DS272990484 - 3M - Product.Network

3M™Scotch-Weld™EPX

Two-component structural adhesives and applicator guns

Innovation

Even a bonded area of 10 cm2(like

in this picture) is sufficient to lift an

average family car off the ground! In

general, these structural adhesives

have enough cohesive strength and

creep resistance to permanently

bond high-strength materials and

they have the potential to replace mechanical and fusion fastening in

many applications.

The aircraft industry is one of the pioneers in use of structural

adhesives. Many other industries have also been taking advantage of

3M’s advanced formulations and innovative dispensing.

The 3MTM EPX application system for 2-component structural adhe-

sives provides quick, economic, clean, precise processing and quick

set-up times. It consists of:

EPX manual applicators or EPX air-powered applicators

Two-component adhesives in double cartridges

Static mixing nozzles

The adhesive can be applied at selected points or in a continuous

bead. Dosing, mixing and application are all achieved in one action,

delivering constant, defined quality. These 3M structural adhesives

achieve permanent high strength bonds with many materials such

as metals, glass, ceramics, wood, technical plastics and rubbers etc.

What is a structural adhesive?

Specifications

Product no. Description

Adhesive type

EPOXY formulations

DP 100 For metals, glass, ceramics and other materials. High shear strength for static loads.

rigid Excellent flow behaviour, therefore also well suited for potting. UL-listed.

DP 105 Particularly for materials with different, high expansion factors. High strength.

highly flexible Very good flow behaviour, therefore also very well suited for potting.

DP 110 Especially good for bonding metal and plastic, for static and dynamic loads.

thoughened

DP 125 Especially good for bonding plastic and for metals, where flexibility and peel strength are required.

flexible As DP 190, but with quicker time to handling strength.

DP 190 Especially good for bonding plastic and some types of rubber, as well as for metals,

flexible when flexibility and peel strength are required. UL-listed.

DP 270 Especially good for electronics. For potting, protection and sealing. No corrosion on copper, minimal exothermal

fluid reaction (heat development) and shrinkage (therefore also for bonding optical parts, e.g. lenses). UL-listed.

DP 410 Outstanding stability under static and dynamic loads. High resistance to impact.

thoughened Very good strength and excellent ageing characteristics.

DP 460 As DP 410, but longer work life. UL-listed.

thoughened

DP 490 As DP 410, but with high temperature resistance (120°C).

thoughened Thixotropic formulation, non-sag properties enable easy application to vertical surfaces.

DP 760 Especially for applications that require very high temperature resistance (230°C).

rigid

POLYURETHANE formulations

DP 609 Especially for plastics and wood. Good peel strength, viscosity and flexibility. Minimal flow.

flexible

DP 610 As DP609, but transparent, non-yellowing UV-resistant characteristics make it ideal for applications that require

flexible long term transparency and good visual effect. Good flow behaviour.

ACRYLIC formulations

DP 801 Very good for plastics, elastomers and metals. Good resistance to impact. For static and dynamic loads.

thoughened Short work life results in a fast development to handling strength.

DP 810 As DP 801, but longer work life. Significantly less odour that most acrylic adhesives.

thoughened

DP 8005 New, innovative product especially for bonding Low Surface Energy plastics (like PE or PP) together

thoughened or with other materials, without surface pre-treatment.

DP 8010 As above, longer work life of 10 minutes.

thoughened

3M’s high-strength structural adhesives are fundamentally load-bearing formulations. Bond strength is often as strong as, or stronger than

the materials joined.

Product No. Colour Mix ratio (B:A) Work life Time to handling Viscosity Shear strength Peel strength Temperature

(minutes) strength (Aluminium, MPa) (Aluminium, N/cm)

