Component Marking
Terminal Block Marking
Legend Plates
Signs
Cable Marking
Wire Marking
Name Plates
Logo Plates
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
2
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 3
Plotter VP 600 Basic
The VP 600 Basic base unit is an economy auxiliary plotter that has to be connected to a PC via a USB connection. It is a high speed
plotting device and enables plotting of different markers in one setting. The marker fixture and the plotter pen have to be inserted
manually before commencing the plotting operation. The base unit is controlled through a PC with the help of Vario Sign software (sold
separately). Manual available in English and Spanish.
The special design of the VP 600 Basic enables it to hold different markers from various manufacturers at the same time. It is also pos-
sible to write on relatively large markers with a maximum height of 10.5 mm.
Plotter VP 600 A3
The VP 600 A3 base unit is an advanced auxiliary plotter that has to be connected to a PC via a USB connection. It is a high speed
plotting device and enables plotting of different markers in one setting. The base unit is primarily controlled through a PC with the help
of Vario Sign software (sold separately). Manual available in English and Spanish.
The special design of the VP 600 A3 enables it to hold different markers from various manufacturers at the same time. It is also pos-
sible to write on relatively large markers with a maximum height of 10.5 mm.
VP 600 BASIC BASE UNIT (power supply and USB cable included) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000082
VARIOSIGN SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000022
FIXTURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 5-6
PEN AND INK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4
VP 600 A3 BASE UNIT (power supply and USB cable included) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000080
VARIOSIGN SIGN SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000022
FIXTURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .pages 5-6
PEN AND INK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 4
• Professionally marking of connectors, wires, cables,
equipment, cable ties, shrink tubing, labels and
signs of different sizes and materials, as well as
customer-specific items.
• Auto calibration
• Universal Power Supply 100-240V AC
• Control language HPGL
• Universal marking software (VarioSign) sold separately
• Marking area 273 x 305 mm
• Size: 18.5 x 18.9 x 6.1 in. (470 x 480 x 155 mm)
• Weight: 13.9 lbs.
• Basic features of plotter VP 600 Basic plus:
• Integrated and automated pen station.
Holds 4 different pens at the same time, for
fast and frequently changing applications.
• Built-in pen priming function
• Automatic recognition system for marking fixture /
plates ensures faster and easier handing of
frequently changing marking applications.
• Wide marking area 422 x 305 mm
• Size: 27.2 x 18.9 x 6.1 in. (690 x 480 x 155 mm)
• Weight: 18.3 lbs.
Product Width Order No.
EK Plotter Pen (red) 0.18 mm 35001018
EK Plotter Pen (white) 0.25 mm 35001025
EK Plotter Pen (yellow) 0.35 mm 35001035
EK Plotter Pen (brown) 0.50 mm 35001050
EK Plotter Pen (blue) 0.70 mm 35001070
EK Plotter Pen (orange) 1.00 mm 35001100
EK Ink Cartridge
5 cartridges, Black, 1 ml. each 35100006
EK Disposable Plotter Pen (red) 0.18 mm 35003018
EK Disposable Plotter Pen (white) 0.25 mm 35003025
EK Disposable Plotter Pen (yellow) 0.35 mm 35003035
EK Disposable Pen EDR (red) 0.18 mm 35003118
EK Disposable Pen EDR (white) 0.25 mm 35003125
EK Disposable Pen EDR (yellow) 0.35 mm 35003135
* 0.5 - 1.00mm versions available upon request, consult Altech.
EK Cleaning Set 35100010
(includes cleaning unit and pen cleaner)
EK Pen Cleaner (2 pieces, 2x10 ml) 35100008
EK pen Cleaner Bottle (1 piece, 1x30 ml) 35100012
Adapter for an Utra Fine Sharpie™ 35000501
Suction Ball 35100013
Service Kit 34000026
Plotter Pens
These “tubular-nib” pens are suitable for VP 600 Basic and VP 600
A3 and all current labeling and identification systems with HP pen-
holders. They are available in six tip widths identified by body color
- 0.18 mm, 0.25 mm, 0.35 mm, 0.50 mm, 0.70 mm, and 1.00 mm;
ink cartridge not supplied with pen. A recovery / storage stand is in-
cluded. Special variants for other systems are available on request.
