 iv Tristate Mode Using JTAG (TAP)........................................................... 21 Device Identification ........................................................................................... 39 Lead-Free Device Identification .......................................................................... 40 Package Information ........................................................................................... 41 Thermal Specifications........................................................................................ 43 Ball Mapping Diagram ......................................................................................... 44 Pinout Information ............................................................................................... 44 Datasheet Networking Silicon -- 82545GM 1.0 Introduction The Intel(R) 82545GM Gigabit Ethernet Controller is a single, compact component with an integrated Gigabit Ethernet Media Access Control (MAC) and physical layer (PHY) functions. The Intel(R) 82545GM enables Gigabit Ethernet implementations in a very small area and can be used for desktop and workstation PC network designs as well as backplane applications with critical space constraints. The Intel(R) 82545GM integrates Intel's fourth generation gigabit MAC and PHY to provide a standard IEEE 802.3 Ethernet interface for 1000BASE-T, 100BASE-TX, and 10BASE-T applications (802.3, 802.3u, and 802.3ab). The controller is capable of transmitting and receiving data at rates of 1000 Mbps, 100 Mbps, or 10 Mbps. In addition, it provides a 64-bit wide direct Peripheral Component Interconnect (PCI) 2.3 and PCI-X 1.0a compliant interface capable of operating at frequencies up to 133 MHz. The Intel(R) 82545GM on-board System Management Bus (SMB) port enables network manageability implementations required by information technology personnel for remote control and alerting through the LAN. Using the SMB, management packets can be routed to or from a management processor. The SMB port enables industry standards, such as Intelligent Platform Management Interface (IPMI) and Alert Standard Format (ASF), to be implemented using the 82545GM. In addition, on chip ASF 1.0 circuitry provides alerting and remote control capabilities with standardized interfaces. The 82545GM Gigabit Ethernet Controller architecture is designed to deliver high performance and PCI/PCI-X bus efficiency. Wide internal data paths eliminate performance bottlenecks by efficiently handling large address and data words. Combining a parallel and pipe-lined logic architecture optimized for Gigabit Ethernet and independent transmit and receive queues, the 82545GM controller efficiently handles packets with minimum latency. The 82545GM controller includes advanced interrupt handling features to limit PCI bus traffic and a PCI interface that maximizes the use of bursts for efficient bus usage. The 82545GM is able to cache up to 64 packet descriptors in a single burst for efficient PCI bandwidth use. A large 64-Kbyte on-chip packet buffer maintains superior performance as available PCI bandwidth changes. By using hardware acceleration, the controller is able to offload tasks, such as checksum calculations and TCP segmentation, from the host processor. Datasheet 1 82545GM -- Networking Silicon The 82545GM is packaged in a 21 mm x 21 mm 364-ball grid array and footprint compatible with the Intel(R) 82544GC Gigabit Ethernet Controller. Figure 1. Gigabit Ethernet Controller Block Diagram MDI Interface 1000Base-T PHY Interfaces Design For Test Interface External TBI Interface 10/100/1000 PHY MDIO GMII/ MII Device Funct. #0 MAC/Controller SMB Interface EEPROM Interface Flash Interface LED's S/W Defined Pins PCI (64 bit,33/66MHz); PCI-X (133MHz) 1.1 Document Scope This document contains datasheet specifications for the 82545GM Gigabit Ethernet Controller, which includes signal descriptions, DC and AC parameters, packaging data, and pinout information. 1.2 Reference Documents It is assumed that the designer is acquainted with high-speed design and board layout techniques. Document that may provide additional information are: * * * * * * * 2 PCI Local Bus Specification, Revision 2.3, PCI Special Interest Group. PCI-X Specification, Revision 1.0a, PCI Special Interest Group. PCI Bus Power Management Interface Specification, Rev. 1.1, PCI Special Interest Group. IEEE Standard 802.3, 1996 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3u, 1995 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3x, 1997 Edition, Institute of Electrical and Electronics Engineers (IEEE). IEEE Standard 802.3z, 1998 Edition, Institute of Electrical and Electronics Engineers (IEEE). Datasheet Networking Silicon -- 82545GM * IEEE Standard 802.3ab, 1999 Edition, Institute of Electrical and Electronics Engineers (IEEE). * Intel(R) Ethernet Controllers Timing Device Selection Guide, AP-419. Intel Corporation. 1.3 Product Code The product ordering code for the 82545GM is: RC82545GM. The product ordering code for the lead-free 82545GM is: PC82545GM. Datasheet 3 82545GM -- Networking Silicon Note: 4 This page is intentionally left blank. Datasheet Networking Silicon -- 82545GM 2.0 Additional 82545GM Features 2.1 PCI Features Algorithms that optimally use advanced PCI, MWI, MRM, and MRL commands as well as PCI-X MRD, MRB, and MWB commands 2.2 Benefits * MAC Specific Features Benefits * Network packets handled without waiting or buffer overflow. Mechanism available for reducing interrupts generated by transmit and receive operations * Maximizes system performance and throughput Support for transmission and reception of packets up to 16 Kbytes * Enables jumbo frames Low-latency transmit and receive queues 2.3 PHY Specific Features State-of-the-art DSP architecture implements digital adaptive equalization, echo cancellation, and crosstalk cancellation 2.4 Benefits * Robust performance in noisy environments * Tolerance of common electrical signal impairments Host Offloading Features Descriptor ring management hardware for transmit and receive 16 Kbyte jumbo frame support Interrupt coalescing (multiple packets per interrupt) Datasheet Efficient bus operations Benefits * Optimized fetching and write-back mechanisms for efficient system memory and PCI bandwidth usage * High throughput for large data transfers on networks supporting jumbo frames * Increased throughput by reducing interrupts generated by transmit and receive operations 5 82545GM -- Networking Silicon 2.5 Manageability Features * Enables IPMI and ASF implementations On-board SMB port * Allows packets routing to and from either LAN port and a server management processor Preboot eXecution Environment (PXE) Flash interface support (32-bit nd 64-bit) * Local Flash interface for PXE image * Easy system monitoring with industry standard consoles * Remote network management capabilities through DMI 2.0 and SNMP software * Packet recognition and wake-up for NIC and LOM applications without software configuration SNMP and RMON statistic counters SDG 3.0, WfM 2.0, and PC2001 compliance Wake on LAN support 2.6 Benefits Additional Device Features Benefits Internal PLL for clock generation using a 25 MHz crystal as a clock