User's Guide SBOU110 - September 2011 LOG114EVM User Guide This user's guide describes the characteristics, operation, and use of the LOG114EVM evaluation board. It discusses how to set up and configure the board hardware, and reviews various methods of using the evaluation module (EVM). Throughout this document, the terms evaluation board, evaluation module, and EVM are synonymous with the LOG114EVM. This document also includes an electrical schematic, printed circuit board (PCB) layout drawings, and a parts list for the EVM. 1 2 3 4 5 6 Contents Overview ..................................................................................................................... 2 LOG114EVM ................................................................................................................ 3 Connecting to the LOG114EVM .......................................................................................... 7 Using the LOG114EVM ................................................................................................... 11 Verifying Results ........................................................................................................... 12 LOG114EVM Documentation ............................................................................................ 13 List of Figures ................................................................................................................ 1 LOG114EVM 2 LOG114EVM Level Shifter................................................................................................. 3 3 LOG114EVM Signal Path .................................................................................................. 4 4 High-Current Linearity Correction Circuit ................................................................................ 5 5 LOG114EVM Complete Circuit ............................................................................................ 6 6 Connecting the 5V Power Supply ......................................................................................... 7 7 Using a Photodiode with the High-Current Linearity Correction Circuitry 8 9 10 11 12 13 14 15 16 17 2 ........................................... 7 Using a Photodiode Without the High-Current Linearity Correction Circuitry ....................................... 8 Applying a 0.5-V Reverse Bias to the Photodiode...................................................................... 8 Using a Resistor to Create an Input Current ............................................................................ 9 Using a Resistor and the High Current Linearity Correction Circuitry .............................................. 10 LOG114EVM Components ............................................................................................... 11 LOG114EVM Measured Results ........................................................................................ 12 LOG114EVM Board Schematic.......................................................................................... 13 LOG114EVM: Top Side Composite Drawing .......................................................................... 14 LOG114EVM: Top Copper Layer ....................................................................................... 14 LOG114EVM: Bottom Copper Layer .................................................................................... 14 All trademarks are the property of their respective owners. SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 1 Overview 1 www.ti.com Overview The LOG114 is a single-supply, high-speed, precision logarithmic amplifier. This device computes the logarithm or log-ratio of an input current or voltage relative to a reference current or voltage. The LOG114EVM (shown in Figure 1) is a ready-to-use platform for evaluating the performance of the LOG114 in various configurations. This document gives a general overview of the LOG114EVM, and provides a general description of the features and functions to be considered while using this evaluation module. Figure 1. LOG114EVM 1.1 Getting Started Tested at the factory over a wide range of input currents, the LOG114EVM comes ready to use and includes this Quick Start User's Guide. Use of the LOG114EVM requires a 5-V power source, an input source such as a photodiode or resistor, and a digital voltmeter or oscilloscope. 