W25Q20EW 1.8V 2M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS, DUAL AND QUAD SPI -1- Publication Release Date: July 28, 2015 -Revision D W25Q20EW Table of Contents 1. 2. 4. 5. 6. 7. GENERAL DESCRIPTION ......................................................................................................... 5 FEATURES ................................................................................................................................. 5 PACKAGE TYPES AND PIN CONFIGURATIONS..................................................................... 6 4.1 Pin Configuration SOIC 150-mil and VSOP 150-mil....................................................... 6 4.2 PAD Configuration USON 2x3-mm................................................................................. 6 4.3 Pin Description SOIC/ VSOP 150-mil, USON 2x3-mm .................................................. 6 4.4 Ball Configuration WLCSP.............................................................................................. 7 4.5 Ball Description WLCSP ................................................................................................. 7 PIN DESCRIPTIONS .................................................................................................................. 8 5.1 Chip Select (/CS) ............................................................................................................ 8 5.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)............................... 8 5.3 Write Protect (/WP) ......................................................................................................... 8 5.4 HOLD (/HOLD)................................................................................................................ 8 5.5 Serial Clock (CLK) .......................................................................................................... 8 BLOCK DIAGRAM ...................................................................................................................... 9 FUNCTIONAL DESCRIPTION.................................................................................................. 10 7.1 SPI OPERATIONS........................................................................................................ 10 7.1.1 7.1.2 7.1.3 7.1.4 7.2 WRITE PROTECTION .................................................................................................. 11 7.2.1 8. Standard SPI Instructions ............................................................................................... 10 Dual SPI Instructions ...................................................................................................... 10 Quad SPI Instructions ..................................................................................................... 10 Hold Function .................................................................................................................. 10 Write Protect Features .................................................................................................... 11 CONTROL AND STATUS REGISTERS ................................................................................... 12 8.1 STATUS REGISTER .................................................................................................... 12 8.1.1 8.1.2 8.1.3 8.1.4 8.1.5 8.1.6 8.1.7 8.1.8 8.1.9 8.1.1 8.1.2 8.1.3 8.2 INSTRUCTIONS ........................................................................................................... 17 8.2.1 8.2.2 8.2.3 8.3 BUSY .............................................................................................................................. 12 Write Enable Latch (WEL) .............................................................................................. 12 Block Protect Bits (BP2, BP1, BP0) ................................................................................ 12 Top/Bottom Block Protect (TB) ....................................................................................... 12 Sector/Block Protect (SEC) ............................................................................................. 12 Complement Protect (CMP) ............................................................................................ 12 Protection and Special One time Programming Setting .................................................. 13 Erase/Program Suspend Status (SUS) ........................................................................... 14 Security Register Lock Bits (LB[3:0]) - Volatile/Non-Volatile OTP Writable .................... 14 Quad Enable (QE) .......................................................................................................... 14 Status Register Memory Protection (CMP = 0) ............................................................... 15 Status Register Memory Protection (CMP = 1) ............................................................... 16 Manufacturer and Device Identification ........................................................................... 17 Instruction Set Table 1 (Erase, Program Instructions)(1) ................................................. 18 Instruction Set Table 2 .................................................................................................... 18 Instruction Descriptions ................................................................................................ 20 8.3.1 Write Enable (06h) .......................................................................................................... 20 -2- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.2 8.3.3 8.3.4 8.3.5 8.3.6 8.3.7 8.3.8 8.3.9 8.3.10 8.3.11 8.3.12 8.3.13 8.3.14 8.3.15 8.3.16 8.3.17 8.3.18 8.3.19 8.3.20 8.3.21 8.3.22 8.3.23 8.3.24 8.3.25 8.3.26 8.3.27 8.3.28 8.3.29 8.3.30 9. 10. write Enable for Volatile Status Register (50h) ............................................................... 20 Write Disable (04h) ......................................................................................................... 21 Read Status Register-1 (05h) and Read Status Register-2 (35h) ................................... 21 Write Status Register (01h),Status Register-2 (31h) ....................................................... 22 Read Data (03h) ............................................................................................................. 23 Fast Read (0Bh).............................................................................................................. 24 Fast Read Dual Output (3Bh) ......................................................................................... 25 Fast Read Quad Output (6Bh) ........................................................................................ 26 Fast Read Dual I/O (BBh) ............................................................................................. 27 Fast Read Quad I/O (EBh) ............................................................................................ 28 Set Burst with Wrap (77h) ............................................................................................. 29 Page Program (02h) ..................................................................................................... 30 Quad Input Page Program (32h) ................................................................................... 31 Sector Erase (20h) ........................................................................................................ 32 32KB Block Erase (52h) ................................................................................................ 33 64KB Block Erase (D8h) ............................................................................................... 34 Chip Erase (C7h / 60h) ................................................................................................. 35 Erase / Program Suspend (75h) ................................................................................... 36 Erase / Program Resume (7Ah) .................................................................................... 37 Power-down (B9h) ........................................................................................................ 38 Release Power-down / Device ID (ABh) ....................................................................... 39 Read Manufacturer / Device ID (90h) ........................................................................... 41 Read Manufacturer / Device ID Dual I/O (92h) ............................................................. 42 Read Manufacturer / Device ID Quad I/O (94h) ............................................................ 43 Read Unique ID Number (4Bh) ..................................................................................... 44 Read JEDEC ID (9Fh) .................................................................................................. 45 Erase Security Registers (44h) ..................................................................................... 46 Program Security Registers (42h) ................................................................................. 47 Read Security Registers (48h) ...................................................................................... 48 ELECTRICAL CHARACTERISTICS ......................................................................................... 49 9.1 Absolute Maximum Ratings (1)..................................................................................... 49 9.2 Operating Ranges ......................................................................................................... 49 9.3 Power-up Timing and Write Inhibit Threshold .............................................................. 50 9.4 DC Electrical Characteristics: ....................................................................................... 51 9.5 AC Measurement Conditions ........................................................................................ 52 9.6 AC Electrical Characteristics: ....................................................................................... 53 9.7 AC Electrical Characteristics (cont'd) ........................................................................... 54 9.8 Serial Output Timing ..................................................................................................... 55 9.9 Serial Input Timing ........................................................................................................ 55 9.10 Hold Timing ................................................................................................................... 55 9.11 /WP Timing ................................................................................................................... 55 PACKAGE SPECIFICATION .................................................................................................... 56 10.1 8-Pin SOIC 150-mil (Package Code SN) ...................................................................... 56 10.2 8-Pin VSOP8 150-mil (Package Code SV) ................................................................... 