version 2013-05 EC/AC centrifugal fans - RadiCal The engineer's choice EC/AC centrifugal fans - RadiCal Impellers made of high-tech compound material with optimised flow con- This opens up entirely new possibilities for applications in ventilation and trol, combined with proven single- or 3-phase asynchronous motors or air-conditioning and beyond. For example, ebm-papst AC fans can now be highly efficient GreenTech EC motors: these are the outstanding features replaced by the latest fans in GreenTech EC technology without any of the new generation of backward-curved centrifugal fans for operation expensive modification. without scroll housing. That's RadiCal! Advantages at a glance: The impellers in sizes 133 to 630mm are made of a single-piece special - High efficiency with improved impeller technology and new EC motors compound material which allows for high rotational speed, and thus for - Perfectly matching components (controller/motor/impeller) the high power density of the fan. The impeller styling has been optimised - Extremely quietly running with optimised air flow through the impeller using complex simulation models adjusted to perfection by checking - Significantly reduced tonal noise against prototypes. The result is an optimal, low-loss flow of air through - Unrivalled compactness the impeller and so there are no longer any drastic cross-sectional chan- - Mechanical compatibility of AC and EC fans ges, a well-known source of losses in the impeller. A uniform flow profile - EC fans with 2 speeds or continuous control without separations also means fewer noise sources and thus better - High power density acoustics. That's RadiCal, too! - Robust design and maintenance-free operation - Easy initial set-up The new motor in GreenTech EC technology with integrated control elec- - ErP* compliant (see individual designation) tronics is designed in such as way as to make the RadiCal fans in sizes 190 up to 250mm have the same mounting dimensions as the combina- *ErP: Energy-related Products directive - defined minimum requirements tion of the same impeller with an asynchronous motor. In addition, the for fans in accordance with the EcoDesign directive for fans with a specified EC centrifugal fan achieves significantly higher air performance drive output of 125 W and above. than the AC variant with identical dimensions. The small GreenTech EC fans are available in two different control configurations: one with two fixed speed stages and another with the familiar continuous control option via a combined 0-10V/PWM control input. Sizes exceeding 250mm can be controlled by a 0-10V/PWM input signal or monitored respectively controlled via RS485 serial connection, using the MODBUS-RTU protocol. 2 Table of contents EC/AC centrifugal fans - RadiCal 2 GreenTech: The Green Company 4 EC centrifugal fans - RadiCal O 133-630 7 AC centrifugal fans - RadiCal O 133-630 101 Accessories 158 Electrical connections 163 Technical parameters & scope 172 ebm-papst representatives & subsidiaries 176 3 Sustainability is at the centre of our thoughts and actions. Out of conviction! Philosophy Eco-friendliness and sustainability have always been at the core of Development our thoughts and actions. For decades, we have worked according to the simple but strict creed of our co-founder Gerhard Sturm: Application "Each new product we develop has to be better than the last one in Production terms of economy and ecology." GreenTech is the ultimate expression of our corporate philosophy. Awards GreenTech is pro-active development. GreenTech is acknowledged and certified. Even in the design phase, the materials and processes we use are optimi- Every step in our chain of production meets the stringent standards of sed for the greatest possible eco-friendliness, energy balance and - environmental specialists and the public. The Deutscher Nachhaltigkeits- wherever possible - recyclability. We continually improve the material preis 2012 (German Sustainability Award 2012), where we were given the and performance of our products, as well as the flow and noise charac- Top3-award in the category "Germany's most sustainable strategy for the teristics. At the same time, we significantly reduce energy consumption. future (company group)" bears testimony to our commitment to sustainabi- Close co-operation with universities and scientific institutes and the pro- lity, as does the DEKRA Award 2012 we received in the category "Umwelt - fessorship we endow in the area of power engineering and regenerative Herausforderung Energiewende / Environment - Challenge: Transition to energies allows us to profit from the latest research findings in these more sustainable energy systems", to name only a few of a large number fields - and at the same time ensure highly qualified young academics. of examples. The environmental advantage gained in the performance of the products developed from our GreenTech philosophy can also be mea- GreenTech is eco-friendly production. sured in the fulfillment of the most stringent energy and environmental GreenTech also stands for maximum energy efficiency in our production standards. In many instances, our products are already well below the processes. There, the intelligent use of industrial waste heat and ground- thresholds energy legislation will impose a few years from now - several water cooling, photovoltaics and, of course, our own cooling and venti- times over. lation technology are of the utmost importance. Our most modern plant, for instance, consumes 91% less energy than currently specified and Our customers profit from this every day. required. In this way, our products contribute to protecting the environ- The heart of GreenTech is future-oriented EC technology from ebm- ment, from their origin to their recyclable packaging. papst. The EC technology at the core of our most efficient motors and fans allows efficiency of up to 90%, saves energy at a very high level, significantly extends service life and makes our products maintenancefree. These values pay off not only for the environment, but every cent also pays off for the user! All ebm-papst products - even those for which GreenTech EC technology does not (yet) make sense from an application viewpoint - feature the greatest possible connection of economy and ecology. 4 5 6 EC centrifugal fans - RadiCal 7 EC centrifugal fans - RadiCal backward curved, O 133 Hz rpm W A C 50/60 3770 27 0,27 -25..+60 1~ 200-240 Pa in H2O 3 p. 165 / H4) 1,4 360 max. = 1,6 A 400 320 1,2 4 160 0,8 200 3 0,6 240 1,0 280 120 0,4 2 40 0,2 80 pfs 1 0 qV 20 40 40 60 80 80 120 100 160 120 200 140 240 160 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 8 Technical features and electrical connection VAC (1) Nominal data in operating point with maximum load and 230 VAC subject to alterations Curves: Speed-controlled A Perm. amb. temp. M3G 045-AI Max. current draw(1) *3G 133 Max. input power(1) Motor Speed/rpm(1) Type Frequency Nominal data Nominal voltage range Curve - Material: Housing: PA plastic 6, fibreglass-reinforced Impeller: PA plastic 6, fibreglass-reinforced Rotor: Thick layer passivated Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None, open rotor - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings n rpm Ped W I A LWA dB(A) A 1 3930 24 0,23 66 A 2 3800 26 0,26 63 A 3 3770 27 0,27 61 A 4 3835 26 0,25 65 Mass of centrifugal fan Mass of centrifugal module with support basket - Technical features: See electrical connections p. 165 - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support basket kg R3G 133-RA01 -03 0,5 K3G 133-RA01 -03 0,75 Drawings p. 10 Inlet nozzle p. 158 Guard grille p. 160 Electr. connection p. 165 9 EC centrifugal fans - RadiCal backward curved, O 133, speed-controlled R3G 133-RA01-03 (Centrifugal fan) O4.5 (4x) 631 57.3 Accessory part: Inlet nozzle 09566-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm 4x9 M4 (4x) 0 10 85 450 +20 O580.2 O118 O129 O87 O133 O930.2 O27 O89 2 1 48.5 6 13 4 Control line AWG 22, 4 x brass lead tips crimped Connection line AWG 20, 3 x brass lead tips crimped K3G 133-RA01-03 (Centrifugal module with support basket) o165 O5 (4x) 2 64 o1470.5 6 45 O1 80 0 .5 50 O19 .5 O27 Mounting dimensions: O2 O1 10 95 0.5 20 0+ 45 6 10 10 85 11 EC centrifugal fans - RadiCal backward curved, O 190 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 2710 57 0,43 -25..+60 p. 164 / H3) B 1~ 200-240 50/60 4120 169 1,35 -25..+60 p. 164 / H3) M3G 055-BI C 1~ 200-240 50/60 3200 83 0,75 -25..+60 p. 165 / H4) *3G 190 M3G 055-CF D 1~ 200-240 50/60 3640 115 1,10 -25..+60 p. 163 / H5) *3G 190 M3G 055-CF E 1~ 200-240 50/60 4120 169 1,35 -25..+60 p. 165 / H4) Curve Nominal voltage range Technical features and electrical connection - Material: Housing: PA plastic 6, fibreglass-reinforced Impeller: PA plastic 6, fibreglass-reinforced Rotor: Thick layer passivated Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None, open rotor - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 190 M3G 055-BD A *3G 190 M3G 055-CF *3G 190 Pa 1000 800 n rpm max. = 7 4,0 3 3,2 Curves: 2 Speed stages (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations B 600 2,4 4 8 400 1,6 3 7 A 4 0,8 200 3 6 7 2 6 pfs 5 0 qV 100 200 200 400 5 1 300 400 600 1 500 800 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 12 I A LWA dB(A) A 1 2880 49 0,36 69 A 2 2815 52 0,40 64 A 3 2710 57 0,43 62 A 4 2780 54 0,41 67 A 5 2435 30 0,23 65 A 6 2390 32 0,25 60 A 7 2325 35 0,27 59 A 8 2360 33 0,26 63 B 1 4440 160 1,35 81 B 2 4235 165 1,35 75 B 3 4120 169 1,35 72 B 4 4155 160 1,35 74 B 5 3720 95 0,85 77 B 6 3675 105 0,95 73 B 7 3615 115 1,00 69 B 8 3650 110 0,95 72 2 8 Ped W Mass of centrifugal fan Mass of centrifugal module with support basket - Technical features: See electrical connections p. 163 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for kg R3G 190-RB01 -01 0,85 K3G 190-RB01 -01 1,40 R3G 190-RD45 -01 1,36 K3G 190-RD45 -01 1,91 R3G 190-RC05 -03 1,06 K3G 190-RC05 -03 1,61 R3G 190-RG19 -01 1,40 K3G 190-RG19 -01 1,60 R3G 190-RD45 -03 1,36 K3G 190-RD45 -03 1,91 4,0 1000 n rpm max. = 3 800 3,2 E D 600 2,4 4 4 3 C 400 1,6 4 3 3 2 0,8 200 0 qV 100 200 200 300 400 1 400 600 Ped W I A LWA dB(A) C 1 3435 80 0,69 73 C 2 3335 83 0,73 68 C 3 3200 83 0,75 66 C 4 3300 83 0,74 70 D 1 3980 115 1,10 78 D 2 3865 115 1,10 74 D 3 3640 115 1,10 71 D 4 3840 115 1,10 76 E 1 4440 160 1,35 81 E 2 4235 165 1,35 75 E 3 4120 169 1,35 72 E 4 4155 160 1,35 74 2 2 1 pfs Curves: Speed-controlled in H2O Centrifugal module w. support basket Pa kg Centrifugal fan 500 800 1 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 14 ff. Inlet nozzle p. 158 Guard grille p. 160 Electr. connection p. 163 ff. 13 EC centrifugal fans - RadiCal backward curved, O 190, 2 speed stages, 85 W - electronics O4.5 (4x) R3G 190-RB01-01 (Centrifugal fan) Accessory part: Inlet nozzle 09576-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 1 0 45 0 +2 0 O170 O158 O125.5 O190 O132.80.2 O72 O27 O89 O80 2 62.5 O580.2 1.25 68.51 14 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 190-RB01-01 (Centrifugal module with support basket) o225 O5 (4x) 79 o2040.5 6 45 O2 O2650 .5 O2650 44 85 1 0 14 45 6 0+ 20 .5 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 190, 2 speed stages, 170 W - electronics O4.5 (4x) R3G 190-RD45-01 (Centrifugal fan) Accessory part: Inlet nozzle 09576-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O170 O158 O125.5 O190 O132.80.2 O72 O101 O75 5 62.5 O580.2 1.25 881 14 O900.2 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 190-RD45-01 (Centrifugal module with support basket) o225 O5 (4x) 79 o2040.5 6 45 O2 O2650 .5 Mounting dimensions: 45 85 1 0 6 0+ 20 O2650 .5 44 15 EC centrifugal fans - RadiCal backward curved, O 190, speed-controlled, 85 W - electronics O4.5 (4x) R3G 190-RC05-03 (Centrifugal fan) Accessory part: Inlet nozzle 09576-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 1 0 45 0+ 20 O170 O158 O125.5 O190 O132.80.2 O72 O27 O89 O80 2 62.5 O580.2 1.25 68.51 14 2 Connection line AWG 20, 3 x brass lead tips crimped Control line AWG 22, 4 x brass lead tips crimped K3G 190-RC05-03 (Centrifugal module with support basket) o225 O5 (4x) 79 o2040.5 6 45 O2 O2650 .5 85 10 16 45 0+ 6 20 O2650 .5 44 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 190, speed-controlled, 115 W - electronics R3G 190-RG19-01 (Centrifugal fan) O4.5 (4x) Accessory part: Inlet nozzle 09576-2-4013 not included in the standard scope of delivery Depth of screw max. 6 mm Depth of screw max. 6 mm M4 (4x) M4 (4x) R1 O158 O170 O125.5 O132.8 O190 O115 max.O 95 0 45 0 +2 0 10 85 6 95 1.25 62.5 691 14 58 0.2 1050.2 2 Connection line PVC 3G 0.5 mm , 3 x brass lead tips crimped 2 2 Connection line PVC 4X 0.25 mm , 4 x brass lead tips crimped K3G 190-RG19-01 (Centrifugal module with support basket) O5 (4x) 107.5 85.5 225 204 0.5 6 45 O2 66 0. 5 0.5 6 O26 .5 0 4 4 O2 Mounting dimensions: 0 1 0 +2 85 0 45 6 17 EC centrifugal fans - RadiCal backward curved, O 190, speed-controlled, 170 W - electronics R3G 190-RD45-03 (Centrifugal fan) O4.5 (4x) Accessory part: Inlet nozzle 09576-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O170 O158 O125.5 O190 O132.80.2 O72 O101 O75 5 62.5 O580.2 1.25 881 14 2 O900.2 Control line AWG 22, 4 x brass lead tips crimped Connection line AWG 20, 3 x brass lead tips crimped K3G 190-RD45-03 (Centrifugal module with support basket) o225 O5 (4x) 79 o2040.5 6 45 O2 O2650 .5 85 10 18 45 6 0+ 20 O2650 .5 44 Mounting dimensions: 19 EC centrifugal fans - RadiCal backward curved, O 220 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 2580 85 0,70 -25..