Ink
These are easy to insert “tubular-nib” pen cartridges containing spe-
cial formulated black etching ink suitable for marking, identifying and
labeling various plastics. It is fast drying, smudge-proof, fade resist-
ant, and resistant to chemicals when used on suitable plastic mate-
rials. The ink formula prevents the plotter pens from clogging as
easliy when properly stored. A clogged plotter pen may recover itself
after a while by following the plotter pen handling and care instruc-
tions.
Disposable Pens
The disposable pens (etching) use the same special ink as used in the
ink cartridges. They deliver the same outstanding durability and print
quality as the standard plotter pens with the convenience of a dis-
posable pen. These pre-filled pens allow for fast, efficient and cost
effective printing without refilling ink or cleaning. They are available
in six tip widths identified by body color - 0.18, 0.25, 0.35, 0.50*,
0.70* and 1.00* mm.
Disposable Pens (EDR)
The disposable pens (EDR) use a non-etching ink for easier handling.
This is conveneint for users that do not print tags on a daily basis as
these pens almost never clog. The EDR pens are filled with perma-
nent ink which is fast drying. These pens should only be used on
plastic elements that will not be exposed to aggressive fluids. Not
suitable for use on Polycarbonate materials. They are avaialble in six
tip widths identified by body color - 0.18, 0.25, 0.35, 0.50*, 0.70*
and 1.00* mm.
Cleaning Set
It is an easy-to-use cleaning unit and a set of pen cleaners developed
specially for EK Pens. The cleaning unit enables the pens to be rinsed
thoroughly while preventing skin contact with cleaning fluid or ink.
The cleaning unit can be used for up to ten cleaning cycles. The nec-
essary precautions must be taken when disposing of cleaning fluid,
the cleaning unit can be reused. The set includes 2 pen cleaner bot-
tles, 2x10 ml which can be purchased separately as well for contin-
ued use of the cleaning unit.
Pen Cleaner
This cleaning solution comes in easy to handle cartridges and is used
in conjunction with the cleaning unit. A standard pack consists of two
pen cleaner cartridges. Cleaning can be performed on standard re-
fillable pens only. A 30 ml bottle is also available for refilling the car-
tridges.
Adapter
This adapter allows the use of Sharpie™ Ultra Fine felt tip pens in-
stead of standard plotter pens.
Suction Ball
The "suction ball" is a helpful tool to bring a slightly clogged
disposable or refillable plotter pen back to life. The suction can prime
a slightly clogged plotter pen from the vacuum created within the
"ball". 5 replacement tips are included with each suction ball.
Service Kit for VP 600 A3
The service kit includes 4 plotter pen station inserts, 1 wrench, 12
single primer plates.
Altech Corp.
®
• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
4
Cleaning Unit Pen Cleaners
Description Part No.
