TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 1 of 8 -
www.qorvo.com
®
14 Pin 7 x 7 mm Leadless SMT Package
Product Features
• 2.3 – 2.4 GHz Frequency Range
• Fully integrated, 3-Stage Power Amplifier
• Internally Matched 50 Ω Input/Output
• −50 dBc ACLR at Pavg = +24 dBm
• 36.7 dB Gain
• 14% PAE at +24 dBm
• 204 mA Quiescent Current
• On-chip Control Bias and Temp. Comp Circuit
• RoHS compliant
• Covers Band 30, 40
General Description
The TQP9224 is a high-linearity three-stage power
amplifier in a low-cost surface-mount package with on-chip
bias control and temperature control circuits, suitable for
small cell or enterprise Femto cell base station applications.
The TQP9224 provides 36.7 dB high gain and −50 dBc
ACLR at +24 dBm linear power using a 20 MHz LTE signal
over the 2.3 – 2.4 GHz frequency range covering 3GPP
Bands 30, 40.
The TQP9224 integrates three high performance amplifier
stages to allow for a compact system design and requires
very few external components for operation. The amplifier
is bias adjustable allowing the amplifier’s power
consumption to be optimized for specific performance
requirements. The TQP9224 is available in a lead-
free/RoHS-compliant 7 x 7 mm surface mount package.
Ordering Information
Part No.
Description
TQP9224TR13
2,500 pieces on a 13” reel (standard)
TQP9224PCB401
2.3−2.4 GHz Evaluation Board
Functional Block Diagram
Top View
Applications
• Small Cell / Picocell
• Enterprise Femtocell
• Customer Premises Equipment (CPE)
• Data Cards and Terminals
• Distributed Antenna Systems (DAS)
• Booster Amps, Repeaters
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 2 of 8 -
www.qorvo.com
®
Recommended Operating Conditions
Parameter
Min
Typ
Max
Units
VCC1, Vcc2
+3.6
+4.5
+5.25
V
Vref
+2.75
+2.85
+2.95
V
TCASE
−40
+85
°C
Tj at TCASE max
+156
°C
Electrical specifications are measured at specified test conditions.
Specifications are not guaranteed over all recommended operating
conditions.
Absolute Maximum Ratings
Parameter
Rating
Storage Temperature
−55 to +150 °C
RF Input Power, CW, 50Ω, T=+25 °C
+9 dBm
Supply Voltage (VCC)
6 V
VREF
+3.5 V
Exceeding any one or a combination of the Absolute Maximum Rating
conditions may cause permanent damage to the device. Extended
application of Absolute Maximum Rating conditions to the device may
reduce device reliability.
Electrical Specifications
Parameter
Conditions(1)
Min
Typ
Max
Units
Frequency Range
2300
2400
MHz
Test Frequency
2350
MHz
Gain
34
36.7
40
dB
Input Return Loss
16
dB
Output Return Loss
8
dB
Output P1dB
+33.6
dBm
ACLR
POUT = +24 dBm, 20 MHz LTE E-TM1.1, 9.5 dB PAR
−50
-45
dBc
Power Added Efficiency
POUT = +24 dBm, 20 MHz LTE E-TM1.1, 9.5 dB PAR
13
14
%
Spurious Output Level
POUT = +24 dBm, 10:1 VSWR
<60
dBc
VSWR survivability
No permanent degradation or failure
10:1
-
Quiescent Current, ICQ
VCC1 + VCC2
160
204
250
mA
Reference Current , Iref
Temp = −40°C to +85°C, VREF = +2.85V
8.7
mA
Leakage Current
VCC = +4.5 V, VREF = 0 V
1.5
8
µA
Operational Current, ICC
POUT = +24 dBm
390
430
mA
Switching Speed
0% Vref to 90% RF Rise time
1.7
2.5
µs
100% Vref to 10% RF Fall time
0.87
1
µs
Harmonics
2F0 at +24dBm, CW signal
-40
-35
dBc
3F0 at +24dBm, CW signal
-54
-49
dBc
4F0 at +24dBm, CW signal
-61
-56
dBc
Thermal Resistance, θjc
Module (junction to case)
35.4
°C/W
Notes:
1. Test conditions unless otherwise noted: VCC1 = Vcc2 = +4.5 V, VREF = +2.85V, Temp = +25 °C, 50 Ω system.
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 3 of 8 -
www.qorvo.com
®
Evaluation Board (TQP9224−PCB)
Bill of Material – TQP9224−PCB
Reference Des.