+60 p. 164 / H3) B 1~ 200-240 50/60 3230 168 1,40 -25..+50 p. 164 / H3) M3G 055-BI C 1~ 200-240 50/60 2580 85 0,70 -25..+60 p. 165 / H4) *3G 220 M3G 055-CF D 1~ 200-240 50/60 2790 115 1,10 -25..+50 p. 163 / H5) *3G 220 M3G 055-CF E 1~ 200-240 50/60 3230 168 1,40 -25..+50 p. 165 / H4) Curve Nominal voltage range Technical features and electrical connection - Material: Housing: PA plastic 6, fibreglass-reinforced Impeller: PA plastic 6, fibreglass-reinforced Rotor: Thick layer passivated Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None, open rotor - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 220 M3G 055-BI A *3G 220 M3G 055-CF *3G 220 Pa 800 600 n rpm max. = 7 3,2 3 2,4 Curves: 2 Speed stages (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations B 4 8 1,6 400 7 A 0,8 200 3 1 2765 79 0,67 71 2 2700 85 0,69 67 A 3 2580 85 0,70 65 A 4 2630 85 0,70 66 A 5 1505 16 0,18 57 A 6 1485 16 0,20 54 A 7 1470 17 0,21 51 A 8 1485 17 0,19 52 B 1 3540 168 1,40 77 B 2 3370 168 1,40 73 B 3 3230 168 1,40 70 B 4 3310 168 1,40 72 B 5 3000 100 0,85 74 B 6 2955 110 0,95 70 B 7 2900 120 1,00 68 B 8 2930 115 0,97 70 6 8 7 6 pfs 5 0 qV 100 200 200 400 5 1 300 400 600 500 800 600 1000 1 700 cfm 1200 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 20 LWA dB(A) A 2 2 I A A 3 4 Ped W Mass of centrifugal fan Mass of centrifugal module with support basket - Technical features: See electrical connections p. 163 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for kg R3G 220-RC05 -01 1,13 K3G 220-RC05 -01 2,03 R3G 220-RD53 -01 1,53 K3G 220-RD53 -01 2,43 R3G 220-RC05 -03 1,20 K3G 220-RC05 -03 2,10 R3G 220-RG19 -01 1,40 K3G 220-RG19 -01 2,00 R3G 220-RD53 -03 1,53 K3G 220-RD53 -03 2,43 800 n rpm max. = 3,2 3 600 2,4 E D 4 Ped W I A LWA dB(A) C 1 2765 79 0,67 71 C 2 2700 85 0,69 67 C 3 2580 85 0,70 65 C 4 2635 85 0,70 66 D 1 3085 115 1,10 74 D 2 2935 115 1,10 69 D 3 2790 115 1,10 66 D 4 2940 115 1,10 70 E 1 3540 168 1,40 77 E 2 3370 168 1,40 73 E 3 3230 168 1,40 70 E 4 3310 168 1,40 72 400 1,6 4 3 4 C 0,8 200 3 3 2 2 2 1 pfs Curves: Speed-controlled in H2O Centrifugal module w. support basket Pa kg Centrifugal fan 0 qV 100 200 200 300 400 400 600 500 800 1 1 600 1000 700 cfm 1200 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 22 ff. Inlet nozzle p. 158 Guard grille p. 160 Electr. connection p. 163 ff. 21 EC centrifugal fans - RadiCal backward curved, O 220, 2 speed stages, 85 W - electronics O5.5 (6x) R3G 220-RC05-01 (Centrifugal fan) Accessory part: Inlet nozzle 09609-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 1 0 45 0+ 20 O252 O242 O155 O220 O1610.2 O72 O27 O89 O80 2 63.7 O580.2 0.8 21 711 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 220-RC05-01 (Centrifugal module with support basket) o270 O5 (4x) 92 o247.50.5 7 45 O2 94 O3050 .5 85 1 0 22 45 6 0+ 20 O3050 .5 .5 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 220, 2 speed stages, 170 W - electronics O5.5 (6x) R3G 220-RD53-01 (Centrifugal fan) Accessory part: Inlet nozzle 09609-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O252 O242 O155 O220 O1610.2 O72 O101 O75 5 63.7 O580.2 0.8 901 21 O900.2 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 220-RD53-01 (Centrifugal module with support basket) o270 O5 (4x) 92 o247.50.5 7 45 O2 94 O3050 .5 Mounting dimensions: 45 85 1 0 6 0+ 20 O3050 .5 .5 23 EC centrifugal fans - RadiCal backward curved, O 220, speed-controlled, 85 W - electronics O5.5 (6x) R3G 220-RC05-03 (Centrifugal fan) Accessory part: Inlet nozzle 09609-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 10 45 0+ 20 O252 O242 O155 O220 O1610.2 O72 O27 O89 O80 2 63.7 O580.2 0.8 711 21 2 Connection line AWG 20, 3 x brass lead tips crimped Control line AWG 22, 4 x brass lead tips crimped K3G 220-RC05-03 (Centrifugal module with support basket) o270 O5 (4x) 92 o247.50.5 7 45 O2 94 O3050 .5 85 10 24 45 0+ 6 20 O3050 .5 .5 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 220, speed-controlled, 115 W - electronics R3G 220-RG19-01 (Centrifugal fan) O5.5 (6x) Accessory part: Inlet nozzle 09609-2-4013 not included in the standard M4 (4x) scope of delivery 95 1 71 1 Depth of screw max. 6 mm Depth of screw max. 6 mm M4 (4x) R2 O242 O252 O155 O161 O220 O115 max.O95 1.8 20 0+ 0 45 51 8 6 O58 0.2 O105 0.2 63.7 0.8 21 2 Connection line PVC 3G 0.5 mm , 3 x brass lead tips crimped 2 2 Connection line PVC 4X 0.25 mm , 4 x brass lead tips crimped K3G 220-RG19-01 (Centrifugal module with support basket) O5 (4x) 116 99 270 247.5 0.5 7 45 O3 05 0. 5 .5 4 29 .5 0 O 0.5 5 O30 Mounting dimensions: 0 1 0 +2 0 85 45 6 25 EC centrifugal fans - RadiCal backward curved, O 220, speed-controlled, 170 W - electronics R3G 220-RD53-03 (Centrifugal fan) O5.5 (6x) Accessory part: Inlet nozzle 09609-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O252 O242 O155 O220 O1610.2 O72 O101 O75 5 63.7 O580.2 0.8 901 21 2 O900.2 Control line AWG 22, 4 x brass lead tips crimped Connection line AWG 20, 3 x brass lead tips crimped K3G 220-RD53-03 (Centrifugal module with support basket) o270 O5 (4x) 92 o247.50.5 7 45 O2 94 O3050 .5 85 10 26 45 6 0+ 20 O3050 .5 .5 Mounting dimensions: 27 EC centrifugal fans - RadiCal backward curved, O 225 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 2200 82 0,70 -25..+60 p. 164 / H3) B 1~ 200-240 50/60 2860 170 1,40 -25..+60 p. 164 / H3) M3G 055-CF C 1~ 200-240 50/60 2200 82 0,70 -25..+60 p. 165 / H4) *3G 225 M3G 055-CF D 1~ 200-240 50/60 2440 115 1,10 -25..+40 p. 163 / H5) *3G 225 M3G 055-DF E 1~ 200-240 50/60 2860 170 1,40 -25..+60 p. 165 / H4) Curve Nominal voltage range Technical features and electrical connection - Material: Housing: PA plastic 6, fibreglass-reinforced Impeller: PA plastic 6, fibreglass-reinforced Rotor: Thick layer passivated Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None, open rotor - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 225 M3G 055-CF A *3G 225 M3G 055-DF *3G 225 Pa 720 3 7 n rpm max. = 2,8 Curves: 2 Speed stages (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations 2,4 640 560 320 4 7 240 0,8 3 A 160 6 7 2 6 pfs 5 0 qV 100 200 200 400 300 400 600 1 500 800 600 1000 1 5 700 1200 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 28 1 2290 70 0,62 69 2 2170 77 0,66 65 A 3 2200 82 0,70 60 A 4 2225 73 0,63 66 A 5 1640 27 0,28 61 A 6 1585 31 0,31 58 A 7 1590 31 0,32 53 A 8 1630 28 0,29 58 B 1 3030 150 1,25 78 B 2 2910 165 1,40 74 B 3 2860 170 1,40 68 B 4 2970 155 1,35 73 B 5 2550 91 0,83 74 B 6 2495 104 0,94 70 B 7 2490 105 0,93 65 B 8 2525 97 0,89 69 8 0,4 80 2 LWA dB(A) A 2,0 3 8 I A A B 1,6 400 1,2 480 4 Ped W Mass of centrifugal fan Mass of centrifugal module with support basket - Technical features: See electrical connections p. 163 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for kg R3G 225-RD05 -01 1,40 K3G 225-RD05 -01 2,00 R3G 225-RE07 -01 1,60 K3G 225-RE07 -01 2,20 R3G 225-RD05 -03 1,40 K3G 225-RD05 -03 2,00 R3G 225-RH19 -01 1,50 K3G 225-RH19 -01 2,10 R3G 225-RE07 -03 1,60 K3G 225-RE07 -03 2,20 n rpm max. = 2,8 720 3 E 2,4 640 560 2,0 480 4 D 1,6 400 3 Ped W I A LWA dB(A) C 1 2290 70 0,62 69 C 2 2170 77 0,66 65 C 3 2200 82 0,70 60 C 4 2225 73 0,63 66 D 1 2685 115 1,10 73 D 2 2445 115 1,10 67 D 3 2440 115 1,10 63 D 4 2640 115 1,10 71 E 1 3030 150 1,25 78 E 2 2910 165 1,40 74 E 3 2860 170 1,40 68 E 4 2970 155 1,35 73 4 C 4 1,2 320 3 240 0,8 3 2 160 2 0,4 80 2 pfs Curves: Speed-controlled in H2O Centrifugal module w. support basket Pa kg Centrifugal fan 0 qV 100 200 200 400 300 400 600 500 800 1 1 600 700 1000 1 1200 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 30 ff. Inlet nozzle p. 158 Guard grille p. 160 Electr. connection p. 163 ff. 29 EC centrifugal fans - RadiCal backward curved, O 225, 2 speed stages, 85 W - electronics O4.5 (4x) R3G 225-RD05-01 (Centrifugal fan) Accessory part: Inlet nozzle 96358-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 1 0 45 0+ 20 O223 O210 O146 O225 O153.50.2 O72 O27 O89 O80 2 88.4 O580.2 1.5 28 991 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 225-RD05-01 (Centrifugal module with support basket) o270 O5 (4x) 112 o247.50.5 7 45 O2 94 O3050 .5 85 1 0 30 45 6 0+ 20 O3050 .5 .5 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 225, 2 speed stages, 170 W - electronics O4.5 (4x) R3G 225-RE07-01 (Centrifugal fan) Accessory part: Inlet nozzle 96358-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O223 O210 O146 O225 O153.50.2 O72 O101 O75 5 88.4 O580.2 1.5 991 28 O900.2 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 225-RE07-01 (Centrifugal module with support basket) o270 O5 (4x) 119 o247.50.5 7 45 O2 94 O3050 .5 Mounting dimensions: 45 85 1 0 6 0+ 20 O3050 .5 .5 31 EC centrifugal fans - RadiCal backward curved, O 225, speed-controlled, 85 W - electronics O4.5 (4x) R3G 225-RD05-03 (Centrifugal fan) Accessory part: Inlet nozzle 96358-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 10 45 0+ 20 O223 O210 O146 O225 O153.50.2 O72 O27 O89 O80 2 88.4 O580.2 1.5 991 28 2 Connection line AWG 20, 3 x brass lead tips crimped Control line AWG 22, 4 x brass lead tips crimped K3G 225-RD05-03 (Centrifugal module with support basket) o270 O5 (4x) 112 o247.50.5 7 45 O2 94 O3050 .5 85 10 32 45 0+ 6 20 O3050 .5 .5 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 225, speed-controlled, 115 W - electronics O4.5 (4x) R3G 225-RH19-01 (Centrifugal fan) 1111 94 1 Accessory part: Inlet nozzle 96358-2-4013 not included in the standard scope of delivery Depth of screw max. 6 mm M4 (4x) M4 (4x) Depth of screw max. 6 mm R2 O210 O223 O146 O153.5 O225 O115 max.O95 5 45 0+ 85 20 10 6 88.4 1.5 28 O58 0.2 O105 0.2 2 Connection line PVC 3G 0.5 mm , 3 x brass lead tips crimped 2 2 Connection line PVC 4X 0.25 mm , 4 x brass lead tips crimped K3G 225-RH19-01 (Centrifugal module with support basket) O5 (4x) 127.15 112 270 247.5 0.5 7 45 O3 05 0.5 .5 4 29 .5 0 O 0.5 5 O30 Mounting dimensions: 0 1 0 +2 0 85 45 6 33 EC centrifugal fans - RadiCal backward curved, O 225, speed-controlled, 170 W - electronics R3G 225-RE07-03 (Centrifugal fan) O4.5 (4x) Accessory part: Inlet nozzle 96358-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O223 O210 O146 O225 O153.50.2 O72 O101 O75 5 88.4 O580.2 1.5 991 28 2 O900.2 Control line AWG 22, 4 x brass lead tips crimped Connection line AWG 20, 3 x brass lead tips crimped K3G 225-RE07-03 (Centrifugal module with support basket) o270 O5 (4x) 119 o247.50.5 7 45 O2 94 O3050 .5 85 10 34 45 6 0+ 20 O3050 .5 .5 Mounting dimensions: 35 EC centrifugal fans - RadiCal backward curved, O 250 Nominal voltage range Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 1955 80 0,70 -25..+60 p. 164 / H3) B 1~ 200-240 50/60 2510 170 1,40 -25..+60 p. 164 / H3) C 1~ 200-240 50/60 1955 80 0,70 -25..+60 p. 165 / H4) D 1~ 200-240 50/60 2510 170 1,40 -25..+60 p. 165 / H4) Curve Nominal data Type Motor *3G 250 M3G 055-CF A *3G 250 M3G 055-DF *3G 250 M3G 055-CF *3G 250 M3G 055-DF (1) Nominal data in operating point with maximum load and 230 VAC 400 7 n rpm max. = 2,4 Pa 500 2,0 600 3 4 1,6 700 in H2O subject to alterations Curves: 2 Speed stages Technical features and electrical connection - Material: Housing: PA plastic 6, fibreglass-reinforced Impeller: PA plastic 6, fibreglass-reinforced Rotor: Thick layer passivated Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "B" - Mounting position: Any - Condensate discharges: None, open rotor - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings I A LWA dB(A) A 1 2050 70 0,60 69 A 2 1965 80 0,68 66 A 3 1955 80 0,70 61 A 4 1990 78 0,65 66 A 5 1325 22 0,23 60 A 6 1290 26 0,26 57 A 7 1290 26 0,28 53 A 8 1330 26 0,26 57 B 1 2680 145 1,15 76 B 2 2565 170 1,40 71 B 3 2510 170 1,40 67 B 4 2610 160 1,30 73 B 5 2330 96 0,80 72 B 6 2265 110 0,92 67 B 7 2250 115 0,96 64 B 8 2285 110 0,93 68 B 8 Ped W 300 1,2 3 4 7 3 0,8 200 2 A 6 8 2 0,4 100 7 6 pfs 5 0 qV 100 200 200 300 400 400 600 1 500 800 600 1000 700 1200 1 5 800 1400 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 36 Mass of centrifugal fan Mass of centrifugal module with support basket - Technical features: See electrical connections p. 164 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for kg R3G 250-RD17 -01 1,50 K3G 250-RD17 -01 2,28 R3G 250-RE07 -05 1,91 K3G 250-RE07 -05 2,69 R3G 250-RD17 -03 1,50 K3G 250-RD17 -03 2,28 R3G 250-RE07 -07 1,91 K3G 250-RE07 -07 2,69 600 3 n rpm max. = 2,4 700 400 100 C 0,8 3 LWA dB(A) C 1 2050 70 0,60 69 C 2 1965 80 0,68 66 C 3 1955 80 0,70 61 C 4 1990 78 0,65 66 D 1 2680 145 1,15 76 D 2 2565 170 1,40 71 D 3 2510 170 1,40 67 D 4 2610 160 1,30 73 2 2 1 1 0 qV I A 4 0,4 200 1,2 3 300 Ped W 4 1,6 500 2,0 D pfs Curves: Speed-controlled in H2O Centrifugal module w. support basket Pa kg Centrifugal fan 100 200 200 300 400 400 600 500 800 600 1000 700 1200 800 1400 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 38 ff. Inlet nozzle p. 158 Guard grille p. 160 Electr. connection p. 164 ff. 37 EC centrifugal fans - RadiCal backward curved, O 250, 2 speed stages, 85 W - electronics O4.5 (4x) R3G 250-RD17-01 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 1 0 45 0+ 20 O255 O240 O164.5 O250 O172.50.2 O72 O27 O89 O80 2 85 O580.2 1.5 31 991 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 250-RD17-01 (Centrifugal module with support basket) o300 O5 (4x) 108.5 o2760.5 7 45 O3 O3400 .5 85 1 0 38 45 6 0+ 20 O3400 .5 22 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 250, 2 speed stages, 170 W - electronics O4.5 (4x) R3G 250-RE07-05 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O255 O240 O164.5 O250 O172.50.2 O72 O101 O75 5 85 O580.2 1.5 991 31 O900.2 Connection line AWG 20, 4 x brass lead tips crimped 2 K3G 250-RE07-05 (Centrifugal module with support basket) o300 O5 (4x) 108.5 o2760.5 7 45 O3 O3400 .5 Mounting dimensions: 45 0+ 85 1 0 6 20 O3400 .5 22 39 EC centrifugal fans - RadiCal backward curved, O 250, speed-controlled, 85 W - electronics O4.5 (4x) R3G 250-RD17-03 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4 (4x) 6 85 1 0 45 0+ 20 O255 O240 O164.5 O250 O172.50.2 O72 O27 O89 O80 2 85 O580.2 1.5 991 31 2 Connection line AWG 20, 3 x brass lead tips crimped Control line AWG 22, 4 x brass lead tips crimped K3G 250-RD17-03 (Centrifugal module with support basket) o300 O5 (4x) 108.5 o2760.5 7 45 O3 O3400 .5 85 10 40 45 0+ 6 20 O3400 .5 22 Mounting dimensions: EC centrifugal fans - RadiCal backward curved, O 250, speed-controlled, 170 W - electronics R3G 250-RE07-07 (Centrifugal fan) O4.5 (4x) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm Depth of screw max. 10 mm M4(4x) M6(4x) 6 85 1 0 45 0+ 20 O255 O240 O164.5 O250 O172.50.2 O72 O101 O75 5 85 O580.2 1.5 991 31 2 O900.2 Control line AWG 22, 4 x brass lead tips crimped Connection line AWG 20, 3 x brass lead tips crimped K3G 250-RE07-07 (Centrifugal module with support basket) o300 O5 (4x) 108.5 o2760.5 7 45 O3 O3400 .5 Mounting dimensions: 45 85 1 0 6 0+ 20 O3400 .5 22 41 EC centrifugal fans - RadiCal backward curved, O 250 A *3G 250 M3G 084-DF B VAC Hz rpm W A C 1~ 200-277 50/60 3740 500 2,20 -25..