ABB / Entrelec
ABB Entrelec universal - RC/RCT quarter size 34902063
ABB Entrelec RC 510A, 610A, 810A 34902114
ABB Entrelec RC 510B, 610B, 810B 34902102
ABB Entrelec RB-RBP 5-12 34902086
ABB Entrelec BA 5-50 34902100
ABB Entrelec PIB 34902101
ABB Entrelec RCCV 34902038
ABB Entrelec BS / ILS / ILS-H 34902106
ABB Entrelec PAM -PAM 21515/21520,
PAM 43015/43020 34902135
ABB Entrelec R310 34902174
ABB Entrelec RTM 34902088
ABB Entrelec MC 512/612/812PA 34902190
Set of sticky pads ( 8 pcs) for RC/RCT 34910000
Allen Bradley
Allen Bradley Universal (old marker cards) 34902046
Allen Bradley 1492 Universal 34902141
Altech
Altech MT2G 34902191
Altech MT 2n - MT 4n, MT 7.5, MT 20, MT 25 34902081
Altech MT 5 - MT 15 34902001
Altech MT 9F 34902057
Altech CA 509-G3 34902079
Altech Group marker G1, G2, G4 34902080
ASI
ASI Universal 34902172
C3controls
c3controls WTB2-M 2 34902081
c3controls WTB2-M 5 - M 15 34902001
c3controls WTB2-M 9 34902057
Conexel
Dekafix 5 34902146
Connectwell
Connectwell K2G 34902191
Connectwell K2n - K4n, K7.5, K 20, K25 34902081
Connectwell K5 - K15 34902001
Connectwell K9F 34902057
Connectwell CA 509-G1/G2/G4 34902080
Connectwell CA 509-G3 34902079
Conta Clip
Conta Clip BSTR / SB 34902002
Conta Clip SB 8/10 34902003
Conta Clip AD 1/5 N SB 7.5 34902089
Conta Clip ADQ 34902090
Conta Clip KBH-S4 34902091
Conta Clip AD 1/6N, AD 1/5, AD 1/6, AD 1/8 34902092
Conta Clip AD 1/12 N 34902093
Conta Clip MC BSTR / MC SB 34902108
Conta Clip ZSchT 6 / SchT 9 / SchT 10 34902109
Conta Clip KBH 3 stripe 34902011
Conta Clip KBH 5 stripe 34902014
Conta Clip KBH 10 34902016
Conta Clip KBH-S stripe 34902024
Conta Clip KBH-S single 34902023
Conta Clip BST 8, ESO, GKE, Label 34902106
DECA
DECA W4-W8 34902197
Set of sticky pads for DECA W4-W8 (8 pcs.) 34910020
Degson
Degson ZB 34902159
Degson TSZB4 34902160
Degson TZB4 34902161
Degson DEK4, 5, 6 34902162
Degson ZW5 34902163
Dinkle
Universal 34902145
Description Part No.
Elektro
Elektro RSA 12 34902173
elmex
elmex card 10 by 10 34902061
elmex KN 5,5; 6,5; 8 34902077
elmex U5-10 34902157
elmex KN10, KN12 34902158
General Marking
General Marking TDM 34902166
General Marking MG-TPM 34902170
Grafoplast
Grafoplast 5I2KTB 34902211
Idento
Idento EEB / LEB 34902106
Klemsan
Plot-PLA 34902124
Plot-PL E (Universal engraving and plot support
plate half size, A4) 34902106
Plot PL (Universal engraving and plot support
plate full size A3) 34902107
Plot-PL DB 34902136
Plot-PL DB4 34902175
Plot-PL DB4.5x7.5 34902194
Plot-PL DB5 34902138
Plot-PL DB10/8, 10/10 34902165
Plot-PL KBE 34902196
Plot-PL KE 34902137
Legrand
Wire Marker Memocab 34902119
Terminal Blocks Legrand 34902120
Terminal Blocks other manufacturer 34902121
Cable markers Duplix 34902122
Self adhesive markers for equipment 34902123
Lumberg
Lumberg ZBS 34902180
Moeller
Moeller Typ XA 34902006
Moeller Typ XB, M22-XST 34902007
Morsettitalia
Morsettitalia 42090 34902113
Morsettitalia 42091 34902179
Morsettitalia 43192, 43196, 43541 34902112
Morsettitalia 43899T43 34902176
Morsettitalia Strips 6, 8, 10, 12 mm 34902202
Morsettitalia 438MFC 34902212
murrplastik
murrplastik MP-400 (KS 4/xx) 34902008
murrplastik MP-401 (KES, KLG, KMR, KPX, KS,
KSA,KSF etc.) 34902009
murrplastik BS, KSF 10x8, KSN 34902082
murrplastik KDE 34902111
murrplastik KNDW 34902110
murrplastik KPX ZS 34902099
murrplastik KS 5/10 34902083
murrplastik KSE 0.75/10 ; KSE 1.5/10 34902084
murrplastik KSE 1,5/18 34902085
murrplastik KET 34902114
murrplastik DM 34902106
Continued on next page.
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 5
Description Part No.
