S8055MTP - Littelfuse, Inc.

295

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Main Features

Symbol Value Unit

IT(RMS) 55 A

VDRM /VRRM 400 to 1000 V

IGT 40 mA

Absolute Maximum Ratings

Symbol Parameter Test Conditions Value Unit

IT(RMS) RMS on-state current TC = 90°C 55 A

IT(AV) Average on-state current TC = 90°C 35.0 A

ITSM Peak non-repetitive surge current

single half cycle; f = 50Hz;

TJ (initial) = 25°C 550

single half cycle; f = 60Hz;

TJ (initial) = 25°C 650

I2t I2t Value for fusing tp = 8.3 ms 1750 A2s

di/dt Critical rate of rise of on-state current f = 60Hz ; TJ = 125°C 175 A/μs

IGM Peak gate current TJ = 125°C

PW = 10µS 4.0 A

PG(AV) Average gate power dissipation TJ = 125°C 0.8 W

Tstg Storage temperature range -40 to 150 °C

TJOperating junction temperature range -40 to 125 °C

Description

Excellent unidirectional switches for phase control

applications such as heating and motor speed controls.

Standard phase control SCRs are triggered with few

milliamperes of current at less than 1.5V potential.

Features & Beneﬁts

• RoHS compliant

• Glass – passivated

junctions

• Voltage capability up

to 1000 V

• Surge capability up to

650 A

Schematic Symbol

Applications

Typical applications are AC solid-state switches, industrial

power tools, exercise equipment, white goods and

commercial appliances.

296

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Electrical Characteristics (TJ = 25°C, unless otherwise speciﬁed)

Symbol Test Conditions Value Unit

IGT VD = 12V; RL = 30 Ω

MAX. 40

MIN. 5

VGT MAX. 1. 5 V

dv/dt

VD = VDRM; gate open; TJ = 100°C

400V

MIN.

650

V/μs

600V 600

800V 500

1000V 250

VD = VDRM; gate open; TJ = 125°C

400V 550

600V 500

800V 475

VGD VD = VDRM; RL = 3.3 kΩ; TJ = 125°C MIN. 0.2 V

IHIT = 400mA (initial) MAX. 60 mA

tq(1) MAX. 35 μs

tgt IG = 2 x IGT; PW = 15µs; IT = 110A TYP. 2.5 μs

Note :

(1) IT=2A; tp=50µs; dv/dt=5V/µs; di/dt=-30A/µs

Thermal Resistances

Symbol Parameter Value Unit

Rθ(J-C) Junction to case (AC)

Sxx55R

Sxx55N 0.5

°C/W

Sxx55W

Sxx55M 0.53

Rθ(J-A) Junction to ambient Sxx55R 40 °C/W

Note: xx = voltage

Static Characteristics

Symbol Test Conditions Value Unit

VTM IT = 110A; tp = 380μs MAX. 1. 8 V

IDRM / IRRM VDRM / VRRM

TJ = 25°C

400 – 600V

MAX.

μA

800 V 20

1000 V 30

TJ = 100°C

400 – 600V 1000

800V 1500

1000V 5000

TJ = 125°C

400 – 600V 2000

800V 3000

297

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Figure 1: Normalized DC Gate Trigger Current

vs. Junction Temperature

Figure 2: Normalized DC Gate Trigger Voltage

vs. Junction Temperature

125

0.0

0.5

1.0

1.5

2.0

-40-15 10 35 60 85 110

Junction Te mperature (TJ) -- (°C)

Ratio of IGT/ IGT (TJ = 25°C)

Figure 5: Power Dissipation (Typical)

vs. RMS On-State Current

Figure 6: Maximum Allowable Case Temperature

vs. RMS On-State Current

Figure 3: Normalized DC Holding Current

vs. Junction Temperature

Figure 4: On-State Current vs. On-State Voltage

(Typical)

125

0.0

0.5

1.0

1.5

2.0

-40 -1510356085110

Junction Te mperature (TJ) -- (°C)

Ratio of VGT/ VGT (TJ = 25°C)

125

0.0

0.5

1.0

1.5

2.0

-40-15 10 35 60 85 110

Ratio of IH/ IH (TJ= 25°C)

Junction Te mperature (TJ) -- (°C)

