LTC2655 Quad I2C 16-/12-Bit Rail-to-Rail DACs with 10ppm/C Max Reference DESCRIPTION FEATURES n n n n n n n n n n The LTC(R)2655 is a family of Quad I2C 16-/12-Bit Rail-toRail DACs with integrated 10ppm/C max reference. The DACs have built-in high performance, rail-to-rail, output buffers and are guaranteed monotonic. The LTC2655-L has a full-scale output of 2.5V with the integrated reference and operates from a single 2.7V to 5.5V supply. The LTC2655-H has a full-scale output of 4.096V with the integrated reference and operates from a 4.5V to 5.5V supply. Each DAC can also operate with an external reference, which sets the full-scale output to 2 times the external reference voltage. Integrated Reference 10ppm/C Max Maximum INL Error: 4LSB at 16 Bits Guaranteed Monotonic Over Temperature Selectable Internal or External Reference 2.7V to 5.5V Supply Range (LTC2655-L) Integrated Reference Buffers Ultralow Crosstalk Between DACs (<1nV*s) Power-On-Reset to Zero-Scale/Mid-Scale Asynchronous DAC Update Pin Tiny 20-Lead 4mm x 4mm QFN and 16-Lead Narrow SSOP packages The parts use the 2-wire I2C compatible serial interface. The LTC2655 operates in both the standard mode (maximum clock rate of 100kHz) and the fast mode (maximum clock rate of 400kHz). The LTC2655 incorporates a power-on reset circuit that is controlled by the PORSEL pin. If PORSEL is tied to GND the DACs power-on reset to zero-scale. If PORSEL is tied to VCC, the DACs power-on reset to mid-scale. APPLICATIONS n n n n n Mobile Communications Process Control and Industrial Automation Instrumentation Automatic Test Equipment Automotive L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 5396245, 6891433 and 7671770. BLOCK DIAGRAM REFCOMP REFIN/OUT INTERNAL REFERENCE INL Curve GND 4 VCC CA1 32-BIT SHIFT REGISTER CA2 SCL DAC D 2 VOUTD INL (LSB) REGISTER REGISTER REGISTER REGISTER REGISTER REGISTER CA0 DAC B REGISTER VOUTB DAC A REGISTER VOUTA VCC = 5V 3 REFLO 1 0 -1 DAC C VOUTC -2 -3 POWER-ON RESET PORSEL SDA -4 128 16384 32768 CODE 49152 65535 2655 TA01b 2-WIRE INTERFACE LDAC 2655 BD 2655f 1 LTC2655 ABSOLUTE MAXIMUM RATINGS (Notes 1, 2) Supply Voltage (VCC) ................................... -0.3V to 6V SCL, SDA, LDAC, REFLO .............................. -0.3V to 6V VOUTA to VOUTD ................-0.3V to Min (VCC + 0.3V, 6V) REFIN/OUT, REFCOMP .....-0.3V to Min (VCC + 0.3V, 6V) PORSEL, CA0, CA1, CA2 ..-0.3V to Min (VCC + 0.3V, 6V) Operating Temperature Range LTC2655C ................................................ 0C to 70C LTC2655I .............................................-40C to 85C Maximum Junction Temperature .......................... 150C Storage Temperature Range ......................-65 to 150C Lead Temperature, GN Only (Soldering, 10 sec).... 300C PIN CONFIGURATION 15 VCC 3 14 VOUTD VOUTB 4 13 VOUTC REFIN/OUT 5 12 PORSEL LDAC 6 11 CA0 CA2 7 10 CA1 SCL 8 9 SDA GN PACKAGE 16-LEAD PLASTIC SSOP TJMAX = 150C, JA = 110C/W DNC DNC 15 DNC VOUTA 1 14 VOUTD REFCOMP 2 21 GND VOUTB 3 REFIN/OUT 4 13 VOUTC 12 PORSEL LDAC 5 11 CA0 6 7 8 9 10 CA1 2 SDA VOUTA REFCOMP 20 19 18 17 16 SCL 16 GND DNC 1 CA2 REFLO VCC TOP VIEW GND REFLO TOP VIEW UF PACKAGE 20-LEAD (4mm s 4mm) PLASTIC QFN TJMAX = 150C, JA = 37C/W EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB 2655f 2 LTC2655 ORDER INFORMATION LTC2655 B C UF -L 16 #TR PBF LEAD FREE DESIGNATOR TAPE AND REEL TR = Tape and Reel RESOLUTION 16 = 16-Bit 12 = 12-Bit FULL-SCALE VOLTAGE, INTERNAL REFERENCE MODE L = 2.5V H = 4.096V PACKAGE TYPE UF = 20-Lead (4mm x 4mm) Plastic QFN GN = 16-Lead Narrow SSOP TEMPERATURE GRADE C = Commercial Temperature Range (0C to 70C) I = Industrial Temperature Range (-40C to 85C) ELECTRICAL GRADE (OPTIONAL) B = 4LSB Maximum INL (16-Bit) PRODUCT PART NUMBER Consult LTC Marketing for information on non-standard lead based finish parts. Consult LTC Marketing for parts specified with wider operating temperature ranges. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2655f 3 LTC2655 PRODUCT SELECTION GUIDE TEMPERATURE RANGE MAXIMUM INL 16-Lead Narrow SSOP 0C to 70C 4 16-Lead Narrow SSOP -40C to 85C 4 20-Lead (4mm x 4mm) Plastic QFN 0C to 70C 4 20-Lead (4mm x 4mm) Plastic QFN -40C to 85C 4 16-Lead Narrow SSOP 0C to 70C 4 655H16 16-Lead Narrow SSOP -40C to 85C 4 LTC2655BCUF-H16#TRPBF 55H16 20-Lead (4mm x 4mm) Plastic QFN 0C to 70C 4 LTC2655BIUF-H16#TRPBF 55H16 20-Lead (4mm x 4mm) Plastic QFN -40C to 85C 4 LTC2655CGN-L12#TRPBF 655L12 16-Lead Narrow SSOP 0C to 70C 1 LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION LTC2655BCGN-L16#PBF LTC2655BCGN-L16#TRPBF 655L16 LTC2655BIGN-L16#PBF LTC2655BIGN-L16#TRPBF 655L16 LTC2655BCUF-L16#PBF LTC2655BCUF-L16#TRPBF 55L16 LTC2655BIUF-L16#PBF LTC2655BIUF-L16#TRPBF 55L16 LTC2655BCGN-H16#PBF LTC2655BCGN-H16#TRPBF 655H16 LTC2655BIGN-H16#PBF LTC2655BIGN-H16#TRPBF LTC2655BCUF-H16#PBF LTC2655BIUF-H16#PBF LTC2655CGN-L12#PBF LTC2655IGN-L12#PBF LTC2655IGN-L12#TRPBF 655L12 16-Lead Narrow SSOP -40C to 85C 1 LTC2655CUF-L12#PBF LTC2655CUF-L12#TRPBF 55L12 20-Lead (4mm x 4mm) Plastic QFN 0C to 70C 1 LTC2655IUF-L12#PBF LTC2655IUF-L12#TRPBF 55L12 20-Lead (4mm x 4mm) Plastic QFN -40C to 85C 1 LTC2655CGN-H12#PBF LTC2655CGN-H12#TRPBF 655H12 16-Lead Narrow SSOP 0C to 70C 1 LTC2655IGN-H12#PBF LTC2655IGN-H12#TRPBF 655H12 16-Lead Narrow SSOP -40C to 85C 1 LTC2655CUF-H12#PBF LTC2655CUF-H12#TRPBF 55H12 20-Lead (4mm x 4mm) Plastic QFN 0C to 70C 1 LTC2655IUF-H12#PBF LTC2655IUF-H12#TRPBF 55H12 20-Lead (4mm x 4mm) Plastic QFN -40C to 85C 1 Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2655f 4 LTC2655 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VOUT unloaded unless otherwise specified. LTC2655B-L16/ LTC2655-L12 (Internal Reference=1.25V) LTC2655-12 SYMBOL PARAMETER CONDITIONS MIN TYP LTC2655B-16 MAX MIN TYP MAX UNITS DC Performance Resolution l 12 12 16 Bits Monotonicity (Note 3) l DNL Differential Nonlinearity (Note 3) l 0.1 0.5 