PARTEX
Partex PA+02 / PAZ+02 strip 34902011
Partex PA+1 / PAZ+1 strip 34902014
Partex PA+2 single 34902016
Partex PC10 / PC20 34902019
Partex PC30 / PC40 34902020
Partex PC50 34902018
Partex PEM 34902022
Partex PK-2 single 34902023
Partex PK2 / PVC strip 34902024
Partex PK2 Zerex strip 34902025
Partex PS 34902028
Partex TX 34902029
Partex TX 61 34902118
Partex PFC 34902070
Partex PN endless strip 34902026
Partex PN (21) endless strip 34902139
Partex POH 34902027
Partex PFA20018TK9 34902106
Set of Sticky Pads for Partex PFC (4 pcs.) 34910008
Set of Sticky Pads for Partex POH (8 pcs.) 34910007
Phoenix
Phoenix Contact ZBM 34902039
Phoenix Contact ZB 34902047
Phoenix Contact ZBFM 34902049
Phoenix Contact ZBF, ZBN 34900050
Phoenix Contact BNZ 34902051
Phoenix Contact BN-ZB 34902052
Phoenix Contact SS-ZB 34902053
Phoenix Contact LBHZ 34902054
Phoenix Contact PAB 34902055
Phoenix Contact GPE (quarter size plate) 34902071
Phoenix Contact GPE (half size plate, A4) 34902106
Phoenix UC-TM/WMC 3.1 34902129
Phoenix UC-WMC-4.4 34902130
Phoenix UC-WMC7.5 34902131
Phoenix UC-TMF/UC-WMT 34902132
Phoenix UC-SIE/UC1-TM 34902133
Phoenix UC-EMLP 34902134
Phoenix UC-WM 34902164
Phoenix UCT-TM 34902195
Phoenix UCT-TMF/UCT-WMT 34902193
Set of Sticky Pads for Phoenix ZBFM (8 pcs.) 34910021
RAAD
RAAD Universal 5-10 34902192
RELPOL
RELPOL TR/ERSCE 34902209
RELPOL GS4-0035 34902208
RELPOL GZP-0035 34902207
RELPOL GZT-0035/GZT80-0035 34902206
RELPOL PIR 34902210
Scheider Electric
Schneider Electric KN-300 34902168
Schneider Electric BMP/01 34902198
Schneider Electric BMP/02 34902199
Schneider Electric BMP/03 34902106
SES
SES PLIO M-012 34902037
SES PLIO 14-1177 34902038
SES 27 x 18 34902106
Set of Sticky Pads for SES PLIO 14-1177 (8 pcs.) 34910016
Description Part No.
Siemens
Siemens S7 insert plates Universal 34902140
Siemens Tag 22x22 / 17x28 34902067
Siemens Sirius 10x7, 20x7 34902073
Sprecher + Schuh
Sprecher + Schuh Universal 34902046
Sprecher + Schuh V7-MP 34902188
Sprecher + Schuh V7-MP5 34902193
UPUN
UPUN BB 34902185
UPUN JB5 34902183
UPUN JBM5 34902184
UPUN KB 34902185
UPUN UBFM 34902186
UPUN ZB 34902181
UPUN ZBM4 34902182
Set of Sticky Pads for UPUN KB (3 pcs.) 34910017
Wago
WAGO WMB 4/4,2/5 34902041
WAGO WSB 4 34902074
WAGO WSB 5/5,2 34902075
WAGO WSB mini 34902076
WAGO WSB micro 34902201
WAGO Group marker carrier 34902078
WAGO Marking Strip 34902087
WAGO Marker tags 34902094
WAGO WTB 34902096
WAGO WCB 34902097
WAGO WMB inline 34902098
WAGO 210-345 34902106
Set of sticky pads (12 pcs) for Top Job (Marking Strip) 34910002
Weidmüller / Rockwell (Allen Bradley)
Weidmüller MultiCard Universal 34902045
Weidmüller MultiCard SF4-6 / SFC3 34902044
Weidmüller MultiCard WAD 34902169
Weidmüller Dekafix (non-Multicard) 34902167
Set of sticky pads (6 pcs) for Multicard Universal 34910001
Wieland
Wieland Universal 34902043
Wieland BZ/WKF 1,5 04.243.2053.0 34902047
Wieland BZ/WKF 1,5/10 Z4.243.2053.0 34902049
Wieland Steierform 6 x 15, 10 x 20 34902106
Set of sticky pads (9 pcs) for Wieland Universal 34910006
Woertz
Woertz Universal 34902046
Zoloda
CW 5/6 34902142
IB Universal 34902177
ICAB 00-02 34902143
ICAB 03 34902144
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
6
Handling and care of the EK-Team plotter pens for the universal EK-Team marking system.