TJ = 25°C

100

120

0.7 0.8 0.9 1.01.1 1.21.3 1.41.5 1.6

Instantaneous On-state Voltage (vT) – Volts

Instantaneous On-state Current

(iT) – Amps

0510 15 20 25 30 35 40 45 50 55

RMS On-State Current [IT(RMS)] - (Amps)

Average On-State Power Dissipation

[PD(AV)] - (Watts)

100

105

110

115

120

125

130

0510 15 20 25 30 35 40 45 50 55 60

Maximum Allowable Case Temperature

(TC) - °C

RMS On-State Current [IT(RMS)] - Amps

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

The "R" or "M" package rating is intended

for high surge condition use only and not

recommended for >50A rms continuous

current use since narrow pin leads depend-

ing on lead length can exceed PCB solder

melting temperature. "W" package is

recommended for >50A rms continuous

current requirements.

Note: xx = voltage

298

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Figure 7: Maximum Allowable Case Temperature

vs. Average On-State Current

Figure 8: Maximum Allowable Ambient Temperature

vs. RMS On-State Current

Figure 9: Maximum Allowable Ambient Temperature

vs. Average On-State Current

100

105

110

11 5

120

125

130

0510 15 20 25 30 35 40

Average On-State Current [IT(AVE)] - Amps

Maximum Allowable Case Temperature

(TC) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

The "R" or "M" package rating is intended for high

surge condition use only and not recommended

for >32A (AV) continuous current use since narrow

pin leads depending on lead length can exceed

PCB solder melting temperature. "W" package is

recommended for >32A (AV) continuous current

requirements.

100

120

0.0 0.5 1.01.5 2.0 2.5

RMS On-State Current [IT(RMS)] - Amps

Maximum Allowable Ambient

Temperature (TA) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

FREE AIR RATING

100

120

0.0 0.5 1.

Average On-State Current [IT(AVE)] - Amps

Maximum Allowable Ambient Temperature

) - °C

CURRENT WAVEFORM: Sinusoidal

LOAD: Resistive or Inductive

CONDUCTION ANGLE: 180°

FREE AIR RATING

Figure 10: Peak Capacitor Discharge Current Figure 11: Peak Capacitor Discharge Current Derating

100

1000

10000

0.51.0 10.0 50.0

Peak Discharge Current (ITM) - Amps

Pulse Current Duration (tw) - ms

ITRM

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0255075100 12

Normalized Peak Current

Case Te mperature (TC) - °C

Note: xx = voltage

299

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

100

1000

110100 1000

Surge Current Duration -- Full Cycles

Peak Surge (Non-repetitive)

On-state Current (ITSM) – Amps

Figure 12: Surge Peak On-State Current vs. Number of Cycles

SUPPLY FREQUENCY: 60 Hz Sinusoidal

LOAD: Resistive

RMS On-State Current: [IT(RMS)]: Maximum Rated

Value at Speciﬁed Case Temperature

Notes:

1. Gate control may be lost during and immediately

following surge current interval.

2. Overload may not be repeated until junction

temperature has returned to steady-state

rated value.

Soldering Parameters

Reﬂow Condition Pb – Free assembly

Pre Heat

- Temperature Min (Ts(min))150°C

- Temperature Max (Ts(max))200°C

- Time (min to max) (ts)60 – 180 secs

Average ramp up rate (Liquidus Temp)

(TL) to peak 5°C/second max

TS(max) to TL - Ramp-up Rate 5°C/second max

Reﬂow - Temperature (TL) (Liquidus) 217°C

- Temperature (tL)60 – 150 seconds

Peak Temperature (TP)260+0/-5 °C

Time within 5°C of actual peak

Temperature (tp)20 – 40 seconds

Ramp-down Rate 5°C/second max

Time 25°C to peak Temperature (TP)8 minutes Max.