1.2 Related Documentation from Texas Instruments The following documents provide information regarding Texas Instruments' integrated circuits and support tools for the LOG114EVM. This user's guide is available from the TI web site under literature number SBOU110. Any letter appended to the literature number corresponds to the document revision that is current at the time of the writing of this document. Newer revisions may be available from the TI web site, or call the Texas Instruments' Literature Response Center at (800) 477-8924 or the Product Information Center at (972) 644-5580. When ordering, identify the document by both title and literature number. Related Documentation Document 2 Literature Number LOG114 Product Data Sheet SBOS301 LOG114 TINA-TI Reference Design SBOM384B LOG114 TINA-TI Spice Model SBOM385B LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM www.ti.com 2 LOG114EVM The LOG114EVM comes completely assembled and constructed to operate on a single 5-V power supply. The circuit used in the LOG114EVM is designed to operate over a wide range of input currents (10 nA to 10 mA) and scales the output voltage from 1.15 V to 2.75 V. There are three distinct sections to the LOG114EVM circuit: a precision level shifter, the signal path, and the high-current linearity correction section. Each section is described below to familiarize you with the circuit functionality and operation. 2.1 Level Shifter A precision level shifter is required to operate the LOG114 on a single power supply. On the LOG114EVM, the level shifter circuit is constructed by deriving a bias voltage of 2 V from the 2.5-V voltage reference internal to the LOG114. This level shift of 2 V is required to keep the nodes internal to the LOG114 properly biased when operating from a single power supply. Resistors R9 and R10 form a voltage divider that is then buffered by the OPA365 amplifier. The output of the OPA365 is a fixed voltage of 2 V, independent of the power-supply voltage or input signal. C2 is used to bypass the power supply for the OPA365. The level shifter circuit is shown in Figure 2. 2.5 V from LOG114 VREF + C2 100 nF R10 1 kW R9 4.02 kW OPA365 VCC +5 V VBIAS Figure 2. LOG114EVM Level Shifter 2.2 Signal Path The LOG114 has two inputs, I1 and I2. Input I1 is used for the input signal (usually from a photodiode) and I2 is a fixed-current reference signal. This fixed-current reference signal is derived from the 2.5-V voltage reference internal to the LOG114 and the 2-V output from the level shifter. The reference current into I2 is given by Equation 1. (2.5 V - 2 V) IREF = = 500 nA 1 MW (1) The input current must flow into I1 and comes directly from the anode of a photodiode. In non-optical applications, the input current could also be derived from a resistor, or a variety of other sources (see Section 3.4). For proper operation, each input to the LOG114 (I1 and I2) requires the current to flow into the LOG114. The output from the LOG114 amplifier A3 is called VLOGOUT. The relationship between VLOGOUT, I1 and I2, and the bias voltage generated by the level shifter is described by Equation 2. I VLOGOUT = 0.375*LOG10 2 + 2 V I1 (2) ( ( SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 3 LOG114EVM www.ti.com The VLOGOUT output is then scaled by resistors R7 and R8. These resistors divide the signal before combining with the high-current linearity correction section. Combining the input signal and linearity correction signal is accomplished with amplifier A4 and resistors R5 and R6. Capacitor C1 is used to bypass the power supply for the LOG114. The signal path circuit is shown in Figure 3. High-Current Linearity Correction Signal VLOGOUT VCC 5V + R7 10 kW C1 100 nF R8 4.3 kW IREF R11 1 MW VREF R6 10 kW R5 10 kW V+ IPHOTO VREF VBIAS (from the Level Shifter) A4 A1 VOUT A3 A5 A2 V- Figure 3. LOG114EVM Signal Path 2.3 High-Current Linearity Correction The LOG114 is capable of handling a wide dynamic range of currents, from less than 100 pA in a carefully designed PCB to 10 mA in high-current applications. Because the LOG114 was designed for high speeds, the transistors that provide feedback around amplifiers A1 and A2 within the LOG114 have a small series resistance, RS. This small series resistance causes a deviation from the ideal LOG114 transfer function at input currents that exceed approximately 1 mA. The modified equation for VLOGOUT that shows this deviation from the ideal is given in Equation 3. I VLOGOUT = 0.375*LOG10 2 + 2 V + I1*RS I1 (3) ( ( 4 LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM www.ti.com The high-current linearity correction circuit (refer to Figure 4) creates an error signal that is proportional to input current I1 by using R2, R3 and R4, and amplifier A5. Resistor R1 is used to properly level-shift the resulting output signal. The signal at the output from amplifier A5 is then coupled to the input of amplifier A4 in a manner that subtracts the error signal from the output