reference * Lower component count and system cost JTAG (IEEE 1149.1) Test Access Port built in silicon * Simplified testing using boundary scan * Reduced number of on-board power supply regulators * Simplified power supply design * Additional flexibility for LEDs or other low speed I/O devices Supports little endian byte ordering for both 32 and 64 bit systems and big endian byte ordering for 64 bit systems * Portable across application architectures Provides loopback capabilities * Validates silicon integrity * Allows LAN port enabling and disabling through BIOS control (OS not required) On-chip power control circuitry Four software definable pins Single-pin LAN disable function 6 Datasheet Networking Silicon -- 82545GM 2.7 Technology Features Benefits * 21 mm x 21 mm component making LOM designs easier * Single port or dual port implementation on the same board with minor option changes * Offers lowest geometry to minimize power and size while maintaining Intel quality reliability standards * Simple thermal design 3.3 V (5 V tolerant) PCI signaling with power dissipation less than 2.0 W (maximum) * Lower power requirements Improved SERDES differential output * Complies with PICMG 3.1 Specification 364-pin Ball Grid Array (BGA) package Footprint compatible with the 82544GC, 82545EM, and 82546EB controllers Implemented in 0.15 CMOS process 0 C to 70 C (maximum) operating temperature Heat sink or forced airflow not required 65 C to 140 C storage temperature range Datasheet 7 82545GM -- Networking Silicon Note: 8 This page intentionally left blank. Datasheet Networking Silicon -- 82545GM 3.0 Signal Descriptions Note: 3.1 The targeted signal names are subject to change without notice. Verify with your local Intel sales office that you have the latest information before finalizing a design. Signal Type Definitions The signals of the 82545GM controller are electrically defined as follows: Name Definition I Input. Standard input only digital signal. O Output. Standard output only digital signal. TS Tri-state. Bi-directional three-state digital input/output signal. Sustained Tri-state. Sustained digital three-state signal driven by one agent at a time. STS An agent driving the STS pin low must actively drive it high for at least one clock before letting it float. The next agent of the signal cannot drive the pin earlier than one clock after it has been released by the previous agent. Open Drain. Wired-OR with other agents. Note: 3.2 OD The signaling agent asserts the OD signal, but the signal is returned to the inactive state by a weak pull-up resistor. The pull-up resistor may require two or three clock periods to fully restore the signal to the de-asserted state. A Analog. PHY analog data signal. P Power. Power connection, voltage reference, or other reference connection. R Reserved. The TTL inputs on the Ethernet controller are not 5V tolerant. If these inputs are connected to 5V, then damage to the Ethernet controller is likely to occur. TTL inputs include the JTAG interface pins, the FLASH interface pins, the EEPROM interface pins, the LED pins, the software definable pins, and the LAN_PWR_GOOD pin. PCI Bus Interface When the Reset signal (RST#) is asserted, the 82545GM will not drive any PCI output or bidirectional pins except the Power Management Event signal (PME#). Datasheet 9 82545GM -- Networking Silicon 3.2.1 PCI Address, Data and Control Signals Symbol Type Name and Function Address and Data. Address and data signals are multiplexed on the same PCI pins. A bus transaction includes an address phase followed by one or more data phases. AD[63:0] TS The address phase is the clock cycle when the Frame signal (FRAME#) is asserted low. During the address phase AD[63:0] contain a physical address (64 bits). For I/O, this is a byte address, and for configuration and memory, a DWORD address. The 82545GM device uses little endian byte ordering. During data phases, AD[7:0] contain the least significant byte (LSB) and AD[63:56] contain the most significant byte (MSB). The 82545GM controller may optionally be connected to a 32-bit PCI bus. On the 32-bit bus, AD[63:32] and other signals corresponding to the high order byte lanes do not participate in the bus cycle. CBE[7:0]# TS Bus Command and Byte Enables. Bus command and byte enable signals are multiplexed on the same PCI pins. During the address phase of a transaction, CBE[7:0]# define the bus command. In the data phase, CBE[7:0]# are used as byte enables. The byte enables are valid for the entire data phase and determine which byte lanes contain meaningful data. CBE0# applies to byte 0 (LSB) and CBE7# applies to byte 7 (MSB). PAR TS Parity. The Parity signal is issued to implement even parity across AD[31:0] and CBE[3:0]#. PAR is stable and valid one clock after the address phase. During data phases, PAR is stable and valid one clock after either IRDY# is asserted on a write transaction or TRDY# is asserted after a read transaction. Once PAR is valid, it remains valid until one clock after the completion of the current data phase. When the 82545GM controller is a bus master, it drives PAR for address and write data phases, and as a slave device, drives PAR for read data phases. PAR64 TS Parity 64. The Parity 64 signal is issued to implement even parity across AD[63:32] and CBE[7:4]#. PAR64 is stable and valid one clock after the address phase. During data phases, PAR64 is stable and valid one clock after either IRDY# is asserted on a write transaction or TRDY# is asserted after a read transaction. Once PAR64 is valid, it remains valid until one clock after the completion of the current data phase. When the 82545GM controller is a bus master, it drives PAR64 for address and write data phases, and as a slave device, drives PAR64 for read data phases. FRAME# IRDY# TRDY# 10 STS STS STS Cycle Frame. The Frame signal is driven by the 82545GM device to indicate the beginning and length of an access and indicate the beginning of a bus transaction. While FRAME# is asserted, data transfers continue. FRAME# is de-asserted when the transaction is in the final data phase. Initiator Ready. Initiator Ready indicates the ability of the 82545GM controller (as bus master device) to complete the current data phase of the transaction. IRDY# is used in conjunction with the Target Ready signal (TRDY#). The data phase is completed on any clock when both IRDY# and TRDY# are asserted. During the write cycle, IRDY# indicates that valid data is present on AD[63:0]. For a read cycle, it indicates the master is ready to accept data. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. The 82545GM controller drives IRDY# when acting as a master and samples it when acting as a slave. Target Ready. The Target Ready signal indicates the ability of the 82545GM controller (as a selected device) to complete the current data phase of the transaction. TRDY# is used in conjunction with the Initiator Ready signal (IRDY#). A data phase is completed on any clock when both TRDY# and IRDY# are sampled asserted. During a read cycle, TRDY# indicates that valid data is present on AD[63:0]. For a write cycle, it indicates the target is ready to accept data. Wait cycles are inserted until both IRDY# and TRDY# are asserted together. The 82545GM device drives TRDY# when acting as a slave and samples it when acting as a master. Datasheet Networking Silicon -- 82545GM Symbol STS Stop. The Stop signal indicates the current target is requesting the master to stop the current transaction. As a slave, the 82545GM controller drives STOP# to request the bus master to stop the transaction. As a master, the 82545GM controller receives STOP# from the slave to stop the current transaction. IDSEL# I Initialization Device Select. The Initialization Device Select signal is used by the 82545GM as a chip select signal during configuration read and write transactions. DEVSEL# STS Device Select. When the Device Select signal is actively driven by the 82545GM, it signals notifies the bus master that it has decoded its address as the target of the current access. As an input, DEVSEL# indicates whether any device on the bus has been selected. Note: An external resistor is required between the voltage reference and the VIO pin. The target resistor value is 100 K Type Name and Function REQ64# TS Request Transfer. The Request Transfer signal is generated by the current initiator indicating its desire to perform a 64-bit transfer. REQ64# has the same timing as the Frame signal. ACK64# TS Acknowledge Transfer. The Acknowledge Transfer signal is generated by the currently addressed target in response to the REQ64# assertion by the initiator. ACK64# has the same timing as the Device Select signal. REQ# TS Request Bus. The Request Bus signal is used to request control of the bus from the arbiter. This signal is point-to-point. GNT# I Grant Bus. The Grant Bus signal notifies the 82545GM that bus access has been granted. This is a point-to-point signal. LOCK# I Lock Bus. The Lock Bus signal is asserted by an initiator to require sole access to a target memory device during two or more separate transfers. The 82545GM device does not implement bus locking. Interrupt Signal Symbol INTA# Datasheet P VIO. The VIO signal is a voltage reference for the PCI interface (3.3 V or 5 V PCI signaling environment). It is used as the clamping voltage. Arbitration Signals Symbol 3.2.3 Name and Function STOP# VIO 3.2.2 Type Type TS Name and Function Interrupt A. Interrupt A is used to request an interrupt of the 82545GM. It is an active low, level-triggered interrupt signal. 11 82545GM -- Networking Silicon 3.2.4 System Signals Symbol Type Name and Function CLK I PCI Clock. The PCI Clock signal provides timing for all transactions on the PCI bus and is an input to the 82545GM device. All other PCI signals, except the Interrupt A (INTA#) and PCI Reset signal (RST#), are sampled on the rising edge of CLK. All other timing parameters are defined with respect to this edge. M66EN I 66 MHz Enable. The 66 MHz Enable signal is used to indicate whether or not the system bus is capable of supporting an operating frequency of 66 MHz. RST# I PCI Reset. When the PCI Reset signal is asserted, all PCI output signals, except the Power Management Event signal (PME#), are floated and all input signals are ignored. The PME# context is preserved, depending on power management settings. Most of the internal state of the 82545GM is reset on the de-assertion (rising edge) of RST#. LAN_ PWR_ GOOD 3.2.5 Power Good (Power-on Reset). The Power Good signal is used to indicate that stable power is available for the 82545GM. When the signal is low, the 82545GM holds itself in reset state and floats all PCI signals. Error Reporting Signals Symbol SERR# PERR# 3.2.6 I Type Name and Function OD System Error. The System Error signal is used by the 82545GM controller to report address parity errors. SERR# is open drain and is actively driven for a single PCI clock when reporting the error. STS Parity Error. The Parity Error signal is used by the 82545GM controller to report data parity errors during all PCI transactions except by a Special Cycle. PERR# is sustained tri-state and must be driven active by the 82545GM controller two data clocks after a data parity error is detected. The minimum duration of PERR# is one clock for each data phase a data parity error is present. Power Management Signals Symbol PME# Type OD Name and Function Power Management Event. The 82545GM device drives this signal low when it receives a wake-up event and either the PME Enable bit in the Power Management Control/Status Register or the Advanced Power Management Enable (APME) bit of the Wake-up Control Register (WUC) is 1b. Auxiliary Power. If the Auxiliary Power signal is high, then auxiliary power is available and the 82545GM device should support the D3cold power state. AUX_PWR 12 I Note that AUX_PWR is not a supply input, but is an indication of whether AUX_PWR is available to the 82545GM and/or subsystem. Setting AUX_PWR to 1b enables advertising D3cold Wake Up support and changes the reset function of PME_En and PME_Status. AUX_PWR is level sensitive, and any changes are immediately reflected in the D3cold Wake Up advertisements and the PME_En and PME_Status behavior on PCI reset. Datasheet Networking Silicon -- 82545GM 3.2.7 Impedance Compensation Signals Symbol ZN_COMP Type I/O Name and Function N Device Impedance Compensation. This signal should be connected to an external precision resistor (to VDD) that is indicative of the PCI/PCI-X trace load. This cell is used to dynamically determine the drive strength required on the N-channel transistors in the PCI/PCI-X I/O cells. The internal pull-up impedance is nominally 120 K with a minimum of 90 K and a maximum of 190 K. ZP_COMP I/O P Device Impedance Compensation. This signal should be connected to an external precision resistor (to VSS) that is indicative of the PCI/PCI-X trace load. This cell is used to dynamically determine the drive strength required on the P-channel transistors in the PCI/PCI-X I/O cells. The internal pull-up impedance is nominally 120 K with a minimum of 90 K and a maximum of 190 K. 3.2.8 SMB Signals Note: A pull-up resistor with a recommended value of 4.7 K should be placed along the SMB. A precise value may be calculated from the SMB specification. Symbol 3.3 Name and Function SMBCLK I/O SMB Clock. The SMB Clock signal is an open drain signal for serial SMB interface. SMBDATA I/O SMB Data. The SMB Data signal is an open drain signal for serial SMB interface. SMBALRT # O SMB Alert. The SMB Alert signal is open drain for serial SMB interface. EEPROM Interface Signals Symbol Datasheet Type Type Name and Function EE_DI O EEPROM Data Input. The EEPROM Data Input pin is used for output to the memory device. EE_DO I EEPROM Data Output. The EEPROM Data Output pin is used for input from the memory device. The EE_DO includes an internal pull-up resistor. EE_CS O EEPROM Chip Select. The EEPROM Chip Select signal is used to enable the device. EE_SK O EEPROM Serial Clock. The EEPROM Shift Clock provides the clock rate for the EEPROM interface, which is approximately 1 MHz. 13 82545GM -- Networking Silicon 3.4 Flash Interface Signals Symbol Type Name and Function FL_ADDR [18:0] O Flash Address Output. The Flash Address Output signals are used for a Flash or Boot ROM device. FL_CS# O Flash Chip Select. The Flash Chip Select signal is used to enable the Flash or Boot ROM device. FL_OE# O Flash Output Enable. The Flash Output Enable signal is used to enable the Flash buffers. FL_WE# O Flash Write Enable Output. The Flash Write ENable Output signals are used for write cycles. FL_DATA [7:1] TS Flash Data I/O. The Flash Data I/O signals are bi-directional and used for Flash data. These signals include internal pull-up devices. FL_DATA[0 ]/LAN_ DISABLE# TS Flash Data I/O / LAN Disable. This pin is an input from the Flash memory. Alternatively, the pin can be used to disable the LAN port from a system General Input Output (GPIO) port. It has an internal pull-up device. If the 82545GM is not using Flash functionality, the pin should be connected to external pull-up resistor. If this pin is used as LAN_DISABLE, the device transitions to a low power state, and the LAN port is disabled when this pin is sampled low on the rising edge of PCI reset. 