LTC4300A-3 Level Shifting Hot Swappable 2-Wire Bus Buffer with Enable U FEATURES DESCRIPTIO The LTC(R)4300A-3 hot swappable 2-wire bus buffer allows I/O card insertion into a live backplane without corruption of the data and clock busses. When the connection is made, the LTC4300A-3 provides bidirectional buffering, keeping the backplane and card capacitances isolated. Rise-time accelerator circuitry allows the use of weaker DC pull-up currents while still meeting rise-time requirements. During insertion, the SDA and SCL lines are precharged to 1V to minimize bus disturbances. Bidirectional Buffer* for SDA and SCL Lines Increases Fanout Prevents SDA and SCL Corruption During Live Board Insertion and Removal from Backplane Logic Threshold ENABLE Input Isolates Input SDA and SCL Lines from Output Compatible with I2CTM, I2C Fast Mode and SMBus Standards (Up to 400kHz Operation) 1V Precharge on all SDA and SCL Lines Supports Clock Stretching, Arbitration and Synchronization 5V to 3.3V Level Translation High Impedance SDA, SCL Pins for VCC = 0V, VCC2 = 0V Small 8-Pin DFN and MSOP Packages The LTC4300A-3 provides level translation between 3.3V and 5V supplies. The backplane and card can both be powered with supplies ranging from 2.7V to 5.5V. The LTC4300A-3 also incorporates a CMOS threshold ENABLE pin which forces the part into a low current mode and isolates the card from the backplane. When driven to VCC, the ENABLE pin sets normal operation. U APPLICATIO S The LTC4300A-3 is available in the MSOP and 3mm x 3mm DFN packages. Hot Board Insertion Servers Capacitance Buffer/Bus Extender Desktop Computer , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. *Patent pending. U TYPICAL APPLICATIO VCC 3.3V Input-Output Connection VCC2 0.01F 0.01F 10k SCLIN 10k 8 10k 1 3 2 6 7 10k SCLOUT INPUT SIDE 150pF OUTPUT SIDE 50pF 0.5V/DIV SDAIN 5 OFF ON LTC4300A-3 ENABLE GND 4300A-3 TA01 SDAOUT 200ns/DIV 4300A TA02 4 sn4300a3 4300a3fs 1 LTC4300A-3 U W W W ABSOLUTE AXI U RATI GS (Note 1) VCC to GND .................................................... - 0.3 to 7V VCC2 to GND .................................................. - 0.3 to 7V SDAIN, SCLIN, SDAOUT, SCLOUT ................. - 0.3 to 7V ENABLE ......................................................... - 0.3 to 7V Operating Temperature Range LTC4300A-3C ......................................... 0C to 70C LTC4300A-3I ...................................... - 40C to 85C Storage Temperature Range MSOP ............................................... - 65C to 150C DFN .................................................. - 65C to 125C Lead Temperature (Soldering, 10 sec) MSOP Only ....................................................... 300C U W U PACKAGE/ORDER I FOR ATIO ORDER PART NUMBER TOP VIEW VCC2 1 SCLOUT 2 SCLIN 3 8 9 GND 4 VCC 7 SDAOUT 6 SDAIN 5 ENABLE DD PACKAGE 8-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 9) PCB CONNECTION IS OPTIONAL LTC4300A-3CDD LTC4300A-3IDD DD PART MARKING* LBHG LBHG ORDER PART NUMBER TOP VIEW VCC2 SCLOUT SCLIN GND 1 2 3 4 8 7 6 5 LTC4300A-3CMS8 LTC4300A-3IMS8 VCC SDAOUT SDAIN ENABLE MS8 PART MARKING MS8 PACKAGE 8-LEAD PLASTIC MSOP TJMAX = 125C, JA = 200C/W LTBHD LTBHF Consult LTC marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specfications are at TA = 25C. VCC = 2.7V to 5.5V, VCC2 = 2.7V to 5.5V, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Power Supply VCC Positive Supply Voltage 2.7 5.5 V VCC2 Card Side Supply Voltage 2.7 5.5 V ISD Supply Current in Shutdown Mode IVCC1 VCC Supply Current VSDAIN = VSCLIN = 0V, VCC1 = VCC2 = 5.5V IVCC2 VCC2 Supply Current VSDAOUT = VSCLOUT = 0V, VCC1 = VCC2 = 5.5V VENABLE = 0V 20 A 3 4.1 mA 2.1 2.9 mA Start-Up Circuitry SDA, SCL Floating 0.8 1.0 1.2 V 50 95 150 s 0.5 * VCC 0.9 * VCC V 1 A VPRE Precharge