LM1084 5A Low Dropout Positive Regulators General Description Features The LM1084 is a series of low dropout voltage positive regulators with a maximum dropout of 1.5V at 5A of load current. It has the same pin-out as National Semiconductor's industry standard LM317. The LM1084 is available in an adjustable version, which can set the output voltage with only two external resistors. It is also available in three fixed voltages: 3.3V, 5.0V and 12.0V. The fixed versions intergrate the adjust resistors. The LM1084 circuit includes a zener trimmed bandgap reference, current limiting and thermal shutdown. The LM1084 series is available in TO-220 and TO-263 packages. Refer to the LM1085 for the 3A version, and the LM1086 for the 1.5A version. n n n n n n Available in 3.3V, 5.0V, 12V and Adjustable Versions Current Limiting and Thermal Protection Output Current 5A Industrial Temperature Range -40C to 125C Line Regulation 0.015% (typical) Load Regulation 0.1% (typical) Applications n Post Regulator for Switching DC/DC Conveter n High Efficiency Linear Regulators n Battery Charger Connection Diagrams Application Circuit TO-220 10094636 Top View TO-263 10094652 1.2V to 15V Adjustable Regulator 10094635 Top View Basic Functional Diagram, Adjustable Version 10094665 (c) 2005 National Semiconductor Corporation DS100946 www.national.com LM1084 5A Low Dropout Positive Regulators June 2005 LM1084 Ordering Information Package 3-lead TO-263 3-lead TO-220 Temperature Range -40C to +125C -40C to + 125C Part Number Transport Media LM1084IS-ADJ Rails LM1084ISX-ADJ Tape and Reel LM1084IS-12 Rails LM1084ISX-12 Tape and Reel LM1084IS-3.3 Rails LM1084ISX-3.3 Tape and Reel LM1084IS-5.0 Rails LM1084ISX-5.0 Tape and Reel LM1084IT-ADJ Rails LM1084IT-12 Rails LM1084IT-3.3 Rails LM1084IT-5.0 Rails NSC Drawing TS3B T03B Simplified Schematic 10094634 www.national.com 2 Junction Temperature (TJ)(Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range 150C -65C to 150C Lead Temperature 260C, to 10 sec ESD Tolerance (Note 4) 2000V Maximum Input to Output Voltage Differential LM1084-ADJ 29V LM1084-12 18V LM1084-3.3 27V LM1084-5.0 25V Control Section -40C to 125C Internally Limited Output Section -40C to 150C Power Dissipation (Note 2) Operating Ratings (Note 1) Junction Temperature Range (TJ) (Note 3) Electrical Characteristics Typicals and limits appearing in normal type apply for TJ = 25C. Limits appearing in Boldface type apply over the entire junction temperature range for operation. Symbol VREF VOUT VOUT VOUT Parameter Reference Voltage Output Voltage (Note 7) Line Regulation (Note 8) Load Regulation (Note 8) Min (Note 6) Typ (Note 5) Max (Note 6) Units 1.238 1.225 1.250 1.250 1.262 1.270 V V LM1084-3.3 IOUT = 0mA, VIN = 8V 0 IOUT IFULL LOAD, 4.8V VIN 15V 3.270 3.235 3.300 3.300 3.330 3.365 V V LM1084-5.0 IOUT = 0mA, VIN = 8V 0 IOUT IFULL LOAD, 6.5V VIN 20V 4.950 4.900 5.000 5.000 5.050 5.100 V V LM1084-12 IOUT = 0mA, VIN = 15V 0 IOUT IFULL LOAD, 13.5V VIN 25V 11.880 11.760 12.000 12.000 12.120 12.240 V V 0.015 0.035 0.2 0.2 % % LM1084-3.3 IOUT = 0mA, 4.8V VIN 15V 0.5 1.0 6 6 mV mV LM1084-5.0 IOUT = 0mA, 6.5V VIN 20V 0.5 1.0 10 10 mV mV LM1084-12 I OUT =0mA, 13.5V VIN 25V 1.0 2.0 25 25 mV mV 0.1 0.2 0.3 0.4 % % LOAD 3 7 15 20 mV mV LOAD 5 10 20 35 mV mV 12 24 36 72 mV mV 1.3 1.5 V Conditions LM1084-ADJ IOUT = 10mA, VIN-VOUT = 3V 10mA IOUT IFULL LOAD,1.5V (VIN-VOUT) 25V (Note 7) LM1084-ADJ IOUT =10mA, 1.5V (VIN-VOUT) 15V LM1084-ADJ (VIN-V OUT) = 3V, 10mA IOUT IFULL LM1084-3.3 VIN = 5V, 0 IOUT IFULL LM1084-5.0 VIN = 8V, 0 IOUT IFULL LM1084-12 VIN = 15V, 0 IOUT IFULL Dropout Voltage (Note 9) LOAD LM1084-ADJ, 3.3, 5, 12 VREF, VOUT = 1%, IOUT = 5A 3 LOAD www.national.com LM1084 Absolute Maximum Ratings (Note 1) LM1084 Electrical Characteristics (Continued) Typicals and limits appearing in normal type apply for TJ = 25C. Limits appearing in Boldface type apply over the entire junction temperature range for operation. Symbol ILIMIT Min (Note 6) Typ (Note 5) LM1084-ADJ VIN-VOUT = 5V VIN-VOUT = 25V 5.5 0.3 8.0 0.6 A A LM1084-3.3 VIN = 8V 5.5 8.0 A LM1084-5.0 VIN = 10V 5.5 8.0 A LM1084-12 VIN = 17V 5.5 8.0 A Parameter Current Limit Conditions Max (Note 6) Units Minimum Load Current (Note 10) LM1084-ADJ VIN -VOUT = 25V 5 10.0 mA Quiescent Current LM1084-3.3 VIN = 18V 5.0 10.0 mA LM1084-5.0 VIN 20V 5.0 10.0 mA LM1084-12 VIN 25V 5.0 10.0 mA 0.003 0.015 %/W Thermal Regulation TA = 25C, 30ms Pulse Ripple Rejection fRIPPLE = 120Hz, = COUT = 25F Tantalum, IOUT = 5A LM1084-ADJ, CADJ, = 