G4IDC5D - OPTO 22 - Product.Network

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

© 2003–2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

PAGE 1

DATA SHEET

Form 0253-180917

G4 DIGITAL DC INPUT MODULES

Features

4000 volts transient optical isolation

Built-in LED status indicator

Small footprint design, reducing mounting space by

approximately 50 percent

Built-in filtering for transient suppression and noise rejection

Operating temperature: -30 °C to 70 °C

UL recognized, CSA certified, CE approved

Passes NEMA Showering Arc Test (ICS 2-230)

Meets IEEE Surge Withstand Specification (IEEE-472)

DESCRIPTION

Opto 22’s G4 DC input modules are used to detect on/off DC voltage

levels. Each module provides up to 4000 volts (transient) of optical

isolation between field inputs and the logic output of the circuit.

All DC input modules except the G4IDC5K and G4IDC5D are designed

with filtering on the input and a hysteresis amplifier, providing high

noise rejection and transient-free, “clean” switching. The G4IDC5K is a

fast-switching module used to detect signals produced by

photoelectric switches and TTL devices. The low-cost G4IDC5D is

used for data acquisition.

The G4IDC5MA is a special module featuring a

manual-on/manual-off/automatic switch, ideal for diagnostic testing

of control applications.

The G4IDC5-SW and G4IDC5-SWNC modules supply power to an

external dry contact switch and sense switch closure (SW) or opening

(SWNC).

Typical applications for DC input modules include sensing the

presence or absence of voltage and sensing contact closure from

sources such as proximity switches, limit switches, selector switches,

push buttons, photoelectric switches, and TTL-compatible devices.

Compatible with Raspberry Pi

The following G4 digital DC input modules can be used with the

Digital I/O Carrier Board for Raspberry Pi® (part number OPTO-P1-40P)

to monitor and control industrial devices with your Raspberry Pi:

•G4IDC5

•G4IDC5D

•G4IDC5G

•G4IDC5MA

Part Numbers

Part Description

G4IDC5* G4 DC Input 10–32 VDC, 5 VDC Logic

G4IDC5B G4 DC Input 4–16 VDC, 5 VDC Logic High

Speed

G4IDC5D* G4 DC Input 2.5–28 VDC, 5 VDC Logic

G4IDC5G* G4 DC Input 35–60 VDC, 5 VDC Logic

G4IDC5K G4 DC Input 2.5–16 VDC, 5 VDC Logic Very

High Speed

G4IDC5MA* G4 DC Input 10–32 VDC, 5 VDC Logic With

Manual/Auto Switch

G4IDC5-SW G4 Switch Status Input, Self-powered, Nor-

mally Open

G4IDC5-SWNC G4 Switch Status Input, Self-powered, Nor-

mally Closed

G4IDC15 G4 DC Input 10–32 VDC, 15 VDC Logic

G4IDC24 G4 DC Input 10–32 VDC, 24 VDC Logic

* Compatible with Raspberry Pi

Opto 22 G4 digital input modules include the

G4IDC5B high-speed module and the G4IDC5MA

module with manual-on/manual-off/automatic

switch for diagnostic testing.

Raspberry Pi® is a trademark of the Raspberry Pi Foundation.

PAGE 2

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

DATA SHEET

Form 0253-180917

SPECIFICATIONS

G4IDC5-SW and G4IDC5-SWNC modules

See page 4 for specifications and other information for the

G4IDC5-SW and G4IDC5-SWNC self-powered modules.

Units G4IDC5* G4IDC5B G4IDC5D* G4IDC5G*

Input voltage range VDC

VAC

10–32

12–32

4–16

2.5–28

—

35–60

Key feature — Higher speed High speed —

Input current at maximum line mA 25 45 30 6

Isolation, input-to-output (transient):

1 ms

1 minute

4000

1500

4000

1500

4000

1500

4000

1500

Turn-on time ms 5 0.05 1 10

Turn-off time ms 5 0.1 1.5 10

Input allowed for off-state mA, V 1, 3 0.7, 1 0.2, 1 0.7, 7

Nominal output supply voltage VDC 5555

Output supply voltage range VDC 4.5–6 4.5–6 4.5–6 4.5–6

Output supply current at

nominal logic voltage mA 12 12 12 12

Input resistance (R1 in schematic) ohms 1.5 K 300 900 10 K

Control resistance (Rc in schematic) ohms 220 220 470 220

Output voltage drop V @ 50 mA 0.4 0.4 0.4 0.4

Output current (sinking) mA 50 50 50 50

Output leakage with no input microamps @

30 VDC 100 100 10 100

Transistor V breakdown 30 30 30 30

Temperature:

