ISL90461 (R) Digitally Controlled Potentiometer (XDCPTM) Data Sheet June 6, 2005 FN8229.2 Single Volatile 32-Tap XDCP Features The Intersil ISL90461 is a digitally controlled potentiometer (XDCP). Configured as a variable resistor, the device consists of a resistor array, wiper switches, a control section, and volatile memory. The wiper position is controlled by a 2pin Up /Down interface. * Volatile solid-state potentiometer The potentiometer is implemented by a resistor array composed of 31 resistive elements and a wiper switching network. Between each element and at either end are tap points accessible to the wiper terminal. The position of the wiper element is controlled by the CS and U/D inputs. * 32 wiper tap points The device can be used in a wide variety of applications including: * Available RTOTAL values = 10k, 50k, 100k * LCD contrast control * 2-pin UP/DN interface * DCP terminal voltage, 2.7V to 5.5V * Tempco 35 ppm/C typical * Low power CMOS - Active current, 25A max. - Supply current 0.3A * Temperature Range -40C to +85C * Parameter and bias adjustments * Packages - 6 Ld SC70, SOT23 * Industrial and Automotive Control * Pb-Free Plus Anneal Available (RoHS Compliant) * Transducer adjustment of pressure, temperature, position, chemical, and optical sensors Pinout ISL90461 (SOT23, SC70) TOP VIEW * Laser Diode driver biasing * Gain control and offset adjustment Ordering Information RTOTAL PACKAGE TEMP RANGE (C) ISL90461TIE627 100K SC70 -40 to +85 ISL90461TIE627Z (See Note) 100K SC70 (Pb-free) -40 to +85 ISL90461UIE627 50K SC70 -40 to +85 ISL90461UIE627Z (See Note) 50K SC70 (Pb-free) -40 to +85 ISL90461WIE627 10K SC70 -40 to +85 ISL90461WIE627Z (See Note) 10K SC70 (Pb-free) -40 to +85 ISL90461TIH627 100K SOT-23 -40 to +85 ISL90461TIH627Z (See Note) 100K SOT-23 (Pb-free) -40 to +85 ISL90461UIH627 50K SOT-23 -40 to +85 ISL90461UIH627Z (See Note) 50K SOT-23 (Pb-free) -40 to +85 PART NUMBER ISL90461WIH627 10K SOT-23 -40 to +85 ISL90461WIH627Z (See Note) 10K SOT-23 (Pb-free) -40 to +85 VDD RH GND RL U/D CS Add "-TK" suffix for tape and reel. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL90461 Block Diagram VCC RH UP/DOWN (U/D) CONTROL AND MEMORY DEVICE SELECT (CS) RL GND (GROUND) GENERAL Pin Descriptions 6-PIN SYMBOL DESCRIPTION 1 VDD Supply voltage 2 GND Ground 3 U/D Up - Down 4 CS Chip select 5 RL Low terminal 6 RH High terminal/ Wiper terminal 2 FN8229.2 June 6, 2005 ISL90461 Absolute Maximum Ratings Recommended Operating Conditions Storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Voltage on CS, U/D and VCC with respect to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V Lead temperature (soldering 10s) . . . . . . . . . . . . . . . . . . . . . . 300C IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6mA Power rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1mW Temperature Range (Industrial) . . . . . . . . . . . . . . . . .-40C to +85C Supply Voltage (VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Potentiometer Specifications Over recommended operating conditions unless otherwise stated. SYMBOL RTOT VR PARAMETER MIN TYP (Note 4) MAX UNIT W version 8 10 12 k U version 40 50 60 k T version 80 100 120 k VCC V TEST CONDITIONS/NOTES End to end resistance RH, RL terminal voltages 0 Noise Ref: 1kHz RW Wiper Resistance IW Wiper Current dBV 600 0.6 Resolution 32 Absolute linearity (Note 1) RH(n)(actual)-RH(n)(expected) Relative linearity (Note 2) RH(n+1)-[RH(n)+MI] RTOTAL temperature coefficient CH/CL/CW -120 Potentiometer capacitances See circuit #3 mA Taps 1 MI (Note 3) 0.5 MI (Note 3) 35 ppm/C 10/10/25 pF NOTES: 1. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage = (RH(n)(actual)-RH(n)(expected)) = 1 Ml Maximum. n = 1 .. 29 only 2. Relative linearity is a measure of the error in step size between taps = RH(n+1)--[RH(n) + Ml] = 0.5 Ml, n = 1 .. 29 only. 3. 1 Ml = Minimum Increment = RTOT/31. 4. Typical values are for TA = 25C and nominal supply voltage. DC Electrical Specifications SYMBOL Over recommended operating conditions unless otherwise specified. PARAMETER TEST CONDITIONS ICC VCC active current (Increment) CS = 0V, U/D = fclock = 1MHz and VCC = 3V ISB Standby supply current CS = VCC, U/D = GND or VCC = 3V ILI CS input leakage current VIN = GND to VCC VIH CS, U/D input HIGH voltage VIL CS, U/D input LOW voltage CIN CS, U/D input capacitance 3 MIN TYP (Note 4) 0.3 MAX UNIT 25 A 1 A 1 A VCC x 0.7 V VCC x 0.3 VCC = 3V, VIN = VSS, TA = 25C, f = 1MHz 10 V pF FN8229.2 June 6, 2005 ISL90461 Timing Specifications (Over recommended operating conditions unless otherwise specified) SYMBOL PARAMETER MIN TYP (Note 4) MAX UNIT tCU U/D to CS setup 25 ns tCI CS to U/D setup 50 ns tIC CS to U/D hold 25 ns tlL U/D