Card Edge Connectors
Catalog 1654080 Issued 7-03
Card Edge Connectors
2
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Introduction
This catalog contains
product descriptions of
AMP Card Edge Connectors.
These connectors are pre-
sented in three groups:
Solder Type Board-to-
Board, Press-fit Board-to-
Board, and Wire-to-Board
connectors.
To assist you in the selec-
tion of the appropriate con-
nector for your application,
a selection guide is provid-
ed at the beginning of each
section. See the Table of
Contents on the following
page for the exact location.
A comprehensive descrip-
tion and features of a partic-
ular printed circuit board
connector family are
provided at the beginning
of that section. Various
technical documents are
referenced in the connector
family sections and are list-
ed and described at the
rear of this catalog.
The Tyco Electronics
products presented in this
catalog are designed and
manufactured according
to the highest possible
standards of quality and
craftsmanship. They offer
optimum reliability at the
lowest possible cost.
Dimensioning:
Dimensions are in inches and millimeters
unless specified otherwise. Values in
brackets are metric equivalents.
Metric symbols used are:
m (meter)
mm (millimeter)
mm2 (square millimeter)
kg (kilogram)
C (Celsius)
N (newton)
Note: Dimensions in this catalog are for
reference purposes only. Customer
drawings are available upon request.
© Copyright 1992, 1996 and 2002 by
Tyco Electronics. All Rights Reserved.
AMP, ACTION PIN, AMP-DURAGOLD,
AMP-LEAF, AMP-O-LECTRIC,
AMP-O-MATIC, AMPOMATOR,
AMP PACE, CERTI-CRIMP, DUO-TYNE,
ECONOMATE, TELEDENSITY, and TYCO
are trademarks.
Other products, logos, and company
names mentioned herein may be trade-
marks of their respective owners.
Produced under a Quality
Management System certified
to ISO 9001
A copy of the
certificate is available
upon request
Need more information?
Call Technical Support at
the numbers listed at the
bottom of the catalog
pages.
Technical Support is staffed
with specialists well versed
in Tyco Electronics prod-
ucts. They can provide you
with:
■Technical Support
■Catalogs
■Technical Documents
■Product Samples
■Tyco Electronics
Authorized Distributor
Locations
Card Edge Connectors
3
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Table of Contents
Solder Type Board-to-Board Connectors
Introduction………………………………………………………………………………………2
Selection Guide ………………………………………………………………………………4-6
Standard Edge Series Connectors
Standard Edge .050 PCI Card Edge Connectors ………………………………………7-10
Standard Edge .050 Series Connectors ………………………………………………11-14
Standard Edge II Connectors ……………………………………………………………15-27
Cantilever Beam Dip Solder Tails Overview ……………………………………………………28
.100" [2.54] Centerline ……………………………………………………………………29-34
.125" [3.18] Centerline ……………………………………………………………………35-37
.156" [3.96] Centerline ……………………………………………………………………38-40
Modified Bellows Contact Overview ……………………………………………………………41
.100" [2.54] Centerline ……………………………………………………………………42-47
.125" [3.18] Centerline ……………………………………………………………………48-52
.156" [3.96] Centerline ……………………………………………………………………53-56
Polarization Keys ………………………………………………………………………………57
Standard Daughter Card Layout…………………………………………………………………57
Low Profile Connectors ……………………………………………………………………58-63
Twin Leaf Mother Board Connectors ………………………………………………………64-72
Rotary Cam ZIF Connectors …………………………………………………………………73-82
Linear ZIF Connectors ………………………………………………………………………83-96
Press-Fit Board-to-Board Connectors
ACTION PIN Press-Fit Contacts ……………………………………………………………97
AMP PACE Connectors …………………………………………………………………98-115
TELEDENSITY Connectors ……………………………………………………………116-118
ECONOMATE Connectors ……………………………………………………………119-126
Cantilever Beam Press-Fit Connectors Overview ……………………………………………127
.050" [1.27] High Density ………………………………………………………………128-129
.100" [2.54] Centerline …………………………………………………………………130-140
.125" [3.18] Centerline …………………………………………………………………141-144
.156" [3.96] Centerline …………………………………………………………………145-148
Application Tooling ……………………………………………………………………149-151
Wire-to-Board Connectors
Introduction …………………………………………………………………………………152
Selection Guide ………………………………………………………………………………153
Crimp Snap Twin Leaf Connectors …………………………………………………154-163
AMP-LEAF Connectors…………………………………………………………………164-172
High Current Connectors………………………………………………………………173-176
DUO-TYNE Flag Connectors …………………………………………………………177-180
Printed Circuit Board Connector Hood Assemblies ………………………………181-183
Application Tooling ……………………………………………………………………184,185
Technical Documents ……………………………………………………………………186,187
Part Number Index ………………………………………………………………………188-201
Tyco Electronics Related Product Information ………………………………………………202
Card Edge Connectors
Selection Guide, Board-to-Board Connectors
4
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
.050 [1.27] X X
.100 [2.54] X
.125 [3.18] X
.150 [3.81]
.156 [3.96]
Solder XXX
Right-Angle Solder X
Wrap-Type X
Card Extender X
Solder Eyelet
Press-Fit
Surface-Mount
Introduction
Board-to-board (mother/
daughter board) connectors
are ideally suited to back-
plane wiring or any other
application requiring the
circuit connection of one
printed circuit board to
another. Designed to
shorten manufacturing time
and reduce applied costs,
these one-step, pre-assem-
bled connectors are ready
for mounting and mass
insertion.
Many of the connectors are
available with the proven
and reliable ACTION PIN
contact. This unique con-
tact has superior electrical
and physical characteristics
that are top of the line in the
industry.
Board-to-board connectors
come in a range of contact
centerline spacings of .050
[1.27] to .156 [3.96]. A wide
range of dual position sizes
and post styles are avail-
able. One family of connec-
tors features zero insertion
force of the daughter
board, along with a choice
of actuating devices. A vari-
ety of housing and contact
materials further expands
the choice of connectors
available to meet many
application requirements.
To help in choosing a con-
nector for your application,
a Selection Guide is provid-
ed on pages 4 through 6.
Centerlines
Tail Styles
Standard Edge .050 Series
PCI Connectors
(Pages 7-10)
.610
[15.49]
.300
[7.62]
.170±.020
[4.32±0.51]
Standard Edge
.050 Series Connectors
(Pages 11-14)
.350
[8.89]
.610
[15.49]
.300
[7.62]
.170±.020
[4.32±0.51]
Standard Edge II Connectors
(.100 and .125 Centerline)
(Pages 15-27)
.155
[3.94]
.368
[9.35]
.315
[8.00]
.610
[15.49]
Card Edge Connectors
5
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Selection Guide, Board-to-Board Connectors (Continued)
Centerlines
Standard Edge II
Connectors (.150 Centerline)
(Pages 15-27)
.050 [1.27]
.0625 [1.588]
X X .100 [2.54]
X X .125 [3.18]
X.150 [3.81]
X X .156 [3.96]
Tail Styles
X X X Solder
Right-Angle Solder
Wrap-Type
Card Extender
Solder Eyelet
X X Press-Fit
Surface-Mount
Centerlines
.050 [1.27]
X X .100 [2.54]
X X X .125 [3.18]
X.150 [3.81]
X X X .156 [3.96]
Tail Styles
X X X Solder
XRight-Angle Solder
XWrap-Type
Card Extender
XSolder Eyelet
Press-Fit
Surface-Mount
Twin Leaf
Mother Board Connectors
(Pages 64-72)
.400
[10.16]
.150
[3.81]
.610
[15.49]
.235
[5.97]
.054–.070 [1.37-1.78]
.045
[1.14] .015
[0.33] .008
[.203]
.200
[.508]
.015
[0.41]
.200±.020
[5.08±0.51]
.365
[9.27]
.135±.020
[3.43±0.51]
Low Profile
Connectors
(Pages 58-63)
.125
[3.18]
.165
[4.19]
.437
[11.10]
.460
[11.68]
Cantilever Beam Connectors
Standard Housing
(Pages 28-40)
Cantilever Beam
Connectors Scoop Housing
(Pages 28-40)
Modified Bellows Connector
(Pages 41-56)
.368
[9.35]
.300
[7.62]
.054-.071
[1.37-1.80]
.200
[5.08]
.610
[15.49]
.025
[.63]
.370
[9.40] .390
[9.91]
.300
[7.62]
.610
[15.49] .705
[17.91]
.145
[3.68] .020±.010
[.51±.25] .054 to .071
[1.37 to 1.80]
.395 or .510
[10.03 or 12.95]
Card Edge Connectors
6
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
High Density Press Fit
Connector
For .093 Cards
(Pages 128-129)
.400
[10.16]
.066
[1.68]
.610
[15.49] .421
[10.69] .461
[11.71]
Selection Guide, Board-to-Board Connectors (Continued)
.050 [1.27] X
.0625 [1.588]
.100 [2.54] X X
.125 [3.18] X
.150 [3.81]
.156 [3.96] X X
Solder
Right-Angle Solder
Wrap-Type X
Card Extender
Solder Eyelet
Press-Fit XXX
Surface-Mount
Centerlines
Tail Styles
Centerlines
.050 [1.27]
.0625 [1.588]
.100 [2.54] XXX
.125 [3.18] XXX
.150 [3.81]
.156 [3.96] X
Tail Styles
Solder X X
Right-Angle Solder X
Wrap-Type X X X
Card Extender
Solder Eyelet
Press-Fit X X
Surface-Mount
Rotary Cam ZIF
Connectors
(Pages 73-82)
.440
[11.18]
.150
[3.81]
.848
[21.54]
.598
[15.19]
Linear ZIF
Connectors
(Pages 83-96)
.140
[3.56] .475 [12.07]
.450 [11.43]
.845 [21.46]
.815 [20.70]
.490 [12.45]
.460 [11.68] .370 [9.40]
.345 [8.76]
AMP PACE Connectors,
Card Scoop Housing
(Pages 98-115)
A
.234
[5.94] .645
[16.38]
.130
[3.30]
.100 x .200 = .390 [9.91]
A.125 x .125 = .420 [10.67]
.125 x .200 = .420 [10.67]
AMP PACE Connectors,
Standard Housing
(Pages 98-115)
A
.234
[5.94]
.545
[13.84]
.130
[3.30]
.100 x .100 = .380 [9.65]
.100 x .200 = .360 [9.14]
A.125 x .250 = .410 [10.41]
.156 x .200 = .360 [9.14]
ECONOMATE
Connectors
(Pages 119-126)
.181
[4.60]
.415
[10.54].545
[13.84]
7
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series PCI Card Edge Connectors
Product Facts
■High density .050 [1.27]
centerline contact spacing
■Easy mating of high circuit
count daughter boards
■Polarizing web for positive
board-to-connector
registration
■Choice of plastic pylons or
metal holddowns
Connectors that support
PCI expansion cards are
derived from those on the
MicroChannel Architecture
(MCA) bus. The MCA con-
nectors are well defined
and have proven value and
reliability.
There are four connectors
that can be used depend-
ing upon the PCI implemen-
tation. The differences
between these connectors
are 32 bit and 64 bit, and
the 5 volt and 3.3 volt sig-
naling environments. PCI-X
is a version of PCI at 133
MHz which is under devel-
opment and employs stan-
dard PCI connectors. PCI-X
is limited to 1 slot versus 4
slots of PCI.
A key differentiates the sig-
naling environment voltages.
The same physical connec-
tor is used for the 32 bit sig-
naling environments. In one
orientation, the key accepts
5 volt boards. When rotated
180°, the connector
accepts 3.3 volt signaling
boards. The pin numbering
of the connector changes
for the different signaling
environments to maintain
the same relative position of
signals on the connector.
Performance Specifications:
Durability—Tested to 100 mating
cycles
Mating Force—8 oz [2.22 N] max. per
contact pair
Unmating Force—.5 oz [0.14 N] min.
per contact pair
Contact Resistance—20 milliohms
max. (initial) 30 milliohms max. (final)
Insulation Resistance—
1000 megohms min.
Dielectric Withstanding Voltage—
500 VAC (at sea level)
Capacitance—2 picofarads max.
Current Rating—1 ampere max.
Voltage Rating—203 VAC
Thermal Shock—
–55°C to +85°C for 5 cycles
Mixed Flowing Gas—Class II with
mated board for 20 days
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
Qualification Test Report
501-203
8
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series PCI Card Edge Connectors
64 Bit, 5 Volt Signaling
92 Dual Positions
with 3 Plastic Pylons or
3 Metal Holddowns
Material and Finish:
Housing—High temperature thermo-
plastic 94V-0 rated, white
Contacts—Phosphor bronze, plated as
follows:
Plating B—Duplex plated .000015
[0.00038] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications—
page 7
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
Part Numbers
W Contact 5 Volt
(Post Length) Finish 3 Plastic 3 Metal
Pylons Holddowns
.100 Plating B 145166-2 —
2.54 Plating C 145166-4 145169-4
.125
3.18 Plating C 145166-8 145169-8
Surface
Mount Plating C —145113-1
Notes: 1. Connectors are supplied with either cored (shown above) or solid side
walls.
Notes: 2. Other connector sizes can be made available, consult Tyco
Electronics.
Plastic Pylons
Metal Holddowns
.350
[8.89]
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
Section L-L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.) .150
[3.81]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
5.040
[128.02]
.050
48 Spaces at [1.27] 31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
.300
[7.62]
.050
[1.27] Solder Tail C
(2 Plcs.) L
.610
[15.49]
See Note.
.150
[3.81]
Section L-L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
.050
48 Spaces at [1.27] 31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
Through
Hole Surface
Mount
.300
[7.62]
.17+.02
[4.318+.508]
.180
[4.57]
.180
[4.57]
.003
[.076]
.078
[1.98]
Ref.
.170±.020
[4.32±0.51]
.150
[3.81]
(2 Plcs.)
.050
[1.27] Solder
(2 Plcs.)Tail C
.300
[7.62]
L
9
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Part Numbers
WHousing Contact 2 Plastic 2 Metal
(Post Length) Material Finish Pylons Holddowns
.100 Plating A 145154-1 145167-1
Y Plating B 145154-2 —
2.54 Plating C 145154-4 145167-4
.118 ZPlating A 11299-1 —
3.00 Plating B 11299-6 —
.125
3.18 YPlating C 145154-8 —
Surface
Mount YPlating C — 145098-1
Notes: 1. Connectors are supplied with either cored (shown above) or solid side walls.
Notes: 2. Other connector sizes can be made available, consult Tyco Electronics.
Standard Edge .050 Series PCI Card Edge Connectors
32 Bit, 3.3 and 5 Volt
Signaling
60 Dual Positions
with 2 Plastic Pylons or
2 Metal Holddowns
Material and Finish:
Housing Y—High temperature thermo-
plastic 94V-0 rated, white
Housing Z—Nylon 6/6, white
Contacts—Phosphor bronze, plated as
follows:
Plating A—Duplex plated gold flash in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire con-
tact underplated .000050 [0.00127] min.
nickel
Plating B—Duplex plated .000015
[0.00038] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications—
page 7
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
(2 Plcs.)
.050
[1.27] Solder Tail C
(2 Plcs.)
.300
[7.62]
Section L-L
L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
3.340
[84.84]
.050
48 Spaces at [1.27]
10 Spaces
at .050
[1.27]
.078
[1.98]
Ref.
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
(2 Plcs.)
.050
[1.27] Solder
(2 Plcs.)Tail C
.300
[7.62]
Section L-L
L
.035
[0.89]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
.050
48 Spaces at [1.27]
10 Spaces
at .050
[1.27]
.075
[1.90]
(2 Plcs.)
Plastic Pylons
Metal Holddowns
Through
Hole
L
Surface
Mount
.300
[7.62]
.17+.02
[4.318+.508]
.180
[4.57]
.180
[4.57]
.003
[.076]
10
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series PCI Card Edge Connectors
64 Bit, 3.3 Volt Signaling
92 Dual Positions
with 3 Plastic Pylons or
3 Metal Holddowns
Material and Finish:
Housing—High temperature thermo-
plastic 94V-0 rated, white
Contacts—Phosphor bronze, plated as
follows:
Plating B—Duplex plated .000015
[0.00038] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Plating C—Duplex plated .000030
[0.00076] min. gold in contact area,
.000100 [0.00254] min. tin-lead on solder
tails, with entire contact underplated
.000050 [0.00127] min. nickel
Related Product Data:
Performance Specifications—
page 7
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
.050
[1.27] Solder Tail C
(2 Plcs.)
.300
[7.62]
Section L-L
L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
5.040
[128.02]
.050
48 Spaces at [1.27]
31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
Part Numbers
W Contact 3.3 Volt
(Post Length) Finish 3 Plastic 3 Metal
Pylons Holddowns
.100 Plating B — 145168-2
2.54 Plating C 1-145165-4 145168-4
.125
3.18 Plating C 1-145165-8 —
Surface
Mount Plating C — 145246-1
Notes: 1. Connectors are supplied with either cored (shown above) or solid
side walls.
Notes: 2. Other connector sizes can be made available, consult Tyco
Electronics.
.610
[15.49]
See Note.
.170±.020
[4.32±0.51]
.150
[3.81]
.300
[7.62]
Section L-L
.035
[0.89]
(2 Plcs.)
.075
[1.90]
(2 Plcs.) .150
[3.81]
(2 Plcs.)
.078
[1.98]
Ref.
.060
[1.52]
Typ.
W±.010
[±0.25]
Typ.
35°
(2 Plcs.)
L
L
.050
48 Spaces at [1.27]
31 Spaces
at .050
[1.27]
10 Spaces
at .050
[1.27]
.050
[1.27] Solder
(2 Plcs.)Tail C
L
Plastic Pylons
Metal Holddowns
Through
Hole Surface
Mount
.300
[7.62]
.17+.02
[4.318+.508]
.180
[4.57]
.180
[4.57]
.003
[.076]
11
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series Connectors
Product Facts
■High density .050 [1.27]
centerline spacing of
contacts
■Easy mating of high-circuit
count daughter boards
■Compatible with infrared
reflow (IR) soldering
techniques
■Polarizing web for positive
board-to-connector
registration
■Choice of plastic pylons or
metal holddowns
■Recognized under the
Component Program of
Underwriter
Laboratories Inc.
File No. E28476
■Certified by Canadian
Standards
Association,
File No. LR 7189
The need to conserve
space and pack more func-
tion into a given area has
demanded that .050 [1.27]
centerline spacing become
a reality. AMP Standard
Edge .050 Series connec-
tors are the ideal vehicle for
mother/daughter board
applications requiring this
real estate.
These rugged connectors
have two rows of contacts
on .050 [1.27] centerlines.
Polarizing webs provide
positive board-to-connector
registration, while insertion
force allows even high
circuit-count daughter
boards to mate easily. The
connectors accept .054 to
.070 [1.37 to 1.78] thick
daughter boards and fea-
ture an overstress protected
contact design.
AMP Standard Edge .050
Series connectors are ideal
for fast automated robotic
assembly with registration
features and dimensional
tolerancing for more accurate
pickup and placement, and
are packaged in robotics-
compatible trays.
Plastic guide posts or metal
holddowns align the con-
nector with the mother board
and retain it for soldering.
To make circuit routing easy,
connector solder posts are
arranged in a four-row .100
[2.54] staggered grid. High-
temperature tolerant mate-
rials promote that these
connectors withstand
infrared reflow (IR) solder-
ing, while standoffs ease
flux cleaning.
Performance Specifications:
Contact Current Rating* —1 ampere
Termination Resistance —
20 milliohms max. (initial)
30 milliohms max. (final)
Dielectric Withstanding Voltage —
500 VAC min.
Insulation Resistance — 1000
megohms min.
Mating Force — .5 oz. [0.14 N] per
contact pair
Unmating Force — 1 oz. [0.3 N] per
contact pair
Durability (Tested to) — 100 mating
cycles
Application Temperature —
+215°C for 120 seconds max.
Temperature Range —
–55°C to +85°C
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
High Density for DataBus
Applications
®
12
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series Connectors
Configuration;
1 Key—2 Plastic Pylons
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire con-
tact underplated .000050 [0.00127] min.
nickel
Related Product Data:
Performance Specifications—
page 11
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.060
[1.52] Typ.
.016
[0.41] Typ.
.170±.020
[4.32±0.51]
W
(Post
Length)
.300
[7.62]
.610
[15.49]
Section L-L
.035
[0.89]
(2 Plcs.)
.050
[1.27]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
35°
(2 Plcs.)
L
L
C
.075
[1.90]
(2 Plcs.)
.012
[0.30]
Typ.
A Spaces
at .050
[1.27]
B Spaces
at .050
[1.27]
No. of Dimensions W PC Board
Dual (Post Hole Connector
Positions ABC Length) Layout Part Numbers
1.490 .100
23 10 11 37.85 2.54 A0-650090-7
1.840 .100
30 10 18 46.74 2.54 B0-650090-6
.100
2.340 2.54 B0-650090-3
40 10 28 59.44 .140
3.56 B0-650181-2
2.590 .100
45 10 33 65.79 2.54 A0-650090-2
.100
3.140 2.54 B10-650090-11
56 10 44 79.76 .140
3.56 B0-650181-1
4.340 .100
80 37 41 110.24 2.54 C0-650090-9
.100
4.890 2.54 A10-650092-12
91 41 48 124.21 .140
3.56 A0-650092-2
1 Connector used for VLLocal Bus and MCA Bus applications.
2 Connector used for MCA Bus applications.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. .125 [3.18] post length is available, consult Tyco Electronics.
13
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Standard Edge .050 Series Connectors
Configuration;
1 Key—2 Plastic Pylons
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire
contact underplated .000050 [0.00127]
min. nickel
Related Product Data:
Performance Specifications—
page 11
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
.350
[8.89]
.060
[1.52] Typ.
.016
[0.41] Typ.
.096
[2.44]Dia. Max.
.170±.020
[4.32±0.51]
W
(Post
Length)
.300
[7.62]
.610
[15.49]
.150
[3.81]
Section L-L
.035
[0.89]
(2 Plcs.)
.050
[1.27]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
35°
(2 Plcs.)
L
L
D
.075
[1.90]
(2 Plcs.)
.012
[0.30]
Typ.
A Spaces
at .050
[1.27]
B Spaces
at .050
[1.27]
No. of Dimensions W PC Board
Dual (Post Hole Connector
Positions ABCDLength) Layout Part Numbers
.100
3.740 2.54 A1650091-1*
66 10 44 9 95.00 .140
3.56 A 650091-2
*Connectors used for MCA Bus applications.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. .125 [3.18] post length is available, consult Tyco Electronics.
C Spaces
at .050
[1.27]
14
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type Board-to-Board)
Configuration; End Key
Standard Edge .050 Series Connectors
Configuration;
1 Key/1 Web —3 Metal
Holddowns
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Holddowns—Brass, plated .000150
[0.00381] min. tin-lead over .000050
[0.00127] min. nickel
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire
contact underplated .000050 [0.00127]
min. nickel
Related Product Data:
Performance Specifications—
page 11
Technical Documents:
Product Specification
104-14034
Application Specification
114-26012
.060
[1.52] Typ.
.350
[8.89]
6.440
[163.58]
.610
[15.49]
Section L-L
.035
[0.89]
(2 Plcs.) 35°
(2 Plcs.)
L
L
.075
[1.90]
(2 Plcs.)
W
(Post
Length)
10Spaces
at .050
[1.27]
63 Spaces
at .050
[1.27]
44Spaces
at .050
[1.27]
.150
[3.81]
(2 Plcs.)
.150
[3.81]
.300
[7.62]
.170±.020
[4.32±0.51]
.180
[4.57]
.050
[1.27] Solder Tail C
(2 Plcs.) L
120 Dual Positions
No. of W Connector
Dual (Post Part
Positions Length) Numbers
120 .140
3.56 145031-3
Note: Other connector sizes can be made available, consult Tyco Electronics.
Material and Finish:
Housing—High temperature thermo-
plastic, brown
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] min. gold in
contact area, .000100 [0.00254] min.
tin-lead on solder tails, with entire con-
tact underplated .000050 [0.00127] min.
nickel
Related Product Data:
Performance Specifications—
page 11
Technical Documents:
Product Specification
108-14034
Application Specification
114-26012
No. of Dimensions
Dual Post Connector
Positions A B C D Length Part Numbers
1.480 1.350 1.310 .100
25 24 37.59 34.29 33.27 2.54 650719-1
Note: Other connector sizes can be made available, consult Tyco Electronics.
Section L-L
.050
[1.27]
(2 Plcs.)
.150
[3.81]
(2 Plcs.)
.170±.020
[4.32±0.51]
.300
[7.62]
.610
[15.49]
.075
[1.90]
.350
[8.89]
Post Length
35°
.035
[0.89]
.096
[2.44]
Dia.
Max.
.099
[2.52]
Max.
.012
[0.30] Typ.
.060
[1.52] Typ.
.016
[0.41] Typ.
L
B
L
ASpaces
at .050
[1.27]
15
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors
Product Facts
■Maximum number
of dual positions
.100 [2.54] Centerlines-70,
.125 [3.18] Centerlines-50,
.150 [3.81] Centerlines-31
■Selective gold plating of
contacts for high perfor-
mance at low cost
■.025 [0.64] square solid
posts meet standard wrap-
type specifications
■For flow solder applications
■Glass-filled polyester
housing is 94V-0 rated
■Accepts double sided
PC boards, .054-.070
[1.27-1.78] thick
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E28476
■Certified by Canadian
Standards
Association,
File No. LR 7189
AMP Standard Edge II
Connectors provide high
reliability and economy in
packages compatible with
industry standards for dou-
ble sided printed circuit
boards.
Tyco Electronics offers
Standard Edge II
Connectors with or without
mounting ears, for rack
mounting and soldering.
Contacts are arranged on
.100 [2.54] centers, .125
[3.18] centers, .150 [3.81]
centers, .200 [5.08]
row-to-row; and .250 [6.35]
row-to-row.
Right-angle connectors are
also available with contacts
arranged on .100 [2.54]
centers, .150 [3.81]
row-to-row or .200 [5.08]
row-to-row.
Card extenders with con-
tacts on .100 [2.54] and
.125 [3.18] centers also are
available.
Precision formed phosphor
bronze contacts are selec-
tively gold plated. Phosphor
bronze has excellent
strength characteristics
which help the connector
absorb load deflection
movement of a PC board
while maintaining sufficient
contact force for good elec-
trical connection. Bifurcated
cantilever beam contacts
provide redundant contact.
Performance Specifications
Contact Rating*: 3 amperes
continuous (UL and CSA)
Contact Resistance: 10 milliohms
max.
Operating Temperature: –55°C to
+85°C
Voltage Rating (Sea Level):
.100 [2.54] centerline—1000 VAC (test)
.125 [3.18] centerline—1500 VAC (test)
.150 [3.81] centerline—1500 VAC (test)
Insulation Resistance: 5000
megohms min., after exposure to
humidity
Vibration Tolerance: 10 to 500 hertz
Contact Engagement Force: 12 oz
[3.3 N] average per pair with .062 [1.57]
PC board
Contact Separation Force: 2 oz
[0.6 N] average per pair with .062 [1.57]
PC board
Humidity Tolerance: 90%-95% for
96 hours
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
16
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors Styles
.100 [2.54] and .125 [3.18] Centerline Solder Posts
without Mounting Ears
Pages 17 and 18
.100 [2.54] and .125 [3.18] Centerline Solder Posts
with Low and Mid-High Mounting Ears
Page 20
.100 [2.54] and .125 [3.18] Centerline Wrap-Type Posts
with Mid-High Mounting Ears
Page 21 .100 [2.54] Centerline Solder Posts with Board
Retention Feature, without Mounting Ears
Page 24
.100 [2.54] and .125 [3.18] Centerline
Card Extenders
Page 22
.150 [3.81] Centerline Solder Posts (with Board
Retention Feature), without Mounting Ears
Page 19
.100 [2.54] Centerline Right-Angle Posts
with Low and No Mounting Ears
Page 23
17
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Centerline,
Vertical Solder Posts,
Without Mounting Ears
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, duplex
plated as follows:
Plating A—.000030 [0.00076] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating B—.000015 [0.00038] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating C—Gold flash in contact area,
tin on posts, with entire contact nickel
underplated
Technical Documents:
Product Specification
108-9039
Material:
Natural color polyester
Intercontact Keying Plug
Part Number 650025-2
(.100 [2.54] Centerline)
No. of Dimensions Post Part Numbers
Dual
Positions A B C** D Length* Plating A Plating B Plating C
.560 .450 Open .200
314.22 11.43 End 5.08 .125 10-650263-11— —
.860 .750 .700 .500 .125 7-530843-5
621.84 19.05 17.78 12.70 .187 7-530843-6 — —
1.260 1.150 1.100 .900 .125 5-530843-0
10 32.00 29.21 27.94 22.86 .187 4-530843-9 — —
1.460 1.350 1.300 1.100 .125 0-530843-112 37.08 34.29 33.02 27.94 — —
1.760 1.650 1.600 1.400 .125 0-530843-215 44.70 41.91 40.64 35.56 — —
1.960 1.850 1.800 1.600
17 49.78 46.99 45.72 40.64 .125 5-530843-3 — —
2.060 1.950 1.900 1.700
18 52.32 49.53 48.26 43.18 .125 0-530843-3 2-530843-7 1176137-11
2.260 2.150 2.100 1.900
20 57.40 54.61 53.34 48.26 .125 5-530843-4 — —
2.460 2.350 2.300 2.100 .125 0-530843-422 62.48 59.69 58.42 53.34 — —
2.760 2.650 2.600 2.400 .125 0-530843-525 70.10 67.31 66.04 60.96 — —
3.060 2.950 2.900 2.700
28 77.72 74.93 73.66 68.58 .125 0-530843-6 — —
3.260 3.150 3.100 2.900 .125 0-530843-7
30 82.80 80.01 78.74 73.66 .187 1-530843-8 — —
3.360 3.250 3.200 3.000 7-530843-031 85.34 82.55 81.28 76.20 .125 6-530843-5 —
3.860 3.750 3.700 3.500 .125 0-530843-836 98.04 95.25 93.98 88.90 — —
4.260 4.150 4.100 3.900
40 108.20 105.41 104.14 99.06 .187 2-530843-0 — —
5.260 5.150 5.100 4.900 .125 1-530843-1
50 133.60 130.81 129.54 124.46 — —
**Metric equivalent for post lengths are .125 = 3.18; .187 = 4.75.
**Cdimension is card slot length.
1 Connectors with Retention Feature.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics.
Retention Feature
(Open End Card Slot)
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.100
[2.54]
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
.295
[7.49]
.155
[3.94]
.191
[4.85]
Post
Length
.100
[2.54] Typ.