Value
Description
Manuf.
Part Number
n/a
n/a
Printed Circuit Board
U1
n/a
High Linearity 0.25 W Power Amplifier
Qorvo
TQP9224
R1
0 Ω
Resistor, Chip, 0603, 5%
various
C1
0.01 uF
Capacitor, Chip, 0603, 5%
various
C11
100 pF
Capacitor, Chip, 0603, 5%
various
C3, C9
0.1 uF
Capacitor, Chip, 0603, 5%
various
C5, C14
10 uF
Capacitor , Chip, 6032, 10%, Tantalum
various
C6, C10
1000 pF
Capacitor , Chip, 0603, NPO/COG, 5%
various
7
6
1
10
8
9
11
12
13
14
2
3
4
5Match
Match
Biasing Circuit
C5
10uF (6032)
R1
0
J3
Vcc1
C9
1.0uF
C6
1000pF
J5
Vpd
C1
0.01uF
C11
100pF
J1
RF
Input
J2
RF
Output
R2
DNP
J6
Vdet
C13
DNP
C12
DNP
C3
1.0uF
C10
1000pF
C14
10uF (6032)
J4
Vcc2
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 4 of 8 -
www.qorvo.com
®
Performance Plots
Test conditions unless otherwise noted: VCC1 = VCC2 = +4.5V, VREF = +2.85 V, ICQ = 204mA, IREF = 8.7mA, Temp.= +25 °C
32
34
36
38
40
42
2300 2320 2340 2360 2380 2400
Gain (dB)
Frequncy (MHz)
Gain vs Frequency vs Temperature
+85°C
+25°C
−40°C
-20
-15
-10
-5
0
2300 2320 2340 2360 2380 2400
|S11| (dB)
Frequency (MHz)
Input Return Loss vs. Frequency
Temp.=+25°C
-15
-10
-5
0
2300 2320 2340 2360 2380 2400
|S22| (dB)
Frequency (MHz)
Output Return Loss vs. Frequency
Temp.=+25°C
-60
-55
-50
-45
-40
-35
-30
16 17 18 19 20 21 22 23 24 25 26
ACLR (dBc)
Pout (dBm)
ACLR vs Pout vs Frequency
2.30GHz_L
2.30GHz_U
2.35GHz_L
2.35GHz_U
2.40GHz_L
2.40GHz_U
Temp.=+25°C
LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz
PAR 9.5 dB no clipping
-60
-55
-50
-45
-40
-35
-30
16 17 18 19 20 21 22 23 24 25 26
ACLR (dBc)
Pout (dBm)
ACLR vs Pout vs Temperature
-40C_L
-40C_U
+25C_L
+25C_U
+85C_L
+85C_U
Freq = 2350MHz
LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz
PAR 9.5 dB no clipping
30
31
32
33
34
35
2300 2320 2340 2360 2380 2400
P1dB (dBm)
Frequency (MHz)
P1dB vs Frequency
+85°C
+25°C
−40°C
0
5
10
15
20
16 17 18 19 20 21 22 23 24 25 26
PAE (%)
Pout (dBm)
Efficiency vs Pout vs Frequency
2.30GHz
2.35GHz
2.40GHz
Temp.=+25°C
LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz
PAR 9.5 dB no clipping
0
5
10
15
20
16 17 18 19 20 21 22 23 24 25 26
PAE (%)
Pout (dBm)
Efficiency vs Pout vs Temperature
-40C
+25C
+85C
Freq = 2350MHz
LTE 1 CH 20 MHz, Adj ch IBW 18.02 MHz
PAR 9.5 dB no clipping
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 5 of 8 -
www.qorvo.com
®
Pin Configuration and Description
Top View
Pad No.
Label
Description
1
VREF
Sets the bias current for the amplifiers. It can also be used to power down the device.
2, 3, 6, 8, 9, 10,
13, 14
GND
RF and DC ground.
4
VCC1
Voltage supply for the active bias circuitry.
5
RFin
RF input pin. The DC is internally blocked at this pin.
7
NC
No internal connection.
11
VCC2
DC voltage supply connection for AMP1, 2, 3.
12
RFout
RF output pin. The DC is internally blocked at this pin.
Backside Paddle
RF/DC GND
RF/DC ground. See PCB Mounting Pattern for suggested footprint.