0.3 1 LSB INL Integral Nonlinearity (Note 3) VCC = 5.5V, VREF = 2.5V l 0.5 1 2 4 LSB Load Regulation VCC = 5V 10%, Internal Reference, Mid-Scale, -15mA IOUT 15mA l 0.04 0.125 0.6 2 LSB/mA VCC = 3V 10%, Internal Reference, Mid-Scale, -7.5mA IOUT 5mA l 0.06 0.25 1 4 LSB/mA Zero-Scale Error l 1 3 1 3 mV Offset Error l 1 2 1 2 ZSE VOS VREF = 1.25V (Note 4) VOS Temperature Coefficient GE Bits 5 l Gain Error Gain Temperature Coefficient 0.02 5 0.1 0.02 1 SYMBOL PARAMETER CONDITIONS VOUT DAC Output Span Internal Reference External Reference = VEXTREF PSR Power Supply Rejection VCC 10% ROUT DC Output Impedance VCC = 5V 10%, Internal Reference, Mid-Scale, -15mA IOUT 15mA VCC = 3V 10%, Internal Reference, Mid-Scale, -7.5mA IOUT 7.5mA ISC 16 0.1 1 MIN TYP mV V/C %FSR ppm/C MAX 0 to 2.5 0 to 2*VEXTREF UNITS V V -80 dB l 0.04 0.15 l 0.04 0.15 DC Crosstalk (Note 5) Due to Full-Scale Output Change Due to Load Current Change Due to Powering Down (per Channel) 1.5 2 1 V V/mA V Short-Circuit Output Current (Note 6) VCC = 5.5V VEXTREF = 2.8V Code: Zero-Scale; Forcing Output to VCC Code: Full-Scale; Forcing Output to GND l l 20 20 65 65 mA mA VCC = 2.7V VEXTREF = 1.4V Code: Zero-Scale; Forcing Output to VCC Code: Full-Scale; Forcing Output to GND l l 10 10 45 45 mA mA 2655f 5 LTC2655 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V, VOUT unloaded unless otherwise specified. LTC2655B-L16/LTC2655-L12 (Internal Reference = 1.25V) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 1.248 1.25 1.252 V 2 10 Reference Reference Output Voltage Reference Temperature Coefficient (Note 7) Reference Line Regulation VCC 10% Reference Short-Circuit Current VCC = 5.5V, Forcing REFIN/OUT to GND l 3 5 REFCOMP Pin Short-Circuit Current VCC = 5.5V, Forcing REFCOMP to GND l 65 200 Reference Load Regulation VCC = 3V10% or 5V10%, IOUT = 100A Sourcing 40 mV/mA Reference Output Voltage Noise Density CREFCOMP = CREFIN/OUT = 0.1F, at f = 1kHz 30 nV/Hz Reference Input Range External Reference Mode (Note 14) l 0.5 l Reference Input Current Reference Input Capacitance -80 0.001 (Note 9) ppm/C dB mA A VCC /2 V 1 A 20 pF Power Supply VCC Positive Supply Voltage For Specified Performance l ICC Supply Current (Note 8) VCC = 5V, Internal Reference On VCC = 5V, Internal Reference Off VCC = 3V, Internal Reference On VCC = 3V, Internal Reference Off l l l l ISD Supply Current in Shutdown Mode (Note 8) VCC = 5V VIL Low Level Input Voltage (SDA and SCL) VIH High Level Input Voltage (SDA and SCL) VIL(LDAC) Low Level Input Voltage (LDAC) 2.7 5.5 V 2.5 2 2.2 1.7 mA mA mA mA l 3 A l 0.3VCC V 1.7 1.3 1.6 1.2 Digital I/O VIH(LDAC) High Level Input Voltage (LDAC) l 0.7VCC V VCC = 4.5V to 5.5V l 0.8 V VCC = 2.7V to 4.5V l 0.6 V VCC = 3.6V to 5.5V l 2.4 V VCC = 2.7V to 3.6V l 2 V VIL(CA) Low Level Input Voltage (CA0 to CA2) See Test Circuit 1 l VIH(CA) High Level Input Voltage (CA0 to CA2) See Test Circuit 1 l RINH Resistance from CAn (n = 0,1,2) to VCC to Set CAn = VCC See Test Circuit 2 l 10 k RINL Resistance from CAn (n = 0,1,2) to GND to Set CAn = GND See Test Circuit 2 l 10 k RINF Resistance from CAn (n = 0,1,2) to VCC or GND to Set Can = FLOAT See Test Circuit 2 l 2 VOL Low Level Output Voltage Sink Current =3mA l 0 0.4 V tOF Output Fall Time VO = VIH(MIN) to VO = VIL(MAX), CB = 10pF to 400pF (Note 13) 20+0.1CB 250 ns tSP Pulse Width of Spikes Suppressed by Input Filter 0 50 ns IIN Input Leakage 0.1VCC VIN 0.9VCC l 1 A CIN I/O Pin Capacitance (Note 9) l 10 pF CB Capacitance Load for Each Bus Line l 400 pF CCAn External Capacitive Load on Address Pins CA0, CA1 and CA2 l 10 pF l 0.15VCC 0.85VCC V V M 2655f 6 LTC2655 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 4.5V to 5.5V, VOUT unloaded unless otherwise specified. LTC2655B-H16/LTC2655-H12 (Internal Reference = 2.048V) LTC2655-12 SYMBOL PARAMETER CONDITIONS MIN TYP LTC2655B-16 MAX MIN TYP MAX UNITS DC Performance Resolution DNL INL l 12 12 16 Monotonicity (Note 3) l Differential Nonlinearity (Note 3) l 0.1 Integral Nonlinearity (Note 3) VCC = 5.5V, VREF = 2.5V l 0.5 Load Regulation VCC = 5V 10%, Internal Reference, Mid-Scale, -15mA IOUT 15mA l 0.04 ZSE Zero-Scale Error VOS Offset Error VREF = 2.048V (Note 4) 16 0.3 1 1 2 4 LSB 0.125 0.6 2 LSB/mA 1 3 1 3 mV 1 2 1 2 mV l 0.02 0.1 0.02 5 Gain Error LSB l Gain Temperature Coefficient 5 1 SYMBOL PARAMETER CONDITIONS VOUT DAC Output Span Internal Reference External Reference = VEXTREF PSR Power Supply Rejection VCC 10% ROUT DC Output Impedance VCC = 5V 10%, Internal Reference, Mid-Scale, -15mA IOUT 15mA DC Crosstalk Due to Full Scale Output Change Due to Load Current Change Due to Powering Down (per Channel) Short-Circuit Output Current (Note 4) VCC = 5.5V VEXTREF = 2.8V Code: Zero-Scale; Forcing Output to VCC Code: Full-Scale; Forcing Output to GND ISC Bits 0.5 l VOS Temperature Coefficient GE Bits V/C 0.1 1 MIN l TYP ppm/C MAX V V -80 dB 0.04 20 20 UNITS 0 to 4.096 0 to 2*VEXTREF 0.15 1.5 2 1 l l %FSR V V/mA V 65 65 mA mA 2655f 7 LTC2655 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 4.5V to 5.5V, VOUT unloaded unless otherwise specified. LTC2655B-H16/LTC2655-H12 (Internal Reference = 2.048V) SYMBOL PARAMETER CONDITIONS MIN TYP MAX 2.044 UNITS Reference Reference Output Voltage 2.048 2.052 Reference Temperature Coefficient (Note 7) 2 10 Reference Line Regulation VCC 10% -80 Reference Short-Circuit Current VCC = 5.5V, Forcing REFIN/OUT to GND l 3 5 mA REFCOMP Pin Short-Circuit Current VCC = 5.5V, Forcing REFCOMP to GND l 65 200 A Reference Load Regulation VCC = 5V10%, IOUT = 100A Sourcing 40 mV/mA Reference Output Voltage Noise Density CREFCOMP = CREFIN/OUT = 0.1F, at f = 1kHz 35 nV/Hz Reference Input Range External Reference Mode (Note 14) 0.5 l 0.001 (Note 9) l 20 Reference Input Current Reference Input Capacitance l V ppm/C dB VCC /2 V 1 A pF Power Supply VCC Positive Supply Voltage For Specified Performance l ICC Supply