ACA2402 750/870/1000 MHz CATV Push-Pull Line Amplifier Data Sheet - Rev 2.2 FEATURES * 1 GHz Specified Performance * 22 dB Gain * Very Low Distortion * Excellent 75 Input and Output Match * Stable with High VSWR Load Conditions * Monolithic Design for Consistent Performance Part-to-Part * Low DC Power Consumption * Surface Mount Package Compatible with Automatic Assembly * Low Cost Alternative to Hybrids * Meets Cenelec Standards * Materials set consistent with RoHS Directives. S7 Package 16 Pin Wide Body SOIC with Heat Slug APPLICATIONS * CATV Line Amplifiers, System Amplifiers, Distribution Nodes PRODUCT DESCRIPTION The ACA2402 is a highly linear, monolithic GaAs RF amplifier that has been developed as an alternative to standard CATV hybrid amplifiers. Offered in a convenient surface mount package, the MMIC consists of two pairs of parallel amplifiers that are optimized for exceptionally low distortion and noise figure. A RF Input hybrid equivalent that provides flat gain response and excellent input and output return loss over the 40 to 1000 MHz CATV downstream band is formed when one ACA2402 is cascaded between two appropriate transmission line baluns. 1A 2A 1B 2B ACA2402 Figure 1: Hybrid Application Diagram 12/2008 RF Output ACA2402 1 GND GND 16 2 2A IN 1A OUT 15 3 GND Bias 1A 14 4 1A IN 2A OUT 13 5 1B IN 2B OUT 12 6 I SET Bias 1B 11 7 2B IN 1B OUT 10 8 GND GND 9 Figure 2: Pin Out Table 1: Pin Description 2 PIN NAME DESCRIPTION PIN NAME DESCRIPTION 1 GND Ground 16 GND Ground 2 2AIN Amplifier 2A Input 15 1AOUT Amplifier 1A Output 3 GND Ground 14 Bias 1A Bias for 1A Amplifier 4 1AIN Amplifier 1A Input 13 2AOUT Amplifier 2A Output and Supply 5 1BIN Amplifier 1B Input 12 2BOUT Amplifier 2B Output and Supply 6 1SET Current Adjust 11 Bias 1B Bias for 1B Amplifier 7 2BIN Amplifier 2B Input 10 1BOUT Amplifier 1B Output 8 GND Ground 9 GND Ground Data Sheet - Rev 2.2 12/2008 ACA2402 ELECTRICAL CHARACTERISTICS Table 2: Absolute Mimimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply (pins 12, 13) 0 +28 VDC RF Power at Inputs (pins 4, 5) - +75 dBmV -65 +150 C Soldering Temperature - +260 C Soldering Time - 5.0 Sec Storage Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: 1. Pins 2, 4, 5 and 7 should be AC-coupled. No external DC bias should be applied. 2. Pin 6 should be AC-grounded and/or pulled to ground through a resistor for current control. No external DC bias should be applied. 3. Pins 11 and 14 are bias feeds for input amplifiers 1A and 1B. No external DC bias should be applied. 4. Pins 10 and 15 receive DC bias directly from pins 11 and 14. No other external bias should be applied. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT - +24 - VDC RF Frequency 40 - 1000 MHz Case Temperature -40 - +110 C Supply: VDD (pins 12, 13) The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet - Rev 2.2 12/2008 3 ACA2402 Table 4: AC and DC Electrical Specifications (Ta = +25 C, Vdd = +24 VDC) PARAMETER MIN TYP MAX UNIT Gain @ 1000 MHz (1) 21.1 21.6 22.1 dB Cable Equivalent Slope (1) - 0 - dB Gain Flatness (1) @ 1000 MHz - 0.2 - dB Noise Figure - 3.5 4.5 dB CTB (1) 77 Channels (2) 77 Channels plus QAM to 1 GHz (6) 110 Channels (3) 110 Channels plus QAM to 1 GHz (7) 128 Channels (4) - -76 -73 -70 -74 -74 -71 -71 - CSO (1) 77 Channels (2) 77 Channels plus QAM to 1 GHz (6) 110 Channels (3) 110 Channels plus QAM to 1 GHz (7) 128 Channels (4) - -72 -72 -69 -70 -70 -70 -68 - XMOD (1) 77 Channels (2) 77 Channels plus QAM to 1 GHz (6) 110 Channels (3) 110 Channels plus QAM to 1 GHz (7) 128 Channels (4) - -65 -65 -62 -63 -63 -63 -63 - 18 22 - dB 240 250 260 mA - - 3.8 (1) Return Loss (Input/Output) (1) Supply Current (5) Thermal Resistance dBc dBc dBc C/W O Notes: (1) Measured with baluns on the input and output of the device. (2) Parts measured with 77 channels flat output, +42 dBmV per channel. (3) Parts measured with 110 channels flat output, +40 dBmV per channel. (4) Parts measured with 128 channels flat output, +40 dBmV per channel. (5) The supply current may be reduced by decreasing the value of R3 (see Figure 17) (6) 47.5 dBmV output, 9.5 dB tilt @ 1 GHz (7) 45.5 dBmV output, 9.5 dB tilt @ 1 GHz 8. All specifications as measured on Evaluation Board (see Figures 16 & 17). 