Voltage tIDLE Bus Idle Time VEN ENABLE Threshold Voltage VDIS Disable Threshold Voltage ENABLE Pin IEN ENABLE Input Current ENABLE from 0V to VCC tPHL ENABLE Delay, On-Off 10 ns tPLH ENABLE Delay, Off-On 95 s 0.1 * VCC 0.5 * VCC 0.1 V sn4300a3 4300a3fs 2 LTC4300A-3 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specfications are at TA = 25C. VCC = 2.7V to 5.5V, VCC2 = 2.7V to 5.5V, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP 1 2 0 100 MAX UNITS Rise-Time Accelerators IPULLUPAC Transient Boosted Pull-Up Current Positive Transition on SDA, SCL, VCC = 2.7V, VCC2 = 2.7V, Slew Rate = 1.25V/s (Note 2) mA Input-Output Connection VOS Input-Output Offset Voltage 10k to VCC on SDA, SCL, VCC = 3.3V (Note 3), VCC2 = 3.3V, VIN = 0.2V fSCL, SDA Operating Frequency Guaranteed by Design, Not Subject to Test CIN Digital Input Capacitance Guaranteed by Design, Not Subject to Test VOL Output Low Voltage, Input = 0V SDA, SCL Pins, ISINK = 3mA, VCC = 2.7V, VCC2 = 2.7V ILEAK Input Leakage Current SDA, SCL Pins = VCC = 5.5V, VCC2 = 5.5V 0 0 175 mV 400 kHz 10 pF 0.4 V 5 A 400 kHz Timing Characteristics fI2C I2C Operating Frequency (Note 4) 0 tBUF Bus Free Time Between Stop and Start Condition (Note 4) 1.3 s thD,STA Hold Time After (Repeated) Start Condition (Note 4) 0.6 s tsu,STA Repeated Start Condition Setup Time (Note 4) 0.6 s tsu,STO Stop Condition Setup Time (Note 4) 0.6 s thD, DAT Data Hold Time (Note 4) 300 ns tsu, DAT Data Setup Time (Note 4) 100 ns tLOW Clock Low Period (Note 4) 1.3 s tHIGH Clock High Period (Note 4) 0.6 s tf Clock, Data Fall Time (Notes 4, 5) 20 + 0.1 * CB 300 ns tr Clock, Data Rise Time (Notes 4, 5) 20 + 0.1 * CB 300 ns Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: IPULLUPAC varies with temperature and VCC voltage, as shown in the Typical Performance Characteristics section. Note 3: The connection circuitry always regulates its output to a higher voltage than its input. The magnitude of this offset voltage as a function of the pullup resistor and VCC voltage is shown in the Typical Performance Characteristics section. Note 4: Guaranteed by design, not subject to test. Note 5: CB = total capacitance of one bus line in pF. sn4300a3 4300a3fs 3 LTC4300A-3 U W TYPICAL PERFOR A CE CHARACTERISTICS Input-Output High to Low Propagation Delay vs Temperature ICC vs Temperature 5.3 12 100 5.2 VCC = 2.7V VCC = 5.5V 5.1 4.8 4.7 VCC = 2.7V 4.6 4.5 IPULLUPAC (mA) t PHL (ns) ICC (mA) VCC = 3.3V 4.9 60 40 VCC = 5.5V 20 -25 0 25 50 TEMPERATURE (C) 75 0 -50 100 -25 0 25 50 TEMPERATURE (C) 6 VCC = 3V 4 VCC = 2.7V 75 4300-3 G01 100 0 -50 -25 0 25 50 TEMPERATURE (C) 75 100 4300-3 G03 4300-3 G02 Connection Circuitry VOUT - VIN 300 8 2 CIN = COUT = 100pF RPULLUPIN = RPULLUPOUT = 10k 4.4 VCC = 5V 10 80 5.0 4.3 -50 IPULLUPAC vs Temperature ISD vs Temperature 35 TA = 25C VIN = 0V 30 250 VCC = 5.5V 200 ISD (A) VOUT - VIN (mV) 25 150 VCC = 5V 100 20 15 10 VCC = 3.3V 50 0 VCC = 2.7V 5 0 10,000 20,000 30,000 RPULLUP () 40,000 4300-3 G04 0 -50 -25 50 25 0 TEMPERATURE (C) 75 100 4300A G05 sn4300a3 4300a3fs 4 LTC4300A-3 U U U PI FU CTIO S VCC2 (Pin 1): Card Supply Voltage. This is the supply voltage for the devices on the card I2C busses. Connect pull-up resistors from SDAOUT and SCLOUT to this pin. Place a bypass capacitor of at least 0.01F close to this pin for best results. SCLOUT (Pin 2): Serial Clock Output. Connect this pin to the SCL bus on the card. SCLIN (Pin 3): Serial Clock Input. Connect this pin to the SCL bus on the backplane. GND (Pin 4): Device Ground. Connect this pin to a ground plane for best results. ENABLE (Pin 5): Digital CMOS Threshold Input. Grounding this pin puts the part in a low current mode. It also disables the rise-time accelerators, disables the bus discharge circuitry, isolates SDAIN from SDOUT