+60 p. 166 / P5) 1~ 200-277 50/60 4250 750 3,30 -25..+60 p. 166 / P5) (1) Nominal data in operating point with maximum load and 230 VAC Pa Curves: in H2O subject to alterations 1400 max. = 5,6 3 B 1200 4,8 4 4 4,0 600 2,4 400 1,6 200 0,8 800 3 3 2 2 pfs 1 0 qV 200 400 400 600 800 800 1200 1000 1600 1200 2000 1 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. n rpm Ped W I A LWA dB(A) A 1 4100 500 2,20 89 A 2 3870 500 2,20 83 A 3 3740 500 2,20 78 A 4 3860 500 2,20 84 B 1 4250 585 2,60 90 B 2 4250 685 3,00 86 B 3 4250 750 3,30 82 B 4 4250 695 3,10 84 A 3,2 1000 42 Technical features and electrical connection Perm. amb. temp. M3G 084-DF Max. current draw(1) *3G 250 Max. input power(1) Motor Speed/rpm(1) Type Frequency Nominal data Nominal voltage range Curve - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PA Rotor: Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 166 - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 250-RR01 -H1 4,1 K3G 250-RR01 -H2 8,1 R3G 250-RR02 -I1 4,4 K3G 250-RR02 -I2 8,5 Drawings p. 44 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 166 43 EC centrifugal fans - RadiCal backward curved, O 250 R3G 250-RR01-H1 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery 4x O4.5 47.7 Depth of screw max. 16 mm M6 (4x) O240 O255 O164.5 O172 -0.5 O250 +0.3 O178 O150 0.35 8 R2 60 0 +20 0 85 1.5 31 85 106.5 1.8 8 O164 0.35 Connection line AWG 18, 5 x crimped core-end sleeves 2 Connection line AWG 22, 5 x crimped core-end sleeves O11 (4x) O250 K3G 250-RR01-H2 (Centrifugal module with support bracket) 130.5 2 178 3 2 295 350 400 Observe the correct mounting position! Install the support struts only as shown in the view! 44 1 0 EC centrifugal fans - RadiCal backward curved, O 250 R3G 250-RR02-I1 (Centrifugal fan) Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery 4x O4.5 64.1 Depth of screw max. 16 mm M6 (4x) O240 O255 O164.5 O172 -0.5 O250 +0.3 O200 O169 0.35 8 R2 60 0 +20 0 85 1.5 31 85 106.5 1.8 1 0 8 O186 0.5 Connection line AWG 18, 5 x crimped core-end sleeves 2 Connection line AWG 22, 5 x crimped core-end sleeves O11 (4x) O250 K3G 250-RR02-I2 (Centrifugal module with support bracket) 130.5 2 194.6 3 2 295 350 400 Observe the correct mounting position! Install the support struts only as shown in the view! 45 EC centrifugal fans - RadiCal backward curved, O 280 Nominal voltage range Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 1910 168 1,40 -25..+60 p. 165 / H4) B 1~ 200-277 50/60 2700 500 2,20 -25..+60 p. 166 / P5) C 1~ 200-277 50/60 2900 660 2,90 -25..+60 p. 166 / P5) Curve Nominal data Type Motor *3G 280 M3G 074-CF A *3G 280 M3G 084-DF *3G 280 M3G 084-DF 900 A 3,6 Curves: Pa (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations C B C 800 3,2 4 max. 3 =max. 2 = 4 2,8 600 400 3 A 1,6 500 3 2,0 700 2,4 B 2 300 1,2 4 2 2 0,4 pfs 100 0,8 3 200 0 qV 200 400 500 600 1000 800 1500 1000 1200 2000 1 1400 2500 1600 1800 3000 11 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 46 Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PP Rotor: A Surface passivated, B C Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: A "B", B C "F" - Mounting position: A any, B C Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: A None (open rotor), B C Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings n rpm Ped W I A LWA dB(A) A 1 1980 150 1,05 75 A 2 1910 168 1,40 69 A 3 1775 165 1,30 64 A 4 1840 165 1,30 64 B 1 2880 460 2,00 85 B 2 2800 500 2,20 80 B 3 2700 500 2,20 74 B 4 2810 500 2,20 78 C 1 2900 490 2,20 86 C 2 2900 600 2,70 81 C 3 2900 660 2,90 76 C 4 2900 600 2,70 79 Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 165 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 A On account of the installation conditions, ferritic damping in the connection line may be required for the application. - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: A EN 60335-1, CE; B C EN 60335-1, EN 61800-5-1, CE - Approvals: A VDE, CURUS on request; B C VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 280-RB02 -03 2,7 K3G 280-RB02 -03 6,8 R3G 280-RR03 -H1 4,3 K3G 280-RR03 -H2 8,4 R3G 280-RR04 -I1 4,6 K3G 280-RR04 -I2 8,8 Drawings p. 48 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 165 ff. 47 EC centrifugal fans - RadiCal backward curved, O 280 R3G 280-RB02-03 (Centrifugal fan) 4x O4.5 150 Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery 5 M4(4x) M6(4x) Depth of screw max. 10 mm O260 O280 O179.6 O176.7 O187.5 O294 O132.5 O101 O75 R 53 R33 R1 7 20 0+ 60 O90 0.2 O125 6 10 85 1.25 46 127 140 1 8 Connection line AWG 20, 3 x crimped core-end sleeves Connection line AWG 22, 4 x crimped core-end sleeves 177.5 2.5 193.5 3 2 85 6 O11(4x) 600+20 O294 K3G 280-RB02-03 (Centrifugal module with support bracket) 298 350 400 Observe the correct mounting position! Install the support struts only as shown in the view! 48 EC centrifugal fans - RadiCal backward curved, O 280 R3G 280-RR03-H1 (Centrifugal fan) Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery 4x O4.5 47.7 Depth of screw max. 16 mm M6 (4x) R1 7 O260 O280 O179.6 O176.7 O178 O150 0.35 O187.5 0.3 O294 R33 R53 60 0 +20 0 85 1.25 46 127 142.75 1.8 1 0 8 O164 0.5 Connection line AWG 18, 5 x crimped core-end sleeves 8 Connection line AWG 22, 5 x crimped core-end sleeves O11 (4x) O294 K3G 280-RR03-H2 (Centrifugal module with support bracket) 175.5 2 223.2 3 2 295 350 400 Observe the correct mounting position! Install the support struts only as shown in the view! 49 EC centrifugal fans - RadiCal backward curved, O 280 R3G 280-RR04-I1 (Centrifugal fan) Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery 4x O4.5 M6 (4x) 64.1 Depth of screw max. 16 mm R1 7 O260 O280 O179.6 O176.7 O200 O169 0.35 O187.5 0.3 O294 R33 R53 60 0 +20 0 85 1.25 46 8 O186 0.5 127 142.75 1.8 Connection line AWG 18, 5 x crimped core-end sleeves 8 Connection line AWG 22, 5 x crimped core-end sleeves O11 (4x) O294 K3G 280-RR04-I2 (Centrifugal module with support bracket) 175.5 2 239.6 3 2 295 350 400 Observe the correct mounting position! Install the support struts only as shown in the view! 50 1 0 51 EC centrifugal fans - RadiCal backward curved, O 310 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 1525 150 1,20 -25..+60 p. 165 / H4) B 1~ 200-277 50/60 2360 500 2,20 -25..+60 p. 166 / P5) M3G 084-FA C 1~ 200-277 50/60 2640 740 3,25 -25..+60 p. 166 / P5) M3G 084-FA D 3~ 380-480 50/60 2700 790 1,25 -25..+60 p. 167 / P6) Curve Nominal voltage range Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PP Rotor: A Surface passivated, B C D Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: A "B", B C D "F" - Mounting position: A any, B C D Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: A None (open rotor), B C D Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 310 M3G 074-CF A *3G 310 M3G 084-DF *3G 310 *3G 310 (1) Nominal data in operating point with maximum load and 230 or 400 VAC 1000 4,0 Pa max. = 3 900 3,6 Curves: in H2O subject to alterations 3,2 700 400 300 3 3 2,0 2 4 0,8 3 2 pfs 1 0 qV 500 500 1000 1000 1500 1 1500 2000 2500 1 cfm 2000 3000 3500 4000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 52 LWA dB(A) 1 1600 115 0,95 69 A 2 1545 140 1,10 65 A 3 1525 150 1,20 59 A 4 1545 140 1,15 62 B 1 2510 430 1,90 81 B 2 2440 500 2,20 76 B 3 2360 500 2,20 72 B 4 2410 500 2,20 77 C 1 2700 550 2,45 84 C 2 2700 730 3,20 79 C 3 2640 740 3,25 75 C 4 2700 730 3,20 79 D 1 2700 560 0,89 84 D 2 2700 720 1,15 79 D 3 2700 790 1,25 76 D 4 2700 725 1,15 80 A 0,4 100 I A A 2 200 Ped W 3 1,6 500 4 1,2 600 C B 2,4 800 2,8 D 4 n rpm Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 165 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 A On account of the installation conditions, ferritic damping in the connection line may be required for the application. - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: A EN 60335-1, CE; B C D EN 60335-1, EN 61800-5-1, CE - Approvals: A VDE, CURUS on request; B C D VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 310-RB01 -03 2,9 K3G 310-RB01 -03 7,5 R3G 310-RR05 -H1 4,7 K3G 310-RR05 -H2 9,6 R3G 310-RS01 -I1 5,7 K3G 310-RS01 -I2 10,7 R3G 310-RS05 -J1 5,5 K3G 310-RS05 -J2 10,5 Drawings p. 54 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 165 ff. 53 EC centrifugal fans - RadiCal backward curved, O 310 R3G 310-RB01-03 (Centrifugal fan) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery M4(4x) M6(4x) 4x O4.5 163.4 R45.4 O280 O300 O204 O325.5 O193.4 O191.4 4.3 R71.1 R2 5 O132.5 O101 O75 Depth of screw max. 10 mm 0 +2 0 60 6 85 1.5 58.5 O90 0.2 O125 0 1 141.5 153 1 8 Connection line AWG 20, 3 x crimped core-end sleeves Connection line AWG 22, 4 x crimped core-end sleeves O6.4 (8x) O325.5 K3G 310-RB01-03 (Centrifugal module with support bracket) 200 2.5 216 3 2 320 420 440 Observe the correct mounting position! Install the support struts only as shown in the view! 54 EC centrifugal fans - RadiCal backward curved, O 310 R3G 310-RR05-H1 (Centrifugal fan) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery 4x O4.5 M6 (4x) 47.7 O280 O300 O193.4 O191.5 O204 0.4 O325.5 O178 O150 0.35 4 R7 1 R45 R2 Depth of screw max. 16 mm 60 + 0 20 85 0 10 1.5 58.5 141.5 153 2 8 O164 0.35 Connection line AWG 18, 5 x crimped core-end sleeves 8 Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O325.5 K3G 310-RR05-H2 (Centrifugal module with support bracket) 200 2 247.73 2 320 420 440 Observe the correct mounting position! Install the support struts only as shown in the view! 55 EC centrifugal fans - RadiCal backward curved, O 310 R3G 310-RS01-I1 (Centrifugal fan) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery Depth of screw max. 16 mm 4x O4.5 M6 (4x) 64.1 R2 4 O280 O300 O193.4 O191.5 O204 0.4 O325.5 O200 O169 0.35 R45 R71 60 + 0 20 85 0 10 1.5 58.5 141.5 168 2 8 O186 0.35 Connection line AWG 18, 5 x crimped core-end sleeves 8 Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O325.5 K3G 310-RS01-I2 (Centrifugal module with support bracket) 215 2 279 3 2 320 420 440 Observe the correct mounting position! Install the support struts only as shown in the view! 56 EC centrifugal fans - RadiCal backward curved, O 310 R3G 310-RS05-J1 (Centrifugal fan) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery Depth of screw max. 16 mm 4x O4.5 M6 (4x) 64.1 R2 4 O280 O300 O193.4 O191.5 O204 0.4 O325.5 O200 O169 0.35 R45 R71 60 + 0 20 85 0 10 1.5 58.5 141.5 168 2 8 O186 0.35 Connection line AWG 18, 6 x crimped core-end sleeves 8 Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O325.5 K3G 310-RS05-J2 (Centrifugal module with support bracket) 215 2 279 3 2 320 420 440 Observe the correct mounting position! Install the support struts only as shown in the view! 57 EC centrifugal fans - RadiCal backward curved, O 355 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-240 50/60 1250 168 1,40 -25..+60 p. 165 / H4) B 1~ 200-277 50/60 1450 250 1,10 -25..+60 p. 166 / P5) M3G 084-FA C 1~ 200-277 50/60 1850 500 2,20 -25..+60 p. 166 / P5) *3G 355 M3G 084-GF D 1~ 200-277 50/60 2100 750 3,30 -25..+60 p. 166 / P5) *3G 355 M3G 112-EA E 3~ 380-480 50/60 2400 1140 1,80 -25..