For the state of the art universal marking system by EK-team, the manufac-
ture is supplying a fast drying and etching ink that is required for marking
plastic material within the control and automation industry. Due to these spe-
cial properties of the ink, these plotter pens require much more care than a
regular marking pen. Therefore EK-Team designed some helpful tools to
keep your EK-team plotter pen in tip top shape.
Recovery and Storage Stand
This stand is designed to keep the plotter pen in an upright position, when
not used with the marking system. The upright position allows the plotter pen
to recover and to be properly stored. It is recommended to store plotter pens
that will be idle for a few hours in a dry and cool location, preferably in the
refrigerator. The recovery and storage stand accommodates easy storage
and handling.
Call Altech for your free recovery and storage stand.
Part. No. 35000100
Suction Ball
The "suction ball" is a helpful tool to bring a slightly clogged disposable or re-
fillable plotter pen back to life. The suction can unclog a slightly clogged plot-
ter pen from the vacuum created within the "ball". This additional tool can be
very helpful in addition to the already available cleaning kit (Cat. No.
35100010) for the refillable plotter pens. 5 replacement tips are included with
each suction ball.
Part. No. 35100013
Pen Cleaning
CLEANING UNIT
It is an easy-to-use cleaning unit developed specially for refillable pens. The cleaning unit enables the pens
to be rinsed thoroughly while preventing skin contact with cleaning fluid or ink. The cleaning unit can be used
for up to ten cleaning cycles. The necessary precautions must be taken when disposing of cleaning fluid,
the cleaning unit can be reused.
PEN UNIT
This cleaning solution comes in easy to handle cartridges and is used in conjunction with the cleaning unit.
A standard pack consists of two pen cleaner cartridges. Cleaning can be performed on standard refillable
pens only.
Cleaning Set Part. No. 35100010
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 7
Disposable
Pen
Rellable
Pens
Pen Stand
Refrigerate pens when
not in use for long
periods of time.
Engraver VP/E 600 Add-on Unit
The engraving unit was specifically de-
signed to be used with the VP 600
plotters. Changing back and forth be-
tween the pen-plotter and the engraver
is easy. The engraver is meant to en-
grave plastic signs on double sided
material, pre-cut or blank sheets, leg-
end plates, push button inlays, etc.
Any kind of design software can be
used, e.g. Corel Draw, to create cus-
tom logos, symbols as signs, that
saves the creation as a HPL plot file
(HPGL). The add-on unit consists of an
engraving head, spindle, controller,
vaccum for a clean engraving process;
as well as all cable and necessary con-
nection parts. The engraver unit is con-
trolled by the VarioSign software for
ease of use and design flexibility.
Vacuum Cleaner Bag
Replacement bags for the VP/E 600
engraver’s vacuum cleaner
Engraver Fixtures
The universal support plates are used
to hold the engraving materials pre-
cisely in place. Five sizes are offered
for holding plastic sheets, aluminum
and brass plates, etc.. The surface ma-
terial is self sticking to hold different
materials in place during the engraving
process.