Current (Note 8) VCC = 5V, Internal Reference On VCC = 5V, Internal Reference Off l l ISD Supply Current in Shutdown Mode (Note 8) VCC = 5V l 4.5 1.9 1.5 5.5 V 2.5 2 mA mA 3 A 0.3VCC V Digital I/O VIL Low Level Input Voltage (SDA and SCL) l VIH High Level Input Voltage (SDA and SCL) l VIL(LDAC) Low Level Input Voltage (LDAC) VCC = 4.5V to 5.5V l VIH(LDAC) High Level Input Voltage (LDAC) VCC = 4.5V to 5.5V l VIL(CA) Low Level Input Voltage (CA0 to CA2) See Test Circuit 1 l 0.7VCC V 0.8 2.4 V V 0.15VCC V VIH(CA) High Level Input Voltage (CA0 to CA2) See Test Circuit 1 l RINH Resistance from CAn (n = 0,1,2) to VCC to Set CAn = VCC See Test Circuit 2 l 10 k RINL Resistance from CAn (n = 0,1,2) to GND to Set CAn = GND See Test Circuit 2 l 10 k RINF Resistance from CAn (n = 0,1,2) to VCC or GND to Set CAn = FLOAT See Test Circuit 2 l VOL Low Level Output Voltage Sink Current = 3mA l 0 0.4 V tOF Output Fall Time VO = VIH(MIN) to VO = VIL(MAX), CB = 10pF to 400pF (Note 13) l 20+0.1CB 250 ns tSP Pulse Width of Spikes Suppressed by Input Filter l 0 50 ns IIN Input Leakage 0.1VCC VIN 0.9VCC l 1 A CIN I/O Pin Capacitance (Note 9) l 10 pF CB Capacitance Load for Each Bus Line l 400 pF CCAn External Capacitive Load on Address Pins CA0, CA1 and CA2 l 10 pF 0.85VCC V 2 M 2655f 8 LTC2655 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V (LTC2655B-L16/LTC2655-L12), VCC = 4.5V to 5.5V (LTC2655B-H16, LTC2655-H12), VOUT unloaded unless otherwise specified. LTC2655B-L16/LTC2655-L12/LTC2655B-H16/LTC2655-H12 SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS AC Performance ts Settling Time ( Note 10) 0.024%(1LSB at 12 Bits) 0.0015%(1LSB at 16 Bits) 3.9 9.1 s s Settling Time for 1LSB Step 0.024%(1LSB at 12 Bits) 0.0015%(1LSB at 16 Bits) 2.4 4.5 s s 1.8 V/s Voltage Output Slew Rate Capacitive Load Driving Glitch Impulse (Note 11) 1000 At Mid-Scale Transition, -L Option 4 At Mid-Scale Transition, -H Option DAC to DAC Crosstalk (Note 12) CREFCOMP = CREFIN/OUT = 0.22F Multiplying Bandwidth en pF nV*s 7 nV*s 0.5 nV*s 150 kHz Output Voltage Noise Density At f = 1kHz At f = 10kHz 85 80 nV/Hz nV/Hz Output Voltage Noise 0.1Hz to 10Hz, Internal Reference (-L Options) 0.1Hz to 10Hz, Internal Reference (-H Options) 0.1Hz to 200KHz, Internal Reference (-L Options) 0.1Hz to 200KHz, Internal Reference (-H Options) 8 12 400 450 VP-P VP-P VP-P VP-P TIMING CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 2.7V to 5.5V (LTC2655B-L16/LTC2655-L12), VCC = 4.5V to 5.5V (LTC2655B-H16, LTC2655-H12), VOUT unloaded unless otherwise specified. LTC2655B-L16/LTC2655-L12/LTC2655B-H16/LTC2655-H12 (see Figure 1) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS fSCL SCL Clock Frequency l 0 tHD(STA) Hold Time (Repeated) Start Condition l 400 kHz 0.6 s tLOW Low Period of the SCL Clock Pin l 1.3 s tHIGH High Period of the SCL Clock Pin l 0.6 s tSU(STA) Set-Up Time for a Repeated Start Program l 0.6 s tHD(DAT) Data Hold Time l 0 0.9 s tSU(DAT) Data Set-Up Time l 100 tr Rise Time of Both SDA and SCL Signals (Note 13) l 20+0.1CB 300 ns tf Fall Time of Both SDA and SCL Signals (Note 13) l 20+0.1CB 300 ns ns tSU(STO) Set-Up Time for Stop Condition l 0.6 s tBUF Bus Free Time Between a Stop and Start Condition l 1.3 s t1 Falling edge of the 9th Clock of the 3rd Input Byte to LDAC High or Low Transition l 400 ns t2 LDAC Low Pulse Width l 20 ns 2655f 9 LTC2655 ELECTRICAL CHARACTERISTICS Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltages are with respect to GND. Note 3: Linearity and monotonicity are defined from code kL to code 2N-1, where N is the resolution and kL is the lower end code for which no output limiting occurs. For VREF = 2.5V and N = 16, kL = 128 and linearity is defined from code 128 to code 65535. For VREF = 2.5V and N = 12, kL =8 and linearity is defined from code 8 to code 4095. Note 4: Inferred from measurement at code 128 (LTC2655-16), or code 8 (LTC2655-12). Note 5: DC Crosstalk is measured with VCC = 5V and using internal reference, with the measured DAC at mid-scale. Note 6: This IC includes current limiting that is intended to protect the device during momentary overload conditions. Junction temperature can exceed the rated maximum during current limiting. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 7: Temperature coefficient is calculated by dividing the maximum change in output voltage by the specified temperature range. Maximum temperature coefficient is guaranteed for C-grade only. Note 8: Digital inputs at 0V or VCC. Note 9: Guaranteed by design and not production tested. Note 10: Internal Reference mode. DAC is stepped 1/4 scale to 3/4 scale and 3/4 scale to 1/4 scale. Load is 2k in parallel with 200pF to GND. Note 11: VCC = 5V (-H Options) or VCC = 3V (-L Options), internal reference mode. DAC is stepped 1 LSB between half-scale and half-scale - 1. Load is 2k n parallel with 200pF to GND. Note 12: DAC to DAC Crosstalk is the glitch that appears at the output of one DAC due to a full scale change at the output of another DAC. It is measured with VCC = 5V and using internal reference, with the measured DAC at mid-scale. Note 13: CB = Capacitance of one bus line in pF. Note 14: Gain error specification may be degraded for reference input voltages less than 1V. See Gain Error vs Reference Input Curve in the Typical Performance Characteristics section. 