Intercontact Key Slot
.368
[9.35]
D
A
B
C**
18
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications—
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.125 [3.18] Centerline,
Vertical Solder Posts,
Without Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plug
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
Part No. 650025-1
(.125 [3.18] Centerline)
No. of Dimensions Post
Dual Part Numbers
Positions A B C** D Length*
1.035 .875 .875 .625
626.29 22.22 22.22 15.88 .125 650207-11
2.035 1.875 1.875 1.625
14 51.69 47.62 47.62 41.28 .187 5-530844-8
2.535 2.375 2.375 2.125
18 64.39 60.33 60.33 53.98 .187 1-530844-5
3.035 2.875 2.875 2.625
22 77.09 73.03 73.03 66.68 .187 1-530844-6
3.785 3.625 3.625 3.375
28 96.14 92.08 92.08 85.73 .187 1-530844-7
4.035 3.875 3.875 3.625
30 102.49 98.42 98.42 92.08 .187 1-530844-8
4.785 4.625 4.625 4.375
36 121.54 117.48 117.48 111.13 .187 1-530844-9
5.285 5.125 5.125 4.875
40 134.24 130.18 130.18 123.82 .187 2-530844-0
5.660 5.500 5.500 5.250
43 143.76 139.70 139.70 133.35 .125 1-530844-0
6.535 6.375 6.375 6.125 .125 1-530844-1
50 165.99 161.93 161.93 155.58 .187 2-530844-2
**Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75]
**Cdimension is card slot length.
1Connector with Retention Feature.
Note: Other connector sizes can be made available, consult Tyco Electronics.
Retention Feature
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.125
[3.18]
Intercontact Key Slot
.368
[9.35]
D
C**
Accepts
.054/.070
[1.37/1.77]
PC Board
.191/.203
[4.85/5.16]
.295
[7.49]
.155
[3.94]
.241
[6.11]
Post
Length
.610
[15.49]
.125
[3.18]
.550
[13.97]
.060
[1.52]
A
B
19
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications—
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.150 [3.81] Centerline,
Vertical Solder Posts,
Retention Feature, Without
Mounting Ears
No. of Dimensions Retention Post Part
Dual Location Numbers
Positions A B Length*
1.650 1.920 7-10,
12 41.91 48.77 15-18 .135 1-650728-2
2.700 2.970 7-10,
19 68.58 75.44 29-32 .135 1-650728-9
4.050 4.320 7-10,
28 102.87 109.73 25-32,47-50 .135 2-650728-9
4.500 4.770 7-10,
31 114.30 121.16 27-34,53-56 .135 3-650728-1
**Metric equivalent for post length is .135 = [3.43]
**Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
B±.010
[±0.25]
Inter-Contact
Keying Slot
.600
[15.21]
.025
[0.63]
Spaces at .150 = Dim A Ref.
[3.81]
.024 [0.61]
.020 [0.51]
.305
[9.27]
Card Slot Accepts
.054-.070 [1.37-1.78]
Printed Circuit Board
.045 [1.14]
Contact
Area
.015
[0.38]
.080
[.203]
Lead in
Area
.200±.020
[5.08±0.51]
.016 [0.41]
.020 [0.51]
.200
[5.08]
.035±.020
[3.430±0.51]
.432
[10.97]
+.005
-.010
+0.13
-0.25
0.143–.161
[3.63–4.03]
20
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
1.760 1.650 1.600 1.400 2.385 2.075 .100 .100 .191
15 44.70 41.91 40.64 35.56 67.18 52.71 2.54 2.54 4.85 .125 0-530841-2
2.060 1.950 1.900 1.700 2.645 2.375 .100 .100 .191
18 52.32 49.53 48.26 43.18 67.18 60.32 2.54 2.54 4.85 .125 0-530841-3
2.760 2.650 2.600 2.400 3.345 3.075 .100 .100 .191 .125 0-530841-5
25 70.10 67.31 66.04 60.96 84.96 78.11 2.54 2.54 4.85 .187 1-530841-6
3.260 3.160 3.100 2.900 3.845 3.575 .100 .100 .191
30 82.80 80.01 78.74 73.66 97.66 90.81 2.54 2.54 4.85 .187 1-530841-8
3.860 3.750 3.700 3.500 4.445 4.175 .100 .100 .191
36 98.04 95.25 93.98 88.90 112.90 106.21 2.54 2.54 4.85 .125 0-530841-8
.191 .125 1-530841-1
5.260 5.150 5.100 4.900 5.845 5.575 .100 .100 4.85 .187 2-530841-2
50 133.60 130.81 129.54 124.46 148.46 141.60 2.54 2.54 .141-.153
3.58-3.88 .125 0-650718-11, 2
**Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75]
**Cdimension is card slot length.
1Connector with Retention Feature.
2Connector with Mid-High Mounting Ears.
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
1.035 .875 .875 .625 1.555 1.295 .125 .125 .241
626.29 22.22 22.22 15.88 39.50 32.89 3.18 3.18 6.11 .125 1-531341-3
.241
3.785 3.505 3.625 3.375 4.305 4.045 .125 .125 6.11 .187 1-530842-7
28 96.14 89.03 92.08 85.73 109.35 102.74 3.18 3.18 .241
6.11 .187 23-531341-02
6.535 6.255 6.375 6.125 7.055 6.795 .125 .125 .241
50 165.99 158.88 161.93 155.58 179.20 172.59 3.18 3.18 6.11 .125 1-530842-1
**Metric equivalent for post lengths are .125 = [3.18]; .187 = [4.75]
**Cdimension is card slot length.
1Connector with Retention Feature.
2Connector with Mid-High Mounting Ears.
Note: Other connector sizes can be made available, consult Tyco Electronics.
.100 [2.54] Centerline
.125 [3.18] Centerline
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications—
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.100 [2.54] and .125 [3.18]
Centerline, Vertical Solder
Posts, Low and Mid-High
Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plugs
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
Part No. 650025-2
(.100 [2.54] Centerline)
Part No. 650025-1
(.125 [3.18] Centerline)
Low Mounting Ears
Mid-High Mounting Ears Retention Feature
.064 [1.63] Sq.
x .130 [3.30] Dp. .064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.150
[3.81]
.300
[7.62]
HG
F
A
J
D
C**
.360
[9.14]
.250
[6.35]
.250
[6.35]
.180
[4.57]
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
.295
[7.49]
.155
[3.94]
Post
Length
E
B
21
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
3.260 3.150 3.100 2.900 3.845 3.575 .100 .100 .200
30 82.80 80.01 78.74 73.66 97.41 90.80 2.54 2.54 5.08 .570 3-530396-3
3.860 3.750 3.700 3.500 4.435 4.175 .100 .100 .200
36 98.04 95.25 93.98 88.90 112.65 106.04 2.54 2.54 5.08 .570 3-530396-4
4.260 4.150 4.100 3.900 4.845 4.575 .100 .100 .200
40 108.20 105.41 104.14 99.06 123.06 116.21 2.54 2.54 5.08 .570 3-530396-4
**Metric equivalent for post length is .570 = [14.48].
**Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
**Metric equivalent for post length is .570 = [14.48].
**Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of Dimensions Post Part
Dual
Positions A B C** D E F G H J Length* Numbers
3.035 2.755 2.875 2.625 3.555 3.295 .125 .125 .250
22 77.09 69.98 73.02 66.67 90.30 83.69 3.18 3.18 6.35 .570 4-530825-5
.100 [2.54] Centerline
.125 [3.18] Centerline
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications—
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Special Application—page 96
.100 [2.54] and .125 [3.18]
Centerline, Vertical Wrap-
Type Posts, Mid-High
Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plugs
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
Part No. 650025-2
(.100 [2.54] Centerline)
Part No. 650025-1
(.125 [3.18] Centerline)
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.150
[3.81]
.300
[7.62]
H
G
F
D
C
A
J
.180
[4.57]
.250
[6.35]
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board .295
[7.49]
.155
[3.94]
Post
Length
E
B
22
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
No. of Dimensions
Dual
Positions A B C** D E F G H Part Numbers
5.260 5.160 5.100 4.900 5.845 5.575 .100 .100
50 133.60 130.81 129.54 124.46 148.46 141.60 2.54 2.54 530826-3
*Cdimension is card slot length.
1No mounting ears.
Note: Other connector sizes can be made available, consult Tyco Electronics.
.100 [2.54] Centerline
.125 [3.18] Centerline
.100 [2.54] and .125 [3.18]
Centerlines, Card Extender
Contacts
Material:
Natural color polyester
Intercontact Keying Plugs
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area, tin on posts, with entire contact
nickel underplated
Related Product Data:
Performance Specifications—
page 15
PC Board Hole Layout—page 26
PC Board Edge Pattern—page 27
Material:
Natural color nylon
Mounting Block
Part No. 650025-1
(.125 [3.18] Centerline)
Kit Part No.531250-4
Each kit includes 2 mounting blocks,
2 self tapping screws, #5 x .437
[11.10] and 2 roll pins, .075 x .250
[1.57 x 6.35]
No. of Dimensions
Dual
Positions A B C** D E F G H Part Numbers
4.785 4.505 4.625 4.375 5.035 5.045 .125 .125
36 121.54 114.43 117.48 111.13 134.75 128.14 3.18 3.18 530384-2
*Cdimension is card slot length.
Note: Other connector sizes can be made available, consult Tyco Electronics.
Technical Documents:
(pages 186, 187):
Product Specification
108-9039
.064 [1.63] Sq.
x .130 [3.30] Dp. .064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.062
[1.57] Dia.
Roll Pin
.150
[3.81]
.300
[7.62]
HG
F
D
C
A
.180
[4.67]
.250
[6.35]
.062
[1.57]
PC Board Ref.
.610
[15.49] .550
[13.97]
.060
[1.52]
Accepts
.054/.070
[1.37/1.77]
PC Board
Fits
.054/.070
[1.37/1.77]
PC Board
.295
[7.49]
.340
[8.63]
.155
[3.94]
.180
[4.57]
E
B
Card Extender
Connector
Housing Ref. #5 Self
Tapping
Screws
Mounting
Block
Part Number 650025-2
(.100 [2.54] Centerline)
23
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Right-Angle
Solder Posts, with Low and
No Mounting Ears
Low Mounting Ears
No Mounting Ears
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, duplex
plated as follows:
Plating A—.000030 [0.00076] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating B—.000015 [0.00038] gold in
contact area, tin on posts, with entire
contact nickel underplated
Related Product Data:
Performance Specifications—
page 15
Technical Documents:
Product Specification
108-9039
Material:
Natural color polyester
Intercontact Keying Plug
Part Number 650025-2
(.100 [2.54] Centerline)
No. of Dimensions Post Part Numbers
Dual
Positions A B C* D E F G1Length2(Plating A)
1.460 1.350 1.300 1.100 2.045 1.775 x.100x
12 37.08 34.29 33.02 27.94 51.94 45.08 .150 .090 3145089-13
2.060 1.950 1.900 1.700 2.645 2.375 x.100x
18 52.32 49.53 48.26 43.18 67.18 60.32 .150 .090 645384-1
2.260 2.150 2.100 1.900 2.845 2.575 x.100x
20 57.40 54.61 53.34 48.26 72.30 65.40 .150 .090 645384-3
*Cdimension is card slot length.
1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08].
2 Metric equivalent for post length is .090 = [2.27].
3 Connector with Board Locks.
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of Dimensions Post Part Numbers
Dual
Positions A B C* D G1Length2Plating A Plating B
1.760 1.650 1.600 1.400 .100x
15 44.70 41.91 40.64 35.56 .150 .090 650118-1 —
1.960 1.850 1.800 1.600 .100x
17 49.78 46.99 45.72 40.64 .200 .090 650187-1 —
2.760 2.350 2.600 2.400 .100x
25 70.10 67.61 66.04 60.96 .150 .090 — 532600-2
3.360 3.250 3.200 3.000 .100x
31 85.34 82.55 81.28 76.20 .150 .090 — 532600-4
3.460 3.350 3.300 3.100 .100x
32 87.88 85.09 83.82 78.74 .150 .090 — 532600-5
2.160 2.750 2.700 1.800 .100x
19 54.86 69.85 68.58 45.72 .150 .090 — 532600-6
*Cdimension is card slot length.
1 Metric equivalent for .100 x .150 and .100 x .200 are [2.54 x 3.81] and [2.54 x 5.08].
2 Metric equivalent for post length is .090 = [2.27].
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics.
Low Mounting Ears
With Board Locks
.064 [1.63] Sq.
x .130 [3.30] Dp. .064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.128
[3.25] Dia.
.295
[7.49]
.295
[7.49]
G
G
F
D
C
A
.300
[7.62]
.250
[6.25]
.610
[15.49] .550
[13.97]
.100
[2.54]
.100
[2.54]
Accepts
.054/.070
[1.37/1.77]
PC Board
Accepts
.054/.070
[1.37/1.77]
PC Board
Post
Length
Post
Length
.155
[3.94]
.155
[3.94]
.080
[1.82]
E
B
24
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Centerline
Vertical Solder Posts,
Retention Feature,
Without Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plug
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, duplex
plated as follows:
Plating A—.000030 [0.00076] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating B—.000015 [0.00038] gold in
contact area, tin on posts, with entire
contact nickel underplated
Plating C—Gold flash in contact area,
tin on posts, with entire contact nickel
underplated
Technical Documents:
Product Specification
108-9039
Part Number 650025-2
(.100 [2.54] Centerline)
Retention Feature
No. of Dimensions Post Retention PartNumbers
Dual
Positions A B C** D Length* Feature Plating A
2.060 1.950 1.900 1.700
18 52.32 49.53 48.26 43.18 .125 3-6, 31-34 1-645235-4
3.360 3.250 3.200 3.000 3-6, 29-32 or
31 85.34 82.55 81.28 76.20 .125 31-34, 57-60 1-645235-1
5.260 5.150 5.100 4.900 3-6, 49-52,
50 133.60 130.81 129.54 124.46 .125 95-98 1-645235-3
6.260 6.150 6.100 5.900 3-6, 55-58,
60 159.00 156.21 154.94 149.86 .125 63-66, 115-118 1-645235-8
**Metric equivalent for post length is .125 = [3.18].
**Cdimension is card slot length.
Notes: 1. Other connector sizes can be made available, consult Tyco Electronics.
2. High temperature IR reflow compatible connectors can be made available, consult Tyco Electronics.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.064 [1.63] Sq.
x .130 [3.30] Dp.
.368
[9.35]
Intercontact Key Slot
.295
[7.49]
.191
[4.85]
D
C
A
.610
[15.49] .550
[13.97]
.100
[2.54]
.100
[2.54] Typ.
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
Post
Length
.155
[3.94]
.060
[1.52]
B
25
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Card Edge Connectors
.100 [2.54] Centerline,
Special 18/31 Dual
Combination Connector,
Vertical Solder Posts,
Without Mounting Ears
Material:
Natural color polyester
Intercontact Keying Plug
Material and Finish:
Housing—Black glass-filled polyester,
94V-0 rated, except where noted
Contacts—Phosphor bronze, plated
with .000030 [0.00076] gold in contact
area (except where noted), tin on posts,
with entire contact nickel underplated
Technical Documents:
Product Specification
108-9039
Part Number 650025-2
(.100 [2.54] Centerline)
No. of Post Dimension Retention
Dual Part Numbers
Positions Type A Feature
.125 3-6, 41, 42, 645169-2
52 Solder Posts 3.18 51, 52, 93-96 1536128-11
.125
52 Solder Posts 3.18 None 645169-3
.125 3-14, 41, 42,
52 Solder Posts 3.18 51, 52, 85-96 645169-4
.125 5, 6, 31, 32, 2176139-12
52 Solder Posts 3.18 41, 42, 93, 94 2
.187
52 Solder Posts 4.75 None 650616-1
1 Housing material is high temperature glass-filled polyester, gray.
2 Contact area is gold flash.
Notes: 1. Card slot length is 5.300 [134.62].
2. Other connector sizes can be made available, consult
Tyco Electronics.
3. High temperature IR reflow compatible connectors can be
made available, consult Tyco Electronics.
Retention Feature
Solder Posts
.368
[9.35]
.295
[7.49]
.200
[5.08]
AA
.610
[15.49] .550
[13.97]
.100
[2.54] 1.900
[48.26] 3.200
[81.28]
5.460
[138.68]
5.350
[135.89]
.191
[4.85]
.100
[2.54]
.400
[10.16]
Accepts
.054/.070
[1.37/1.77]
PC Board
.141/.153
[3.58/3.88]
.060
[1.52]
26
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Recommended
PC Board Hole Layouts
Vertical Post Connectors
Right-Angle Post Connectors
Dimensions
Connector Type A B C D F
.100 .200 .040
Solder Post/Retention 2.54 5.08 1.02 See Note 1 See Note 2
.150 .200 .040
Solder Post/Retention 3.81 5.08 1.02 See Note 4 See Note 2
.125 .250 .040
Solder Post, Mounting Ears 3.18 6.35 1.02 See Note 3 See Note 3
.100/.125 .200/.250 .040
Solder Post, W/O Mounting Ears 2.54/3.18 5.08/6.35 1.02 See Note 4 See Note 2
.100 .200 .042
Wrap-Type Post 2.54 5.08 1.07 See Note 5 See Note 5
.125 .250 .042
Wrap-Type Post 3.18 6.35 1.07 See Note 5 See Note 5
Notes: 1. Refer to page 24 for DDimensions and Dual Positions.
2. No mounting ears. Dimensions do not apply.
3. Refer to page 20 for Dand FDimensions and Dual Positions.
4. Refer to pages 18 and 19 for DDimensions and Dual Positions.
5. Refer to page 21 for Dand FDimensions and Dual Positions.
Notes: 1. Refer to page 23 for Dand FDimensions and Dual Positions.
2. Refer to page 23 for DDimensions and Dual Positions.
3. No Mounting Ears, Dimensions do not apply.
Dimensions
Connector Type A B C D F G
.100 .150 .042 .137
Right-Angle Posts, Mounting Ears 2.54 3.81 1.07 See Note 1 See Note 1 3.48
.100 .150 or .200 .042
Right-Angle Posts, No Mounting Ears 2.54 3.81 or 5.08 1.07 See Note 2 See Note 3 See Note 3
.128
[3.25] Dia.
C±.003 Dia.
[±0.08]
DB
F
A
.128
[3.25] Dia.
C±.003 Dia.
[±0.08]
D
G
B
F
A
.337
[8.56]
27
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Standard Edge II Connectors (Continued)
Recommended
PC Board Edge Pattern
PC Board Edge Pattern for
.100 [2.54] and .125 [3.18]
Centerline
.310
[7.87] Min.
C±.005
[±0.13]
D±.005
[±0.13]
B
A
.295
[7.49] Min.
Engagement Depth
.050
[1.27]
Intercontact Key Slot
.054/.070
[1.37/1.77]
.015
[0.38] x 45°
Chamfer
Datum C
L
No. of .100 [2.54] Centerline .125 [3.18] Centerline
Dual A = .093 [2.36] A = .118 [3.00]
Positions B = .050 [1.27] B = .075 [1.90]
C D C D
.386 .200
39.80 5.08 — —
.686 .500 .861 .625
617.42 12.70 21.87 15.88
1.086 .900 1.361 1.125
10 27.58 22.86 34.57 28.58
1.286 1.100
12 32.66 27.94 — —
1.386 1.200
13 35.20 30.48 — —
1.861 1.625
14 — — 47.27 41.28
1.586 1.400
15 40.28 35.56 — —
1.786 1.600
17 45.36 40.64 — —
1.886 1.700 2.361 2.125
18 47.90 43.18 59.97 53.98
2.286 2.100 2.861 2.625
22 58.06 53.34 72.67 66.68
2.586 2.400
25 65.68 60.96 — —
2.886 2.700 3.611 3.375
28 73.30 68.58 91.72 85.73
3.086 2.900 3.861 3.625
30 78.38 73.66 98.07 92.08
3.186 3.000 3.986 3.750
31 80.92 76.20 101.24 95.25
3.586 3.400
35 91.08 86.36 — —
3.686 3.500 4.611 4.375
36 93.62 88.90 117.12 111.13
4.086 3.900 5.111 4.875
40 103.78 99.06 129.82 123.82
4.386 4.200 5.486 5.250
43 111.40 106.68 139.34 133.35
5.086 4.900 6.361 6.125
50 129.18 124.46 161.57 155.58
6.086 5.900
60 154.58 149.86 — —
7.086 6.900
70 179.98 175.26 — —
28
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Card Edge Connectors
Product Facts
■Double readout Card Edge
connectors use dip solder
contacts
■Large lead-in chamfers
allow easy PC board
installation
■Insulator standoffs prevent
solder from wicking
■Various lengths for custom
applications
■Contact option, single or
dual row
Cantilever Beam
The Cantilever Beam Card
Edge connector comes with
standard high temperature
plastic insulators. Contacts
are available in a variety of
lengths to accommodate
various custom applica-
tions. Standoffs allow for
cleaning and draining and
are available as an option
on most insulator bodies.
Cantilever Beam Card Edge
offers a variety of card slot
depths. A full scoop option
is available for ease of
installation in applications
where visibility is limited.
Contact options vary in this
series from dual row stan-
dard contacts, single row
options and press-fit.
Design Advantages
• Circuit Integrity: Robust
cantilever contacts are
designed to promote
optimal normal forces at
the lowest possible cost.
Our uniquely contoured
contact mating surface
gives you constant
engagement, even when
subjected to continuous
vibration.
• Ease of Assembly:
Generous lead-in cham-
fers let your P.C. board
slide easily into the con-
nector. Insulator standoffs
are provided to facilitate
cleaning and prevent sol-
der from wicking.
Availability, flexibility, per-
formance and very low cost
make the Cantilever Series
from Tyco Electronics the
clear choice in Card Edge
connectors.
Description
The Cantilever Beam Series
products from Tyco
Electronics are double
readout cardedge
connectors, using dip
solder contacts. Tooled for
flexible manufacturing,
these Card Edge
connectors are readily
available in a broad
assortment of sizes and
mounting styles. Our
connectors meet industry
standards.
29
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Ordering Information
Acquired Part Number
C8D52DS29C1M191 – Insulator with molded-in polarizing key with card
guide chamber. The card slot lengths are 1.900 [48.26] and 3.200 [81.28].
Includes retention tails for .062 [1.57] PCB to hold connectors securely during
handling.
C8D52DS29C1M195 – Same as above. No retention tails.
.400
[10.16]
.13
[3.30]
.145
[3.68] .300
[7.62] Card Slot Depth
.200
[5.08]
.100
[2.54]
.040±.003
[1.02±.080] Dia.
.020±.010
[.51±.25] Contact Gap
3.000
[76.20]
1.900
[48.26]
5.100
[129.54]
3.70
[9.40]
.06
[1.52]
.06
[1.52]
.610
[15.49]
.200
[5.08] Ref.
.100
[2.54] Ref.
.100
[2.54] Typ.
3.200
[81.28]
.300
[7.62]
5.300
[134.62]
5.460
[138.68]
1.700
[43.18]
.200
[5.08]
30
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors .100 x .200 [2.54 x 5.08] Centerline
Dip Solder Tails, .300 [7.62] Card Slot Depth
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Daughter Card Edge Pattern—
page 57
Mounting Styles
.200
[5.08]
.100
[2.54]
.200
[5.08]
.610
[15.49]
.250
[6.35]
.180
[4.57]
.060
[1.52]
D
E
B
A
C
E
Dim E
Dim B
J
.145
[3.68] .300
[7.62] Card Slot Depth
.100
[2.54] Typ.
.020
[0.51] Typ. Dia.
.020±.010
[.51±.25] Contact Gap
.040±.003
[1.02±.08] Dia.
#4-40
.250
[6.35] .250
[6.35]
.125
[3.18] Dia.
.128
[3.25] Dia.