3.5 Miscellaneous Signals 3.5.1 LED Signals Symbol 3.5.2 Type Name and Function Activity. The Activity LED signal flashes an LED to indicate receive activity on the Ethernet port for packets only destined to this node. ACT# O LINK# O Link. The Link LED signal indicates link connectivity on the Ethernet port. LINK100# O Link 100. The Link 100 signal drives an LED indicating link at 100 Mbps on the Ethernet port. LINK1000# O Link 1000. The Link 1000 signal drives an LED indicating link at 1000 Mbps on the Ethernet port. Software Definable Signals Symbol SDP[7:6] SDP[1:0] Type TS Name and Function Software Defined Pin. The Software Defined Pins are reserved and programmable with respect to input and output capability. These default to input signals upon powerup but may be configured differently by the EEPROM. The upper four bits may be mapped to the General Purpose Interrupt bits if they are configured as input signals. Note: SDP5 is not included in the group of Software Defined Pins. 14 Datasheet Networking Silicon -- 82545GM 3.6 PHY Signals 3.6.1 Crystal Signals Symbol 3.6.2 Type Name and Function XTAL1 I Crystal One. The Crystal One pin is a 25 MHz +/- 30 ppm input signal. It can be connected to a 25 MHz crystal. Crystal Two (XTAL2) must also be connected. XTAL2 O Crystal Two. Crystal Two is the output of an internal oscillator circuit used to drive a crystal into oscillation. If an external oscillator is used in the design, XTAL2 must be disconnected. Analog Signals Symbol REF Type P Name and Function Reference. This Reference signal should be connected to VSS through an external 2.49 K resistor. Media Dependent Interface [0]. 1000BASE-T: In MDI configuration, MDI[0]+/- corresponds to BI_DA+/-, and in MDI-X configuration, MDI[0]+/- corresponds to BI_DB+/-. MDI[0]+/- A 100BASE-TX: In MDI configuration, MDI[0]+/- is used for the transmit pair, and in MDI-X configuration, MDI[0]+/- is used for the receive pair. 10BASE-T: In MDI configuration, MDI[0]+/- is used for the transmit pair, and in MDI-X configuration, MDI[0]+/- is used for the receive pair. Media Dependent Interface [1]. 1000BASE-T: In MDI configuration, MDI[1]+/- corresponds to BI_DB+/-, and in MDI-X configuration, MDI[1]+/- corresponds to BI_DA+/-. MDI[1]+/- A 100BASE-T: In MDI configuration, MDI[1]+/- is used for the receive pair, and in MDI-X configuration, MDI[1]+/- is used for the transit pair. 10BASE-T: In MDI configuration, MDI[1]+/- is used for the receive pair, and in MDI-X configuration, MDI[1]+/- is used for the transit pair. Media Dependent Interface [2]. 1000BASE-T: In MDI configuration, MDI[2]+/- corresponds to BI_DC+/-, and in MDI-X MDI[2]+/- A configuration, MDI[2]+/- corresponds to BI_DD+/-. 100BASE-TX: Unused. 10BASE-T: Unused. Media Dependent Interface [3]. 1000BASE-T: In MDI configuration, MDI[3]+/- corresponds to BI_DD+/-, and in MDI-X MDI[3]+/- A configuration, MDI[3]+/- corresponds to BI_DC+/-. 100BASE-TX: Unused. 10BASE-T: Unused. Datasheet 15 82545GM -- Networking Silicon 3.7 Serializer / Deserializer (SERDES) Signals Symbol 3.8 Type Name and Function RX +/- I SERDES Receive Pair. These two signals comprise the differential receive pair for the 1.25 GHz serial interface. If the SERDES interface is not used, these signals should not be connected. TX +/- O SERDES Transmit Pair. These two signals comprise the differential transmit pair for the 1.25 GHz serial interface. If the SERDES interface is not used, these signals should not be connected. SIG_ DETECT I Signal Detect. This pin indicates when a SERDES signal (connected to the 1.25 GHz serial interface) has been detected by the optical transceiver. If the SERDES interface is not used, this signal should be connected to ground through a pull-down resistor. JTAG Test Interface Signals Symbol Type Name and Function JTAG_TCK I JTAG Clock. JTAG_TDI I JTAG TDI. JTAG_TDO O JTAG TDO. JTAG_TMS I JTAG TMS. JTAG_ TRST# I JTAG Reset. This is an active low reset signal for JTAG. This signal should be terminated using a pull-down resistor to ground. It must not be left unconnected. CLK_VIEW O Clock View. The Clock View signal is an output for the clock signals required for IEEE testing. The clock is selected by register programming. For IEEE testing, a 2-pin header should be connected to CLK_VIEW with one signal connected to GND, and the other, to CLK_VIEW. TEST# I Factory Test Pin. This is an active low input and has an internal pull-up resistor. For normal operation, TEST# should be left unconnected. 3.9 Power Supply Connections 3.9.1 Power Support Signals Symbol 16 Type Name and Function CTRL_15 A 1.5 V Control. The 1.5 V Control signal is an output to an external power transistor. If regulators are used, it should be left unconnected. CTRL_25 A 2.5 V Control. The 2.5 V Control signal is an output to an external power transistor. If regulators are used, it should be left unconnected. Datasheet Networking Silicon -- 82545GM 3.9.2 Digital Supplies Symbol 3.9.3 P 3.3 V I/O Power Supply. DVDD P 1.5 V Digital Core Power Supply. Analog Supplies Type Name and Function AVDDH P 3.3 V Analog Power Supply. AVDDL P 2.5 V Analog Power Supply. Ground and No Connects Symbol Datasheet Name and Function VDDO Symbol 3.9.4 Type Type Name and Function GND P Ground. NC P No Connect. Do not connect any circuitry to these pins. Pull-up or pull-down resistors should not be connected to these pins. Reserved R Reserved. These pins are reserved for factory purposes and should be pulled down to ground through a pull-down resistor. 17 82545GM -- Networking Silicon Note: 18 This page is intentionally left blank. Datasheet Networking Silicon -- 82545GM 4.0 Test Port Functionality 4.1 XOR Testing A common board or system-level manufacturing test for proper electrical continuity between a silicon component and the board is some type of cascaded-XOR or NAND tree test. The 82545GM implements an XOR tree spanning most I/O signals. The component XOR tree consists of a series of cascaded XOR logic gates, each stage feeding in the electrical value from a unique pin. The output of the final stage of the tree is visible on an output pin from the component. Figure 2. XOR Tree Concept By connecting to a set of test-points or bed-of-nails fixture, a manufacturing test fixture can test connectivity to each of the component pins included in the tree by sequentially testing each pin, testing each pin when driven both high and low, and observing the output of the tree for the expected signal value and/or change. 