4 Data Sheet - Rev 2.2 12/2008 COMMENTS 75 system ACA2402 PERFORMANCE DATA Figure 3: Noise Figure vs Frequency 5 Noise Figure (dB) 4.5 4 3.5 3 2.5 2 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Figure 4: Gain (S21) vs. Frequency Data Sheet - Rev 2.2 12/2008 5 ACA2402 Figure 5: Input and Output Return Loss (S11 and S22) vs. Frequency 5 0 S11 S22 -5 S22 (dB) -10 -15 -20 -25 -30 -35 -40 0 100 200 300 400 500 600 700 800 900 Frequency (MHz) Figure 6: Isolation (S12) vs. Frequency 6 Data Sheet - Rev 2.2 12/2008 1000 1100 1200 ACA2402 Figure 7: CTB vs. Output Power at Worst-case Channel/Frequency (128 total channels, 110 analog channels, flat output) Figure 8: CSO vs. Output Power at Worst-case Channel/Frequency (128 total channels, 110 analog channels, flat output) Figure 9: XMOD vs. Output Power at Worst-case Channel/Frequency (128 total channels, 110 analog channels, flat output) Data Sheet - Rev 2.2 12/2008 7 ACA2402 Figure 10: CTB vs. Frequency (110 channels, +40 dBmV power, flat output) -50 -55 -60 CTB (dBc) -65 -70 -75 -80 -85 -90 -95 -100 0 100 200 300 400 500 600 700 800 Frequency (MHz) Figure 11: CSO vs. Frequency (110 channels, +40 dBmV power, flat output) -50 -55 -60 CSO (dBc) -65 -70 -75 -80 -85 -90 -95 -100 0 100 200 300 400 500 600 700 800 Frequency (MHz) Figure 12: XMOD vs. Frequency (110 channels, +40 dBmV power, flat output) -50 -55 -60 XMOD (dBc) -65 -70 -75 -80 -85 -90 -95 -100 0 100 200 300 400 500 Frequency (MHz) 8 Data Sheet - Rev 2.2 12/2008 600 700 800 ACA2402 Figure 13: CTB vs. Frequency (77 channels, +42 dBmV power, flat output) -50 -55 -60 CTB (dBc) -65 -70 -75 -80 -85 -90 -95 -100 0 100 200 300 400 500 Frequency (MHz) 600 Figure 14: CSO vs. Frequency (77 channels, +42 dBmV power, flat output) -50 -55 CSO (dBc) -60 -65 -70 -75 -80 -85 -90 -95 -100 0 100 200 300 400 500 600 Frequency (MHz) Figure 15: XMOD vs. Frequency (77 channels, +42 dBmV power, flat output) -50 -55 XMOD (dBc) -60 -65 -70 -75 -80 -85 -90 -95 -100 0 100 200 300 400 500 600 Frequency (MHz) Data Sheet - Rev 2.2 12/2008 9 ACA2402 APPLICATION INFORMATION Figure 16: Evaluation Board Layout Notes: 1. Via holes should be 35 mils (0.89 mm) in diameter, and plated to 1 mil (0.025 mm) thickness. They need not be solderfilled. 2. WARNING: Due to the power dissipation of this device, the printed circuit board should be mounted/attached to a heat sink. 3. More assembly details, such as via hole diameters, via spacing, solder paste application, and soldering recommendations are provided in the application note entitled, "Thermal Management of ANADIGICS' Surface Mounted Amplifiers". Figure 17: Evaluation Board Schematic 10 Data Sheet - Rev 2.2 12/2008 ACA2402 Table 5: Evaluation Board Parts List REF DESCRIPTION C1, C2, C3, C6, C7, C10, C14 0.01 F CHIP CAP C4, C5, C8, C9 QTY VENDOR VENDOR P/N 7 MURATA GRM39X7R103K50V 470 pF CHIP CAP 4 MURATA GRM39X7R471K50V C12, C13 1.0 pF CHIP CAP 2 MURATA GRM36COG1R0C50 C15 47 F ELECT. CAP 1 DIGI-KEY CORP P5275-ND R1, R2, C11 NOT USED R3 18 k RESISTOR 1 DIGI-KEY CORP P18KGCT-ND TVS TVS 24 VOLT 600 WATT 1 DIGI-KEY CORP SMBJ24ACCCT-ND L1, L2, L3, L4 (3) 680 nH INDUCTOR 4 COILCRAFT 1008CS-681XKBC CONNECTOR (1) 75 N MALE PANEL MOUNT 2 PASTERNACK ENTERPRISES PE4504 Ferrite Core 2 FAIR-RITE 2843002702 MWS WIRE IND. T-2361429-20 T1, T2 (2) (BALUN) INDIUM Wire Printed Circuit Board 1 STANDARD PRINTED CIRC. INC 24VX1AC50 300 X 160 MILS 1 INDIUM CORP OF AMERICA 14996Y Notes: (1) N connector center pin should be approximately 80 mils in length. (2) T1, T2 balun: 5.5 turns thru, as shown in Figure 18. (3) 200 mA minimum current rating. Figure 18: Balun Drawing Data Sheet - Rev 2.2 12/2008 11 ACA2402 PACKAGE OUTLINE Figure 19: S7 Package Outline - 16 Pin Wide Body SOIC with Heat Slug 12 Data Sheet - Rev 2.2 12/2008 ACA2402 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING ACA2402S7TR -40 to 110 oC 16 Pin Wide Body SOIC with Heat Slug 1,500 piece tape and reel ACA2402RS7P2 -40 to 110 oC RoHS-Compliant 16 Pin Wide Body SOIC with Heat Slug 1,500 piece tape and reel ACA2402S7P0 -40 to 110 oC 16 Pin Wide Body SOIC with Heat Slug Plastic tubes (50 pieces per tube) ACA2402RS7P0 -40 to 110 oC RoHS-Compliant 16 Pin Wide Body SOIC with Heat Slug Plastic tubes (50 pieces per tube) ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 13 Data Sheet - Rev 2.2 12/2008