2655f 10 LTC2655 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C unless otherwise noted. LTC2655-L16 Integral Nonlinearity (INL) 4 Differential Nonlinearity (DNL) 1.0 VCC = 3V VCC = 3V 3 0.5 1 DNL (LSB) INL (LSB) 2 0 -1 -2 0 -0.5 -3 -4 128 16384 32768 CODE -1.0 128 65535 49152 16384 32768 CODE 49152 2655 G01 4 2655 G02 REFIN/OUT Output Voltage vs Temperature DNL vs Temperature INL vs Temperature 1.0 VCC = 3V 1.253 VCC = 3V 3 1.252 1.251 0 -1 DNL(POS) VREF (V) 1 -2 VCC = 3V 0.5 INL(POS) DNL (LSB) INL (LSB) 2 65535 0 DNL(NEG) 1.250 1.249 INL(NEG) -0.5 1.248 -3 -4 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) -1.0 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G04 2655 G03 Settling to 1LSB Rising SCL 3V/DIV 1.247 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G05 Settling to 1LSB Falling 9TH CLOCK OF 3RD DATA BYTE VOUT 200V/DIV 1/4 SCALE TO 3/4 SCALE STEP VCC = 3V, VFS = 2.50V VOUT 250V/DIV 7.3s 3/4 SCALE TO 1/4 SCALE STEP VCC = 3V, VFS = 2.50V RL = 2k, CL = 200pF AVERAGE OF 2048 EVENTS 7.8s SCL 3V/DIV 9TH CLOCK OF 3RD DATA BYTE 2655 G06 2s/DIV 2655 G07 2s/DIV 2655f 11 LTC2655 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C unless otherwise noted. LTC2655-H16 Integral Nonlinearity (INL) 4 Differential Nonlinearity (DNL) 1.0 VCC = 5V VCC = 5V 3 0.5 1 DNL (LSB) INL (LSB) 2 0 -1 -2 0 -0.5 -3 -4 128 16384 32768 CODE -1.0 128 65535 49152 16384 32768 CODE 49152 2655 G08 INL vs Temperature 4 2655 G09 Reference Output Voltage vs Temperature DNL vs Temperature 1.0 VCC = 3V 2.054 VCC = 3V 3 0.5 2.050 0 -1 DNL(POS) VREF (V) 1 -2 VCC = 5V 2.052 INL(POS) DNL (LSB) INL (LSB) 2 65535 0 DNL(NEG) 2.048 2.046 -0.5 INL(NEG) 2.044 -3 -4 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) -1.0 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G11 2655 G10 Settling to 1LSB Rising SCL 5V/DIV 2.042 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G12 Settling to 1LSB Falling 9TH CLOCK OF 3RD DATA BYTE 1/4 SCALE TO 3/4 SCALE STEP VCC = 5V, VFS = 4.096V RL = 2k, CL = 200pF VOUT 250V/DIV 3/4 SCALE TO 1/4 SCALE STEP VCC = 5V, VFS = 4.096V RL = 2k, CL = 200pF 7.9s VOUT 250V/DIV 5.5s SCL 5V/DIV 9TH CLOCK OF 3RD DATA BYTE 2655 G14 2655 G13 2s/DIV 2s/DIV 2655f 12 LTC2655 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C unless otherwise noted. LTC2655-12 1.0 VCC = 5V VREF = 2.048V DNL (LSB) INL (LSB) VCC = 3V VREF = 1.25V SCL 3V/DIV 0.5 0.5 0 4.0s 0 VOUT 1mV/DIV -0.5 -0.5 -1.0 Settling to 1LSB Falling Differential Nonlinearity (INL) Integral Nonlinearity (INL) 1.0 -1.0 8 1024 2048 CODE 3072 4095 3/4 TO 1/4 SCALE STEP VCC = 3V, VFS = 2.5V RL = 2k, CL = 200pF AVERAGE OF 2048 EVENTS 8 1024 2048 CODE 3072 2655 G17 4095 2s/DIV 2655 G16 2655 G15 LTC2655 Load Regulation Headroom at Rails vs Output Current Current Limiting 10 5.0 0.20 INTERNAL REF 8 CODE = MID-SCALE INTERNAL REF 0.15 CODE = MID-SCALE 4.5 5V (LTC2655-H) SOURCING 6 4.0 0.10 0 -2 3.5 0.05 VOUT (V) 2 VOUT (V) $VOUT (mV) 4 0 -0.05 -4 2.5 2.0 1.5 -0.10 -6 VCC = 5V (LTC2655-H) -8 VCC = 3V (LTC2655-L) -10 -50 -40 -30 -20 -10 0 10 20 30 40 50 IOUT (mA) 2655 G18 VCC = 5V (LTC2655-H) VCC = 3V (LTC2655-L) -0.20 -50 -40 -30 -20 -10 0 10 20 30 40 50 IOUT (mA) 0.5 3V (LTC2655-L) SINKING 0 Zero-Scale Error vs Temperature 2 2655 G21 4 5 6 IOUT (mA) 7 8 9 10 LTC2655-16 32 2.0 1.5 1.0 16 0 -16 -32 0.5 -3 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 3 48 GAIN ERROR (LSB) ZERO-SCALE ERROR (mV) -2 2 Gain Error vs Temperature 64 2.5 -1 1 2655 G20 3.0 0 0 2655 G19 Offset Error vs Temperature 1 5V (LTC2655-H) SINKING 1.0 -0.15 3 OFFSET ERROR (mV) 3V (LTC2655-L) SOURCING 3.0 -48 0 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G22 -64 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G23 2655f 13 LTC2655 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C unless otherwise noted. LTC2655 Gain Error vs Reference Input Offset Error vs Reference Input LTC2655-16 48 VCC = 5.5V GAIN ERROR OF 4 CHANNELS 1.0 32 0.5 0 -0.5 350 300 0 -16 -32 -1.5 -48 50 1 1.5 2 REFERENCE VOLTAGE (V) 4.5 5.5 5 ICC Shutdown vs Temperature VCC = 5V (LTC2655-H) 2.0 VCC = 3V (LTC2655-L) 2.5 2.0 1.5 1.6 2 3 LOGIC VOLTAGE (V) 4 5 LTC2655-H VCC = 5V, CODE = MS INTERNAL REFERENCE LTC2655-L VCC = 3V, CODE = MS INTERNAL REFERENCE 1.0 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) ICC SHUTDOWN (A) SUPPLY CURRENT (mA) ICC (mA) 4 VCC (V) 4 2.2 3 LTC2655-H VCC = 5V 2 1 LTC2655-L VCC = 3V 0 -50 -30 -10 10 30 50 70 90 110 130 TEMPERATURE (C) 2655 G29 2655 G28 2655 G27 Multiplying Bandwidth Large-Signal Response 8 Mid-Scale Glitch Impulse VCC = 5V, VREF = 2.048V ZERO-SCALE TO FULL-SCALE 6 SCL 5V/DIV 4 AMPLITUDE (dB) 3.5 5 3.0 SWEEP SCL AND SDA BETWEEN 2.4 0V AND VCC 3 2655 G26 Supply Current vs Temperature Supply Current vs Logic Voltage 1 0 2.5 2.5 2655 G25 2.6 0 200 100 2655 G24 1.8 250 150 -64 0.5 2.5 1 1.5 2 REFERENCE VOLTAGE (V) 400 16 -1.0 -2 0.5 450 ICC (nA) GAIN ERROR (LSB) OFFSET ERROR (mV) VCC = 5V 1.5 OFFSET ERROR OF 4 CHANNELS 1.4 ICC Shutdown vs VCC 64 2.0 9TH CLOCK OF 3RD DATA BYTE 2 0 VOUT 5mV/DIV VOUT 1V/DIV -2 LTC2655-H16, VCC = 5V 7nV-s TYP -4 -6 -10 -12 LTC2655-L16, VCC = 3V 4nV-s TYP VS = 5V VREF(DC) = 2V VREF(AC) = 0.2VP-P CODE = FULL-SCALE -8 1k 10k 100k FREQUENCY (Hz) 1M 2655 G32 2655 G31 2s/DIV 2s/DIV 2655 G30 2655f 14 LTC2655 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C unless otherwise noted. LTC2655 DAC to DAC Crosstalk (Dynamic) ONE DAC SWITCH 0-FS 1V/DIV Power-On Reset Glitch VCC 2V/DIV ZERO-SCALE VOUT 10mV/DIV VOUT 0.5mV/DIV LTC2655-L16, VCC = 5V, 0.4nV*s TYP CREFCOMP = CREFOUT = 0.22F 2655 G34 2655 G33 200s/DIV 2s/DIV Power-On Reset to Mid-Scale Noise Voltage vs Frequency 400 NOISE VOLTAGE (nV/Hz) LTC2655-L VCC 2V/DIV VOUT 1V/DIV 2655 G35 300 VCC = 5V CODE = MID-SCALE INTERNAL REF CREFCOMP = CREFOUT = 0.1F 200 LTC2655-H 100 0 1ms/DIV LTC2655-L 10 100 1k 10k FREQUENCY (Hz) 100k 1M 2655 G36 DAC Output 0.1Hz to 10Hz Voltage Noise Reference 0.1Hz to 10Hz Voltage Noise VREFOUT = 2.048V CREFCOMP = CREFOUT = 0.1F VCC = 5V, LTC2655-H CODE = MID-SCALE INTERNAL REF CREFCOMP = CREFOUT = 0.1F 2V/DIV 5V/DIV 2655 G38 2655 G37 1s/DIV 1s/DIV 2655f 15 LTC2655 PIN FUNCTIONS (GN/UF) REFLO (Pin 1/Pin 20): Reference Low. The voltage at this pin sets the zero-scale voltage of all DACs. This pin should be tied to GND. VOUTA to VOUTD (Pins 2,4,13,14/Pins 1, 3, 13, 14): DAC Analog Voltage Outputs. The output range is 0V to 2 times the voltage at the REFIN/OUT pin. REFCOMP (Pin 