and isolates SCLIN from SCLOUT. For active operation, drive this pin to VCC. If this feature is unused, tie to VCC. Since ENABLE is VCC referenced, do not connect to VCC2 or pull up to VCC2. SDAIN (Pin 6): Serial Data Input. Connect this pin to the SDA bus on the backplane. SDAOUT (Pin 7): Serial Data Output. Connect this pin to the SDA bus on the card. VCC (Pin 8): Main Input Power Supply from Backplane. This is the supply voltage for the devices on the backplane I2C busses. Connect pull-up resistors from SDAIN and SCLIN to this pin. Place a bypass capacitor of at least 0.01F close to this pin for best results. Exposed Pad (Pin 9, DFN Package Only): Exposed Pad may by be left open or connected to device ground. sn4300a3 4300a3fs 5 LTC4300A-3 W BLOCK DIAGRA 2-Wire Bus Buffer and Hot SwapTM Controller VCC 8 2mA 2mA SLEW RATE DETECTOR 1 VCC2 SLEW RATE DETECTOR BACKPLANE-TO-CARD CONNECTION SDAIN 6 CONNECT 4 SDAOUT 7 CONNECT CONNECT 100k 100k 1V PRECHARGE 100k 100k 2mA 2mA SLEW RATE DETECTOR SLEW RATE DETECTOR BACKPLANE-TO-CARD CONNECTION SCLIN 3 CONNECT 2 SCLOUT + CONNECT - VCC2 - 1V + + - - STOP BIT AND BUS IDLE 0.5A + 0.55VCC/ 0.45VCC UVLO ENABLE 5 - 20pF 95s DELAY, RISING ONLY CONNECT CONNECT RD QB S 4 GND 0.5pF 4300A-3 BD Hot Swap is a trademark of Linear Technology Corporation. sn4300a3 4300a3fs 6 LTC4300A-3 U OPERATIO Start-Up When the LTC4300A-3 first receives power on its VCC pin, either during power-up or during live insertion, it starts in an undervoltage lockout (UVLO) state, ignoring any activity on the SDA and SCL pins until VCC rises above 2.5V. The part also waits for VCC2 to rise above 2V. This ensures that the part does not try to function until it has enough voltage to do so. During this time, the 1V precharge circuitry is also active and forces 1V through 100k nominal resistors to the SDA and SCL pins. Because the I/O card is being plugged into a live backplane, the voltage on the backplane SDA and SCL busses may be anywhere between 0V and VCC. Precharging the SCL and SDA pins to 1V minimizes the worst-case voltage differential these pins will see at the moment of connection, therefore minimizing the amount of disturbance caused by the I/O card. Once the LTC4300A-3 comes out of UVLO, it assumes that SDAIN and SCLIN have been inserted into a live system and that SDAOUT and SCLOUT are being powered up at the same time as itself. Therefore, it looks for either a stop bit or bus idle condition on the backplane side to indicate the completion of a data transaction. When either one occurs, the part also verifies that both the SDAOUT and SCLOUT voltages are high. When all of these conditions are met, the input-to-output connection circuitry is activated, joining the SDA and SCL busses on the I/O card with those on the backplane, and the rise time accelerators are enabled. Connection Circuitry Once the connection circuitry is activated, the functionality of the SDAIN and SDAOUT pins is identical. A low forced on either pin at any time results in both pin voltages being low. For proper operation, logic low input voltages should be no higher than 0.4V with respect to the ground pin voltage of the LTC4300A-3. SDAIN and SDAOUT enter a logic high state only when all devices on both SDAIN and SDAOUT release high. The same is true for SCLIN and SCLOUT. This important feature ensures that clock stretching, clock synchronization, arbitration and the acknowledge protocol always work, regardless of how the devices in the system are tied to the LTC4300A-3. Another key feature of the connection circuitry is that it provides bidirectional buffering, keeping the backplane and card capacitances isolated. Because of this isolation, the waveforms on the backplane busses look slightly different than the corresponding card bus waveforms, as