25F, (VIN-VO) = 3V 60 75 dB dB LM1084-3.3, VIN = 6.3V 60 72 LM1084-5.0, VIN = 8V 60 68 dB LM1084-12 VIN = 15V 54 60 dB Adjust Pin Current LM1084 55 120 A Adjust Pin Current Change 10mA IOUT IFULL LOAD, 1.5V VIN-VOUT 25V 0.2 5 A Temperature Stability 0.5 Long Term Stability TA =125C, 1000Hrs RMS Output Noise (% of VOUT) 10Hz f 10kHz Thermal Resistance Junction-to-Case 3-Lead TO-263: Control Section/Output Section 3-Lead TO-220: Control Section/Output Section 0.3 % 1.0 0.003 % % 0.65/2.7 0.65/2.7 C/W C/W Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Power dissipation is kept in a safe range by current limiting circuitry. Refer to Overload Recovery in Application Notes. Note 3: The maximum power dissipation is a function of TJ(max) , JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max)-T A)/JA. All numbers apply for packages soldered directly into a PC board. Refer to Thermal Considerations in the Application Notes. Note 4: For testing purposes, ESD was applied using human body model, 1.5k in series with 100pF. Note 5: Typical Values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: IFULLLOAD is defined in the current limit curves. The IFULLLOAD Curve defines the current limit as a function of input-to-output voltage. Note that 30W power dissipation for the LM1084 is only achievable over a limited range of input-to-output voltage. Note 8: Load and line regulation are measured at constant junction temperature, and are guaranteed up to the maximum power dissipation of 30W. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note 9: Dropout voltage is specified over the full output current range of the device. Note 10: The minimum output current required to maintain regulation. www.national.com 4 LM1084 Typical Performance Characteristics Dropout Voltage (VIN-VOUT) Short-Circuit Current 10094671 10094663 Load Regulation LM1084-ADJ Ripple Rejection 10094638 10094643 LM1084-ADJ Ripple Rejection vs Current Temperature Stability 10094690 10094625 5 www.national.com LM1084 Typical Performance Characteristics (Continued) Adjust Pin Current LM1084-ADJ Load Transient Response 10094669 10094626 LM1084-ADJ LineTransient Response Maximum Power Dissipation 10094668 10094670 www.national.com 6 Stability consideration primarily concern the phase response of the feedback loop. In order for stable operation, the loop must maintain negative feedback. The LM1084 requires a certain amount series resistance with capacitive loads. This series resistance introduces a zero within the loop to increase phase margin and thus increase stability. The equivalent series resistance (ESR) of solid tantalum or aluminum electrolytic capacitors is used to provide the appropriate zero (approximately 500 kHz). The Aluminum electrolytic are less expensive than tantalums, but their ESR varies exponentially at cold temperatures; therefore requiring close examination when choosing the desired transient response over temperature. Tantalums are a convenient choice because their ESR varies less than 2:1 over temperature. GENERAL Figure 1 shows a basic functional diagram for the LM1084Adj (excluding protection circuitry) . The topology is basically that of the LM317 except for the pass transistor. Instead of a Darlingtion NPN with its two diode voltage drop, the LM1084 uses a single NPN. This results in a lower dropout voltage. The structure of the pass transistor is also known as a quasi LDO. The advantage a quasi LDO over a PNP LDO is its inherently lower quiescent current. The LM1084 is guaranteed to provide a minimum dropout voltage 1.5V over temperature, at full load. The recommended load/decoupling capacitance is a 10uF tantalum or a 50uF aluminum. These values will assure stability for the majority of applications. The adjustable versions allows an additional capacitor to be used at the ADJ pin to increase ripple rejection. If this is done the output capacitor should be increased to 22uF for tantalums or to 150uF for aluminum. Capacitors other than tantalum or aluminum can be used at the adjust pin and the input pin. A 10uF capacitor is a reasonable value at the input. See Ripple Rejection section regarding the value for the adjust pin capacitor. It is desirable to have large output capacitance for applications that entail large changes in load current (microprocessors for example). The higher the capacitance, the larger the available charge per demand. It is also desirable to provide low ESR to reduce the change in output voltage: V = I x ESR It is common practice to use several tantalum and ceramic capacitors in parallel to reduce this change in the output voltage by reducing the overall ESR. Output capacitance can be increased indefinitely to improve transient response and stability. 