4.1.1 XOR Tree Control and Operation The following signals are required to place the 82545GM in XOR tree test mode: Test Function/ Mode Pin Name TEST_DM_N Dual-Mode Name XOR Tree Test Datasheet 0 EWRAP CLK_BYP_N CLK_VIEW SDP_B[7] TEST_ MODE[3] TEST_ MODE[2] TEST_ MODE[1] TEST_ MODE[0] 0 0 0 0 19 82545GM -- Networking Silicon I/O pins with dual-mode function for XOR test: Pin Name FLSH_CE_N Dual-Mode Name XOR_OUT Pin Function Output of XOR tree. When XOR tree test is selected, the following pin behavior(s) occur: * Output drivers for the pins listed as tested are all placed in high-impedance (tri-state) state to ensure that the board/system test fixture can drive the tested inputs without contention * The output driver for the XOR tree output on pin FLSH_CE_N is explicitly enabled. 4.1.2 Pins Tested When performing XOR test, those pins tested by the XOR tree all function as inputs, regardless of the normal directionality of the pin. The following table(s) cites the pins tested and not-testable as inputs to the XOR tree. Table entries do not reflect the natural order of input into the XOR tree itself (nor need to, as the output of a multi-input XOR function is order-independent). Pins included in XOR test tree are listed in Table 1: Table 1. Tested Pins Included in XOR Tree Pin Name PCI_AD[63:0] 20 Pin Name M66EN Pin Name RX_DATA[7:0] PCI_CBE_N[7:0] PCI_RST_N RBC0/RX_CLK PCI_PAR LAN_PWR_GOOD RBC1/MTX_CLK PCI_PAR64 PCI_SERR_N EE_DI PCI_FRAME_N PCI_PERR_N EE_DO PCI_IRDY_N PCI_PME_N EE_CS PCI_TRDY_N AUX_PWR EE_SK PCI_STOP_N SMBCLK FLSH_ADDR[18:0] PCI_IDSEL SMBDAT FLSH_OE_N PCI_DEVSEL_N TX_DATA[9]/TX_ER FLSH_WE_N PCI_REQ64_N TX_DATA[8]/TX_EN FLSH_DATA[7:0] PCI_ACK64_N TX_DATA[7:0] LED_A[3:0] PCI_REQ_N GTX_CLK LED_B[3:0] PCI_GNT_N COL SDP_A[7,6,1,0] PCI_LOCK_N CRS SDP_B[6,1,0] PCI_INTA_N LINK/LOS ALTCLK_125 PCI_INTB_N RX_DATA[9]/RX_ER PCI_CLK RX_DATA[8]/RX_DV Datasheet Networking Silicon -- 82545GM Pins not included in XOR test tree: * JTAG (TAP) interface: TRST_N, TCK, TDO, TMS, and TDO * Test mode decode controls TEST_DM_N, EWRAP, CLK_BYP_N, CLK_VIEW, and SDP_B[7] * * * * * * 4.2 Each internal PHY's analog signals including PHYREF, MDI +/-, and PHY_HSDACP/N PCI Impedance Compensation ZPCOMP and ZNCOMP Oscillator signals XTAL1 and XTAL2 Test signals including PHY_TSTPT and each PHY's HSDACP/N Power-control pins CTRL_15, CTRL_25_A, and CTRL_25_B SMB_ALERT_N/PCI_PWR_GOOD Tristate Mode The 82545GM's tristate test mode is used to explicitly disable output drivers and place outputs in high-impedance (tristate) state. To more readily support XOR or NAND-tree like testing of other system components, the 82545GM decodes this test mode from the same signal pins used to exercise XOR tree testing. The 82545GM additionally supports a mechanism to enter tristate mode via the IEEE 802.3 JTAG (TAP) controller. 4.2.1 Tristate Mode Control and Operation The following signals are required to place the 82545GM in tristate test mode: Test Function/ Mode Pin Name TEST_DM_N Dual-Mode Name Tristate Mode 0 EWRAP CLK_BYP_N CLK_VIEW SDP_B[7] TEST_ MODE[3] TEST_ MODE[2] TEST_ MODE[1] TEST_ MODE[0] 0 1 0 1 When in tristate test mode: * All output drivers for all digital signal pins are disabled (with the exception of the TDO pin). * Analog signals such as MDI+/-, analog test points, and regulator controls are unaffected. 4.2.2 Tristate Mode Using JTAG (TAP) The 82545GM can also be placed in tristate mode using the JTAG interface and the HIGHZ instruction. The HIGHZ instruction is used to place the 82545GM in high-impedance (TRISTATE) mode, where all digital signal outputs are placed in high-impedance (tri-state) output state. Datasheet 21 82545GM -- Networking Silicon Note: 22 This page intentionally left blank. Datasheet Networking Silicon -- 82545GM 5.0 Voltage, Temperature, and Timing Specifications Note: 5.1 Table 2. The specification values listed in this section are subject to change without notice. Verify with your local Intel sales office that you have the latest information before finalizing a design. Targeted Absolute Maximum Ratings Absolute Maximum Ratingsa Symbol Parameter Min Max Unit VDD (3.3) DC supply voltage on VDDD or AVDDH with respect to VSS VSS - 0.5 4.6 V VDD (2.5) DC supply voltage on AVDDL with respect to VSS VSS - 0.5 4.6 or VDD (2.5) + 0.5b V VDD (1.5) DC supply voltage on DVDD with respect to VSS VSS - 0.5 4.6 or VDD (1.5) + 0.5c V VDD DC supply voltage VSS - 0.5 4.6 V VI / VO LVTTL input voltage VSS - 0.5 4.6 V 5 V compatible input voltage VSS - 0.5 6.6 V VI / VO DC output current (by cell type): IO TSTG IOL = 3 mA 10 IOL = 6 mA 20 IOL - 12 mA 40 Storage temperature range -40 ESD per MIL_STD-883 Test Method 3015, Specification 2001V Latchup Over/Undershoot: 150 mA, 125 C mA 125 C VDD overstress: VDD(3.3)(7.2 V) V a. Maximum ratings are referenced to ground (VSS). Permanent device damage is likely to occur if the ratings in this table are exceeded. These values should not be used as the limits for normal device operations. b. The maximum value is the lesser value of 4.6 V or VDD(2.5) + 0.5 V. This specification applies to biasing the device to a steady state for an indefinite duration. During normal device power-up, explicit power sequencing is not required. c. The maximum value is the lesser value of 4.6 V or VDD(2.5) + 0.5 V. 5.2 Table 3. Recommended Operating Conditions Recommended Operating Conditionsa Symbol Datasheet Parameter Min Max Unit VDD (3.3) DC supply voltage on VDDD or AVDDHb 3.0 3.6 V VDD (2.5) DC supply voltage on AVDDLc 2.38 2.62 V VDD (1.5) DC supply voltage on DVDD 1.43 1.57 V VIO PCI bus voltage reference 3.0 5.25 V 23 82545GM -- Networking Silicon Table 3. Recommended Operating Conditionsa Symbol Parameter Min Max Unit tR / tF Input rise/fall time (normal input) 0 200 ns tr/tf input rise/fall time (Schmitt input) 0 10 ms TA Operating temperature range (ambient) 0 70 C TJ Junction temperature 125 C a. Sustained operation of the device at conditions exceeding these values, even if they are within the absolute maximum rating limits, might result in permanent damage. b. It is recommended for VDDO to equal AVDDH (VDDO = AVDDH) during power-up and normal operation. c. It is recommended for both VDDO and AVDDH to be of a value greater than AVDDL, with a value greater than DVDD, during power-up (VDDO or AVDDH > AVDDL > DVDD). 5.3 Table 4. DC Specifications DC Characteristics Symbol Parameter Min Typ Max Units VDD (3.3) DC supply voltage on VDDO or AVDDH 3.00 3.3 3.60 V VDD (2.5) DC supply voltage on AVDDL 2.38 2.5 2.62 V VDD (1.5) DC supply voltage on DVDD 1.43 1.5 1.57 V Table 5.a Power Supply Characteristics D0a Unplugged/No Link 10 Mbps Operation 100 Mbps Operation Typa Icc (mA) Maxb Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 45 50 65 70 65 70 135 155 2.5 V 25 30 40 50 70 75 165 175 1.5 V 85 95 90 105 120 130 400 425 1.45 W 1.7 W Total Device Power 350 mW 450 mW 575 mW 1000 Mbps Operation a. Typical conditions: operating temperature (TA) = 25 C, nominal voltages, moderate network traffic at full duplex, and PCI 66 MHz system interface. b. Maximum conditions: minimum operating temperature (TA) values, maximum voltage values, and PCI-X 100 to 133 MHZ system interface. 