-55°C +23°C +80°C

EPOXY formulations

DP 100 transparent 1:1 3 to 5 min. 15 min. fluid 6 9 2 4 -50 to 80°C

DP 105 transparent 1:1 4 to 5 min. 20 min. fluid 24 14 2 62 -50 to 80°C

DP 110 translucent 1:1 8 to 10 min. 20 min controlled flow 14 18 1 35 -50 to 80°C

or grey

DP 125 grey 1:1 25 min. 2 to 3 hrs controlled flow 24 24 3 62 -50 to 80°C

DP 190 grey 1:1 90 min. 4 to 6 hrs controlled flow 11 18 3 21 -50 to 80°C

DP 270 transparent 1:1 60 to 70 min. 4 to 6 hrs fluid 8 17 2 <4 -50 to 80°C

or black

DP 410 off white 2:1 8 to 10 min. 30 min. thixotropic 29 34 8 100 -50 to 80°C

DP 460 off white 2:1 60 min. 4 to 6 hrs controlled flow 31 31 5 107 -50 to 80°C

DP 490 black 2:1 180 min. 4 hrs thixotropic 24 30 12 92 -50 to 120°C

DP 760 white 2:1 45 to 60 min. 4 to 6 hrs thixotropic 20 29 24 60 -50 to 230°C

POLYURETHANE formulations

DP 609 off white 1:1 7 min. 45 min. low 17 14 2 70 -50 to 80°C

DP 610 clear 1:1 10 min. 2 hrs fluid 34 23 3 78 -50 to 80°C

ACRYLIC formulations

DP 801 green 1:1 1 to 2 min. 7 min. controlled flow 19 13 2 24 -50 to 80°C

DP 810 green 1:1 8 min. 10 to 15 min. controlled flow 8 30 3 52 -50 to 80°C

DP 8005 white 10:1 2 to 3 min. 90 min. thixotropic low 12* 6* 2* 28** -50 to 80°C

DP 8010 white 10:1 10 min. 120 min. thixotropic 6* 10* 2* 28** -50 to 80°C

* PP/PP ** HDPE

Rigid adhesive types for applications with static loading

and high shear strength (DP 100, DP 270, DP 760)

Flexible adhesive types for dynamic and shock loads (DP 105,

DP 125, DP 190, DP 609, DP 610)

Toughened adhesive types which combine the advantages of hard

and flexible types, i.e. with good peel strength, high shear strength

and good impact resistance (DP 110, DP 410, DP 460, DP 490, DP

801, DP 810)

Useful adhesive terminology

Structural Adhesive = Practical bond strength is at least 7 MPa

in overlap shear at 24° C.

Handling strength = the time it takes assembled parts to reach

a strength where further handling and processing can take place.

Time will be dependant on the surface to be bonded, temperature

and humidity.

Work life = the time during which an adhesive is liquid enough

to adequately wet-out on a substrate.

MPa = 1 MPa = 1 N/mm2= 145 psi

N/cm = Newton / 1 cm width.

Critical adhesive characteristics

EPX Adhesives Preselection

Work life vs. Handling strength

Product

DP 100

DP 105

DP 110

DP 125

DP 190

DP 270

DP 410

DP 460

DP 490

DP 760

DP 609

DP 610

DP 801

DP 810

DP 8005

DP 8010

0 50 100 150 200 250 300

Work life

Handling strenght

minutes

520

10 20

25 180

90 300

10 30

180 240

745

10 120

815

390

10 120

Sheer vs. Peel Strength on etched aluminium

0 20 40 60 80 100 120

DP 810

N/cm

MPa

300

DP 190

DP 270

DP 100

DP 8005

DP 8010

DP 110

DP 105

DP 125

DP 760

DP 609

DP 610

DP 490

DP 460

DP 410

0 5 10 60 145 180

Work life

(minutes)

Viscosity vs. Worklife

very fluid

fluid

controlled

flow

thixotropic

DP 100

DP 110

DP 270

DP 105

DP 125

DP 460

DP 410

9025

Fluid / Short Work life

Less Fluid / Short Work life

Fluid / Long Work life

Less Fluid / Long Work life

Tensile stress is exerted equally over the entire joint and

away from the adhesive bond.

Shear stress is across the adhesive bond. The bonded

materials are forced to slide over each other.

Cleavage stress is concentrated at one edge and exerts a

prying force on the bond.

Peel stress is concentrated along a thin line at the bond’s

edge. One surface is flexible.

Most applications are subject to a combination of stresses.