10094665 FIGURE 1. Basic Functional Diagram for the LM1084, excluding Protection circuitry OUTPUT VOLTAGE The LM1084 adjustable version develops at 1.25V reference voltage, (VREF), between the output and the adjust terminal. As shown in figure 2, this voltage is applied across resistor R1 to generate a constant current I1. This constant current then flows through R2. The resulting voltage drop across R2 adds to the reference voltage to sets the desired output voltage. The current IADJ from the adjustment terminal introduces an output error . But since it is small (120uA max), it becomes negligible when R1 is in the 100 range. For fixed voltage devices, R1 and R2 are integrated inside the devices. RIPPLE REJECTION Ripple rejection is a function of the open loop gain within the feed-back loop (refer to Figure 1 and Figure 2). The LM1084 exhibits 75dB of ripple rejection (typ.). When adjusted for voltages higher than VREF, the ripple rejection decreases as function of adjustment gain: (1+R1/R2) or VO/VREF. Therefore a 5V adjustment decreases ripple rejection by a factor of four (-12dB); Output ripple increases as adjustment voltage increases. However, the adjustable version allows this degradation of ripple rejection to be compensated. The adjust terminal can be bypassed to ground with a capacitor (CADJ). The impedance of the CADJ should be equal to or less than R1 at the desired ripple frequency. This bypass capacitor prevents ripple from being amplified as the output voltage is increased. 1/(2*fRIPPLE*CADJ) R1 LOAD REGULATION The LM1084 regulates the voltage that appears between its output and ground pins, or between its output and adjust pins. In some cases, line resistances can introduce errors to the voltage across the load. To obtain the best load regulation, a few precautions are needed. 10094617 FIGURE 2. Basic Adjustable Regulator 7 www.national.com LM1084 STABILITY CONSIDERATION Application Note LM1084 Application Note adjustment terminal. The adjust pin can take a transient signal of 25V with respect to the output voltage without damaging the device. (Continued) Figure 3 shows a typical application using a fixed output regulator. Rt1 and Rt2 are the line resistances. VLOAD is less than the VOUT by the sum of the voltage drops along the line resistances. In this case, the load regulation seen at the RLOAD would be degraded from the data sheet specification. To improve this, the load should be tied directly to the output terminal on the positive side and directly tied to the ground terminal on the negative side. When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage of the regulator, and rate of decrease of VIN. In the LM1084 regulator, the internal diode between the output and input pins can withstand microsecond surge currents of 10A to 20A. With an extremely large output capacitor (1000 f), and with input instantaneously shorted to ground, the regulator could be damaged. In this case, an external diode is recommended between the output and input pins to protect the regulator, shown in Figure 5. 10094618 FIGURE 3. Typical Application using Fixed Output Regulator When the adjustable regulator is used (Figure 4), the best performance is obtained with the positive side of the resistor R1 tied directly to the output terminal of the regulator rather than near the load. This eliminates line drops from appearing effectively in series with the reference and degrading regulation. For example, a 5V regulator with 0.05 resistance between the regulator and load will have a load regulation due to line resistance of 0.05 x IL. If R1 (=125) is connected near the load the effective line resistance will be 0.05 (1 + R2/R1) or in this case, it is 4 times worse. In addition, the ground side of the resistor R2 can be returned near the ground of the load to provide remote ground sensing and improve load regulation. 