VP/E 600 ENGRAVER UNIT (VP 600 REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34000083
VACUUM CLEANER BAG, SET OF 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35020000
FULL SIZE, A3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34902107
HALF SIZE, A4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34902106
1/4 FIXTURE, 30 X 100mm, 9 FOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34902115
1/4 FIXTURE, 60 X 100mm, 4 FOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34902116
1/4 FIXTURE, 90 X 100mm, 3 FOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34902117
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
8
Engraving needle 15° - 0.2 mm 35010003
Engraving needle 15° - 0.3 mm 35010002
Engraving needle 15° - 0.4 mm 35010001
Engraving needle 15° - 0.5 mm 35010000
Engraving needle 15° - 0.7 mm 35010004
Engraving needle 15° - 1.0 mm 35010005
Engraving needle 15° - set of 0.2; 0.3; 0.4; 0.5; 0.7; 1.0 mm 35010006
Engraving needle 36° - 0.2 mm 35010015
Engraving needle 36° - 0.3 mm 35010016
Engraving needle 36° - 0.4 mm 35010017
Engraving needle 36° - 0.5 mm 35010018
Engraving needle 36° - 0.7 mm 35010019
Engraving needle 36° - 1.0 mm 35010020
Engraving needle 60° - 0.2 mm 35010021
Engraving needle 60° - 0.3 mm 35010022
Engraving needle 60° - 0.4 mm 35010023
Engraving needle 60° - 0.5 mm 35010024
Engraving needle 60° - 0.7 mm 35010025
Engraving needle 60° - 1.0 mm 35010026
Engraving needle 90° - 0.2 mm 35010027
Engraving needle 90° - 0.3 mm 35010028
Engraving needle 90° - 0.4 mm 35010029
Engraving needle 90° - 0.5 mm 35010010
Engraving needle 90° - 0.7 mm 35010011
Engraving needle 90° - 1.0 mm 35010012
Engraving needle 35° - 0.2 mm* 35010013
Engraving needle 35° - 0.4 mm* 35010014
Double tooth cutter fishtail 0.5 mm 35010030
Double tooth cutter fishtail 0.6 mm 35010031
Double tooth cutter fishtail 0.8 mm 35010032
Double tooth cutter fishtail 1.00 mm 35010033
Double tooth cutter fishtail 1.20 mm 35010034
Double tooth cutter fishtail 1.40 mm 35010035
Double tooth cutter fishtail 1.60 mm 35010036
Double tooth cutter fishtail 2.00 mm 35010037
Double tooth cutter fishtail 2.40 mm 35010038
Double tooth cutter fishtail 3.00 mm 35010039
Engraving Needle 90° for anodized aluminum 1.00 mm 35010043
Engraving Needles for:
Plastic Material
Metal
Engraving Needles
These engraving needles are to be
used with the VP/E 600 engraver. They
are available in different angles and tip
widths depending on shape and mate-
rial that is being engraved. Needles for
metal engraving are available, the dou-
ble tooth cutter with fishtail can dip into
metal quite easily to speed the grind-
ing performance.
* Recommended needles for
stainless steel
Please note that for stainless steel,
only a surface engraving is possible,
not deep like in plastic material.
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 9
TITLE - Title to the products of ALTECH shall remain with ALTECH
until payment is made in full by Customer. Such reservation of title is for the
purpose of securing the purchase price and shall not relieve Customer of
the duty to inspect the products upon receipt, to notify ALTECH of any de-
ficiencies or defects, and to exercise due care in the use, installation, op-
eration, and maintenance of the products when on the premise of the
Customer or under the control of the Customer. Notwithstanding any reser-
vation of title by ALTECH, risk of loss shall pass to customer at any time
of shipment.
SHIPMENT AND DELIVERY - All orders for destination in the mainland
United States (less Hawaii, Alaska and non-continental United States pos-
sessions) will be shipped F.O.B. Flemington, N.J. All destination, shipping
and other charges shall be paid by the Customer in accordance with AL-
TECH’s then current shipping and billing practices.
Delivery dates given in the acceptance of any order are approximate.
ALTECH shall not be liable for delays in delivery or in performance due to
causes beyond its reasonable control including acts of God, acts of Cus-
tomer, acts of civil or military authority, fires, strikes or other labor distur-
bances, war, riot or delays in transportation. In the event of such delay, the
date of delivery or performance shall be extended for a period equal to the
time lost by reason of the delay.
