The mark <R> shows major revised points.
The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.
6-PIN DIP, 600 V BREAK DOWN VOLTAGE
NORMALLY OPEN TYPE
1-ch Optical Coupled MOS FET
Solid State Relay
OCMOS FET
PS7160-1A,PS7160L-1A
Document No. PN10289EJ02V0DS (2nd edition)
Date Published July 2006 NS CP(K)
−NEPOC Series−
1996, 2006
DESCRIPTION
The PS7160-1A and PS7160L-1A are solid state relays containing GaAs LEDs on the light emitting side (input side)
and MOS FETs on the output side.
They are suitable for analog signal control because of their low offset and high linearity.
The PS7160L-1A has a surface mount type lead.
FEATURES
• 1 channel type (1 a output)
• Low LED operating current (IF = 2 mA)
• Designed for AC/DC switching line changer
• Small package (6-pin DIP)
• Low offset voltage
• Ordering number of taping product: PS7160L-1A-E3, E4: 1 000 pcs/reel
• Pb-Free product
• Safety standards
• UL approved: File No. E72422
• BSI approved: No. 8245/8246
• CSA approved: No. CA 101391
APPLICATIONS
• Exchange equipment
• Measurement equipment
• FA/OA equipment
<R>
Data Sheet PN10289EJ02V0DS
2
PS7160-1A,PS7160L-1A
PACKAGE DIMENSIONS (in millimeters)
9.25±0.5
3.5±0.3
4.15±0.3
3.3±0.3
0.5±0.1 2.54
1.34±0.1
0.25 M
0 to 15˚
7.62
6.5±0.5
9.25±0.5
6.5±0.5
0.10
+0.10
–0.05
0.9±0.25
9.60±0.4
3.5±0.3
1.34±0.1
0.25 M 2.54
PS7160-1A
PS7160L-1A
1. LED Anode
2. LED Cathode
3. NC
4. MOS FET Drain
5. MOS FET Source
6. MOS FET Drain
123
654
TOP VIEW
1. LED Anode
2. LED Cathode
3. NC
4. MOS FET Drain
5. MOS FET Source
6. MOS FET Drain
123
654
TOP VIEW
Data Sheet PN10289EJ02V0DS 3
PS7160-1A,PS7160L-1A
MARKING EXAMPLE
No. 1 pin
Mark
PS7160-1A
NL601
Country Assembled
Type Number
Assembly Lot
601
Year Assembled
(Last 1 Digit)
LN
Rank Code
In-house Code
(L: Pb-Free)
Week Assembled
<R>
Data Sheet PN10289EJ02V0DS
4
PS7160-1A,PS7160L-1A
ORDERING INFORMATION
Part Number Order Number Solder Plating
Specification Packing Style Safety Standard
Approval Application Part
Number*1
PS7160-1A PS7160-1A-A Pb-Free Magazine case 50 pcs Standard products PS7160-1A
PS7160L-1A PS7160L-1A-A (UL, BSI, CSA
PS7160L-1A-E3 PS7160L-1A-E3-A Embossed Tape 1 000 pcs/reel approved)
PS7160L-1A-E4 PS7160L-1A-E4-A
*1 For the application of the Safety Standard, following part number should be used.
<R>
Data Sheet PN10289EJ02V0DS 5
PS7160-1A,PS7160L-1A
ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified)
Parameter Symbol Ratings Unit
Diode Forward Current (DC) IF 50 mA
Reverse Voltage VR 5.0 V
Power Dissipation PD 50 mW
Peak Forward Current *1 IFP 1 A
MOS FET Break Down Voltage VL 600 V
Continuous Connection A IL 90 (120) mA
Load Current *2 Connection B 130 (160)
Connection C 200 (210)
Pulse Load Current *3
(AC/DC Connection) ILP 250 mA
Power Dissipation PD 560 mW
Isolation Voltage *4 BV 1 500 Vr.m.s.
Total Power Dissipation PT 610 mW
Operating Ambient Temperature TA −40 to +85 °C
Storage Temperature Tstg −40 to +100 °C
*1 PW = 100
µ
s, Duty Cycle = 1%
*2 Conditions: IF ≥ 2 mA.
Conditions: IF ≥ 5 mA. Load current ( ) value is.
The following types of load connections are available.
Connection A V
L
(AC/DC)
16
25
4
3I
L
L
Connection B
Connection C
16
25
43
I
L
LV
L
(DC)
+
–
16
25
4
3
I
L
I
L
LV
L
(DC)
+
–
16
25
4
3I
L
LV
L
(DC)
+
–
I
L
+ I
L
*3 PW = 100 ms, 1 shot
*4 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output.
Pins 1-3 shorted together, 4-6 shorted together.