+60 p. 167 / P6) Curve Nominal voltage range Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PP Rotor: A Surface passivated, B C D E Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: A "B", B C D E "F" - Mounting position: A any, B C D E Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: A None (open rotor), B C D E Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 355 M3G 074-CF A *3G 355 M3G 084-DF *3G 355 1000 4,0 900 3,6 E 800 3 max. = 400 1425 165 1,35 71 1305 165 1,35 65 A 3 1250 168 1,40 58 A 4 1280 165 1,35 60 B 1 1660 250 1,10 77 B 2 1505 250 1,10 68 B 3 1450 250 1,10 63 B 4 1525 250 1,10 68 C 1 2050 455 2,00 87 C 2 1940 500 2,20 78 C 3 1850 500 2,20 300 70 C 4 1890 500 2,20 73 D 1 2240 630 2,75 87 D 2 2165 750 3,30 81 D 3 2100 750 3,30 74 D 4 2165 740 3,25 77 cfm E 1 2400 790 1,25 91 m3/h E 2 2400 1040 1,65 83 E 3 2400 1140 1,80 76 E 4 2400 1090 1,70 79 2,8 2,4 2,0 2 3 4 2 3 0,8 4 200 3 A 1,6 500 4 LWA dB(A) 2 3 B I A 1 C 1,2 600 Ped W A 4 700 n rpm A 4 D 3,2 Curves: Pa (1) Nominal data in operating point with maximum load and 230 or 400 VAC in H2O subject to alterations 2 3 0,4 2 100 2 pfs 1 0 qV 500 1000 1000 1500 2000 1 2000 3000 1 2500 4000 1 3000 5000 1 Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 58 Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 165 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 A On account of the installation conditions, ferritic damping in the connection line may be required for the application. - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: A EN 60335-1, CE; B C D E EN 60335-1, EN 61800-5-1, CE - Approvals: A VDE, CURUS on request; B C D E VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 355-RB03 -03 3,7 K3G 355-RB03 -03 9,7 R3G 355-RR06 -G1 5,0 K3G 355-RR06 -G2 10,8 R3G 355-RS02 -H1 5,7 K3G 355-RS02 -H2 11,6 R3G 355-RT01 -I1 6,9 K3G 355-RT01 -I2 14,9 R3G 355-RJ75 -01 8,3 K3G 355-RJ75 -01 16,3 Drawings p. 60 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 165 ff. 59 EC centrifugal fans - RadiCal backward curved, O 355 R3G 355-RB03-03 (Centrifugal fan) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery M4(4x) M6(4x) 4x O4.5 181.4 Depth of screw max. 10 mm O325 O350 O237 O372.5 O227 O223 O132.5 O101 O75 2.5 R69.5 R2 R43.5 5 60 0 +2 0 6 10 O90 0.2 O125 Connection line AWG 20, 3 x crimped core-end sleeves 0 1 85 1.5 60 161.5 171 1 Connection line AWG 22, 4 x crimped core-end sleeves O6.4 (8x) O372.5 K3G 355-RB03-03 (Centrifugal module with support bracket) 226 2 242 3 2 351 476 496 Observe the correct mounting position! Install the support struts only as shown in the view! 60 EC centrifugal fans - RadiCal backward curved, O 355 R3G 355-RR06-G1 (Centrifugal fan) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery Depth of screw max. 16 mm M6 (4x) 4x O4.5 47.7 2.5 O325 O350 O227 O223 O237 -0.4 O372.5 +1.5 O178 O150 0.35 R69.5 R43.5 R2 60 + 0 20 85 0 10 1.5 60 161.75 170 2 10 8 O164 0.35 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O372.5 K3G 355-RR06-G2 (Centrifugal module with support bracket) 2172 265 3 2 351.5 476 496 Observe the correct mounting position! Install the support struts only as shown in the view! 61 EC centrifugal fans - RadiCal backward curved, O 355 R3G 355-RS02-H1 (Centrifugal fan) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery Depth of screw max. 16 mm 4x O4.5 M6 (4x) 47.7 2.5 O325 O350 O227 O223 O237 -0.4 O372.5 +1.5 O178 O150 0.35 R69.5 R43.5 R2 60 + 0 20 85 0 10 1.5 60 161.75 183 2 10 8 O164 0.35 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O372.5 K3G 355-RS02-H2 (Centrifugal module with support bracket) 229 2 277 3 2 351.5 476 496 Observe the correct mounting position! Install the support struts only as shown in the view! 62 EC centrifugal fans - RadiCal backward curved, O 355 R3G 355-RT01-I1 (Centrifugal fan) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery Depth of screw max. 16 mm 4x O4.5 M6 (4x) 64.1 2.5 O325 O350 O227 O223 O237 -0.4 O372.5 +1.5 O200 O169 0.35 R69.5 R43.5 R2 60 0 +20 0 85 1.5 60 1 0 8 O186 0.5 161.75 191 2 Connection line AWG 18, 5 x crimped core-end sleeves 10 Connection line AWG 22, 5 x crimped core-end sleeves O11 (4x) O372.5 K3G 355-RT01-I2 (Centrifugal module with support bracket) 2372 3013 15 372 450 500 Observe the correct mounting position! Install the support struts only as shown in the view! 63 EC centrifugal fans - RadiCal backward curved, O 355 R3G 355-RJ75-01 (Centrifugal fan) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery Depth of screw 8-10 mm 4x O 4.5 M6 (4x) 8 85 10 850 +20 O 227 O 223 O 325 O 350 +1.5 O 237 -0.4 O 372.5 45 2.5 O 200 O169 4x90 R2 R69.5 R43.5 56.5 60 162 1912 1.5 O 186 0.5 10 Connection line PVC AWG 18, 6 x crimped core-end sleeves Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11 (4x) O 372.5 K3G 355-RJ75-01 (Centrifugal module with support bracket) 237.5 2.5 294 3 15 372 450 500 Observe the correct mounting position! Install the support struts only as shown in the view! 64 65 EC centrifugal fans - RadiCal backward curved, O 400 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-277 50/60 1170 250 1,10 -25..+60 p. 166 / P5) B 1~ 200-277 50/60 1500 500 2,20 -25..+50 p. 166 / P5) M3G 084-GF C 1~ 200-277 50/60 1700 750 3,30 -25..+55 p. 166 / P5) M3G 112-EA D 3~ 380-480 50/60 2060 1320 2,10 -25..+50 p. 167 / P6) Curve Nominal voltage range Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PP Rotor: Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 400 M3G 084-DF A *3G 400 M3G 084-FA *3G 400 *3G 400 (1) Nominal data in operating point with maximum load and 230 or 400 VAC 4,0 Pa 1000 900 3,6 3 800 4 B 500 2,8 4 A 1,6 2 1,2 3 300 Ped W I A LWA dB(A) A 1 1320 240 1,05 75 A 2 1200 250 1,10 71 A 3 1170 250 1,10 61 A 4 1210 250 1,10 67 B 1 1725 500 2,20 80 B 2 1550 500 2,20 73 B 3 1500 500 2,20 68 B 4 1550 500 2,20 72 C 1 1925 740 3,25 83 C 2 1755 750 3,30 78 C 3 1700 750 3,30 72 C 4 1745 750 3,30 72 D 1 2120 965 1,55 89 D 2 2110 1240 2,00 82 D 3 2060 1320 2,10 74 D 4 2110 1270 2,05 79 4 3 400 n rpm C 2,4 600 D 3 2,0 700 max. = 3,2 Curves: in H2O subject to alterations 4 2 0,8 pfs 100 2 2 0,4 200 3 0 qV 500 1000 1000 2000 1500 2000 3000 1 2500 4000 1 3000 5000 1 3500 1 cfm 6000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 66 Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 166 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, EN 61800-5-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 400-RR07 -G1 5,6 K3G 400-RR07 -G2 12,5 R3G 400-RS03 -H1 6,4 K3G 400-RS03 -H2 13,3 R3G 400-RT02 -I1 7,3 K3G 400-RT02 -I2 15,3 R3G 400-RJ75 -01 8,5 K3G 400-RJ75 -01 16,5 Drawings p. 68 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 166 ff. 67 EC centrifugal fans - RadiCal backward curved, O 400 R3G 400-RR07-G1 (Centrifugal fan) 4x O4.5 Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery 47.7 Depth of screw max. 16 mm M6 (4x) R2 O345 O370 O257 O266 0.5 O420 O178 O150 0.35 R50 R90 2 60 0 +20 0 85 1 0 8 1.5 66 O164 0.35 182 194 2 10 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O420 K3G 400-RR07-G2 (Centrifugal module with support bracket) 246.5 2 294 3 2 382 520 560 Observe the correct mounting position! Install the support struts only as shown in the view! 68 EC centrifugal fans - RadiCal backward curved, O 400 R3G 400-RS03-H1 (Centrifugal fan) Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery 4x O4.5 Depth of screw max. 16 mm 47.7 M6 (4x) R2 O345 O370 O257 O266 0.5 O420 O178 O150 0.35 R50 R90 2 60 0 +20 0 85 1 0 8 1.5 66 O164 0.35 182 194 2 10 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O6.4 (8x) O420 K3G 400-RS03-H2 (Centrifugal module with support bracket) 246.5 2 294 3 2 382 520 560 Observe the correct mounting position! Install the support struts only as shown in the view! 69 EC centrifugal fans - RadiCal backward curved, O 400 R3G 400-RT02-I1 (Centrifugal fan) Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery 4x O4.5 Depth of screw max. 16 mm 64.1 M6 (4x) R2 O345 O370 O257 O266 0.5 O420 O200 O169 0.35 R50 R90 2 60 0 +20 0 85 O186 0.5 10 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O11 (4x) O420 K3G 400-RT02-I2 (Centrifugal module with support bracket) 244 2 308 3 15 372 450 500 Observe the correct mounting position! Install the support struts only as shown in the view! 70 0 8 1.5 66 182 192 2 1 EC centrifugal fans - RadiCal backward curved, O 400 R3G 400-RJ75-01 (Centrifugal fan) 4x O 4.5 Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery Depth of screw max. 16 mm 56.5 M6 (4x) 4x90 R2 O 345 O 370 8 85 10 850 +20 O 257 O 200 O169 O 266 0.5 O 420 R50 R 90 45 2 66 182 192 2 1.5 O 186 0.5 10 Connection line PVC AWG 18, 6 x crimped core-end sleeves Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11 (4x) O 420 K3G 400-RJ75-01 (Centrifugal module with support bracket) 246 2.5 302.5 3 15 372 450 500 Observe the correct mounting position! Install the support struts only as shown in the view! 71 EC centrifugal fans - RadiCal backward curved, O 450 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-277 50/60 1000 250 1,10 -25..+60 p. 166 / P5) B 1~ 200-277 50/60 1260 500 2,20 -25..+50 p. 166 / P5) M3G 112-EA C 1~ 200-277 50/60 1440 750 3,30 -25..+60 p. 166 / P5) M3G 112-GA D 3~ 380-480 50/60 1550 950 1,50 -25..+60 p. 167 / P6) Curve Nominal voltage range Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate: Sheet steel, galvanised / Inlet nozzle: Plastic ABS Impeller: Plastic PP Rotor: Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 450 M3G 084-FA A *3G 450 M3G 084-GF *3G 450 *3G 450 (1) Nominal data in operating point with maximum load and 230 or 400 VAC Pa Curves: 600 2,4 in H2O subject to alterations 3 max. = B 2,0 D C 1,6 3 400 4 1,2 3 4 2 0,8 200 2 3 0,4 pfs 2 0 qV 500 1000 1000 2000 1500 2000 3000 2500 4000 1 3000 5000 1 3500 1 cfm 6000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 72 LWA dB(A) 1 1130 230 1,05 76 A 2 1050 250 1,10 68 A 3 1000 250 1,10 62 A 4 1031 250 1,10 70 B 1 1470 500 2,00 95 B 2 1345 500 2,20 80 B 3 1260 500 2,20 69 B 4 1295 500 2,20 71 C 1 1550 570 2,55 79 C 2 1525 750 3,30 78 C 3 1440 750 3,30 72 C 4 1495 750 3,30 76 D 1 1550 600 1,00 79 D 2 1550 820 1,35 78 D 3 1550 950 1,50 74 D 4 1550 880 1,40 75 2 100 I A A 3 A 300 Ped W 4 4 500 n rpm Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 166 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: Variable - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 60335-1, EN 61800-5-1, CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 450-RS04 -G1 6,7 K3G 450-RS04 -G2 16,5 R3G 450-RT03 -H1 7,5 K3G 450-RT03 -H2 17,3 R3G 450-RJ74 -21 9,2 K3G 450-RJ74 -21 19,3 R3G 450-RK56 -01 10,6 K3G 450-RK56 -01 20,7 Drawings p. 74 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 166 ff. 73 EC centrifugal fans - RadiCal backward curved, O 450 R3G 450-RS04-G1 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery Depth of screw max. 16 mm 6x O9 M6 (4x) 47.7 R2 O425 O450 O292 O286.7 O300 0.5 O485 O178 O150 0.35 R50 R40 0 60 0 +20 0 85 1 0 8 3 50 O164 0.35 218 226 2 10 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O11 (8x) O485 K3G 450-RS04-G2 (Centrifugal module with support bracket) 260.5 2 308 3 15 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 74 EC centrifugal fans - RadiCal backward curved, O 450 R3G 450-RT03-H1 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery Depth of screw max. 16 mm 6x O9 M6 (4x) 47.7 R2 O425 O450 O292 O286.7 O300 0.5 O485 O178 O150 0.35 R50 R40 0 60 0 +20 0 85 1 0 8 3 50 O164 0.35 218 226 2 10 Connection line AWG 18, 5 x crimped core-end sleeves Connection line AWG 22, 5 x crimped core-end sleeves O11 (8x) O485 K3G 450-RT03-H2 (Centrifugal module with support bracket) 260.5 2 308 3 15 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 75 EC centrifugal fans - RadiCal backward curved, O 450 R3G 450-RJ74-21 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery Depth of screw max. 16 mm M6 (4x) 4x90 6x O 9 56.5 8 85 10 850 +20 O 425 O 450 O292 O 286.7 O 300 0.5 O 485 O 200 O169 0 45 R50 R 40 R2 218 233.5 2 50 10 3 O 186 0.5 Connection line PVC AWG 18, 5 x crimped core-end sleeves Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11 (8x) K3G 450-RJ74-21 (Centrifugal module with support bracket) 15 268 2.5 324.5 3 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 76 EC centrifugal fans - RadiCal backward curved, O 450 R3G 450-RK56-01 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery Depth of screw max. 16 mm M6 (4x) 4x90 6x O 9 56.5 8 85 10 850 +20 O 425 O 450 O292 O 286.7 O 300 0.5 O 485 O 200 O169 0 45 R50 R 40 R2 218 233.5 2 50 10 3 O 186 0.5 Connection line PVC AWG 18, 6 x crimped core-end sleeves Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11 (8x) K3G 450-RK56-01 (Centrifugal module with support bracket) 15 268 2.5 324.5 3 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 77 EC centrifugal fans - RadiCal backward curved, O 500 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-277 50/60 750 250 1,10 -25..+60 p. 166 / P5) B 1~ 200-277 50/60 900 460 2,00 -25..+40 p. 166 / P5) M3G 112-GA C 1~ 200-277 50/60 1100 750 3,30 -25..+60 p. 166 / P5) *3G 500 M3G 112-IA D 3~ 380-480 50/60 1350 1320 2,10 -25..+50 p. 167 / P6) *3G 500 M3G 150-FF E 3~ 380-480 50/60 1700 2600 4,00 -25..