3/Pin 2): Internal Reference Compensation. For low noise and reference stability, tie 0.1F capacitor to GND. Connect to GND to use an external reference at start-up. Command 0111b must still be issued to turn off internal reference. REFIN/OUT (Pin 5/Pin 4): This pin acts as the internal reference output in internal reference mode and acts as the reference input pin in external reference mode. When acting as an output the nominal voltage at this pin is 1.25V for -L options and 2.048V for -H options. For low noise and reference stability tie a capacitor from this pin to GND. Capacitor value must be CREFCOMP. In external reference mode, the allowable reference input voltage range is 0.5V to VCC /2. LDAC (Pin 6/Pin 5): Asynchronous DAC Update. A falling edge on this input after four bytes have been written into the part, immediately updates the DAC register with the contents of the input register. A low on this input without a complete 32-bit (four bytes including the slave address) data write transfer to the part does not update the DAC output. Software power-down is disabled when LDAC is low. SCL (Pin 8/Pin 7): Serial Clock Input. Data is shifted into the SDA pin at the rising edges of the clock. This high impedance pin requires a pull-up resistor or current source to VCC. SDA (Pin 9/Pin 9): Serial Data Bidirectional. Data is shifted into the SDA pin and acknowledged by the SDA pin. This is a high impedance pin while data is shifted in. It is an opendrain N-channel output during acknowledgement. This pin requires a pull-up resistor or current source to VCC. CA1 (Pin 10/Pin 10): Chip Address Bit 1. Tie this pin to VCC, GND or leave it floating to select an I2C slave address for the part (Table 2). CA0 (Pin 11/Pin 11): Chip Address Bit 0. Tie this pin to VCC, GND or leave it floating to select an I2C slave address for the part (Table 2). PORSEL (Pin 12/Pin 12): Power-On-Reset Select. If tied to GND, the part resets to zero-scale at power-up, if tied to VCC, the part resets to mid-scale. VCC (Pin 15/Pin 18): Supply Voltage Input. For -L options, 2.7V VCC 5.5V, and for -H options, 4.5V VCC 5.5V. Bypass to ground with a 0.1F capacitor placed as close to pin as possible. GND (Pin 16/Pin 19, Exposed Pad Pin 21): Ground. Must be soldered to PCB Ground. DNC (NA/Pins 8, 15, 16, 17): Do not connect these pins. CA2 (Pin 7/Pin 6): Chip Address Bit 2. Tie this pin to VCC, GND or leave it floating to select an I2C slave address for the part (Table 2). 2655f 16 LTC2655 BLOCK DIAGRAM REFCOMP REFIN/OUT INTERNAL REFERENCE GND VCC REGISTER REGISTER REGISTER DAC B REGISTER REGISTER CA0 DAC D REGISTER VOUTB DAC A REGISTER VOUTA REGISTER REFLO DAC C CA1 32-BIT SHIFT REGISTER CA2 SCL POWER-ON RESET VOUTD VOUTC PORSEL SDA 2-WIRE INTERFACE LDAC 2655 BD 2655f 17 LTC2655 TEST CIRCUITS Test Circuit 1 100 CAn VIH(CAn)/VIL(CAn) 2655 TC01 Test Circuit 2 VDD RINH/RINL/RINF 2655 TC02 GND TIMING DIAGRAM SDA tf tLOW tSU(DAT) tr tf tHD(STA) tSP tr tBUF SCL S tHD(STA) tHD(DAT) tHIGH tSU(STA) S tSU(STO) P S 2655 F01 ALL VOLTAGE LEVELS REFER TO VIH(MIN) AND VIL(MAX) LEVELS 9TH CLOCK OF 3RD DATA BYTE SCL t1 LDAC Figure 1 2655f 18 LTC2655 OPERATION The LTC2655 is a family of quad voltage output DACs in 20-lead 4mm x 4mm QFN and in 16-lead narrow SSOP packages. Each DAC can operate rail-to-rail in external reference mode, or with its full-scale voltage set by an integrated reference. Four combinations of accuracy (16-bit and 12-bit), and full-scale voltage (2.5V or 4.096V) are available. The LTC2655 is controlled using a 2-wire I2C compatible interface. Power-On Reset The LTC2655-L/LTC2655-H clear the output to zero-scale if PORSEL pin is tied to GND, when power is first applied, making system initialization consistent and repeatable. For some applications, downstream circuits are active during DAC power-up, and may be sensitive to nonzero outputs from the DAC during this time. The LTC2655 contains circuitry to reduce the power-on glitch. The analog outputs typically rise less than 10mV above zero-scale during power on if the power supply is ramped to 5V in 1ms or more. In general, the glitch amplitude decreases as the power supply ramp time is increased. See Power-On Reset Glitch in the Typical Performance Characteristics section. Alternatively, if PORSEL pin is tied to VCC, The LTC2655-L/ LTC2655-H set the output to mid-scale when power is first applied. Power Supply Sequencing and Start-Up For the LTC2655 family of parts, the internal reference is powered up at start-up by default. If an external reference is to be used, REFCOMP (Pin 3/Pin 2, GN/UF) must be hardwired to GND. This configuration allows the use of an external reference at start-up and converts the REFIN/OUT pin to an input. However, the internal reference will still be ON and draw supply current. In order to use an external reference, command 0111b should be used to turn the internal reference off (see Table 1). The voltage at REFIN/OUT (Pin 5/Pin 4, GN/UF) should be kept within the range - 0.3V REFIN/OUT VCC + 0.3V (see the Absolute Maximum Ratings section). Particular care should be taken to observe these limits during power supply turn-on and turn-off sequences, when the voltage at VCC (Pin 15/Pin 18, GN/UF) is in transition. Transfer Function The digital-to-analog transfer function is VOUT(IDEAL) = 2 * k/2N [VREF - REFLO] + REFLO where k is the decimal equivalent of the binary DAC input code, N is the resolution, and VREF is the voltage at the REFIN/OUT Pin. The resulting DAC output span is 0V to 2*VREF, as it is necessary to tie REFLO to GND. VREF is nominally 1.25V for LTC2655-L and 2.048V for LTC2655-H, in internal reference mode. Table 1 COMMAND* C3 C2 C1 C0 0 0 0 0 Write to Input Register n 0 0 0 1 Update (Power-Up) DAC Register n 0 0 1 0 Write to Input Register n, Update (Power-Up) All 0 0 1 1 Write to and Update (Power-Up) n 0 1 0 0 Power-Down n 0 1 