.125
[3.18] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
.370
[9.40]
31
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l ABCDEMounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .130" [3.30] (DIM “J”)
61 . 4 3 5 1 . 1 7 5 0 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 D S 2 9 A 1 C 8 D 0 6 D S 2 9 B 1 C 8 D 0 6 D S 2 9 C 1 C 8 D 0 6 D S 2 9 D 1 C 8 D 0 6 D S 2 9 E 1
3 6 . 4 5 2 9 . 8 5 2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 D S 2 9 A 1 C 8 D 1 0 D S 2 9 B 1 C 8 D 1 0 D S 2 9 C 1 C 8 D 1 0 D S 2 9 D 1 C 8 D 1 0 D S 2 9 E 1
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 D S 2 9 A 1 C 8 D 1 2 D S 2 9 B 1 C 8 D 1 2 D S 2 9 C 1 C 8 D 1 2 D S 2 9 D 1 C 8 D 1 2 D S 2 9 E 1
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 D S 2 9 A 1 C 8 D 1 5 D S 2 9 B 1 C 8 D 1 5 D S 2 9 C 1 C 8 D 1 5 D S 2 9 D 1 C 8 D 1 5 D S 2 9 E 1
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 C 8 D 1 8 D S 2 9 A 1 C 8 D 1 8 D S 2 9 B 1 C 8 D 1 8 D S 2 9 C 1 C 8 D 1 8 D S 2 9 D 1 C 8 D 1 8 D S 2 9 E 1
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 D S 2 9 A 1 C 8 D 2 0 D S 2 9 B 1 C 8 D 2 0 D S 2 9 C 1 C 8 D 2 0 D S 2 9 D 1 C 8 D 2 0 D S 2 9 E 1
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 D S 2 9 A 1 C 8 D 2 2 D S 2 9 B 1 C 8 D 2 2 D S 2 9 C 1 C 8 D 2 2 D S 2 9 D 1 C 8 D 2 2 D S 2 9 E 1
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 D S 2 9 A 1 C 8 D 2 5 D S 2 9 B 1 C 8 D 2 5 D S 2 9 C 1 C 8 D 2 5 D S 2 9 D 1 C 8 D 2 5 D S 2 9 E 1
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 D S 2 9 A 1 C 8 D 2 8 D S 2 9 B 1 C 8 D 2 8 D S 2 9 C 1 C 8 D 2 8 D S 2 9 D 1 C 8 D 2 8 D S 2 9 E 1
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 D S 2 9 A 1 C 8 D 3 0 D S 2 9 B 1 C 8 D 3 0 D S 2 9 C 1 C 8 D 3 0 D S 2 9 D 1 C 8 D 3 0 D S 2 9 E 1
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 D S 2 9 A 1 C 8 D 3 1 D S 2 9 B 1 C 8 D 3 1 D S 2 9 C 1 C 8 D 3 1 D S 2 9 D 1 C 8 D 3 1 D S 2 9 E 1
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 D S 2 9 A 1 C 8 D 3 5 D S 2 9 B 1 C 8 D 3 5 D S 2 9 C 1 C 8 D 3 5 D S 2 9 D 1 C 8 D 3 5 D S 2 9 E 1
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 D S 2 9 A 1 C 8 D 3 6 D S 2 9 B 1 C 8 D 3 6 D S 2 9 C 1 C 8 D 3 6 D S 2 9 D 1 C 8 D 3 6 D S 2 9 E 1
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 D S 2 9 A 1 C 8 D 4 0 D S 2 9 B 1 C 8 D 4 0 D S 2 9 C 1 C 8 D 4 0 D S 2 9 D 1 C 8 D 4 0 D S 2 9 E 1
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 D S 2 9 A 1 C 8 D 4 3 D S 2 9 B 1 C 8 D 4 3 D S 2 9 C 1 C 8 D 4 3 D S 2 9 D 1 C 8 D 4 3 D S 2 9 E 1
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 D S 2 9 A 1 C 8 D 5 0 D S 2 9 B 1 C 8 D 5 0 D S 2 9 C 1 C 8 D 5 0 D S 2 9 D 1 C 8 D 5 0 D S 2 9 E 1
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 D S 2 9 A 1 C 8 D 6 0 D S 2 9 B 1 C 8 D 6 0 D S 2 9 C 1 C 8 D 6 0 D S 2 9 D 1 C 8 D 6 0 D S 2 9 E 1
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
Tail Length .160" [4.06] (DIM “J”)
61 . 4 3 5 1 . 1 7 5 0 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 D S 2 9 A 2 C 8 D 0 6 D S 2 9 B 2 C 8 D 0 6 D S 2 9 C 2 C 8 D 0 6 D S 2 9 D 2 C 8 D 0 6 D S 2 9 E 2
3 6 . 4 5 2 9 . 8 5 2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 D S 2 9 A 2 C 8 D 1 0 D S 2 9 B 2 C 8 D 1 0 D S 2 9 C 2 C 8 D 1 0 D S 2 9 D 2 C 8 D 1 0 D S 2 9 E 2
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 D S 2 9 A 2 C 8 D 1 2 D S 2 9 B 2 C 8 D 1 2 D S 2 9 C 2 C 8 D 1 2 D S 2 9 D 2 C 8 D 1 2 D S 2 9 E 2
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 D S 2 9 A 2 C 8 D 1 5 D S 2 9 B 2 C 8 D 1 5 D S 2 9 C 2 C 8 D 1 5 D S 2 9 D 2 C 8 D 1 5 D S 2 9 E 2
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 C 8 D 1 8 D S 2 9 A 2 C 8 D 1 8 D S 2 9 B 2 C 8 D 1 8 D S 2 9 C 2 C 8 D 1 8 D S 2 9 D 2 C 8 D 1 8 D S 2 9 E 2
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 D S 2 9 A 2 C 8 D 2 0 D S 2 9 B 2 C 8 D 2 0 D S 2 9 C 2 C 8 D 2 0 D S 2 9 D 2 C 8 D 2 0 D S 2 9 E 2
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 D S 2 9 A 2 C 8 D 2 2 D S 2 9 B 2 C 8 D 2 2 D S 2 9 C 2 C 8 D 2 2 D S 2 9 D 2 C 8 D 2 2 D S 2 9 E 2
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 D S 2 9 A 2 C 8 D 2 5 D S 2 9 B 2 C 8 D 2 5 D S 2 9 C 2 C 8 D 2 5 D S 2 9 D 2 C 8 D 2 5 D S 2 9 E 2
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 D S 2 9 A 2 C 8 D 2 8 D S 2 9 B 2 C 8 D 2 8 D S 2 9 C 2 C 8 D 2 8 D S 2 9 D 2 C 8 D 2 8 D S 2 9 E 2
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 D S 2 9 A 2 C 8 D 3 0 D S 2 9 B 2 C 8 D 3 0 D S 2 9 C 2 C 8 D 3 0 D S 2 9 D 2 C 8 D 3 0 D S 2 9 E 2
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 D S 2 9 A 2 C 8 D 3 1 D S 2 9 B 2 C 8 D 3 1 D S 2 9 C 2 C 8 D 3 1 D S 2 9 D 2 C 8 D 3 1 D S 2 9 E 2
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 D S 2 9 A 2 C 8 D 3 5 D S 2 9 B 2 C 8 D 3 5 D S 2 9 C 2 C 8 D 3 5 D S 2 9 D 2 C 8 D 3 5 D S 2 9 E 2
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 D S 2 9 A 2 C 8 D 3 6 D S 2 9 B 2 C 8 D 3 6 D S 2 9 C 2 C 8 D 3 6 D S 2 9 D 2 C 8 D 3 6 D S 2 9 E 2
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 D S 2 9 A 2 C 8 D 4 0 D S 2 9 B 2 C 8 D 4 0 D S 2 9 C 2 C 8 D 4 0 D S 2 9 D 2 C 8 D 4 0 D S 2 9 E 2
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 D S 2 9 A 2 C 8 D 4 3 D S 2 9 B 2 C 8 D 4 3 D S 2 9 C 2 C 8 D 4 3 D S 2 9 D 2 C 8 D 4 3 D S 2 9 E 2
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
32
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .160" [4.06] (DIM “J”) (Continued)
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 D S 2 9 A 2 C 8 D 5 0 D S 2 9 B 2 C 8 D 5 0 D S 2 9 C 2 C 8 D 5 0 D S 2 9 D 2 C 8 D 5 0 D S 2 9 E 2
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 D S 2 9 A 2 C 8 D 6 0 D S 2 9 B 2 C 8 D 6 0 D S 2 9 C 2 C 8 D 6 0 D S 2 9 D 2 C 8 D 6 0 D S 2 9 E 2
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
Tail Length .220" [5.59] (DIM “J”)
61 . 4 3 5 1 . 1 7 5 0 . 8 6 0 0 . 7 0 0 0 . 5 0 0 C 8 D 0 6 D S 2 9 A 3 C 8 D 0 6 D S 2 9 B 3 C 8 D 0 6 D S 2 9 C 3 C 8 D 0 6 D S 2 9 D 3 C 8 D 0 6 D S 2 9 E 3
3 6 . 4 5 2 9 . 8 5 2 1 . 8 4 1 7 . 7 8 1 2 . 7 0
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 C 8 D 1 0 D S 2 9 A 3 C 8 D 1 0 D S 2 9 B 3 C 8 D 1 0 D S 2 9 C 3 C 8 D 1 0 D S 2 9 D 3 C 8 D 1 0 D S 2 9 E 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 C 8 D 1 2 D S 2 9 A 3 C 8 D 1 2 D S 2 9 B 3 C 8 D 1 2 D S 2 9 C 3 C 8 D 1 2 D S 2 9 D 3 C 8 D 1 2 D S 2 9 E 3
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 C 8 D 1 5 D S 2 9 A 3 C 8 D 1 5 D S 2 9 B 3 C 8 D 1 5 D S 2 9 C 3 C 8 D 1 5 D S 2 9 D 3 C 8 D 1 5 D S 2 9 E 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 C 8 D 1 8 D S 2 9 A 3 C 8 D 1 8 D S 2 9 B 3 C 8 D 1 8 D S 2 9 C 3 C 8 D 1 8 D S 2 9 D 3 C 8 D 1 8 D S 2 9 E 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 C 8 D 2 0 D S 2 9 A 3 C 8 D 2 0 D S 2 9 B 3 C 8 D 2 0 D S 2 9 C 3 C 8 D 2 0 D S 2 9 D 3 C 8 D 2 0 D S 2 9 E 3
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 C 8 D 2 2 D S 2 9 A 3 C 8 D 2 2 D S 2 9 B 3 C 8 D 2 2 D S 2 9 C 3 C 8 D 2 2 D S 2 9 D 3 C 8 D 2 2 D S 2 9 E 3
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 C 8 D 2 5 D S 2 9 A 3 C 8 D 2 5 D S 2 9 B 3 C 8 D 2 5 D S 2 9 C 3 C 8 D 2 5 D S 2 9 D 3 C 8 D 2 5 D S 2 9 E 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 C 8 D 2 8 D S 2 9 A 3 C 8 D 2 8 D S 2 9 B 3 C 8 D 2 8 D S 2 9 C 3 C 8 D 2 8 D S 2 9 D 3 C 8 D 2 8 D S 2 9 E 3
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 C 8 D 3 0 D S 2 9 A 3 C 8 D 3 0 D S 2 9 B 3 C 8 D 3 0 D S 2 9 C 3 C 8 D 3 0 D S 2 9 D 3 C 8 D 3 0 D S 2 9 E 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 0 0 0 C 8 D 3 1 D S 2 9 A 3 C 8 D 3 1 D S 2 9 B 3 C 8 D 3 1 D S 2 9 C 3 C 8 D 3 1 D S 2 9 D 3 C 8 D 3 1 D S 2 9 E 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 6 . 2 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 C 8 D 3 5 D S 2 9 A 3 C 8 D 3 5 D S 2 9 B 3 C 8 D 3 5 D S 2 9 C 3 C 8 D 3 5 D S 2 9 D 3 C 8 D 3 5 D S 2 9 E 3
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 C 8 D 3 6 D S 2 9 A 3 C 8 D 3 6 D S 2 9 B 3 C 8 D 3 6 D S 2 9 C 3 C 8 D 3 6 D S 2 9 D 3 C 8 D 3 6 D S 2 9 E 3
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 C 8 D 4 0 D S 2 9 A 3 C 8 D 4 0 D S 2 9 B 3 C 8 D 4 0 D S 2 9 C 3 C 8 D 4 0 D S 2 9 D 3 C 8 D 4 0 D S 2 9 E 3
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 C 8 D 4 3 D S 2 9 A 3 C 8 D 4 3 D S 2 9 B 3 C 8 D 4 3 D S 2 9 C 3 C 8 D 4 3 D S 2 9 D 3 C 8 D 4 3 D S 2 9 E 3
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 9 0 0 C 8 D 5 0 D S 2 9 A 3 C 8 D 5 0 D S 2 9 B 3 C 8 D 5 0 D S 2 9 C 3 C 8 D 5 0 D S 2 9 D 3 C 8 D 5 0 D S 2 9 E 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 4 . 4 6
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 C 8 D 6 0 D S 2 9 A 3 C 8 D 6 0 D S 2 9 B 3 C 8 D 6 0 D S 2 9 C 3 C 8 D 6 0 D S 2 9 D 3 C 8 D 6 0 D S 2 9 E 3
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
33
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors 100 x .200 [2.54 x 5.08], .510 [12.95] and
.395 [10.03] Card Slot Depth, Full Scoop
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data
Daughter Card Edge Pattern—
page 57
.180
[4.57]
.054 to .071
Accepts [3.37 to 1.80] Thk. PC Board
.200
[5.08]
.100
[2.54]
.100
[2.54]
.180
[4.57]
.705
[17.91]
.390
[9.91]
Dim C
C
C
B
A
.02
[.51] Contact Gap
Card Slot
Depth
.040±.003
[1.02±.08] Dia.
34
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row Full Scoop
No. of Dual D i m e n s i o n s Acquired Part
Readout Pos. ABC N u m b e r
.510" [12.95] Card Slot Depth
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 D S 2 9 0 6 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 D S 2 9 0 6 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 D S 2 9 0 6 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 D S 2 9 0 6 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 D S 2 9 0 6 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 D S 2 9 0 6 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 D S 2 9 0 6 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 D S 2 9 0 6 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 D S 2 9 0 6 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 D S 2 9 0 6 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 D S 2 9 0 6 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 D S 2 9 0 6 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 D S 2 9 0 6 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
.395" [10.03] Card Slot Depth
1 8 2 . 0 3 4 1 . 9 0 4 1 . 7 0 0 W 8 D 1 8 D S 2 9 0 9 3
5 1 . 6 6 4 8 . 3 6 4 3 . 1 8
2 0 2 . 2 3 4 2 . 1 0 4 1 . 9 0 0 W 8 D 2 0 D S 2 9 0 9 3
5 6 . 7 4 5 3 . 4 4 4 8 . 2 6
2 2 2 . 4 3 4 2 . 3 0 4 2 . 1 0 0 W 8 D 2 2 D S 2 9 0 9 3
6 1 . 8 2 5 8 . 5 2 5 3 . 3 4
2 5 2 . 7 3 4 2 . 6 0 4 2 . 4 0 0 W 8 D 2 5 D S 2 9 0 9 3
6 9 . 4 4 6 6 . 1 4 6 0 . 9 6
2 8 3 . 0 3 4 2 . 9 0 4 2 . 7 0 0 W 8 D 2 8 D S 2 9 0 9 3
7 7 . 0 6 7 3 . 7 6 6 8 . 5 8
3 0 3 . 2 3 4 3 . 1 0 4 2 . 9 0 0 W 8 D 3 0 D S 2 9 0 9 3
8 2 . 1 4 7 8 . 8 4 7 3 . 6 6
3 5 3 . 7 3 4 3 . 6 0 4 3 . 4 0 0 W 8 D 3 5 D S 2 9 0 9 3
9 4 . 8 4 9 1 . 5 4 8 6 . 3 6
3 6 3 . 8 3 4 3 . 7 0 4 3 . 5 0 0 W 8 D 3 6 D S 2 9 0 9 3
9 7 . 3 8 9 4 . 0 8 8 8 . 9 0
4 0 4 . 2 3 4 4 . 1 0 4 3 . 9 0 0 W 8 D 4 0 D S 2 9 0 9 3
1 0 7 . 5 4 1 0 4 . 2 4 9 9 . 0 6
4 3 4 . 5 3 4 4 . 4 0 4 4 . 2 0 0 W 8 D 4 3 D S 2 9 0 9 3
1 1 5 . 1 6 1 1 1 . 8 6 1 0 6 . 6 8
4 5 4 . 7 3 4 4 . 6 0 4 4 . 4 0 0 W 8 D 4 5 D S 2 9 0 9 3
1 2 0 . 2 4 1 1 6 . 9 4 1 1 1 . 7 6
5 0 5 . 2 3 4 5 . 1 0 4 4 . 9 0 0 W 8 D 5 0 D S 2 9 0 9 3
1 3 2 . 9 4 1 2 9 . 6 4 1 2 4 . 4 6
6 0 6 . 2 3 4 6 . 1 0 4 5 . 9 0 0 W 8 D 6 0 D S 2 9 0 9 3
1 5 8 . 3 4 1 5 5 . 0 4 1 4 9 . 8 6
35
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series Connectors .125 x .250 [3.18 x 6.35] Centerline, Dip Solder
Tails, .300 [7.62] Card Slot Depth
Mounting Styles
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1000 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Daughter Card Edge Pattern—
page 57
.250
[6.35]
.370
[9.40]
.125
[3.18]
.250
[6.35]
.610
[15.49]
.250
[6.35]
.180
[4.57]
.060
[1.52]
D
E
B
A
C
E
Dim E
Dim B
J
.145
[3.68] .300
[7.62] Card Slot Depth
.100
[2.54] Typ.
.020
[0.51] Typ. Dia.
.020±.010
[.51±.25] Contact Gap
.040±.003
[1.02±.08] Dia.
#4-40
.250
[6.35] .250
[6.35]
.125
[3.18] Dia.
.128
[3.25] Dia.
.125
[3.18] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
36
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .130 [3.30] (DIM. “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 D S 2 9 A 1 C 7 D 0 6 D S 2 9 B 1 C 7 D 0 6 D S 2 9 C 1 C 7 D 0 6 D S 2 9 D 1 C 7 D 0 6 D S 2 9 E 1
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 D S 2 9 A 1 C 7 D 1 0 D S 2 9 B 1 C 7 D 1 0 D S 2 9 C 1 C 7 D 1 0 D S 2 9 D 1 C 7 D 1 0 D S 2 9 E 1
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 D S 2 9 A 1 C 7 D 1 5 D S 2 9 B 1 C 7 D 1 5 D S 2 9 C 1 C 7 D 1 5 D S 2 9 D 1 C 7 D 1 5 D S 2 9 E 1
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 D S 2 9 A 1 C 7 D 1 8 D S 2 9 B 1 C 7 D 1 8 D S 2 9 C 1 C 7 D 1 8 D S 2 9 D 1 C 7 D 1 8 D S 2 9 E 1
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 D S 2 9 A 1 C 7 D 2 2 D S 2 9 B 1 C 7 D 2 2 D S 2 9 C 1 C 7 D 2 2 D S 2 9 D 1 C 7 D 2 2 D S 2 9 E 1
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 D S 2 9 A 1 C 7 D 2 5 D S 2 9 B 1 C 7 D 2 5 D S 2 9 C 1 C 7 D 2 5 D S 2 9 D 1 C 7 D 2 5 D S 2 9 E 1
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 D S 2 9 A 1 C 7 D 2 8 D S 2 9 B 1 C 7 D 2 8 D S 2 9 C 1 C 7 D 2 8 D S 2 9 D 1 C 7 D 2 8 D S 2 9 E 1
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 D S 2 9 A 1 C 7 D 3 0 D S 2 9 B 1 C 7 D 3 0 D S 2 9 C 1 C 7 D 3 0 D S 2 9 D 1 C 7 D 3 0 D S 2 9 E 1
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 6 8 0 4 . 4 2 0 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 D S 2 9 A 1 C 7 D 3 1 D S 2 9 B 1 C 7 D 3 1 D S 2 9 C 1 C 7 D 3 1 D S 2 9 D 1 C 7 D 3 1 D S 2 9 E 1
1 1 8 . 8 7 1 1 2 . 2 7 1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 D S 2 9 A 1 C 7 D 3 5 D S 2 9 B 1 C 7 D 3 5 D S 2 9 C 1 C 7 D 3 5 D S 2 9 D 1 C 7 D 3 5 D S 2 9 E 1
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 D S 2 9 A 1 C 7 D 3 6 D S 2 9 B 1 C 7 D 3 6 D S 2 9 C 1 C 7 D 3 6 D S 2 9 D 1 C 7 D 3 6 D S 2 9 E 1
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 D S 2 9 A 1 C 7 D 4 0 D S 2 9 B 1 C 7 D 4 0 D S 2 9 C 1 C 7 D 4 0 D S 2 9 D 1 C 7 D 4 0 D S 2 9 E 1
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 D S 2 9 A 1 C 7 D 4 3 D S 2 9 B 1 C 7 D 4 3 D S 2 9 C 1 C 7 D 4 3 D S 2 9 D 1 C 7 D 4 3 D S 2 9 E 1
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 D S 2 9 A 1 C 7 D 5 0 D S 2 9 B 1 C 7 D 5 0 D S 2 9 C 1 C 7 D 5 0 D S 2 9 D 1 C 7 D 5 0 D S 2 9 E 1
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
Tail Length .160 [4.06] (DIM. “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 D S 2 9 A 3 C 7 D 0 6 D S 2 9 B 3 C 7 D 0 6 D S 2 9 C 3 C 7 D 0 6 D S 2 9 D 3 C 7 D 0 6 D S 2 9 E 3
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 D S 2 9 A 3 C 7 D 1 0 D S 2 9 B 3 C 7 D 1 0 D S 2 9 C 3 C 7 D 1 0 D S 2 9 D 3 C 7 D 1 0 D S 2 9 E 3
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 D S 2 9 A 3 C 7 D 1 5 D S 2 9 B 3 C 7 D 1 5 D S 2 9 C 3 C 7 D 1 5 D S 2 9 D 3 C 7 D 1 5 D S 2 9 E 3
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 D S 2 9 A 3 C 7 D 1 8 D S 2 9 B 3 C 7 D 1 8 D S 2 9 C 3 C 7 D 1 8 D S 2 9 D 3 C 7 D 1 8 D S 2 9 E 3
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 D S 2 9 A 3 C 7 D 2 2 D S 2 9 B 3 C 7 D 2 2 D S 2 9 C 3 C 7 D 2 2 D S 2 9 D 3 C 7 D 2 2 D S 2 9 E 3
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 D S 2 9 A 3 C 7 D 2 5 D S 2 9 B 3 C 7 D 2 5 D S 2 9 C 3 C 7 D 2 5 D S 2 9 D 3 C 7 D 2 5 D S 2 9 E 3
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 D S 2 9 A 3 C 7 D 2 8 D S 2 9 B 3 C 7 D 2 8 D S 2 9 C 3 C 7 D 2 8 D S 2 9 D 3 C 7 D 2 8 D S 2 9 E 3
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 D S 2 9 A 3 C 7 D 3 0 D S 2 9 B 3 C 7 D 3 0 D S 2 9 C 3 C 7 D 3 0 D S 2 9 D 3 C 7 D 3 0 D S 2 9 E 3
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 6 8 0 4 . 4 2 0 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 D S 2 9 A 3 C 7 D 3 1 D S 2 9 B 3 C 7 D 3 1 D S 2 9 C 3 C 7 D 3 1 D S 2 9 D 3 C 7 D 3 1 D S 2 9 E 3
1 1 8 . 8 7 1 1 2 . 2 7 1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 D S 2 9 A 3 C 7 D 3 5 D S 2 9 B 3 C 7 D 3 5 D S 2 9 C 3 C 7 D 3 5 D S 2 9 D 3 C 7 D 3 5 D S 2 9 E 3
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 D S 2 9 A 3 C 7 D 3 6 D S 2 9 B 3 C 7 D 3 6 D S 2 9 C 3 C 7 D 3 6 D S 2 9 D 3 C 7 D 3 6 D S 2 9 E 3
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 D S 2 9 A 3 C 7 D 4 0 D S 2 9 B 3 C 7 D 4 0 D S 2 9 C 3 C 7 D 4 0 D S 2 9 D 3 C 7 D 4 0 D S 2 9 E 3
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 D S 2 9 A 3 C 7 D 4 3 D S 2 9 B 3 C 7 D 4 3 D S 2 9 C 3 C 7 D 4 3 D S 2 9 D 3 C 7 D 4 3 D S 2 9 E 3
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 D S 2 9 A 3 C 7 D 5 0 D S 2 9 B 3 C 7 D 5 0 D S 2 9 C 3 C 7 D 5 0 D S 2 9 D 3 C 7 D 5 0 D S 2 9 E 3
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
37
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .220 [5.59] (DIM. “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 C 7 D 0 6 D S 2 9 A 4 C 7 D 0 6 D S 2 9 B 4 C 7 D 0 6 D S 2 9 C 4 C 7 D 0 6 D S 2 9 D 4 C 7 D 0 6 D S 2 9 E 4
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 C 7 D 1 0 D S 2 9 A 4 C 7 D 1 0 D S 2 9 B 4 C 7 D 1 0 D S 2 9 C 4 C 7 D 1 0 D S 2 9 D 4 C 7 D 1 0 D S 2 9 E 4
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 C 7 D 1 5 D S 2 9 A 4 C 7 D 1 5 D S 2 9 B 4 C 7 D 1 5 D S 2 9 C 4 C 7 D 1 5 D S 2 9 D 4 C 7 D 1 5 D S 2 9 E 4
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 C 7 D 1 8 D S 2 9 A 4 C 7 D 1 8 D S 2 9 B 4 C 7 D 1 8 D S 2 9 C 4 C 7 D 1 8 D S 2 9 D 4 C 7 D 1 8 D S 2 9 E 4
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 C 7 D 2 2 D S 2 9 A 4 C 7 D 2 2 D S 2 9 B 4 C 7 D 2 2 D S 2 9 C 4 C 7 D 2 2 D S 2 9 D 4 C 7 D 2 2 D S 2 9 E 4
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 C 7 D 2 5 D S 2 9 A 4 C 7 D 2 5 D S 2 9 B 4 C 7 D 2 5 D S 2 9 C 4 C 7 D 2 5 D S 2 9 D 4 C 7 D 2 5 D S 2 9 E 4
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 C 7 D 2 8 D S 2 9 A 4 C 7 D 2 8 D S 2 9 B 4 C 7 D 2 8 D S 2 9 C 4 C 7 D 2 8 D S 2 9 D 4 C 7 D 2 8 D S 2 9 E 4
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 C 7 D 3 0 D S 2 9 A 4 C 7 D 3 0 D S 2 9 B 4 C 7 D 3 0 D S 2 9 C 4 C 7 D 3 0 D S 2 9 D 4 C 7 D 3 0 D S 2 9 E 4
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 1 4 . 6 8 0 4 . 4 2 0 4 . 1 6 0 4 . 0 0 0 3 . 7 5 0 C 7 D 3 1 D S 2 9 A 4 C 7 D 3 1 D S 2 9 B 4 C 7 D 3 1 D S 2 9 C 4 C 7 D 3 1 D S 2 9 D 4 C 7 D 3 1 D S 2 9 E 4
1 1 8 . 8 7 1 1 2 . 2 7 1 0 5 . 6 6 1 0 1 . 6 0 9 5 . 2 5
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 C 7 D 3 5 D S 2 9 A 4 C 7 D 3 5 D S 2 9 B 4 C 7 D 3 5 D S 2 9 C 4 C 7 D 3 5 D S 2 9 D 4 C 7 D 3 5 D S 2 9 E 4
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 C 7 D 3 6 D S 2 9 A 4 C 7 D 3 6 D S 2 9 B 4 C 7 D 3 6 D S 2 9 C 4 C 7 D 3 6 D S 2 9 D 4 C 7 D 3 6 D S 2 9 E 4
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 C 7 D 4 0 D S 2 9 A 4 C 7 D 4 0 D S 2 9 B 4 C 7 D 4 0 D S 2 9 C 4 C 7 D 4 0 D S 2 9 D 4 C 7 D 4 0 D S 2 9 E 4
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 C 7 D 4 3 D S 2 9 A 4 C 7 D 4 3 D S 2 9 B 4 C 7 D 4 3 D S 2 9 C 4 C 7 D 4 3 D S 2 9 D 4 C 7 D 4 3 D S 2 9 E 4
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 C 7 D 5 0 D S 2 9 A 4 C 7 D 5 0 D S 2 9 B 4 C 7 D 5 0 D S 2 9 C 4 C 7 D 5 0 D S 2 9 D 4 C 7 D 5 0 D S 2 9 E 4
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
38
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Cantilever Series .156 x .200 [3.96 x 5.08] Centerline, Dip Solder Tails,
.300 [7.62] Card Slot Depth
Mounting Styles
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1500 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Daughter Card Edge Pattern—
page 57
.200
[5.08]
.156
[3.96]
.200
[5.08]
.610
[15.49]
.250
[6.35]
.180
[4.57]
.060
[1.52]
D
E
B
A
C
E
Dim E
Dim B
J
.145
[3.68] .300
[7.62] Card Slot Depth
.156
[3.96] Typ.
.020
[0.51] Typ. Dia.
.020±.010
[.51±.25] Contact Gap
.040±.003
[1.02±.08] Dia.
#4-40
.250
[6.35] .250
[6.35]
.125
[3.18] Dia.
.128
[3.25] Dia.