described here. Input to Output Offset Voltage When a logic low voltage, VLOW1, is driven on any of the LTC4300A-3's data or clock pins, the LTC4300A-3 regulates the voltage on the other side of the part (call it VLOW2) to a slightly higher voltage, as directed by the following equation (typical): VLOW2 = VLOW1 + 75mV + (VCC/R) * 70 [] where R is the bus pull-up resistance in ohms. For example, if a device is forcing SDAOUT to 10mV where VCC = 3.3V and the pull-up resistor R on SDAIN is 10k, then the voltage on SDAIN = 10mV + 75mV + (3.3/10000) * 70 = 108mV (typical). See the Typical Performance Characteristics section for curves showing the offset voltage as a function of VCC and R. Propagation Delays During a rising edge, the rise-time on each side is determined by the combined pull-up current of the LTC4300A3 boost current and the bus resistor and the equivalent capacitance on the line. If the pull-up currents are the same, a difference in rise-time occurs which is directly proportional to the difference in capacitance between the two sides. This effect is displayed in Figure 1 for VCC = VCC2 = 3.3V and a 10k pull-up resistor on each side (50pF on one side and 150pF on the other). Since the output side has less capacitance than the input, it rises faster and the effective propagation delay is negative. There is a finite propagation delay through the connection circuitry for falling waveforms. Figure 2 shows the falling edge waveforms for the same VCC, pull-up resistors and equivalent capacitance conditions as used in Figure 1. An external NMOS device pulls down the voltage on the side with 150pF capacitance; the LTC4300A-3 pulls down the voltage on the opposite side, with a delay of 55ns. This delay is always positive and is a function of supply voltage, sn4300a3 4300a3fs 7 LTC4300A-3 U OPERATIO OUTPUT SIDE 50pF INPUT SIDE 150pF 0.5V/DIV 200ns/DIV 4300A-3 F01 INPUT SIDE 150pF 0.5V/DIV OUTPUT SIDE 50pF 200ns/DIV 4300A-3 F02 Figure 1. Input-Output Connection Low to High Transition Figure 2. Input-Output Connection High to Low Transition temperature and the pull-up resistors and equivalent bus capacitances on both sides of the bus. The Typical Performance Characteristics section shows tPHL as a function of temperature and voltage for 10k pull-up resistors and 100pF equivalent capacitance on both sides of the part. By comparison with Figure 2, the VCC = VCC2 = 3.3V curve shows that increasing the capacitance from 50pF to 100pF results in a propagation delay increase from 55ns to 75ns. Larger output capacitances translate to longer delays (up to 150ns). Users must quantify the difference in propagation times for a rising edge versus a falling edge in their systems and adjust setup and hold times accordingly. For example, assume an SMBus system with VCC = 3V, a 10k pull-up resistor and equivalent bus capacitance of 200pF. The rise-time of an SMBus system is calculated from (VIL(MAX) - 0.15V) to (VIH(MIN) + 0.15V), or 0.65V to 2.25V. It takes an RC circuit 0.92 time constants to traverse this voltage for a 3V supply; in this case, 0.92 * (10k * 200pF) = 1.84s. Thus, the system exceeds the maximum allowed rise-time of 1s by 84%. However, using the rise-time accelerators, which are activated at a DC threshold of below 0.65V, the worst-case rise-time is: (2.25V - 0.65V) * 200pF/1mA = 320ns, which meets the 1s rise-time requirement. Rise-Time Accelerators ENABLE Low Current Disable Once connection has been established, rise-time accelerator circuits on all four SDA and SCL pins are activated. These allow the user to choose weaker DC pull-up currents on the bus, reducing power consumption while still meeting system rise-time requirements. During positive bus transitions, the LTC4300A-3 switches in 2mA (typical) of current to