VS2 Series Convergent Mode Sensors Miniature self-contained sensors VS2 Series Convergent Mode Sensor Features * Extremely low profile self-contained miniature sensors * 10 to 30V dc operation * Visible red sensing beam * Choose models with 15 mm or 30 mm convergent point * Choose dark or light operate models * Choose models with NPN (sinking) or PNP (sourcing) output * 3-wire hookup; output load capacity to 50 mA * Choice of integral cable or quick-disconnect connector VS2 Series Overview VS2 Series miniature self-contained sensors are designed for precision sensing in small areas previously accessible only to remote or fiber optic models. Typical applications include mounting inside vibrating feeders and electronic component handling equipment, where larger sensors will not fit. Visible red, 660 nm VS2 Series Convergent-Mode Sensors Models* Range VS2AN5CV15 VS2AN5CV15Q VS2RN5CV15 VS2RN5CV15Q VS2AP5CV15 VS2AP5CV15Q Cable 15 mm (0.6") 5 mm 2 m (6.5') 3-Pin Pico QD VS2AN5CV30 VS2AN5CV30Q 2 m (6.5') 3-Pin Pico QD VS2RP5CV30 VS2RP5CV30Q 10 to 30V dc NPN Light Operate NPN Dark Operate PNP Light Operate PNP Dark Operate NPN Light Operate NPN Dark Operate PNP Light Operate PNP Dark Operate 2 m (6.5') 3-Pin Pico QD 2 m (6.5') 3-Pin Pico QD VS2AP5CV30 VS2AP5CV30Q Output Type 2 m (6.5') 3-Pin Pico QD VS2RP5CV15 VS2RP5CV15Q VS2RN5CV30 VS2RN5CV30Q Supply Voltage 30 mm (1.2") 10 mm 2 m (6.5') 3-Pin Pico QD 2 m (6.5') 3-Pin Pico QD 2 m (6.5') 3-Pin Pico QD Excess Gain Beam Pattern 1000 E X C E S S G A I N 100 VS2CV15 6 mm Convergent Mode 4 mm VS2CV15 0.24 in 0.16 in Convergent Mode 2 mm 0.08 in 0 10 0 2 mm 0.08 in 4 mm 0.16 in 6 mm 1 1 mm 0.04 in 0.24 in 0 10 mm 0.4 in 100 mm 4 in 1000 mm 40 in 20 mm .8 in 40 mm 1.6 in 60 mm 2.4 in 80 mm 100 mm 3.2 in 4.0 in DISTANCE DISTANCE 1000 E X C E S S G A I N VS2CV30 0.36 in 6 mm Convergent Mode 100 VS2CV30 9 mm 0.24 in Convergent Mode 3 mm 0 10 1 1 mm 0.04 in 0 3 mm 0.12 in 6 mm 0.24 in 9 mm 0.36 in 0 10 mm 0.4 in 100 mm 4 in 1000 mm 40 in 0.12 in 40 mm 1.6 in 80 mm 120 mm 160 mm 200 mm 3.2 in 4.8 in 6.4 in 8.0 in DISTANCE DISTANCE See Safety Use Warning on Back Page. Printed in USA 10/00 P/N 65411L0A VS2 Series Convergent Mode VS2 Series Specifications Supply Voltage and Current 10 to 30V dc (10% maximum ripple) at less than 25 mA (exclusive of load) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration SPST solid-state switch Choose NPN (current sinking) or PNP (current sourcing) models Choose light operate (N.O.) or dark operate (N.C.) models Output Rating 50 mA maximum Off-state leakage current: < 1 microamp at 24V dc On-state saturation voltage: < 0.25V at 10 mA dc; < 0.5V at 50 mA dc Output Protection Circuitry Protected against false pulse on power-up and continuous overload or short circuit of outputs Overload trip point 100 mA Output Response Time 1 millisecond ON and OFF (NOTE: 150 millisecond delay maximum on power-up: output does not conduct during this time) Repeatability 160 microseconds Indicators Two LEDs: Green and Yellow GREEN ON steadily GREEN flashing YELLOW ON steadily = power to sensor is ON = output overload = light is sensed Construction Black ABS housing with acrylic lens Environmental Rating IEC IP67; NEMA 6 Connections 2 m (6.5') attached cable: three #28 ga stranded conductors with PE insulation; PVC outer cable jacket; or 3-pin Pico-style pigtail quick-disconnect fitting. QD cables are ordered separately. Operating Conditions Temperature: -20 to +55C (-4 to +131F) Maximum Relative Humidity: 80% at 50C (non-condensing) Vibration and Mechanical Shock Vibration: All models meet IEC 60068-2-6, IEC 60947-5-2, UL491 Section 40, MIL-STD-202F Method 201A; 10 to 60 Hz, 0.5 mm peak to peak Shock: All models meet IEC 60068-2-27, IEC 60947-5-2; 30g peak acceleration, 11 millisecond pulse duration, half-sine wave pulse shape Application Notes M2 stainless steel mounting hardware included. Optional mounting brackets are available (page 4). Certifications VS2 Series Sensor Hookups Sensors with NPN Outputs Cabled hookup bu - 10-30V dc + bn bk Quick-Disconnect hookup - 10-30V dc + bn bk page 2 Load bn + 10-30V dc - bu bk Load bu Sensors with PNP Outputs Cabled hookup Load Quick-Disconnect hookup bn + 10-30V dc - bu bk Load Banner Engineering Corp. * Minneapolis, U.S.A. www.bannerengineering.com * Tel: 763.544.3164 VS2 Series Convergent Mode VS2 Series Convergent Mode Sensor Dimensions 12.0 mm (0.47") CL Green Power Indicator 8.0 mm (0.31") 4.7 mm (0.19") 3.6 mm (0.14") 2.0 mm (0.08") 150 mm (6") Pigtail VS2CV30 VS2CV15 21.2 mm 20.6 mm (0.84") (0.81") 25.1 mm (0.99") Yellow Signal Indicator (Receiver only) 10.9 mm (0.43") 2x o2.2 mm (0.09") 4.8 mm (0.19") Accessories Quick-Disconnect (QD) Cables Style 3-pin Pico Style Straight Models Length PKG3M-2 2 m (6.5') PKG3M-9 9 m (30') For Use With Dimensions 34.7 mm (1.37") All VS2 Series sensors with model suffix "Q". Pinout M8 x 1 9.6 mm (0.38") Black Wire Blue Wire Brown Wire VS2 Series Mounting Brackets SMBVS2RA * Right-angle bracket * 300 series stainless steel 8.0 mm (0.32") 2x 3.2 mm (0.13") 3.0 mm (0.12") 7.0 mm (0.28") 5.5 mm (0.22") 8.0 mm (0.32") 3.0 mm (0.12") 8.0 mm (0.32") 0.9 mm (0.04") 20.0 mm (0.79") 9.0 mm (0.35") 20.0 mm (0.79") Banner Engineering Corp. * Minneapolis, U.S.A. www.bannerengineering.com * Tel: 763.544.3164 14.0 mm (0.55") 4 x o2.3 mm (0.09") page 3 VS2 Series Convergent Mode ! WARNING . . . Not To Be Used for Personnel Protection Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death. These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection. WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any other warranty either expressed or implied. Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 * Phone: 763.544.3164 * Fax: 763.544.3213 * E-mail: sensors@baneng.com