.125
[3.18] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
.370
[9.40]
39
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .130 [3.30] (DIM. “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 D S 2 9 A 1 C 6 D 0 6 D S 2 9 B 1 C 6 D 0 6 D S 2 9 C 1 C 6 D 0 6 D S 2 9 D 1 C 6 D 0 6 D S 2 9 E 1
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 D S 2 9 A 1 C 6 D 1 0 D S 2 9 B 1 C 6 D 1 0 D S 2 9 C 1 C 6 D 1 0 D S 2 9 D 1 C 6 D 1 0 D S 2 9 E 1
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 D S 2 9 A 1 C 6 D 1 2 D S 2 9 B 1 C 6 D 1 2 D S 2 9 C 1 C 6 D 1 2 D S 2 9 D 1 C 6 D 1 2 D S 2 9 E 1
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 D S 2 9 A 1 C 6 D 1 5 D S 2 9 B 1 C 6 D 1 5 D S 2 9 C 1 C 6 D 1 5 D S 2 9 D 1 C 6 D 1 5 D S 2 9 E 1
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 D S 2 9 A 1 C 6 D 1 8 D S 2 9 B 1 C 6 D 1 8 D S 2 9 C 1 C 6 D 1 8 D S 2 9 D 1 C 6 D 1 8 D S 2 9 E 1
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 9 6 8 3 . 7 1 8 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 D S 2 9 A 1 C 6 D 2 0 D S 2 9 B 1 C 6 D 2 0 D S 2 9 C 1 C 6 D 2 0 D S 2 9 D 1 C 6 D 2 0 D S 2 9 E 1
1 0 0 . 7 9 9 4 . 4 4 8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 5 3 . 2 7 6 C 6 D 2 2 D S 2 9 A 1 C 6 D 2 2 D S 2 9 B 1 C 6 D 2 2 D S 2 9 C 1 C 6 D 2 2 D S 2 9 D 1 C 6 D 2 2 D S 2 9 E 1
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 1 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 D S 2 9 A 1 C 6 D 2 5 D S 2 9 B 1 C 6 D 2 5 D S 2 9 C 1 C 6 D 2 5 D S 2 9 D 1 C 6 D 2 5 D S 2 9 E 1
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 D S 2 9 A 1 C 6 D 2 8 D S 2 9 B 1 C 6 D 2 8 D S 2 9 C 1 C 6 D 2 8 D S 2 9 D 1 C 6 D 2 8 D S 2 9 E 1
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 5 . 5 2 8 5 . 2 7 8 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 D S 2 9 A 1 C 6 D 3 0 D S 2 9 B 1 C 6 D 3 0 D S 2 9 C 1 C 6 D 3 0 D S 2 9 D 1 C 6 D 3 0 D S 2 9 E 1
1 4 0 . 4 1 1 3 4 . 0 6 1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 6 8 4 5 . 4 3 4 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 D S 2 9 A 1 C 6 D 3 1 D S 2 9 B 1 C 6 D 3 1 D S 2 9 C 1 C 6 D 3 1 D S 2 9 D 1 C 6 D 3 1 D S 2 9 E 1
1 4 4 . 3 7 1 3 8 . 0 2 1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 6 . 3 0 8 6 . 0 5 8 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 D S 2 9 A 1 C 6 D 3 5 D S 2 9 B 1 C 6 D 3 5 D S 2 9 C 1 C 6 D 3 5 D S 2 9 D 1 C 6 D 3 5 D S 2 9 E 1
1 6 0 . 2 2 1 5 3 . 8 7 1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 D S 2 9 A 1 C 6 D 3 6 D S 2 9 B 1 C 6 D 3 6 D S 2 9 C 1 C 6 D 3 6 D S 2 9 D 1 C 6 D 3 6 D S 2 9 E 1
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 D S 2 9 A 1 C 6 D 4 0 D S 2 9 B 1 C 6 D 4 0 D S 2 9 C 1 C 6 D 4 0 D S 2 9 D 1 C 6 D 4 0 D S 2 9 E 1
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 D S 2 9 A 1 C 6 D 4 3 D S 2 9 B 1 C 6 D 4 3 D S 2 9 C 1 C 6 D 4 3 D S 2 9 D 1 C 6 D 4 3 D S 2 9 E 1
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
5 0 8 . 6 4 8 8 . 3 9 8 8 . 0 8 5 7 . 9 6 4 7 . 6 4 4 C 6 D 5 0 D S 2 9 A 1 C 6 D 5 0 D S 2 9 B 1 C 6 D 5 0 D S 2 9 C 1 C 6 D 5 0 D S 2 9 D 1 C 6 D 5 0 D S 2 9 E 1
2 1 9 . 6 6 2 1 3 . 3 1 2 0 5 . 3 6 2 0 2 . 2 9 1 9 4 . 1 6
Tail Length .160 [4.06] (DIM. “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 D S 2 9 A 3 C 6 D 0 6 D S 2 9 B 3 C 6 D 0 6 D S 2 9 C 3 C 6 D 0 6 D S 2 9 D 3 C 6 D 0 6 D S 2 9 E 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 D S 2 9 A 3 C 6 D 1 0 D S 2 9 B 3 C 6 D 1 0 D S 2 9 C 3 C 6 D 1 0 D S 2 9 D 3 C 6 D 1 0 D S 2 9 E 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 D S 2 9 A 3 C 6 D 1 2 D S 2 9 B 3 C 6 D 1 2 D S 2 9 C 3 C 6 D 1 2 D S 2 9 D 3 C 6 D 1 2 D S 2 9 E 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 D S 2 9 A 3 C 6 D 1 5 D S 2 9 B 3 C 6 D 1 5 D S 2 9 C 3 C 6 D 1 5 D S 2 9 D 3 C 6 D 1 5 D S 2 9 E 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 D S 2 9 A 3 C 6 D 1 8 D S 2 9 B 3 C 6 D 1 8 D S 2 9 C 3 C 6 D 1 8 D S 2 9 D 3 C 6 D 1 8 D S 2 9 E 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 9 6 8 3 . 7 1 8 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 D S 2 9 A 3 C 6 D 2 0 D S 2 9 B 3 C 6 D 2 0 D S 2 9 C 3 C 6 D 2 0 D S 2 9 D 3 C 6 D 2 0 D S 2 9 E 3
1 0 0 . 7 9 9 4 . 4 4 8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 5 3 . 2 7 6 C 6 D 2 2 D S 2 9 A 3 C 6 D 2 2 D S 2 9 B 3 C 6 D 2 2 D S 2 9 C 3 C 6 D 2 2 D S 2 9 D 3 C 6 D 2 2 D S 2 9 E 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 1 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 D S 2 9 A 3 C 6 D 2 5 D S 2 9 B 3 C 6 D 2 5 D S 2 9 C 3 C 6 D 2 5 D S 2 9 D 3 C 6 D 2 5 D S 2 9 E 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 D S 2 9 A 3 C 6 D 2 8 D S 2 9 B 3 C 6 D 2 8 D S 2 9 C 3 C 6 D 2 8 D S 2 9 D 3 C 6 D 2 8 D S 2 9 E 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 5 . 5 2 8 5 . 2 7 8 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 D S 2 9 A 3 C 6 D 3 0 D S 2 9 B 3 C 6 D 3 0 D S 2 9 C 3 C 6 D 3 0 D S 2 9 D 3 C 6 D 3 0 D S 2 9 E 3
1 4 0 . 4 1 1 3 4 . 0 6 1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 6 8 4 5 . 4 3 4 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 D S 2 9 A 3 C 6 D 3 1 D S 2 9 B 3 C 6 D 3 1 D S 2 9 C 3 C 6 D 3 1 D S 2 9 D 3 C 6 D 3 1 D S 2 9 E 3
1 4 4 . 3 7 1 3 8 . 0 2 1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 6 . 3 0 8 6 . 0 5 8 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 D S 2 9 A 3 C 6 D 3 5 D S 2 9 B 3 C 6 D 3 5 D S 2 9 C 3 C 6 D 3 5 D S 2 9 D 3 C 6 D 3 5 D S 2 9 E 3
1 6 0 . 2 2 1 5 3 . 8 7 1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 D S 2 9 A 3 C 6 D 3 6 D S 2 9 B 3 C 6 D 3 6 D S 2 9 C 3 C 6 D 3 6 D S 2 9 D 3 C 6 D 3 6 D S 2 9 E 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 D S 2 9 A 3 C 6 D 4 0 D S 2 9 B 3 C 6 D 4 0 D S 2 9 C 3 C 6 D 4 0 D S 2 9 D 3 C 6 D 4 0 D S 2 9 E 3
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 D S 2 9 A 3 C 6 D 4 3 D S 2 9 B 3 C 6 D 4 3 D S 2 9 C 3 C 6 D 4 3 D S 2 9 D 3 C 6 D 4 3 D S 2 9 E 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
5 0 8 . 6 4 8 8 . 3 9 8 8 . 0 8 5 7 . 9 6 4 7 . 6 4 4 C 6 D 5 0 D S 2 9 A 3 C 6 D 5 0 D S 2 9 B 3 C 6 D 5 0 D S 2 9 C 3 C 6 D 5 0 D S 2 9 D 3 C 6 D 5 0 D S 2 9 E 3
2 1 9 . 6 6 2 1 3 . 3 1 2 0 5 . 3 6 2 0 2 . 2 9 1 9 4 . 1 6
40
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s T h r uH o l e i n s e r t Thru Hole i n s e r t
Tail Length .220" [5.59] (DIM. “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 C 6 D 0 6 D S 2 9 A 4 C 6 D 0 6 D S 2 9 B 4 C 6 D 0 6 D S 2 9 C 4 C 6 D 0 6 D S 2 9 D 4 C 6 D 0 6 D S 2 9 E 4
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 C 6 D 1 0 D S 2 9 A 4 C 6 D 1 0 D S 2 9 B 4 C 6 D 1 0 D S 2 9 C 4 C 6 D 1 0 D S 2 9 D 4 C 6 D 1 0 D S 2 9 E 4
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 C 6 D 1 2 D S 2 9 A 4 C 6 D 1 2 D S 2 9 B 4 C 6 D 1 2 D S 2 9 C 4 C 6 D 1 2 D S 2 9 D 4 C 6 D 1 2 D S 2 9 E 4
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 C 6 D 1 5 D S 2 9 A 4 C 6 D 1 5 D S 2 9 B 4 C 6 D 1 5 D S 2 9 C 4 C 6 D 1 5 D S 2 9 D 4 C 6 D 1 5 D S 2 9 E 4
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 C 6 D 1 8 D S 2 9 A 4 C 6 D 1 8 D S 2 9 B 4 C 6 D 1 8 D S 2 9 C 4 C 6 D 1 8 D S 2 9 D 4 C 6 D 1 8 D S 2 9 E 4
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 0 3 . 9 6 8 3 . 7 1 8 3 . 4 0 5 3 . 2 8 4 2 . 9 6 4 C 6 D 2 0 D S 2 9 A 4 C 6 D 2 0 D S 2 9 B 4 C 6 D 2 0 D S 2 9 C 4 C 6 D 2 0 D S 2 9 D 4 C 6 D 2 0 D S 2 9 E 4
1 0 0 . 7 9 9 4 . 4 4 8 6 . 4 9 8 3 . 4 1 7 5 . 2 9
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 5 3 . 2 7 6 C 6 D 2 2 D S 2 9 A 4 C 6 D 2 2 D S 2 9 B 4 C 6 D 2 2 D S 2 9 C 4 C 6 D 2 2 D S 2 9 D 4 C 6 D 2 2 D S 2 9 E 4
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 1 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 C 6 D 2 5 D S 2 9 A 4 C 6 D 2 5 D S 2 9 B 4 C 6 D 2 5 D S 2 9 C 4 C 6 D 2 5 D S 2 9 D 4 C 6 D 2 5 D S 2 9 E 4
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 C 6 D 2 8 D S 2 9 A 4 C 6 D 2 8 D S 2 9 B 4 C 6 D 2 8 D S 2 9 C 4 C 6 D 2 8 D S 2 9 D 4 C 6 D 2 8 D S 2 9 E 4
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 0 5 . 5 2 8 5 . 2 7 8 4 . 9 6 5 4 . 8 4 4 4 . 5 2 4 C 6 D 3 0 D S 2 9 A 4 C 6 D 3 0 D S 2 9 B 4 C 6 D 3 0 D S 2 9 C 4 C 6 D 3 0 D S 2 9 D 4 C 6 D 3 0 D S 2 9 E 4
1 4 0 . 4 1 1 3 4 . 0 6 1 2 6 . 1 1 1 2 3 . 0 4 1 1 4 . 9 1
3 1 5 . 6 8 4 5 . 4 3 4 5 . 1 2 1 5 . 0 0 0 4 . 6 8 0 C 6 D 3 1 D S 2 9 A 4 C 6 D 3 1 D S 2 9 B 4 C 6 D 3 1 D S 2 9 C 4 C 6 D 3 1 D S 2 9 D 4 C 6 D 3 1 D S 2 9 E 4
1 4 4 . 3 7 1 3 8 . 0 2 1 3 0 . 0 7 1 2 7 . 0 0 1 1 8 . 8 7
3 5 6 . 3 0 8 6 . 0 5 8 5 . 7 4 5 5 . 6 2 4 5 . 3 0 4 C 6 D 3 5 D S 2 9 A 4 C 6 D 3 5 D S 2 9 B 4 C 6 D 3 5 D S 2 9 C 4 C 6 D 3 5 D S 2 9 D 4 C 6 D 3 5 D S 2 9 E 4
1 6 0 . 2 2 1 5 3 . 8 7 1 4 5 . 9 2 1 4 2 . 8 5 1 3 4 . 7 2
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 C 6 D 3 6 D S 2 9 A 4 C 6 D 3 6 D S 2 9 B 4 C 6 D 3 6 D S 2 9 C 4 C 6 D 3 6 D S 2 9 D 4 C 6 D 3 6 D S 2 9 E 4
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 5 C 6 D 4 0 D S 2 9 A 4 C 6 D 4 0 D S 2 9 B 4 C 6 D 4 0 D S 2 9 C 4 C 6 D 4 0 D S 2 9 D 4 C 6 D 4 0 D S 2 9 E 4
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 6
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 C 6 D 4 3 D S 2 9 A 4 C 6 D 4 3 D S 2 9 B 4 C 6 D 4 3 D S 2 9 C 4 C 6 D 4 3 D S 2 9 D 4 C 6 D 4 3 D S 2 9 E 4
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
5 0 8 . 6 4 8 8 . 3 9 8 8 . 0 8 5 7 . 9 6 4 7 . 6 4 4 C 6 D 5 0 D S 2 9 A 4 C 6 D 5 0 D S 2 9 B 4 C 6 D 5 0 D S 2 9 C 4 C 6 D 5 0 D S 2 9 D 4 C 6 D 5 0 D S 2 9 E 4
2 1 9 . 6 6 2 1 3 . 3 1 2 0 5 . 3 6 2 0 2 . 2 9 1 9 4 . 1 6
41
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Card Edge Connectors
Product Facts
■Sizes from 6 to 65 dual
positions.
■Contact mating surface
optimizes reliability by
concentrating the normal
force in the actual
contact area.
■Mounting ear options
accommodate both Panel
and PC Board
attachment.
■Solder stand-offs
facilitate cleaning.
■Bifurcated contact
design provides
redundant points of
contact to maximize
reliability.
■ Tail lengths available to
accommodate .062"
[1.57] through .125"
[3.18] thick PCB Boards
and Wire Wrap
termination.
■Straight or Right Angle
contact configurations.
Bifurcated contact design provides maximum reliability
Description/Application
The modified bellows card
edge connectors are dual
readout and are designed
for reliable termination to
double sided PCB boards.
Modified Bellows
The modified bellows card
edge connector offers a
variety of tail lengths for sol-
der and wire wrap applica-
tions. Contacts are
available in straight tail or
right angle configurations to
meet your individual pur-
pose. The modified bellows
line of connectors offers a
variety of card slot depths
and has optional high tem-
perature plastic insulators.
42
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Connectors .100 x .200 [2.54 x 5.08], Straight Dip
Solder And Wire Wrap Tails
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.100
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern—
page 57
.250
[6.35]
.610
[15.49]
J
.100
[2.54]
.200
[5.08]
.368
[9.53]
C
E
B
A
D
.300
[7.62] Card Depth
.054 - .071
[1.37 - 1.80] P.C. Board
.200
[5.08]
.025
[.64] Sq
.180
[4.57]
.610
[15.49] Ref.
.100
[2.54] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
Centered Mounting Ear
4-40 Threaded Insert No Mounting Ears
P=.040 [1.02] Dip Solder Applications
P=.042 [1.07] For Wire Wrap Applications
Dim B
Dim E
43
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDE.125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .160" [4.06] (DIM “J”)
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 A 8 D 1 0 D S 2 9 A 2 A 8 D 1 0 D S 2 9 B 2 A 8 D 1 0 D S 2 9 C 2 A 8 D 1 0 D S 2 9 D 2 A 8 D 1 0 D S 2 9 E 2
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 A 8 D 1 2 D S 2 9 A 2 A 8 D 1 2 D S 2 9 B 2 A 8 D 1 2 D S 2 9 C 2 — —
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 A 8 D 1 5 D S 2 9 A 2 A 8 D 1 5 D S 2 9 B 2 A 8 D 1 5 D S 2 9 C 2 A 8 D 1 5 D S 2 9 D 2 A 8 D 1 5 D S 2 9 E 2
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 A 8 D 1 8 D S 2 9 A 2 A 8 D 1 8 D S 2 9 B 2 A 8 D 1 8 D S 2 9 C 2 A 8 D 1 8 D S 2 9 D 2 A 8 D 1 8 D S 2 9 E 2
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 A 8 D 2 0 D S 2 9 A 2 A 8 D 2 0 D S 2 9 B 2 A 8 D 2 0 D S 2 9 C 2 – –
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 A 8 D 2 2 D S 2 9 A 2 A 8 D 2 2 D S 2 9 B 2 A 8 D 2 2 D S 2 9 C 2 – –
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 A 8 D 2 5 D S 2 9 A 2 A 8 D 2 5 D S 2 9 B 2 A 8 D 2 5 D S 2 9 C 2 A 8 D 2 5 D S 2 9 D 2 A 8 D 2 5 D S 2 9 E 2
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 A 8 D 2 8 D S 2 9 A 2 A 8 D 2 8 D S 2 9 B 2 A 8 D 2 8 D S 2 9 C 2 – –
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 A 8 D 3 0 D S 2 9 A 2 A 8 D 3 0 D S 2 9 B 2 A 8 D 3 0 D S 2 9 C 2 A 8 D 3 0 D S 2 9 D 2 A 8 D 3 0 D S 2 9 E 2
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 A 8 D 3 1 D S 2 9 A 2 A 8 D 3 1 D S 2 9 B 2 A 8 D 3 1 D S 2 9 C 2 A 8 D 3 1 D S 2 9 D 2 A 8 D 3 1 D S 2 9 E 2
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 A 8 D 3 5 D S 2 9 A 2 A 8 D 3 5 D S 2 9 B 2 A 8 D 3 5 D S 2 9 C 2 – –
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 A 8 D 3 6 D S 2 9 A 2 A 8 D 3 6 D S 2 9 B 2 A 8 D 3 6 D S 2 9 C 2 – –
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 A 8 D 4 0 D S 2 9 A 2 A 8 D 4 0 D S 2 9 B 2 A 8 D 4 0 D S 2 9 C 2 – –
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 A 8 D 4 3 D S 2 9 A 2 A 8 D 4 3 D S 2 9 B 2 A 8 D 4 3 D S 2 9 C 2 – –
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 A 8 D 4 4 D S 2 9 A 2 A 8 D 4 4 D S 2 9 B 2 A 8 D 4 4 D S 2 9 C 2 – –
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 A 8 D 5 0 D S 2 9 A 2 A 8 D 5 0 D S 2 9 B 2 A 8 D 5 0 D S 2 9 C 2 A 8 D 5 0 D S 2 9 D 2 A 8 D 5 0 D S 2 9 E 2
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 A 8 D 6 0 D S 2 9 A 2 A 8 D 6 0 D S 2 9 B 2 A 8 D 6 0 D S 2 9 C 2 – –
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 A 8 D 6 5 D S 2 9 A 2 A 8 D 6 5 D S 2 9 B 2 A 8 D 6 5 D S 2 9 C 2 A 8 D 6 5 D S 2 9 D 2 A 8 D 6 5 D S 2 9 E 2
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6
Tail Length .220" [5.59] (DIM “J”)
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 A 8 D 1 0 D S 2 9 A 3 A 8 D 1 0 D S 2 9 B 3 A 8 D 1 0 D S 2 9 C 3 A 8 D 1 0 D S 2 9 D 3 A 8 D 1 0 D S 2 9 E 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 A 8 D 1 2 D S 2 9 A 3 A 8 D 1 2 D S 2 9 B 3 A 8 D 1 2 D S 2 9 C 3 – –
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 A 8 D 1 5 D S 2 9 A 3 A 8 D 1 5 D S 2 9 B 3 A 8 D 1 5 D S 2 9 C 3 A 8 D 1 5 D S 2 9 D 3 A 8 D 1 5 D S 2 9 E 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 A 8 D 1 8 D S 2 9 A 3 A 8 D 1 8 D S 2 9 B 3 A 8 D 1 8 D S 2 9 C 3 A 8 D 1 8 D S 2 9 D 3 A 8 D 1 8 D S 2 9 E 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 A 8 D 2 0 D S 2 9 A 3 A 8 D 2 0 D S 2 9 B 3 A 8 D 2 0 D S 2 9 C 3 – –
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 A 8 D 2 2 D S 2 9 A 3 A 8 D 2 2 D S 2 9 B 3 A 8 D 2 2 D S 2 9 C 3 – –
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 A 8 D 2 5 D S 2 9 A 3 A 8 D 2 5 D S 2 9 B 3 A 8 D 2 5 D S 2 9 C 3 A 8 D 3 5 D S 2 9 D 3 A 8 D 3 5 D S 2 9 E 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 A 8 D 2 8 D S 2 9 A 3 A 8 D 2 8 D S 2 9 B 3 A 8 D 2 8 D S 2 9 C 3 – –
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 A 8 D 3 0 D S 2 9 A 3 A 8 D 3 0 D S 2 9 B 3 A 8 D 3 0 D S 2 9 C 3 A 8 D 3 0 D S 2 9 D 3 A 8 D 3 0 D S 2 9 E 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 A 8 D 3 1 D S 2 9 A 3 A 8 D 3 1 D S 2 9 B 3 A 8 D 3 1 D S 2 9 C 3 A 8 D 3 1 D S 2 9 D 3 A 8 D 3 1 D S 2 9 E 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 A 8 D 3 5 D S 2 9 A 3 A 8 D 3 5 D S 2 9 B 3 A 8 D 3 5 D S 2 9 C 3 – –
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 A 8 D 3 6 D S 2 9 A 3 A 8 D 3 6 D S 2 9 B 3 A 8 D 3 6 D S 2 9 C 3 – –
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 A 8 D 4 0 D S 2 9 A 3 A 8 D 4 0 D S 2 9 B 3 A 8 D 4 0 D S 2 9 C 3 – –
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 A 8 D 4 3 D S 2 9 A 3 A 8 D 4 3 D S 2 9 B 3 A 8 D 4 3 D S 2 9 C 3 – –
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
44
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDE.125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .220" [5.59] (DIM “J”) (Continued)
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 A 8 D 4 4 D S 2 9 A 3 A 8 D 4 4 D S 2 9 B 3 A 8 D 4 4 D S 2 9 C 3 – –
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 A 8 D 5 0 D S 2 9 A 3 A 8 D 5 0 D S 2 9 B 3 A 8 D 5 0 D S 2 9 C 3 A 8 D 5 0 D S 2 9 D 3 A 8 D 5 0 D S 2 9 E 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 A 8 D 6 0 D S 2 9 A 3 A 8 D 6 0 D S 2 9 B 3 A 8 D 6 0 D S 2 9 C 3 – –
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 A 8 D 6 5 D S 2 9 A 3 A 8 D 6 5 D S 2 9 B 3 A 8 D 6 5 D S 2 9 C 3 A 8 D 6 5 D S 2 9 D 3 A 8 D 6 5 D S 2 9 E 3
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6
Tail Length .560" [14.22] (DIM “J”) for Wire Wrap Termination
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 A 8 D 1 0 W W 2 9 A 3 A 8 D 1 0 W W 2 9 B 3 – – –
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 A 8 D 1 2 W W 2 9 A 3 A 8 D 1 2 W W 2 9 B 3 – – –
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 A 8 D 1 5 W W 2 9 A 3 A 8 D 1 5 W W 2 9 B 3 – – –
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 A 8 D 1 8 W W 2 9 A 3 A 8 D 1 8 W W 2 9 B 3 – – –
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 A 8 D 2 0 W W 2 9 A 3 A 8 D 2 0 W W 2 9 B 3 – – –
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 A 8 D 2 2 W W 2 9 A 3 A 8 D 2 2 W W 2 9 B 3 – – –
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 A 8 D 2 5 W W 2 9 A 3 A 8 D 2 5 W W 2 9 B 3 – – –
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 A 8 D 2 8 W W 2 9 A 3 A 8 D 2 8 W W 2 9 B 3 – – –
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 A 8 D 3 0 W W 2 9 A 3 A 8 D 3 0 W W 2 9 B 3 – – –
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 A 8 D 3 1 W W 2 9 A 3 A 8 D 3 1 W W 2 9 B 3 – – –
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 A 8 D 3 5 W W 2 9 A 3 A 8 D 3 5 W W 2 9 B 3 – – –
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 A 8 D 3 6 W W 2 9 A 3 A 8 D 3 6 W W 2 9 B 3 – – –
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 A 8 D 4 0 W W 2 9 A 3 A 8 D 4 0 W W 2 9 B 3 – – –
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 A 8 D 4 3 W W 2 9 A 3 A 8 D 4 3 W W 2 9 B 3 – – –
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 A 8 D 4 4 W W 2 9 A 3 A 8 D 4 4 W W 2 9 B 3 – – –
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 A 8 D 5 0 W W 2 9 A 3 A 8 D 5 0 W W 2 9 B 3 – – –
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 A 8 D 6 0 W W 2 9 A 3 A 8 D 6 0 W W 2 9 B 3 – – –
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 A 8 D 6 5 W W 2 9 A 3 A 8 D 6 5 W W 2 9 B 3 – – –
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6
45
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Connectors .100 x .200 [2.54 x 5.08] and
.100 x .150 [2.54 x 3.81] Right Angle Dip Solder Tails
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair using
.0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add suffix
M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030 [0.00076]
gold in the mating area, tin/lead on tails,
.000100 [0.00254] minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern—
page 57
Mounting Styles
.100
SECTION X-X
ROTATED 90º
SECTION X-X
.14±.01
[3.56±.25]
.368
[9.35]
H
.025
[.64] Sq. Typ.
.100
[2.54] Ref.
.250
[6.35]
.100
[2.54]
.040±.003
[1.02±.08] Dia.