of the EVM, VOUT. VBIAS (from the Level Shifter) V+ R2 3W IPHOTO VREF A4 A1 VERR A3 A5 A2 V- R4 5 kW R3 1 kW R2 21.5 kW Figure 4. High-Current Linearity Correction Circuit SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 5 LOG114EVM www.ti.com Figure 5 shows the entire circuit layout of the LOG114EVM. VERR VLOGOUT VLOG + R7 10 kW VCC 5V R8 4.3 kW IREF R11 1 MW VREF C1 100 nF R6 10 kW R5 10 kW V+ IPHOTO R2 3W VREF A4 A1 VOUT VREF A3 C2 100 nF R10 1 kW VERR A5 A2 R9 4.02 kW OPA365 VR4 5 kW VBIAS R1 21.5 kW R3 1 kW Figure 5. LOG114EVM Complete Circuit 6 LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated SBOU110 - September 2011 Submit Documentation Feedback Connecting to the LOG114EVM www.ti.com 3 Connecting to the LOG114EVM The LOG114 requires only a few connections to operate: a 5-V power supply, an input source such as a photodiode or resistor, and a digital voltmeter or oscilloscope. 3.1 Electrostatic Discharge Warning CAUTION Many of the components on the LOG114EVM are susceptible to damage by electrostatic discharge (ESD). Customers are advised to observe proper ESD handling precautions when unpacking and handling the EVM, including the use of a grounded wrist strap at an approved ESD workstation. 3.2 Basic Connections The connections for 5 V and ground are clearly marked on the LOG114EVM PCB. Figure 6 shows how to properly connect the power supply to the connector. + +5 V Figure 6. Connecting the 5V Power Supply 3.3 Using a Photodiode An anode of a photodiode can be connected to the LOG114 by either using the pads or pin sockets on the LOG114EVM. To use the high-current linearity correction circuitry, connect the photodiode as illustrated in Figure 7. Figure 7. Using a Photodiode with the High-Current Linearity Correction Circuitry SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 7 Connecting to the LOG114EVM www.ti.com Figure 8 shows the connections required to bypass the high-current linearity circuitry. This connection results in placing zero bias across the photodiode. Figure 8. Using a Photodiode Without the High-Current Linearity Correction Circuitry A 0.5-V reverse bias can be easily placed across the photodiode by connecting the photodiode as shown in Figure 9. When connecting the photodiode in this configuration, the high-current linearity correction circuitry is bypassed. Figure 9. Applying a 0.5-V Reverse Bias to the Photodiode 8 LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated SBOU110 - September 2011 Submit Documentation Feedback Connecting to the LOG114EVM www.ti.com 3.4 Using a Resistor Using a resistor instead of a photodiode to create an input current is quite simple. As Figure 10 shows, a 1-M resistor is placed between VREF and the input I1. In this case, the input current I1 is determined by Equation 4. (V - VBIAS) I1 = REF R (4) Figure 10. Using a Resistor to Create an Input Current SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 9 Connecting to the LOG114EVM www.ti.com In the case where I1 = 500 nA = IREF, the VLOGOUT terminal is equal to the level shifting bias voltage of 2 V and the VOUT terminal is equal to 1.5 V. The circuit in Figure 10, while convenient for creating an input current, does not take advantage of the high-current linearity correction circuitry. To use this circuitry, a second power supply must be used and configured as shown in Figure 11. + + VIN Figure 11. Using a Resistor and the High Current Linearity Correction Circuitry Changing the input voltage or the resistor value changes the input current I1 (I1 = VIN/R) and results in a change for the VLOGOUT terminal voltage according to Equation 5. I VLOGOUT = 0.375*LOG10 2 + 2 V + I1*50 W I1 (5) ( ( For input currents less than 1 mA, this equation simplifies to Equation 2. The voltage at the VLOG terminal is given by Equation 6: I VLOG = [0.375*LOG10 2 + I1*50 W] * 0.3 V/V + 2 V I1 ( ( (6) The voltage at the VERR terminal is given by Equation 7: VERR = 2 + (I1*3) 2 + 1 kW 21.5 kW * 5 kW (7) The voltage at the VOUT terminal is given by Equation 8: VOUT = 2*VLOG - VERR 10 LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated (8) SBOU110 - September 2011 Submit Documentation Feedback Using the LOG114EVM www.ti.com 4 Using the LOG114EVM Once the LOG114EVM has power applied and an input signal, easy access terminal pins allow for quickly evaluating the circuit performance. Connect a digital voltmeter or oscilloscope to any of the terminals to make the measurements. Figure 12 is a reference guide to the LOG114EVM and its related components. VREF = 2.5 V VERR VOUT VLOG High Current Error Protection Input VOUT Input I1 Ground 5V Ground VBIAS = 2.0 V 5V Ground VLOGOUT Figure 