0 1 Power-Down Chip (All DAC's and Reference) 0 1 1 0 Select Internal Reference (Power-Up Reference) 0 1 1 1 Select External Reference (Power-Down Reference) 1 1 1 1 No Operation ADDRESS (n)* A3 A2 A1 A0 0 0 0 0 DAC A 0 0 0 1 DAC B 0 0 1 0 DAC C 0 0 1 1 DAC D 1 1 1 1 All DACs * Command and address codes not shown are reserved and should not be used. Serial Interface The LTC2655 communicates with a host using the standard 2-wire I2C interface. The Timing Diagram (Figure 1) shows the timing relationship of the signals on the bus. The two bus lines, SDA and SCL, must be high when the bus is not in use. External pull-up resistors or current sources are required on these lines. The value of these pull-up resistors is dependent on the power supply and can be obtained from the I2C specifications. For an I2C bus operating in the fast mode, an active pull-up will be 2655f 19 LTC2655 OPERATION necessary if the bus capacitance is greater than 200pF. The LTC2655 is a receive-only (slave) device. The master can write to the LTC2655. The LTC2655 does not respond to a read command from the master. The START (S) and STOP (P) Conditions When the bus is not in use, both SCL and SDA must be high. A bus master signals the beginning of a communication to a slave device by transmitting a START condition (see Figure 1). A START condition is generated by transitioning SDA from high to low while SCL is high. When the master has finished communicating with the slave, it issues a STOP condition. A STOP condition is generated by transitioning SDA from low to high while SCL is high. The bus is then free for communication with another I2C device. Acknowledge The Acknowledge signal is used for handshaking between the master and the slave. An Acknowledge (active LOW) generated by the slave lets the master know that the latest byte of information was received. The Acknowledge related clock pulse is generated by the master. The master releases the SDA line (HIGH) during the Acknowledge clock pulse. The slave-receiver must pull down the SDA bus line during the Acknowledge clock pulse so that it remains a stable LOW during the HIGH period of this clock pulse. The LTC2655 responds to a write by a master in this manner. The LTC2655 does not acknowledge a read (retains SDA HIGH during the period of the Acknowledge clock pulse). Chip Address The state of CA0, CA1 and CA2 decides the slave address of the part. The pins CA0, CA1 and CA2 can be each set to any one of three states: VCC , GND or float. This results in 27 selectable addresses for the part. The slave address assignments are shown in Table 2. In addition to the address selected by the address pins, the parts also respond to a global address. This address allows a common write to all LTC2655 parts to be accomplished with one 3-byte write transaction on the I2C bus. The global address is a 7-bit on-chip hardwired address and is not selectable by CA0, CA1 and CA2. The addresses corresponding to the states of CA0, CA1 and CA2 and the global address are shown in Table 2. The maximum capacitive load allowed on the address pins (CA0, CA1 and CA2) is 10pF, as these pins are driven during address detection to determine if they are floating. Table 2. Slave Address Map CA2 CA1 CA0 A6 A5 A4 A3 A2 A1 A0 GND GND GND 0 0 1 0 0 0 0 GND GND FLOAT 0 0 1 0 0 0 1 GND GND VCC 0 0 1 0 0 1 0 GND FLOAT GND 0 0 1 0 0 1 1 GND FLOAT FLOAT 0 1 0 0 0 0 0 GND FLOAT VCC 0 1 0 0 0 0 1 GND VCC GND 0 1 0 0 0 1 0 GND VCC FLOAT 0 1 0 0 0 1 1 GND VCC VCC 0 1 1 0 0 0 0 FLOAT GND GND 0 1 1 0 0 0 1 FLOAT GND FLOAT 0 1 1 0 0 1 0 FLOAT GND VCC 0 1 1 0 0 1 1 FLOAT FLOAT GND 1 0 0 0 0 0 0 FLOAT FLOAT FLOAT 1 0 0 0 0 0 1 FLOAT FLOAT VCC 1 0 0 0 0 1 0 FLOAT VCC GND 1 0 0 0 0 1 1 FLOAT VCC FLOAT 1 0 1 0 0 0 0 FLOAT VCC VCC 1 0 1 0 0 0 1 VCC GND GND 1 0 1 0 0 1 0 VCC GND FLOAT 1 0 1 0 0 1 1 VCC GND VCC 1 1 0 0 0 0 0 VCC FLOAT GND 1 1 0 0 0 0 1 VCC FLOAT FLOAT 1 1 0 0 0 1 0 VCC FLOAT VCC 1 1 0 0 0 1 1 VCC VCC GND 1 1 1 0 0 0 0 VCC VCC FLOAT 1 1 1 0 0 0 1 VCC VCC VCC GLOBAL ADDRESS 1 1 1 0 0 1 0 1 1 1 0 0 1 1 2655f 20 LTC2655 OPERATION Write Word Protocol Power-Down Mode The master initiates communication with the LTC2655 with a START condition and a 7-bit slave address followed by the Write bit (W) = 0. The LTC2655 acknowledges by pulling the SDA pin low at the 9th clock if the 7-bit slave address matches the address of the part (set by CA0, CA1 and CA2) or the global address. The master then transmits three bytes of write data. The LTC2655 acknowledges each byte of data by pulling the SDA line low at the 9th clock of each data byte transmission. After receiving three complete bytes of data, the LTC2655 executes the command specified in the 24-bit input word. If more than three data bytes are transmitted after a valid 7-bit slave address, the LTC2655 does not acknowledge the extra bytes of data (SDA is high during the 9th clock). The first byte of the input word consists of the 4-bit command followed by the 4-bit address. The next two bytes consist of the 16-bit data word. The 16-bit data word consists of the 16-bit, or 12-bit input code, MSB to LSB, followed by 0 or 4 don't care bits (LTC2655-16 and LTC2655-12 respectively). A typical LTC2655 write transaction is shown in Figure 2. The command (C3-C0) and address (A3-A0) assignments are shown in Table 1. The first four commands in the table consist of write and update operations. A write operation loads a 16-bit data word from the 32-bit shift register into the input register. In an update operation, the data word is copied from the input register to the DAC register and converted to an analog voltage at the DAC output. The update operation also powers up the DAC if it had been in power-down mode. The data path and registers are shown in the Block Diagram. For power-constrained applications, power-down mode can be used to reduce the supply current whenever less