Operating

Storage

–30 to +70

–30 to +85

–30 to +70

–30 to +85

–30 to +70

–30 to +85

–30 to +70

–30 to +85

* Compatible with Raspberry Pi

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

PAGE 3

DATA SHEET

Form 0253-180917

SPECIFICATIONS (CONT.)

Units G4IDC5K G4IDC5MA* G4IDC15** G4IDC24**

Input voltage range VDC

VAC

2.5–16

—

10–32

12–32

10–32

12–32

10–32

12–32

Key feature Highest

speed

Diagnostic

switch ——

Input current at maximum line mA 30 25 25 25

Isolation, input-to-output (transient):

1 ms

1 minute

4000

1500

4000

1500

4000

1500

4000

1500

Turn-on time ms 0.025*** 5 5 5

Turn-off time ms 0.025*** 5 5 5

Input allowed for off-state mA, V 0.2, 1 1, 3 1, 3 1,3

Nominal output supply voltage VDC 5 5 15 24

Output supply voltage range VDC 4.5–6 4.5–6 12–18 20–30

Output supply current at

nominal logic voltage mA 12 12 15 18

Input resistance (R1 in schematic) ohms 500 1.5 K 1.5 K 1.5 K

Control resistance (Rc in schematic) ohms 220 220 1 K 2.2 K

Output voltage drop V @ 50 mA 0.4 0.4 0.4 0.4

Output current (sinking) mA 50 50 50 50

Output leakage with no input microamps @

30 VDC 100 100 100 100

Transistor V breakdown 30 30 30 30

Temperature:

Operating

Storage

–30 to +70

–30 to +85

–30 to +70

–30 to +85

–30 to +70

–30 to +85

–30 to +70

–30 to +85

* Compatible with Raspberry Pi

** Not for use with Opto 22 brains

*** At 5Vp-p square wave input, 50% duty cycle

PAGE 4

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

DATA SHEET

Form 0253-180917

G4IDC5-SW AND G4IDC5-SWNC MODULES

Description

Each G4IDC5-SW and G4IDC5-SWNC module provides one isolated

channel of contact status input. Each module supplies 13 volts of

power to an external dry contact switch. The G4IDC5-SW senses

switch closure; the G4IDC5-SWNC senses switch opening. Each

user-supplied switch is connected with two wires. Because these

modules include power for the switch, they are particularly

cost-effective when labor costs for wiring external power are high.

Typical switches for use with these modules are switched status

sensors (level sensors, pressure indicators, etc.), magnetic reed

switches (used on doors or windows for burglar alarms), snap-action

micro switches, the auxiliary switches on motor starters, and most

relay contacts.

CAUTION: G4IDC5-SW and G4IDC5-SWNC inputs are not intended to

be used with contacts that are connected to any external

user-supplied voltage or currents.

Specifications

Field Side Ratings

Open Circuit Voltage (Switch Open) 11 VDC min., 13 VDC typical, 15 VDC max.

Short Circuit Current (Switch Closed) 6 milliamps nominal

Minimum Off Resistance 20 K ohms

Maximum Allowable On Resistance

(Wire + Contact Resistance) 500 ohms

Logic Side Ratings

Logic Output Voltage for G4IDC5-SW

(normally open)

<0.5 V max. (switch closed; LED on) @ 2 mA sinking

2.7 V min. (switch open; LED off) @ 0.4 mA sourcing

Logic Output Voltage for G4IDC5-SWNC

(normally closed)

<0.5 V max. (switch open; LED on) @ 2 mA sinking

2.7 V min. (switch closed; LED off) @ 0.4 mA sourcing

Maximum Operating Common Mode

Voltage (Field Term to Logic Connector) 250 V

Power Requirements: 5 VDC (±0.25) @ 25 mA nom.