24 Datasheet Networking Silicon -- 82545GM Table 5.b D3cold - Wake Up Enabled D3cold - Wake Up Disabled Unplugged/No Link 10 Mbps Operation 100 Mbps Operation Typa Icc (mA) Maxb Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 40 45 55 60 50 55 40 45 2.5 V 30 30 30 30 60 65 30 30 1.5 V 30 35 30 35 55 60 10 10 Total Device Power 250 mW 300 mW 400 mW 225 mW a. Typical conditions: operating temperature (TA) = 25 C, nominal voltages, moderate network traffic at full duplex, and PCI 66 MHz system interface. b. Maximum conditions: minimum operating temperature (TA) values, maximum voltage values, and PCI-X 100 to 133 MHZ system interface. Table 5.c Uninitialized/Disabled D(n) Uninitialized (LAN PWR GOOD = 0) Disabled (via Flash Address) Typa Icc (mA) Maxb Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 40 45 40 45 2.5 V 40 45 25 30 1.5 V 190 200 10 15 Total Device Power 520 mW 210 mW a. Typical conditions: operating temperature (TA) = 25 C, nominal voltages, moderate network traffic at full duplex, and PCI 66 MHz system interface. b. Maximum conditions: minimum operating temperature (TA) values, maximum voltage values, and PCI-X 100 to 133 MHZ system interface. Datasheet 25 82545GM -- Networking Silicon Table 5.d Complete Subsystem (including magnetics, LED, and regulator circuits) D3cold / Wake disabled D3cold / Wake Enabled at 10 Mbps D3cold / Wake Enabled at 100 Mbps D0 at 1000 Mbps Typa Icc Maxb Icc Typ Icc Max Icc Typ Icc Max Icc Typ Icc Max Icc (mA) (mA) (mA) (mA) (mA) (mA) (mA) (mA) 3.3 V 40 45 60 65 60 65 140 160 2.5 V 30 30 40 40 85 90 260 270 1.5 V 10 10 30 35 55 60 400 425 Subsystem 3.3 V Current 85 mA 140 mA 215 mA 855 mA a. Typical conditions: operating temperature (TA) = 25 C, nominal voltages, moderate network traffic at full duplex, and PCI 66 MHz system interface. b. Maximum conditions: minimum operating temperature (TA) values, maximum voltage values, and PCI-X 100 to 133 MHZ system interface. NOTE: Component power has been specified separately from subsystem power to aid in calculating thermal operation and in providing external power supply circuits. Complete subsystem power is specified to aid in providing overall power supply design for the applications. Table 6.a MAC/SERDES Characteristics Component Only D0a (SERDES Active) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 65 75 45 50 2.5 V 60 70 leakage leakage 1.5 V 115 130 5 5 540 mW 660 mW 150 mW 200 mW Total Device Power 26 D3cold - Wake Disabled (SERDES Off) Datasheet Networking Silicon -- 82545GM Table 6.b Complete Subsystem (Reference SERDES Design) Including LED, Regulator Circuits (no optics) D3cold Wake Disabled (Auxiliary Power) D0 SERDES Active (Primary Power) Typ Icc (mA) Max Icc (mA) Typ Icc (mA) Max Icc (mA) 3.3 V 45 50 70 80 2.5 V -0 -0 60 70 1.5 V 5 5 115 130 Subsystem 3.3 V Current 55 mA 280 mA NOTE: In fiber/optical application or SERDES driven backplane application, power is substantially less than when operating with a PHY/magnetics. For calculating thermal operations and in providing external power-supply circuits for such applications, SERDES mode power is provided separately. Power is specified into a load of 50 pF at default SERDES amplitude setting. Power consumed by optics module (if present) is not included. NOTE: Power specifications for uninitialized/disabled state are detailed under the copper MAC/PHY specifications. Table 7. I/O Characteristics Symbol Parameter Condition Min Typ Max Unit VIL Voltage input LOW -0.5 0.8 V VIH Voltage input HIGH 2.0 VDD +0.3 V VOL Voltage output LOW 0.4 V VOH Voltage output HIGH 2.4 V VSH Schmitt Trigger Hysteresis 0.1 V Output current LOW IOLa 3mA drivers (TTL3) VOL 3 mA 6mA drivers (TTL6) VOL 6 mA 12mA drivers (TTL12) VOL 12 mA 3mA drivers (TTL3) VOH -3 mA 6mA drivers (TTL6) VOH -6 mA 12mA drivers (TTL12) VOH -12 mA Output current HIGH IOHa Input Current IIN IOZ Datasheet TTL inputs VIN = VDD or VSS -10 Inputs with pull-down resistors VIN = VDD 150 TTL inputs with pull-up resistors VIN = VSS -150 3-state output leakage current VOH = VDD or VSS -10 1 1 10 A 480 A -480 A 10 A 27 82545GM -- Networking Silicon Table 7. I/O Characteristics Symbol Parameter Condition CIN Input capacitance Any input and bidirectional buffer COUT Output capacitance Any output buffer CPUD Pull-up/down Resistor value Min Typ Max 2.5 pF 2.0 7.5 Unit pF 20 k a. TTL3 signals include: EE_DI, EE_SK, EE_CS, and JTAG_TDO. TTL6 signals include: FL_CE#, CLK_VIEW, FL_DATA[7:0], FL_ADDR[18:0], FL_OE#, and FL_WE#. TTL12 signals include: LED0 / LINK #, LED1 / ACT #, LED2 / LINK100 #, LED3 / LINK1000 #, SDP0, SDP1, SDP6, and SDP7. 5.4 Table 8. AC Characteristics AC Characteristics: 3.3 V Interfacing Symbol Table 9. Parameter fPCICLK Clock frequency in PCI mode fPCICLK Clock frequency in PCI-X mode Min Typ 66 Max Unit 66 MHz 133 MHz 25 MHz Clock Input Requirements Symbol fi_TX_CLK Parametera TX_CLK_IN frequency Min Typ Max Unit 25 - 50 ppm 25 25 + 50 ppm MHz a. This parameter applies to an oscillator connected to the Crystal One (XTAL1) input. Alternatively, a crystal may be connected to XTAL1 and XTAL2 as the frequency source for the internal oscillator. 28 Datasheet Networking Silicon -- 82545GM Table 10. Link Interface Clock Requirements Symbol fGTX a Parameter Min Typ GTX_CLK frequency Max 125 Unit MHz a. GTX_CLK is used externally for test purposes only. Table 11. EEPROM Interface Clock Requirements Symbol Parameter Min Typ fSK Max Unit 1 MHz Table 12. AC Test Loads for General Output Pins Symbol Signal Name Value Units CL TDO 10 pF CL APM_WAKEUP, PME#, SDP[7:6], SDP[1:0] 16 pF CL EE_DI, EE_SK, FL_ADDR[18:0], FL_CS#, FL_OE#, FL_WE#, FL_DATA[7:0] 18 pF CL RX_ACTIVITY, TX_ACTIVITY, LINK_UP 20 pF Figure 3. AC Test Loads for General Output Pins CL 5.5 Serial Interface Specifications Table 13. Driver Characteristics Symbol Datasheet Parameter Min VOD Differential Output Voltage Swinga VOS Output Offset Voltage Delta VOD Change in VOD between 0 and 1b Typ Max Units 875 1325 mV peakpeak 1075 1325 mV 25 mV 29 82545GM -- Networking Silicon Table 13. Driver Characteristics Symbol Parameter Min Typ Max Units 120 RO Differential Output Impedance ISA, ISB Output Current on Short to VSS 40 mA ISAB Output Current when A and B are Shorted 12 mA 80 a. This is the maximum inside dimension of the eye pattern, measured on high and low data patterns with pre-emphasis present. Load - 100 . b. This is defined as an absolute value of amplitude jitter. Table 14. Receiver Characteristics Symbol 5.6 Parameter Min Typ Max Units VID Differential Input Voltage Swing 100 2000 mV peakpeak RIN Differential Input Impedance 80 120 Timing Specifications Note: Timing specifications are preliminary and subject to change. Verify with your local Intel sales office that you have the latest information before finalizing a design. 