57 10.3 8-Pad USON 2x3x0.6-mm^ (Package Code UX) ........................................................ 58 -3- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 11. 12. 10.4 8-Pad -mm (Package Code BY) ................................................................................... 59 ORDERING INFORMATION..................................................................................................... 60 11.1 Valid Part Numbers and Top Side Marking .................................................................. 61 REVISION HISTORY ................................................................................................................ 62 -4- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 1. GENERAL DESCRIPTION The W25Q20EW (2M-bit) Serial Flash memories provide a storage solution for systems with limited space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP) and storing voice, text and data. The device operates on a single 1.65V to 1.95V power supply with current consumption as low as 1A for power-down. All devices are offered in spacesaving packages. The W25Q20EW array are organized into 1,024 programmable pages of 256-bytes each. Up to 256 bytes can be programmed at a time. The W25Q20EW have 64 erasable sectors, 8 erasable 32KB blocks and 4 erasable 64KB blocks respectively. The small 4KB sectors allow for greater flexibility in applications that require data and parameter storage. (See figure 2.) The W25Q20EW support the standard Serial Peripheral Interface (SPI), and a high performance Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1 (DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for Quad I/O when using the Fast Read Dual/Quad I/O instructions. These transfer rates can outperform standard Asynchronous 8 and 16-bit Parallel Flash memories. A Hold pin, Write Protect pin and programmable write protect, with top, bottom or complement array control, provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and device identification with a 64-bit Unique Serial Number. 2. FEATURES - Min. 100K Program-Erase cycles per sector Family of SpiFlash Memories - 2M-bit/256K-byte (262,144) - 256-byte per programmable page - Uniform 4KB Sectors, 32KB & 64KB Blocks Advanced Security Features - Power Supply Lock-Down - Speical OTP protection - Top/Bottom, Complement array protection - 4X256-Byte Security Registers with OTP locks - Volatile & Non-volatile Status Register Bits SPI with Single / Dual Outputs / I/O - Standard SPI: CLK, /CS, DI, DO, /WP, /Hold - Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold - Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3 Low Power, Wide Temperature Range - Single 1.65 to 1.95V supply - 1mA active current, <1A Power-down(typ.) - Industrial:-40C to +85C operating range Data Transfer up to 50MB / second - Clock operation to 104MHz. - 208/416MHz equivalent Dual/Quad SPI - Auto-increment Read capability. Space Efficient Packaging - 8-pin SOIC/VSOP 150-mil - 8-pad USON8 2X3mm - 8-ball WLCSP - Contact Winbond for KGD and other options Flexible Architecture with 4KB sectors - Uniform Sector/Block Erase (4/32/64-kbytes) - Program one to 256 bytes < 1ms - Erase/Program Suspend & Resume - More than 20-year data retention -5- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 4. PACKAGE TYPES AND PIN CONFIGURATIONS W25Q20EW are offered in an 8-pin plastic 150-mil width SOIC (package code SN), 150-mil width VSOP (package code SV), 2x3-mm USON (package code UX) and an 8-pad WLCSP. Refer to see figures 1a1c, respectively. 4.1 Pin Configuration SOIC 150-mil and VSOP 150-mil Figure 1a.W25Q20EW Pin Assignments, 8-pin SOIC 150-mil and VSOP 150-mil (Package Code SN & SV) 4.2 PAD Configuration USON 2x3-mm Figure 1b.W25Q20EW Pad Assignments USON 2x3-mm (Package Code UX) 4.3 Pin Description SOIC/ VSOP 150-mil, USON 2x3-mm PIN NO. PIN NAME I/O FUNCTION 1 /CS I 2 DO (IO1) I/O Data Output (Data Input Output 1)(1) (2) 3 /WP (IO2) I/O Write Protect Input ( Data Input Output 2) (2) 4 GND 5 DI (IO0) I/O 6 CLK I 7 /HOLD (IO3) I/O 8 VCC Chip Select Input Ground Data Input (Data Input Output 0) (1) (2) Serial Clock Input Hold Input (Data Input Output 3) (2) Power Supply Note: 1 IO0 and IO1 are used for Standard and Dual SPI instructions 2 IO0 - IO3 are used for Quad SPI instructions -6- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 4.4 Ball Configuration WLCSP Figure 1c. W25Q20EW Ball Assignments, 8-ball WLCSP (Package Code BY) 4.5 Ball Description WLCSP BALL NO. PIN NAME I/O FUNCTION A1 VCC A2 /HOLD or /RESET (IO3) I/O A3 /CS I Chip Select Input B1 CLK I Serial Clock Input B2 DO (IO1) I/O Data Output (Data Input Output 1)(1) C1 DI (IO0) I/O Data Input (Data Input Output 0)(1) C2 /WP (IO2) I/O Write Protect Input (Data Input Output 2)(2) C3 GND Power Supply Hold or Reset Input (Data Input Output 3)(2) Ground Notes: 1. IO0 and IO1 are used for Standard and Dual SPI instructions 2. IO0 - IO3 are used for Quad SPI instructions, /WP & /HOLD (or /RESET) functions are only available for Standard/Dual SPI. -7- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 5. PIN DESCRIPTIONS 5.1 Chip Select (/CS) The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When deselected, the devices power consumption will be at standby levels unless an internal erase, program or write status register cycle is in progress. When /CS is brought low the device will be selected, power consumption will increase to active levels and instructions can be written to and data read from the device. After power-up, /CS must transition from high to low before a new instruction will be accepted. The /CS input must track the VCC supply level at power-up (see "Power-up Timing and Write inhibit threshold" and figure 35). If needed, a pull-up resister on /CS can be used to accomplish this. 5.2 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3) The W25Q20EW support standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions use the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read data or status from the device on the falling edge of CLK. Dual and Quad SPI instructions use the bidirectional IO pins to serially write instructions, addresses or data to the device on the rising edge of CLK and read data or status from the device on the falling edge of CLK. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register 2 to be set. When QE=1, the /WP pin becomes IO2 and /HOLD pin becomes IO3. 5.3 Write Protect (/WP) The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in conjunction with the Status Register's Block Protect (CMP, SEC, TB, BP2, BP1 and BP0) bits and Status Register Protect (SRP) bits, a portion as small as 4KB sector or the entire memory array can be hardware protected. The /WP pin is active low. When the QE bit of Status Register-2 is set for Quad I/O, the /WP pin function is not available since this pin is used for IO2. 5.4 HOLD (/HOLD) The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought low, while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored (don't care). When /HOLD is brought high, device operation can resume. The /HOLD function can be useful when multiple devices are sharing the same SPI signals. The /HOLD pin is active low. When the QE bit of Status Register-2 is set for Quad I/O, the /HOLD pin function is not available since this pin is used for IO3. See figure 1a and 1b for the pin configuration of Quad I/O operation. 5.5 Serial Clock (CLK) The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. -8- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 6. BLOCK DIAGRAM Security Register 3 - 0 Block Segmentation xxFF00h * xxF000h Sector 15 (4KB) xxFFFFh * xxF0FFh xxEF00h * xxE000h Sector 14 (4KB) xxEFFFh * xxE0FFh xxDF00h * xxD000h Sector 13 (4KB) xxDFFFh * xxD0FFh 03FF00h * 030000h /WP (IO 2) xx2F00h * xx2000h Sector 2 (4KB) xx2FFFh * xx20FFh xx1F00h * xx1000h Sector 1 (4KB) xx1FFFh * xx10FFh xx0F00h * xx0000h Sector 0 (4KB) xx0FFFh * xx00FFh Write Protect Logic and Row Decode * * * 0030FFh 0020FFh 0010FFh 0000FFh Block 3 (64KB) 03FFFFh * 0300FFh W25Q20BW W25Q20EW 003000h 002000h 001000h 000000h * * * Write Control Logic Status Register High Voltage Generators /HOLD (IO 3) CLK /CS SPI Command & Control Logic Page Address Latch / Counter 01FF00h * 010000h Block 1 (64KB) 01FFFFh * 0100FFh 00FF00h * 000000h Block 0 (64KB) 00FFFFh * 0000FFh Beginning Page Address Ending Page Address Column Decode And 256-Byte Page Buffer Data DI (IO 0) DO (IO 1) Byte Address Latch / Counter Figure 2.W25Q20EW Serial Flash Memory Block Diagram -9- Publication Release Date: July 28, 2015 -Revision D W25Q20EW 7. FUNCTIONAL DESCRIPTION 7.1 SPI OPERATIONS 7.1.1 Standard SPI Instructions The W25Q20EW are accessed through an SPI compatible bus consisting of four signals: Serial Clock (CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of CLK. The DO output pin is used to read data or status from the device on the falling edge CLK. SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the falling and rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising edges of /CS. 7.1.2 Dual SPI Instructions The W25Q20EW support Dual SPI operation when using the "Fast Read Dual Output (3Bh)" and "Fast Read Dual I/O (BBh)" instructions. These instructions allow data to be transferred to or from the device at two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read instructions are ideal for quickly downloading code to RAM upon power-up (code-shadowing) or for executing non-speedcritical code directly from the SPI bus (XIP). When using Dual SPI instructions, the DI and DO pins become bidirectional I/O pins: IO0 and IO1. 7.1.3 Quad SPI Instructions The W25Q20EW support Quad SPI operation when using the "Fast Read Quad Output (6Bh)", "Fast Read Quad I/O (EBh)" instructions. These instructions allow data to be transferred to or from the device six to eight times the rate of ordinary Serial Flash. The Quad Read instructions offer a significant improvement in continuous and random access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP). When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register 2 to be set. 7.1.4 Hold Function For Standard SPI and Dual SPI operations, the /HOLD signal allows the W25Q20EW operation to be paused while it is actively selected (when /CS is low). The /HOLD function may be useful in cases where the SPI data and clock signals are shared with other devices. For example, consider if the page buffer was only partially written when a priority interrupt requires use of the SPI bus. In this case the /HOLD function can save the state of the instruction and the data in the buffer so programming can resume where it left off once the bus is available again. The /HOLD function is only available for standard SPI and Dual SPI operation, not during Quad SPI. - 10 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip Select (/CS) signal should be kept active low for the full duration of the /HOLD operation to avoid resetting the internal logic state of the device. 