Do not exceed 280°C

Time

Temperature

TS(max)

TS(min)

time to peak temperature

Preheat

eat

Ramp-upRamp-up

Ramp-down

300

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Physical Speciﬁcations Environmental Speciﬁcations

Test Speciﬁcations and Conditions

AC Blocking MIL-STD-750, M-1040, Cond A Applied

Peak AC voltage @ 125°C for 1008 hours

Temperature Cycling

MIL-STD-750, M-1051,

100 cycles; -40°C to +150°C;

15-min dwell-time

Temperature/

Humidity

EIA / JEDEC, JESD22-A101

1008 hours; 320V - DC: 85°C;

85% rel humidity

High Temp Storage MIL-STD-750, M-1031,

1008 hours; 150°C

Low-Temp Storage 1008 hours; -40°C

Thermal Shock

MIL-STD-750, M-1056

10 cycles; 0°C to 100°C; 5-min dwelltime

at each temperature; 10 sec (max) transfer

time between temperature

Autoclave

EIA / JEDEC, JESD22-A102

168 hours (121°C at 2 ATMs) and

100% R/H

Resistance to

Solder Heat MIL-STD-750 Method 2031

Solderability ANSI/J-STD-002, category 3, Test A

Lead Bend MIL-STD-750, M-2036 Cond E

Terminal Finish 100% Matte Tin-plated

Body Material UL recognized epoxy meeting ﬂammability

classiﬁcation 94V-0

Lead Material Copper Alloy

Design Considerations

Careful selection of the correct device for the application’s

operating parameters and environment will go a long way

toward extending the operating life of the Thyristor. Good

design practice should limit the maximum continuous

current through the main terminals to 75% of the device

rating. Other ways to ensure long life for a power discrete

semiconductor are proper heat sinking and selection of

voltage ratings for worst case conditions. Overheating,

overvoltage (including dv/dt), and surge currents are

the main killers of semiconductors. Correct mounting,

soldering, and forming of the leads also help protect

against component damage.

Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead

Dimension Inches Millimeters

Min Max Min Max

A 0.380 0.420 9.65 10.67

B 0.105 0.115 2.67 2.92

C 0.230 0.250 5.84 6.35

D 0.590 0.620 14.99 15.75

E 0.142 0.147 3.61 3.73

F 0.110 0.130 2.79 3.30

G 0.540 0.575 13.72 14.61

H 0.025 0.035 0.64 0.89

J 0.195 0.205 4.95 5.21

K 0.095 0.105 2.41 2.67

L 0.060 0.075 1.52 1.91

M 0.085 0.095 2.16 2.41

N 0.018 0.024 0.46 0.61

O 0.178 0.188 4.52 4.78

P 0.045 0.060 1. 14 1.52

R 0.038 0.048 0.97 1.22

MEASURING POINT

ANODE

.276

7. 01

.526

13.36

.320

8.13

AREA (REF.) 0.17 IN

NOTCH IN

GATE LEAD

TO ID.

NON-ISOLATED

TAB

GATECATHODE ANODE

Note: Maximum torque to

be applied to mounting tab

is 8 in-lbs. (0.904 Nm).

301

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Dimensions – TO-263AB (N-package) — D2-Pak Surface Mount

Dimension Inches Millimeters

Min Max Min Max

A 0.360 0.370 9.14 9.40

B 0.380 0.420 9.65 10.67

C 0.178 0.188 4.52 4.78

D 0.025 0.035 0.63 0.89

E 0.048 0.055 1.22 1.40

F 0.060 0.075 1.52 1.91

G 0.095 0.105 2.41 2.67

H 0.083 0.093 2.11 2.36

J 0.018 0.024 0.46 0.61

K 0.090 0.110 2.29 2.79

S 0.590 0.625 14.99 15.87

V 0.035 0.045 0.89 1. 14

U 0.002 0.010 0.05 0.25

W 0.040 0.070 1.02 1.78

CATHODE

ANODE

MEASURING POINT

.320

8.13

.276

7. 01

.331

8.41

GATE

.460

11.68

.665

16.89

.260

6.60

.150

3.81

.080

2.03

.085

2.16

.055

1.40

.350

8.89

.276

7. 01

.276

7. 01

AREA: 0.11 in 2

Dimensions – TO-218X (W Package) — Non-Isolated Mounting Tab Common with Center Lead