than four outputs are needed. When in power-down, the buffer amplifiers, bias circuits and integrated reference circuits are disabled, and draw essentially zero current. The DAC outputs are put into a high-impedance state, and the output pins are passively pulled to ground through individual 80k resistors. Input- and DAC-register contents are not disturbed during power-down. Any channel or combination of channels can be put into power-down mode by using command 0100b in combination with the appropriate DAC address, (n). The integrated reference is automatically powered down when external reference mode is selected using command 0111b. In addition, all the DAC channels and the integrated reference together can be put into power-down mode using the Power-Down Chip command 0101b. For all power-down commands the 16-bit data word is ignored, but still required in order to complete a full communication cycle. Normal operation resumes by executing any command which includes a DAC update, in software as shown in Table 1 or using the asynchronous LDAC pin. The selected DAC is powered up as its voltage output is updated. When a DAC which is in a powered-down state is powered up and updated, normal settling is delayed. If less than four DACs are in a powered-down state prior to the update command, the power-up delay time is approximately 12s. If on the other hand, all four DACs and the integrated reference are powered down, then the main bias generation circuit block has been automatically shut down in addition to the individual DAC amplifiers and the integrated reference. 2655f 21 LTC2655 OPERATION In this case, the power-up delay time is approximately 14s. The power-up of the integrated reference depends on the command that powered it down. If the reference is powered down using the Select External Reference command (0111b), then it can only be powered back up by sending the Select Internal Reference command (0110b). However if the reference was powered down by sending the Power-Down Chip command (0101b), then in addition to the Select Internal Reference command (0110b), any command that powers up the DACs will also power-up the integrated reference. Reference Modes For applications where an accurate external reference is not available, the LTC2655 has a user-selectable, integrated reference. The LTC2655-L has a 1.25V reference that provides a full-scale output of 2.5V. The LTC2655-H has a 2.048V reference that provides a full-scale output of 4.096V. Both references exhibit a typical temperature drift of 2ppm/C. Internal reference mode can be selected by using command 0110b, and is the power-on default. A buffer is needed if the internal reference is required to drive external circuitry. For reference stability and low noise, it is recommended that a 0.1F capacitor be tied between REFCOMP and GND. In this configuration, the internal reference can drive up to 0.1F capacitive load without any stability problems. In order to ensure stable operation, the capacitive load on the REFIN/OUT pin should not exceed the capacitive load on the REFCOMP pin. The DAC can also operate in external reference mode using command 0111b. In this mode, the REFIN/OUT pin acts as an input that sets the DAC's reference voltage. This input is high impedance and does not load the external reference source. The acceptable voltage range at this pin is 0.5V REFIN/OUT VCC /2. The resulting full-scale output voltage is 2*VREFIN/OUT. For using external reference at start-up, see the Power Supply Sequencing and Start-Up Sections. Integrated Reference Buffers Each of the four DACs in LTC2655 has its own integrated high performance reference buffer. The buffers have very high input impedance and do not load the reference voltage source. These buffers shield the reference voltage from glitches caused by DAC switching and thus minimize DAC-to-DAC dynamic crosstalk. By tying 0.22F capacitors between REFCOMP and GND, and also between REFIN/OUT and GND, the crosstalk can be reduced to less than 1nV*s. See the curve DAC-to-DAC Crosstalk (Dynamic) in the Typical Performance Characteristics section. Voltage Outputs Each of the four rail-to-rail amplifiers contained in LTC2655 has guaranteed load regulation when sourcing or sinking up to 15mA at 5V (7.5mA at 3V). Load regulation is a measure of the amplifier's ability to maintain the rated voltage accuracy over a wide range of load conditions. The measured change in output voltage per milliampere of forced load current change is expressed in LSB/mA. DC output impedance is equivalent to load regulation, and may be derived from it by simply calculating a change in units from LSB/mA to ohms. The amplifiers' DC output impedance is 0.040 when driving a load well away from the rails. When drawing a load current from either rail, the output voltage headroom with respect to that rail is limited by the 30 typical channel resistance of the output devices; e.g., when sinking 1mA, the minimum output voltage = 30 * 1mA = 30mV. See the graph Headroom at Rails vs Output Current in the Typical Performance Characteristics section. The amplifiers are stable driving capacitive loads of up to 1000pF. 2655f 22 LTC2655 OPERATION Board Layout Rail-to-Rail Output Considerations The excellent load regulation and DC crosstalk performance of these devices is achieved in part by keeping signal and power grounds separate. In any rail-to-rail voltage output device, the output is limited to voltages within the supply range. The PC board should have separate areas for the analog and digital sections of the circuit. This keeps digital signals away from sensitive analog signals and facilitates the use of separate digital and analog ground planes which have minimal capacitive and resistive interaction with each other. Digital and analog ground planes should be joined at only one point, establishing a system star ground as