10094615 FIGURE 5. Regulator with Protection Diode OVERLOAD RECOVERY Overload recovery refers to regulator's ability to recover from a short circuited output. A key factor in the recovery process is the current limiting used to protect the output from drawing too much power. The current limiting circuit reduces the output current as the input to output differential increases. Refer to short circuit curve in the curve section. During normal start-up, the input to output differential is small since the output follows the input. But, if the output is shorted, then the recovery involves a large input to output differential. Sometimes during this condition the current limiting circuit is slow in recovering. If the limited current is too low to develop a voltage at the output, the voltage will stabilize at a lower level. Under these conditions it may be necessary to recycle the power of the regulator in order to get the smaller differential voltage and thus adequate start up conditions. Refer to curve section for the short circuit current vs. input differential voltage. 10094619 THERMAL CONSIDERATIONS ICs heats up when in operation, and power consumption is one factor in how hot it gets. The other factor is how well the heat is dissipated. Heat dissipation is predictable by knowing the thermal resistance between the IC and ambient (JA). Thermal resistance has units of temperature per power (C/ W). The higher the thermal resistance, the hotter the IC. The LM1084 specifies the thermal resistance for each package as junction to case (JC). In order to get the total resistance to ambient (JA), two other thermal resistance FIGURE 4. Best Load Regulation using Adjustable Output Regulator PROTECTION DIODES Under normal operation, the LM1084 regulator does not need any protection diode. With the adjustable device, the internal resistance between the adjustment and output terminals limits the current. No diode is needed to divert the current around the regulator even with a capacitor on the www.national.com 8 IIN = IL + IG PD = (VIN-VOUT) IL + VINIG Figure 6 shows the voltages and currents which are present in the circuit. (Continued) must be added, one for case to heat-sink (CH) and one for heatsink to ambient (HA). The junction temperature can be predicted as follows: TJ = TA + PD (JC + CH + HA) = TA + PD JA TJ is junction temperature, TA is ambient temperature, and PD is the power consumption of the device. Device power consumption is calculated as follows: 10094616 FIGURE 6. Power Dissipation Diagram HA (max) = JA (max) - (JC + CH) (HA (max)) should also be calculated twice as follows: (HA (max)) = JA (max, CONTROL SECTION) - (JC (CONTROL SECTION) + CH) (HA (max)) = JA(max, OUTPUT SECTION) - (JC (OUTPUT SECTION) + CH) If thermal compound is used, CH can be estimated at 0.2 C/W. If the case is soldered to the heat sink, then a CH can be estimated as 0 C/W. After, HA (max) is calculated for each section, choose the lower of the two HA (max) values to determine the appropriate heat sink. Once the devices power is determined, the maximum allowable (JA (max)) is calculated as: JA (max) = TR(max)/PD = TJ(max) - TA(max)/PD The LM1084 has different temperature specifications for two different sections of the IC: the control section and the output section. The Electrical Characteristics table shows the junction to case thermal resistances for each of these sections, while the maximum junction temperatures (TJ(max)) for each section is listed in the Absolute Maximum section of the datasheet. TJ(max) is 125C for the control section, while TJ(max) is 150C for the output section. JA (max) should be calculated separately for each section as follows: JA (max, CONTROL SECTION) = (125C - TA(max))/PD JA (max, OUTPUT SECTION) = (150C - TA(max))/PD The required heat sink is determined by calculating its required thermal resistance (HA (max)). If PC board copper is going to be used as a heat sink, then Figure 7 can be used to determine the appropriate area (size) of copper foil required. 10094664 FIGURE 7. Heat sink thermal Resistance vs Area 9 www.national.com LM1084 Application Note LM1084 Typical Applications 10094667 5V to 3.3V, 5A Regulator 10094654 Battery Charger 10094650 10094655 Adjustable @ 5V Adjustable Fixed Regulator 10094656 Regulator with Reference 10094652 1.2V to 15V Adjustable Regulator 10094657 High Current Lamp Driver Protection 10094653 5V Regulator with Shutdown www.national.com 10 LM1084 Typical Applications (Continued) 10094661 Automatic Light control 10094659 Battery Backup Regulated Supply 10094662 Generating Negative Supply voltage 10094660 Ripple Rejection Enhancement 10094658 Remote Sensing 11 www.national.com LM1084 Physical Dimensions inches (millimeters) unless otherwise noted 3-Lead TO-263 NS Package Number TS3B 3-Lead TO-220 NS Package Number T03B www.national.com 12 LM1084 5A Low Dropout Positive Regulators Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560