Cleavage Peel

Tensile Shear

DP 801

DP 490

DP 760

DP 609

DP 610

DP 801

DP 810

DP 8005 DP 8010

DP 190

Operation Instructions

The EPX system of controlled two-component structural adhesives enables bonding operations to be carried out quickly, with precision and in

four simple steps:

Applications and benefits

The 3M™ Scotch-Weld™ EPX structural adhesives range is widely used in product assembly where high mechanical performance is required,

and also for sealing and potting in electrical / electronic applications.

The EPX structural adhesives offer significant advantages – at a low investment cost:

Reducing costs for combining different materials for the same or better performance;

Eliminating secondary sealing or finishing operations, saving time and money;

Achieving stronger and stiffer structures by improving stress distribution;

Joining a wide variety of materials that are unable to be assembled by traditional methods of fastening.

Slip the cartridge into the dispenser

and close the dispenser’s lock.

Unscrew the tip of the cartridge and

fix the nozzle on the cartridge.

Pull the trigger for exact dispensing,

the two components are mixed and

applied at once.

The result is a clean and precise

application without the user coming

into contact with the adhesive.

Bonding a golf club head to shaft.

3M Scotch-Weld DP 810

Bonding a seat cover to the ABS moulding

3M Scotch-Weld DP 190

Bonding a magnet to a steel rotor

3M Scotch-Weld DP 460

Bonding tubular joints for high impact applications

3M Scotch-Weld DP 490

Encapsulating memory chips to protect against

hacking of a digital set-top box

3M Scotch-Weld DP 760

Bonding automotive interior parts (PU) to the dash-

board (PP)

3M Scotch-Weld DP 8005

EPX manual applicator

complete with plunger 1:1/2:1 - suitable for 50 ml cartridges.

Note: for 38 ml 10:1 cartridges (DP 8005, DP8010), a 10:1

plunger is also required

EPX air-powered applicator

for 1:1 and 2:1 50 ml cartridges

EPX air-powered applicator 8501

for 1:1 and 2:1 400 ml cartridges

EPX air-powered applicator (not shown)

for DP 8005, DP 8010, 265 ml cartridges

Supply form: Duo pack cartridges

1:1 and 2:1 mix ratio = 50 ml and 400 ml

10:1 mix ratio = 38 ml and 265 ml

Bulk versions on request

The EPX applicators

Important Notice:

All declarations, technical information and recommendations in this

brochure are based on tests we believe to be reliable, but we are unable

to guarantee their complete accuracy. Before using our product, please

make sure it is suitable for the intended use. Any question concerning

the reliability of 3M adhesives is subject to the applications of the terms

and conditions of sale and any applicable legislation.

3M and Scotch-Weld are registered trademarks of the 3M Company.

The EPX accessoires

EPX plunger for EPX manual applicator:

Type 1:1/2:1 for all 50 ml cartridges

Type 10:1 for 38 ml cartridge (DP 8005, DP 8010)

EPX mixing nozzles for cartridges:

Quadro nozzle for 50 ml cartridges

(except DP 8005, DP 8010)

17 Element nozzle for DP 8005, DP 8010, 38 ml

EPX mixing nozzles for large cartridges:

24 Element nozzle for all 400 ml cartridges

18 Element nozzle for DP 8005, DP 8010, 265 ml

cartridge

Equipment

The 3M™ Scotch-Weld™ EPX adhesive system includes:

Applicators

All the applicators are ergonomically designed to minimise fatigue and ensure the maximum ease of use, particularly in “hard to get at” applica-

tions. There are manual and air-powered guns for 50 ml cartridges and an air-powered gun for the 400 ml cartridges. The selection of a manual

or air-powered gun and the 50 ml or 400 ml cartridge depends upon the production requirement(s) for the application.

Air-powered applicator

The use of a compressed air feed enables operators to apply precisely the quantity of product required without interruption.

Manual applicator

The manual applicator is a light, reliable tool, which requires no special maintenance; it is particularly well suited to smaller scale use at multi-

ple work- stations.

Mixing Nozzles

The adhesive is extruded through a static mixing nozzle, which ensures that the two components are mixed together thoroughly every time.

The mixing nozzle can be adapted to extrude different bead diameters by cutting the tip.

CJ1015 - PE-BE-SB-18