LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Designed for ease in circuit board assembly. * Black case enhance contrast ratio. * Solid state light source. * Reliable and rugged. Package Dimensions Part No. Source Lens LTL-4232NH63P Color Green Transparent Green NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25mm(.010") unless otherwise noted. 3. The holder color is black. 4. The holder raw material is nylon. 5. The LED lamp is LTL-4232N. Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 1 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at Ta=25 Parameter Maximum Rating Unit 100 mW 120 mA Continuous Forward Current 30 mA Derating Linear From 50 0.4 mA/ Operating Temperature Range -55 to + 100 Storage Temperature Range -55 to + 100 Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) Lead Soldering Temperature [1.6mm(.063") From Body] Part No. : LTL-4232NH63P BNS-OD-C131/A4 260 for 5 Seconds Page : 2 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical Optical Characteristics at Ta=25 Parameter Symbol Part No. LTL- Min. Typ. Max. Unit Test Condition 4232NH63P 12.6 40 mcd IF = 10mA Note 1,4 21/2 4232NH63P 45 deg Note 2 (Fig.6) Peak Emission Wavelength p 4232NH63P 565 nm Measurement @Peak (Fig.1) Dominant Wavelength d 4232NH63P 569 nm Note 3 Spectral Line Half-Width 4232NH63P 30 nm Forward Voltage VF 4232NH63P 2.1 Reverse Current IR 4232NH63P Luminous Intensity Viewing Angle IV 2.6 V IF = 20mA 100 A VR = 5V, Note 5 Note: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, d is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Iv needs 15% additionary for guaranteed limits. 5. Reverse Voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 3 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25 Ambient Temperature Unless Otherwise Noted) Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 4 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Packing Spec 500, 200 or 100 pcs per packing bag 10 packing bags per inner carton total 5,000 pcs per inner carton 8 Inner cartons per outer carton total 40,000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 5 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon's Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 30C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3 mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 5. Soldering When soldering, leave a minimum of 2mm clearance from the base of the lens/Holder to the soldering point. Dipping the lens/Holder into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions : Soldering iron Temperature Soldering time 350C Max. 3 sec. Max. (one time only) Wave soldering Pre-heat Pre-heat time Solder wave Soldering time 100C Max. 60 sec. Max. 260C Max. 5 sec. Max. Note: Excessive soldering temperature and/or time might result in deformation of the LED/Holder or catastrophic failure of the CBI. IR(Hot air) re-flow is not suitable process for through hole type LED lamp production. Max. temperature of wave soldering is not mean that Holder's HDT/Melting temperature. Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 6 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A LED Circuit model B LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs 7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Use a conductive wrist band or anti- electrostatic glove when handling these LEDs All devices, equipment, and machinery must be properly grounded Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 7 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Suggested checking list : Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DSL? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 8 of 9 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 8. Reliability Test Classification Test Item Reference Standard Ta= Under Room Temperature As Per Data Sheet Maximum Rating Test Time= 1000HRS MIL-STD-750D:1026 (1995) MIL-STD-883D:1005 (1991) JIS C 7021:B-1 (1982) High Temperature High Humidity Storage Ta= 655C RH= 90 95% MIL-STD-202F: 103B(1980) JIS C 7021 : B-11(1982) High Temperature Storage Ta= 1055C Test Time= 1000HRS MIL-STD-883D:1008 (1991) JIS C 7021:B-10 (1982) Low Temperature Storage Ta= -555C Test Time=1000HRS JIS C 7021:B-12 (1982) Temperature Cycling 105C 25C -55C 25C 30mins 5mins 30mins 5mins 10 Cycles MIL-STD-202F:107D (1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1010 (1991) JIS C 7021: A-4(1982) Thermal Shock 105 5C -55C 5C 10mins 10mins 10 Cycles MIL-STD-202F:107D(1980) MIL-STD-750D:1051(1995) MIL-STD-883D:1011 (1991) Solder Resistance T.sol = 260 C Max. Dwell Time= 5secs Max. MIL-STD-202F:210A(1980) MIL-STD-750D:2031(1995) JIS C 7021: A-1(1982) T. sol = 230 5C Dwell Time= 5 1secs MIL-STD-202F:208D(1980) MIL-STD-750D:2026(1995) MIL-STD-883D:2003(1991) JIS C 7021: A-2(1982) Operation Life Endurance Test Test Condition Environmental Test Solderability Test Time= 240HRS 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL-4232NH63P BNS-OD-C131/A4 Page : 9 of 9