7.2 WRITE PROTECTION Applications that use non-volatile memory must take into consideration the possibility of noise and other adverse system conditions that may compromise data integrity. To address this concern, the W25Q20EW provide several means to protect the data from inadvertent writes. 7.2.1 Write Protect Features Device resets when VCC is below threshold Time delay write disable after Power-up Write enable/disable instructions Automatic write disable after erase or program Software and Hardware (/WP pin) write protection using Status Register Write Protection using Power-down instruction Lock Down write protection until next power-up One Time Program (OTP) write protection* * Note: This feature is available upon special order. Please contact Winbond for details. Upon power-up or at power-down, the W25Q20EW will maintain a reset condition while VCC is below the threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 35). While reset, all operations are disabled and no instructions are recognized. During power-up and after the VCC voltage exceeds VWI, all program and erase related instructions are further disabled for a time delay of tPUW. This includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at power-up until the VCC-min level and tVSL time delay is reached. If needed, a pull-up resister on /CS can be used to accomplish this. After power-up the device is automatically placed in a write-disabled state with the Status Register Write Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a program, erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-disabled state of 0. Software controlled write protection is facilitated using the Write Status Register instruction and setting the Status Register Protect (SRP, SRL) and Block Protect (CMP, SEC,TB, BP2, BP1 and BP0) bits. These settings allow a portion as small as 4KB sector or the entire memory array to be configured as read only. Used in conjunction with the Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware control. See Status Register section for further information. Additionally, the Power-down instruction offers an extra level of write protection as all instructions are ignored except for the Release Power-down instruction. - 11 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8. CONTROL AND STATUS REGISTERS The Read Status Register-1 and Status Register-2 instructions can be used to provide status on the availability of the Flash memory array, if the device is write enabled or disabled, the state of write protection, Quad SPI setting, Security Register lock status and Erase/Program Suspend status. The Write Status Register instruction can be used to configure the device write protection features, Quad SPI setting and Security Register OTP lock. Write access to the Status Register is controlled by the state of the non-volatile Status Register Protect bits (SRP, SRL), the Write Enable instruction, and during Standard/Dual SPI operations, the /WP pin. 8.1 STATUS REGISTER 8.1.1 BUSY BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register or Erase/Program Security Register instruction. During this time the device will ignore further instructions except for the Read Status Register and Erase/Program Suspend instruction (see tW, tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status/security register instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready for further instructions. 8.1.2 Write Enable Latch (WEL) Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to 1 after executing a Write Enable Instruction. The WEL status bit is cleared to 0 when the device is write disabled. A write disable state occurs upon power-up or after any of the following instructions finished: Write Disable, Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register, Erase Security Register and Program Security Register. 8.1.3 Block Protect Bits (BP2, BP1, BP0) The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3, and S2) that provide Write Protection control and status. Block Protect bits can be set using the Write Status Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be protected from Program and Erase instructions (see Status Register Memory Protection table). The factory default setting for the Block Protection Bits is 0, none of the array protected. 8.1.4 Top/Bottom Block Protect (TB) The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The factory default setting is TB=0. The TB bit can be set with the Write Status Register Instruction depending on the state of the SRP, SRL and WEL bits. 8.1.5 Sector/Block Protect (SEC) The non-volatile Sector/Block Protect bit (SEC) controls if the Block Protect Bits (BP2, BP1, BP0) protect either 4KB Sectors (SEC=1) or 64KB Blocks (SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table. The default setting is SEC=0. 8.1.6 Complement Protect (CMP) The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used in conjunction with SEC, TB, BP2, BP1 and BP0 bits to provide more flexibility for the array protection. Once CMP is set to 1, previous array protection set by SEC, TB, BP2, BP1 and BP0 will be reversed. - 12 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW For instance, when CMP=0, a top 4KB sector can be protected while the rest of the array is not; when CMP=1, the top 4KB sector will become unprotected while the rest of the array become read-only. Please refer to the Status Register Memory Protection table for details. The default setting is CMP=0. 8.1.7 Protection and Special One time Programming Setting The Status Register Protect bits (SRP) are non-volatile read/write bits in the status register (S7). The SRP bit controls the method of write protection: software protection or hardware protection. The Status Register Lock bits (SRL) are non-volatile/volatile read/write bits in the status register (S8). The SRL bit controls the method of write protection: temporary lock-down or permanently one time program. SRP /WP 0 X 0 Status Protection Software Protection Hardware Protected Description /WP pin has no control. The Status register can be written to after a Write Enable instruction, WEL=1. [Factory Default] When /WP pin is low the Status Register can not be written to. 1 1 SRL 0 Hardware Unprotected Status Register Lock Non-Lock Lock-Down When /WP pin is high the Status register can be written to after a Write Enable instruction, WEL=1. Description Status Register is unlocked (1) (temporary/Volatile) Status Register is locked by standard status register write command and can not be written to again until the next power-down, power-up cycle. 1 One Time Program (2) (Permanently/Non-Volatile) Status Register is permanently locked by special * command flow and can not be written to 1. When SRP =1 , a power-down, power-up cycle will change SRP =0 state. 2. One Time Protection feature is available upon special order; please contact Winbond for details - 13 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.1.8 Erase/Program Suspend Status (SUS) The Suspend Status bit is a read only bit in the status register (S15) that is set to 1 after executing a Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume (7Ah) instruction as well as a power-down, power-up cycle. 8.1.9 Security Register Lock Bits (LB[3:0]) - Volatile/Non-Volatile OTP Writable The Security Register Lock Bits (LB3, LB2, LB1, LB0) are non-volatile One Time Program (OTP) bits in Status Register (S13, S12, S11, S10) that provide the write protect control and status to the Security Registers. The default state of LB3-0 is 0, Security Registers are unlocked. LB3-0 can be set to 1 individually using the Write Status Register instruction. LB3-0 are One Time Programmable (OTP), once it's set to 1, the corresponding 256-Byte Security Register will become read-only permanently. 8.1.1 Quad Enable (QE) The Quad Enable (QE) bit is a non-volatile read/write bit in the status register (S9) that allows Quad SPI and QPI operation. When the QE bit is set to a 0 state (factory default for part number with ordering options "IG" and "IE"), the /WP pin and /HOLD are enabled. When the QE bit is set to a 1(factory default for Quad Enabled part numbers with ordering option "IQ"), the Quad IO2 and IO3 pins are enabled, and /WP and /HOLD functions are disabled. WARNING: If the /WP or /HOLD pins are tied directly to the power supply or ground during standard SPI or Dual SPI operation, the QE bit should never be set to a 1. S7 S6 S5 S4 S3 S2 S1 S0 SRP SEC TB BP2 BP1 BP0 WEL BUSY STATUS REGISTER PROTECT ( Non - volatile ) SECTOR PROTECT (Non - volatile) TOP/ BOTTOM PROTECT ( Non - volatile ) BLOCK PROTECT BITS ( Non - volatile ) WRITE ENABLE LATCH ERASE/ WRITE IN PROGRESS ( volatile) Figure 3a. Status Register-1 S15 S14 S13 S12 S11 S10 S9 S8 SUS CMP LB3 LB2 LB1 LB0 QE SRP1 Suspend Status (Status-Only) Complement Protect (Volatile/Non-Volatile Writable) Security Register Lock Bits (Volatile/Non-Volatile OTP Writable) Quad Enable (Volatile/Non-Volatile Writable) Status Register Protect 1 (Volatile/Non-Volatile Writable) Figure 3b. Status Register-2 - 14 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.1.2 Status Register Memory Protection (CMP = 0) STATUS REGISTER(1) 2M-BIT MEMORY PROTECTED(2) SEC TB BP2 BP1 BP0 BLOCK(S) ADDRESSES DENSITY PORTION 0 0 0 X 0 0 X X X 0 0 1 0 1 0 NONE 3 2 and 3 NONE 030000h - 03FFFFh 020000h - 03FFFFh NONE 64KB 128KB NONE Upper 1/4 Upper 1/2 0 0 0 1 1 X X X X 0 1 1 1 0 1 0 0 and 1 0 thru 3 000000h - 00FFFFh 000000h - 01FFFFh 000000h - 03FFFFh 64KB 128KB 256KB Lower 1/4 Lower 1/2 ALL 1 1 1 1 1 1 X 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 X 0 NONE 3 3 3 3 3 NONE 03F000h - 03FFFFh 03E000h - 03FFFFh 03C000h - 03FFFFh 038000h - 03FFFFh 038000h - 03FFFFh NONE 4KB 8KB 16KB 32KB 32KB NONE Upper 1/64 Upper 1/32 Upper 1/16 Upper 1/8 Upper 1/8 1 1 1 1 1 1 1 1 1 1 1 X 0 0 0 1 1 1 0 1 1 0 1 1 1 0 1 X 0 1 0 0 0 0 0 0 thru 3 000000h - 000FFFh 000000h - 001FFFh 000000h - 003FFFh 000000h - 007FFFh 000000h - 007FFFh 000000h - 03FFFFh 4KB 8KB 16KB 32KB 32KB 256KB Lower 1/64 Lower 1/32 Lower 1/16 Lower 1/8 Lower 1/8 ALL Notes: 1. X = don't care 2. If any Erase or Program command specifies a memory region that contains protected data portion, this command will be ignored. - 15 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.1.3 Status Register Memory Protection (CMP = 1) STATUS REGISTER(1) 2M-BIT MEMORY PROTECTED(2) SEC TB BP2 BP1 BP0 BLOCK(S) ADDRESSES DENSITY PORTION 0 0 0 X 0 0 X X X 0 0 1 0 1 0 0 thru 3 0 thru 2 0 and 1 000000h - 03FFFFh 000000h - 02FFFFh 000000h - 01FFFFh 256KB 192KB 128KB ALL Lower 3/4 Lower 1/2 0 0 0 1 1 X X X X 0 1 1 1 0 1 1 thru 3 2 and 3 NONE 010000h - 03FFFFh 020000h - 03FFFFh NONE 192KB 128KB NONE Upper 3/4 Upper 1/2 NONE 1 1 1 1 1 1 X 0 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 X 0 0 thru 3 0 thru 3 0 thru 3 0 thru 3 0 thru 3 0 thru 3 000000h - 03FFFFh 000000h - 03EFFFh 000000h - 03DFFFh 000000h - 03BFFFh 000000h - 037FFFh 000000h - 037FFFh 256KB 252KB 248KB 240KB 224KB 224KB ALL Lower 63/64 Lower 31/32 Lower 15/16 Lower 7/8 Lower 7/8 1 1 1 1 1 1 1 1 1 1 1 X 0 0 0 1 1 1 0 1 1 0 1 1 1 0 1 X 0 1 0 thru 3 0 thru 3 0 thru 3 0 thru 3 0 thru 3 NONE 001000h - 03FFFFh 002000h - 03FFFFh 004000h - 03FFFFh 008000h - 03FFFFh 008000h - 03FFFFh NONE 252KB 248KB 240KB 224KB 224KB NONE Upper 63/64 Upper 31/32 Upper 15/16 Upper 7/8 Upper 7/8 NONE Notes: 3. X = don't care 4. If any Erase or Program command specifies a memory region that contains protected data portion, this command will be ignored. - 16 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.2 INSTRUCTIONS The instruction set of the W25Q20EW consists of thirty three basic instructions that are fully controlled through the SPI bus (see Instruction Set table). Instructions are initiated with the falling edge of Chip Select (/CS). The first byte of data clocked into the DI input provides the instruction code. Data on the DI input is sampled on the rising edge of clock with most significant bit (MSB) first. Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data bytes, dummy bytes (don't care), and in some cases, a combination. Instructions are completed with the rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in figures 4 through 34. All read instructions can be completed after any clocked bit. However, all instructions that Write, Program or Erase must complete on a byte boundary (/CS driven high after a full 8-bits have been clocked) otherwise the instruction will be ignored. This feature further protects the device from inadvertent writes. Additionally, while the memory is being programmed or erased, or when the Status Register is being written, all instructions except for Read Status Register will be ignored until the program or erase cycle has completed. 8.2.1 Manufacturer and Device Identification MANUFACTURER ID (MF7-MF0) Winbond Serial Flash EFh Device ID (ID7-ID0) (ID15-ID0) Instruction ABh, 90h, 92h, 94h 9Fh W25Q20EW 11h 6012h - 17 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.2.2 Instruction Set Table 1 (Erase, Program Instructions)(1) Data Input Output Number of Clock(1-1-1) Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 8 8 8 8 8 8 8 Dummy Dummy Dummy (ID7-ID0)(2) (MF7-MF0) (ID7-ID0) (UID63-0) Write Enable 06h Volatile SR Write Enable 50h Write Disable 04h Release Power-down / ID Manufacturer/Device ID (4) ABh 90h Dummy Dummy 00h JEDEC ID 9Fh (MF7-MF0) (ID15-ID8) (ID7-ID0) Read Unique ID 4Bh Dummy Dummy Dummy Dummy Read Data 03h A23-A16 A15-A8 A7-A0 (D7-D0) Fast Read 0Bh A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Page Program 02h A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) Sector Erase (4KB) 20h A23-A16 A15-A8 A7-A0 Block Erase (32KB) 52h A23-A16 A15-A8 A7-A0 D8h A23-A16 A15-A8 A7-A0 Block Erase (64KB) Chip Erase C7h/60h (S7-S0)(2) Read Status Register-1 05h Write Status Register-1(4) 01h (S7-S0)(4) Read Status Register-2 35h (S15-S8)(2) 31h (S15-S8) 44h A23-A16 A15-A8 A7-A0 42h A23-A16 A15-A8 A7-A0 D7-D0 D7-D0(3) 48h A23-A16 A15-A8 A7-A0 Dummy (D7-D0) Write Status Register-2 Erase Security Register (5) Program Security Register(5) Read Security Register (5) Erase / Program Suspend 75h Erase / Program Resume 7Ah Power-down B9h 8.2.3 Instruction Set Table 2 Data Input Output Number of Clock(1-1-2) Byte 1 8 Byte 2 8 Byte 3 8 Byte 4 8 Byte 5 4 Byte 6 4 Byte 7 4 Fast Read Dual Output 3Bh A23-A16 A15-A8 A7-A0 Dummy Dummy (D7-D0)(7) Number of Clock(1-2-2) 8 4 4 4 4 4 4 (2) (2) A7-A0 00(2) Fast Read Dual I/O BBh A23-A16 A15-A8 Mftr./Device ID Dual I/O 92h A23-A16(2) A15-A8(2) Number of Clock(1-1-4) (2) (11) Dummy Dummy(11) (D7-D0) Byte 8 4 4 (1) (MF7-MF0) (ID7-ID0) 2 8 8 8 8 2 2 Quad Input Page Program 32h A23-A16 A15-A8 A7-A0 (D7-D0)(9) (D7-D0)(3) Fast Read Quad Output 6Bh A23-A16 A15-A8 A7-A0 Dummy Dummy Dummy (D7-D0)(9) Number of Clock(1-4-4) 8 2 2 2 2 2 2 2 Mftr./Device ID Quad I/O 94h A23-A16 A15-A8 00 Dummy(11) Dummy Dummy (MF7-MF0) Fast Read Quad I/O EBh A23-A16 A15-A8 A7-A0 Dummy(11) Dummy Dummy (D7-D0) Set Burst with Wrap 77h Dummy Dummy Dummy W8-W0 - 18 - 2 ... Publication Release Date: July 28, 2015 -Revision D W25Q20EW Notes: 1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis "( )" indicate data output from the device on either 1, 2 or 4 IO pins. 2. The Status Register contents and Device ID will repeat continuously until /CS terminates the instruction. 3. At least one byte of data input is required for Page Program, Quad Page Program and Program Security Registers, up to 256 bytes of data input. If more than 256 bytes of data are sent to the device, the addressing will wrap to the beginning of the page and overwrite previously sent data. 4. Write Status Register-1 (01h) can also be used to program Status Register-1&2, see section 8.2.5. 5. Security Register Address: Security Register 0: A23-16 = 00h; A15-8 = 00h; A7-0 = byte address Security Register 1: A23-16 = 00h; A15-8 = 10h; A7-0 = byte address Security Register 2: A23-16 = 00h; A15-8 = 20h; A7-0 = byte address Security Register 3: A23-16 = 00h; A15-8 = 30h; A7-0 = byte address 6. Dual SPI address input format: IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0 IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1 7. Dual SPI data output format: IO0 = (D6, D4, D2, D0) IO1 = (D7, D5, D3, D1) 8. Quad SPI address input format: Set Burst with Wrap input format: IO0 = A20, A16, A12, A8, A4, A0, M4, M0 IO0 = x, x, x, x, x, x, W4, x IO1 = A21, A17, A13, A9, A5, A1, M5, M1 IO1 = x, x, x, x, x, x, W5, x IO2 = A22, A18, A14, A10, A6, A2, M6, M2 IO2 = x, x, x, x, x, x, W6, x IO3 = A23, A19, A15, A11, A7, A3, M7, M3 IO3 = x, x, x, x, x, x, x, x 9. Quad SPI data input/output format: IO0 = (D4, D0, .....) IO1 = (D5, D1, .....) IO2 = (D6, D2, .....) IO3 = (D7, D3, .....) 10. Fast Read Quad I/O data output format: IO0 = (x, x, x, x, D4, D0, D4, D0) IO1 = (x, x, x, x, D5, D1, D5, D1) IO2 = (x, x, x, x, D6, D2, D6, D2) IO3 = (x, x, x, x, D7, D3, D7, D3) 11. The first dummy is M7-M0 should be set to FFh - 19 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3 Instruction Descriptions 8.3.1 Write Enable (06h) The Write Enable instruction (Figure 4) sets the Write Enable Latch (WEL) bit in the Status Register to a 1. The WEL bit must be set prior to every Page Program, Quad Page Program, Sector Erase, Block Erase, Chip Erase, Write Status Register and Erase/Program Security Registers instruction. The Write Enable instruction is entered by driving /CS low, shifting the instruction code "06h" into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 3 Mode 0 Instruction (06h) DI (IO0) DO (IO1) High Impedance Figure 4. Write Enable Instruction Sequence Diagram 8.3.2 write Enable for Volatile Status Register (50h) The non-volatile Status Register bits described in section 8.1 can also be written to as volatile bits. This gives more flexibility to change the system configuration and memory protection schemes quickly without waiting for the typical non-volatile bit write cycles or affecting the endurance of the Status Register non-volatile bits. To write the volatile values into the Status Register bits, the Write Enable for Volatile Status Register (50h) instruction must be issued prior to a Write Status Register (01h) instruction. Write Enable for Volatile Status Register instruction (Figure 5) will not set the Write Enable Latch (WEL) bit, it is only valid for the Write Status Register instruction to change the volatile Status Register bit values. Instruction (50h) Figure 5. Write Enable for Volatile Status Register Instruction Sequence Diagram - 20 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.3 Write Disable (04h) The Write Disable instruction (Figure 6) resets the Write Enable Latch (WEL) bit in the Status Register to a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code "04h" into the DI pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon completion of the Write Status Register. Erase/Program Security Registers, Page Program, Quad Page Program, Sector Erase, Block Erase and Chip Erase instructions. Write Disable instruction can also be used to invalidate the Write Enable for Volatile Status Register instruction Figure 6. Write Disable Instruction Sequence Diagram 8.3.4 Read Status Register-1 (05h) and Read Status Register-2 (35h) The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is entered by driving /CS low and shifting the instruction code "05h" for Status Register-1 or "35h" for Status Register-2 into the DI pin on the rising edge of CLK. The status register bits are then shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in figure 7. The Status Register bits are shown in figure 3a and 3b and include the BUSY, WEL, BP2-BP0, TB, SEC, SRP, SRL, QE, LB[3:0f], CMP and SUS bits (see Status Register section earlier in this datasheet). The Read Status Register instruction may be used at any time, even while a Program, Erase or Write Status Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the cycle is complete and if the device can accept another instruction. The Status Register can be read continuously, as shown in Figure 7. The instruction is completed by driving /CS high. Figure 7. Read Status Register Instruction Sequence Diagram - 21 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.5 Write Status Register (01h),Status Register-2 (31h) The Write Status Register instruction allows the Status Register to be written. Only non-volatile Status Register bits SRP, SEC, TB, BP2, BP1, BP0 (bits 7 thru 2 of Status Register-1) and CMP, LB[3:0], QE, SRL (bits 14 thru 8 of Status Register-2) can be written to. All other Status Register bit locations are read-only and will not be affected by the Write Status Register instruction. LB[3:0] are non-volatile OTP bits, once it is set to 1, it cannot be cleared to 0. The Status Register bits are shown in figure 3 and described in 7.1. To write non-volatile Status Register bits, a standard Write Enable (06h) instruction must previously have been executed for the device to accept the Write Status Register Instruction (Status Register bit WEL must equal 1). Once write enabled, the instruction is entered by driving /CS low, sending the instruction code "01h/31h", and then writing the status register data byte as illustrated in figure 8. To write volatile Status Register bits, a Write Enable for Volatile Status Register (50h) instruction must have been executed prior to the Write Status Register instruction (Status Register bit WEL remains 0). However, SRL and LB[3:0] cannot be changed from "1" to "0" because of the OTP protection for these bits. Upon power off, the volatile Status Register bit values will be lost, and the non-volatile Status Register bit values will be restored when power on again. To complete the Write Status Register instruction, the /CS pin must be driven high after the eighth or sixteenth bit of data that is clocked in. If this is not done the Write Status Register instruction will not be executed. If /CS is driven high after the eighth clock, the Write Status Register-1 (01h) instruction will only program the Status Register-1, the Status Register-2 will not be affected (Previous generations will clear CMP and QE bits). During non-volatile