HMC381LP6 / 381LP6E v04.1007 Typical Applications Features The HMC381LP6 / HMC381LP6E is ideal for Wireless Infrastructure Applications: Input IP3: +27 dBm * GSM, GPRS & EDGE Conversion Gain: 9 dB * CDMA & W-CDMA Noise Figure: 12 dB * PHS & PDC Single Positive Supply: +5V @ 260 mA Low Single Input LO Drive: 0 dBm TE * WiMAX Functional Diagram General Description B SO LE The HMC381LP6 & HMC381LP6E are high linearity Dual Down Converter Receiver ICs that operate from 1.7 - 2.7 GHz and deliver a +27 dBm input third order intercept point for UMTS, PHS and WiMAX applications. The passive mixer outputs and high dynamic range IF amplifier inputs are positioned so that an external IF filter can be placed in series between them. The converter provides a gain of 9 dB and 12 dB typical single side band noise figure. The IC operates from a positive +5V rail consuming 260 mA of current while requiring a LO drive level of only -4 to +4 dBm. The design requires no external baluns and supports IF frequencies between 50 and 300 MHz. Electrical Specifi cations, TA = +25 C, LO = 0 dBm, Vdd = 5V Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units Frequency Range, RF 1.7 - 2.0 2.0 - 2.2 2.5 - 2.7 Frequency Range, LO 1.4 - 2.3 1.7 - 2.5 2.2 - 2.6 GHz Frequency Range, IF 50 - 300 [1] 50 - 300 [1] 50 - 300 [2] MHz 9 dB O MIXERS - DOWNCONVERTERS - SMT 8 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Conversion Gain 6.5 8.5 7 9 Noise Figure (SSB) 12 12.5 LO to RF Isolation 11 11 7 GHz dB 5 dB 18 dB LO to IF Isolation 16 20 14 18 13 RF to IF Isolation 30 40 40 46 32 37 dB IP3 (Input) 23 26 24 27 23 26 dBm 12 10 dBm 52 50 1 dB Compression (Input) 12 Branch Isolation 50 LO Drive Input Level (Typical) Supply Current (Idd for LO & IF) (IF bias resistor= 4.7 Ohms) dB -4 to +4 260 330 260 dBm 330 260 330 mA [1] Unless otherwise noted all measurements with low side LO & IF = 250 MHz. [2] Unless otherwise noted all measurements with low side LO & IF = 156 MHz. 8 - 70 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Isolation @ LO = 0 dBm 0 12 -10 ISOLATION (dB) 10 8 6 0 -60 1.8 2 2.2 RF FREQUENCY (GHz) 10 4 2 0 1.6 1.4 1.6 1.8 2 2.2 FREQUENCY (GHz) 2.4 2.6 Return Loss @ LO = 0 dBm 0 12 6 2.6 B SO CONVERSION GAIN (dB) 14 2.4 LE 1.6 Conversion Gain vs. LO Drive 8 -40 -50 2 1.4 RF TO IF LO TO RF LO TO IF -30 TE + 25C + 85C - 40C 4 8 -20 LO = -4 dBm LO = -2 dBm LO = 0 dBm LO = 2 dBm LO = 4 dBm 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 RF LO -5 -10 -15 -20 2.4 1.4 1.6 1.8 2 2.2 2.4 RF FREQUENCY (GHz) 2.6 2.8 IF Bandwidth @ LO = -5 dBm O P1dB vs. Temperature @ LO = 0 dBm 25 MIXERS - DOWNCONVERTERS - SMT 14 RETURN LOSS (dB) CONVERSION GAIN (dB) Conversion Gain vs. Temperature @ LO = 0 dBm 14 OUTPUT P1dB 10 15 RESPONSE (dB) P1dB (dBm) 20 INPUT P1dB 10 IINPUT P1dB, +25C OUTPUT P1dB, +25C INPUT P1dB, +85C OUTPUT P1dB, +85C INPUT P1dB, -40C OUTPUT P1dB, -40C 5 2 CONVERSION GAIN RETURN LOSS -2 -6 -10 0 1.6 6 -14 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 2.4 50 150 250 350 450 IF FREQUENCY (MHz) 550 650 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 8 - 71 HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Input and Output IP3 vs. Temperature @ LO = 0 dBm Input and Output IP3 vs LO Drive 40 40 OIP3 OIP3 35 IIP3 IP3 (dBm) 25 IIP3, +25C OIP3, +25C IIP3, +85C OIP3, +85C IIP3, -40C OIP3, -40C 20 15 IIP3 25 IIP3, -2 dBm OIP3, -2 dBm IIP3, 0 dBm OIP3, 0 dBm IIP3, +2 dBm OIP3, +2 dBm 20 10 15 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 Input and Output IP2 vs. LO Drive 1.6 2.4 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 2.4 LE 1.6 30 TE IP3 (dBm) 30 Noise Figure vs. IF Frequency 15 60 30 B SO IP2 (dBm) 40 IIP2, -2dBm OIP2, -2dBm IIP2, 0dBm OIP2, 0dBm IIP2, +2dBm OIP2, +2dBm 20 10 0 1.6 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 13 12 11 10 9 7 6 5 50 -10 -10 BRANCH ISOLATION (dB) 0 -30 LO = -4 dBm LO = -2 dBm LO = 0 dBm LO =+2 dBm LO =+4 dBm -40 -50 150 200 250 300 IF FREQUENCY (MHz) 350 400 -20 -30 -40 -50 -60 1.6 100 Branch Isolation RF1 - IF2 LO = 0 dBm, IF = 156 MHz 0 -20 LO=1.7GHz LO=1.8GHz LO=1.9GHz LO=2.0GHz LO=2.1GHz LO=2.2GHz 8 2.4 Branch Isolation RF1 - IF2 vs. LO Drive IF = 250 MHz O NOISE FIGURE (dB) 14 50 BRANCH ISOLATION (dB) MIXERS - DOWNCONVERTERS - SMT 8 35 -60 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 2.4 2 2.1 2.2 2.3 2.4 2.5 2.6 RF FREQUENCY (GHz) 2.7 2.8 Reference to output of standard path 8 - 72 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Isolation @ LO = 0 dBm, IF = 156 MHz 0 12 -10 10 8 RF TO IF LO TO RF LO TO IF -30 -40 TE 6 8 -20 4 -50 2 0 -60 2.1 2.2 2.3 2.4 2.5 2.6 RF FREQUENCY (GHz) 2.7 2.8 2 2.1 2.2 2.3 2.4 2.5 FREQUENCY (GHz) 2.6 2.7 2.8 LE 2 Input IP3 & Input P1dB @ LO = 0 dBm, IF = 156 MHz 30 20 B SO IP3 (dBm), P1dB (dBm) 25 15 10 INPUT IP3 OUTPUT P1dB INPUT P1dB 5 0 2 2.1 2.2 O MxN Spurious @ IF Port mRF 2.3 2.4 2.5 2.6 RF FREQUENCY (GHz) 2.7 2.8 Harmonics of LO nLO MIXERS - DOWNCONVERTERS - SMT 14 ISOLATION (dB) CONVERSION GAIN (dB) Conversion Gain @ LO = 0 dBm IF = 156 MHz nLO Spur @ RF Port 0 1 2 3 4 LO Freq. (GHz) 1 2 0 xx 21 52 40 1 54 0 57 82 2 95 79 53 84 94 3 94 94 95 72 95 4 94 95 94 95 95 48 1.4 8 12 15 19 88 1.5 9 13 16 21 1.6 11 14 17 24 1.7 13 15 18 29 1.8 12 13 19 29 1.9 11 12 19 28 RF Freq. = 1.9 GHz @ -10 dBm LO Freq. = 1.65 GHz @ 0 dBm All values in dBc relative to the IF power level. 3 4 LO = 0 dBm All values in dBc below input LO level measured at RF port. For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 8 - 73 HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Typical Supply Current vs. Vdd Absolute Maximum Ratings +13 dBm Vdd (LO + IF) Idd (mA) LO Drive (Vdd= +5V) +15 dBm +4.5 190 Vdd (LO or IF) +7 Vdc +5.0 260 Channel Temperature 150C +5.5 340 Continuous Pdiss (T = 85C) (derate 25.5 mW/C above 85C) 1.64 W Thermal Resistance (junction to ground paddle) 39.6 C/W Storage Temperature -65 to +150C Operating Temperature -40 to +85C ESD Sensitivity (HBM) Class 1A TE Downconverter will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS B SO LE Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] O MIXERS - DOWNCONVERTERS - SMT 8 RF / IF Input (Vdd= +5V) 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC381LP6 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC381LP6E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H381 XXXX [2] H381 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX 8 - 74 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Pin Descriptions Description Interface Schematic 1, 7 RF1, RF2 These pins are DC coupled and matched to 50 Ohms. 