Data Sheet PN10289EJ02V0DS
6
PS7160-1A,PS7160L-1A
RECOMMENDED OPERATING CONDITIONS (TA = 25°C)
Parameter Symbol MIN. TYP. MAX. Unit
LED Operating Current IF 2 10 20 mA
LED Off Voltage VF 0 0.5 V
ELECTRICAL CHARACTERISTICS (TA = 25°C)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
Diode Forward Voltage VF IF = 10 mA 1.2 1.4 V
Reverse Current IR VR = 5 V 5.0
µ
A
MOS FET Off-state Leakage
Current ILoff VD = 600 V 0.03 1.0
µ
A
Output Capacitance Cout VD = 0 V, f = 1 MHz 110 pF
Coupled LED On-state Current IFon IL = 90 mA 2.0 mA
On-state Resistance Ron1 IF = 10 mA, IL = 10 mA 42 50 Ω
Ron2 IF = 10 mA, IL = 90 mA, t ≤ 10 ms 33 50
Turn-on Time *1, 2 ton IF = 10 mA, VO = 5 V, RL = 1.5 kΩ, 0.8 1.5 ms
Turn-off Time *1, 2 toff PW ≥ 10 ms 0.06 0.2
Isolation Resistance RI-O VI-O = 1.0 kVDC 109 Ω
Isolation Capacitance CI-O V = 0 V, f = 1 MHz 1.1 pF
*1 Test Circuit for Switching Time
V
L
R
L
I
F
R
in
Pulse Input
Input monitor monitorV
O
t
on
t
off
10 %
90 %
0
V
O
= 5 V
50 %
Output
Input
*2 The turn-on time and turn-off time are specified as input-pulse width ≥ 10 ms.
Be aware that when the device operates with an input-pulse width less than 10 ms, the turn-on time and turn-off
time will increase.
<R>
Data Sheet PN10289EJ02V0DS 7
PS7160-1A,PS7160L-1A
TYPICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified)
Maximum Forward Current IF (mA)
Ambient Temperature TA (˚C)
MAXIMUM FORWARD CURRENT vs.
AMBIENT TEMPERATURE
100
85
7550250–25
20
60
80
100
40
0
IF = 50 mA
30 mA
20 mA
10 mA
5 mA
1 mA
Forward Voltage VF (V)
Ambient Temperature TA (˚C)
FORWARD VOLTAGE vs.
AMBIENT TEMPERATURE
100
7550250–25
1.4
1.6
0.8
1.2
1.0
Maximum Load Current IL (mA)
Ambient Temperature TA (˚C)
MAXIMUM LORD CURRENT vs.
AMBIENT TEMPERATURE
100
85
7550250–25
25
75
100
125
50
0
150
f = 1 MHz
Output Capacitance Cout (pF)
Applied Voltage VD (V)
OUTPUT CAPACITANCE vs.
APPLIED VOLTAGE
120
10080604020
50
150
200
250
100
0
Off-state Leakage Current ILoff (A)
Applied Voltage VD (V)
OFF-STATE LEAKAGE CURRENT vs.
APPLIED VOLTAGE LORD CURRENT vs. LORD VOLTAGE
Load Current IL (mA)
Load Voltage VL (V)
IF = 10 mA
–2.0 2.0–4.0 4.00
50
150
100
–50
–150
–100
6005003001000 200 400
10–3
10–4
10–5
10–6
10–7
10–8
10–9
TA = 85 ˚C
25 ˚C
Remark The graphs indicate nominal characteristics.
Data Sheet PN10289EJ02V0DS
8
PS7160-1A,PS7160L-1A
Turn-on Time ton (ms)
Forward Current IF (mA)
TURN-ON TIME vs. FORWARD CURRENT
40
302010
2.0
4.0
6.0
8.0
0
Number (pcs)
Turn-on Time ton (ms)
TURN-ON TIME DISTRIBUTION
0.7 0.90.6 0.8 1.0
0
5
10
15
20
25
30 n = 50 pcs,
IF = 10 mA,
VO = 5 V
Turn-off Time toff (ms)
Forward Current IF (mA)
TURN-OFF TIME vs. FORWARD CURRENT
40302010
0
0.2
0.3
0.5
0.4
0.1
V
O = 5 V
Number (pcs)
Turn-off Time toff (ms)
TURN-OFF TIME DISTRIBUTION
0.04 0.08
0
5
10
15
20
25
30 n = 50 pcs,
IF = 10 mA,
VO = 5 V
VO = 5 V
Normalized to 1.0
at TA = 25 ˚C,
IF = 10 mA,
IL = 10 mA
Normalized On-state Resistance Ron
Ambient Temperature TA (˚C)
NORMALIZED ON-STATE RESISTANCE
vs. AMBIENT TEMPERATURE
100
7550250–25
0.5
1.5
2.5
3.0
1.0
0.0
2.0
n = 50 pcs,
IF = 10 mA,
IL = 10 mA
ON-STATE RESISTANCE DISTRIBUTION
Number (pcs)
On-state Resistance Ron (Ω)
434241
5
15
20
30
10
0
25
Remark The graphs indicate nominal characteristics.