12. LOG114EVM Components SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 11 Verifying Results 5 www.ti.com Verifying Results Making measurements on the LOG114EVM is fast and easy. Connect a digital voltmeter or oscilloscope to the terminal of interest and record the results. Included with the graph of measured results is a table of results for common values of input currents. In Figure 13, two curves are shown. Both curves use a resistor input and VOUT is recorded as a function of input current. The compensated (red) curve connects the resistor as shown in Figure 11 and uses the high-current linearity correction circuitry. The uncompensated curve (blue) uses the resistor connected to I1 and VREF as shown in Figure 10. 3 Output Voltage (V) Uncompensated Output Compensated Output 2.5 2 1.5 1 10n 100n 1m 10m 100m Input Current (A) 1m 10m Figure 13. LOG114EVM Measured Results Table 1 lists several typical results obtained with various input voltages. Table 1. LOG114EVM Typical Results Uncompensated 12 Compensated Input VLOGOUT (V) VOUT (V) VLOGOUT (V) VOUT (V) 10 nA 1.36 1.15 1.36 1.15 100 nA 1.74 1.38 1.74 1.38 1 A 2.11 1.60 2.11 1.60 10 A 2.49 1.83 2.49 1.83 100 A 2.87 2.06 2.87 2.06 1 mA 3.29 2.31 3.29 2.30 10 mA 4.11 2.82 4.11 2.67 LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM Documentation www.ti.com 6 LOG114EVM Documentation This section contains the complete bill of materials and PCB layout for the LOG114EVM. NOTE: These board layouts are not to scale. These image are intended to show how the board is laid out; they are not intended to be used for manufacturing LOG114EVM PCBs. 6.1 Schematic -IN5 TP7 BNC_VERT R6 10k Figure 14 shows the schematic for the LOG114EVM board TP2 VERR R4 TP3 Vout TP8 Vref Vref V+ Com Vbias R8 4.27k TP1 R1 21.3k Vcc T_STRIP2 GND T1 1 2 TP5 Vcc C7 4.7uF VCC C3 1uF TP6 GND -IN5 1k Vbias R2 R10 R9 6 1k 4.02k 5 2 D1 PIPD 4 1 6 3 R3 V ref C2 100n + VCC U2 OPA365 Vlog VCC 8 7 6 5 4 I2 3 2 1 C1 V- Vcm_IN I1 I2 100n Vo_5 -IN5 +IN5 Vo_4 -IN4 +IN4 NC Vref_GND Vlogout GND 17 U1 LOG114 I2 16 14 15 R11 1M Vbias 12 11 13 10k 9 10 R7 TP4 Vlog V ref TP9 Vlogout 5k R5 Vlog 10k 1 2 Figure 14. LOG114EVM Board Schematic SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 13 LOG114EVM Documentation 6.2 www.ti.com PCB Layout Figure 15 through Figure 17 show the PCB layout of the LOG114EVM. Figure 15. LOG114EVM: Top Side Composite Drawing Figure 16. LOG114EVM: Top Copper Layer Figure 17. LOG114EVM: Bottom Copper Layer 14 LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated SBOU110 - September 2011 Submit Documentation Feedback LOG114EVM Documentation www.ti.com 6.3 Bill of Materials Table 2 lists the bill of materials for the LOG114EVM Table 2. LOG114 Bill of Materials Item No Count Value Ref Des 1 1 21.5 k R1 Resistor, 21.5 k 1/10W 1% 0603 SMD Yageo RC0603FR-0721K5L 2 1 3 R2 Resistor, 3.0 1/10W 5% 0603 Panasonic - ECG ERJ-3GEYJ3R0V 3 2 1 k R3, R10 Resistor, 1.0 k .25W 5% 0603 SMD Vishay/Dale CRCW06031K00JNEAHP 4 1 4.99 k R4 Resistor, 4.99 k 1/10W 1% 0603 SMD Panasonic ERJ-3EKF4991V 5 3 10 k R5, R6, R7 Resistor, 10.0 k 1/10W 1% 0603 SMD Panasonic ERJ-3EKF1002VRES 6 1 4.3 k R8 Resistor, 4.3 k 1/16W .5% 0603 SMD Susumu RR0816P-432-D 7 1 4.02 k R9 Resistor, 4.02 k 1/10W 1% 0603 SMD Panasonic ERJ-3EKF4021V 8 1 1 M R11 Resistor, 1.00 M 1/10W 1% 0603 SMD Panasonic ERJ-3EKF1004V 9 1 4.7 F C7 Capacaitor, Tantalum 4.7 F 35V 10% SM AVX Corporation TAJC475K035RNJ 10 1 0.1 F C3 Capacaitor, Ceramic .100 F 25V X7R 0603 Yageo CC0603KRX7R8BB104 11 2 100 nF C1, C2 Capacaitor, Ceramic 1000 pF 25V Y5V 0603 Murata Electronics North America GRM188F51E102ZA01D 12 1 -- U1 LOG114 Texas Instruments LOG114AIRGVT 13 1 -- U2 OPA365 Texas Instruments OPA365AIDBVR 14 1 BNC TP7 Connector, Jack BNC Vert 50 Tyco Electronics 5227699-1 15 1 -- T1 PCB Terminal Block 5 MM 2-Pos On-Shore Technology ED300/2 Inc 16 9 N/A Test Points, All Connector, Header 1-Pos .100" Sgl Gold Samtec TSW-101-07-G-S 17 4 Standoff -- Standoffs, Hex , 4-40 Threaded, 0.500-in. length, 0.250-in OD, Aluminum Iridite Finish Keystone 2203 18 4 Screw -- Screw, Machine, Phillips 4-40x1/4 SS B & F Fastener Supply PMSSS 440 0025 PH 19 1 N/A D1 Do not install SBOU110 - September 2011 Submit Documentation Feedback Description MFR -- Mfr Part Number -- LOG114EVM User Guide Copyright (c) 2011, Texas Instruments Incorporated 15 Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives. Should this evaluation board/kit not meet the specifications indicated in the User's Guide, the board/kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which such TI products or services might be or are used. FCC Warning This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference. EVM Warnings and Restrictions It is important to operate this EVM within the input voltage range of 2.4V to 5.5 V and the output voltage range of 1.8 V to 4.9 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than +25C. The EVM is designed to operate properly with certain components above +25C as long as the input and output ranges are maintained. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions: The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods. Should this evaluation board/kit not meet the specifications indicated in the User's Guide, the board/kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or contact TI. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. REGULATORY COMPLIANCE INFORMATION As noted in the EVM User's Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules. For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference. General Statement for EVMs including a radio User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is the user's sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its acceptable authorization. For EVMs annotated as FCC - FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Interference Statement for Class A EVM devices This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Interference Statement for Class B EVM devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. For EVMs annotated as IC - INDUSTRY CANADA Compliant This Class A or B digital apparatus complies with Canadian ICES-003. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Concerning EVMs including radio transmitters This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Concerning EVMs including detachable antennas Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Cet appareil numerique de la classe A ou B est conforme a la norme NMB-003 du Canada. Les changements ou les modifications pas expressement approuves par la partie responsable de la conformite ont pu vider l'autorite de l'utilisateur pour actionner l'equipement. Concernant les EVMs avec appareils radio Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Concernant les EVMs avec antennes detachables Conformement a la reglementation d'Industrie Canada, le present emetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inferieur) approuve pour l'emetteur par Industrie Canada. Dans le but de reduire les risques de brouillage radioelectrique a l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnee equivalente (p.i.r.e.) ne depasse pas l'intensite necessaire a l'etablissement d'une communication satisfaisante. Le present emetteur radio a ete approuve par Industrie Canada pour fonctionner avec les types d'antenne enumeres dans le manuel d'usage et ayant un gain admissible maximal et l'impedance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est superieur au gain maximal indique, sont strictement interdits pour l'exploitation de l'emetteur. SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER Important Notice for Users of this Product in Japan This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product: 1. 2. 3. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry's Rule for Enforcement of Radio Law of Japan, Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this product, or Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan. Texas Instruments Japan Limited (address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan http://www.tij.co.jp 1. 2. 3. 61118328173 http://www.tij.co.jp SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER SPACER EVALUATION BOARD/KIT/MODULE (EVM) WARNINGS, RESTRICTIONS AND DISCLAIMERS For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end product. Your Sole Responsibility and Risk. You acknowledge, represent and agree that: 1. 2. 3. 4. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees, affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates, contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to perform as described or expected. You will take care of proper disposal and recycling of the EVM's electronic components and packing materials. Certain Instructions. It is important to operate this EVM within TI's recommended specifications and environmental considerations per the user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than 60C as long as the input and output are maintained at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development environments should use these EVMs. Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected. Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate Assurance and Indemnity Agreement. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LOG114EVM