5.6.1 PCI/PCI-X Bus Interface 5.6.1.1 PCI/PCI-X Bus Interface Clock Table 15. PCI/PCI-X Bus Interface Clock Parameters Symbol TCYC Parametera CLK cycle time PCI-X 133 MHz PCI-X 66 MHz PCI 66MHz PCI 33 MHz Units Min Max Min Max Min Max Min 7.5 20 15 20 15 30 30 Max ns TH CLK high time 3 6 6 11 ns TL CLK low time 3 6 6 11 ns CLK slew rate 1.5 b RST# slew rate 50 4 1.5 50 4 1.5 50 4 1 50 4 V/ns mV/ns a. Rise and fall times are specified in terms of the edge rate measured in V/ns. This slew rate must be met across the minimum peak-to-peak portion of the clock waveform as shown. b. The minimum RST# slew rate applies only to the rising (de-assertion) edge of the reset signal and ensures that system noise cannot render a monotonic signal to appear bouncing in the switching range. 30 Datasheet Networking Silicon -- 82545GM Figure 4. PCI/PCI-X Clock Timing Tcyc Th 0.6 Vcc 3.3 V Clock 0.5 Vcc 0.4 Vcc p-to-p (minimum) 0.4 Vcc 0.3 Vcc 0.2 Vcc Tl 5.6.1.2 PCI/PCI-X Bus Interface Timing Table 16. PCI/PCI-X Bus Interface Timing Parameters Symbol Parameter PCI-X 133 MHz PCI-X 66 MHz PCI 66MHz PCI 33 MHz Units Min Max Min Max Min Max Min Max TVAL CLK to signal valid delay: bussed signals 0.7 3.8 0.7 3.8 2 6 2 11 ns TVAL (ptp) CLK to signal valid delay: point-to-point signals 0.7 3.8 0.7 3.8 2 6 2 12 ns TON Float to active delay TOFF Active to float delay TSU Input setup time to CLK: bussed signals 1.2 1.7 3 7 ns TSU (ptp) Input setup time to CLK: point-to-point signals 1.2 1.7 5 10, 12 ns TH Input hold time from CLK 0.5 0.5 0 0 ns TRRSU REQ64# to RST# setup time TRRH RST# to REQ64# hold time 0 0 7 2 7 2 14 ns 28 10* 10* 10* 10* TCYC TCYC TCYC TCYC 0 0 0 0 ns ns ns NOTES: 1. Output timing measurements are as shown. 2. REQ# and GNT# signals are point-to-point and have different output valid delay and input setup times than bussed signals. GNT# has a setup of 10 ns; REQ# has a setup of 12 ns. All other signals are bussed. 3. Input timing measurements are as shown. Datasheet 31 82545GM -- Networking Silicon Figure 5. PCI Bus Interface Output Timing Measurement VTH PCI_CLK VTEST VTL Output Delay VTEST VSTEP (3.3V Signalling) output current leakage current Tri-State Output TON TOFF Figure 6. PCI Bus Interface Input Timing Measurement Conditions VTH PCI_CLK VTEST VTL TSU TH VTH Input VTEST Input Valid VTEST VMAX VTL Table 13. PCI Bus Interface Timing Measurement Conditions Symbol Parameter PCI 66 MHz 3.3 v Unit VTH Input measurement test voltage (high) 0.6*VCC 0.6*VCC V VTL Input measurement test voltage (low) 0.25*VCC 0.2*VCC V VTEST Output measurement test voltage 0.4*VCC 0.4*VCC V 1.5 1.5 V/ns Input signal slew rate 32 PCI-X Datasheet Networking Silicon -- 82545GM Figure 7. TVAL (max) Rising Edge Test Load Pin Test Point 1/2 inch max. 25 10 pF Figure 8. TVAL (max) Falling Edge Test Load Pin Test Point 1/2 inch max. 25 10 pF 5.6.2 Link Interface Timing 5.6.2.1 Link Interface Rise and Fall Time VCC Table 17. Rise and Fall Times Symbol Datasheet Parameter Condition Min Max Unit TR Clock rise time 0.8 V to 2.0 V 0.7 ns TF Clock fall time 2.0 V to 0.8 V 0.7 ns TR Data rise time 0.8 to 2.0 V 0.7 ns TF Data fall time 2.0 V to 0.8 V 0.7 ns 33 82545GM -- Networking Silicon Figure 9. Link Interface Rise/Fall Timing 2.0 V 0.8 V TR 5.6.2.2 TF Link Interface Transmit Timing Figure 10. Transmit Interface Timing 1.4V TX_CLOCK TSU TX_DATA[9:0] TH Valid Data TPERIOD Table 18. Transmit Interface Timing Symbol Parameter Min Typ Max Unit a TPERIOD GTX_CLK period TBI mode (1000 Mbps) TSETUP Data setup to rising GTX_CLK THOLD Data hold from rising GRX_CLK TDUTY GTX_CLK duty cycle 8 ns 2.5 ns 1.0 40 ns 60 % a. GTX_CLK should have a 100 ppm tolerance. 34 Datasheet Networking Silicon -- 82545GM 5.6.2.3 Link Interface Receive Timing Figure 11. Receive Interface Timing 1.4V RBC1 TSU TH 2.0V COMMA Code_Group RX_DATA[9:0] Valid Data 0.8V 2.0V COM_DET 0.8V TA-B TSU TH 1.4V RBC0 Table 19. Transmit Interface Timing Symbol Min Typ Max Unit RBC0/RBC1 frequency TBI mode (1000 Mbps) 62.5 TSETUP Data setup before rising RBC0/RBC1 2.5 ns THOLD Data hold after rising RBC0/RBC1 1 ns TDUTY RBC0/RBC1 duty cycle 40 60 % TA-B RBC0/RBC1 skew 7.5 8.5 ns TREQ Datasheet Parameter MHz 35 82545GM -- Networking Silicon 5.6.3 Flash Interface Figure 12. Flash Read Timing 0ns 250ns Flash CE# Flash OE# Flash WE# Flash Address [18:0] Flash Data Table 20. Flash Read Operation Timing Symbol TCE Parameter Min Typ Flash CE# or OE# to read data delay TACC Flash address setup time THOLD Data hold time 0 Max Unit 160 ns 160 ns ns Figure 13. Flash Write Timing 0ns 250ns 500ns Flash CE# Flash OE# Flash WE# Flash Address [18:0] Flash Data 36 Datasheet Networking Silicon -- 82545GM Table 21. Flash Write Operation Timing Symbol 5.6.4 Parameter TWE Flash write pulse width (WE#) TAH Flash address hold time TDS Flash data setup time Min Typ Max 160 Unit ns 0 ns 160 ns EEPROM Interface Table 22. Link Interface Clock Requirements Symbol TPW Parameter Min EE_SK pulse width Typ Max TPERIOD*128 Unit ns Table 23. Link Interface Clock Requirements Symbol Parametera Min Typ Max Unit TDOS EE_DO setup time TCYC*2 ns TDOH EE_DO hold time 0 ns a. The EE_DO setup and hold time is a function of the CLK cycle time but is referenced to O_EE_SK. Datasheet 37 82545GM -- Networking Silicon Note: 38 This page left intentionally blank. Datasheet Networking Silicon -- 82545GM 6.0 Package and Pinout Information 6.1 Device Identification Figure 14. 82545GM Device Identification Markings (R) RC82545GM S Unnn Intel'ZZ YYWW Fnnnnnnnn Country RC82545GM Product Name YYWW Date Code Fnnnnnnnn Lot Trace Code (c)'ZZ Copyright Information Country Country of Origin Assembly NOTE: The dot in the lower left corner indicates the location of pin 1. Datasheet 39 82545GM -- Networking Silicon 6.2 Lead-Free Device Identification Figure 15. Lead-Free 82545GM Device Identification Markings intel R PC82545GM YYWW Xnnnnnnnn Q542 SAMPLE C `03 e1 TAIWAN Pin 1 Indicator 40 PC82545GM Product Name YYWW Date Code Xnnnnnnnn Lot Trace Code (c)'03 (e1) Copyright Information and LeadFree Mark Taiwan Country of Origin Assembly Datasheet Networking Silicon -- 82545GM 6.3 Package Information The 82545GM device is a 364-lead ball grid array (BGA) measuring 21 mm2. The package dimensions are detailed in the figures below. The nominal ball pitch is 1 mm. Figure 16. 82545GM 364-Lead BGA Ball Pad Dimensions Detail Area 0.40 +/- 0.05 mm Solder Mask Opening 0.55 +/- 0.05 mm Pad Size Datasheet 41 Y W V U T R P N M L K J H G F E D C B A -C- 1 PIN 1 CORNER 0.25 C 42 (0.36) 2 3 4 5 7 8 9 SEATING PLANE 6 10 11 12 13 14 TOP VIEW 15 16 17 18 19 20 21.000.10 -B- 19.00 -A- 1.00 0.20(4X) 20 19 18 17 16 15 14 13 11 10 21.000.10 12 BOTTOM VIEW 9 8 7 1.00 6 5 4 3 2 1 Y W V U T R P N M L K J H G F E D C B A PIN 1 CORNER 82545GM -- Networking Silicon Figure 17. 