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28 GND Backside of package has exposed metal ground slug that must also be connected to ground. 3 Vdd Power supply for the second stage LO amplifier. One external bypass capacitor (1,000 pF) is required. 5, 15, 19 N/C No connection. These pins may be connected to RF ground. Performance will not be affected. LE B SO 9, 27 MIX IF2, MIX IF1 IF output from the mixers. This pin is DC coupled to the mixer. A low pass filter and blocking capacitor are required between mixer IF port and IF amplifier. (See application circuit). 11, 25 AMP IF2, AMP IF1 Inputs to the IF amplifiers. A low pass filter and blocking capacitor are required between mixer IF port and IF amplifier. (See application circuit). IF2, IF1 Outputs of the IF amplifiers and bias ports for the IF amplifiers. A pull up inductor, resistor, and bypass capacitors are required. (See application circuit). 17 LO These pins are AC coupled and matched to 50 Ohms. 21 Vdd LO Bias voltage for the first stage of the LO amplifier. A pull up inductor, resistor, and bypass capacitors are required. (See application circuit). O 13, 23 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 8 MIXERS - DOWNCONVERTERS - SMT Function TE Pin Number 8 - 75 HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Evaluation PCB TE LE B SO List of Materials for Evaluation PCB 106971 [1] Item Description O MIXERS - DOWNCONVERTERS - SMT 8 J1 - J5 PCB Mount SMA RF Connector J6 - J10 DC Pins C1, C4 - C10 1000 pF Chip Capacitor, 0402 Pkg. C2, C3 7 pF Chip Capacitor, 0402 Pkg. C11, C12, C13 100 pF Chip Capacitor, 0402 Pkg. L1, L2 220 nH Chip Inductor, 0603 Pkg. L3 22 nH Chip Inductor, 0603 Pkg. L4, L5 27 nH Chip Inductor, 0603 Pkg. R1, R2 4.7 Ohm Resistor, 0603 Pkg. R3 22 Ohm Resistor, 0603 Pkg. U1 HMC381LP6 / HMC381LP6E PCB [2] 106955 Evaluation Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 8 - 76 For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. HMC381LP6 / 381LP6E v04.1007 HIGH IP3 RFIC DUAL DOWNCONVERTER, 1.7 - 2.7 GHz Application Circuit Recommended Components Values (IF = DC - 300 MHz) 1000 pF O C1, C4 - C10 C2, C3 MIXERS - DOWNCONVERTERS - SMT B SO LE TE 8 7 pF C11, C12, C13 100 pF L1, L2 220 nH L3 22 nH L4, L5 27 nH R1, R2 4.7 Ohm R3 22 Ohm Note: L4, C3 and L5, C2 form low pass fi lters. C4 and C5 are DC blocks. For price, delivery, and to placeCorporation: orders: Analog Devices, Inc., For price, delivery, and to place orders, please contact Hittite Microwave One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 20 Alpha Road, Chelmsford, MA 01824 Phone: Phone: 978-250-3343 978-250-3373 781-329-4700Fax: * Order online at www.analog.com Application Support: Phone: 1-800-ANALOG-D Order On-line at www.hittite.com Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 8 - 77