T-1 (3mm) INFRARED EMITTING DIODE Part Number: L-7104SF6C Features Description z Mechanically and spectrally matched to the phototransistor. SF6 Made with Gallium Aluminum Arsenide Infrared Emit- z RoHS compliant. ting diodes. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAH2847 REV NO: V.4B DATE: OCT/17/2014 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029378 Selection Guide Part No. L-7104SF6C Dice Po (mW/sr) [2] @ 20mA Lens Type SF6 (GaAlAs) Water Clear Po (mW/sr) [2] @ 50mA Viewing Angle [1] Min. Typ. Min. Typ. 21/2 7 12 12 30 34 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. 3. Radiant intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] SF6 VF 1.35 1.6 V IF=20mA Reverse Current SF6 IR 10 uA VR = 5V Capacitance SF6 C 30 pF VF=0V;f=1MHz Peak Spectral Wavelength SF6 P 860 nm IF=20mA Spectral Bandwidth SF6 1/2 50 nm IF=20mA Notes: 1. Forward Voltage: +/-0.1V. 2. Wavelength value is traceable to the CIE127-2007 compliant national standards. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25C Parameter Symbol SF6 Units Power dissipation PD 80 mW DC Forward Current IF 50 mA Peak Forward Current [1] iFS 1 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 C TSTG -40 To +85 C Storage Temperature Lead Solder Temperature [2] 260C For 3 Seconds Lead Solder Temperature [3] 260C For 5 Seconds Notes: 1. 1/100 Duty Cycle, 10s Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAH2847 REV NO: V.4B DATE: OCT/17/2014 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029378 L-7104SF6C SPEC NO: DSAH2847 REV NO: V.4B DATE: OCT/17/2014 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029378 PACKING & LABEL SPECIFICATIONS L-7104SF6C Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes SPEC NO: DSAH2847 REV NO: V.4B DATE: OCT/17/2014 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029378 SPEC NO: DSAH2847 REV NO: V.4B DATE: OCT/17/2014 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029378 SPEC NO: DSAH2847 REV NO: V.4B DATE: OCT/17/2014 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: P.Cheng ERP: 1101029378