Data Sheet PN10289EJ02V0DS 9
PS7160-1A,PS7160L-1A
Normalized Turn-on Time ton
Ambient Temperature TA (˚C)
NORMALIZED TURN-ON TIME vs.
AMBIENT TEMPERATURE
100
0–25 25 50 75
2.5
3.0
0.0
2.0
1.5
1.0
0.5
Normalized to 1.0
at TA = 25 ˚C,
IF = 10 mA,
VO = 5 V
Normalized Turn-off Time toff
Ambient Temperature TA (˚C)
NORMALIZED TURN-OFF TIME vs.
AMBIENT TEMPERATURE
100
0–25 25 50 75
2.5
3.0
0.0
2.0
1.5
1.0
0.5
Normalized to 1.0
at TA = 25 ˚C,
IF = 10 mA,
VO = 5 V
Remark The graphs indicate nominal characteristics.
Data Sheet PN10289EJ02V0DS
10
PS7160-1A,PS7160L-1A
TAPING SPECIFICATIONS (in millimeters)
Tape Direction
PS7160L-1A-E3 PS7160L-1A-E4
Outline and Dimensions (Tape)
1.55±0.1
2.0±0.1
4.0±0.1
1.75±0.1
4.5 MAX.
10.4±0.1
12.0±0.1
1.5
+0.1
–0
7.5±0.1
10.3±0.1
16.0±0.3
4.0±0.1
0.3
Outline and Dimensions (Reel)
Packing: 1 000 pcs/reel
330±2.0
100±1.0
2.0±0.5
13.0±0.2
R 1.0 21.0±0.8
2.0±0.5
15.9 to 19.4
Outer edge of
flange
21.5±1.0
17.5±1.0
Data Sheet PN10289EJ02V0DS 11
PS7160-1A,PS7160L-1A
RECOMMENDED SOLDERING CONDITIONS
(1) Infrared reflow soldering
• Peak reflow temperature 260°C or below (package surface temperature)
• Time of peak reflow temperature 10 seconds or less
• Time of temperature higher than 220°C 60 seconds or less
• Time to preheat temperature from 120 to 180°C 120±30 s
• Number of reflows Three
• Flux Rosin flux containing small amount of chlorine (The flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
220˚C
Package Surface Temperature T (˚C)
Time (s)
(heating)
to 10 s
to 60 s
260˚C MAX.
Recommended Temperature Profile of Infrared Reflow
120±30 s
(preheating)
180˚C
120˚C
(2) Wave soldering
• Temperature 260°C or below (molten solder temperature)
• Time 10 seconds or less
• Preheating conditions 120°C or below (package surface temperature)
• Number of times One
• Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine
content of 0.2 Wt% is recommended.)
(3) Soldering by soldering iron
• Peak temperature (lead part temperature) 350°C or below
• Time (each pins) 3 seconds or less
• Flux Rosin flux containing small amount of chlorine (T he flux with a
maximum chlorine content of 0.2 Wt% is recommended.)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead.
(b) Please be sure that the temperature of the package would not be heated over 100°C.
(4) Cautions
• Fluxes
Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent.
<R>
Data Sheet PN10289EJ02V0DS
12
PS7160-1A,PS7160L-1A
USAGE CAUTIONS
1. Protect against static electricity when handling.
2. Avoid storage at a high temperature and high humidity.
<R>
Data Sheet PN10289EJ02V0DS 13
PS7160-1A,PS7160L-1A
The information in this document is current as of July, 2006. The information is subject to change
without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or
data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all
products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customer-
designated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
•
•
•
•
•
•
M8E 02. 11-1
(1)
(2)
"NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
"NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
"Standard":
"Special":
"Specific":
0604
NEC Compound Semiconductor Devices Hong Kong Limited
E-mail: contact@ncsd-hk.necel.com
Hong Kong Head Office TEL: +852-3107-7303 FAX: +852-3107-7309
Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859
Korea Branch Office TEL: +82-2-558-2120 FAX: +82-2-558-5209
NEC Electronics (Europe) GmbH http://www.eu.necel.com/
TEL: +49-211-6503-0 FAX: +49-211-6503-1327
California Eastern Laboratories, Inc. http://www.cel.com/
TEL: +1-408-988-3500 FAX: +1-408-988-0279
Compound Semiconductor Devices Division
NEC Electronics Corporation
URL: http://www.ncsd.necel.com/
For further information, please contact
PS7160-1A,PS7160L-1A
Caution GaAs Products This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe
the following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