.054±.071
[1.37±1.890] PC Board
Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim G
Dim K
Dim B
A
B
E
D
C
Dim E
Dim H
Row to Row Spacing
.180
[4.57]
.250
[6.35]
.610
[15.49] Ref. .610
[15.49] Ref. .610
[15.49] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Cross
Drilled Hole
Centered Mounting Ear
.125 [3.18] Cross
Drilled Hole
No Mounting Ears .180
[4.57]
.250
[6.35]
46
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
46
Ordering Information
.100" [2.54] Centerline / .200" [5.08] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDEEar Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 0 R A 2 9 A A 8 D 1 0 R A 2 9 C A 8 D 1 0 R A 2 9 E A 8 D 1 0 R A 2 9 F
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6 1 1 . 9 4 7 . 3 7
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 2 R A 2 9 A A 8 D 1 2 R A 2 9 C A 8 D 1 2 R A 2 9 E –
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4 1 1 . 9 4 7 . 3 7
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 5 R A 2 9 A A 8 D 1 5 R A 2 9 C A 8 D 1 5 R A 2 9 E A 8 D 1 5 R A 2 9 F
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6 1 1 . 9 4 7 . 3 7
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 1 8 R A 2 9 A A 8 D 1 8 R A 2 9 C A 8 D 1 8 R A 2 9 E A 8 D 1 8 R A 2 9 F
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8 1 1 . 9 4 7 . 3 7
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 0 R A 2 9 A A 8 D 2 0 R A 2 9 C A 8 D 2 0 R A 2 9 E –
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6 1 1 . 9 4 7 . 3 7
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 2 R A 2 9 A A 8 D 2 2 R A 2 9 C A 8 D 2 2 R A 2 9 E –
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4 1 1 . 9 4 7 . 3 7
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 5 R A 2 9 A A 8 D 2 5 R A 2 9 C A 8 D 2 5 R A 2 9 E A 8 D 2 5 R A 2 9 F
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6 1 1 . 9 4 7 . 3 7
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 2 8 R A 2 9 A A 8 D 2 8 R A 2 9 C A 8 D 2 8 R A 2 9 E –
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8 1 1 . 9 4 7 . 3 7
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 0 R A 2 9 A A 8 D 3 0 R A 2 9 C A 8 D 3 0 R A 2 9 E A 8 D 3 0 R A 2 9 F
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6 1 1 . 9 4 7 . 3 7
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 1 R A 2 9 A A 8 D 3 1 R A 2 9 C A 8 D 3 1 R A 2 9 E A 8 D 3 1 R A 2 9 F
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4 1 1 . 9 4 7 . 3 7
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 5 R A 2 9 A A 8 D 3 5 R A 2 9 C A 8 D 3 5 R A 2 9 E –
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6 1 1 . 9 4 7 . 3 7
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 3 6 R A 2 9 A A 8 D 3 6 R A 2 9 C A 8 D 3 6 R A 2 9 E –
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0 1 1 . 9 4 7 . 3 7
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 4 0 R A 2 9 A A 8 D 4 0 R A 2 9 C A 8 D 4 0 R A 2 9 E –
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6 1 1 . 9 4 7 . 3 7
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 4 3 R A 2 9 A A 8 D 4 3 R A 2 9 C A 8 D 4 3 R A 2 9 E –
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8 1 1 . 9 4 7 . 3 7
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 4 4 R A 2 9 A A 8 D 4 4 R A 2 9 C A 8 D 4 4 R A 2 9 E –
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2 1 1 . 9 4 7 . 3 7
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 5 0 R A 2 9 A A 8 D 5 0 R A 2 9 C A 8 D 5 0 R A 2 9 E A 8 D 5 0 R A 2 9 F
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2 1 1 . 9 4 7 . 3 7
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 6 0 R A 2 9 A A 8 D 6 0 R A 2 9 C A 8 D 6 0 R A 2 9 E –
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6 1 1 . 9 4 7 . 3 7
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 0 . 4 7 0 0 . 2 9 0 A 8 D 6 5 R A 2 9 A A 8 D 6 5 R A 2 9 C A 8 D 6 5 R A 2 9 E A 8 D 6 5 R A 2 9 F
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6 1 1 . 9 4 7 . 3 7
47
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.100" [2.54] Centerline / .150" [3.81] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l M o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t ABCDEEar Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
1 0 1 . 8 3 5 1 . 5 7 5 1 . 2 6 0 1 . 1 0 0 0 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 0 R A 2 9 A M 2 3 3 A 8 D 1 0 R A 2 9 C M 2 3 3 A 8 D 1 0 R A 2 9 E M 2 3 3 A 8 D 1 0 R A 2 9 F M 2 3 3
4 6 . 6 1 4 0 . 0 1 3 2 . 0 0 2 7 . 9 4 2 2 . 8 6 1 0 . 6 7 6 . 1 0
1 2 2 . 0 3 5 1 . 7 7 5 1 . 4 6 0 1 . 3 0 0 1 . 1 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 2 R A 2 9 A M 2 3 3 A 8 D 1 2 R A 2 9 C M 2 3 3 A 8 D 1 2 R A 2 9 E M 2 3 3 –
5 1 . 6 9 4 5 . 0 9 3 7 . 0 8 3 3 . 0 2 2 7 . 9 4 1 0 . 6 7 6 . 1 0
1 5 2 . 3 3 5 2 . 0 7 5 1 . 7 6 0 1 . 6 0 0 1 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 5 R A 2 9 A M 2 3 3 A 8 D 1 5 R A 2 9 C M 2 3 3 A 8 D 1 5 R A 2 9 E M 2 3 3 A 8 D 1 5 R A 2 9 F M 2 3 3
5 9 . 3 1 5 2 . 7 1 4 4 . 7 0 4 0 . 6 4 3 5 . 5 6 1 0 . 6 7 6 . 1 0
1 8 2 . 6 3 5 2 . 3 7 5 2 . 0 6 0 1 . 9 0 0 1 . 7 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 1 8 R A 2 9 A M 2 3 3 A 8 D 1 8 R A 2 9 C M 2 3 3 A 8 D 1 8 R A 2 9 E M 2 3 3 A 8 D 1 8 R A 2 9 F M 2 3 3
6 6 . 9 3 6 0 . 3 3 5 2 . 3 2 4 8 . 2 6 4 3 . 1 8 1 0 . 6 7 6 . 1 0
2 0 2 . 8 3 5 2 . 5 7 5 2 . 2 6 0 2 . 1 0 0 1 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 0 R A 2 9 A M 2 3 3 A 8 D 2 0 R A 2 9 C M 2 3 3 A 8 D 2 0 R A 2 9 E M 2 3 3 –
7 2 . 0 1 6 5 . 4 1 5 7 . 4 0 5 3 . 3 4 4 8 . 2 6 1 0 . 6 7 6 . 1 0
2 2 3 . 0 3 5 2 . 7 7 5 2 . 4 6 0 2 . 3 0 0 2 . 1 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 2 R A 2 9 A M 2 3 3 A 8 D 2 2 R A 2 9 C M 2 3 3 A 8 D 2 2 R A 2 9 E M 2 3 3 –
7 7 . 0 9 7 0 . 4 9 6 2 . 4 8 5 8 . 4 2 5 3 . 3 4 1 0 . 6 7 6 . 1 0
2 5 3 . 3 3 5 3 . 0 7 5 2 . 7 6 0 2 . 6 0 0 2 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 5 R A 2 9 A M 2 3 3 A 8 D 2 5 R A 2 9 C M 2 3 3 A 8 D 2 5 R A 2 9 E M 2 3 3 A 8 D 2 5 R A 2 9 F M 2 3 3
8 4 . 7 1 7 8 . 1 1 7 0 . 1 0 6 6 . 0 4 6 0 . 9 6 1 0 . 6 7 6 . 1 0
2 8 3 . 6 3 5 3 . 3 7 5 3 . 0 6 0 2 . 9 0 0 2 . 7 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 2 8 R A 2 9 A M 2 3 3 A 8 D 2 8 R A 2 9 C M 2 3 3 A 8 D 2 8 R A 2 9 E M 2 3 3 –
9 2 . 3 3 8 5 . 7 3 7 7 . 7 2 7 3 . 6 6 6 8 . 5 8 1 0 . 6 7 6 . 1 0
3 0 3 . 8 3 5 3 . 5 7 5 3 . 2 6 0 3 . 1 0 0 2 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 0 R A 2 9 A M 2 3 3 A 8 D 3 0 R A 2 9 C M 2 3 3 A 8 D 3 0 R A 2 9 E M 2 3 3 A 8 D 3 0 R A 2 9 F M 2 3 3
9 7 . 4 1 9 0 . 8 1 8 2 . 8 0 7 8 . 7 4 7 3 . 6 6 1 0 . 6 7 6 . 1 0
3 1 3 . 9 3 5 3 . 6 7 5 3 . 3 6 0 3 . 2 0 0 3 . 1 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 1 R A 2 9 A M 2 3 3 A 8 D 3 1 R A 2 9 C M 2 3 3 A 8 D 3 1 R A 2 9 E M 2 3 3 A 8 D 3 1 R A 2 9 F M 2 3 3
9 9 . 9 5 9 3 . 3 5 8 5 . 3 4 8 1 . 2 8 7 8 . 7 4 1 0 . 6 7 6 . 1 0
3 5 4 . 3 3 5 4 . 0 7 5 3 . 7 6 0 3 . 6 0 0 3 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 5 R A 2 9 A M 2 3 3 A 8 D 3 5 R A 2 9 C M 2 3 3 A 8 D 3 5 R A 2 9 E M 2 3 3 –
1 1 0 . 1 1 1 0 3 . 5 1 9 5 . 5 0 9 1 . 4 4 8 6 . 3 6 1 0 . 6 7 6 . 1 0
3 6 4 . 4 3 5 4 . 1 7 5 3 . 8 6 0 3 . 7 0 0 3 . 5 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 3 6 R A 2 9 A M 2 3 3 A 8 D 3 6 R A 2 9 C M 2 3 3 A 8 D 3 6 R A 2 9 E M 2 3 3 –
1 1 2 . 6 5 1 0 6 . 0 5 9 8 . 0 4 9 3 . 9 8 8 8 . 9 0 1 0 . 6 7 6 . 1 0
4 0 4 . 8 3 5 4 . 5 7 5 4 . 2 6 0 4 . 1 0 0 3 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 4 0 R A 2 9 A M 2 3 3 A 8 D 4 0 R A 2 9 C M 2 3 3 A 8 D 4 0 R A 2 9 E M 2 3 3 –
1 2 2 . 8 1 1 1 6 . 2 1 1 0 8 . 2 0 1 0 4 . 1 4 9 9 . 0 6 1 0 . 6 7 6 . 1 0
4 3 5 . 1 3 5 4 . 8 7 5 4 . 5 6 0 4 . 4 0 0 4 . 2 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 4 3 R A 2 9 A M 2 3 3 A 8 D 4 3 R A 2 9 C M 2 3 3 A 8 D 4 3 R A 2 9 E M 2 3 3 –
1 3 0 . 4 3 1 2 3 . 8 3 1 1 5 . 8 2 1 1 1 . 7 6 1 0 6 . 6 8 1 0 . 6 7 6 . 1 0
4 4 5 . 2 3 5 4 . 9 7 5 4 . 6 6 0 4 . 5 0 0 4 . 3 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 4 4 R A 2 9 A M 2 3 3 A 8 D 4 4 R A 2 9 C M 2 3 3 A 8 D 4 4 R A 2 9 E M 2 3 3 –
1 3 2 . 9 7 1 2 6 . 3 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 9 . 2 2 1 0 . 6 7 6 . 1 0
5 0 5 . 8 3 5 5 . 5 7 5 5 . 2 6 0 5 . 1 0 0 4 . 8 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 5 0 R A 2 9 A M 2 3 3 A 8 D 5 0 R A 2 9 C M 2 3 3 A 8 D 5 0 R A 2 9 E M 2 3 3 A 8 D 5 0 R A 2 9 F M 2 3 3
1 4 8 . 2 1 1 4 1 . 6 1 1 3 3 . 6 0 1 2 9 . 5 4 1 2 1 . 9 2 1 0 . 6 7 6 . 1 0
6 0 6 . 8 3 5 6 . 5 7 5 6 . 2 6 0 6 . 1 0 0 5 . 9 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 6 0 R A 2 9 A M 2 3 3 A 8 D 6 0 R A 2 9 C M 2 3 3 A 8 D 6 0 R A 2 9 E M 2 3 3 –
1 7 3 . 6 1 1 6 7 . 0 1 1 5 9 . 0 0 1 5 4 . 9 4 1 4 9 . 8 6 1 0 . 6 7 6 . 1 0
6 5 7 . 3 3 5 7 . 0 7 5 6 . 7 6 0 6 . 6 0 0 6 . 4 0 0 0 . 4 2 0 0 . 2 4 0 A 8 D 6 5 R A 2 9 A M 2 3 3 A 8 D 6 5 R A 2 9 C M 2 3 3 A 8 D 6 5 R A 2 9 E M 2 3 3 A 8 D 6 5 R A 2 9 F M 2 3 3
1 8 6 . 3 1 1 7 9 . 7 1 1 7 1 . 7 0 1 6 7 . 6 4 1 6 2 . 5 6 1 0 . 6 7 6 . 1 0
48
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
48
Modified Bellows Connectors .125 x .250 [3.18 x 6.35], Centerline Straight
Dip Solder and Wire Wrap Ta i l s
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—600 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern—
page 57
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.610
[5.49]
.250
[6.35]
.368
[9.35]
.025
[.64] Sq.
.125
[3.18] Ref.
.250
[6.35]
.125
[3.18]
.250
[6.35]
P±.003
[±.080] Dia.
.054±.071
[1.37±1.890] PC Board
.300
[7.62] Card Depth
P=.040 [1.02] Dip Solder Applications
P=.042 [1.07] For Wire Wrap Applications
Dim B
A
B
E
D
C
J
Dim E
.180
[4.57]
.250
[6.35]
.610
[15.49] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert Flush Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
4-40 Threaded Insert
No Mounting Ears
49
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Dip Solder Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .160" [4.06] (DIM “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 A 7 D 0 6 D S 2 9 A 2 A 7 D 0 6 D S 2 9 B 2 A 7 D 0 6 D S 2 9 C 2 A 7 D 0 6 D S 2 9 D 2 A 7 D 0 6 D S 2 9 E 2
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 A 7 D 1 0 D S 2 9 A 2 A 7 D 1 0 D S 2 9 B 2 A 7 D 1 0 D S 2 9 C 2 A 7 D 1 0 D S 2 9 D 2 A 7 D 1 0 D S 2 9 E 2
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 A 7 D 1 5 D S 2 9 A 2 A 7 D 1 5 D S 2 9 B 2 A 7 D 1 5 D S 2 9 C 2 A 7 D 1 5 D S 2 9 D 2 A 7 D 1 5 D S 2 9 E 2
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 A 7 D 1 8 D S 2 9 A 2 A 7 D 1 8 D S 2 9 B 2 A 7 D 1 8 D S 2 9 C 2 A 7 D 1 8 D S 2 9 D 2 A 7 D 1 8 D S 2 9 E 2
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 A 7 D 2 2 D S 2 9 A 2 A 7 D 2 2 D S 2 9 B 2 A 7 D 2 2 D S 2 9 C 2 – –
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 A 7 D 2 5 D S 2 9 A 2 A 7 D 2 5 D S 2 9 B 2 A 7 D 2 5 D S 2 9 C 2 A 7 D 2 5 D S 2 9 D 2 A 7 D 2 5 D S 2 9 E 2
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 A 7 D 2 8 D S 2 9 A 2 A 7 D 2 8 D S 2 9 B 2 A 7 D 2 8 D S 2 9 C 2 – –
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 A 7 D 3 0 D S 2 9 A 2 A 7 D 3 0 D S 2 9 B 2 A 7 D 3 0 D S 2 9 C 2 A 7 D 3 0 D S 2 9 D 2 A 7 D 3 0 D S 2 9 E 2
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 A 7 D 3 5 D S 2 9 A 2 A 7 D 3 5 D S 2 9 B 2 A 7 D 3 5 D S 2 9 C 2 – –
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 A 7 D 3 6 D S 2 9 A 2 A 7 D 3 6 D S 2 9 B 2 A 7 D 3 6 D S 2 9 C 2 – –
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 A 7 D 4 0 D S 2 9 A 2 A 7 D 4 0 D S 2 9 B 2 A 7 D 4 0 D S 2 9 C 2 – –
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 A 7 D 4 3 D S 2 9 A 2 A 7 D 4 3 D S 2 9 B 2 A 7 D 4 3 D S 2 9 C 2 – –
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 A 7 D 5 0 D S 2 9 A 2 A 7 D 5 0 D S 2 9 B 2 A 7 D 5 0 D S 2 9 C 2 A 7 D 5 0 D S 2 9 D 2 A 7 D 5 0 D S 2 9 E 2
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
.125" [3.18] Centerline / .250" [6.35] Row-to-Row Wire Wrap Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o Flush F l u s h
D u a l Mounting Ear Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t A B C D E .125" [3.18] 4-40 Threaded E a r s .125" [3.18] 4-40 Threaded
P o s i t i o n s Thru Hole i n s e r t Thru Hole i n s e r t
Tail Length .560" [14.22] (DIM “J”)
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 A 7 D 0 6 W W 2 9 A 3 A 7 D 0 6 W W 2 9 B 3 – – –
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 A 7 D 1 0 W W 2 9 A 3 A 7 D 1 0 W W 2 9 B 3 – – –
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 A 7 D 1 5 W W 2 9 A 3 A 7 D 1 5 W W 2 9 B 3 – – –
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 A 7 D 1 8 W W 2 9 A 3 A 7 D 1 8 W W 2 9 B 3 – – –
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 A 7 D 2 2 W W 2 9 A 3 A 7 D 2 2 W W 2 9 B 3 – – –
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 A 7 D 2 5 W W 2 9 A 3 A 7 D 2 5 W W 2 9 B 3 – – –
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 A 7 D 2 8 W W 2 9 A 3 A 7 D 2 8 W W 2 9 B 3 – – –
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 A 7 D 3 0 W W 2 9 A 3 A 7 D 3 0 W W 2 9 B 3 – – –
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 A 7 D 3 5 W W 2 9 A 3 A 7 D 3 5 W W 2 9 B 3 – – –
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 A 7 D 3 6 W W 2 9 A 3 A 7 D 3 6 W W 2 9 B 3 – – –
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 A 7 D 4 0 W W 2 9 A 3 A 7 D 4 0 W W 2 9 B 3 – – –
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 A 7 D 4 3 W W 2 9 A 3 A 7 D 4 3 W W 2 9 B 3 – – –
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 A 7 D 5 0 W W 2 9 A 3 A 7 D 5 0 W W 2 9 B 3 – – –
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8
50
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
50
Modified Bellows Connectors .125 x .250 [3.18 x 6.35], .125 x .150 [3.18 x 3.81],
.125 x .200 [3.18 x 5.08] Centerline, Right Angle Ta i l s
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1000 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern—
page 57
.125
[3.18] REF
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.180
[4.57]
.250
[6.35] .250
[6.35]
.250
[6.35]
.610
[15.49] Ref. .610
[15.49] Ref. .610
[15.49] Ref.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Cross
Drilled Hole
No Mounting Ears .180
[4.57]
Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only
.14±.01
[3.56±.25]
H
C
D
E
B
A
.025
[.64] Sq. Typ.
.054±.071
[1.37±1.890] PC Board
.125
[3.18]
.368
[9.35]
.040±.003
[1.02±.08] Dia.
Dim G
Dim K
Dim B
Dim E
Dim H
Row to Row Spacing
.128
[3.25] Dia.
51
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Ordering Information
.125" [3.18] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l ABCDEM o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t Ear Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
.150" [3.81] Row-to-Row (Dim. “H”) Spacing
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 0 6 R A 2 9 A M 2 3 1 A 7 D 0 6 R A 2 9 C M 2 3 1 A 7 D 0 6 R A 2 9 E M 2 3 1 A 7 D 0 6 R A 2 9 F M 2 3 1
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8 1 0 . 6 7 6 . 1 0
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 1 0 R A 2 9 A M 2 3 1 A 7 D 1 0 R A 2 9 C M 2 3 1 A 7 D 1 0 R A 2 9 E M 2 3 1 A 7 D 1 0 R A 2 9 F M 2 3 1
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8 1 0 . 6 7 6 . 1 0
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 0 . 4 2 0 0 . 2 4 0
A 7 D 1 5 R A 2 9 A M 2 3 1 A 7 D 1 5 R A 2 9 C M 2 3 1 A 7 D 1 5 R A 2 9 E M 2 3 1 A 7 D 1 5 R A 2 9 F M 2 3 1
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5 1 0 . 6 7 6 . 1 0
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 1 8 R A 2 9 A M 2 3 1 A 7 D 1 8 R A 2 9 C M 2 3 1 A 7 D 1 8 R A 2 9 E M 2 3 1 A 7 D 1 8 R A 2 9 F M 2 3 1
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8 1 0 . 6 7 6 . 1 0
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 2 2 R A 2 9 A M 2 3 1 A 7 D 2 2 R A 2 9 C M 2 3 1 A 7 D 2 2 R A 2 9 E M 2 3 1 A 7 D 2 2 R A 2 9 F M 2 3 1
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8 1 0 . 6 7 6 . 1 0
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 0 . 4 2 0 0 . 2 4 0
A 7 D 2 5 R A 2 9 A M 2 3 1 A 7 D 2 5 R A 2 9 C M 2 3 1 A 7 D 2 5 R A 2 9 E M 2 3 1 A 7 D 2 5 R A 2 9 F M 2 3 1
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0 1 0 . 6 7 6 . 1 0
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 0 . 4 2 0 0 . 2 4 0
A 7 D 2 8 R A 2 9 A M 2 3 1 A 7 D 2 8 R A 2 9 C M 2 3 1 A 7 D 2 8 R A 2 9 E M 2 3 1 A 7 D 2 8 R A 2 9 F M 2 3 1
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3 1 0 . 6 7 6 . 1 0
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 3 0 R A 2 9 A M 2 3 1 A 7 D 3 0 R A 2 9 C M 2 3 1 A 7 D 3 0 R A 2 9 E M 2 3 1 A 7 D 3 0 R A 2 9 F M 2 3 1
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8 1 0 . 6 7 6 . 1 0
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 0 . 4 2 0 0 . 2 4 0
A 7 D 3 5 R A 2 9 A M 2 3 1 A 7 D 3 5 R A 2 9 C M 2 3 1 A 7 D 3 5 R A 2 9 E M 2 3 1 A 7 D 3 5 R A 2 9 F M 2 3 1
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5 1 0 . 6 7 6 . 1 0
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 0 . 4 2 0 0 . 2 4 0
A 7 D 3 6 R A 2 9 A M 2 3 1 A 7 D 3 6 R A 2 9 C M 2 3 1 A 7 D 3 6 R A 2 9 E M 2 3 1 A 7 D 3 6 R A 2 9 F M 2 3 1
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3 1 0 . 6 7 6 . 1 0
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 0 . 4 2 0 0 . 2 4 0
A 7 D 4 0 R A 2 9 A M 2 3 1 A 7 D 4 0 R A 2 9 C M 2 3 1 A 7 D 4 0 R A 2 9 E M 2 3 1 A 7 D 4 0 R A 2 9 F M 2 3 1
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3 1 0 . 6 7 6 . 1 0
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 0 . 4 2 0 0 . 2 4 0
A 7 D 4 3 R A 2 9 A M 2 3 1 A 7 D 4 3 R A 2 9 C M 2 3 1 A 7 D 4 3 R A 2 9 E M 2 3 1 A 7 D 4 3 R A 2 9 F M 2 3 1
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5 1 0 . 6 7 6 . 1 0
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 0 . 4 2 0 0 . 2 4 0
A 7 D 5 0 R A 2 9 A M 2 3 1 A 7 D 5 0 R A 2 9 C M 2 3 1 A 7 D 5 0 R A 2 9 E M 2 3 1 A 7 D 5 0 R A 2 9 F M 2 3 1
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8 1 0 . 6 7 6 . 1 0
.200" [5.08] Row-to-Row (Dim. “H”) Spacing
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 0 6 R A 2 9 A M 2 3 2 A 7 D 0 6 R A 2 9 C M 2 3 2 A 7 D 0 6 R A 2 9 E M 2 3 2 A 7 D 0 6 R A 2 9 F M 2 3 2
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8 1 1 . 9 4 7 . 3 7
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 1 0 R A 2 9 A M 2 3 2 A 7 D 1 0 R A 2 9 C M 2 3 2 A 7 D 1 0 R A 2 9 E M 2 3 2 A 7 D 1 0 R A 2 9 F M 2 3 2
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8 1 1 . 9 4 7 . 3 7
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 0 . 4 7 0 0 . 2 9 0
A 7 D 1 5 R A 2 9 A M 2 3 2 A 7 D 1 5 R A 2 9 C M 2 3 2 A 7 D 1 5 R A 2 9 E M 2 3 2 A 7 D 1 5 R A 2 9 F M 2 3 2
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5 1 1 . 9 4 7 . 3 7
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 1 8 R A 2 9 A M 2 3 2 A 7 D 1 8 R A 2 9 C M 2 3 2 A 7 D 1 8 R A 2 9 E M 2 3 2 A 7 D 1 8 R A 2 9 F M 2 3 2
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8 1 1 . 9 4 7 . 3 7
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 2 2 R A 2 9 A M 2 3 2 A 7 D 2 2 R A 2 9 C M 2 3 2 A 7 D 2 2 R A 2 9 E M 2 3 2 A 7 D 2 2 R A 2 9 F M 2 3 2
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8 1 1 . 9 4 7 . 3 7
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 0 . 4 7 0 0 . 2 9 0
A 7 D 2 5 R A 2 9 A M 2 3 2 A 7 D 2 5 R A 2 9 C M 2 3 2 A 7 D 2 5 R A 2 9 E M 2 3 2 A 7 D 2 5 R A 2 9 F M 2 3 2
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0 1 1 . 9 4 7 . 3 7
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 0 . 4 7 0 0 . 2 9 0
A 7 D 2 8 R A 2 9 A M 2 3 2 A 7 D 2 8 R A 2 9 C M 2 3 2 A 7 D 2 8 R A 2 9 E M 2 3 2 A 7 D 2 8 R A 2 9 F M 2 3 2
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3 1 1 . 9 4 7 . 3 7
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 3 0 R A 2 9 A M 2 3 2 A 7 D 3 0 R A 2 9 C M 2 3 2 A 7 D 3 0 R A 2 9 E M 2 3 2 A 7 D 3 0 R A 2 9 F M 2 3 2
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8 1 1 . 9 4 7 . 3 7
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 0 . 4 7 0 0 . 2 9 0
A 7 D 3 5 R A 2 9 A M 2 3 2 A 7 D 3 5 R A 2 9 C M 2 3 2 A 7 D 3 5 R A 2 9 E M 2 3 2 A 7 D 3 5 R A 2 9 F M 2 3 2
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5 1 1 . 9 4 7 . 3 7
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 0 . 4 7 0 0 . 2 9 0
A 7 D 3 6 R A 2 9 A M 2 3 2 A 7 D 3 6 R A 2 9 C M 2 3 2 A 7 D 3 6 R A 2 9 E M 2 3 2 A 7 D 3 6 R A 2 9 F M 2 3 2
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3 1 1 . 9 4 7 . 3 7
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 0 . 4 7 0 0 . 2 9 0
A 7 D 4 0 R A 2 9 A M 2 3 2 A 7 D 4 0 R A 2 9 C M 2 3 2 A 7 D 4 0 R A 2 9 E M 2 3 2 A 7 D 4 0 R A 2 9 F M 2 3 2
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3 1 1 . 9 4 7 . 3 7
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 0 . 4 7 0 0 . 2 9 0
A 7 D 4 3 R A 2 9 A M 2 3 2 A 7 D 4 3 R A 2 9 C M 2 3 2 A 7 D 4 3 R A 2 9 E M 2 3 2 A 7 D 4 3 R A 2 9 F M 2 3 2
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5 1 1 . 9 4 7 . 3 7
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 0 . 4 7 0 0 . 2 9 0
A 7 D 5 0 R A 2 9 A M 2 3 2 A 7 D 5 0 R A 2 9 C M 2 3 2 A 7 D 5 0 R A 2 9 E M 2 3 2 A 7 D 5 0 R A 2 9 F M 2 3 2
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8 1 1 . 9 4 7 . 3 7
52
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
52
Ordering Information
.125" [3.18] Centerline / .250" [6.35] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l ABCDEM o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t Ear Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
.250" [6.35] Row-to-Row (Dim. “H”) Spacing
61 . 5 5 5 1 . 2 9 5 1 . 0 3 5 0 . 8 7 5 0 . 6 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 0 6 R A 2 9 A A 7 D 0 6 R A 2 9 C A 7 D 0 6 R A 2 9 E A 7 D 0 6 R A 2 9 F
3 9 . 5 0 3 2 . 8 9 2 6 . 2 9 2 2 . 2 3 1 5 . 8 8 1 3 . 2 1 8 . 6 4
1 0 2 . 0 5 5 1 . 7 9 5 1 . 5 3 5 1 . 3 7 5 1 . 1 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 1 0 R A 2 9 A A 7 D 1 0 R A 2 9 C A 7 D 1 0 R A 2 9 E A 7 D 1 0 R A 2 9 F
5 2 . 2 0 4 5 . 5 9 3 8 . 9 9 3 4 . 9 3 2 8 . 5 8 1 3 . 2 1 8 . 6 4
1 5 2 . 6 8 0 2 . 4 2 0 2 . 1 6 0 2 . 0 0 0 1 . 7 5 0 0 . 5 2 0 0 . 3 4 0 A 7 D 1 5 R A 2 9 A A 7 D 1 5 R A 2 9 C A 7 D 1 5 R A 2 9 E A 7 D 1 5 R A 2 9 F
6 8 . 0 7 6 1 . 4 7 5 4 . 8 6 5 0 . 8 0 4 4 . 4 5 1 3 . 2 1 8 . 6 4
1 8 3 . 0 5 5 2 . 7 9 5 2 . 5 3 5 2 . 3 7 5 2 . 1 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 1 8 R A 2 9 A A 7 D 1 8 R A 2 9 C A 7 D 1 8 R A 2 9 E A 7 D 1 8 R A 2 9 F
7 7 . 6 0 7 0 . 9 9 6 4 . 3 9 6 0 . 3 3 5 3 . 9 8 1 3 . 2 1 8 . 6 4
2 2 3 . 5 5 5 3 . 2 9 5 3 . 0 3 5 2 . 8 7 5 2 . 6 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 2 2 R A 2 9 A A 7 D 2 2 R A 2 9 C A 7 D 2 2 R A 2 9 E A 7 D 2 2 R A 2 9 F
9 0 . 3 0 8 3 . 6 9 7 7 . 0 9 7 3 . 0 3 6 6 . 6 8 1 3 . 2 1 8 . 6 4
2 5 3 . 9 3 0 3 . 6 7 0 3 . 4 1 0 3 . 2 5 0 3 . 0 0 0 0 . 5 2 0 0 . 3 4 0 A 7 D 2 5 R A 2 9 A A 7 D 2 5 R A 2 9 C A 7 D 2 5 R A 2 9 E A 7 D 2 5 R A 2 9 F
9 9 . 8 2 9 3 . 2 2 8 6 . 6 1 8 2 . 5 5 7 6 . 2 0 1 3 . 2 1 8 . 6 4
2 8 4 . 3 0 5 4 . 0 4 5 3 . 7 8 5 3 . 6 2 5 3 . 3 7 5 0 . 5 2 0 0 . 3 4 0 A 7 D 2 8 R A 2 9 A A 7 D 2 8 R A 2 9 C A 7 D 2 8 R A 2 9 E A 7 D 2 8 R A 2 9 F
1 0 9 . 3 5 1 0 2 . 7 4 9 6 . 1 4 9 2 . 0 8 8 5 . 7 3 1 3 . 2 1 8 . 6 4
3 0 4 . 5 5 5 4 . 2 9 5 4 . 0 3 5 3 . 8 7 5 3 . 6 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 3 0 R A 2 9 A A 7 D 3 0 R A 2 9 C A 7 D 3 0 R A 2 9 E A 7 D 3 0 R A 2 9 F
1 1 5 . 7 0 1 0 9 . 0 9 1 0 2 . 4 9 9 8 . 4 3 9 2 . 0 8 1 3 . 2 1 8 . 6 4
3 5 5 . 1 8 0 4 . 9 2 0 4 . 6 6 0 4 . 5 0 0 4 . 2 5 0 0 . 5 2 0 0 . 3 4 0 A 7 D 3 5 R A 2 9 A A 7 D 3 5 R A 2 9 C A 7 D 3 5 R A 2 9 E A 7 D 3 5 R A 2 9 F
1 3 1 . 5 7 1 2 4 . 9 7 1 1 8 . 3 6 1 1 4 . 3 0 1 0 7 . 9 5 1 3 . 2 1 8 . 6 4
3 6 5 . 3 0 5 5 . 0 4 5 4 . 7 8 5 4 . 6 2 5 4 . 3 7 5 0 . 5 2 0 0 . 3 4 0 A 7 D 3 6 R A 2 9 A A 7 D 3 6 R A 2 9 C A 7 D 3 6 R A 2 9 E A 7 D 3 6 R A 2 9 F
1 3 4 . 7 5 1 2 8 . 1 4 1 2 1 . 5 4 1 1 7 . 4 8 1 1 1 . 1 3 1 3 . 2 1 8 . 6 4
4 0 5 . 8 0 5 5 . 5 4 5 5 . 2 8 5 5 . 1 2 5 4 . 8 7 5 0 . 5 2 0 0 . 3 4 0 A 7 D 4 0 R A 2 9 A A 7 D 4 0 R A 2 9 C A 7 D 4 0 R A 2 9 E A 7 D 4 0 R A 2 9 F
1 4 7 . 4 5 1 4 0 . 8 4 1 3 4 . 2 4 1 3 0 . 1 8 1 2 3 . 8 3 1 3 . 2 1 8 . 6 4
4 3 6 . 1 8 0 5 . 9 2 0 5 . 6 6 0 5 . 5 0 0 5 . 2 5 0 0 . 5 2 0 0 . 3 4 0 A 7 D 4 3 R A 2 9 A A 7 D 4 3 R A 2 9 C A 7 D 4 3 R A 2 9 E A 7 D 4 3 R A 2 9 F
1 5 6 . 9 7 1 5 0 . 3 7 1 4 3 . 7 6 1 3 9 . 7 0 1 3 3 . 3 5 1 3 . 2 1 8 . 6 4
5 0 7 . 0 5 5 6 . 7 9 5 6 . 5 3 5 6 . 3 7 5 6 . 1 2 5 0 . 5 2 0 0 . 3 4 0 A 7 D 5 0 R A 2 9 A A 7 D 5 0 R A 2 9 C A 7 D 5 0 R A 2 9 E A 7 D 5 0 R A 2 9 F
1 7 9 . 2 0 1 7 2 . 5 9 1 6 5 . 9 9 1 6 1 . 9 3 1 5 5 . 5 8 1 3 . 2 1 8 . 6 4
53
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Modified Bellows Connectors, .156 x .200 [3.96 x 5.08] Centerline, Straight
Dip Solder and Wire Wrap Ta i l s
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—
5000 megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1500 VDC
(sea level)
Current Rating—3 Amperes
Initial Contact Resistance—
10 milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern—
page 57
Mounting Styles
SECTION X-X
ROTATED 90º
SECTION X-X
.610
[5.49]
.200
[5.08]
.368
[9.35]
.025
[.64] Sq.