Status Register write operation (06h combined with 01h/31h), after /CS is driven high, the self-timed Write Status Register cycle will commence for a time duration of tW (See AC Characteristics). While the Write Status Register cycle is in progress, the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle and a 0 when the cycle is finished and ready to accept other instructions again. After the Write Status Register cycle has finished, the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0. During volatile Status Register write operation (50h combined with 01h/31h), after /CS is driven high, the Status Register bits will be refreshed to the new values within the time period of tSHSL2 (See AC Characteristics). BUSY bit will remain 0 during the Status Register bit refresh period. Please refer to 10.1 for detailed Status Register Bit descriptions. Factory default for all status Register bits are 0 . /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Mode 0 Instruction (01h) DI (IO0) Mode 3 Status Register 1 in 7 6 5 4 3 * 2 Status Register 2 in 1 0 15 14 13 12 11 10 9 8 * High Impedance DO (IO1) * = MSB Figure 8. Write Status Register Instruction Sequence Diagram - 22 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.6 Read Data (03h) The Read Data instruction allows one or more data bytes to be sequentially read from the memory. The instruction is initiated by driving the /CS pin low and then shifting the instruction code "03h" followed by a 24-bit address (A23-A0) into the DI pin. The code and address bits are latched on the rising edge of the CLK pin. After the address is received, the data byte of the addressed memory location will be shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The address is automatically incremented to the next higher address after each byte of data is shifted out allowing for a continuous stream of data. This means that the entire memory can be accessed with a single instruction as long as the clock continues. The instruction is completed by driving /CS high. The Read Data instruction sequence is shown in figure 9. If a Read Data instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of fR (see AC Electrical Characteristics). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 Instruction (03h) DI (IO0) 24-Bit Address 23 22 21 3 2 1 0 * Data Out 1 High Impedance DO (IO1) * 7 6 5 4 3 2 1 0 7 * = MSB Figure 9. Read Data Instruction Sequence Diagram - 23 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.7 Fast Read (0Bh) The Fast Read instruction is similar to the Read Data instruction except that it can operate at the highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24-bit address as shown in figure 10. The dummy clocks allow the devices internal circuits additional time for setting up the initial address. During the dummy clocks the data value on the DO pin is a "don't care". /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (0Bh) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK Dummy Clocks DI (IO0) DO (IO1) 0 High Impedance Data Out 1 7 6 5 4 * 3 Data Out 2 2 1 0 7 6 5 4 3 2 1 0 7 * Figure 10. Fast Read Instruction Sequence Diagram - 24 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.8 Fast Read Dual Output (3Bh) The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction except that data is output on two pins, IO0 and IO1. This allows data to be transferred from the W25Q20EW at twice the rate of standard SPI devices. The Fast Read Dual Output instruction is ideal for quickly downloading code from Flash to RAM upon power-up or for applications that cache codesegments to RAM for execution. Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24-bit address as shown in figure 11. The dummy clocks allow the device's internal circuits additional time for setting up the initial address. The input data during the dummy clocks is "don't care". However, the IO0 pin should be high-impedance prior to the falling edge of the first data out clock. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (3Bh) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK IO0 switches from Input to Output Dummy Clocks DI (IO0) DO (IO1) 0 6 High Impedance 7 * 4 2 0 6 5 3 1 7 Data Out 1 * 4 2 0 6 5 3 1 7 Data Out 2 * 4 2 0 6 5 3 1 7 Data Out 3 * 4 2 0 6 5 3 1 7 Data Out 4 Figure 11. Fast Read Dual Output Instruction Sequence Diagram - 25 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.9 Fast Read Quad Output (6Bh) The Fast Read Quad Output (6Bh) instruction is similar to the Fast Read Dual Output (3Bh) instruction except that data is output on four pins, IO0, IO1, IO2, and IO3. A Quad enable of Status Register-2 must be executed before the device will accept the Fast Read Quad Output Instruction (Status Register bit QE must equal 1). The Fast Read Quad Output Instruction allows data to be transferred from the W25Q20EW at four times the rate of standard SPI devices. The Fast Read Quad Output instruction can operate at the highest possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight "dummy" clocks after the 24-bit address as shown in figure 12. The dummy clocks allow the device's internal circuits additional time for setting up the initial address. The input data during the dummy clocks is "don't care". However, the IO pins should be high-impedance prior to the falling edge of the first data out clock. Figure 12. Fast Read Quad Output Instruction Sequence Diagram - 26 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.10 Fast Read Dual I/O (BBh) The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to input the Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code execution (XIP) directly from the Dual SPI in some applications. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (BBh) A23-16 A15-8 A7-0 M7-0 DI (IO0) 22 20 18 16 14 12 10 8 6 4 2 0 6 4 2 0 DO (IO1) 23 21 19 17 15 13 11 9 7 5 3 1 7 5 3 1 * * = MSB * /CS 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 CLK IOs switch from Input to Output DI (IO0) 0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 6 DO (IO1) 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 * Byte 1 * Byte 2 * Byte 3 * Byte 4 Figure 13a. Fast Read Dual I/O Instruction Sequence (Bits M7-0 must be set to FFh) - 27 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.11 Fast Read Quad I/O (EBh) The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except that address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 and four Dummy clock are required prior to the data output. The Quad I/O dramatically reduces instruction overhead allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit (QE) of Status Register-2 must be set to enable the Fast Read Quad I/O Instruction. Byte 1 Byte 2 Figure 14a. Fast Read Quad I/O Instruction Sequence (Bits M7-0 must be set to FFh) Fast Read Quad I/O with "8/16/32/64-Byte Wrap Around" The Fast Read Quad I/O instruction can also be used to access a specific portion within a page by issuing a "Set Burst with Wrap" command prior to EBh. The "Set Burst with Wrap" command can either enable or disable the "Wrap Around" feature for the following EBh commands. When "Wrap Around" is enabled, the data being accessed can be limited to either a 8, 16, 32 or 64-byte section of a 256-byte page. The output data starts at the initial address specified in the instruction, once it reaches the ending boundary of the 8/16/32/64-byte section, the output will wrap around to the beginning boundary automatically until /CS is pulled high to terminate the command. The Burst with Wrap feature allows applications that use cache to quickly fetch a critical address and then fill the cache afterwards within a fixed length (8/16/32/64-byte) of data without issuing multiple read commands. The "Set Burst with Wrap" instruction allows three "Wrap Bits", W6-4 to be set. The W4 bit is used to enable or disable the "Wrap Around" operation while W6-5 are used to specify the length of the wrap around section within a page. See 8.2.18 for detail descriptions. - 28 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.12 Set Burst with Wrap (77h) The Set Burst with Wrap (77h) instruction is used in conjunction with "Fast Read Quad I/O" and "Word Read Quad I/O" instructions to access a fixed length of 8/16/32/64-byte section within a 256-byte page. Certain applications can benefit from this feature and improve the overall system code execution performance. Similar to a Quad I/O instruction, the Set Burst with Wrap instruction is initiated by driving the /CS pin low and then shifting the instruction code "77h" followed by 24 dummy bits and 8 "Wrap Bits", W7-0. The instruction sequence is shown in figure 15. Wrap bit W7 and the lower nibble W3-0 are not used. W4 = 0 W6, W5 0 0 1 1 W4 =1 (DEFAULT) Wrap Around Wrap Length Wrap Around Wrap Length Yes Yes Yes Yes 8-byte 16-byte 32-byte 64-byte No No No No N/A N/A N/A N/A 0 1 0 1 Once W6-4 is set by a Set Burst with Wrap instruction, all the following "Fast Read Quad I/O" and "Word Read Quad I/O" instructions will use the W6-4 setting to access the 8/16/32/64-byte section within any page. To exit the "Wrap Around" function and return to normal read operation, another Set Burst with Wrap instruction should be issued to set W4 = 1. The default value of W4 upon power on is 1. In the case of a system Reset while W4 = 0, it is recommended that the controller issues a Set Burst with Wrap instruction to reset W4 = 1 prior to any normal Read instructions since W25Q20EW does not have a hardware Reset Pin. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 0 Instruction (77h) IO0 X X X X X X w4 X IO1 X X X X X X w5 X IO2 X X X X X X w6 X IO3 X X X X X X X X don't care don't care don't care wrap bit Figure 15. Set Burst with Wrap Instruction Sequence - 29 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.13 Page Program (02h) The Page Program instruction allows from one byte to 256 bytes (a page) of data to be programmed at previously erased (FFh) memory locations. A Write Enable instruction must be executed before the device will accept the Page Program Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting the instruction code "02h" followed by a 24-bit address (A23-A0) and at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the instruction while data is being sent to the device. If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits) should be set to 0. If the last address byte is not zero, and the number of clocks exceed the remaining page length, the addressing will wrap to the beginning of the page. In some cases, less than 256 bytes (a partial page) can be programmed without having any effect on other bytes within the same page. One condition to perform a partial page program is that the number of clocks cannot exceed the remaining page length. If more than 256 bytes are sent to the device the addressing will wrap to the beginning of the page and overwrite previously sent data. As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Page Program instruction will not be executed. After /CS is driven high, the self-timed Page Program instruction will commence for a time duration of tpp (See AC Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page Program cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Page Program instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection table). Figure 17. Page Program Instruction Sequence Diagram - 30 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.14 Quad Input Page Program (32h) The Quad Page Program instruction allows up to 256 bytes of data to be programmed at previously erased (FFh) memory locations using four pins: IO0, IO1, IO2, and IO3. The Quad Page Program can improve performance for PROM Programmer and applications that have slow clock speeds <5MHz. Systems with faster clock speed will not realize much benefit for the Quad Page Program instruction since the inherent page program time is much greater than the time it take to clock-in the data. To use Quad Page Program the Quad Enable in Status Register-2 must be set (QE=1). A Write Enable instruction must be executed before the device will accept the Quad Page Program instruction (Status Register-1, WEL=1). The instruction is initiated by driving the /CS pin low then shifting the instruction code "32h" followed by a 24-bit address (A23-A0) and at least one data byte, into the IO pins. The /CS pin must be held low for the entire length of the instruction while data is being sent to the device. All other functions of Quad Page Program are identical to standard Page Program. The Quad Page Program instruction sequence is shown in figure 18. Figure 18. Quad Input Page Program Instruction Sequence Diagram - 31 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.15 Sector Erase (20h) The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "20h" followed a 24-bit sector address (A23-A0) (see Figure 2). The Sector Erase instruction sequence is shown in figure 19. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase instruction will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Sector Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection table). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 3 Mode 0 Instruction (20h) DI (IO0) DO (IO1) 9 Mode 0 24-Bit Address 23 22 2 1 0 * High Impedance * = MSB Figure 19. Sector Erase Instruction Sequence Diagram - 32 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.16 32KB Block Erase (52h) The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "52h" followed a 24-bit block address (A23-A0) (see Figure 2). The Block Erase instruction sequence is shown in figure 20. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection table). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 0 Mode 3 Mode 0 Instruction (52h) DI (IO0) DO (IO1) 9 24-Bit Address 23 22 2 1 0 * High Impedance * = MSB Figure 20. 32KB Block Erase Instruction Sequence Diagram - 33 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.17 64KB Block Erase (D8h) The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "D8h" followed a 24-bit block address (A23-A0) (see Figure 2). The Block Erase instruction sequence is shown in figure 21. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase instruction will commence for a time duration of tBE (See AC Characteristics). While the Block Erase cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Block Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be executed if the addressed page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection table). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 0 Mode 3 Mode 0 Instruction (D8h) DI (IO0) DO (IO1) 9 24-Bit Address 23 22 2 1 0 * High Impedance * = MSB Figure 21. 64KB Block Erase Instruction Sequence Diagram - 34 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.18 Chip Erase (C7h / 60h) The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Chip Erase Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "C7h" or "60h". The Chip Erase instruction sequence is shown in figure 22. The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress, the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to accept other instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Chip Erase instruction will not be executed if any page is protected by the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection table). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 0 Mode 3 Mode 0 Instruction (C7h/60h) DI (IO0) DO (IO1) High Impedance Figure 22. Chip Erase Instruction Sequence Diagram - 35 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.19 Erase / Program Suspend (75h) The Erase/Program Suspend instruction "75h", allows the system to interrupt a Sector or Block Erase operation or a Page Program operation and then read from or program/erase data to, any other sectors or blocks. The Erase/Program Suspend instruction sequence is shown in figure 23. The Write Status Register instruction (01h) and Erase instructions (20h, 52h, D8h, C7h, 60h, 44h) are not allowed during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If written during the Chip Erase operation, the Erase Suspend instruction is ignored. The Write Status Register instruction (01h) and Program instructions (02h, 32h, 42h) are not allowed during Program Suspend. Program Suspend is valid only during the Page Program or Quad Page Program operation. The Erase/Program Suspend instruction "75h" will be accepted by the device only if the SUS bit in the Status Register equals to 0 and the BUSY bit equals to 1 while a Sector or Block Erase or a Page Program operation is on-going. If the SUS bit equals to 1 or the BUSY bit equals to 0, the Suspend instruction will be ignored by the device. A maximum of time of "tSUS" (See AC Characteristics) is required to suspend the erase or program operation. The BUSY bit in the Status Register will be cleared from 1 to 0 within "tSUS" and the SUS bit in the Status Register will be set from 0 to 1 immediately after Erase/Program Suspend. For a previously resumed Erase/Program operation, it is also required that the Suspend instruction "75h" is not issued earlier than a minimum of time of "tSUS" following the preceding Resume instruction "7Ah". Unexpected power off during the Erase/Program suspend state will reset the device and release the suspend state. SUS bit in the Status Register will also reset to 0. The data within the page, sector or block that was being suspended may become corrupted. It is recommended for the user to implement system design techniques against the accidental power interruption and preserve data integrity during erase/program suspend state. Figure 23. Erase/Program Suspend Instruction Sequence - 36 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.20 Erase / Program Resume (7Ah) The Erase/Program Resume instruction "7Ah" must be written to resume the Sector or Block Erase operation or the Page Program operation after an Erase/Program Suspend. The Resume instruction "7Ah" will be accepted by the device only if the SUS bit in the Status Register equals to 1 and the BUSY bit equals to 0. After issued the SUS bit will be cleared from 1 to 0 immediately, the BUSY bit will be set from 0 to 1 within 200ns and the Sector or Block will complete the erase operation or the page will complete the program operation. If the SUS bit equals to 0 or the BUSY bit equals to 1, the Resume instruction "7Ah" will be ignored by the device. The Erase/Program Resume instruction sequence is shown in figure 24. Resume instruction is ignored if the previous Erase/Program Suspend operation was interrupted by unexpected power off. It is also required that a subsequent Erase/Program Suspend instruction not to be issued within a minimum of time of "tSUS" following a previous Resume instruction. Figure 24. Erase/Program Resume Instruction Sequence - 37 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.21 Power-down (B9h) Although the standby current during normal operation is relatively low, standby current can be further reduced with the Power-down instruction. The lower power consumption makes the Power-down instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC Characteristics). The instruction is initiated by driving the /CS pin low and shifting the instruction code "B9h" as shown in figure 25. The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-down instruction will not be executed. After /CS is driven high, the power-down state will entered within the time duration of tDP (See AC Characteristics). While in the power-down state only the Release from Power-down / Device ID instruction, which restores the device to normal operation, will be recognized. All other instructions are ignored. This includes the Read Status Register instruction, which is always available during normal operation. Ignoring all but one instruction makes the Power Down state a useful condition for securing maximum write protection. The device always powers-up in the normal operation with the standby current of ICC1. /CS tDP Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (B9h) DI (IO0) Stand-by current Power-down current Figure 25. Deep Power-down Instruction Sequence Diagram - 38 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.22 Release Power-down / Device ID (ABh) The Release from Power-down / Device ID instruction is a multi-purpose instruction. It can be used to release the device from the power-down state, or obtain the devices electronic identification (ID) number. To release the device from the power-down state, the instruction is issued by driving the /CS pin low, shifting the instruction code "ABh" and driving /CS high as shown in figure 26a. Release from powerdown will take the time duration of tRES1 (See AC Characteristics) before the device will resume normal operation and other instructions are accepted. The /CS pin must remain high during the tRES1 time duration. When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by driving the /CS pin low and shifting the instruction code "ABh" followed by 3-dummy bytes. The Device ID bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure 26a. The Device ID values for the W25Q20EW is listed in Manufacturer and Device Identification table. The Device ID can be read continuously. The instruction is completed by driving /CS high. When used to release the device from the power-down state and obtain the Device ID, the instruction is the same as previously described, and shown in figure 26b, except that after /CS is driven high it must remain high for a time duration of tRES2 (See AC Characteristics). After this time duration the device will resume normal operation and other instructions will be accepted. If the Release from Power-down / Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals 1) the instruction is ignored and will not have any effects on the current cycle. /CS tRES1 Mode 3 CLK 0 1 2 3 4 5 6 7 Mode 3 Mode 0 Mode 0 Instruction (ABh) DI (IO0) Power-down current Stand-by current Figure 26a. Release Power-down Instruction Sequence - 39 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 29 30 31 32 33 34 35 36 37 38 Mode 3 Mode 0 Mode 0 Instruction (ABh) DI (IO0) tRES2 3 Dummy Bytes 23 22 2 1 0 * Device ID High Impedance DO (IO1) 7 6 5 4 3 2 1 0 * * = MSB Power-down current Stand-by current Figure 26b. Release Power-down / Device ID Instruction Sequence Diagram - 40 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.23 Read Manufacturer / Device ID (90h) The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down / Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID. The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device ID instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code "90h" followed by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure 27. The Device ID values for the W25Q20EW is listed in Manufacturer and Device Identification table. The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is completed by driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (90h) Address (000000h) DI (IO0) 23 22 21 42 43 3 2 45 46 1 0 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 Mode 3 CLK DI (IO0) Mode 0 0 DO (IO1) 7 Manufacturer ID (EFh) * 6 5 4 3 2 1 0 Device ID Figure 27. Read Manufacturer / Device ID Diagram - 41 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.24 Read Manufacturer / Device ID Dual I/O (92h) The Manufacturer / Device ID Dual I/O instruction is an alternative to the Read Manufacturer/Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 2x speed. The Read Manufacturer / Device ID Dual I/O instruction is similar to the Fast Read Dual I/O instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code "92h" followed by a 24-bit address (A23-A0) of 000000h, but with the capability to input the Address bits two bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out 2 bits per clock on the falling edge of CLK with most significant bits (MSB) first as shown in figure 28. The Device ID values for the W25Q20EW are listed in Manufacturer and Device Identification table.The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is completed by driving /CS high. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (92h) A23-16 DI (IO0) High Impedance DO (IO1) * = MSB A15-8 A7-0 (00h) M7-0 6 4 2 0 6 4 2 0 6 4 2 0 6 4 2 0 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 * * * * /CS 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Mode 3 CLK Mode 0 IOs switch from Input to Output DI (IO0) 0 6 4 2 0 6 4 2 0 6 DO (IO1) 1 7 5 3 1 7 5 3 1 * MFR ID * Device ID 4 2 0 6 7 5 3 1 7 * MFR ID (repeat) * 4 2 0 5 3 1 Device ID (repeat) Figure 28. Read Manufacturer / Device ID Dual I/O Diagram (Bits M7-0 must be set to FFh) - 42 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.25 Read Manufacturer / Device ID Quad I/O (94h) The Read Manufacturer / Device ID Quad I/O instruction is an alternative to the Read Manufacturer / Device ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID at 4x speed. The Read Manufacturer / Device ID Quad I/O instruction is similar to the Fast Read Quad I/O instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code "94h" followed by a 24-bit address (A23-A0) of 000000h, but with the capability to input the Address bits four bits per clock. After which, the Manufacturer ID for Winbond (EFh) and the Device ID are shifted out four bits per clock on the falling edge of CLK with most significant bit (MSB) first as shown in figure 29. The Device ID values for the W25Q20EW is listed in Manufacturer and Device Identification table. The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The instruction is completed by driving /CS high. Figure 29. Read Manufacturer / Device ID Quad I/O Diagram (Bits M7-0 must be set to FFh) - 43 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.26 Read Unique ID Number (4Bh) The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique to eachW25Q20EW device. The ID number can be used in conjunction with user software methods to help prevent copying or cloning of a system. The Read Unique ID instruction is initiated by driving the /CS pin low and shifting the instruction code "4Bh" followed by a four bytes of dummy clocks. After which, the 64-bit ID is shifted out on the falling edge of CLK as shown in figure 30. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Mode 0 Instruction (4Bh) Dummy Byte 1 Dummy Byte 2 DI (IO0) High Impedance DO (IO1) 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 102 24 101 23 100 /CS Mode 3 CLK Mode 0 Dummy Byte 3 Dummy Byte 4 DI (IO0) DO (IO1) High Impedance * = MSB 63 62 61 2 1 * 64-bit Unique Serial Number 0 Figure 30. Read Unique ID Number Instruction Sequence - 44 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.27 Read JEDEC ID (9Fh) For compatibility reasons, the W25Q20EW provide several instructions to electronically determine the identity of the device. The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI compatible serial memories that was adopted in 2003. The instruction is initiated by driving the /CS pin low and shifting the instruction code "9Fh". The JEDEC assigned Manufacturer ID byte for Winbond (EFh) and two Device ID bytes, Memory Type (ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure 31. For memory type and capacity values refer to Manufacturer and Device Identification table. Figure 31. Read JEDEC ID Instruction Sequence - 45 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.28 Erase Security Registers (44h) The W25Q20EW offers three 256-byte Security Registers which can be erased and programmed individually. These registers may be used by the system manufacturers to store security and other important information separately from the main memory array. The Erase Security Register instruction is similar to the Sector Erase instruction. A Write Enable instruction must be executed before the device will accept the Erase Security Register Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code "44h" followed by a 24-bit address (A23-A0) to erase one of the three security registers. ADDRESS A23-16 A15-12 A11-8 A7-0 Security Register #0 00h 0000 0000 Don't Care Security Register #1 00h 0001 0000 Don't Care Security Register #2 00h 0010 0000 Don't Care Security Register #3 00h 0011 0000 Don't Care * Please note that Security Register 0 is Reserved by Winbond for future use. It is recommended to use Security registers 1- 3 before using register 0. The Erase Security Register instruction sequence is shown in Figure 35. The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done the instruction will not be executed. After /CS is driven high, the self-timed Erase Security Register operation will commence for a time duration of tSE (See AC Characteristics). While the Erase Security Register cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the erase cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions again. After the Erase Security Register cycle has finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Security Register Lock Bits LB[3:0] in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1, the corresponding security register will be permanently locked, Erase Security Register instruction to that register will be ignored (See 7.1.9 for detail descriptions). /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 29 30 31 Mode 3 Mode 0 Instruction (44h) DI (IO0) DO (IO1) 9 Mode 0 24-Bit Address 23 22 2 1 0 * High Impedance * = MSB Figure 35. Erase Security Registers Instruction Sequence(SPI mode only) - 46 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.29 Program Security Registers (42h) The Program Security Register instruction is similar to the Page Program instruction. It allows from one byte to 256 bytes of security register data to be programmed at previously erased (FFh) memory locations. A Write Enable instruction must be executed before the device will accept the Program Security Register Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting the instruction code "42h" followed by a 24-bit address (A23-A0) and at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the instruction while data is being sent to the device. ADDRESS A23-16 A15-12 A11-8 A7-0 Security Register #0 00h 0000 0000 Byte Address Security Register #1 00h 0001 0000 Byte Address Security Register #2 00h 0010 0000 Byte Address Security Register #3 00h 0011 0000 Byte Address * Please note that Security Register 0 is Reserved by Winbond for future use. It is recommended to use Security registers 1- 3 before using register 0. The Program Security Register instruction sequence is shown in Figure 36. The Security Register Lock Bits LB[3:0] in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is set to 1, the corresponding security register will be permanently locked, Program Security Register instruction to that register will be ignored (See 7.1.9, 7.2.21 for detail descriptions). /CS Mode 3 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 Mode 0 2 1 * 0 6 5 4 3 2 1 0 2079 3 2078 21 2077 22 2076 23 Data Byte 1 2075 24-Bit Address 2074 Instruction (42h) DI (IO0) 2073 CLK 7 * * = MSB 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 2072 /CS CLK Mode 0 Data Byte 2 DI (IO0) Mode 3 0 7 * 6 5 4 3 Data Byte 3 2 1 0 7 6 5 4 * 3 Data Byte 256 2 1 0 7 6 5 4 3 2 1 0 * Figure 36. Program Security Registers Instruction Sequence(SPI mode only) - 47 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 8.3.30 Read Security Registers (48h) The Read Security Register instruction is similar to the Fast Read instruction and allows one or more data bytes to be sequentially read from one of the three security registers. The instruction is initiated by driving the /CS pin low and then shifting the instruction code "48h" followed by a 24-bit address (A23A0) and eight "dummy" clocks into the DI pin. The code and address bits are latched on the rising edge of the CLK pin. After the address is received, the data byte of the addressed memory location will be shifted out on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The byte address is automatically incremented to the next byte address after each byte of data is shifted out. Once the byte address reaches the last byte of the register (byte FFh), it will reset to 00h, the first byte of the register, and continue to increment. The instruction is completed by driving /CS high. The Read Security Register instruction sequence is shown in Figure 37. If a Read Security Register instruction is issued while an Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any effects on the current cycle. The Read Security Register instruction allows clock rates from D.C. to a maximum of FR (see AC Electrical Characteristics). ADDRESS A23-16 A15-12 A11-8 A7-0 Security Register #0 00h 0000 0000 Byte Address Security Register #1 00h 0001 0000 Byte Address Security Register #2 00h 0010 0000 Byte Address Security Register #3 00h 0011 0000 Byte Address * Please note that Security Register 0 is Reserved by Winbond for future use. It is recommended to use Security registers 1- 3 before using register 0. /CS Mode 3 CLK 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 Mode 0 Instruction (48h) 24-Bit Address DI (IO0) 23 22 21 42 43 3 2 1 0 45 46 47 48 * High Impedance DO (IO1) * = MSB /CS 31 32 33 34 35 36 37 38 39 40 41 44 49 50 51 52 53 54 55 CLK Dummy Byte DI (IO0) 0 7 6 5 4 3 2 1 0 Data Out 1 DO (IO1) High Impedance 7 6 5 4 * 3 Data Out 2 2 1 0 7 6 5 4 3 2 1 0 7 * Figure 37. Read Security Registers Instruction Sequence(SPI mode only) - 48 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9. ELECTRICAL CHARACTERISTICS 9.1 Absolute Maximum Ratings (1) PARAMETERS SYMBOL Supply Voltage VCC Voltage Applied to Any Pin VIO Transient Voltage on any Pin VIOT Storage Temperature CONDITIONS RANGE UNIT -0.6 to 2.5V V Relative to Ground -0.6 to VCC+0.4 V <20nS Transient Relative to Ground -2.0V to VCC+2.0V V TSTG -65 to +150 C Lead Temperature TLEAD See Note (2) C Electrostatic Discharge Voltage VESD -2000 to +2000 V Human Body Model(3) Notes: 1. This device has been designed and tested for the specified operation ranges. Proper operation outside of these levels is not guaranteed. Exposure to absolute maximum ratings may affect device reliability. Exposure beyond absolute maximum ratings may cause permanent damage. 