Module Ratings

Number of Channels Per Module 1

Turn-on Time 8 msec typical

Turn-off Time 8 msec typical

Input-to-output Isolation (transient) 4000 V AC/DC

Temperature 0 °C to 70 °C, operating

–30 °C to 85 °C, storage

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

PAGE 5

DATA SHEET

Form 0253-180917

Schematic

Dimensions

PAGE 6

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • sales@opto22.com

DATA SHEET

Form 0253-180917

Schematics

OPTO 22 • www.opto22.com SALES • sales@opto22.com SUPPORT • support@opto22.com

43044 Business Park Dr. Temecula, CA 92590-3614 800-321-6786 • 1-951-695-3000 800-835-6786 • 1-951-695-3080

© 2006–2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

More about Opto 22

Form 1335-180323

PRODUCTS

Opto 22 develops and manufactures reliable, easy-to-use, open

standards-based hardware and software products.

Industrial automation, process control, building automation, industrial

refrigeration, remote monitoring, data acquisition, and industrial

internet of things (IIoT) applications worldwide all rely on Opto 22.

groov EPIC® System

Opto 22’s groov Edge Programmable Industrial Controller (EPIC)

system is the culmination of over 40 years of experience in designing

products for the automation industry.

groov EPIC gives you an industrially hardened system with

guaranteed-for-life I/O, a flexible Linux®-based controller with

gateway functions, and software for your IIoT application or any

application.

groov EPIC I/O

I/O provides the local connection to

sensors and equipment. groov I/O

offers up to 24 channels on each I/O

module, with a spring-clamp terminal

strip, integrated wireway, and swing-

away cover.

Opto 22 I/O is so reliable, we can afford

to guarantee it for life. groov I/O is hot

swappable, UL Hazardous Locations

approved, and ATEX compliant.

groov EPIC Controller

The heart of the system is the groov

EPIC controller. It handles a wide range of digital, analog, and serial

functions for data collection, remote monitoring, process control, and

discrete and hybrid manufacturing.

In addition, the EPIC provides secure data communications among

physical assets, control systems, software applications, online services,

and more, both on premises and in the cloud.

Configuring and troubleshooting I/O and networking is easier with

the EPIC’s integrated high-resolution touchscreen. Authorized users

can see your groov View HMI locally on the touchscreen or on a

monitor connected via the HDMI or USB ports.

groov EPIC Software

Software includes:

•Flowchart-based PAC Control for control programming, or build

your own custom application with optional secure shell access

•groov View for building and viewing your own device-

independent HMI

•Node-RED for creating simple logic flows from pre-built nodes

•Ignition Edge® from Inductive Automation®, with OPC-UA drivers

to Allen-Bradley®, Siemens®, and other control systems, and

MQTT/Sparkplug communications for efficient IIoT data transfer

groov Edge Appliance

Visualization, data handling, and connectivity in a

compact, industrial box: that’s the groov Edge

Appliance. Included are:

•groov View for building and viewing operator

interfaces on PCs and mobile

•Node-RED for building simple logic flows

•Ignition Edge® from Inductive Automation®,

for OPC-UA drivers and MQTT/Sparkplug IIoT communications

Older products

From solid state relays (our first products) to world-famous G4 and

SNAP I/O, to SNAP PAC controllers, Opto 22 products last a long time.

You can count on us to give you the reliability and service you expect.

QUALITY

Founded in 1974, Opto 22 has established

a worldwide reputation for high-quality

products. All are made in the U.S.A. at our

manufacturing facility in Temecula,

California.

Because we test each product twice

before it leaves our factory rather than

testing a sample of each batch, we can

guarantee most solid-state relays and

optically isolated I/O modules for life.

FREE PRODUCT SUPPORT

Opto 22’s California-based Product Support Group offers free,

comprehensive technical support for Opto 22 products from

engineers with decades of training and experience. Support is

available in English and Spanish by phone or email, Monday–Friday,

7 a.m. to 5 p.m. PST.

Support is always available on our website, including how-to videos,

user’s guides, the Opto 22 KnowledgeBase, troubleshooting tips, and

OptoForums. In addition, free hands-on training is available at our

Temecula, California headquarters, and you can register online.

PURCHASING OPTO 22 PRODUCTS

Opto 22 products are sold directly and through a worldwide network

of distributors, partners, and system integrators. For more information,

contact Opto 22 headquarters at 800-321-6786 (toll-free in the U.S.

and Canada) or +1-951-695-3000, or visit our website at