+60 p. 169 / M5) Curve Nominal voltage range Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate: Sheet steel, galvanised / Inlet nozzle: Plastic ABS Impeller: Plastic PP Rotor: Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 500 M3G 084-FA A *3G 500 M3G 084-GF *3G 500 1100 1000 Pa Curves: 4,4 in H2O (1) Nominal data in operating point with maximum load and 230 or 400 VAC 4,0 subject to alterations 3 n rpm max. = E 3,2 700 D 2,4 500 4 2,0 3 1,6 300 1,2 4 400 A 2 B 3 4 2 4 0,8 200 3 3 2 2 pfs 1 0 qV 1000 2000 2000 1 3000 4000 4000 6000 1 5000 825 230 1,00 68 2 765 250 1,10 62 A 3 750 250 1,10 56 A 4 795 250 1,10 59 B 1 900 300 1,30 70 B 2 900 410 1,80 66 B 3 900 460 2,00 62 B 4 900 400 1,75 61 C 1 1250 750 3,30 77 C 2 1155 750 3,30 73 C 3 1100 750 3,30 67 C 4 1150 750 3,30 69 D 1 1495 1215 1,90 82 D 2 1410 1320 2,10 77 D 3 1350 1320 2,10 71 D 4 1420 1320 2,10 76 8000 1 6000 1 cfm E 1 1695 1790 2,80 86 10000 m3/h E 2 1695 2300 3,60 82 E 3 1700 2600 4,00 77 E 4 1695 2230 3,50 81 Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 78 1 A 2 0,4 100 LWA dB(A) 3 C 600 I A A 4 3,6 800 2,8 900 Ped W E EN 61800-5-1, CE Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 166 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Cable exit: A B C D Variable - Terminal box design: E Electrical connection via terminal strip - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: A B C D EN 60335-1, EN 61800-5-1, CE; - Approvals: VDE, UL, CSA, CCC, GOST are applied for Centrifugal fan kg Centrifugal module w. support bracket kg R3G 500-RS06 -G1 8,6 K3G 500-RS06 -G2 18,9 R3G 500-RT04 -H1 9,5 K3G 500-RT04 -H2 19,7 R3G 500-RK55 -21 12,6 K3G 500-RK55 -21 23,1 R3G 500-RL96 -01 14,1 K3G 500-RL96 -01 24,6 R3G 500-RA24 -71 21,0 K3G 500-RA24 -71 35,0 Drawings p. 80 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 166 ff. 79 EC centrifugal fans - RadiCal backward curved, O 500 R3G 500-RS06-G1 (Centrifugal fan) Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery 6x O9 47.7 Depth of screw max. 16 mm M6 (4x) R2 O445 O470 O525 O319.5 1.0 O334.3+-0.5 O178 O150 0.35 R87 R49 8 60 0 85 3.5 75 1 0 8 O164 0.35 227 256.5 3 +2 0 0 Connection line AWG 18, 5 x crimped core-end sleeves 12 Connection line AWG 22, 5 x crimped core-end sleeves O11 (8x) O525 K3G 500-RS06-G2 (Centrifugal module with support bracket) 311.5 2 359 3 15 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 80 EC centrifugal fans - RadiCal backward curved, O 500 R3G 500-RT04-H1 (Centrifugal fan) Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery Depth of screw max. 16 mm 6x O9 M6 (4x) 47.7 R2 O445 O470 O525 O319.5 1.0 O334.5+-0.5 O178 O150 0.35 R87 R49 8 60 0 85 3.5 75 1 0 8 O164 0.35 227 256.5 3 +2 0 0 Connection line AWG 18, 5 x crimped core-end sleeves 12 Connection line AWG 22, 5 x crimped core-end sleeves O11 (8x) O525 K3G 500-RT04-H2 (Centrifugal module with support bracket) 311.5 2 359 3 15 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 81 EC centrifugal fans - RadiCal backward curved, O 500 R3G 500-RK55-21 (Centrifugal fan) Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery M6 (4x) Depth of screw max. 16 mm 6x O9 4x9 0 56.5 R 49 8 85 10 850 +20 O 445 O 470 O 324.5 O 319.5 O 334.3 0.5 O 525 R87 O 200 O169 8 45 R2 75 227 247.5 2 10 3.5 O 186 0.5 Connection line PVC AWG 18, 5 x crimped core-end sleeves Connection line PVC AWG 22, 5 x crimped core-end sleeves O11 (8x) K3G 500-RK55-21 (Centrifugal module with support bracket) 15 304.52.5 361 3 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 82 EC centrifugal fans - RadiCal backward curved, O 500 R3G 500-RL96-01 (Centrifugal fan) Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery M6 (4x) Depth of screw max. 16 mm 6x O9 4x9 0 56.5 R 49 8 85 10 850 +20 O 445 O 470 O 324.5 O 319.5 O 200 O169 +1 R87 O 334.5 -0.5 O 525 8 45 R2 75 227 247.5 2 10 3.5 O 186 0.5 Connection line PVC AWG 18, 6 x crimped core-end sleeves Connection line PVC AWG 22, 5 x crimped core-end sleeves O11 (8x) K3G 500-RL96-01 (Centrifugal module with support bracket) 15 304.52.5 361 3 549 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 83 EC centrifugal fans - RadiCal backward curved, O 500 R3G 500-RA24-71 (Centrifugal fan) Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery Depth of screw max. 25 mm 6x O9 M10 (6x) 70 R 49 O445 O470 O319.5 +1 O334.5-0.5 O525 O232 -2 0 6x6 8 R2 R 87 3.5 75 227 2582 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm 12 O11 (8x) O525 K3G 500-RA24-71 (Centrifugal module with support bracket) 314 2 384 3 15 551 580 630 Observe the correct mounting position! Install the support struts only as shown in the view! 84 Tightening torque 3.50.5 Nm 85 EC centrifugal fans - RadiCal backward curved, O 560 Nominal voltage range Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-277 50/60 1340 1590 7,00 -25..+55 p. 168 / M4) B 3~ 380-480 50/60 1540 2360 3,65 -25..+60 p. 169 / M5) C 3~ 380-480 50/60 1650 2900 4,40 -25..+55 p. 169 / M5) Curve Nominal data Type Motor *3G 560 M3G 150-FF A *3G 560 M3G 150-FF *3G 560 M3G 150-IF Curves: Pa (1) Nominal data in operating point with maximum load and 230 or 400 VAC in H2O subject to alterations 900 3,6 800 3,2 3 max. = C 4 A 2,8 700 2,0 400 300 4 3 2 2 1,2 500 1,6 2,4 3 600 0,8 pfs 100 0,4 2 200 0 qV 1000 2000 2000 4000 n rpm Ped W I A LWA dB(A) 4 B 3 3000 4000 6000 5000 8000 6000 10000 1 7000 12000 11 8000 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 86 Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PP Rotor: Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings A 1 1340 1120 4,90 83 A 2 1340 1460 6,40 78 A 3 1340 1590 7,00 74 A 4 1340 1520 6,65 76 B 1 1540 1840 2,90 86 B 2 1540 2300 3,60 81 B 3 1540 2360 3,65 78 B 4 1540 2310 3,60 80 C 1 1650 2010 3,10 87 C 2 1650 2630 4,10 81 C 3 1650 2900 4,40 77 C 4 1650 2770 4,30 80 Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 168 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Terminal box design: Electrical connection via terminal strip - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 61800-5-1; CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for kg Centrifugal module w. support bracket kg R3G 560-RA25 -21 22,5 K3G 560-RA25 -21 43,2 R3G 560-RA25 -71 21,6 K3G 560-RA25 -71 42,3 R3G 560-RB31 -71 26,0 K3G 560-RB31 -71 46,7 Centrifugal fan Drawings p. 88 ff. Inlet nozzle p. 158 ff. Electr. connection p. 168 ff. 87 EC centrifugal fans - RadiCal backward curved, O 560 R3G 560-RA25-21 (Centrifugal fan) Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery Depth of screw max. 25 mm O9 (6x) M10 (6x) 70 6x6 O540 O565 O407 O418 0.7 O570 O232 -2 0 0 R5 Tightening torque 3.50.5 Nm 1.5 83.5 253 289 2 18 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm O11 (8x) O570 K3G 560-RA25-21 (Centrifugal module with support bracket) 346 2 416 3 15 551 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 88 EC centrifugal fans - RadiCal backward curved, O 560 R3G 560-RA25-71 (Centrifugal fan) Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery Depth of screw max. 25 mm O9 (6x) M10 (6x) 70 6x6 O540 O565 O407 O418 0.7 O570 O232 -2 0 0 R5 Tightening torque 3.50.5 Nm 1.5 83.5 253 289 2 18 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm O11 (8x) O570 K3G 560-RA25-71 (Centrifugal module with support bracket) 346 2 416 3 15 551 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 89 EC centrifugal fans - RadiCal backward curved, O 560 R3G 560-RB31-71 (Centrifugal fan) Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery Depth of screw max. 25 mm O9 (6x) M10 (6x) 70 6x6 O540 O565 O407 O418 0.7 O570 O232 -2 0 0 R5 Tightening torque 3.50.5 Nm 1.5 83.5 253 289 2 18 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm O11 (8x) O570 K3G 560-RB31-71 (Centrifugal module with support bracket) 346 2 416 3 15 551 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 90 91 EC centrifugal fans - RadiCal backward curved, O 630 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Perm. amb. temp. VAC Hz rpm W A C 1~ 200-277 50/60 740 500 2,20 -25..+40 p. 166 / P5) B 1~ 200-277 50/60 840 750 3,30 -25..+40 p. 166 / P5) M3G 112-IA C 3~ 380-480 50/60 900 950 1,50 -25..+40 p. 167 / P6) *3G 630 M3G 150-FF D 1~ 200-277 50/60 1030 1415 6,20 -25..+50 p. 168 / M4) *3G 630 M3G 150-FF E 3~ 380-480 50/60 1130 1790 2,80 -25..+60 p. 169 / M5) *3G 630 M3G 150-IF F 3~ 380-480 50/60 1300 2700 4,15 -25..+55 p. 169 / M5) Curve Nominal voltage range Technical features and electrical connection - Material: Support bracket: Steel, coated in black Support plate and inlet nozzle: Sheet steel, galvanised Impeller: Plastic PP Rotor: Coated in black Electronics enclosure: Die-cast aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *3G 630 M3G 112-IA A *3G 630 M3G 112-IA *3G 630 (1) Nominal data in operating point with maximum load and 230 or 400 VAC Pa 400 B n rpm max. = 3 4 1 825 460 2,00 76 2 770 500 2,20 69 A 3 740 500 2,20 65 A 4 750 500 2,20 67 B 1 930 690 3,00 80 B 2 880 750 3,30 73 B 3 840 750 3,30 70 B 4 865 750 3,30 71 C 1 900 600 1,00 78 C 2 900 830 1,30 73 2 C 3 900 950 1,50 69 2 C 4 900 885 1,40 71 C 1,2 3 4 0,8 3 0,4 3 2 0 pfs 100 qV 1000 2000 2000 4000 3000 4000 6000 5000 8000 1 6000 10000 1 1 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 92 LWA dB(A) A A 200 I A A 4 300 Ped W 1,6 Curves: in H2O subject to alterations Mass of centrifugal fan Mass of centrifugal module with support bracket - Technical features: See electrical connections p. 166 ff. - EMC: Interference emission acc. to EN 61000-6-3 Interference immunity acc. to EN 61000-6-2 Harmonics acc. to EN 61000-3-2/3 - Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) - Terminal box design: Electrical connection via terminal strip - Protection class: I (if customer has provided connection for protective earth) - Product conforming to standards: EN 61800-5-1; CE - Approvals: VDE, UL, CSA, CCC, GOST are applied for kg R3G 630-RK57 -31 15,8 K3G 630-RK57 -31 34,8 R3G 630-RL94 -21 17,6 K3G 630-RL94 -21 36,6 R3G 630-RL95 -01 17,4 K3G 630-RL95 -01 36,4 R3G 630-RA38 -21 25,0 K3G 630-RA38 -21 50,0 R3G 630-RA21 -71 24,0 K3G 630-RA21 -71 49,0 R3G 630-RB32 -71 29,0 K3G 630-RB32 -71 54,0 3 4 n rpm max. = 2,4 E 600 3 4 2,0 D 500 1,6 300 1,2 4 400 2 0,8 0,4 2 100 LWA dB(A) D 1 1030 920 4,00 82 D 2 1030 1240 5,45 75 D 3 1030 1415 6,20 74 D 4 1030 1230 5,40 77 E 1 1130 1180 1,95 84 E 2 1130 1640 2,60 77 E 3 1130 1790 2,80 74 E 4 1130 1750 2,80 75 F 1 1300 1780 2,80 87 F 2 1300 2420 3,75 81 F 3 1300 2700 4,15 77 F 4 1300 2640 4,10 80 2 1 0 qV I A 3 3 200 Ped W F 2,8 700 pfs Curves: in H2O Centrifugal module w. support bracket Pa kg Centrifugal fan 1000 2000 2000 4000 3000 4000 6000 5000 8000 6000 10000 7000 12000 1 8000 1 9000 14000 16000 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 94 ff. Inlet nozzle p. 158 ff. Guard grille p. 160 Electr. connection p. 166 ff. 93 EC centrifugal fans - RadiCal backward curved, O 630 R3G 630-RK57-31 (Centrifugal fan) O10.5(10x) O 5.2(6x) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery 0 8 85 10 850 +20 O 600 O 634 O 457 O 452 +2 O 472 -0.7 O 660 4x9 45 R129 O 200 O150 M6 (4x) 2.5 R3 R63.2 47.7 Depth of screw max. 16 mm 86.5 290 304 2 2 O 186 0.5 Connection line PVC AWG 18, 5 x crimped core-end sleeves 18 Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11(8x) O660 K3G 630-RK57-31 (Centrifugal module with support bracket) 15 367.5 2.5 415 3 549 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 94 EC centrifugal fans - RadiCal backward curved, O 630 R3G 630-RL94-21 (Centrifugal fan) O10.5(10x) O 5.2(6x) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery 0 8 85 10 850 +20 O 600 O 634 O 457 O 452 +2 O 472 -0.7 O 660 4x9 45 R129 O 200 O169 M6 (4x) 2.5 R3 R63.2 56.5 Depth of screw max. 16 mm 86.5 290 304 2 2 O 186 0.5 Connection line PVC AWG 18, 5 x crimped core-end sleeves 18 Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11(8x) O660 K3G 630-RL94-21 (Centrifugal module with support bracket) 15 367.5 2.5 424 3 549 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 95 EC centrifugal fans - RadiCal backward curved, O 630 R3G 630-RL95-01 (Centrifugal fan) O10.5(10x) O 5.2(6x) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery 0 8 85 10 850 +20 O 600 O 634 O 457 O 452 +2 O 472 -0.7 O 660 4x9 45 O 200 O169 M6 (4x) 2.5 R3 R129 R63.2 56.5 Depth of screw max. 16 mm 86.5 290 304 2 2 O 186 0.5 Connection line PVC AWG 18, 6 x crimped core-end sleeves 18 Connection line PVC AWG 22, 5 x crimped core-end sleeves O 11(4x) O660 K3G 630-RL95-01 (Centrifugal module with support bracket) 367.5 2.5 424 3 15 549 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 96 EC centrifugal fans - RadiCal backward curved, O 630 R3G 630-RA38-21 (Centrifugal fan) O10.5 (6x) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery M10 (6x) R63 O600 O634 O458 O452 O472 +2 -0.7 O660 0 6x6 R129 .5 R32 70 O232 -2 Depth of screw max. 25 mm Tightening torque 3.50.5 Nm 2 86.5 290 333 2 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm 18 O11(8x) O 660 O 605 K3G 630-RA38-21 (Centrifugal module with support bracket) 393 2 463 3 15 555 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 97 EC centrifugal fans - RadiCal backward curved, O 630 R3G 630-RA21-71 (Centrifugal fan) O10.5 (6x) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery M10 (6x) R63 O600 O634 O458 O452 O472 +2 -0.7 O660 0 6x6 R129 .5 R32 70 O232 -2 Depth of screw max. 25 mm Tightening torque 3.50.5 Nm 2 86.5 290 333 2 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm 18 O11(8x) O 660 O 605 K3G 630-RA21-71 (Centrifugal module with support bracket) 393 2 463 3 15 555 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 98 EC centrifugal fans - RadiCal backward curved, O 630 R3G 630-RB32-71 (Centrifugal fan) O10.5 (6x) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery M10 (6x) R63 O600 O634 O458 O452 O472 +2 -0.7 O660 0 6x6 R129 .5 R32 70 O232 -2 Depth of screw max. 25 mm Tightening torque 3.50.5 Nm 2 86.5 290 333 2 O2520.3 O275 Cable gland M20x1,5 (3x): Cable diameter min. 4 mm, max. 10 mm, Tightening torque 40.6 Nm 18 O11(8x) O 660 O 605 K3G 630-RB32-71 (Centrifugal module with support bracket) 393 2 463 3 15 555 750 800 Observe the correct mounting position! Install the support struts only as shown in the view! 99 100 AC centrifugal fans - RadiCal 101 AC centrifugal fans - RadiCal backward curved, O 133 Perm. amb. temp. Electrical connection B VAC Hz rpm W A F/VDB C p. 170 1~ 230 1~ 230 50 60 2700 3100 26 27 0,12 0,14 1,5 / 400 1,5 / 400 -25..+45 -25..