Dimension Inches Millimeters

Min Max Min Max

A 0.810 0.835 20.57 21.21

B 0.610 0.630 15.49 16.00

C 0.178 0.188 4.52 4.78

D 0.055 0.070 1.40 1.78

E 0.487 0.497 12.37 12.62

F 0.635 0.655 16.13 16.64

G 0.022 0.029 0.56 0.74

H 0.075 0.095 1.91 2.41

J 0.575 0.625 14.61 15.88

K 0.256 0.264 6.50 6.71

L 0.220 0.228 5.58 5.79

M 0.080 0.088 2.03 2.24

N 0.169 0.177 4.29 4.49

P 0.034 0.042 0.86 1.07

R 0.113 0.121 2.87 3.07

S 0.086 0.096 2.18 2.44

T 0.156 0.166 3.96 4.22

U 0.164 0.165 4.10 4.20

V 0.603 0.618 15.31 15.70

W 0.000 0.005 0.00 0.13

X 0.003 0.012 0.07 0.30

Y 0.028 0.032 0.71 0.81

Z 0.085 0.095 2.17 2.42

U (diameter)

CATHODE

ANODE

Measurement

Point

GATE

Note: Maximum torque to

be applied to mounting tab

is 8 in-lbs. (0.904 Nm).

302

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

Dimensions – TO-218AC (M Package) — Non-isolated Mounting Tab Common with Center Lead

Dimension Inches Millimeters

Min Max Min Max

A 0.810 0.835 20.57 21.21

B 0.610 0.630 15.49 16.00

C 0.178 0.188 4.52 4.78

D 0.055 0.070 1.40 1.78

E 0.487 0.497 12.37 12.62

F 0.635 0.655 16.13 16.64

G 0.022 0.029 0.56 0.74

H 0.075 0.095 1.91 2.41

J 0.575 0.625 14.61 15.88

K 0.211 0.219 5.36 5.56

L 0.422 0.437 10.72 11. 10

M 0.058 0.068 1.47 1.73

N 0.045 0.055 1. 14 1.40

P 0.095 0.115 2.41 2.92

Q 0.008 0.016 0.20 0.41

R 0.008 0.016 0.20 0.41

U 0.164 0.165 4.10 4.20

W 0.085 0.095 2.17 2.42

Tc Measurement Point

U (diameter)

ANODE

GATE

ANODE

CATHODE

Note: Maximum torque

to be applied to mounting

tab is 8 in-lbs. (0.904 Nm).

Product Selector

Part Number Voltage Gate Sensitivity Type Package

400V 600V 800V 1000V

Sxx55R X X X X 40mA Standard SCR TO-220R

Sxx55N X X X X 40mA Standard SCR TO-263

Sxx55W X X X 40mA Standard SCR TO-218X

Sxx55M X X X X 40mA Standard SCR TO-218AC

Note: xx = Voltage

Packing Options

Part Number Marking Weight Packing Mode Base Quantity

Sxx55R Sxx55R 2.2g Bulk 500

Sxx55RTP Sxx55R 2.2g Tube 500 (50 per tube)

Sxx55NTP Sxx55N 1.6g Tube 500 (50 per tube)

Sxx55NRP Sxx55N 1.6g Embossed Carrier 500

Sxx55WTP Sxx55W 5.23g Tube 250 (25 per tube)

Sxx55MTP Sxx55M 4.40g Tube 250 (25 per tube)

Note: xx = Voltage

303

Revised: June 24, 2011 04:57 PM

Teccor® brand Thyristors

Speciﬁcations are subject to change without notice.

Please refer to http://www.littelfuse.com for current information.

55 Amp Standard SCRs

Sxx55x Series

TO-263 Embossed Carrier Reel Pack (RP) Speciﬁcation

Gate

Cathode

Anode

0.512 (13.0) Arbor

Hole Dia.

0.945

(24.0)

0.63

(16.0)

1.01

(25.7)

12.99

(330.0)

0.827

(21.0)

0.157

(4.0)

Direction of Feed

Dimensions

are in inches

(and millimeters).

*Cover tape

0.059 DIA

(1.5)

Meets all EIA-481-2 Standards

Part Numbering System Part Marking System

DEVICE TYPE

S: SCR

xx: Lead Form Option

PACKAGE TYPE

R: TO-220 (Non-isolated)

M: TO-218AC (Non-isolated)

W: TO-218X (Non-isolated)

N: TO-263 (D

CURRENT RATING

Lead Form Dimensions

55: 55A

VOLTAGE RATING

40: 400V

60: 600V

80: 800V

K0: 1000V

SENSITIVITY & TYPE

S6055R

[blank]: 40mA

2- Pak)

TO-218AC - (M Package)

TO-218X - (W Package)

YMLXX

S6055M

S6055R