Evaluation Board PCB Information
Qorvo PCB 1126637 Material and Stack-up
50 ohm line dimensions: width = .028”
spacing = .028”.
1 oz. Cu bottom layer
Nelco N-4000-13
Core
Nelco N-4000-13 1 oz. Cu top layer
1 oz. Cu inner layer
1 oz. Cu inner layer
0.062" ± 0.006"
Finished Board
Thickness
0.014"
0.014"
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 6 of 8 -
www.qorvo.com
®
Package Marking and Dimensions
Marking: Part Number – TQP9224
Trace Code
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Dimension and tolerance formats conform to ASME Y14.4M-1994.
3. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012.
1
2
3
4
5
6
8
9
7
10
11
13
12
14
PIN 1 Location
A
A
S
S
A
A
A
A
A
A A
A
A
A
A
A
A
BOTTOM
VIEW BOTTOM PINS
VIEW
A3HD000000D000000 00:00 TOP
SIDE
/
TriQuint
Reach Further - Reach faster
07.00mm X 07.00mm, 4 LAYER
1
2
3
4
5
6
8
9
7
10
11
13
12
14
PIN 1 Location
A
A
S
S
A
A
A
A
A
A A
A
A
A
A
A
A
BOTTOM
VIEW BOTTOM PINS
VIEW
A3HD000000D000000 00:00 TOP
SIDE
/
TriQuint
Reach Further - Reach faster
07.00mm X 07.00mm, 4 LAYER
TQP9224
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 7 of 8 -
www.qorvo.com
®
PCB Mounting Pattern
Notes:
1. All dimensions are in millimeters. Angles are in degrees.
2. Use 1 oz. copper minimum for top and bottom layer metal.
3. Vias are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. We recommend a 0.35mm
(#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10”).
4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance.
0.175
PIN 1 Location
A
A
S
S
A
A
A
A
A
A A
A
A
A
A
A
A
PIN 1 Location
A
A
S
S
A
A
A
A
A
A A
A
A
A
A
A
A
RECOMMENDED
LAND PATTERN RECOMMENDED
LAND PATTERN MASK
A3HD000000D000000 00:00 RLP
RLPmsk
TriQuint
Reach Further - Reach faster
07.00mm X 07.00mm, 4 LAYER
TQP9224
High Linearity 0.25 W Small Cell PA
Data Sheet March 1, 2018 | Subject to change without notice
- 8 of 8 -
www.qorvo.com
®
Handling Precautions
Parameter
Rating
Standard
Caution!
ESD-Sensitive Device
ESD – Human Body Model (HBM)
Class 2
ESDA / JEDEC JS-001-2012
ESD – Charged Device Model (CDM)
Class C3
JEDEC JESD22-C101F
MSL – Moisture Sensitivity Level
Level 3
IPC/JEDEC J-STD-020
Solderability
Compatible with both lead-free (260°C max. reflow temp.) and tin/lead (245°C max. reflow temp.) soldering processes.
Solder profiles available upon request.
Contact plating: Electrolytic plated Au over Ni
RoHS Compliance
This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment). This product also has the following attributes:
• Product uses RoHS Exemption 7c-I to meet RoHS Compliance requirements
• Halogen Free (Chlorine, Bromine)
• Antimony Free
• TBBP-A (C15H12Br402) Free
• PFOS Free
• SVHC Free
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations:
Tel: 1-844-890-8163
Web: www.qorvo.com
Email: customer.support@qorvo.com
For technical questions and application information: Email: appsupport@qorvo.com
Important Notice
The information contained herein is believed to be reliable; however, Qorvo makes no warranties regarding the information contained
herein and assumes no responsibility or liability whatsoever for the use of the information contained herein. All information contained
herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for
Qorvo products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any
patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by
such information. THIS INFORMATION DOES NOT CONSTITUTE A WARRANTY WITH RESPECT TO THE PRODUCTS DESCRIBED
HEREIN, AND QORVO HEREBY DISCLAIMS ANY AND ALL WARRANTIES WITH RESPECT TO SUCH PRODUCTS WHETHER
EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Without limiting the generality of the foregoing, Qorvo products are not warranted or authorized for use as critical components in medical,
life-saving, or life-sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal
injury or death.
Copyright 2018 © Qorvo, Inc. | Qorvo is a registered trademark of Qorvo, Inc.