close to the device's ground pin as possible. Ideally, the analog ground plane should be located on the component side of the board, and should be allowed to run under the part to shield it from noise. Analog ground should be a continuous and uninterrupted plane, except for necessary lead pads and vias, with signal traces on another layer. Since the analog outputs of the device cannot go below ground, they may limit for the lowest codes as shown in Figure 3b. Similarly, limiting can occur in external reference mode near full scale when the REFIN/OUT pin is at VCC/2. If VREFIN/OUT = VCC /2 and the DAC full-scale error (FSE) is positive, the output for the highest codes limits at VCC as shown in Figure 3c. No full-scale limiting can occur if VREFIN/OUT (VCC - FSE)/2. Offset and linearity are defined and tested over the region of the DAC transfer function where no output limiting can occur. The GND pin functions as a return path for power supply currents in the device and should be connected to analog ground. The REFLO pin should be connected to system star ground. Resistance from the REFLO pin to system star ground should be as low as possible. 2655f 23 24 2 1 SCL VOUT SA5 SA6 SA5 3 SA4 4 SA3 SA3 5 SA2 SA2 6 SA1 SA1 SLAVE ADDRESS SA4 7 SA0 SA0 8 WR 1 C3 2 C2 C2 3 C1 C1 4 C0 C0 5 A3 A3 COMMAND 6 A2 A2 7 A1 A1 8 A0 A0 9 ACK 1 D15 2 D14 3 D13 4 5 D11 MS DATA D12 6 D10 7 D9 8 D8 9 ACK 1 D7 2 D6 Figure 2. Typical LTC2655 Input Waveform--Programming DAC Output for Full-Scale 9 ACK C3 3 D5 4 5 D3 LS DATA D4 6 D2 7 D1 8 D0 9 ACK 2655 F02 ZERO-SCALE VOLTAGE FULL-SCALE VOLTAGE STOP OPERATION SDA START SA6 LTC2655 2655f LTC2655 OPERATION POSITIVE FSE VREF = VCC VREF = VCC OUTPUT VOLTAGE OUTPUT VOLTAGE INPUT CODE (c) OUTPUT VOLTAGE 0 65, 535 (a) 0V NEGATIVE OFFSET 32, 768 INPUT CODE INPUT CODE (b) 2655 F03 Figure 3. Effects of Rail-to-Rail Operation On a DAC Transfer Curve. (a) Overall Transfer Function, (b) Effect of Negative Offset for Codes Near Zero-Scale, (c) Effect of Positive Full-Scale Error for Codes Near Full-Scale 2655f 25 LTC2655 PACKAGE DESCRIPTION GN Package 16-Lead Plastic SSOP (Reference LTC DWG # 05-08-1641) .189 - .196* (4.801 - 4.978) .045 .005 16 15 14 13 12 11 10 9 .254 MIN .009 (0.229) REF .150 - .165 .229 - .244 (5.817 - 6.198) .0165 .0015 .150 - .157** (3.810 - 3.988) .0250 BSC RECOMMENDED SOLDER PAD LAYOUT 1 .015 .004 x 45 (0.38 0.10) .007 - .0098 (0.178 - 0.249) .0532 - .0688 (1.35 - 1.75) 2 3 4 5 6 7 8 .004 - .0098 (0.102 - 0.249) 0 - 8 TYP .016 - .050 (0.406 - 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 - .012 (0.203 - 0.305) TYP .0250 (0.635) BSC GN16 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 2655f 26 LTC2655 PACKAGE DESCRIPTION UF Package 20-Lead (4mm x 4mm) Plastic QFN (Reference LTC DWG # 05-08-1710 Rev A) 0.70 0.05 4.50 0.05 3.10 0.05 2.00 REF 2.45 0.05 2.45 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 0.10 0.75 0.05 R = 0.05 TYP R = 0.115 TYP 19 20 0.40 0.10 PIN 1 TOP MARK (NOTE 6) 4.00 0.10 PIN 1 NOTCH R = 0.20 TYP OR 0.35 x 45 CHAMFER BOTTOM VIEW--EXPOSED PAD 1 2.00 REF 2.45 0.10 2 2.45 0.10 (UF20) QFN 01-07 REV A 0.200 REF 0.00 - 0.05 0.25 0.05 0.50 BSC NOTE: 1. DRAWING IS PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-1)--TO BE APPROVED 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 2655f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 27 LTC2655 TYPICAL APPLICATION 5V Bipolar Output DAC +5V C2 0.1F 3 C1 +5V 0.1F C3 0.1F + 5 1 +12V LTC6240IS5 4 - 7 2 LT1991 8 5 TO MICROCONTROLLER 7 9 11 10 6 18 2 4 LDAC VCC REFCOMP REFIN/OUT SCL SDA CA0 LTC2655IUF-L16* CA1 CA2 GND GND REFLO PORSEL 19 21 20 12 17 16 DNC DNC VOUTA VOUTB VOUTC VOUTD 9 1 10 3 50k 450k 150k 4pF M9 M3 450k M1 13 1 14 2 DNC DNC 8 VCC 15 3 5V - + 6 VOUT 5V 450k 450k P1 4pF 150k P3 50k VEE REF P9 2655 TA02 4 *PIN NUMBERS SHOWN ARE FOR THE QFN PACKAGE. 5 -12V RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC2609/LTC2619/ Quad 16-/14-/12-Bit I2C VOUT DACs LTC2629 250A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output with Separate VREF Pins for Each DAC, SSOP-16 Package LTC2605/LTC2615/ Octal 16-/14-/12-Bit I2C VOUT DACs LTC2625 250A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output, SSOP-16 Package LTC2607/LTC2617/ Dual 16-/14-/12-Bit I2C VOUT DACs LTC2627 260A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output, 3mm x 4mm DFN-12 Package LTC2606/LTC2616/ Single 16-/14-/12-Bit I2C VOUT DACs LTC2626 270A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output, 3mm x 3mm DFN-10 Package LTC2654 Quad 16-/12-Bit SPI VOUT DACs with 10ppm/C (Max) Reference 4LSB INL, 1LSB DNL, 4mm x 4mm QFN-20, Narrow SSOP-16 Packages LTC2656/LTC2657 Octal 16-/12-Bit SPI/I2C VOUT DACs with 10ppm/C (Max) Reference 4LSB INL, 1LSB DNL, 4mm x 5mm QFN-20, TSSOP-20 Packages LTC2634/LTC2635 Quad 12-/10-/8-Bit SPI/I2C VOUT DACs with 10ppm/C (Typ) Reference 125A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output, 3mm x 3mm QFN-16 and MSOP-10 Packages LTC2636/LTC2637 Octal 12-/10-/8-Bit SPI/I2C VOUT DACs with 10ppm/C (Typ) Reference 125A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output, 4mm x 3mm DFN-14 and MSOP-16 Packages LTC2630/LTC2631 Single 12-/10-/8-Bit SPI/I2C VOUT DACs with Bidirectional 10ppm/C (Typ) Reference 180A per DAC, 2.7V to 5.5V Supply Range, Rail-to-Rail Output, 6-Lead SC70 Package (LTC2630), 8-Lead TSOT-23 (LTC2631) LTC2641/LTC2642 Single 16-/14-/12-Bit SPI VOUT DACs with 1LSB INL, DNL 1LSB (Max) INL, DNL, 120A, 3mm x 3mm DFN and MSOP Packages LTC1669 10-Bit I2C Interface VOUT Micropower DAC 60A, 0.75 LSB DNL, Rail-to-Rail, 5-Lead SOT-23 and MSOP-8 Packages LTC6240 Single 18MHz, CMOS Op Amp Low Noise, Rail-to-Rail LT1991 Precision Gain Selectable Difference Amplifier 100A Micropower, Pin Selectable Gain = -13 to 14 2655f 28 Linear Technology Corporation LT 0710 * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2010