2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and the European directive on restrictions on hazardous substances (RoHS) 2002/95/EU. 3. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms). 9.2 Operating Ranges PARAMETER Supply Voltage(1) Ambient Temperature, Operating SYMBOL VCC TA CONDITIONS SPEC UNIT MIN MAX FR = 104MHz, fR = 50MHz 1.65 1.95 V Industrial -40 +85 C Note: 1. VCC voltage during Read can operate across the min and max range but should not exceed 10% of the programming (erase/write) voltage. - 49 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9.3 Power-up Timing and Write Inhibit Threshold Parameter Symbol spec MIN MAX Unit VCC (min) to /CS Low tVSL(1) 10 s Time Delay Before Write Instruction tPUW(1) 5 ms Write Inhibit Threshold Voltage VWI (1) 1.0 1.4 V Note: 1. These parameters are characterized only. 2. Initial Rest instruction must be issued. Figure 35a. Power-up Timing and Voltage Levels Figure 35b. Power-up, Power-Down Requirement - 50 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9.4 DC Electrical Characteristics: PARAMETER SYMBOL SPEC CONDITIONS MIN TYP MAX UNIT Input Capacitance CIN(1) VIN = 0V 6 pF Output Capacitance Cout(1) VOUT = 0V 8 pF Input Leakage ILI 2 A I/O Leakage ILO 2 A Standby Current ICC1 /CS = VCC, VIN = GND or VCC 10 25 A Power-down Current ICC2 /CS = VCC, VIN = GND or VCC 0.5 7.5 A Current Read 1MHz ICC3(2) C = 0.1 VCC / 0.9 VCC DO = Open 1 3 mA Current Read 50MHz ICC3(2) C = 0.1 VCC / 0.9 VCC DO = Open 4 6 mA Current Read 104MHz Icc3(2) C = 0.1 VCC / 0.9 VCC DO = Open 6 8 mA Current Write Status Register Icc4 /CS = VCC 15 20 mA Current Page Program Icc5 /CS = VCC 15 20 mA Current Sector/Block Erase Icc6 /CS = VCC 15 20 mA Current Chip Erase Icc7 /CS = VCC 15 20 mA Input Low Voltage Vil VCC x 0.3 V Input High Voltage Vih Output Low Voltage Vol Iol = 100 A Output High Voltage Voh Ioh = -100 A -0.5 VCC x 0.7 V 0.2 VCC - 0.2 V V Notes: 1. Tested on sample basis and specified through design and characterization data. TA = 25 C, VCC = 1.8V. 2. Checker Board Pattern. - 51 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9.5 AC Measurement Conditions PARAMETER SYMBOL Load Capacitance Input Rise and Fall Times Input Pulse Voltages Input Timing Reference Voltages Output Timing Reference Voltages SPEC MIN MAX UNIT CL 30 pF TR, TF 5 ns VIN 0.1 VCC to 0.9 VCC V IN 0.3 VCC to 0.7 VCC V OUT 0.5 VCC to 0.5 VCC V Note: 1. Output Hi-Z is defined as the point where data out is no longer driven. Input Levels Input and Output Timing Reference Levels 0.9 VCC 0.5 VCC 0.1 VCC Figure 36. AC Measurement I/O Waveform - 52 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9.6 AC Electrical Characteristics: SPEC DESCRIPTION SYMBOL ALT UNIT MIN Clock frequency for all instructions except for Read Data (03h) FR Clock frequency for Read Data instruction (03h) fC TYP MAX D.C. 104 MHz fR D.C. 50 MHz Clock High, Low Time for all instructions except Read Data (03h) tCLH1, tCLL1(1) 4 ns Clock High, Low Time for Read Data (03h) instruction tCRLH, tCRLL(1) 8 ns Clock Rise Time peak to peak tCLCH(2) 0.1 V/ns Clock Fall Time peak to peak tCHCL(2) 0.1 V/ns 5 ns 5 ns /CS Active Setup Time relative to CLK tSLCH /CS Not Active Hold Time relative to CLK tCHSL Data In Setup Time tDVCH tDSU 2 ns Data In Hold Time tCHDX tDH 5 ns /CS Active Hold Time relative to CLK tCHSH 5 ns /CS Not Active Setup Time relative to CLK tSHCH 5 ns /CS Deselect Time (druing Read) tSHSL1 tCSH 10 ns /CS Deselect Time (during Erase or Program or Write) tSHSL2 tCSH 50 ns Output Disable Time tSHQZ(2) tDIS 7 ns Clock Low to Output Valid tCLQV1 tV1 6 ns - 53 - tCSS Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9.7 AC Electrical Characteristics (cont'd) SPEC DESCRIPTION SYMBOL ALT UNIT MIN Output Hold Time tCLQX /HOLD Active Setup Time relative to CLK tHO TYP MAX 0 ns tHLCH 5 ns /HOLD Active Hold Time relative to CLK tCHHH 5 ns /HOLD Not Active Setup Time relative to CLK tHHCH 5 ns /HOLD Not Active Hold Time relative to CLK tCHHL 5 ns /HOLD to Output Low-Z tHHQX(2) tLZ 7 ns /HOLD to Output High-Z tHLQZ(2) tHZ 12 ns Write Protect Setup Time Before /CS Low tWHSL(3) 20 ns Write Protect Hold Time After /CS High tSHWL(3) 100 ns tDP(2) 3 s /CS High to Standby Mode without ID Read tRES1(2) 3 s /CS High to Standby Mode with ID Read tRES2(2) 1.8 s /CS High to next Instruction after Suspend tSUS(2) 20 s /CS High to Power-down Mode Write Status Register Time tW 1 15 ms Byte Program Time (First Byte) (4) tBP1 15 30 s Additional Byte Program Time (After First Byte) (4) tBP2 2.5 5 s Page Program Time tPP 0.4 0.8(5) ms Sector Erase Time (4KB) tSE 45 400 ms Block Erase Time (32KB) tBE1 150 800 ms Block Erase Time (64KB) tBE2 180 1,000 ms Chip Erase Time tce 0.5 2 s Notes: 1. Clock high + Clock low must be less than or equal to PC. PC = 1/fC. 2. Value guaranteed by design and/or characterization, not 100% tested in production. 3. Only applicable as a constraint for a Write Status Register instruction when SRP bit is set to 1. 4. 5. For multiple bytes after first byte within a page, tBPN = tBP1 + tBP2 * N (typical) and tBPN = tBP1 + tBP2 * N (max), where N = number of bytes programmed. Maximum tPP value is specified with Page Program and 4KB Sector Erase(P/E) cycling condition. - 54 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 9.8 Serial Output Timing /CS tCLH CLK tCLQV tCLQX tCLQX IO output tCLQV tCLL MSB OUT tSHQZ LSB OUT 9.9 Serial Input Timing /CS tSHSL tCHSL tSLCH tCHSH tSHCH CLK tDVCH IO input tCHDX tCLCH MSB IN tCHCL LSB IN 9.10 Hold Timing /CS tCHHL tHLCH tHHCH CLK tCHHH /HOLD tHLQZ tHHQX IO output IO input 9.11 /WP Timing /CS tWHSL tSHWL /WP CLK IO input Write Status Register is allowed - 55 - Write Status Register is not allowed Publication Release Date: July 28, 2015 -Revision D W25Q20EW 10. PACKAGE SPECIFICATION 10.1 8-Pin SOIC 150-mil (Package Code SN) 8 c 5 E HE L 1 4 0.25 D A Y e SEATING PLANE SYMBOL A A1 b C D E HE e L y GAUGE PLANE A1 b MILLIMETERS INCHES Min Nom Max Min Nom Max 1.35 0.10 0.33 0.19 4.80 3.80 5.80 1.60 0.15 0.41 0.20 4.85 3.90 6.00 1.27BSC 0.71 ----- 1.75 0.25 0.51 0.25 5.00 4.00 6.20 0.053 0.004 0.013 0.0075 0.188 0.150 0.288 0.069 0.010 0.020 0.0098 0.197 0.157 0.244 1.27 0.10 10 0.016 --- 0.062 0.006 0.016 0.0078 0.190 0.153 0.236 0.050BSC 0.027 ----- 0.40 --0 0 0.050 0.004 10 Notes: 1. Controlling dimensions: millimeters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads coplanarity with respect to seating plane shall be within 0.004 inches. - 56 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 10.2 8-Pin VSOP8 150-mil (Package Code SV) SYMBOL MILLIMETER MIN INCHES TYP. MAX MIN TYP. MAX A 0.90 0.035 A1 0.00 0.05 0.00 0.002 A2 0.8 0.031 b 0.33 0.51 0.33 0.020 c 0.125 BSC 0.005 BSC D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 1.27BSC 0.050 BSC L 0.4 0.71 1.27 0.015 0.0280 0.050 y 0.10 0.004 0 10 0 10 Notes: 1. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusions and gate burrs shall not exceed 0.15mm per side. 2. Dimension "E1" does not include inter-lead flash or protrusions. Inter-lead flash and protrusions shall not exceed 0.25mm per side. - 57 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 10.3 8-Pad USON 2x3x0.6-mm^ (Package Code UX) - 58 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 10.4 8-Ball WLCSP (Package Code BY) Symbol Min Millimeters Nom Max Min Inches Nom Max A 0.270 0.300 0.330 0.0106 0.0118 0.0130 A1 0.048 0.068 0.088 0.0019 0.0027 0.0035 c 0.222 0.232 0.242 0.0087 0.0091 0.0095 D 1.300 1.340 1.380 0.0512 0.0528 0.0543 E 1.358 1.398 1.438 0.0535 0.0550 0.0566 D1 --- 0.270 --- --- 0.0106 --- E1 --- 0.299 --- --- 0.0118 --- eD --- 0.400 --- --- 0.0157 --- eE --- 0.400 --- --- 0.0157 --- b 0.220 0.250 0.280 0.0087 0.0098 0.0110 aaa 0.100 0.0040 bbb 0.100 0.0040 ccc 0.030 0.0012 ddd 0.150 0.0060 - 59 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 11. ORDERING INFORMATION W(1) 25Q xxE W xx(2) W = Winbond 25Q = SpiFlash Serial Flash Memory with 4KB sectors, Dual/Quad I/O 20E = 2M-bit W = SN UX I = = = 1.65V to 1.95V 8-pin SOIC 150-mil 8-pad USON 2x3-mm SV = 8-pin VSOP 150-mil BY = 8-ball WLCSP Industrial (-40C to +85C) (3,4) G = E = Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3) Green Package with Extended Pad Notes: 1. The "W" prefix is not included on the part marking. 2. Only the 2nd letter is used for the part marking; WSON package type s not used for the part marking. 3. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel (shape T) or Tray (shape S), when placing orders. 4. For shipments with OTP feature enabled, please contact Winbond. - 60 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 11.1 Valid Part Numbers and Top Side Marking The following table provides the valid part numbers for the W25Q20EW SpiFlash Memory. Please contact Winbond for specific availability by density and package type. Winbond SpiFlash memories use an 12-digit Product Number for ordering. However, due to limited space, the Top Side Marking on all packages use an abbreviated 10-digit number. PACKAGE TYPE SN SOIC-8 150mil SV VSOP-8 150mil UX(1) USON-8 DENSITY PRODUCT NUMBER TOP SIDE MARKING 2M-bit W25Q20EWSNIG 25Q20EWNIG 2M-bit W25Q20EWSVIG 25Q20EWVIG 2M-bit W25Q20EWUXIE(2) 2LYww 0Exxxx(3) 2M-bit W25Q20EWBYIG 1AE . xx(4) 2x3x0.6(max.)mm BY 8-ball WLCSP Note: 1. USON package type UX is not used in the top side marking. 2. E is for extened pad 3. 2L= W25Q20EW ; Y = Year ; WW = Work Week ; xxxx = lot ID 4. XX = Date code - 61 - Publication Release Date: July 28, 2015 -Revision D W25Q20EW 12. REVISION HISTORY VERSION DATE PAGE DESCRIPTION A 04/16/2014 New Create Preliminary B 05/25/2015 Removed Preliminary C 07/09/2015 54 Removed note of 4-byte address alignment D 07/28/2015 56 Added Mom value of SOIC8-150mm Trademarks Winbond and SpiFlash are trademarks of Winbond Electronics Corporation. All other marks are the property of their respective owner. Important Notice Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales. - 62 - Publication Release Date: July 28, 2015 -Revision D