Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com Report Title: Qualification Test Report Report Type: See Attached Date: See Attached Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package HMC5445LS6 HMC5622LS7 HMC5805LS6 HMC5840LS6 HMC5846LS6 HMC5879LS7 HMC5927CLS6 HMC5927LS6 HMC5929CLS6 HMC5929LS6 HMC5981LS7 HMC6062LS6 HMC6242LS6 HMC6503LS6 HMC6741LS7 HMC6981LS6 HMC6982LS6 HMC7229LS6 QTR: 11005P Rev: 03 Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 1.0 Introduction This qualification procedure is designed to satisfy the package reliability requirements for the 20 lead 7x7mm LCC surface mount ceramic package. The testing is designed to simulate the worst-case environments the product may experience during assembly, test and life in the end user application. The device is electrically tested to the appropriate catalog specifications. The HMC5622LS7 was selected to qualify the LS LCC surface mount ceramic package family which includes the LS6, . 1.1 General Description The 20 lead 7x7mm LCC ceramic package uses a high temperature co-fired ceramic body with an epoxy sealed ceramic lid. The leads are finished with Gold over Nickel plating. The HMC5622LS 7 is a four stage GaAs pHEMT MMIC 2 Watt Power Amplifier which operates between 27.3 and 33.5 GHz. The HMC5622LS7 provides 23 dB of gain, and +34 dBm of saturated output power and 22% PAE from a +6V supply. The RF I/Os are DC blocked and matched to 50 Ohms for ease of integration into Multi-FunctionModules (MFM s). The HMC5622LS7 eliminates the need for wire bonding and allows the use of surface mount manufacturing techniques. Figure 1: Typical 20 lead 7x7mm LCC Ceramic Package Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 2.0 Summary of Results PARA TEST QTY IN QTY OUT 3.1.1 Initial Electrical Test 154 154 3.1.2 MSL3 260C Reflow Preconditioning (3 Passes) 154 154 Complete 3.1.3 Temperature Cycling 77 77 Complete 3.1.4 Post Temperature Cycle Electrical Test 77 77 Pass/No Failures 3.1.5 Autoclave 77 77 Complete 3.1.6 Post Autoclave Electrical Test 77 3.2.1 3.2.2 PASS/FAIL Pass/No Failures Pass/No Failures Pass/No Physical Dimensions 15 15 Failures Pass/No Solderability 15 15 Failures All testing has been completed. There were no failures. 77 NOTES Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 3.0 Test Procedures 3.1 Package Environmental Tests These tests are designed to demonstrate that the 20L 7x7mm Ceramic LCC surface mount family of packages are capable of maintaining the specified parameters throughout their useful life under rated operating conditions. The HMC5622LS7 was selected as the qualification vehicle to qualify the Ceramic LCC surface mount family of packages. The results of these tests qualify by similarity all other product using the same package. 3.1.1 Initial Characteristics - 154 HMC5622LS7 devices were electrically tested for DC and critical RF parameters. These tests are performed at ambient temperature (+25C). This test was performed at Hittite. There were no failures in this test. 3.1.2 MSL3 260C Reflow Preconditioning - 154 devices from 3.1.1 were subjected to 192 hours at 30C/ 60% RH then a reflow simulation at a peak temperature of 260C for 3 passes (see Figure 1 for profile). 3.1.3 Temperature Cycle - 77 devices from 3.1.2 were subjected to 500 cycles of non-operating temperature cycling from -65C to 150C. This test is performed at Hittite. 3.1.4 Final Electrical Test - 77 devices from 3.1.3 were electrically tested at ambient temperature to DC and critical RF parameters. Any out of specification parameter is considered a failure. This test was performed at Hittite. There were no failures in this test. 3.1.5 Autoclave - 77 devices from 3.1.2 were subjected to 96 hours of humidity (100%), temperature (121C) and pressure (15 PSIG). This test is performed at Hittite using an Espec environmental chamber. 3.1.6 Final Electrical Test - 77 devices from 3.1.5 were electrically tested at ambient temperature to DC and critical RF parameters. Any out of specification parameter is considered a failure. This test was performed at Hittite. There were no failures in this test. Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 3.2 Package Mechanical Tests 3.2.1 Physical Dimensions - 15 devices were measured to the requirement of the data sheet package outline drawing. These devices need not be electrically functional. Any out of specification parameter is considered a failure. This test is performed at Hittite. There were no failures. 3.2.2 Solderability - 15 devices were subjected to steam aging and solderability test in accordance with MIL-STD-883 Method 2003. These devices need not be electrically functional. This test was performed at Hittite. There were no failures. Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 Figure 2: 20 lead 6x6mm LCC Ceramic Package Outline Drawing Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package QTR: 11005P Rev: 03 Figure 3: 20 lead 7x7mm LCC Ceramic Package Outline Drawing Package Type: 20L LS7 Package Style: 20L 7x7mm Ceramic LCC Package Temperature (C) Figure 4: 260C Reflow Profile Time in Seconds QTR: 11005P Rev: 03