.156
[3.96] Ref.
.250
[6.35]
.156
[3.25]
.200
[5.08]
P±.003 [.08] Dia.
.054±.071
[1.37±1.890 ] PC Board
.300
[7.62] Card Depth
P=.040 [1.02] Dip Solder Applications
P=.042 [1.07] For Wire Wrap Applications
Dim B
A
B
E
D
J
C
Dim E
.180
[4.57]
.610
[15.49] Ref.
.128
[3.25] Dia.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
4-40 Threaded Insert No Mounting Ears
54
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
54
Ordering Information
.156" [3.96] Centerline / .200" [5.08] Row-to-Row Mounting Ear Options
No. of D i m e n s i o n s C e n t e r e d C e n t e r e d N o
D u a l Mounting Ear Mounting Ear M o u n t i n g
R e a d o u t ABCDE .125" [3.18] Thru 4-40 Threaded E a r s
P o s i t i o n s H o l e I n s e r t
Tail Length .160" [4.06] (DIM “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 A 6 D 0 6 D S 2 9 A 2 A 6 D 0 6 D S 2 9 B 2 A 6 D 0 6 D S 2 9 C 2
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 A 6 D 1 0 D S 2 9 A 2 A 6 D 1 0 D S 2 9 B 2 A 6 D 1 0 D S 2 9 C 2
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 A 6 D 1 2 D S 2 9 A 2 A 6 D 1 2 D S 2 9 B 2 A 6 D 1 2 D S 2 9 C 2
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 A 6 D 1 5 D S 2 9 A 2 A 6 D 1 5 D S 2 9 B 2 A 6 D 1 5 D S 2 9 C 2
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 A 6 D 1 8 D S 2 9 A 2 A 6 D 1 8 D S 2 9 B 2 A 6 D 1 8 D S 2 9 C 2
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 A 6 D 2 2 D S 2 9 A 2 A 6 D 2 2 D S 2 9 B 2 A 6 D 2 2 D S 2 9 C 2
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 A 6 D 2 5 D S 2 9 A 2 A 6 D 2 5 D S 2 9 B 2 A 6 D 2 5 D S 2 9 C 2
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 A 6 D 2 8 D S 2 9 A 2 A 6 D 2 8 D S 2 9 B 2 A 6 D 2 8 D S 2 9 C 2
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 A 6 D 3 6 D S 2 9 A 2 A 6 D 3 6 D S 2 9 B 2 A 6 D 3 6 D S 2 9 C 2
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 A 6 D 4 3 D S 2 9 A 2 A 6 D 4 3 D S 2 9 B 2 A 6 D 4 3 D S 2 9 C 2
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
Tail Length .220" [5.59] (DIM “J”)
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 A 6 D 0 6 D S 2 9 A 3 A 6 D 0 6 D S 2 9 B 3 A 6 D 0 6 D S 2 9 C 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 A 6 D 1 0 D S 2 9 A 3 A 6 D 1 0 D S 2 9 B 3 A 6 D 1 0 D S 2 9 C 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 A 6 D 1 2 D S 2 9 A 3 A 6 D 1 2 D S 2 9 B 3 A 6 D 1 2 D S 2 9 C 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 A 6 D 1 5 D S 2 9 A 3 A 6 D 1 5 D S 2 9 B 3 A 6 D 1 5 D S 2 9 C 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 A 6 D 1 8 D S 2 9 A 3 A 6 D 1 8 D S 2 9 B 3 A 6 D 1 8 D S 2 9 C 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 A 6 D 2 2 D S 2 9 A 3 A 6 D 2 2 D S 2 9 B 3 A 6 D 2 2 D S 2 9 C 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 A 6 D 2 5 D S 2 9 A 3 A 6 D 2 5 D S 2 9 B 3 A 6 D 2 5 D S 2 9 C 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 A 6 D 2 8 D S 2 9 A 3 A 6 D 2 8 D S 2 9 B 3 A 6 D 2 8 D S 2 9 C 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 A 6 D 3 6 D S 2 9 A 3 A 6 D 3 6 D S 2 9 B 3 A 6 D 3 6 D S 2 9 C 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 A 6 D 4 3 D S 2 9 A 3 A 6 D 4 3 D S 2 9 B 3 A 6 D 4 3 D S 2 9 C 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
Tail Length .560" [14.22] (DIM “J”) For Wire Wrap Termination
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 A 6 D 0 6 W W 2 9 A 3 A 6 D 0 6 W W 2 9 B 3 –
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 A 6 D 1 0 W W 2 9 A 3 A 6 D 1 0 W W 2 9 B 3 –
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 A 6 D 1 2 W W 2 9 A 3 A 6 D 1 2 W W 2 9 B 3 –
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 A 6 D 1 5 W W 2 9 A 3 A 6 D 1 5 W W 2 9 B 3 –
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 A 6 D 1 8 W W 2 9 A 3 A 6 D 1 8 W W 2 9 B 3 –
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 A 6 D 2 2 W W 2 9 A 3 A 6 D 2 2 W W 2 9 B 3 –
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 A 6 D 2 5 W W 2 9 A 3 A 6 D 2 5 W W 2 9 B 3 –
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 A 6 D 2 8 W W 2 9 A 3 A 6 D 2 8 W W 2 9 B 3 –
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 A 6 D 3 6 W W 2 9 A 3 A 6 D 3 6 W W 2 9 B 3 –
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 A 6 D 4 3 W W 2 9 A 3 A 6 D 4 3 W W 2 9 B 3 –
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2
55
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Product Facts
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E60980
■Certified
by Canadian
Standards
Association,
File No. LR49571
Physical Properties:
Insulation Resistance—5000
megohms minimum.
Insertion/Withdrawal Force
(Daughter Card)—8 oz./2 oz.
[35.6 N/ 8.9 N] average contact pair
using .0620 [1.57] steel blade.
Insulator Body—Glass filled
thermoplastic, UL rating 94V-O. High
temp. plastic option is available; add
suffix M399 to part number.
Color—Black
Contacts—High strength copper alloy.
Contact Plating—.000050 [0.00127]
nickel underplate with .000030
[0.00076] gold in the mating area,
tin/lead on tails, .000100 [0.00254]
minimum
Electrical Properties:
Operation Voltage—1500 VDC (sea
level)
Current Rating—3 Amperes
Initial Contact Resistance—10
milliohms
Environmental Properties:
Operating Temperature—
-55˚C to +125˚C
Temperature Cycling—
MIL-STD-202 method 107
Vibration—MIL-STD-202 method 204
Related Product Data:
Polarization Key—page 57
Daughter Card Edge Pattern—
page 57
Mounting Styles
SECTION X-X
ROTATED 90º
Modified Bellows Connectors .156 x .200 [3.96 x 5.08] Centerline, .156 x .150
[3.96 x 3.81], Right Angle, Dip Solder Ta i l s
.156
[3.96] REF
SECTION X-X
.180
[4.57]
.250
[6.35] .250
[6.35]
.610
[15.49] Ref. .610
[15.49] Ref. .610
[15.49] Ref.
Centered Mounting Ear
.125 [3.18] Thru Hole Centered Mounting Ear
.125 [3.18] Thru Hole Flush Mounting Ear
.125 [3.18] Cross
Drilled Hole
No Mounting Ears
Dim G - Centered Mounting Ear .125 [3.18] Cross Drilled Hole Only
Dim K - Flush Mounting Ear .125 [3.18] Cross Drilled Hole Only
.14±.01
[3.56±.25]
H
C
D
E
B
A
.025
[.64] Sq. Typ.
.156
[3.96]
.368
[9.35]
.040±.003
[1.02±.08] Dia.
Dim G
Dim K
Dim B
Dim E
Dim H
Row to Row Spacing
.128
[3.25] Dia.
.054±.071
[1.37±1.890] PC Board
56
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
56
Ordering Information
.156" [3.96] Centerline / .200" [5.08] and .150" [3.81] Row-to-Row (Dim. “H”) Spacing
D i m e n s i o n s Mounting Ear Options
No. of C e n t e r e d F l u s h C e n t e r e d N o C e n t e r e d F l u s h
D u a l ABCDEM o u n t i n g M o u n t i n g Mounting Ear M o u n t i n g Mounting Ear Mounting Ear
R e a d o u t Ear Only Ear Only .125" [3.18] E a r s .125" [3.18] .125" [3.18]
P o s i t i o n s G K Thru Hole Cross-Drilled Hole Cross-Drilled Hole
.200" [5.08] Row-to-Row (Dim. “H”) Spacing
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 0 . 4 7 0 0 . 2 9 0 A 6 D 0 6 R A 2 9 A A 6 D 0 6 R A 2 9 C A 6 D 0 6 R A 2 9 E A 6 D 0 6 R A 2 9 F
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1 1 1 . 9 4 7 . 3 7
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 0 . 4 7 0 0 . 2 9 0 A 6 D 1 0 R A 2 9 A A 6 D 1 0 R A 2 9 C A 6 D 1 0 R A 2 9 E A 6 D 1 0 R A 2 9 F
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6 1 1 . 9 4 7 . 3 7
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 0 . 4 7 0 0 . 2 9 0 A 6 D 1 2 R A 2 9 A A 6 D 1 2 R A 2 9 C A 6 D 1 2 R A 2 9 E A 6 D 1 2 R A 2 9 F
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9 1 1 . 9 4 7 . 3 7
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 0 . 4 7 0 0 . 2 9 0 A 6 D 1 5 R A 2 9 A A 6 D 1 5 R A 2 9 C A 6 D 1 5 R A 2 9 E A 6 D 1 5 R A 2 9 F
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7 1 1 . 9 4 7 . 3 7
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 0 . 4 7 0 0 . 2 9 0 A 6 D 1 8 R A 2 9 A A 6 D 1 8 R A 2 9 C A 6 D 1 8 R A 2 9 E A 6 D 1 8 R A 2 9 F
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6 1 1 . 9 4 7 . 3 7
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 0 . 4 7 0 0 . 2 9 0 A 6 D 2 2 R A 2 9 A A 6 D 2 2 R A 2 9 C A 6 D 2 2 R A 2 9 E A 6 D 2 2 R A 2 9 F
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1 1 1 . 9 4 7 . 3 7
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 0 . 4 7 0 0 . 2 9 0 A 6 D 2 5 R A 2 9 A A 6 D 2 5 R A 2 9 C A 6 D 2 5 R A 2 9 E A 6 D 2 5 R A 2 9 F
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0 1 1 . 9 4 7 . 3 7
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 0 . 4 7 0 0 . 2 9 0 A 6 D 2 8 R A 2 9 A A 6 D 2 8 R A 2 9 C A 6 D 2 8 R A 2 9 E A 6 D 2 8 R A 2 9 F
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8 1 1 . 9 4 7 . 3 7
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 0 . 4 7 0 0 . 2 9 0 A 6 D 3 6 R A 2 9 A A 6 D 3 6 R A 2 9 C A 6 D 3 6 R A 2 9 E A 6 D 3 6 R A 2 9 F
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8 1 1 . 9 4 7 . 3 7
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 4 0 . 4 7 0 0 . 2 9 0 A 6 D 4 0 R A 2 9 A A 6 D 4 0 R A 2 9 C A 6 D 4 0 R A 2 9 E A 6 D 4 0 R A 2 9 F
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 2 1 3 . 4 6 1 5 4 . 5 3 1 1 . 9 4 7 . 3 7
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 0 . 4 7 0 0 . 2 9 0 A 6 D 4 3 R A 2 9 A A 6 D 4 3 R A 2 9 C A 6 D 4 3 R A 2 9 E A 6 D 4 3 R A 2 9 F
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2 1 1 . 9 4 7 . 3 7
.150" [3.81] Row-to-Row (Dim. “H”) Spacing
61 . 7 8 4 1 . 5 3 4 1 . 2 2 1 1 . 1 0 0 0 . 7 8 0 0 . 4 2 0 0 . 2 4 0
A 6 D 0 6 R A 2 9 A M 2 3 3 A 6 D 0 6 R A 2 9 C M 2 3 3 A 6 D 0 6 R A 2 9 E M 2 3 3 A 6 D 0 6 R A 2 9 F M 2 3 3
4 5 . 3 1 3 8 . 9 6 3 1 . 0 1 2 7 . 9 4 1 9 . 8 1 1 0 . 6 7 6 . 1 0
1 0 2 . 4 0 8 2 . 1 5 8 1 . 8 4 5 1 . 7 2 4 1 . 4 0 4 0 . 4 2 0 0 . 2 4 0
A 6 D 1 0 R A 2 9 A M 2 3 3 A 6 D 1 0 R A 2 9 C M 2 3 3 A 6 D 1 0 R A 2 9 E M 2 3 3 A 6 D 1 0 R A 2 9 F M 2 3 3
6 1 . 1 6 5 4 . 8 1 4 6 . 8 6 4 3 . 7 9 3 5 . 6 6 1 0 . 6 7 6 . 1 0
1 2 2 . 7 2 0 2 . 4 7 0 2 . 1 5 7 2 . 0 3 6 1 . 7 1 6 0 . 4 2 0 0 . 2 4 0
A 6 D 1 2 R A 2 9 A M 2 3 3 A 6 D 1 2 R A 2 9 C M 2 3 3 A 6 D 1 2 R A 2 9 E M 2 3 3 A 6 D 1 2 R A 2 9 F M 2 3 3
6 9 . 0 9 6 2 . 7 4 5 4 . 7 9 5 1 . 7 1 4 3 . 5 9 1 0 . 6 7 6 . 1 0
1 5 3 . 1 8 8 2 . 9 3 8 2 . 6 2 5 2 . 5 0 4 2 . 1 8 4 0 . 4 2 0 0 . 2 4 0
A 6 D 1 5 R A 2 9 A M 2 3 3 A 6 D 1 5 R A 2 9 C M 2 3 3 A 6 D 1 5 R A 2 9 E M 2 3 3 A 6 D 1 5 R A 2 9 F M 2 3 3
8 0 . 9 8 7 4 . 6 3 6 6 . 6 8 6 3 . 6 0 5 5 . 4 7 1 0 . 6 7 6 . 1 0
1 8 3 . 6 5 6 3 . 4 0 6 3 . 0 9 3 2 . 9 7 2 2 . 6 5 2 0 . 4 2 0 0 . 2 4 0
A 6 D 1 8 R A 2 9 A M 2 3 3 A 6 D 1 8 R A 2 9 C M 2 3 3 A 6 D 1 8 R A 2 9 E M 2 3 3 A 6 D 1 8 R A 2 9 F M 2 3 3
9 2 . 8 6 8 6 . 5 1 7 8 . 5 6 7 5 . 4 9 6 7 . 3 6 1 0 . 6 7 6 . 1 0
2 2 4 . 2 8 0 4 . 0 3 0 3 . 7 1 7 3 . 5 9 6 3 . 2 7 6 0 . 4 2 0 0 . 2 4 0
A 6 D 2 2 R A 2 9 A M 2 3 3 A 6 D 2 2 R A 2 9 C M 2 3 3 A 6 D 2 2 R A 2 9 E M 2 3 3 A 6 D 2 2 R A 2 9 F M 2 3 3
1 0 8 . 7 1 1 0 2 . 3 6 9 4 . 4 1 9 1 . 3 4 8 3 . 2 1 1 0 . 6 7 6 . 1 0
2 5 4 . 7 4 8 4 . 4 9 8 4 . 1 8 5 4 . 0 6 4 3 . 7 4 4 0 . 4 2 0 0 . 2 4 0
A 6 D 2 5 R A 2 9 A M 2 3 3 A 6 D 2 5 R A 2 9 C M 2 3 3 A 6 D 2 5 R A 2 9 E M 2 3 3 A 6 D 2 5 R A 2 9 F M 2 3 3
1 2 0 . 6 0 1 1 4 . 2 5 1 0 6 . 3 0 1 0 3 . 2 3 9 5 . 1 0 1 0 . 6 7 6 . 1 0
2 8 5 . 2 1 6 4 . 9 6 6 4 . 6 5 3 4 . 5 3 2 4 . 2 1 2 0 . 4 2 0 0 . 2 4 0
A 6 D 2 8 R A 2 9 A M 2 3 3 A 6 D 2 8 R A 2 9 C M 2 3 3 A 6 D 2 8 R A 2 9 E M 2 3 3 A 6 D 2 8 R A 2 9 F M 2 3 3
1 3 2 . 4 9 1 2 6 . 1 4 1 1 8 . 1 9 1 1 5 . 1 1 1 0 6 . 9 8 1 0 . 6 7 6 . 1 0
3 6 6 . 4 6 4 6 . 2 1 4 5 . 9 0 1 5 . 7 8 0 5 . 4 6 0 0 . 4 2 0 0 . 2 4 0
A 6 D 3 6 R A 2 9 A M 2 3 3 A 6 D 3 6 R A 2 9 C M 2 3 3 A 6 D 3 6 R A 2 9 E M 2 3 3 A 6 D 3 6 R A 2 9 F M 2 3 3
1 6 4 . 1 9 1 5 7 . 8 4 1 4 9 . 8 9 1 4 6 . 8 1 1 3 8 . 6 8 1 0 . 6 7 6 . 1 0
4 0 7 . 0 8 8 6 . 8 3 8 6 . 5 2 5 6 . 4 0 4 6 . 0 8 4 0 . 4 2 0 0 . 2 4 0
A 6 D 4 0 R A 2 9 A M 2 3 3 A 6 D 4 0 R A 2 9 C M 2 3 3 A 6 D 4 0 R A 2 9 E M 2 3 3 A 6 D 4 0 R A 2 9 F M 2 3 3
1 8 0 . 0 4 1 7 3 . 6 9 1 6 5 . 7 4 1 6 2 . 6 6 1 5 4 . 5 3 1 0 . 6 7 6 . 1 0
4 3 7 . 5 5 6 7 . 3 0 6 6 . 9 9 3 6 . 8 7 2 6 . 5 5 2 0 . 4 2 0 0 . 2 4 0
A 6 D 4 3 R A 2 9 A M 2 3 3 A 6 D 4 3 R A 2 9 C M 2 3 3 A 6 D 4 3 R A 2 9 E M 2 3 3 A 6 D 4 3 R A 2 9 F M 2 3 3
1 9 1 . 9 2 1 8 5 . 5 7 1 7 7 . 6 2 1 7 4 . 5 5 1 6 6 . 4 2 1 0 . 6 7 6 . 1 0
57
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Card Edge Polarization Keys
Description/Application
Tyco Electronics can pro-
vide polarization keys in the
basic configuration shown
on this page. Our Modified
Bellows and Cantilever
Beam Series Card Edge
Connectors use these keys.
The part number and the
connector series for which it
was designed are listed in
the table below.
Ordering Information
Acquired Part Used on Connector Shown on
Number Series Pages
98014-01 Modified Bellows 41-56
98014-01 Cantilever Beam 28-40
.24
[6.10]
45°
Break Off Point
.19
[4.83]
.033
[.84]
Daughter Card
Contact Spacing Dim A Dim B
Non-Accum. ±.005 (.13)
.100 [2.54] .093 [2.36] .052 [1.32]
.125 [3.18] .093 [2.36] .052 [1.32]
.156 [3.96] .105* [2.67] .094 [2.39]
* Except MIL-C-21097E 8–4 which is .070 [1.78]
NOTES:
1. Dimensions are in inches
2. Unless otherwise specified, tolerance is ±.005 [0.13 mm] for three place
decimals.
3. Number of contact fingers shall be the same as the corresponding printed
wiring connector.
.062 [1.57]
Board Thickness
Slot Depth
Min.
Dim. A (Per Applicable Catalog Page)
Dim. B
Contact Spacing
See Note 3
Per MIL-C-21097E
.015
[.38]
30°
Card Edge Connectors Recommended Daughter Card Edge Pattern
58
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
58
Low Profile Connectors
For printed circuit board
packaging, AMP Low Profile
Edge Connectors provide
high performance, low cost
connections on .125 [3.18]
and .156 [3.96] centerline
spacings. .100 [2.54] cen-
terline connectors can be
made available, consult
Tyco Electronics.
Mounted connector hous-
ings extend only .460
[11.68] from the mother
board to allow efficient use
of available space.
These low profile connec-
tors are available in 6
through 43 dual position
sizes on .156 [3.96] center-
line spacing and with 6
through 50 dual positions
on .125 [3.18] centers.
Connectors are supplied
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Product Facts
■Low profile housing is .460
[11.68] deep
■6 through 43 dual positions
on .156 [3.96] centerline;
6 though 50 dual positions
on .125 [3.18] centerline
■Solder eyelet for wire-to-
board or solder post for
mother-daughter board
application
■Selective gold plating of
contact area for high
performance at low cost
■Alternate platings are
available on request
■Contacts bifurcated for
redundancy
■Tin plate for high solder-
ability of solder eyelets
and posts
■Accepts .055-.070 [1.40-
1.78] thick printed circuit
boards
■Housings available with or
without mounting ears
■Intercontact keying
available
■UL 94V-0 rated, glass-filled
polyester housings
■Variety of solder post
lengths
■5 ampere current rating
per contact*
■Recognized under the
Component Program of
Underwriters
Laboratories Inc.
File No. E28476
with either solder posts for
mother-daughter board
applications or solder eye-
let contacts for wire-to-
board use.
Low Profile Edge Connec-
tors feature clear slot entry
and accept .055-.070
[1.40-1.78] thick double-
sided printed circuit boards.
Solder posts are available
with .150 [3.18] and .180
[4.57] long tails on .140
[3.56] or .200 [5.08] row-
to-row spacing.
Impact-resistant thermo-
plastic housing, UL rated
94V-0, have molded-in
cavity identification and are
available with or without
mounting ears. Additional
features of the housings
include intercontact keying
provisions, probe slots and
identification of number one
position.
The precision formed con-
tacts made of phosphor
bronze are gold plated on
the contact mating surface
only. This selective plating
provides high reliability
while maintaining low cost.
Solder eyelets and posts
are tin plated for excellent
solderability. The contact is
bifurcated for redundancy.
Shorting contacts are
available.
All connector configurations
are furnished preloaded.
Selectively loaded connec-
tors can be made available
for added economy.
59
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Low Profile Connectors, .125 [3.18] Centerline
Material and Finish:
Housing—Green, glass-filled
polyester
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] gold in con-
tact area; .000100 [0.00254] bright tin
on posts, with entire contact under-
plated .000030 [0.00076] nickel
Related Product Data:
Keying Plug—page 63
PC Board Hole Layouts—See below
PC Board Edge Pattern—page 63
Technical Documents:
(pages 186, 187):
Product Specification
108-9044
Instruction Sheet 408-7772
Flow Solder Post
.200 [5.08] Row-to-Row Spacing
Recommended
PC Board Hole Layout Recommended
PC Board Hole Layout
Flow Solder Post
.140 [3.56] Row-to-Row Spacing Solder Eyelet Contact
.235 [5.97] Row-to-Row Spacing
.300
[7.62]
.150
[3.81]
.460
[11.68]
.250
[6.35]
.295
[7.49]
.165
[4.19]
.140
[3.56]
.140
[3.56]
.070
[1.78]
.125
[3.18]
.200
[5.08]
.100
[2.54]
.125
[3.18]
.200
[5.08]
.295
[7.49]
.295
[7.49]
.165
[4.19]
.165
[4.19]
.125
[3.18]
A
B
D
B
B
E
C
.125
[3.18] Typ.
. 1 2 5
[3.18] R e f .
.128
[3.25] Dia. .052
[1.32] Dia. .128
[3.25] Dia. .052
[1.32] Dia.
.335
[8.51]
Typ.
.335
[8.51]
Typ.
. 1 2 5
[3.18] R e f . . 1 2 5
[3.18] R e f .
.280
[7.11] Ref.
.235
[5.97] Ref.
.125
[3.18] Typ.
Molded Characters (Upper and Lower Case
Letters Omitting Letters G, I, O &Q)
#1 Cavity Identification
Post Length
(See Chart)
Post Length
(See Chart)
.128
[3.25] Dia.
2 (Plcs.)
PCBoard Thickness—
.055-.070 [1.40-1.78]
123 456
A B C D E F
60
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
60
Low Profile Connectors, .125 [3.18] Centerline (Continued)
Flow Solder Post
.200 [5.08] Row-to-Row
Spacing
No. of Dimensions Post With Without
Dual Mounting Mounting
Positions ABCDELength* Ears Ears
.875 .370 1.035
622.23 —9.40 26.29 —.150 — 2-530671-1
1.375 1.795 .370 1.535 2.055 .150 — 2-530671-2
10 34.93 45.59 9.40 38.99 52.20 .180 2-530663-2 —
2.000 2.420 .370 2.160 2.680
15 50.80 61.47 9.40 54.86 68.07 .150 — 2-530671-3
2.375 2.795 .370 2.535 3.055
18 60.33 70.99 9.40 64.39 77.60 .180 2-530663-4 2-530671-4
2.875 3.295 .370 3.035 3.555
22 73.03 83.69 9.40 77.09 90.30 .150 2-530662-5 2-530671-5
3.125 .370 3.285
24 79.38 —9.40 83.44 —.150 — 3-530671-3
3.625 4.045 .370 3.785 4.305
28 92.08 102.74 9.40 96.14 109.35 .150 2-530662-6 2-530671-6
3.875 .370 4.035
30 98.43 —9.40 102.49 —.150 — 2-530671-7
4.625 5.045 .370 4.785 5.305 .150 — 2-530671-9
36 117.48 128.14 9.40 121.54 134.75 .180 — 2-530672-9
5.125 5.545 .437 5.285 5.805
40 130.18 140.84 11.10 134.24 147.45 .150 — 3-530671-0
6.375 6.795 .437 6.535 7.055
50 161.93 172.59 11.10 165.99 179.20 .150 3-530662-2 —
Flow Solder Post
.140 [3.56] Row-to-Row
Spacing
Solder Eyelet Contact
.235 [5.97] Row-to-Row
Spacing
No. of Dimensions Post With Without
Dual Mounting Mounting
Positions ABCDELength* Ears Ears
2.000 .370 2.160 .150 — 2-530673-3
15 50.80 —9.40 54.86 —
3.625 .370 3.785 .150 — 2-530673-6
28 92.08 —9.40 96.14 —.180 2-530674-6 —
6.375 6.795 .437 6.535 7.055
50 161.93 172.59 11.10 165.99 179.20 .180 3-530659-2 —
No. of Dimensions With
Dual Mounting
Positions ABCDE Ears
2.000 2.420 .370 2.160 2.680
15 50.80 61.47 9.40 54.86 68.07 2-530664-3
2.875 3.295 .370 3.035 3.555
22 73.02 83.69 9.40 77.08 90.29 2-530664-5
3.625 4.045 .370 3.785 4.305
28 92.08 102.74 9.40 96.14 109.35 2-530664-6
5.125 5.545 .437 5.285 5.805
40 130.17 140.84 11.10 134.23 147.44 3-530664-0
6.375 6.795 .437 6.535 7.055
50 161.92 172.59 11.10 165.98 179.19 3-530664-2
*Metric equivalents for post length are .150 = [3.81]; .180 = [4.57].
Note: Other connector sizes can be made available, consult Tyco Electronics.
61
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Low Profile Connectors, .156 [3.96] Centerline
Material and Finish:
Housing—Green, glass-filled
polyester
Contacts—Phosphor bronze, duplex
plated .000030 [0.00076] gold in con-
tact area; .000100 [0.00254] bright tin
on posts, with entire contact under-
plated .000030 [0.00076] nickel
Insert—Brass
Mounting Ear
with Insert
.300
[7.62]
.150
[3.81]
A
B
D
E
C
.160
[4.06] .156
[3.96] Typ.
Molded Characters (Upper and Lower Case
Letters Omitting Letters G, I, O &Q)
#1 Cavity Identification
.128
[3.25] Dia.
(2 Plcs.)
PCBoard Thickness—
.055-.070 [1.40-1.78]
Threaded Inserts
4-40 NC-2B
(2 per connector)
.460
[11.68]
.250
[6.35]
.156
[3.96] Typ.
Flow Solder Post
.200 [5.08] Row-to-Row Spacing
Recommended
PC Board Hole Layout Recommended
PC Board Hole Layout
Flow Solder Post
.140 [3.56] Row-to-Row Spacing Solder Eyelet Contact
.235 [5.97] Row-to-Row Spacing
.295
[7.49]
.165
[4.19]
.140
[3.56]
.140
[3.56]
.070
[1.78]
.156
[3.96]
.200
[5.08]
.100
[2.54]
.156
[3.96]
.200
[5.08]
.295
[7.49]
.295
[7.49]
.165
[4.19]
.165
[4.19]
B
B
.125
[3.18] Ref.