82545GM Mechanical Specifications Datasheet 1.70 MAX 0.20 0.30~0.50 Networking Silicon -- 82545GM 6.4 Thermal Specifications The 82545GM device is specified for operation when the ambient temperature (TA) is within the range of 0 C (minimum ambient temperature) to 70 C (maximum ambient temperature). The maximum junction temperature for the device is 120 C. TC (case temperature) is calculated using the equation: TC = TA + P (JA - JC) TJ (junction temperature) is calculated using the equation: TJ = TA + P JA P (power consumption) is calculated by using the typical ICC and nominal VCC. The thermal resistances are shown in Table 24. Table 24. Thermal Characteristics Value at specified airflow (m/s) Symbol Parameter Units 0 1 2 JA Thermal resistance, junction-to-ambient 19.2 17.1 15.4 C/Watt JC Thermal resistance, junction-to-case 4.6 4.6 4.6 C/Watt Thermal resistances are determined empirically with test devices mounted on standard thermal test boards. Real system designs may have different characteristics due to board thickness, arrangement of ground planes, and proximity of other components. The case temperature measurements should be used to assure that the 82545GM device is operating under recommended conditions. Datasheet 43 82545GM -- Networking Silicon 6.5 Ball Mapping Diagram Note: The 82545GM device uses five categories of VDD connections: VDDO (3.3 V), AVDDH (Analog 3.3 V), AVDDL (Analog 2.5 V), and DVDD (1.5 V). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A B C D E F G H J K L M N P R T U V W Y 6.6 Pinout Information Table 25. PCI Address, Data, and Control Signals Signal 44 Pin Signal Pin Signal Pin PCI_AD[0] T14 PCI_AD[28] Y3 PCI_AD[56} T17 PCI_AD[1] V14 PCI_AD[29] U4 PCI_AD[57] U18 PCI_AD[2] Y15 PCI_AD[30] V3 PCI_AD[58] V18 Datasheet Networking Silicon -- 82545GM Table 25. PCI Address, Data, and Control Signals Signal Pin Signal Pin Signal Pin PCI_AD[3] W14 PCI_AD[31] V1 PCI_AD[59] U16 PCI_AD[4] T13 PCI_AD[32] L16 PCI_AD[60] V17 PCI_AD[5] V13 PCI_AD[33] M20 PCI_AD[61] W18 PCI_AD[6] Y14 PCI_AD[34] M19 PCI_AD[62] Y19 PCI_AD[7] U12 PCI_AD[35] M16 PCI_AD[63] T16 PCI_AD[8] V12 PCI_AD[36] M18 CBE[0]# Y13 PCI_AD[9] T12 PCI_AD[37] M17 CBE[1]# V10 PCI_AD[10] W12 PCI_AD[38] N20 CBE[2]# T8 PCI_AD[11] Y12 PCI_AD[39] N16 CBE[3]# Y4 PCI_AD[12] V11 PCI_AD[40] P20 CBE[4]# V16 PCI_AD[13] T11 PCI_AD[41] N18 CBE[5]# Y18 PCI_AD[14] Y11 PCI_AD[42] P19 CBE[6]# Y17 PCI_AD[15] W10 PCI_AD[43] P16 CBE[7]# T15 PCI_AD[16] U8 PCI_AD[44] R20 PAR U10 PCI_AD[17] Y7 PCI_AD[45] P18 PAR64 V15 PCI_AD[18] Y6 PCI_AD[46] P17 FRAME# V8 PCI_AD[19] V7 PCI_AD[47] T20 IRDY# W8 PCI_AD[20] T7 PCI_AD[48] R16 TRDY# Y8 PCI_AD[21] W6 PCI_AD[49] U20 STOP# V9 PCI_AD[22] Y5 PCI_AD[50] R18 IDSEL T6 PCI_AD[23] V6 PCI_AD[51] T19 DEVSEL# T9 PCI_AD[24] U6 PCI_AD[52] V20 VIO Y1 PCI_AD[25] V5 PCI_AD[53] T18 VIO Y20 PCI_AD[26] W4 PCI_AD[54] W20 PCI_AD[27] V4 PCI_AD[55] V19 Table 26. PCI Arbitration Signals Signal Pin Signal Pin REQ64# U14 REQ# W2 ACK64# W16 GNT# T3 Signal LOCK# Pin Y9 Table 27. Interrupt Signals Signal INTA# Datasheet Pin Signal Pin Signal Pin Y2 45 82545GM -- Networking Silicon Table 28. System Signals Signal CLK Pin U2 Signal M66EN Pin Y16 Signal RST# Pin T5 Table 29. Error Reporting Signals Signal SERR# Pin T10 Signal PERR# Pin Signal Pin Signal Pin Y10 Table 30. Power Management Signals Signal Pin LAN_PWR_ GOOD A17 Signal PME# Pin T4 AUX_PWR R3 Table 31. Impedance Compensation Signals Signal ZN_COMP Pin T2 Signal ZP_COMP Pin Signal Pin Signal Pin R5 Table 32. SMB Signals Signal SMBCLK Pin A14 Signal SMBDATA Pin A15 SMBALRT# A16 Table 33. EEPROM Interface Signals Signal Pin EE_DI C19 EE_DO B20 Signal EE_CS Pin C20 Signal EE_SK Pin D20 Table 34. Flash Interface Signals Signal 46 Pin Signal Pin Signal Pin FL_ADDR[0] F16 FL_ADDR[10] G17 FL_OE# K18 FL_ADDR[1] E18 FL_ADDR[11] G16 FL_WE# C17 FL_ADDR[2] E16 FL_ADDR[12] B15 FL_DATA[0]/LAN_ DISABLE H16 FL_ADDR[3] E15 FL_ADDR[13] D19 FL_DATA[1] G18 FL_ADDR[4] E14 FL_ADDR[14] D18 FL_DATA[2] J16 FL_ADDR[5] E13 FL_ADDR[15] C15 FL_DATA[3] H18 FL_ADDR[6] D15 FL_ADDR[16] D16 FL_DATA[4] J17 Datasheet Networking Silicon -- 82545GM Table 34. Flash Interface Signals Signal Pin Signal Pin Signal Pin FL_ADDR[7] B16 FL_ADDR[17] C18 FL_DATA[5] J18 FL_ADDR[8] F17 FL_ADDR[18] D17 FL_DATA[6] K17 FL_ADDR[9] F18 FL_CS# H20 FL_DATA[7] K16 Pin Signal Table 35. LED Signals Signal Pin ACT# N1 LINK# M1 Signal LINK100# N4 LINK1000# Pin N3 Table 36. Software Definable Signals Signal Pin SDP[0] G4 SDP[1] G5 Signal SDP[6] Pin E12 Signal SDP[7] Pin E11 Table 37. PHY Signals Signal Pin Signal Pin Signal Pin XTAL1 A3 MDI0+ B2 MDI2+ D2 XTAL2 A4 MDI1- C1 MDI3- E1 REF E3 MDI1+ C2 MDI3+ E2 MDI0- B1 MDI2- D1 Table 38. Serializer/Deserializer (SERDES) Signals Signal Pin Signal Pin RX+ G19 TX+ F19 RX- G20 TX- F20 Signal SIG_DETECT Pin E20 Table 39. Test Interface Signals Signal Datasheet Pin Signal Pin Signal Pin JTAG_TCK P1 JTAG_TMS P5 CLK_VIEW P3 JTAG_TDI P4 JTAG_RST# N5 TEST# A8 JTAG_TDO P2 47 82545GM -- Networking Silicon Table 40. Power Support Signals Signal CTRL_15 Pin A18 Signal CTRL_25 Pin Signal Pin Pin Signal Pin F2 Table 41. Digital Power Signals Signal Pin Signal VDDO (3.3V) B8 VDDO (3.3V) U7 DVDD (1.5V) H13 VDDO (3.3V) B14 VDDO (3.3V) U11 DVDD (1.5V) H14 VDDO (3.3V) B19 VDDO (3.3V) U15 DVDD (1.5V) J7 VDDO (3.3V) C10 VDDO (3.3V) U19 DVDD (1.5V) J14 VDDO (3.3V) C16 VDDO (3.3V) W1 DVDD (1.5V) M7 VDDO (3.3V) D6 VDDO (3.3V) W5 DVDD (1.5V) M14 VDDO (3.3V) D11 VDDO (3.3V) W9 DVDD (1.5V) N7 VDDO (3.3V) E17 VDDO (3.3V) W13 DVDD (1.5V) N8 VDDO (3.3V) H4 VDDO (3.3V) W17 DVDD (1.5V) N13 VDDO (3.3V) H19 DVDD (1.5V) G7 DVDD (1.5V) N14 VDDO (3.3V) L17 DVDD (1.5V) G8 DVDD (1.5V) P7 VDDO (3.3V) M2 DVDD (1.5V) G9 DVDD (1.5V) P8 VDDO (3.3V) N19 DVDD (1.5V) G12 DVDD (1.5V) P9 VDDO (3.3V) R4 DVDD (1.5V) G13 DVDD (1.5V) P12 VDDO (3.3V) R17 DVDD (1.5V) G14 DVDD (1.5V) P13 VDDO (3.3V) U1 DVDD (1.5V) H7 DVDD (1.5V) P14 VDDO (3.3V) U3 DVDD (1.5V) H8 Signal Pin Signal Pin Table 42. Analog Power Signals Signal Pin AVDDH (3.3 V) B4 AVDDL (2.5 V) G1 AVDDL (2.5 V) L2 AVDDH (3.3 V) F1 AVDDL (2.5 V) G2 AVDDL (2.5 V) L5 AVDDL (2.5 V) A19 AVDDL (2.5 V) G3 AVDDL (2.5 V) L18 Table 43. Grounds and No Connect Signals Signal 48 Pin Signal Pin Signal Pin GND A1 GND K12 NC A13 GND A2 GND K13 NC B12 GND A5 GND K14 NC B13 GND A10 GND L7 NC C12 GND B3 GND L8 GND W15 Datasheet Networking Silicon -- 82545GM Table 43. Grounds and No Connect Signals Signal Pin Signal Pin Signal Pin GND B6 GND L9 GND W19 GND B11 GND L10 NC A11 GND B17 GND L11 NC A12 GND C3 GND L12 NC C13 GND D3 GND L13 NC C14 GND D8 GND L14 NC D12 GND D14 GND L19 NC D13 GND E19 GND M4 NC F4 GND F3 GND M8 NC F5 GND G10 GND M9 NC H1 GND G11 GND M10 NC H3 GND H2 GND M11 NC H5 GND H9 GND M12 NC J1 GND H10 GND M13 NC J2 GND H11 GND N9 NC J3 GND H12 GND N10 NC J4 GND H17 GND N11 NC J5 GND J8 GND N12 NC J19 GND J9 GND N17 NC J20 GND J10 GND P10 NC K1 GND J11 GND P11 NC K3 GND J12 GND R2 NC K19 GND J13 GND R19 NC K20 GND K2 GND U5 NC L1 GND K4 GND U9 NC L3 GND K5 GND U13 NC L4 GND K7 GND U17 NC M3 GND K8 GND V2 NC N2 NC T1 GND K9 GND W3 GND K10 GND W7 GND K11 GND W11 Table 44. Reserved Signals Signal Datasheet Pin Signal Pin Signal Pin Reserved[0] D4 Reserved[11] Reserved[1] D5 Reserved[12] B7 Reserved[22] B10 A7 Reserved[23] C6 Reserved[2] C4 Reserved[13] C8 Reserved[24] A20 49 82545GM -- Networking Silicon Table 44. Reserved Signals Signal 50 Pin Signal Reserved[3] E4 Reserved[14] Reserved[4] C5 Reserved[15] Reserved[5] E5 Reserved[16] Reserved[6] B5 Reserved[17] Reserved[7] E6 Reserved[8] D7 Reserved[9] Reserved[10] Pin Signal Pin E8 Reserved[25] B18 E9 Reserved[26] M5 D9 Reserved[27] E7 C9 Reserved[28] A6 Reserved[18] B9 Reserved[29] R1 Reserved[19] D10 Reserved[30] L20 C7 Reserved[20] A9 E10 Reserved[21] C11 Datasheet Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Intel: PC82545GM S L87X PC82545GM 867806 RC82545GM S L775