AN34001A - Panasonic - Product.Network

DATA SHEET

Part No.

Package Code No.

Publication date: May 2007 SDH00016AEB

AN34001A

HZIP016-P-0665F

AN34001A

SDH00016AEB

Contents

Overview … …………………………………………….……………………………………………………… 3

Features ……………………………………………….……………………………………………………… 3

Applications …………………………………………….……………………………………………………… 3

Package ……………………………………………….………………………………………………………… 3

Type ………………………………………………….…………………………………………………………. 3

Application Circuit Example …………………………………………………………………………………… 4

Block Diagram ………………………………………….……………………………………………………… 5

Pin Descriptions……………………………………….………………………………………………………… 5

Absolute Maximum Ratings…………………………….……………………………………………………… 6

AN34001A

SDH00016AEB

AN34001A

Nine-Output Linear Voltage Regulator

Overview

AN34001A is a nine-output power supply IC, consisting of five linear regulator (one adjustable) and four voltage followers. Seven of

the outputs are controlled by three control switches.

Features

yThermal protection circuit.

yShort circuit protection circuit

yOver voltage protection circuit

yOperating supply voltage range: 6.6 V to 18.0 V (13.2 V typical)

yHigh maximum operating voltage: 26 V

Application

Voltage supply for car audio system

Package

16 pin plastic zigzag inline package with heat sink (ZIP type)

Type

Silicon monolithic bipolar IC

AN34001A

SDH00016AEB

Application Circuit Example

ACC

MODE1

VCC

VCC VCC

VCC

VCCVCC

VCC

147

1514 13

Reference Voltage

EXT

Out

8910 11 2

16 12

* Peak Current Protection, Over Voltage Protection

* Thermal Shutdown Protection (except for VDD, DSP and COMP

output)

Outputs

ILM

10 V

SW AUDIO

9 V

VDD

5 V

GND CD

8 V

DSP

3.3 V

EXT VCC ANT MODE2 COMP

Pre-

Drive

Pre-

Drive

Pre-

Drive

ANT

Out

Pre-

Drive

Pre-

Drive

22 μF

22 μF22 μF

47 μF22 μF

22 μF22 μF22 μF22 μF22 μF

AN34001A

SDH00016AEB

Block Diagram

When Mode 1 pin is “M” and “H”, ILM output is 10 V (IO = 300 mA)OutputILM15

A pin to adjust the ILM (illumination) output. InputILM AJ14

When Mode 1 pin is “M” and “H”, SW output is VDD (IO = 100 mA)OutputSW1

When ACC input pin is “H” COMP output is VDD (IO = 100 mA)OutputCOMP2

“L”: COMP Ouptut OFF and “H”: COMP Output ONInputACC3

5 V output voltage for a microcontroller (IO = 100 mA)OutputVDD4

Not connected to the IC die—N.C.5

Three-input “L”, “M”, and “H” control pinInputMODE16

When Mode 1 is “H” CD output is 8 V (IO= 1 200 mA)OutputCD7

DescriptionType

name

Pin No.

Connected to the IC substrateGroundGND16

When Mode 1 pin is “M” and “H”, AUDIO output is 9 V (IO = 500 mA)OutputAUDIO13

3.3 V output voltage for DSP IC (IO = 150 mA)OutputDSP12

“L”: ANT Output OFF and “H”: ANT Output ONInputMODE211

When Mode 2 pin is “H” ANT output is VCC –1 V (I

O = 300 mA)OutputANT10

Connected to car BACKUP power supplyPower SupplyVCC9

When Mode 1 pin is “M” and “H”, SW output is VCC –1V (I

O = 300 mA)OutputEXT8

Pin Description

ACC

MODE1

VCC

VCC VCC

VCC

VCCVCC

VCC

147

1514 13

Reference Voltage

EXT

Out

8910 11 2

16 12

* Peak Current Protection, Over Voltage Protection

* Thermal Shutdown Protection (except for VDD, DSP and COMP

output)

Outputs

ILM

10 V

SW AUDIO

9 V

VDD

5 V

GND CD

8 V

DSP

3.3 V

EXT VCC ANT MODE2 COMP

Pre-

Drive

Pre-

Drive

Pre-

Drive

ANT

Out

Pre-

Drive

Pre-

Drive

AN34001A

SDH00016AEB

Absolute Maximum Ratings

Operating power supply range

°C−55 to +150

Tstg

Storage temperature5

NoteUnitRatingSymbolParameter

No.

*2A5.2ICC

Supply current2

°C−30 to +85

Topr

Operating ambient temperature4

*3W16.25PD

Power dissipation3

*1V26.0VCC

Supply voltage1

V6.6 to 18.0VCC

Operating supply voltage range

NoteUnitRangeSymbolParameter

Note) *5: ILM output is not regulated for VCC below 10.5V

*6: AUDIO and CD output might not be functioning well for VCC below 10V

Notes) *1 : The values under the condition not exceeding the above absolute maximum ratings and the power dissipation.

*2 : Over current limiting circuit built-in.

*3 : The power dissipation shown is the value at Ta=85°C with 4°C / Watt heat sink.

When using this IC, refer to the PD-Tadiagram of the package standard and use under the condition not exceeding the allowable value.

*4 : Except for the power dissipation, operating ambient temperature, and storage temperature, all ratings are for Ta=25°C.

Request for your special attention and precautions in using the technical information and

semiconductors described in this book

(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and

regulations of the exporting country, especially, those with regard to security export control, must be observed.

(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples

of the products, and no license is granted under any intellectual property right or other right owned by our company or any other

company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other

company which may arise as a result of the use of technical information described in this book.

(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office

equipment, communications equipment, measuring instruments and household appliances).

Consult our sales staff in advance for information on the following applications:

– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support

systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-

ucts may directly jeopardize life or harm the human body.

– Any applications other than the standard applications intended.

(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-

provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product

Standards in advance to make sure that the latest specifications satisfy your requirements.

(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions

(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute

maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any

defect which may arise later in your equipment.

 Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure

mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire

or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.

(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,

thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which

damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.

(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita

Electric Industrial Co., Ltd.