.128
[3.25] Dia. .052
[1.32] Dia. .128
[3.25] Dia. .052
[1.32] Dia.
.378
[9.59]
Typ.
.378
[9.59]
Typ.
.125
[3.18] Ref. .125
[3.18] Ref.
.280
[7.11] Ref.
.235
[5.97] Ref.
Post Length
(See Chart)
Post Length
(See Chart)
Related Product Data:
Keying Plug—page 63
PC Board Hole Layouts—See below
PC Board Edge Pattern—page 63
Technical Documents:
(pages 186, 187):
Product Specification
108-9044
Instruction Sheet 408-7772
12 3 456
A B C D E F
62
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
62
Low Profile Connectors, .156 [3.96] Centerline (Continued)
Flow Solder Post
.200 [5.08] Row-to-Row
Spacing
No. of Dimensions Post With With Without
Dual Mounting Mounting Ears Mounting
Positions A B C D E Length* Ears and Inserts Ears
1.100 1.535 .370 1.240 1.785 2-530655-1 2-530677-1 —
627.94 38.99 9.40 31.50 45.34 .150 12-530689-11— 2-530666-1
1.724 2.159 .370 1.864 2.409 .150 2-530655-2 — 2-530666-2
10 43.79 54.84 9.40 47.35 61.19 .180 2-530656-2 — —
2.036 2.471 .370 2.176 2.721
12 51.71 62.76 9.40 55.27 69.11 .150 2-530655-3 — 2-530666-3
2.504 2.939 .370 2.644 3.189 2-530655-4 — 2-530666-4
15 63.60 74.65 9.40 67.16 81.00 .150 12-530689-41— —
2.972 3.407 .370 3.112 3.657 .150 2-530655-5 — 2-530666-5
18 75.49 86.54 9.40 79.04 92.89 .180 — — 2-530667-5
3.596 4.031 .370 3.736 4.281 2-530655-6 — 2-530666-6
22 .150 12-530689-61—12-531433-41
91.34 102.39 9.40 94.89 108.74 .180 2-530656-6 2-530678-6 2-530667-6
4.064 4.499 .370 4.204 4.749 .150 2-530655-8 — 12-531433-11
25 103.23 114.27 9.40 106.78 120.62 .180 2-530656-8 — 2-530666-8
4.532 4.967 .370 4.672 5.217 .150 3-530655-2 — 3-530666-2
28 115.11 126.16 9.40 118.67 132.51 .180 3-530656-2 — —
4.844 5.279 .437 4.984 5.529 .150 2-530655-9 — 2-530666-9
30 123.04 134.09 11.10 126.59 140.44 12-530689-91— —
.180 — — 2-530667-9
5.780 6.215 .437 5.920 6.465 .150 3-530655-0 — 12-531433-21
36 146.18 157.86 11.10 150.37 164.21 .180 13-530689-01— 2-530667-0
6.872 7.307 .437 7.012 7.557 .150 3-530655-3 3-530677-3 3-530666-3
43 174.55 185.60 11.10 178.10 191.95 .180 3-530656-3 — 3-530667-3
Flow Solder Post
.140 [3.56] Row-to-Row
Spacing
and
Solder Eyelet Contact
.235 [5.97] Row-to-Row
Spacing
*Metric equivalents for post length are .150 = [3.81]; .180 = [4.57].
1For .040 [1.02] diameter hole.
Note: Other connector sizes can be made available, consult Tyco Electronics.
Flow Solder Post Solder Eyelet Contact
No. of Dimensions Post With Without With Without
Dual Length* Mounting Mounting Mounting Mounting
Positions ABCDE Ears Ears Ears Ears
1.100 1.535 .370 1.240 1.785
627.94 38.99 9.40 31.50 45.34 .150 — — 2-530654-1 —
1.724 2.159 .370 1.864 2.409
10 43.79 54.84 9.40 47.35 61.19 .150 2-530657-2 — 2-530654-2 —
2.504 2.939 .370 2.644 3.189 .150 2-530657-4 — 2-530654-4 2-530667-4
15 63.60 74.65 9.40 67.16 81.00 .180 — 2-530669-4 — —
2.972 3.407 .370 3.112 3.657
18 75.49 86.54 9.40 79.04 92.89 .150 — 2-530668-5 2-530654-5 —
3.596 4.031 .370 3.736 4.281
22 91.34 102.39 9.40 94.89 108.74 .150 2-530657-6 2-530668-6 2-530654-6 —
3.908 4.343 .370 4.048 4.593
24 99.26 110.31 9.40 102.81 116.66 .150 — — 2-530654-7 —
4.532 4.967 .370 4.672 5.217
28 115.11 126.16 9.40 118.67 132.51 .150 3-530657-2 3-530668-2 3-530654-2 —
4.844 5.279 .437 4.984 5.529
30 123.04 134.09 11.10 126.59 140.44 — — — 2-530654-9 —
5.780 6.215 .437 5.920 6.465 .150 — — 3-530654-0 —
36 146.81 155.58 11.10 150.36 164.21 .180 — 3-530669-0 — —
6.872 7.307 .437 7.012 7.557
43 174.55 185.60 11.10 178.10 191.95 .150 3-530657-3 — 3-530654-3 —
63
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Low Profile Connectors (Continued)
Material: Glass-filled nylon
Part No. 650025-2
Keying Plug
Recommended PC Board
Edge Patterns .125 [3.18] Centerline Boards
Intercontact Key
.156 [3.96] Centerline Boards
.300
[7.52] Min.
.300
[7.52] Min.
.175
[4.45] Min.
Recommended
Gold Area
.175
[4.45] Min.
Recommended
Gold Area
Intercontact
KeySlot
Intercontact
KeySlot
.125
[3.18]
.156
[3.96]
.160
[4.06]
.400
[10.16]
.050
[1.27]
.050
[1.27]
.125
[3.18]
.400
[10.16]
.078±.005
.000
[1.98±0.13]
0.00
.094±.005
.000
[2.39±0.13]
0.00
64
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
64
Twin Leaf Mother Board Connectors
Product Facts
■Wide variety of sizes avail-
able from 3 dual positions
and up—no initial tooling
investment required for new
versions
■Connectors can be selec-
tively loaded with contacts
in custom patterns
■Connectors tooled on all
standard centerlines—
.100 [2.54], .125 [3.18],
.150 [3.81], .156 [3.96],
and .200 [5.08]
Note: .200 [5.08] centerline capabili-
ties provided by loading every-other
dual position of .100 [2.54] centerline
housings.
■Closed card entry protects
contacts and daughter
board pads
■Adapts to a wide range of
mother board thicknesses
to .104 [2.64] maximum
■Phosphor bronze contacts
selectively plated for top
performance and maximum
economy
■Protective channel helps
prevent overstress of
contacts
■Daughter board keying
available in intercontact or
on-contact styles
■Recognized under the
Component Program
of Underwriters
Laboratories Inc.,
File No. E28476
The AMP Twin Leaf
Connector is a highly
reliable, low-cost mother/
daughter board connector
designed for solid-state
circuitry. The one-piece,
multi-contact connector
requires no front-end tooling.
This versatile connector for
double-sided printed circuit
boards uses preloaded
contacts and selective plat-
ing to give lowest applied
cost. Critical contact areas
are gold-over-nickel plated
to provide positive electrical
connection between con-
tacts and daughter board
pads. Contact posts are tin
plated for efficient dip
soldering to mother boards
up to .104 [2.64] thick.
The Twin Leaf Connector
delivers high reliability
because the contacts
possess superior tolerance
of environmental stresses
including shock, vibration
and variations of tempera-
ture and humidity. Other
characteristics such as high
insulation resistance, low
Performance Specifications
Contact Rating*:
3 amperes continuous
Temperature Rating:
–55°C to +105°C
Insulation Resistance:
5,000 megohms
Dielectric Withstanding Voltage:
Test Voltage (AC, RMS)
Altitude Contact Spacing
.100 [2.54] .150 [3.81]
Sea Level 1,000 1,500
50,000 ft
15 240 m 400 600
70,000 ft
21 336 m 280 400
Termination Resistance:
10 milliohms, max.
Durability: Tested to 100 cycles
(engage/withdraw)
Contact Plating: .000015 [0.00038]
selective gold plating on contact area;
bright tin on solder tine
*Consult Tyco Electronics engi-
neering when paralleling con-
tacts for power applications.
termination resistance, long
life and moderate contact
separation force meet
industry requirements for
reliability. Connectors are
tooled in sizes from 3
through 80 dual-contact
positions with contacts on
.100 [2.54], .125 [3.18],
.150 [3.81], .156 [3.96]
or .200 [5.08] centers.
Other sizes and custom-
loaded contact patterns
are available on request.
The connector housing,
made of glass-filled poly-
ester with a UL 94V-0
rating, features a standoff
which facilitates the use of a
probe for electrical continuity
checks without risk of dam-
age to the contacts. A
closed card-entry design of
the housing protects the
contacts and daughter
board pads. Housings
accept daughter boards
ranging from .055 [1.40] to
.070 [1.78] in thickness.
Intercontact and on-contact
keys are available for
polarization of the housings.
Card guides or end caps
make alignment of daughter
board pads with Twin Leaf
Connector contacts quick
and easy.
65
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors Without End Caps
*Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines, except where noted;
.170 [4.32] for .100 [2.54] and .125 [3.18] centerlines, except where noted.
A
A
.010 x .024
[0.25 x 0.61]
Post for .035 [0.89]
Dia. Hole
Fit for
.055-.070
[1.4-1.78]
PCBoard
.135* .170*
[3.43] or [4.32]
.400
[10.16]
.225
[5.72]
.610
[15.49]
.200
[5.08]
Card Slot
Depth
.400 [10.16]
Max.
.100 [2.54], .125 [3.18],
.150 [3.81] and
.156 [3.96] Centerlines,
With Solder Posts
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000015 [0.00038] gold in contact area;
tin on posts, with entire contact under-
plated .000030 [0.00076] nickel, except
where noted
Related Product Data:
Performance Specifications—
page 64
Card Guides—pages 70, 71
Keying Plugs—page 72
PC Board Hole Layouts—page 71
Technical Documents:
(pages 186, 187):
Product Specification
108-9027
Instruction Sheets 408-7479,
408-7498, 408-7506
B
D
66
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
66
Twin Leaf Mother Board Connectors Without End Caps
A = .100 [2.54] A = .125 [3.18] A = .150 [3.81] A = .156 [3.96]
No. of Centerline Spacing Centerline Spacing Centerline Spacing Centerline Spacing
Dual B D Part B D Part B D Part B D Part
Positions Numbers Numbers Numbers Numbers
.300 .600
2 — — — — — — 7.62 15.24 1,31-583694-1 — — —
.200 .400 .300 .600 .312 .624
35.08 10.16 583485-6 — — — 7.62 15.24 1,31-645155-11,3 7.92 15.85 4-583486-8
.450 .750
4 — — — — — — 11.43 19.05 583407-5 — — —
.400 .600 .600 .900
510.16 15.24 583485-7 — — — 15.24 22.86 583407-6 — — —
1.050 1.350
8 — — — — — — 26.67 34.29 583407-9 — — —
1.000 1.250
9 — — — 25.40 31.75 583533-7 — — — — — —
.900 1.100 1.400 1.720
10 22.86 27.94 1-583485-2 — — — — — — 35.56 43.69 4-583486-1
1.500 1.800
11 — — — — — — 38.10 45.72 1-583407-2 — — —
1.300 1.500
14 33.02 38.10 1-583485-6 — — — — — — — — —
2.100 2.400
15 — — — — — — 53.34 60.96 1-583407-5 — — —
2.125 2.375 2.652 2.964
18 — — — 53.97 60.32 1-583533-6 — — — 67.36 75.28 3-583486-3
2.850 3.150 2-583407-0
20 — — — — — — 72.39 80.01 530292-93— — —
2.625 2.875
22 — — — 66.67 73.02 2-583533-0 — — — — — —
4.050 4.350 4.212 4.524
28 — — — — — — 102.87 110.49 583407-1 106.99 114.91 2-583486-3
3.625 3.875 4.524 4.836
30 — — — 92.08 98.43 531534-22— — — 114.91 122.83 2-583486-1
4.500 4.800
31 — — — — — — 53.34 60.96 530292-33— — —
4.992 5.304
33 — — — — — — — — — 126.80 134.72 1-583486-8
5.460 5.772
36 — — — — — — — — — 138.68 146.61 1-583486-5
4.875 5.125 5.850 6.150 6.084 6.396
40 — — — 123.83 130.18 3-583533-8 148.59 156.21 3-583407-8 154.53 162.46 1-583486-1
6.552 6.864
43 — — — — — — — — — 166.42 174.35 583486-8
4.900 5.100 6.130 6.380 7.350 7.650 7.640 7.960
50 124.46 129.54 583485-3 155.70 162.05 5-583533-01186.69 194.31 4-583407-8 194.06 202.18 583486-1
8.580 8.892
56 — — — — — — — — — 217.93 225.86 5-583486-0
6.400 6.600
65 162.56 167.64 5-583485-6 — — — — — — — — —
7.900 8.100
80 200.66 205.74 5-583485-5 — — — — — — — — —
1Contacts are plated .000030 [0.00076] gold in contact area, tin on posts, with entire contact underplated .000030 [0.00076] nickel.
2Post length .135 [3.43]
3Post length .170 [4.32]
Note: Other connector sizes can be made available, consult Tyco Electronics.
67
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors With End Caps
**Post length: .135 [3.43] for .150 [3.81] and .156 [3.96] centerlines;
.170 [4.32] for .100 [2.54] and .125 [3.18] centerlines.
**See page 27 for dimensions.
F
A
G
.010 x .024
[0.25 x 0.61]
Post for .035 [0.89]
Dia. Hole
Fit for
.055-.070
[1.4-1.78]
PCBoard
.135* .170*
[3.43] or [4.32]
.400
[10.16]
.225
[5.72]
.610
[15.49]
.200
[5.08]
.062
[1.58]
Card Slot
Depth
.400 [10.16]
Max.
Accepts #2
Self-tapping
Screw
.100 [2.54], .125 [3.18],
.150 [3.81] and
.156 [3.96] Centerlines,
With Solder Posts
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000015 [0.00038] gold in contact area;
tin on posts, with entire contact under-
plated .000030 [0.00076] nickel
Related Product Data:
Performance Specifications—
page 64
Keying Plugs—page 72
PC Board Hole Layouts—page 71
Technical Documents:
(pages 186, 187):
Product Specification
108-9027
Instruction Sheets 408-7479,
408-7498, 408-7506
B E**
68
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
68
Twin Leaf Mother Board Connectors With End Caps
Note: Other connector sizes can be made available, consult Tyco Electronics.
No. of A = .100 [2.54] Centerline Spacing A = .125 [3.18] Centerline Spacing A = .150 [3.81] Centerline Spacing A = .156 [3.96] Centerline Spacing
Dual Part Part Part Part
Pos. B F G Numbers B F G Numbers B F G Numbers B F G Numbers
.200 .400 .734
35.03 10.16 18.64 1-583715-1 — — — — — — — — — — — —
.400 .600 .934
510.16 15.24 23.72 1-583715-3 — — — — — — — — — — — —
.500 .700 1.034 .625 .875 1.259 .780 1.092 1.538
612.70 17.78 26.26 1-583715-4 15.88 22.23 31.96 1-583679-5 — — — — 19.81 27.74 39.07 1-583660-6
.600 .800 1.134
715.24 20.32 28.80 1-583715-5 — — — — — — — — — — — —
.800 1.000 1.334
920.32 25.40 33.88 1-583715-7 — — — — — — — — — — — —
.900 1.100 1.434 1.404 1.716 2.162
10 22.86 27.94 36.42 1-583715-8 — — — — — — — — 35.66 43.59 54.91 1-583660-0
1.100 1.300 1.634 1.716 2.028 2.474
12 27.94 33.02 41.50 1-583715-0 — — — — — — — — 43.58 51.51 62.84 1-583660-2
1.200 1.400 1.734
13 30.48 35.56 44.04 1-583715-1 — — — — — — — — — — — —
1.950 2.250 2.684 2.028 2.340 2.786
14 — — — — — — — — 49.53 57.15 68.17 1-583692-3 51.51 59.44 70.76 1-583660-4
1.400 1.600 1.934 2.100 2.400 2.834 2.184 2.496 2.942
15 35.56 40.64 49.12 1-583715-3 — — — — 53.34 60.96 71.98 1-583692-4 55.47 63.40 74.73 1-583660-2
1.600 1.800 2.134 2.000 2.250 2.634
17 40.64 45.72 54.20 1-583715-5 50.80 57.15 66.90 1-583679-6 — — — — — — — —
1.700 1.900 2.234 2.125 2.375 2.759 2.652 2.964 3.410
18 43.18 48.26 56.74 1-583715-6 53.98 60.33 70.08 1-583679-7 — — — — 67.36 75.28 86.61 1-583660-7
1.900 2.100 2.434 2.375 2.625 3.009
20 48.26 53.34 61.82 1-583715-8 60.33 66.68 76.43 1-583679-9 — — — — — — — —
3.276 3.588 4.034
22 — — — — — — — — — — — — 83.21 91.14 102.46 2-583660-1
2.400 2.600 2.934 3.000 3.250 3.634 3.600 3.900 4.334 3.744 4.065 4.502
25 60.96 66.04 74.52 2-583715-3 76.20 82.55 92.30 2-583679-4 91.44 99.06 110.08 2-583692-4 95.10 103.02 114.35 2-583660-4
2.500 2.700 3.034
26 63.50 68.58 77.05 2-583715-4 — — — — — — — — — — — —
2.700 2.900 3.234 3.375 3.625 4.009 4.212 4.524 4.979
28 68.58 73.66 82.14 2-583715-6 85.73 92.08 101.83 2-583679-6 — — — — 106.98 114.91 126.24 2-583660-7
2.900 3.100 3.434 4.350 4.650 5.084 4.524 4.836 5.282
30 73.66 78.74 87.22 2-583715-8 — — — — 110.49 118.11 129.13 1-583692-1 114.91 122.83 134.16 2-583660-9
3.000 3.200 3.534
31 76.20 81.28 89.76 2-583715-9 — — — — — — — — — — — —
3.100 3.300 3.634 4.836 5.148 5.594
32 78.74 83.82 92.30 3-583715-0 — — — — — — — — 122.83 130.76 142.09 3-583660-1
4.800 5.100 5.534
33 — — — — — — — — 121.92 129.54 140.56 3-583692-1 — — — —
3.300 3.500 3.834
34 83.82 88.90 97.38 3-583715-2 — — — — — — — — — — — —
3.400 3.600 3.934 5.100 5.400 5.834 5.304 5.616 6.062
35 83.36 91.44 99.92 3-583715-3 — — — — 129.54 137.16 148.18 3-583692-3 134.72 142.64 153.97 3-583660-4
3.500 3.700 4.034 5.250 5.550 5.984 5.460 5.772 6.218
36 88.90 93.98 102.46 3-583715-4 — — — — 133.35 140.97 151.99 3-583692-4 138.68 146.61 157.94 1-583660-1
3.900 4.100 4.434 4.875 5.125 5.509 5.850 6.150 6.584
40 99.06 104.14 112.62 3-583715-8 123.83 130.18 139.93 3-583679-8 148.59 156.21 167.23 3-583692-8 — — — —
4.000 4.200 4.534
41 101.60 106.68 115.16 3-583715-9 — — — — — — — — — — — —
6.552 6.864 7.310
43 — — — — — — — — — — — — 166.42 174.35 185.67 4-583660-1
4.900 5.100 5.434 6.125 6.375 6.759 7.350 7.650 8.084 7.644 7.956 8.402
50 124.46 129.54 138.02 4-583715-8 155.58 161.93 171.68 4-583679-8 186.69 194.31 205.33 4-583692-8 194.16 202.08 213.41 4-583660-8
7.900 8.100 8.434
80 200.66 205.74 214.22 5-583715-7 — — — — — — — — — — — —
69
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors With End Caps (Continued)
Typical Connector and Card Guide Assembly
Double Slotted
Card Guide (Without Stand-off)
End Cap
Daughter Board
Self-tapping #2
Screw (2 Reqd.)
Self-tapping #2
Screw (2 Reqd.)
Stand-off
*Must be .063 [1.59] thick for use with Double Slotted Card Guides.
Self-tapping #2
Screw (1 Reqd.)
Mother Board
.104 [2.64] Max.
Thickness*
Double Slotted
Card Guide (With Stand-off)
Single Slotted
Card Guide
70
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
70
Twin Leaf Mother Board Connectors (Continued)
Card Guides
Material: Glass-filled nylon, black
Part No. 583671-1
Related Product Data:
Connectors used with—page 65
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7498,
408-7506
Single Slotted
Single Slotted Card Guide
and Connector Mounting
Dimensions
A E
.100 .263
2.54 6.68
.125 .288
3.18 7.31
.150 .313
3.81 7.95
.156 .319
3.96 8.10
.210
[5.33]
.100
[2.54]
.200
[5.08]
Connector
Centerline
Contact
Centerline
.035
[0.89] Dia.
Mounting Hole
.091
[2.31]
Dia.
A
E
Min.
.225
[5.72]
3.770
[95.76]
3.585
[91.06]
.170
[4.32]
.523
[13.28] .225
[5.72]
.137
[3.48]
.074
[1.88] Dia.
Thru Hole
.074 [1.88] Dia. x
.175 [4.45] Deep
71
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Twin Leaf Mother Board Connectors (Continued)
Card Guides
(Continued)
Material: Nylon, natural
Part No. 583425-1
Related Product Data:
Connectors used with—page 65
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-7498,
408-7506
Double Slotted Without Stand-off
.080
[2.03]
1.680
[42.67] 1.500
[38.10]
.300
[7.62]
.540
[13.72]
.150
[3.81]
.400
[10.16]
Double Slotted Card Guide
and Connector Mounting
.100
[2.54]
.200
[5.08]
Connector
Centerline
Contact
Centerline
.035
[0.89] Dia.
Mounting Hole
.310
[7.87]
A
E
Min.
.175
[4.45]
Recommended PC Board
Layout for Connectors
With End Caps
.100
[2.54]
.200
[5.08]
Connector
Centerline
Contact
Centerline
.035
[0.89] Dia.
Mounting Hole
.100
[2.54]
Dia.
AE
Dimensions
A E
.100 .328
2.54 8.33
.125 .353
3.18 8.96
.150 .376
3.81 9.60
.156 .384
3.96 9.75
Dimensions
A E
.100 .267
2.54 6.78
.125 .317
3.18 8.05
.150 .367
3.81 9.32
.156 .379
3.96 9.62
Note: Mother Board
must be .063 [1.59] thick
for use with Double
Slotted Card Guides.
72
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
72
Twin Leaf Mother Board Connectors (Continued)
Keying Plugs
Other Twin Leaf
Mother Board
Connectors
Material: Nylon, natural
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-7479 Type A Type B
Intercontact On-Contact
In-Row Type Connector Style* Intercontact Keying Plug On-Contact Keying Plug
Contact of with without Type A Type B Insertion/Extraction Part Insertion/Extraction
Spacing Contact End Caps End Caps Part Numbers Part Numbers Tool Numbers Tool
.100 Solder Post 583715 583485
2.54 Card Extender 530268 530291 530286-3 — 91081-2 583714-1 91088-1
.125 Solder Post 583679 583533
3.18 Card Extender 530265 530290 530286-2 530030-1 91081-1 583714-1 91088-1
.150 Solder Post 583692 583407
Wrap-Type Post 583754 583752 530286-2 530030-1 91081-1 — —
3.81 Card Extender 530278 530270
.156 Solder Post 583660 583486
Wrap-Type Post 583755 583753 530286-2 530030-1 91081-1 — —
3.96 Card Extender 530267 530282
*Refer to pages 66-68, as applicable, for specific connector sizes.
A
.475
[12.06]
Min.
Fits for
.055-.070
[1.4-1.78]
PCBoard
.610
[15.49]
.225
[5.72]
.400
[10.16]
Connector Dimension A
Centerlines Intercontact On-Contact
.100 .040 .129
2.54 1.02 3.28
.125 .050 .129
3.18 1.27 3.28
.150 .050 .160
3.81 1.27 4.06
.156 .050 .160
3.96 1.27 4.06
For more information on the connec-
tors shown here, consult Tyco
Electronics.
Recommended PC Board Cutout for Keying Plugs
Card Extender Connectors
Connectors With End Caps
Part Number
Centerlines Series*
.150
3.81 530278
.156
3.96 530267
*Consult Tyco Electronicsfor
specific connector sizes.
73
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors
AMP Rotary Cam Zero
Insertion Force (ZIF) Card
Edge Connectors are avail-
able in sizes to fit most
industry-standard printed
circuit boards. A clockwise
rotation of the cam handle
opens contacts to allow
zero-force insertion or
removal of PC boards—
even boards with a large
number of contacts. Turning
the cam handle to close the
connector locks the board
securely in place. Rotary
Cam ZIF Connectors
accept double-sided PC
boards .054-.070 [1.37-
1.78] thick, with contact
centerline intervals of .100
[2.54], .125 [3.18] and .156
[3.96]. Row-to-row spacing
of connector posts is .200
[5.08] for .100 [2.54] and
.156 [3.96] connectors and
.250 [6.35] for .125 [3.18]
connectors.
Contacts are nickel under-
plated phosphor bronze
with gold plate in the
contact area and tin-lead
plated posts. Contact con-
figurations include vertical
and right-angle solder posts
and wrap-type posts.
Preassembled connectors
feature housings made from
94V-0 rated glass-filled
polyester and mounting
ears for easy mounting to
the mother board. Housings
are available with one end
open, both ends open and
both ends closed for side
and top daughter board
insertion. Integral board
locks secure boards in the
connectors. Accessories
include dust covers, cam
rods (with and without
boots) and cam keys for
nut-driver actuation and
for tandem operation of
connectors.
Performance Specifications
Current vs. Temperature Rise*:
3 amperes at 30°C
Operating Temperature:
–55°C to +105°C
Contact Resistance:
20 milliohms max.
Durability: Tested to 5000 cycles
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Product Facts
■Zero insertion force; little or
no effort required to insert
and withdraw PC boards
■Reduced pad wear for
extended board life
■Allows all four sides of
board to be used for
input/output functions
■Accepts double-sided
boards
■Three contact styles to
choose from: vertical solder
post, right-angle solder post
and wrap-type post (2 and 3
high)
■Available in .100 [2.54],
.125 [3.18] and .156 [3.96]
centerlines
■Three configurations avail-
able: open one end, open
both ends and closed both
ends
■Products indicated are
recognized under the
Component Program of
Underwriters
Laboratories Inc.,
File No. E28476
74
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
74
Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline
Vertical Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18] .370
[9.40]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.100
[2.54]
Typ.
.250
[6.35]
.050
[1.27]
.018
[0.46]
Typ.
.200
[5.08]
Closed
Position
.150
[3.81]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open Closed
Positions A B C D E* One End1Both Ends1Both Ends
2.100 2.800 3.100 2.300 .125 1-531020-1 — 1-531019-1
22 53.34 71.12 78.74 58.42 .160 1-531020-1 — —
2.400 3.100 3.400 2.600 .125 1-531020-2 — 1-531019-2
25 60.96 78.74 86.36 66.04 .160 1-531020-2 — —
2.700 3.400 3.700 2.900
28 68.58 86.36 93.98 73.66 .160 21-531020-3 — —
3.000 3.700 4.000 3.200
31 76.20 93.98 101.60 81.28 .160 2-531020-1 — —
3.500 4.200 4.500 3.700 .125 3-531020-2 — 1-531019-4
36 88.90 106.68 114.30 93.98 .160 1-531020-4 — —
3.900 4.600 4.900 4.100 .125 1-531020-5 — —
40 99.06 116.84 124.46 104.14 .160 1-531020-5 — —
4.200 4.900 5.200 4.400 .125 3-531020-3 — —
43 1-531020-7 — —
106.68 124.46 132.08 111.76 .160 22-531020-82— —
4.900 5.600 5.900 5.100 .125 1-531020-8 531021-8 —
50 1-531020-8 — 1-531019-8
124.46 142.24 149.86 129.54 .160 22-531020-92— —
5.900 6.600 6.900 6.100
60 149.86 167.64 175.26 154.94 .160 1-531020-9 1-531021-9 1-531019-9
6.400 7.100 7.400 6.600 .125 1-531020-0 — —
65 2-531020-0 — —
162.56 180.34 187.96 167.64 .160 23-531020-02— —
*Metric equivalents in millimeters for post lengths Eare .125 = [3.18]; .160 = [4.06].
1Recognized under the Component Program of Underwriters Laboratories Inc.
2Connectors without cam rod and boardlock.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
75
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued)
Right-Angle Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—page 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18]
Closed End
B
A
D
C
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.025
[0.64]
Typ.
.100
[2.54]
Typ.