+60 A1) Curves: Pa (1) Nominal data in operating point with maximum load and 230 VAC 280 in H2O subject to alterations A Capacitor M2E 042-CA Max. current draw(1) *2E 133 Max. input power(1) Motor Speed/rpm(1) Type Frequency Nominal data Nominal voltage Curve - Material: Housing: Plastic PA 6, fibreglass-reinforced Impeller: Plastic PA 6, fibreglass-reinforced Rotor: Coated in black - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 42, depending on installation and position in acc. to EN 60034-5 - Insulation class: "B" - Mounting position: any - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings 3 n rpm max. = 240 1,0 B 200 160 4 3 0,6 A 120 0,4 3 80 2 0,2 2 40 pfs 1 0 qV 20 40 40 60 80 80 120 100 160 1 120 200 50 Hz cfm m3/h 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 102 I A LWA dB(A) A 1 2750 25 0,11 58 A 2 2730 25 0,11 56 A 3 2700 26 0,12 53 A 4 2730 24 0,11 57 B 1 3200 25 0,13 62 B 2 3170 26 0,13 59 B 3 3100 27 0,14 57 B 4 3185 26 0,13 60 0,8 4 Ped W Mass of centrifugal module with support basket Motor protection: TOP wired internally Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Mass of centrifugal fan - - - - - Centrifugal fan kg Centrifugal module w. support basket kg R2E 133-RA03 -01 0,6 K2E 133-RA03 -01 0,8 Drawings p. 104 Inlet nozzle p. 158 Guard grille p. 160 Capacitor p. 161 Connection leads p. 162 Electr. connection p. 170 103 AC centrifugal fans - RadiCal backward curved, O 133 R2E 133-RA03-01 (Centrifugal fan) Depth of screw max. 4 mm 45 4x90 M4(4x) O118 O129 O87 O930.2 O133 56.51 O17 2 O4.5(4x) 55.51 48.5 20 0+ 6 85 1 0 1 O470.2 13 Accessory part: Inlet nozzle 09566-2-4013 not included in the standard scope of delivery Connection line, 3 x brass lead tips crimped 4 K2E 133-RA03-01 (Centrifugal module with support basket) 64 o165 O5 (4x) o1470.5 6 45 O19 50 O21 O19 0 50 104 0+ 45 85 1 0 20 6 .5 .5 O1 80 0 .5 Mounting dimensions: 105 AC centrifugal fans - RadiCal backward curved, O 190 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Capacitor Perm. amb. temp. Electrical connection VAC Hz rpm W A F/VDB C p. 170 1~ 230 1~ 230 50 60 2350 2500 52 65 0,23 0,29 1,5 / 400 1,5 / 400 -25..+65 -25..+75 A1) Curve Nominal voltage - Material: Housing: Plastic PA 6, fibreglass-reinforced Impeller: Plastic PA 6, fibreglass-reinforced Rotor: Coated in black - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "B" - Mounting position: any - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *2E 190 M2E 068-BF B 440 3 n rpm max. = 1,4 360 1,6 B 400 1,2 320 280 200 1,0 4 3 0,6 3 160 120 0,4 2 2 0,2 80 40 pfs 1 0 qV 50 100 100 150 200 200 300 250 400 300 500 50 Hz 1 cfm m3/h 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 106 I A LWA dB(A) A 1 2480 48 0,22 66 A 2 2440 49 0,22 63 A 3 2350 52 0,23 60 A 4 2435 50 0,22 62 B 1 2720 60 0,27 68 B 2 2645 62 0,27 66 B 3 2500 65 0,29 62 B 4 2615 63 0,27 65 4 A 0,8 240 Ped W 1,8 Curves: Pa (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations A Mass of centrifugal module with support basket Motor protection: TOP wired internally Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable (R2E) Connection leads: Plug system (K2E) Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: R2E: CCC, GOST K2E: CCC Mass of centrifugal fan - - - - - - - Centrifugal fan kg Centrifugal module w. support basket kg R2E 190-RA26 -05 1,3 K2E 190-RA26 -01 1,7 Drawings p. 108 Inlet nozzle p. 158 Guard grille p. 160 Capacitor p. 161 Connection leads p. 162 Electr. connection p. 170 107 AC centrifugal fans - RadiCal backward curved, O 190 R2E 190-RA26-05 (Centrifugal fan) 4x90 O4.5 (4x) 45 Depth of screw max. 5 mm M4 (4x) O158 O170 O125.5 450+20 O27 O132.8 O190 O80 2 6 8510 O580.2 62.5 68.51 Connection line, 4 x brass lead tips crimped 1.25 Accessory part: Inlet nozzle 09576-2-4013 not included in the standard scope of delivery 14 2 K2E 190-RA26-01 (Centrifugal module with support basket) o225 79 O5 (4x) o2040.5 6 45 Mounting dimensions: O2 6 6 0.5 O266 0.5 O2 44 0 PE L N + Capacitor Capacitor 108 Coded plug system AMP Universal-Mate-N-Lok Connector housing: AMP 350 780-1 4 x plug pin: AMP 926 885-1 Mating connector (not included in the standard scope of delivery) Connector housing: AMP 350 779-4 4 x female connector: AMP 926 884-1 .5 109 AC centrifugal fans - RadiCal backward curved, O 220 rpm *2E 220 M2E 068-BF *2E 220 A B 1~ 230 1~ 230 1~ 230 1~ 230 50 60 50 60 C M2E 068-CF D Electrical connection Hz Perm. amb. temp. Motor Capacitor Type Max. current draw(1) Speed/rpm(1) Nominal data Max. input power(1) Frequency VAC Curve Nominal voltage - Material: Housing: Plastic PA 6, fibreglass-reinforced Impeller: Plastic PA 6, fibreglass-reinforced Rotor: Coated in black - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "B" - Mounting position: any - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings W A F/VDB C p. 170 0,39 0,47 0,45 0,60 2,0 / 450 2,0 / 450 2,5 / 400 2,5 / 400 -25..+50 -25..+60 -25..+60 -25..+75 2100 88 2050 107 2500 102 2650 135 A1) (1) Nominal data in operating point with maximum load and 230 VAC 360 1,8 Pa 400 n rpm max. = 1,6 440 3 B 1,4 Curves: in H2O subject to alterations 320 1,2 A 280 160 1,0 4 0,8 200 4 3 3 0,6 240 0,4 120 2 40 0,2 80 pfs 1 0 qV 100 100 200 200 300 300 400 500 400 600 700 1 500 800 50 Hz cfm 900 m3/h 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 110 A1) Ped W I A LWA dB(A) A 1 2350 80 0,36 68 A 2 2240 86 0,38 62 A 3 2100 88 0,39 60 A 4 2185 86 0,38 63 B 1 2450 100 0,46 69 B 2 2220 105 0,46 62 B 3 2050 107 0,47 60 B 4 2165 105 0,46 63 Mass of centrifugal module with support basket Motor protection: TOP wired internally Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable (R2E) Connection leads: Plug system (K2E) Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: R2E 220-RA: VDE, CCC, GOST R2E 220-RB: CCC, GOST K2E: CCC Mass of centrifugal fan - - - - - - - kg R2E 220-RA38 -01 1,30 K2E 220-RA38 -01 2,00 R2E 220-RB06 -01 1,80 K2E 220-RB06 -01 2,40 600 3 n rpm max. = 400 1,6 500 2,0 D 4 C 4 1,2 300 Ped W I A LWA dB(A) A 1 2600 90 0,40 70 A 2 2575 95 0,43 66 A 3 2500 102 0,45 64 A 4 2580 95 0,42 67 B 1 2900 120 0,53 73 B 2 2790 130 0,56 68 B 3 2650 135 0,60 66 B 4 2795 125 0,55 69 3 200 0,8 3 2 100 0,4 2 1 1 pfs Curves: in H2O Centrifugal module w. support basket Pa kg Centrifugal fan 0 qV 100 200 200 300 400 400 600 500 800 500 cfm 1000 m3/h 50 Hz 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 112 Inlet nozzle p. 158 Guard grille p. 160 Capacitor p. 161 Connection leads p. 162 Electr. connection p. 170 111 AC centrifugal fans - RadiCal backward curved, O 220 R2E 220-RA38-01 / R2E 220-RB06-01 (Centrifugal fan) 4x90 O5.5 (6x) 45 Depth of screw max. 5 mm M4 (4x) O242 O252 O155 450+20 O27 O161 O220 O80 2 6 8510 O580.2 63.7 711 Connection line, 4 x brass lead tips crimped 0.8 Accessory part: Inlet nozzle 09609-2-4013 not included in the standard scope of delivery 21 2 K2E 220-RA38-01 / K2E 220-RB06-01 (Centrifugal module with support basket) o270 92 O5 (4x) o247.50.5 7 45 Mounting dimensions: O3 0 5 0.5 O305 0.5 O2 94 .5 PE L N + Capacitor Capacitor 112 Coded plug system AMP Universal-Mate-N-Lok Connector housing: AMP 350 780-1 4 x plug pin: AMP 926 885-1 Mating connector (not included in the standard scope of delivery) Connector housing: AMP 350 779-4 4 x female connector: AMP 926 884-1 0.5 113 AC centrifugal fans - RadiCal backward curved, O 225 50 60 W A F/VDB C p. 170 0,68 0,92 3,5 / 450 3,5 / 450 -25..+70 -25..+65 A1) 2500 155 2600 210 720 3 2,8 Curves: Pa (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations 1~ 230 1~ 230 Electrical connection B Perm. amb. temp. A rpm Capacitor M2E 068-DF Hz Max. current draw(1) *2E 225 VAC Max. input power(1) Motor Speed/rpm(1) Type Frequency Nominal data Nominal voltage Curve - Material: Housing: Plastic PA 6, fibreglass-reinforced Impeller: Plastic PA 6, fibreglass-reinforced Rotor: Coated in black - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "B" - Mounting position: any - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings max. = B 2,4 640 480 2,0 560 A 320 4 3 1,2 400 1,6 4 3 0,8 240 2 160 0,4 80 2 pfs 1 0 qV 100 200 200 400 300 400 600 500 800 600 1000 700 1200 50 Hz 1 cfm m3/h 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 114 n rpm Ped W I A LWA dB(A) A 1 2660 130 0,57 73 A 2 2575 145 0,64 72 A 3 2500 155 0,68 66 A 4 2590 145 0,63 69 B 1 2900 190 0,83 76 B 2 2735 205 0,89 73 B 3 2600 210 0,92 68 B 4 2750 200 0,88 71 Mass of centrifugal module with support basket Motor protection: TOP wired internally Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable (R2E) Connection leads: Plug system (K2E) Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: CCC Mass of centrifugal fan - - - - - - - Centrifugal fan R2E 225-RA92 -09 kg Centrifugal module w. support basket kg 2,30 K2E 225-RA92 -01 3,40 Drawings p. 116 Inlet nozzle p. 158 Guard grille p. 160 Capacitor p. 161 Connection leads p. 162 Electr. connection p. 170 115 AC centrifugal fans - RadiCal backward curved, O 225 R2E 225-RA92-09 (Centrifugal fan) 4x90 O4.5 (4x) 45 Depth of screw max. 5 mm M4 (4x) O210 O223 O146 450+20 O27 O153.5 O225 O80 2 6 8510 O580.2 88.4 991 Connection line, 4 x brass lead tips crimped 1.5 Accessory part: Inlet nozzle 96358-2-4013 not included in the standard scope of delivery 28 2 K2E 225-RA92-01 (Centrifugal module with support basket) o270 112 O5 (4x) o247.50.5 7 45 Mounting dimensions: O3 0 5 0.5 O305 0.5 O2 94 .5 PE L N + Capacitor Capacitor 116 Coded plug system AMP Universal-Mate-N-Lok Connector housing: AMP 350 780-1 4 x plug pin: AMP 926 885-1 Mating connector (not included in the standard scope of delivery) Connector housing: AMP 350 779-4 4 x female connector: AMP 926 884-1 0.5 117 AC centrifugal fans - RadiCal backward curved, O 250 rpm *2E 250 M2E 068-EC B 1~ 230 1~ 230 50 60 W A F/VDB C p. 170 0,93 1,25 5,0 / 400 5,0 / 400 -25..+70 -25..+30 A1) 2500 210 2450 285 900 max. = 3 3,6 Curves: Pa (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations A Electrical connection Hz Perm. amb. temp. Motor Capacitor Type Max. current draw(1) Speed/rpm(1) Nominal data Max. input power(1) Frequency VAC Curve Nominal voltage - Material: Housing: Plastic PA 6, fibreglass-reinforced Impeller: Plastic PA 6, fibreglass-reinforced Rotor: Coated in black - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "B" - Mounting position: any - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings 600 2,8 2,4 700 3,2 B 800 500 2,0 400 1,6 A 4 4 3 1,2 200 0,8 100 0,4 3 300 2 1 pfs 1 0 qV 100 200 200 400 300 400 600 500 800 600 1000 700 800 1200 1400 900 50 Hz 1600 cfm m3/h 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 118 n rpm Ped W I A LWA dB(A) A 1 2630 180 0,78 75 A 2 2525 205 0,91 70 A 3 2500 210 0,93 67 A 4 2585 190 0,83 72 B 1 3220 170 0,76 79 B 2 2485 275 1,20 71 B 3 2450 285 1,25 67 B 4 2650 260 1,15 74 Mass of centrifugal module with support basket Motor protection: TOP wired internally Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable (R2E) Connection leads: Plug system (K2E) Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: R2E: CCC Mass of centrifugal fan - - - - - - - Centrifugal fan R2E 250-RA50 -01 kg Centrifugal module w. support basket 2,90 K2E 250-RA50 -01 (2) kg 3,70 (2) Only applicable by 50 Hz Drawings p. 120 Inlet nozzle p. 158 Guard grille p. 160 Capacitor p. 161 Connection leads p. 162 Electr. connection p. 170 119 AC centrifugal fans - RadiCal backward curved, O 250 R2E 250-RA50-01 (Centrifugal fan) 4x90 O4.5 (4x) 45 Depth of screw max. 5 mm M4 (4x) O240 O255 O164.5 450+20 O27 O172.5 O250 O80 2 6 8510 O580.2 85 991 Connection line, 4 x brass lead tips crimped 1.5 Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery 31 2 K2E 250-RA50-01 (Centrifugal module with support basket) o300 108.5 O5 (4x) o2760.5 7 45 Mounting dimensions: O3 4 0 0.5 O340 0.5 O3 22 0 PE L N + Capacitor Capacitor 120 Coded plug system AMP Universal-Mate-N-Lok Connector housing: AMP 350 780-1 4 x plug pin: AMP 926 885-1 Mating connector (not included in the standard scope of delivery) Connector housing: AMP 350 779-4 4 x female connector: AMP 926 884-1 .5 121 AC centrifugal fans - RadiCal backward curved, O 250 rpm *2E 250 M2E 074-EI B 1~ 230 1~ 230 50 60 W A F/VDB C p. 170 1,10 1,71 5,0 / 450 5,0 / 450 -25..+70 -25..+55 A1) 2750 250 3100 390 900 max. = 3 3,6 Curves: Pa (1) Nominal data in operating point with maximum load and 230 VAC in H2O subject to alterations A Electrical connection Hz Perm. amb. temp. Motor Capacitor Type Max. current draw(1) Speed/rpm(1) Nominal data Max. input power(1) Frequency VAC Curve Nominal voltage - Material: Impeller: Plastic PA 6, fibreglass-reinforced Rotor: Coated in black - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings 700 2,8 600 2,4 3,2 B 800 4 A 1,2 2,0 300 200 0,8 400 100 0,4 500 1,6 4 3 3 2 2 1 pfs 1 0 qV 100 200 200 400 300 400 600 500 800 600 1000 700 800 900 1200 1400 50 Hz 1600 cfm m3/h 60 Hz Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 122 n rpm Ped W I A LWA dB(A) A 1 2800 215 0,95 78 A 2 2790 235 1,05 74 A 3 2750 250 1,10 71 A 4 2800 230 1,00 74 B 1 3200 345 1,50 81 B 2 3150 370 1,60 77 B 3 3100 390 1,71 73 B 4 3140 370 1,60 79 Motor protection: TOP wired internally Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: VDE, CURUS on request Mass of centrifugal fan - - - - - - Centrifugal fan R2E 250-RB06 -01 kg 4,10 Drawings p. 124 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 170 123 AC centrifugal fans - RadiCal backward curved, O 250 R2E 250-RB06-01 (Centrifugal fan) M6(4x) R 28 6 0 1 2 Accessory part: Inlet nozzle 96359-2-4013 not included in the standard scope of delivery 85 +20 0 O90 0.2 1.5 31 45 85 108 1 O240 O255 O164.5 O101 O75 O172.5 0.3 O250 5 124 Depth of screw max. 10 mm O4.5(4x) 117.8 Connection line, 4 x brass lead tips crimped 125 AC centrifugal fans - RadiCal backward curved, O 280 rpm *4E 280 M4E 068-DF *2D 280 M2D 074-GA A B 1~ 230 1~ 230 3~ 400 50 60 50 C Electrical connection Hz Perm. amb. temp. Motor Capacitor Type Max. current draw(1) Speed/rpm(1) Nominal data Max. input power(1) Frequency VAC Curve Nominal voltage - Material: Impeller: Plastic PP Rotor: Coated in black - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: A B "B"; C "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings W A F/VDB C p. 170 / 171 0,40 0,55 0,91 2,5 / 400 2,5 / 400 --- -25..