quickly slew the SDA and SCL lines once their DC voltages exceed 0.6V. Using a general rule of 20pF of capacitance for every device on the bus (10pF for the device and 10pF for interconnect), choose a pull-up current so that the bus will rise on its own at a rate of at least 1.25V/s to guarantee activation of the accelerators. Grounding the ENABLE pin disconnects the backplane side from the card side, disables the rise-time accelerators, disables the bus precharge circuitry and puts the part in a near-zero current state. When the pin voltage is driven all the way to VCC, the part waits for data transactions on both the backplane and card sides to be complete (as described in the Start-Up section) before reconnecting the two sides. sn4300a3 4300a3fs 8 LTC4300A-3 U W U U APPLICATIO S I FOR ATIO Resistor Pull-Up Value Selection Live Insertion and Capacitance Buffering Application The system pull-up resistors must be strong enough to provide a positive slew rate of 1.25V/s on the SDA and SCL pins, in order to activate the boost pull-up currents during rising edges. Choose maximum resistor value R using the formula: Figures 3 and 4 illustrate the usage of the LTC4300A-3 in applications that take advantage of both its Hot Swap controlling and capacitance buffering features. In all of these applications, note that if the I/O cards were plugged directly into the backplane, all of the backplane and card capacitances would add directly together, making rise- and fall-time requirements difficult to meet. Placing a LTC4300A-3 on the edge of each card, however, isolates the card capacitance from the backplane. For a given I/O card, the LTC4300A-3 drives the capacitance of everything on the card and the backplane must drive only the capacitance of the LTC4300A-3, which is less than 10pF. R (VCC(MIN) - 0.6)(800,000)/C where R is the pull-up resistor value in ohms, VCC(MIN) is the minimum VCC voltage and C is the equivalent bus capacitance in picofarads (pF). In addition, regardless of the bus capacitance, always choose R 16k for VCC = 5.5V maximum, R 24k for VCC = 3.6V maximum. The start-up circuitry requires logic high voltages on SDAOUT and SCLOUT to connect the backplane to the card, and these pull-up values are needed to overcome the precharge voltage. BACKPLANE BACKPLANE CONNECTOR I/O PERIPHERAL CARD 1 VCC2 R7 10k C1 0.01F R8 10k VCC VCC SDAIN SDA SCLIN SCL C2 0.01F R1 10k R2 10k VCC2 SDAOUT CARD_SDA LTC4300A-3 SCLOUT CARD_SCL GND ENABLE R3 10k ENA1 I/O PERIPHERAL CARD 2 C3 0.01F VCC SDAIN SCLIN C4 0.01F R4 10k R5 10k VCC2 SDAOUT CARD2_SDA LTC4300A-3 SCLOUT CARD2_SCL GND ENABLE ENA2 R6 10k 4300A-3 F03 Figure 3. The LTC4300A-3 in a PCI Application Where All the Pins Have the Same Length. ENABLE Should be Held Low Until All Transients Associated with the Live Insertion Have Settled sn4300a3 4300a3fs 9 LTC4300A-3 U W U U APPLICATIO S I FOR ATIO BACKPLANE BACKPLANE CONNECTOR I/O PERIPHERAL CARD 1 R7 10k VCC SDA SCL ENA1 R8 10k STAGGERED CONNECTOR VCC2 C1 0.01F VCC SDAIN SCLIN C2 0.01F R1 10k R2 10k VCC2 SDAOUT CARD_SDA LTC4300A-3 SCLOUT CARD_SCL GND ENABLE R3 10k ENA2 STAGGERED CONNECTOR I/O PERIPHERAL CARD 2 C3 0.01F VCC SDAIN SCLIN C4 0.01F R4 10k R5 10k VCC2 SDAOUT CARD2_SDA LTC4300A-3 SCLOUT CARD2_SCL GND ENABLE R6 10k 4300A-3 F04 Figure 4. The LTC4300A-3 in a Custom Application. Making ENABLE the Shortest Pin Ensures that VCC and VCC2 Connect Before ENABLE is Allowed to Go High, Connecting the Card to the Backplane 5V to 3.3V Level Translator and Power Supply Redundancy voltage magnitudes of VCC and VCC2 with respect to each other. Systems requiring different supply voltages for the backplane side and the card side can use the LTC4300A-3, as shown in Figure 5. The pull-up resistors on the card side connect from SDAOUT to SCLOUT