PRICE - PRICES in any ALTECH publication are subject to change
without prior notification. Catalog prices are based on prices published in
the current price list. All written quotations are valid for thirty (30) days from
the date of quotation. Customer shall pay all sales, use, excise or similar
taxes whenever ALTECH must itself pay and/or collect such tax from Cus-
tomer arising out of the sale.
PAYMENT - Customer agrees to make payment within thirty (30) days
of date of the invoice from ALTECH. Customer agrees to pay a late pay-
ment charge of one and one-half percent (1.5% per month, or the maxi-
mum late payment charge permitted by applicable law, whichever is less,
on any unpaid amount for each calendar month (or fraction thereof) that
such payment is in default. Orders amounting to less than $100.00 will be
billed at $100.00 plus freight. Full carton purchases are required. In the
event of referral to an attorney for collection, reasonable attorney’s fees for
collection of the overdue amount shall be paid by Customer. In the event
payment is not received within 30 days from the date of invoice, any dis-
count shall be cancelled and the full list price will be due.
LIMITED WARRANTY - ALTECH warrants to Customer that the equip-
ment purchases shall be free from defects in material and workmanship
under normal use and service for a period of one year from shipment.
Written notice as an explanation of the circumstances of any claim that
the equipment has proved defective in material or workmanship shall be
given promptly by the Customer to ALTECH.
ALTECH will not be liable for any misuse, improper operations, im-
proper installation, improper maintenance, alteration, modification, acci-
dent or unusual degradation of the equipment or parts due to an unsuitable
installation environment.
No representation of other affirmation of facts, including but not lim-
ited to statements regarding capacity, suitability for use or performance of
the equipment, shall be or be deemed to be a warranty or representation
by ALTECH for any purpose, nor give rise to any liability or obligation of AL-
TECH whatsoever.
Customer’s sole and exclusive remedy in the event of breach of war-
ranty, as set forth herein, is expressly limited to (1) the correction of the de-
fect by adjustment, repair, modification, or replacement, or (2) issuance of
a credit or refund of the purchase price for the defective equipment at AL-
TECH’s election and sole expense.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT,
THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED IN-
CLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY EXTENDS ONLY TO THE CUSTOMER FROM AL-
TECH OR ITS AUTHORIZED DISTRIBUTOR.
LIMITATION OF LIABILITY - IN NO EVENT, SHALL ALTECH BE LI-
ABLE FOR LOSS OF PROFITS, INDIRECT, SPECIAL, CONSEQUEN-
TIAL OR OTHER SIMILAR DAMAGES ARISING OUT OF ANY BREACH
OF THIS AGREEMENT OR OBLIGATIONS UNDER THE AGREEMENT.
ALTECH SHALL NOT BE LIABLE FOR ANY DAMAGES CAUSED BY
DELAY IN SHIPMENT, INSTALLATION OR FURNISHING OF EQUIP-
MENT OR SERVICES UNDER THIS AGREEMENT.
No action arising out of any claimed breach of this Agreement may be
brought by either party more than two (2) years after the cause of action
has accrued.
PATENT INDEMNITY - ALTECH shall defend or settle any suit or pro-
ceeding brought against Customer based on a claim that any equipment
made to ALTECH design and furnished hereunder constitutes an in-
fringement of any existing United States patent, provided (ALTECH) is no-
tified promptly in writing and is given complete authorization and
information required for the defense, and ALTECH shall pay all damages
and costs awarded against Customer, but shall not be responsible for any
costs, expense or compromise incurred or made by Customer without AL-
TECH’s prior written consent. If any equipment is in ALTECH’s opinion
likely to or does become the subject of a claim for patent infringement, AL-
TECH may at its option and expense procure for Customer the right to
continue using the device, modify it to become non-infringing, but in the
event ALTECH is not reasonably able to modify, substitute, or otherwise
procure for Customer the right to continue using it, ALTECH will remove
such equipment and refund to Customer the amount paid in excess of a
reasonable rental for past use.