+65 -25..+55 -25..+50 1320 90 1400 125 2500 570 D2) (1) Nominal data in operating point with maximum load and 230 or 400 VAC Pa 700 3,2 800 3 n rpm max. = 1,6 2,0 400 300 1,2 500 3 2 0,8 A 200 4 0,4 3 100 pfs 2 0 qV I A LWA dB(A) A 1 1380 73 0,32 66 A 2 1340 85 0,37 61 A 3 1320 90 0,40 55 A 4 1340 84 0,37 57 C 1 2640 440 0,73 84 C 2 2555 520 0,84 79 C 3 2500 570 0,91 73 C 4 2540 530 0,84 74 2,4 4 600 Ped W C 2,8 Curves: (50 Hz) in H2O subject to alterations 200 400 400 600 800 800 1200 1 1000 1600 1 1200 2000 1400 2400 1600 cfm 2800 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 126 A1) Motor protection: A B TOP wired internally; C Connection for external TOP Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: A B Axial; C Variable Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: R4E: CCC R2D: VDE, CURUS on request Mass of centrifugal fan - - - - - - Centrifugal fan kg R4E 280-RA28 -05 R2D 280-RB06 -01 (3) 2,50 5,40 280 in H2O 3 max. = B 1,1 300 200 0,8 180 0,7 220 0,9 240 1,0 260 4 160 100 80 I A LWA dB(A) B 1 1550 105 0,45 68 B 2 1450 120 0,50 62 B 3 1400 125 0,55 57 B 4 1470 115 0,50 60 0,6 0,5 0,4 120 Ped W 3 2 0,3 140 n rpm 40 20 0,2 60 0,1 Curves: (60 Hz) Pa (3) ErP 2013 1 pfs (2) ErP 2015 (2) 0 qV 100 200 200 400 300 400 600 500 800 600 1000 700 800 1200 1400 900 1000 1600 cfm 1800 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 128 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 170 /171 127 AC centrifugal fans - RadiCal backward curved, O 280 R4E 280-RA28-05 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4(4x) R1 7 R53 O260 O280 O180 O80 O27 O187.5 O294 2 6 1.25 46 10 0 +2 O580.2 85 0 45 127 132 1 Connection line PVC 4G 0,5 mm2, 4 x brass lead tips crimped 8 O4.5(4x) R2D 280-RB06-01 (Centrifugal fan) Accessory part: Inlet nozzle 28000-2-4013 not included in the standard scope of delivery Depth of screw max. 10 mm M6(4x) 7 R1 R33 O260 O280 O179.6 O176.7 O187.5 0.3 O294 O101 O75 R53 5 0 0 +2 45 128 0 1 8 85 127 1651 6 1.25 46 O900.2 Connection line PFA 9G 0,5 mm2, 9 x brass lead tips crimped 129 AC centrifugal fans - RadiCal backward curved, O 310 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Capacitor Perm. amb. temp. Electrical connection VAC Hz rpm W A F/VDB C p. 170 / 171 1~ 230 1~ 230 1~ 230 1~ 230 3~ 400 3~ 400 50 60 50 60 50 60 890 1000 1325 1380 1380 1550 55 69 137 185 145 205 0,25 0,31 0,62 0,82 0,35 0,37 1,5 / 450 1,5 / 450 4,0 / 400 4,0 / 400 ----- -25..+60 -25..+60 -25..+60 -25..+40 -25..+55 -25..+55 Curve Nominal voltage - Material: Impeller: Plastic PP Rotor: Coated in black - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "B" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *6E 310 M6E 068-EC *4E 310 A B C M4E 068-EC *4D 310 D E M4D 068-EC Pa Curves: (50 Hz) 280 E 3 D2) n rpm max. = 200 180 0,9 4 0,8 220 4 C 3 80 0,5 4 0,4 100 2 2 3 2 0,1 20 0,2 60 40 pfs 1 0 qV I A LWA dB(A) A 1 930 48 0,23 57 A 2 910 52 0,24 53 A 3 890 55 0,25 46 A 4 910 52 0,24 47 C 1 1390 110 0,50 66 C 2 1345 130 0,58 61 C 3 1325 137 0,62 56 C 4 1355 125 0,57 58 E 1 1425 110 0,32 67 E 2 1395 130 0,33 62 E 3 1380 145 0,35 56 E 4 1395 130 0,33 59 A 0,3 120 0,6 160 140 Ped W 3 0,7 240 1,0 260 200 200 400 400 600 600 800 1000 800 1200 1400 1 1 1000 1600 1800 1200 cfm 2000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 130 A1) (1) Nominal data in operating point with maximum load and 230 or 400 VAC 1,1 in H2O subject to alterations F A1) Motor protection: A B C D TOP wired internally; E F Connection for external TOP Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Axial Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: VDE, CURUS on request Mass of centrifugal fan - - - - - - 3,40 R4E 310-RA06 -01 3,40 R4D 310-RA18 -01 3,40 400 3 n rpm max. = Ped W I A LWA dB(A) 1,4 F 360 320 1,2 4 D B 1 1085 60 0,26 60 B 2 1035 65 0,29 56 B 3 1000 69 0,31 49 B 4 1040 65 0,28 52 D 1 1580 150 0,64 69 D 2 1455 175 0,77 63 D 3 1380 185 0,82 61 D 4 1470 170 0,75 62 F 1 1635 150 0,30 70 F 2 1580 185 0,34 65 F 3 1550 205 0,37 61 F 4 1585 180 0,34 66 280 4 200 1,0 3 0,8 240 3 160 0,6 B 4 2 120 2 0,4 3 80 40 2 1 pfs Curves: (60 Hz) Pa R6E 310-RA04 -01 in H2O kg 0,2 Centrifugal fan 0 qV 200 200 400 400 600 600 800 1 1000 1200 1 1400 cfm 800 1000 1200 1400 1600 1800 2000 2200 2400 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 132 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 170 /171 131 AC centrifugal fans - RadiCal backward curved, O 310 R6E 310-RA04-01 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4(4x) R2 R45.4 O280 O300 O193 O191.5 O204 O325.5 O27 O80 4.3 R71.1 2 45 0 +2 0 154 1 O580.2 8 6 10 85 1.5 58.5 141.5 Connection line PVC 4G 0,5 mm2, 4 x brass lead tips crimped R4E 310-RA06-01 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4(4x) R2 R45.4 O280 O300 O193 O191.5 O204 O325.5 O27 O80 4.3 R71.1 2 45 0 +2 0 154 1 O580.2 6 10 85 1.5 58.5 141.5 8 Connection line PVC 4G 0,5 mm2, 4 x brass lead tips crimped 132 AC centrifugal fans - RadiCal backward curved, O 310 R4D 310-RA18-01 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 31000-2-4013 not included in the standard scope of delivery Depth of screw max. 5 mm M4(4x) R45.4 O280 O300 O193 O191.5 O204 O325.5 O27 O80 4.3 R2 R71.1 2 0 +2 0 45 154 1 8 O580.2 6 10 85 1.5 58.5 141.5 Connection line PVC 6G 0,5 mm2, 6 x brass lead tips crimped 133 AC centrifugal fans - RadiCal backward curved, O 355 M4E 074-GA *4D 355 D M4D 074-GA p. 170 / 171 830 85 775 105 1330 270 0,37 0,46 1,18 2,0 / 400 2,0 / 400 6,0 / 400 -25..+60 -25..+50 -25..+60 1390 270 1550 400 0,72 0,78 ----- -25..+60 -25..+40 Hz rpm 1~ 230 1~ 230 1~ 230 50 60 50 3~ 400 3~ 400 50 60 A1) A1) D2) 360 3 D 1,4 Curves: (50 Hz) Pa (1) Nominal data in operating point with maximum load and 230 or 400 VAC in H2O subject to alterations E Electrical connection C Perm. amb. temp. B Capacitor *4E 355 A Max. current draw(1) M6E 074-DF C Speed/rpm(1) *6E 355 F/VDB Frequency Motor A Nominal voltage Type W VAC Curve Nominal data Max. input power(1) - Material: Impeller: Plastic PP Rotor: Coated in black - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 44, depending on installation and position in acc. to EN 60034-5 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings n rpm max. = 1,2 320 4 C 1,0 240 3 160 0,6 200 0,8 3 2 2 0,4 4 80 0,2 40 3 2 pfs 1 0 qV 200 400 500 600 1000 800 1500 1000 1200 2000 1 1 1400 2500 1600 1800 3000 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 134 LWA dB(A) 1 905 70 0,32 60 A 2 870 80 0,35 55 A 3 830 85 0,37 48 A 4 845 85 0,36 48 C 1 1405 200 0,89 72 C 2 1375 230 1,00 66 C 3 1330 270 1,18 61 C 4 1360 245 1,05 63 D 1 1425 205 0,67 72 D 2 1405 240 0,69 67 D 3 1390 270 0,72 62 D 4 1395 265 0,70 62 A 120 I A A 4 280 Ped W Motor protection: A B C TOP wired internally; D E Connection for external TOP Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: VDE, CURUS on request Mass of centrifugal fan - - - - - - 4,20 R4E 355-RB10 -01 5,60 R4D 355-RB10 -01 5,60 3 480 360 1,8 1,6 400 1,2 320 280 160 I A LWA dB(A) B 1 985 96 0,44 62 B 2 875 100 0,44 55 B 3 775 105 0,46 48 B 4 805 105 0,45 48 E 1 1635 295 0,64 75 E 2 1590 355 0,72 70 E 3 1550 400 0,78 66 E 4 1555 390 0,76 65 1,0 0,8 200 3 B 0,6 240 Ped W 4 1,4 440 n rpm max. = E 2 0,4 120 4 80 40 3 2 1 pfs Curves: (60 Hz) Pa R6E 355-RB20 -01 2,0 in H2O kg 0,2 Centrifugal fan 0 qV 400 500 800 1000 1500 1 1200 2000 1600 2500 2000 3000 3500 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 136 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 170 /171 135 AC centrifugal fans - RadiCal backward curved, O 355 R6E 355-RB20-01 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery Depth of screw max. 10 mm M6(4x) O325 O350 O227.1 O223.3 +1.5 O237 -0.4 O372.5 O101 O75 2.5 R43.5 R2 R69.5 5 6 0 1 0 +2 0 O90 0.2 85 162 190 1.5 45 1.5 60 Connection line silicone 4G 0,5 mm2, 4 x brass lead tips crimped 10 R4E 355-RB10-01 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery M6(4x) R43.5 O325 O350 O227.1 O223.3 O237 O372.5 O101 O75 R69.5 2.5 R2 5 Depth of screw max. 10 mm 0 +2 0 45 6 0 1 90 0.2 Connection line silicone 4G 0,5 mm2, 4 x brass lead tips crimped 10 136 85 1.5 60 161.5 190 1.5 AC centrifugal fans - RadiCal backward curved, O 355 R4D 355-RB10-01 (Centrifugal fan) O4.5(4x) Accessory part: Inlet nozzle 35500-2-4013 not included in the standard scope of delivery M6(4x) R43.5 O325 O350 O227.1 O223.3 O237 O372.5 O101 O75 R69.5 2.5 R2 5 Depth of screw max. 10 mm 20 0+ 45 6 0 1 85 1.5 60 161.5 190 1.5 90 0.2 Connection line silicone 9G 0,5 mm2, 9 x brass lead tips crimped 10 137 AC centrifugal fans - RadiCal backward curved, O 400 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Capacitor Perm. amb. temp. Electrical connection VAC Hz rpm W A F/VDB C p. 170 / 171 1~ 230 1~ 230 1~ 230 1~ 230 3~ 400 3~ 400 50 60 50 60 50 60 880 970 1340 1430 1400 1580 155 215 470 650 515 770 0,68 0,95 2,33 3,00 1,19 1,35 5,0 / 450 5,0 / 450 9,0 / 400 9,0 / 400 ----- -40..+60 -40..+60 -40..+60 -40..+45 -40..+60 -40..+40 Curve Nominal voltage - Material: Impeller: Plastic PP Rotor: Coated in black - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Any - Condensate discharges: None - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *6E 400 M6E 094-FA *4E 400 M4E 094-HA *4D 400 M4D 094-HA B C D E F Pa 3 A2a) F1a) 400 n rpm max. = E 1,6 Curves: (50 Hz) 4 4 200 3 0,8 300 1,2 C 3 2 2 100 0,4 3 2 pfs 1 0 qV 500 1000 1000 1500 2000 1 1 2000 3000 2500 4000 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Ped W I A LWA dB(A) A 1 915 130 0,58 69 A 2 895 145 0,64 62 A 3 880 155 0,68 55 A 4 895 145 0,63 55 C 1 1395 370 1,95 --- C 2 1360 435 2,20 --- C 3 1340 470 2,33 --- C 4 1380 400 2,05 --- E 1 1430 405 1,10 81 E 2 1410 480 1,15 75 E 3 1400 515 1,19 67 E 4 1410 475 1,15 67 A 4 138 A2a) (1) Nominal data in operating point with maximum load and 230 or 400 VAC in H2O subject to alterations A Motor protection: Connection for external TOP Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60335-1, CE Approvals: A B C D CCC Mass of centrifugal fan - - - - - - 7,40 R4E 400-RO09 -01 8,50 R4D 400-RO22 -01 8,80 3 max. = n rpm Ped W I A LWA dB(A) 2,4 F 600 500 2,0 400 1,6 4 4 D 3 200 B 4 0,8 300 1,2 3 2 2 B 1 1055 195 0,85 70 B 2 1005 210 0,91 64 B 3 970 215 0,95 57 B 4 1020 205 0,90 59 D 1 1585 525 2,35 --- D 2 1470 625 2,90 --- D 3 1430 650 3,00 --- D 4 1535 575 2,60 --- F 1 1645 600 1,10 85 F 2 1605 715 1,25 79 F 3 1580 770 1,35 72 F 4 1605 700 1,25 73 3 100 2 pfs Curves: (60 Hz) Pa R6E 400-RN06 -01 in H2O kg 0,4 Centrifugal fan 0 qV 500 1000 1000 1 2000 1500 2000 3000 2500 4000 1 1 3000 cfm 5000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 140 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 170 /171 139 AC centrifugal fans - RadiCal backward curved, O 400 O 4.5 (4x) R6E 400-RN06-01 (Centrifugal fan) Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery Depth of screw max. 12 mm M6 (4x) 4x9 0 5.5 O 345 O 370 O 257 O 266 0.5 O420 O130 O100 45 R 90 0 R5 0 1 85 +20 0 60 6 1.5 66 182 1941 O1150.2 Connection line silicone 6G 0,5 mm2, 6 x brass lead tips crimped 10 O 4.5 (4x) R4E 400-RO09-01 (Centrifugal fan) Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery Depth of screw max. 12 mm M6 (4x) 4x9 0 5.5 O 345 O 370 O 257 O 266 0.5 O420 O130 O100 45 R90 0 1 85 +20 0 60 1.5 66 182 1941 10 140 0 R5 6 O1150.2 Connection line silicone 6G 0,5 mm2, 6 x brass lead tips crimped AC centrifugal fans - RadiCal backward curved, O 400 R4D 400-RO22-01 (Centrifugal fan) O 4.5 (4x) Accessory part: Inlet nozzle 54476-2-4013 not included in the standard scope of delivery Depth of screw max. 12 mm M6 (4x) 4x9 0 5.5 O 345 O 370 O 257 O 266 0.5 O420 O130 O100 45 R 90 0 R5 6 0 1 85 +20 0 60 1.5 66 182 1941 10 O1150.2 Connection line silicone 9G 0,5 mm2, 9 x brass lead tips crimped 141 AC centrifugal fans - RadiCal backward curved, O 450 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Capacitor Perm. amb. temp. Electrical connection VAC Hz rpm W A F/VDB C p. 170 / 171 A 1~ 230 50 940 285 1,35 8,0 / 450 -40..+60 B 1~ 230 50 1260 690 3,10 14,0 / 450 -40..+55 C 3~ 400 50 1350 710 1,45 -40..