to VCC2, and those on the backplane side connect from SDAIN and SCLIN to VCC. The LTC4300A-3 functions for voltages ranging from 2.7V to 5.5V on both VCC and VCC2. There is no constraint on the This application also provides power supply redundancy. If the VCC2 voltage falls below its UVLO threshold, the LTC4300A-3 disconnects the backplane from the card, so that the backplane can continue to function. If the VCC voltage falls below its UVLO threshold and the VCC2 voltage remains active, hold ENABLE at ground to ensure proper operation. sn4300a3 4300a3fs 10 LTC4300A-3 U PACKAGE DESCRIPTION DD Package 8-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1698) R = 0.115 TYP 5 0.38 0.10 8 0.675 0.05 3.5 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 3.00 0.10 (4 SIDES) PACKAGE OUTLINE 1.65 0.10 (2 SIDES) PIN 1 TOP MARK (NOTE 6) (DD8) DFN 1203 0.75 0.05 0.200 REF 0.25 0.05 4 0.25 0.05 0.50 BSC 2.38 0.05 (2 SIDES) 1 0.50 BSC 2.38 0.10 (2 SIDES) 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON TOP AND BOTTOM OF PACKAGE MS8 Package 8-Lead Plastic MSOP (Reference LTC DWG # 05-08-1660) 3.00 0.102 (.118 .004) (NOTE 3) 0.254 (.010) 0.889 0.127 (.035 .005) 8 7 6 5 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) DETAIL "A" 0.52 (.0205) REF 0 - 6 TYP GAUGE PLANE 5.23 (.206) MIN 1 0.53 0.152 (.021 .006) 3.20 - 3.45 (.126 - .136) DETAIL "A" 0.42 0.038 (.0165 .0015) TYP 0.65 (.0256) BSC 1.10 (.043) MAX 2 3 4 0.86 (.034) REF 0.18 (.007) RECOMMENDED SOLDER PAD LAYOUT SEATING PLANE 0.22 - 0.38 (.009 - .015) TYP NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.65 (.0256) BSC 0.127 0.076 (.005 .003) MSOP (MS8) 0204 sn4300a3 4300a3fs Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LTC4300A-3 U TYPICAL APPLICATIO S VCC 5V R1 10k C2 0.01F R4 10k C1 0.01F SDA SDAIN VCC VCC2 SDAOUT SCL SCLIN LTC4300A-3 SCLOUT CARD_VCC, 3.3V R3 10k R2 10k CARD_SDA CARD_SCL 4300A-3 F05 ENABLE GND Figure 5. 5V to 3.3V Level Translator RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC1380/LTC1393 Single-Ended 8-Channel/Differential 4-Channel Analog Mux with SMBus Interface Low RON: 35 Single-Ended/70 Differential, Expandable to 32 Single or 16 Differential Channels LTC1427-50 Micropower, 10-Bit Current Output DAC with SMBus Interface Precision 50A 2.5% Tolerance Over Temperature, 4 Selectable SMBus Addresses, DAC Powers up at Zero or Midscale LTC1623 Dual High Side Switch Controller with SMBus Interface 8 Selectable Addresses/16-Channel Capability LTC1663 SMBus Interface 10-Bit Rail-to-Rail Micropower DAC DNL < 0.75LSB Max, 5-Lead SOT-23 Package LTC1694/LTC1694-1 SMBus Accelerator Improved SMBus/I2C Rise-Time, Ensures Data Integrity with Multiple SMBus/I2C Devices LT1786F SMBus Controlled CCFL Switching Regulator 1.25A, 200kHz, Floating or Grounded Lamp Configurations LTC1695 SMBus/I2C Fan Speed Controller in ThinSOTTM 0.75 PMOS 180mA Regulator, 6-Bit DAC LTC1840 Dual I2C Fan Speed Controller Two 100A 8-Bit DACs, Two Tach Inputs, Four GPI0 LTC4300A-1/LTC4300A-2 Hot Swappable 2-Wire Bus Buffer Preserves Data integrity Under Hot Swap Conditions, Provides Capacitive Buffering, Rise-Time Acceleration LTC4301 Supply Independent 2-Wire Bus Buffer Provides Capacitive Buffer, 3.3V to 5V Level Translation with Only the Card Bus VCC Supply LTC4301L Hot-Swappable 2-Wire Bus Buffer with Low Voltage Level Translation Level Translators, 1V Signals to Standard 3.3V and 5V Logic Rails LTC4302-1/LTC4302-2 Addressable I2C and SMBus Compatible Bus Buffers Provides Capacitive Buffering, Rise-Time Acceleration, and Input to Output Connection Control Using 2-Wire Bus Commands ThinSOT is a trademark of Linear Technology Corporation. sn4300a3 4300a3fs 12 Linear Technology Corporation LT/TP 0404 1K * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2004