LOW period 300 ns tlH U/D HIGH period 300 ns fTOGGLE Up/Down toggle Rate 1 MHz tSETTLE Output settling time 1 s CS tCU tIC tIL U/D tSETTLE tIH tCI RH - RL FIGURE 1. SERIAL INTERFACE TIMING DIAGRAM, INCREMENT CS tCU tIC tIH U/D tCI tIL tSETTLE RH - RL FIGURE 2. SERIAL INTERFACE TIMING DIAGRAM, DECREMENT 4 FN8229.2 June 6, 2005 ISL90461 Pin Descriptions Principles of Operation RH and RL There are two sections of the ISL90461: the input control, counter and decode section; and the resistor array. The input control section operates just like an up/down counter. The output of this counter is decoded to turn on a single electronic switch connecting a point on the resistor array to the wiper output. The resistor array is comprised of 31 individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the connection at that point to the wiper. The wiper is connected to the RH terminal, forming a variable resistor from RH to RL. The ISL90461 contains a digital potentiometer configured as a variable resistor. The wiper of the potentiometer is tied to one end of the potentiometer at terminal RH, and the RL pin is the other terminal of the potentiometer. The resistance from the RH pin to the RL pin will vary with the potentiometer setting. At the highest setting the resistance will be maximum (Rtot) and at the lowest setting it will be minimum. As the wiper position is incremented, the wiper will move from the Low terminal to the High terminal. Up/Down (U/D) The U/D input controls the direction of the wiper movement and whether the counter is incremented or decremented. Chip Select (CS) The device is selected when the CS input is LOW. The current counter value is stored in volatile memory when CS is returned HIGH. When CS is high, the device is placed in low power standby mode. 5 The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. That is, the counter does not wrap around when clocked to either extreme. If the wiper is moved several positions, multiple taps are connected to the wiper for tIW (U/D to VW change). The 2-terminal resistance value for the device can temporarily change by a significant amount if the wiper is moved several positions. FN8229.2 June 6, 2005 ISL90461 Small Outline Transistor Plastic Packages (SC70-6) 0.20 (0.008) M SC70-6 VIEW C C 6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE CL INCHES e b 6 5 4 CL CL E1 E 1 2 3 e1 C D CL A A2 SEATING PLANE A1 -C- SYMBOL MIN MAX MIN MAX NOTES A 0.031 0.043 0.80 1.10 - A1 0.000 0.004 0.00 0.10 - A2 0.031 0.039 0.00 1.00 - b 0.006 0.012 0.15 0.30 b1 0.006 0.010 0.15 0.25 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.009 0.08 0.20 6 D 0.071 0.087 1.80 2.20 3 E 0.071 0.094 1.80 2.40 - E1 0.045 0.053 1.15 1.35 3 e e1 L 0.10 (0.004) C WITH b PLATING b1 0.0256 Ref c1 0.65 Ref 0.0512 Ref 0.010 0.018 - 1.30 Ref 0.26 - 0.46 L1 0.017 Ref. 0.420 Ref. L2 0.006 BSC 0.15 BSC N c MILLIMETERS 6 4 6 5 R 0.004 - 0.10 - R1 0.004 0.010 0.15 0.25 0 8 0 8 - NOTES: BASE METAL 1. Dimensioning and tolerance per ASME Y14.5M-1994. 2. Package conforms to EIAJ SC70 and JEDEC MO203AB. 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. 4X 1 4. Footlength L measured at reference to gauge plane. R1 5. "N" is the number of terminal positions. R GAUGE PLANE SEATING PLANE L C L1 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only. L2 4X 1 VIEW C 6 FN8229.2 June 6, 2005 ISL90461 Small Outline Transistor Plastic Packages (SOT23-6) 0.20 (0.008) M P6.064 VIEW C C 6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE CL INCHES e b SYMBOL 6 5 4 CL CL E1 E 1 2 3 e1 C D CL A A2 SEATING PLANE A1 -C- WITH b PLATING b1 c c1 MILLIMETERS MAX MIN MAX NOTES A 0.036 0.057 0.90 1.45 - A1 0.000 0.0059 0.00 0.15 - A2 0.036 0.051 0.90 1.30 - b 0.012 0.020 0.30 0.50 - b1 0.012 0.018 0.30 0.45 c 0.003 0.009 0.08 0.22 6 c1 0.003 0.008 0.08 0.20 6 D 0.111 0.118 2.80 3.00 3 E 0.103 0.118 2.60 E1 0.060 0.068 1.50 3.00 - 1.75 3 e 0.0374 Ref 0.95 Ref - e1 0.0748 Ref 1.90 Ref - L 0.10 (0.004) C MIN 0.014 0.022 0.35 0.55 L1 0.024 Ref. 0.60 Ref. L2 0.010 Ref. 0.25 Ref. N 6 6 4 5 R 0.004 - 0.10 - R1 0.004 0.010 0.10 0.25 0o 8o 0o 8o Rev. 3 9/03 BASE METAL NOTES: 1. Dimensioning and tolerance per ASME Y14.5M-1994. 4X 1 2. Package conforms to EIAJ SC-74 and JEDEC MO178AB. 3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs. R1 4. Footlength L measured at reference to gauge plane. R 5. "N" is the number of terminal positions. GAUGE PLANE SEATING PLANE L C L1 L2 6. These Dimensions apply to the flat section of the lead between 0.08mm and 0.15mm from the lead tip. 7. Controlling dimension: MILLIMETER. Converted inch dimensions are for reference only 4X 1 VIEW C All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 7 FN8229.2 June 6, 2005