.100
[2.54]
.250
[6.35]
.050
[1.27]
.160
[4.06]
.200
[5.08]
Closed
Position
.150
[3.81]
.370
[9.40]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Bend Part Numbers
Dual (Open End1)
Positions A B C D Right
2.400 3.100 3.400 2.800
25 60.96 78.74 86.36 71.12 R1-531395-23
3.500 4.200 4.500 3.700
36 88.90 106.68 114.30 93.98 R1-531396-4
4.900 5.600 5.900 5.100
50 124.56 142.24 149.86 129.54 L 1-531396-8
6.400 7.100 7.400 6.600
65 162.56 180.34 187.96 167.64 R 1-531396-0
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown.
2. Other connector sizes can be made available, consult Tyco Electronics.
3. Open both ends.
Bend Right Shown
76
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
76
Rotary Cam ZIF Connectors, .100 x .200 [2.54 x 5.08] Centerline (Continued)
Vertical Connector,
Wrap-Type Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18] .370
[9.40]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.100
[2.54]
Typ.
.250
[6.35]
.050
[1.27]
.200
[5.08]
Closed
Position
.150
[3.81]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open
Positions A B C D E* One End1Both Ends1
2.400 3.100 3.400 2.600
25 60.96 78.74 86.36 66.04 .380 1-531414-2 —
3.500 4.200 4.500 3.700 .580 1-531414-4 1-531415-4
36 88.90 106.68 114.30 93.98 .380 1-531414-4 —
3.900 4.600 4.900 4.100
40 99.06 116.84 124.46 104.14 .580 1-531414-5 —
4.100 4.800 5.100 4.300
42 104.14 121.92 129.54 109.22 .380 1-531414-6 —
4.900 5.600 5.900 5.100
50 124.46 142.24 149.86 129.54 .580 2-531414-4 1-531415-8
5.900 6.600 6.900 6.100
60 149.86 167.64 175.26 154.94 .580 1-531414-9 —
6.400 7.100 7.400 6.600
65 162.56 180.34 187.96 167.64 .580 1-531414-0 —
*Metric equivalents in millimeters for post lengths Eare . 5 8 0 = [14.73] (3-high wrap-type); . 3 8 0 = [9.65] (2-high wrap-type).
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
.025
[0.64]
Typ.
77
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors, .125 x .250 [3.18 x 6.35] Centerline
Vertical Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186,187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ. .018
[0.46]
Typ.
.125
[3.18]
Typ.
.250
[6.35]
.050
[1.27]
.250
[6.35]
Closed
Position
.150
[3.81]
.370
[9.40]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open
Positions A B C D E* One End1Both Ends1
3.375 4.125 4.425 3.625
28 85.73 104.76 112.40 92.08 .125 —1-531024-3
3.625 4.375 4.675 3.875
30 92.08 111.13 118.75 98.43 .125 1-531023-4 —
4.875 5.625 5.925 5.125
40 123.83 142.88 150.50 130.18 .160 1-531023-4 1-531024-4
*Metric equivalents in millimeters for post lengths Eare . 1 2 5 = [3.18]; . 1 6 0 = [4.06].
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
78
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Rotary Cam ZIF Connectors, .156 x .200 [3.96 x 5.08] Centerline
Vertical Connector,
Solder Post Terminals
Material and Finish:
Housing—Glass-filled polyester,
94V-0 rated
Contacts—Phosphor bronze, plated
.000030 [0.00076] gold per MIL-G-
45204 in contact area; .000100
[0.00254] tin-lead per MIL-P-81728
on post with entire contact underplated
.000050 [0.00127] nickel per QQ-N-290
Related Product Data:
Board Lock Feature—On connectors
open one end and open both ends
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 73
Dust Cover—page 79
PC Board Hole Layout and Edge
Patterns—pages 81, 82
Special Application—pages 82, 96
Technical Documents:
(pages 186, 187):
Product Specification
108-9048
Instruction Sheet 408-7911
.440
[11.18] .370
[9.40]
Closed End
B
A
D
C
E
.130 [3.3] Dia. Holes
.250 [6.35] Dia. C’Bore
.080 [2.03] Deep
.025
[0.64]
Typ.
.156
[3.96]
Typ.
.250
[6.35]
.050
[1.27]
.200
[5.08]
Closed
Position
.150
[3.81]
.850
[21.60]
1.095
[27.81]
Ref.
.210
[5.33]
No. of Dimensions Part Numbers
Dual Open Open Closed
Positions A B C D E* One End1Both Ends1Both Ends
3.276 4.088 4.388 3.588 .125 531025-3 — —
22 83.21 103.83 111.46 91.14 .160 531025-9 — 531007-9
5.460 6.272 6.572 5.772
36 138.68 159.31 166.93 146.61 .160 — 1-531026-1 —
6.552 7.364 7.664 6.864
43 166.42 187.05 194.67 174.35 .125 531025-6 — —
*Metric equivalents in millimeters for post lengths Eare . 1 2 5 = [3.18]; . 1 6 0 = [4.06].
1Recognized under the Component Program of Underwriters Laboratories Inc.
Notes: 1. Connector with card slot open one end is shown for illustration purposes.
2. Other connector sizes can be made available, consult Tyco Electronics.
.018
[0.46]
Typ.
79
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Accessories
Dimension Part
A Numbers
3.185
80.90 650083-1
3.705
94.11 650083-2
4.470
113.54 650083-3
5.285
134.24 650083-4
5.900
149.86 650083-6
5.975
151.77 532563-7
Dimension Part
A Numbers
11.050
280.67 531863-2
48.000
1219.20 531863-1
Dimension Part
A Numbers
6.385
162.18 650083-7
6.985
177.42 650083-8
7.485
190.12 650083-9
7.725
196.22 1-532563-0
8.320
211.34 1-650083-7
Note: Other lengths can be made avail-
able upon request, consult Tyco
Electronics.
Note: Other lengths can be made available
upon request, consult Tyco Electronics.
Material:
Cam Rod—Stainless steel
Boot—Glass-filled polyester, yellow
Material: Rigid vinyl, black
Dust Covers
Cam Rods with Boot
A
A
.348
[8.84]
.200
[5.08]
.200
[5.08] .400
[10.16]
.835
[21.21]
.654
[16.61]
80
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Accessories (Continued)
Dimension Part
A Numbers
2.200
55.88 2-531004-8
2.700
68.58 2-531004-9
3.300
83.82 3-531004-0
4.750
120.65 2-531004-4
5.000
127.00 1-531004-4
5.500
139.70 2-531004-6
Dimension Part
A Numbers
3.380
85.85 645293-3
4.50
114.30 645293-8
5.200
132.08 645293-6
6.90
175.30 645293-7
13.120
333.25 645293-5
Dimension Part
A Numbers
6.000
152.40 2-531004-7
6.250
158.75 1-531004-6
6.750
171.45 1-531004-7
8.250
209.55 3-531004-2
12.500
317.50 2-531004-0
Note: Other lengths can be made avail-
able upon request, consult Tyco
Electronics.
Note: Other lengths can be made avail-
able upon request, consult Tyco
Electronics.
Material: Stainless steel
Cam Rods without Boot
A
A
.125
[3.18]
.260
[6.60] .045
[1.14]
.252
[6.40]
.055
[1.40]
.125
[3.18]
.055
[1.40]
.200
[5.08] .045
[1.14]
.775
[19.69]
81
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Recommended PC Board Hole Layouts
A*
A*
Pin No. 1 (Ref.)
PCBoard Edge
W
X
B*
CL
.200
[5.08]
Mother Board Hole Layout, Vertical Through-Board Connectors
*Refer to individual connector specifications.
Mother Board Hole Layout, Right-Angle Through-Board Connectors
CL W X
.100 .200 .350
2.54 5.08 8.89
.125 .250 .375
2.18 6.35 9.53
.156 .200 .406
3.96 5.08 10.31
.048
[1.22] Dia. Typ.
.128
[3.25] Dia.
(2 Plc.)
.048
[1.22] Dia. Typ. .400
[10.16] Max.
.100
[2.54]Typ.
*Refer to individual connector specifications.
82
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Recommended PC Board Edge Pattern
A
CL
CL Minus .006 [0.15]
Daughter Board Edge Pattern
Tandem Application
.270
[6.86]
Min.
.700
[17.78]
Min.
B±.005
[±0.13]
C+.005
-.000
[+0.13]
Note: Contact Tyco Electronics for information concerning special tandem connectors.
Special Application
No. of CL = .100 [2.54] CL = .125 [3.18] CL = .156 [3.96]
Dual C = .050 [1.27] C = .078 [1.98] C = .094 [2.39]
Positions A B A B A B
2.100 2.288 3.267 3.576
22 53.34 58.12 — — 83.21 90.83
2.400 2.588
25 60.96 65.74 — — — —
2.700 2.888 3.375 3.613
28 68.58 73.36 85.73 91.77 — —
3.625 3.863
30 — — 92.08 98.12 — —
3.000 3.188
31 76.20 80.98 — — — —
3.500 3.688 5.460 5.760
36 88.90 93.68 — — 138.68 146.30
3.900 4.088 4.875 5.113
40 99.06 103.84 123.83 129.87 — —
4.200 4.388 6.552 6.852
43 106.68 111.46 — — 166.42 174.04
4.900 5.088
50 124.46 129.24 — — — —
5.900 6.088
60 149.86 154.64 — — — —
6.400 6.588
65 162.56 167.34 — — — —
Special Rod
(Part No. Series 645293)
Allows Customer Supplied
Nut Driver Actuation
(Refer to page 80.)
83
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors
AMP Linear Zero Insertion
Force (ZIF) PC Board Edge
Connectors are available in
both lever and bell crank
actuated styles and can be
provided as panel assem-
blies, separate housings
and contacts or as pre-
assembled with solder post
terminals.
Panel assemblies include a
housing with ACTION PIN
press-fit solderless contacts
mounted on an epoxy
board for rack application.
Separate housing assem-
blies and ACTION PIN con-
tacts allow customer
assembly. These can be
mounted as close as .625
[15.88]. More design lati-
tude for high density appli-
cation is provided by the
side entry lever-type con-
nector, permitting use of all
sides of the PC board for
edge-type I/O connections
(see page 133). Where
solder applications are
required, Tyco Electronics
has a line of preassembled
connectors with tin-plated
solder terminals. All these
configurations are available
in a broad range of sizes.
With ZIF style connectors,
intermittencies can occur if
a contact comes to rest on
a piece of foreign matter
(dust and dirt particles)
found on PC boards. To
decrease the probability of
this happening, all connec-
tors have been designed to
include a wiping contact
which produces a wiping
action. This action, pro-
duced by the geometry and
bending movements of the
beam, pushes aside debris
and allows for good electri-
cal connection by cleaning
the actual point of contact.
In addition, all connectors
have removable wings
which make it possible to
repair or replace damaged
cam rails, handles, contacts
and housing modules with-
out removing the entire
housing assembly from the
board.
Performance Specifications
Current vs. Temperature Rise*:
3 amperes at 30°C
Operating Temperature:
–65°C to +85°C
Contact Resistance:
16 milliohms max.
Durability: Tested to 250 cycles
(board-to-contact actuation)
*Consult Tyco Electronicsengi-
neering when paralleling con-
tacts for power applications.
Product Facts
■Minimizes force needed to
install and remove printed
circuit boards
■Available in lever and bell
crank styles
■Lever styles allow side and
top card entry
■Wiping action contacts
enhance electrical
properties
■Contacts on .100 x .100
[2.54 x 2.54] or .125 x .125
[3.18 x 3.18] centers
■.025 [0.64] square posts
■Accepts PC boards from
.054 to .070 [1.37 to 1.78]
in thickness
■Normally closed design
leaves springs in relaxed
position
■50 to 175 dual positions
available on .100 [2.54]
centerline connectors and
40 to 140 dual positions
available on .125 [3.18]
centerline connectors
84
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline
Housing with Solder Posts
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] min. gold per
MIL-G-45204 in contact area; .000100
[0.00254] min. tin-lead on post with
entire contact underplated .000050
[0.00127] min. nickel per QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 88
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specification
108-14015
Application Specification
114-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
Lever Style, Side Entry
No. of Dimensions Part
Dual
Positions ABC Number
6.113 3.400 2.000
35 155.27 86.36 50.80 1-645135-2
11.613 7.900 3.000
80 294.97 200.66 76.20 1-645135-1
13.613 9.900 3.000
100 345.77 251.46 76.20 1-645135-5
Note: Other connector sizes can be made available, consult Tyco Electronics.
Section P-P
*Card slot depth.
.450
[11.43]
.355
[9.02]*
.845
[21.46]
.600
[15.24]
.100
[2.54] .190
[4.83]
.103
[2.62]
.845
[21.46]
.175
[4.45]
P
P
Closed End
Open End
Mounting
Hole C
Mounting
Hole C
1.075
[27.31]
.206
[5.23]
.100
[2.54] Typ.
.500
[12.70]
Max.
A
C
B
Closed
L
Open
C Last Contact Position C First Contact Position
LL
L
85
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Panel Assembly Lever Style, Side Entry
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 88
ACTION PIN Contacts—
pages 88, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specification
108-14015
Application Specification
114-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
.343
[8.71]
Max.
Closed End
C
.125
[3.18]
1.555
[39.50]
D
.150 [3.81]
Countersunk
Hole (2 Plcs.)
1.425
[36.16]
A
.100
[2.54]
Typ.
.100
[2.54]
.812
[20.62]
.750
[19.05]
B
Open End
.355
[9.02]
Card Slot
Depth
PC Board
Channel
No. of Dimensions Part
Dual
Positions ABCDNumbers
7.400 10.125 3.000 .615
75 251.46 320.68 76.20 15.62 1-645145-0
9.900 12.625 3.000 .615
100 251.46 320.68 76.20 15.62 1-645145-5
12.900 15.625 3.000 .615
130 251.46 320.68 76.20 15.62 2-645145-1
13.900 16.625 3.000 .615
140 353.06 422.28 76.20 15.62 2-645145-3
14.900 17.625 3.000 .615
150 251.46 320.68 76.20 15.62 2-645145-5
15.900 18.625 3.000 .615
160 403.86 473.07 76.20 15.62 2-645145-7
15.900 18.625 3.000 .455
160 403.86 473.07 76.20 11.56 147400-1
Note: Other connector sizes can be made available, consult Tyco Electronics.
86
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Panel Assembly Lever Style, Top Entry
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 88
ACTION PIN Contacts—
pages 88, 94
Tooling—page 95
Technical Documents:
(pages 186, 187):
Product Specifications
108-14015, 108-26003
Application Specification
114-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
.343
[8.71]
Max.
Closed End
C
.125
[3.18]
1.555
[39.50]
.615
[15.62]
.150 [3.81]
Countersunk
Hole (2 Plcs.)
1.425
[36.16]
A
.100
[2.54]
Typ.
.100
[2.54]
.812
[20.62]
.750
[19.05]
B
Closed End
.355
[9.02]
Card Slot
Depth
PC Board
Channel
No. of Dimensions Part
Dual
Positions ABCNumbers
10.900 13.625 3.000
110 276.86 346.08 76.20 1-645147-7
11.900 14.625 3.000
120 302.26 371.48 76.20 1-645147-9
Note: Other connector sizes can be made available, consult Tyco Electronics.
87
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
Housing
Material: Glass-filled polyester, black
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Mounting Screws—Customer sup-
plies, must be applied before opening
connector
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 88
ACTION PIN Contacts—
pages 88, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Product Specifications
108-14015, 108-26003
Application Specification
108-26003
Instruction Sheets 408-2995,
408-2999, 408-6915
Lever Style, Side Entry
No. of Dimensions Part
Dual
Positions ABC Numbers
7.613 4.900 2.000
50 193.37 124.46 50.80 1-645115-5
11.113 7.400 3.000
75 282.27 187.96 76.20 1-645115-0
11.613 7.900 3.000
80 294.97 200.66 76.20 1-645115-1
13.613 9.900 3.000
100 345.77 251.46 76.20 1-645115-5
14.613 10.900 3.000 1-645115-7
110 371.17 276.86 76.20 3-645115-2
15.113 11.400 3.000
115 383.87 289.56 76.20 1-645115-8
16.113 12.400 3.000
125 409.27 314.96 76.20 2-645115-0
16.613 12.900 3.000
130 421.97 327.66 76.20 2-645115-1
17.613 13.900 3.000
140 447.37 353.06 76.20 2-645115-3
19.613 15.900 3.000
160 498.17 403.86 76.20 3-645115-3
21.113 17.400 3.000
175 536.27 441.96 76.20 3-645115-0
Note: Other connector sizes can be made available, consult Tyco Electronics.
Section P-P
*Card slot depth.
.450
[11.43]
.815
[20.70] .600
[15.24]
.355
[9.02]*
P
P
Closed EndOpen End
Mounting
Hole C .206
[5.23]
A
Ref.
C
B
Closed
L
Open
C Last Contact Position C First Contact Position
LL
88
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .100 x .100 [2.54 x 2.54] Centerline (Continued)
ACTION PIN Contacts with Wiping Feature,
.100 [2.54] Centerline Recommended PC Board Hole Layout and Edge Pattern,
.100 [2.54] Centerline
Material and Finish:
Copper alloy 725, plated .000015
[0.00038] gold per MIL-G-45204 in
contact area; .000001 [0.00003] min.
gold flash per MIL-G-45204 on post
with entire contact underplated .000050
[0.00127] nickel per QQ-N-290
Related Product Data:
Performance Specifications—
page 83
ACTION PIN Contact Description
and Application Specification—
page 94
Tooling—page 95
Mother Board Hole Layout
Daughter Board Edge Pattern
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-2665
Contact Combs
Reeled Contacts
Number of Dimension Part
Contacts
Per Comb* A Number
5.400
55 137.16 4-119311-1
*At least two (2) contact combs required per housing.
Note: Other sizes can be made available, consult Tyco Electronics.
Note: Other plating combinations and thicknesses can be made available,
consult Tyco Electronics.
Number of Part
Contacts
Per Reel Number
35,000 119196-6
.745
[18.92]
A
(Comb)
B
Min.
A
Max.
B
C
L
C
L
C
.045
[1.14]
Contact Area
1.485
[37.72]
.740
[18.80]
Post Area
.100
[2.54]
.100
[2.54] .070
[1.78]
.100 (No. of Pos. –1) +.196
[2.54 (No. of Pos. –1) +4.98]
.600
[15.24] Ref. .200
[5.08] Min.
.098
[2.49] Typ.
.120
[3.05] Dia.
.047
[1.19] Dia. Typ.
(Solder Post Only)*
.025
[0.64] Sq.
Prenotched
for Breakoff
at Assembly
Prenotched
for Breakoff
at Assembly
*For ACTION PIN post hole diameter, see page 94.
Connector Dimensions
Style A B C
.100 .100 .206 .175
Lever 2.54 2.54 5.23 4.45
Connector Entry Dimensions
Style Style A B
.240
Side 6.10 —
Lever .240 .320
Top 6.10 8.13
89
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline
Panel Assembly
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts—
pages 93, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Lever Style, Side Entry
.343
[8.71] Max.
PC Board
Channel .355
[9.02]
Card Slot
Depth
Open End Closed End
.125
[3.18]
1.555
[39.50]
.150 [3.81]
Countersunk
Hole (2 Plcs.)
1.425
[36.16]
A
.125
[3.18]
.812
[20.62]
.750
[19.05]
B
.125
[3.18] Typ.
.615
[15.62]
C
No. of Dimensions Part
Dual
Positions A B C Numbers
4.875 7.625 2.000
40 123.83 193.68 50.80 1-645146-5
6.875 9.625 3.000
56 174.63 244.48 76.20 1-645146-9
7.375 10.125 3.000
60 187.32 257.17 76.20 1-645146-0
8.875 11.625 3.000
72 225.43 295.28 76.20 1-645146-3
10.375 13.125 3.000
84 250.83 320.68 76.20 1-645146-6
15.375 18.125 3.000
124 390.53 460.38 76.20 2-645146-6
Note: Other connector sizes can be made available, consult Tyco Electronics.
90
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
Panel Assembly
Material and Finish:
Housing—Glass-filled polyester,
black
Contacts—Copper alloy 725, plated
.000015 [0.00038] gold per MIL-G-
45204 in contact area; .000001
[0.00003] min. gold flash per MIL-G-
45204 on post with entire contact under-
plated .000050 [0.00127] nickel per
QQ-N-290
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts—
pages 93, 94
Tooling—page 95
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Bell Crank Style, Top Entry
.355
[9.02]
Card Slot
Depth
3.620
[91.95] Ref.
(Open)
.125
[3.18]
Closed End
1.555
[39.50]
.615
[15.62]
2.41
[54.38] A.609
[15.47]
.125
[3.18]
B
.750
[19.05]
.935
[23.75] Max.
.125
[3.18] Typ.
No. of Dimensions Part
Dual
Positions A B Numbers
7.375 10.625
60 187.33 269.88 1-645149-0
9.875 13.125
80 250.82 333.38 1-645149-5
13.875 17.125
112 352.43 434.98 2-645149-3
17.375 20.625
140 441.33 523.88 3-645149-0
Note: Other connector sizes can be made available, consult Tyco Electronics.
91
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
Housing
Material: Glass-filled polyester, black
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Mounting Screws—Customer
supplied, must be applied before
opening connector
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts—
pages 93, 94
Tooling—page 95
Special Application—page 96
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Lever Style, Side Entry
Closed
Closed End
Open End
Open
First Contact Position
*Card slot depth.
Section P-P
.475
[12.07]
.355
[9.02]*
.815
[20.7] .600
[15.24]
1.087
[27.61]
.218
[5.54]
A
Ref.
.115
[2.92]
CP
P
B
C
Mounting Hole
C
L
Mounting Hole
C
L
LLast Contact Position
C
L
No. of Dimensions Part
Dual
Positions A B C Number
14.112 10.375 3.000
84 358.44 263.52 76.20 1-645116-6
16.112 12.375 3.000
100 409.24 314.33 76.20 2-645116-0
17.612 15.775 3.000
112 447.34 400.68 76.20 2-645116-3
19.112 17.275 3.000
124 485.44 438.78 76.20 2-645116-6
Note: Other connector sizes can be made available, consult Tyco Electronics.
92
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
Housing
Material: Glass-filled polyester, black
Related Product Data:
Daughter PC Board—.054-.070
[1.37-1.78] thick
Mounting Screws—Customer
supplied, must be applied before
opening connector
Performance Specifications—
page 83
PC Board Hole Layout and Edge
Pattern—page 93
ACTION PIN Contacts—
pages 93, 94
Tooling—page 95
Technical Documents:
(pages 186, 187):
Instruction Sheets 408-2995,
408-6915, 408-6916
Bell Crank Style, Top Entry
Closed End
First Contact Position
*Card slot depth.
Section P-P
.475
[12.07]
.355
[9.02]*
.815
[20.7]
.600
[15.24]
1.250
[31.75]
1.820
[46.23]
.115
[2.92]
1.062
[26.97]
(Open)
2.562
[65.07]
(Closed)
A
Ref.
.312
[7.92]
.500
[12.70]
.187
[4.75]
.115
[2.92]
1.874
[47.60]
P
P
B
C
Mounting Hole
C
L
Mounting Hole
C
L
LLast Contact Position
C
L
No. of Dimensions Part
Dual
Positions A B Numbers
8.562 6.375
52 217.47 161.93 1-645142-8
9.562 7.375
60 242.87 187.32 1-645142-0
13.125 9.875
80 333.37 250.82 1-645142-5
16.062 13.875
112 407.97 352.43 2-645142-3
Note: Other connector sizes can be made available, consult Tyco Electronics.
93
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors, .125 x .125 [3.18 x 3.18] Centerline (Continued)
ACTION PIN Contacts with Wiping Feature,
.125 [3.18] Centerline Recommended PC Board Hole Layout and Edge Pattern,
.125 [3.18] Centerline
Material and Finish:
Copper alloy 725, plated .000015
[0.00038] gold per MIL-G-45204 in
contact area; .000001 [0.00003] min.
gold flash per MIL-G-45204 on post
with entire contact underplated .000050
[0.00127] nickel per QQ-N-290
Related Product Data:
Performance Specifications—
page 83
ACTION PIN Contact Description
and Application Specification—
page 94
Tooling—page 95
Mother Board Hole Layout
Daughter Board Edge Pattern
Technical Documents:
(pages 186, 187):
Instruction Sheet 408-2665
Contact Combs
Number of Dimension Part
Contacts
Per Comb* A Number
6.875
56 174.63 1-119950-2
*At least two (2) contact combs required per housing.
Note: Other sizes can be made available, consult Tyco Electronics.
.750
[19.05]
A
(Comb)
B
Min.
A
Max.
B
C
LC
.045
[1.14]
Contact Area
1.490
[37.85]
.740
[18.80]
Post Area
.125
[3.18]
.125
[3.18]
.125 (No. of Pos. –1) +.220
[3.18 (No. of Pos. –1) +5.59]
.600
[15.24] Ref.
.200
[5.08] Min.
.090
[1.78] Typ.
.110
[2.79] Typ.
.120
[3.05] Dia.
.047
[1.19] Dia. Typ.
(Solder Post Only)*
.025
[0.64] Sq.
Prenotched
for Breakoff
at Assembly
*For ACTION PIN post hole diameter, see page 94.
Connector Dimensions
Style C A B C
.125 .125 .218 .187
Lever 3.18 3.18 5.54 4.75
.125 .125 1.250 .187
Bell-Crank 3.18 3.18 31.75 4.75
Connector Entry Dimensions
Style Style A B
.240
Side 6.10 —
Lever .240 .320
Top 6.10 8.13
.775 .600
Bell-Crank Top 19.68 15.24
L
94
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors (Continued)
AMP ACTION PIN
Press-Fit Contacts
ACTION PIN contacts provide a reliable press-fit connection.
Localized pressure in the interface area entails oxide
break-through and helps prevent corrosion in the harshest
environments to provide a reliable connection virtually every
time. Also, radial and axial distortion are controlled to meet
today’s standards for multilayer board applications.
PC Board Thickness
ACTION PIN contacts are
designed for use in a variety of
PC board thicknesses. However,
certain ACTION PIN contacts
are to be used in specific ranges
of board thicknesses. To
promote optimum performance,
the recommended board thick-
nesses provided with the con-
nector being used must be
followed.
➀Annular Ring (See Note)
➁Drilled Hole
➂Copper Thickness
➃Tin-Lead Thickness
➄Plated Through-Hole
ACTION PIN Contact/PC Board Applications
*Maximum hardness of copper layer is 150 Knoop.
Note: Recommended annular ring diameter is hole diameter plus .020 [0.51].
Connector ACTION PIN Drilled Hole Plating Thicknesses Plated Radial Hole Distortion
Contact Through-Hole
Type Material Thickness Diameter➁Copper➂* Tin-Lead➃Diameter➄Average Maximum
.0003
Linear ZIF .025 .0453±.001 .001-.003 0.008 .037-.043 Not Not
0.64 1.151±0.03 0.03-0.08 Min. 0.94-1.09 Specified Specified
95
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors (Continued)
Tooling Assembly tooling is not
required except when
using connectors with
ACTION PIN contacts.
ACTION PIN contact
assembly requires an
arbor-style bench tool with a
capacity of 40 lb [178 N] per
contact, a support fixture,
contact applicator, carrier
removal tool and housing
assembly tool.
Typical procedure is to
place a PC board on the
support fixture, insert contact
combs into the printed circuit
board with the contact appli-
cator and seat with the arbor
tool. Next, remove the carrier
strip from the contact combs
with the carrier break-off tool.
Place the housing over the
contacts with the housing
assembly tool, and repeat
the entire process until the
board is complete.
.100 x .100 [2.54 x 2.54] Centerline Connectors
No. of T-Bar Carrier Housing Housing Wing Removal/ Housing Contact Replacement Tools
Dual Removal Assembly Removal Replacement Insertion
Positions Applicator Tool Tool Tool Tool Tool With Housing Without Housing
50 266267-4 265924-4 313136-1
80 266267-3 265924-4 313136-2
100 266267-4 265924-4
110 266267-5 265924-4 313136-3
115 266267-5 265924-4 313256-1 266233-1 266264-1 266235-1 3-265871-2
120 266267-5 265924-4
125 266267-4 265924-4 313136-4
140 266267-4 265924-4
175 266267-5 265924-4 313136-5
.125 x .125 [3.18 x 3.18] Centerline Connectors
No. of T-Bar Carrier Housing Housing Wing Removal/ Housing Contact Replacement Tools
Dual Removal Assembly Removal Replacement Insertion
Positions Applicator Tool Tool Tool Tool Tool With Housing Without Housing
40 313139-1 265924-4 313136-1
52 313139-2 265924-6
56 313139-2 265924-6 313136-2
60 313139-2 265924-7
72 313139-3 265924-4 313256-1 266233-1 266264-1 266235-1 3-265871-2
84 313139-2 265924-5 313136-3
112 313139-2 265924-7 313136-4
124 313139-2 265924-5
140 313139-2 265924-5 313136-5
96
Catalog 1654080 Dimensions are in inches and Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Issued 7-03 millimeters unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com are metric equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
Card Edge Connectors
(Solder Type, Board-to-Board)
Linear ZIF Connectors (Continued)
Special Application
Use Linear and Rotary ZIF Connectors as Card Guides
to access more sides of the Daughter Board.
Standard Edge II
(pages 15 thru 27)
or AMP PACE Connectors
(pages 98 thru 115)