ALTECH shall not be liable for any infringement or claim based upon
use of the equipment in combination with other equipment not supplied by
ALTECH or with modifications made by Customer.
The foregoing states the entire liability of ALTECH to Customer arising
from patent infringement.
SELLER’S REMEDIES - Should Customer fail to make any payment
within ten (10) days of its due date, or fail to perform any other of the Cus-
tomer’s obligation hereunder upon thirty (30) days written notice, or should
Customer be or become insolvent or be a party to any bankruptcy re-
ceivership proceeding prior to full payment of all amounts payable here-
under, ALTECH may: (a) with or without demand or notice to customer
declare the entire amount unpaid immediately due and payable; (b) enter
upon the premises where the equipment may be found and remove it (Cus-
tomer shall assemble the equipment and make it available to ALTECH at
a place reasonably convenient to both parties and shall permit and assist
ALTECH in effecting the retaking and removal of the equipment); and (c)
sell any or all the equipment as permitted under applicable law, applying
the proceeds of the sale to payment of the expenses of retaking, repairing
and selling the equipment, reasonable attorney fees and to the satisfac-
tion of all indebtedness then due and unpaid under this Agreement. Any
surplus shall be paid to Customer and any deficiency shall be paid to AL-
TECH by Customer.
The remedies provided herein shall be cumulative and in addition to all
other remedies provided by law or equity or under the Uniform Commer-
cial Code.
GOVERNING LAW - This agreement will be governed by the Laws of
the State of New Jersey.
GENERAL - This Agreement shall only become effective and binding
when either (a) it has been accepted and executed by an authorized rep-
resentative of ALTECH, or (b) the equipment has been shipped to Cus-
tomer, with or without acceptance in writing hereon. Notice of acceptance
is hereby waived by Customer. Customer hereby acknowledges receipt of
a true and complete copy hereof.
No addition to or modification of any of the Terms and Conditions of
Sale as they appear herein shall be binding upon ALTECH unless signed
in writing by duly authorized representative of ALTECH in Flemington, N.J.
Typographical and clerical errors in quotations, orders and acknowl-
edgments are subject to correction.
This Agreement is not assignable without the prior written consent of
ALTECH. Any attempt to assign any of the rights, duties or obligations of
this Agreement without such consent is void.
If any provision or provisions of this Agreement shall be held to be in-
valid, illegal or unenforceable, the validity, legality and enforceability, of the
remaining provisions shall not in any way be affected or impaired thereby.
ALTECH is not responsible for failure to fulfill its obligation under this
Agreement due to causes beyond its control, or except as agreed herein.
THE CUSTOMER ACKNOWLEDGES THAT HE HAS READ THE
AGREEMENT, UNDERSTANDS IT, AND AGREES TO BE BOUND BY
ITS TERMS AND CONDITIONS. FURTHERMORE, THE CUSTOMER
AGREES THAT IT IS THE COMPLETE AND EXCLUSIVE STATEMENT
OF THE AGREEMENT BETWEEN THE PARTIES, WHICH SUPER-
SEDES ALL PROPOSALS OR PRIOR AGREEMENTS, ORAL OR WRIT-
TEN, EXPRESSED OR IMPLIED, AND ALL OTHER COMMUNICATIONS
BETWEEN THE PARTIES RELATING TO THE SUBJECT MATTER OF
THIS AGREEMENT.
STANDARD TERMS AND CONDITIONS OF SALE
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com
10
Altech Corp.®• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 • www.altechcorp.com 11
Service Center
Service Center
Phone/Fax: 908-806-7035
Phone/Fax: 908-806-7035
•
•Warranty
Warranty
•
•Service
Service
•
•Repair
Repair
•
•VP100
VP100
•
•VP500
VP500
•
•VE500
VE500
• VP600
• VP600
•
•VP/E600
VP/E600
•
•OEM branded similar models
OEM branded similar models
Altech Corporation
35 Royal Road
Flemington, NJ 08822-6000
Phone (908) 806-9400
Fax (908) 806-9490
www.altechcorp.com
Altech Corp.® 280-062016-3M
PRINTED AUGUST 2016