+60 Curve Nominal voltage - Material: Impeller: Plastic PP Rotor: Cast in aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Shaft horizontal or rotor om bottom, rotor on top on request - Condensate discharges: Rotor-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *6E 450 M6E 110-EF *4E 450 M4E 110-GF *4D 450 M4D 110-GF A1) D2) Curves: (50 Hz) Pa (1) Nominal data in operating point with maximum load and 230 or 400 VAC in H2O subject to alterations --- A1) 3 n rpm max. = 2,0 C 500 4 B 1,2 3 300 3 A 4 0,8 200 2 3 2 0,4 100 2 pfs 1 0 qV 500 1000 1000 2000 1500 2000 3000 2500 4000 1 1 3000 5000 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 142 I A LWA dB(A) A 1 960 230 1,15 68 A 2 950 260 1,25 65 A 3 940 285 1,35 62 A 4 945 270 1,30 63 B 1 1365 545 2,40 77 B 2 1310 630 2,75 74 B 3 1260 690 3,10 69 B 4 1295 650 2,85 71 C 1 1405 495 1,15 77 C 2 1370 645 1,30 75 C 3 1350 710 1,45 70 C 4 1370 650 1,30 73 4 1,6 300 Ped W Motor protection: Connection for external TOP Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Variable Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: A B EN 61800-5-1, CE C EN 60034, CE Approvals: VDE, CCC, GOST, UL, CSA Mass of centrifugal fan - - - - - - Centrifugal fan kg R6E 450-RG01 -01 12,0 R4E 450-RH01 -01 12,0 R4D 450-RH01 -01 9,40 Drawings p. 144 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 170 /171 143 AC centrifugal fans - RadiCal backward curved, O 450 R6E 450-RG01-01 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery O9(6x) 240 3 O 425 O 450 O 292 O 286.7 O 142 O 130 O 100 0 4x90 O300 0.5 O 485 R 40 R2 R 50 O 438.9 M6 (4x) 45 5.5 6 Depth of screw max. 12 mm 10 80 +20 800 3 50 140 218 O1150.3 Connection line silicone 6G 0,5 mm2, 6 x brass lead tips crimped 10 R4E 450-RH01-01 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery O9(6x) 240 3 5.5 R 40 O 425 O 450 O 292 O 286.7 O300 0.5 O 485 O 142 O 130 O 100 0 4x90 O 438.9 45 R2 10 80 +20 800 3 50 140 218 10 144 M6 (4x) R50 6 Depth of screw max. 12 mm O1150.3 Connection line silicone 6G 0,75 mm2, 6 x brass lead tips crimped AC centrifugal fans - RadiCal backward curved, O 450 R4D 450-RH01-01 (Centrifugal fan) Accessory part: Inlet nozzle 45901-2-2943 not included in the standard scope of delivery O9(6x) 240 3 5.5 45 0 O 425 O 450 O 292 O 286.7 O 142 O 130 O 100 O300 0.5 O 485 R 40 R2 4x90 O 438.9 M6 (4x) R 50 6 Depth of screw max. 12 mm 10 80 +20 800 3 50 140 218 10 O1150.3 Connection line silicone 9G 0,75 mm2, 9 x brass lead tips crimped 145 AC centrifugal fans - RadiCal backward curved, O 500 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Capacitor Perm. amb. temp. Electrical connection VAC Hz rpm W A F/VDB C p. 171 3~ 400 50 1370 Curve Nominal voltage - Material: Impeller: Plastic PP Rotor: Cast in aluminium - Number of blades: 7 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Any - Condensate discharges: Rotor- and stator-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *4D 500 M4D 138-HF 1520 2,91 --- -40..+70 Pa 800 3 max. = n rpm Ped W I A LWA dB(A) A 700 2,8 Curves: (50 Hz) 2,4 400 1,6 500 300 1,2 600 2,0 4 3 200 0,8 100 0,4 2 pfs 1 0 qV 1000 1000 2000 2000 3000 3000 4000 5000 4000 6000 7000 5000 8000 9000 cfm m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 146 D2) (1) Nominal data in operating point with maximum load and 400 VAC in H2O subject to alterations A A 1 1410 1125 2,45 81 A 2 1390 1350 2,70 77 A 3 1370 1520 2,91 73 A 4 1380 1385 2,75 73 Motor protection: Connection for external TOP Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Lateral Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60034, EN 61800-5-1, CE Approvals: VDE, GOST Mass of centrifugal fan - - - - - - Centrifugal fan R4D 500-RA03 -01 kg 21,5 Drawings p. 148 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 171 147 AC centrifugal fans - RadiCal backward curved, O 500 R4D 500-RA03-01 (Centrifugal fan) Depth of screw max. 18 mm M10 (8x) 22.5 8x O 9 (6x) Accessory part: Inlet nozzle 50901-2-2943 not included in the standard scope of delivery 45 5.5 R2 O 445 O 470 6 8510 1000+20 O320 O 334.5 0.5 O 525 O190 O140 R87 R49 8 3.5 75 O 1620.2 227 295.5 2 148 12 Connection line halogen-free 9 x 0,75 mm2, 9 x brass lead tips crimped 149 AC centrifugal fans - RadiCal backward curved, O 560 W A 3~ 400 3~ 400 50 60 1390 1560 Electrical connection rpm Perm. amb. temp. B Hz F/VDB C p. 171 -40..+60 -40..+40 D2) 1950 3,98 2990 5,16 ----- Curves: (50 Hz) Pa (1) Nominal data in operating point with maximum load and 400 VAC 1000 4,0 in H2O subject to alterations A VAC Capacitor M4D 138-LA Max. current draw(1) *4D 560 Max. input power(1) Motor Speed/rpm(1) Type Frequency Nominal data Nominal voltage Curve - Material: Impeller: Plastic PP Rotor: Cast in aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: IP 54 - Insulation class: "F" - Mounting position: Any - Condensate discharges: Rotor- and stator-side - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings 3 B max. = 3,2 A 600 2,4 4 3 400 1,6 3 2 pfs 200 0,8 2 0 qV 1000 2000 2000 4000 3000 4000 6000 5000 8000 6000 10000 1 7000 1 cfm 12000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 150 Ped W I A LWA dB(A) A 1 1425 1475 3,45 85 A 2 1405 1780 3,75 81 A 3 1390 1950 3,98 78 A 4 1400 1850 3,85 79 B 1 1635 2275 4,05 88 B 2 1590 2730 4,75 84 B 3 1560 2990 5,16 81 B 4 1585 2785 4,80 83 4 800 n rpm Motor protection: Connection for external TOP Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Lateral Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60034, EN 61800-5-1, CE Approvals: VDE, GOST Mass of centrifugal fan - - - - - - Centrifugal fan R4D 560-RB03 -01 kg 25,5 Drawings p. 152 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 171 151 AC centrifugal fans - RadiCal backward curved, O 560 R4D 560-RB03-01 (Centrifugal fan) O9 (6x) Accessory part: Inlet nozzle 54482-2-4013 not included in the standard scope of delivery Depth of screw max. 18 mm M10(8x) 45 8x 5.5 R 50 O 540 O 565 O 407 1000+20 8510 O190 O140 O 4180.7 O 567 22.5 83.5 253 2892 18 152 1.5 O1620.2 Connection line halogen-free 9 x 0,5 mm2, 9 x brass lead tips crimped 153 AC centrifugal fans - RadiCal backward curved, O 630 Frequency Speed/rpm(1) Max. input power(1) Max. current draw(1) Capacitor Perm. amb. temp. Electrical connection VAC Hz rpm W A F/VDB C p. 171 3~ 400 3~ 400 3~ 400 50 60 50 880 940 1345 Curve Nominal voltage - Material: Impeller: Plastic PP Rotor: Cast in aluminium - Number of blades: 6 - Direction of rotation: Clockwise, seen on rotor - Type of protection: A B IP 54, C IP 20 - Insulation class: "F" - Mounting position: Any - Condensate discharges: A B Rotor- and stator-side, - Mode of operation: Continuous operation (S1) - Bearings: Maintenance-free ball bearings Nominal data Type Motor *6D 630 M6D 138-HF *4D 630 M4D 138-LA A B C 1030 2,20 1440 2,81 3570 6,63 ------- -40..+60 -40..+60 -40..+40 Rotor-side D2) D2) (1) Nominal data in operating point with maximum load and 400 VAC = Pa 700 3,2 3 800 n rpm max. C 4 2,8 Curves: (50 Hz) in H2O subject to alterations 400 2,0 500 1,6 600 2,4 3 A 2 4 1,2 300 0,8 3 200 0,4 2 100 pfs 1 0 qV 2000 2000 4000 4000 6000 6000 8000 10000 1 8000 12000 14000 10000 cfm 16000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. 154 C Ped W I A LWA dB(A) A 1 925 735 1,85 79 A 2 895 935 2,10 73 A 3 880 1030 2,20 71 A 4 885 995 2,15 72 C 1 1400 2570 5,15 90 C 2 1360 3315 6,25 84 C 3 1345 3570 6,63 81 C 4 1350 3395 6,35 83 Motor protection: Connection for external TOP Touch current: <= 3,5 mA acc. to IEC 60990 (test circuit, illustration 4) Cable exit: Lateral Protection class: I (if customer has provided connection for protective earth) Product conforming to standards: EN 60034, EN 61800-5-1, CE Approvals: VDE, GOST Mass of centrifugal fan - - - - - - 25,0 R4D 630-RB15 -01 28,0 480 3 B max. = 400 1,6 440 4 360 n rpm Ped W I A LWA dB(A) B 1 1030 1090 2,20 83 B 2 970 1340 2,65 75 B 3 940 1440 2,81 72 B 4 945 1410 2,75 73 280 1,2 320 3 240 200 160 2 0,4 120 80 40 1 pfs Curves: (60 Hz) Pa R6D 630-RA07 -01 in H2O kg 0,8 Centrifugal fan 0 qV 1000 2000 2000 3000 4000 4000 6000 5000 8000 6000 10000 7000 cfm 12000 m3/h Air performance measured as per: ISO 5801, Installation category A, with ebm-papst inlet nozzle without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed information see page 172 ff. Drawings p. 156 Inlet nozzle p. 158 ff. Guard grille p. 160 Capacitor p. 161 Electr. connection p. 171 155 AC centrifugal fans - RadiCal backward curved, O 630 R6D 630-RA07-01 (Centrifugal fan) O10.5 (6x) Accessory part: Depth of screw max. 18 mm Inlet nozzle 63300-2-4013 22,5 not included in the standard M10 (8x) scope of delivery 45 8x O600 O634 R63.2 6 85 10 1000 +20 O 457 O 452 O 472 0.7 O 660 O605 O190 O140 R129 .5 R32 5.5 2 86.5 290 3332 O 162 0.2 18 Connection line halogen-free 9 x 0,75 mm2, 9 x brass lead tips crimped O10.5 (6x) R4D 630-RB15-01 (Centrifugal fan) Accessory part: Inlet nozzle 63300-2-4013 not included in the standard scope of delivery M10 (8x) Depth of screw max. 18 mm 22,5 45 8x O600 O634 R63.2 6 85 10 1000 +20 O 457 O 452 O 472 0.7 O 660 O605 O190 O140 .5 R129 R32 5.5 2 86.5 290 3332 156 18 O 162 0.2 Connection line halogen-free 9 x 0,75 mm2, 9 x brass lead tips crimped 157 Inlet nozzles Vers. 1 Vers. 2 - Material: galvanised sheet steel 6x6 0 90 4x Inlet nozzles without measuring device for backward curved centrifugal fans Part no. Size Vers. Dimensions 09566-2-4013 133 1 see corresponding product page 09576-2-4013 190 1 see corresponding product page 09609-2-4013 220 2 see corresponding product page 96358-2-4013 225 1 see corresponding product page 96359-2-4013 250 1 see corresponding product page 28000-2-4013 280 1 see corresponding product page 31000-2-4013 310 1 see corresponding product page 35500-2-4013 355 1 see corresponding product page 54476-2-4013 400 1 see corresponding product page 45901-2-2943 * 450 2 see corresponding product page 50901-2-2943 * 500 2 see corresponding product page 54482-2-4013 560 2 see corresponding product page 63300-2-4013 630 2 see corresponding product page subject to alterations * Material: Plastic ABS Effects of installation space Curve: might be reduced. 1,00 When mounting our product in a rectangular box, air performance 0,99 B Formula: dh = 2 x B x H / (B + H) B = Width of box H = Height of box D = Outer diameter of the fan 158 0,96 0,95 0,94 0,93 0,92 Correction factor for air flow dh = Hydraulic diameter D D 0,5xD H 0,97 0,98 D 1,4 1,6 1,8 Hydraulic diameter dh/D 2,0 2,2 2,4 2,6 2,8 Inlet nozzles with measuring device - Material: galvanised sheet steel With piezometer ring Inlet nozzles with measuring device to determine air flow for backward curved centrifugal fans Part no. Size k-value Dimensions 96400-2-4013 250 60 see corresponding product page 28003-2-4013 280 77 see corresponding product page 31003-2-4013 310 93 see corresponding product page 35503-2-4013 355 128 see corresponding product page 54501-2-4013 400 180 see corresponding product page 45910-2-2943 * 450 190 see corresponding product page 50920-2-2943 * 500 260 see corresponding product page 54492-2-4013 560 405 see corresponding product page 63310-2-4013 630 515 see corresponding product page subject to alterations * Material: Plastic ABS Air flow determination qV in [m3/h] und p in [Pa] If constant air flow is to be controlled to, then the nozzle pressure has to be kept constant: p = qV2 : k2 p qV = k . p 0,5xD D The differential pressure approach compares the static pressure before the inlet nozzle with the static pressure inside the inlet nozzle. Air flow can be calculated on the basis of the differential pressure (difference in pressure of the static pressures) in keeping with the following equation: k takes into account the specific nozzle characteristics. Differences in static pressure are measured in 1/4 measuring point(s) along the circumference of the inlet nozzle. Connection on the customer side is acomplished via a pre-mounted T tube connector. This tube connector is suited for pneumatic hoses with an internal diameter of 4 mm. 159 Air intake guard grilles Vers. 1 Vers. 2 - Material: steel wire, plastic coated a Od Od a e b e b Air intake guard grilles for backward curved centrifugal fans (according to EN ISO 13857) Part no. Size Vers. a b d e Strut pitch 78128-2-4039 250 1 240 5,4 208 2,4 4 x 90 78129-2-4039 280 1 260 4,5 210 2,8 4 x 90 78130-2-4039 310 1 280 4,5 230 2,8 4 x 90 78131-2-4039 355 1 325 4,5 250 2,8 4 x 90 78132-2-4039 400 1 345 4,5 310 2,8 4 x 90 78136-2-4039 450 2 425 8,5 350 3,8 3 x 120 78139-2-4039 500 2 445 8,5 410 3,8 3 x 120 78138-2-4039 630 2 600 8,5 490 3,8 3 x 120 The tab le has b een cha to the p nged w rinted e ith resp dition o ect f the ca talogue . subject to alterations a b - Material: PA plastic 6, fibreglass-reinforced Guard grille for suction side for compact centrifugal modules Part no. Size a b 13351-2-2929 133 94,1 7,7 19051-2-2929 190 133,0 9,0 22051-2-2929 220 166,0 8,7 22551-2-2929 225 158,0 8,7 25051-2-2929 250 177,0 9,7 subject to alterations 160 Capacitors 10 c - Material: Plastic cap, aluminium cup - Designation: FPU or P2 according to IEC 252 (non-flammable, non-explosive, circuit-breaking) - Approval: VDE according to DIN EN 60252 (VDE 0560/8) - Calculated life time: 420 V; -25 to +85C; 30,000 hrs; class A 470 V; -25 to +85C; 10,000 hrs; class B 500 V; -25 to +85C; 3,000 hrs; class C Oa M8 O a + 3,5 b 7 1 35 +5 235 +10 -5 MKP motor capacitors FPU or P2 (with fuse) Part no. Capacity a b (max.) c (max.) 02155-4-7320 1,5 F 25,0 77,0 92,0 02156-4-7320 2,0 F 25,0 77,0 92,0 02159-4-7320 2,5 F 30,0 71,0 92,0 02179-4-7320 3,5 F 30,0 75,0 82,0 02161-4-7320 4,0 F 25-30 104,0 135,0 02162-4-7320 5,0 F 25-30 104,0 113,0 02163-4-7320 6,0 F 30,0 101,0 110,0 02165-4-7320 8,0 F 30-35 102,0 111,0 90026-4-7320 14,0 F 40,0 130,0 139,0 subject to alterations max. 9 mm - Pull-off protector: The housing expands by max. 9 mm. The protector responds to overload by the generated excess pressure snapping off the internal lead in a predetermined breaking point. b c 10 7 1 - Material: Housing made of thermoplastic resin - Connection line: Multi-lead PVC cable 0.5 mm2 with brass lead tips - Approval: VDE according to DIN EN 60252 (VDE 0560/8) - Calculated life time: 400 V; -25 to +85C; 30,000 hrs; class A 450 V; -25 to +85C; 10,000 hrs; class B Oa M8 10 - Mounting: c is the overall dimension of the capacitor which has to be taken into account when mounting the part. The capacitor design, however, depends on the manufacturer. The expansion (9 mm) is either added to dimension b, or it is already integrated in the capacitor. MKP motor capacitors P0 (without fuse) Part no. 99832-4-7320 Capacity a b (max.) c 9,0 F 35,0 70,0 100,0 subject to alterations 161 Connection leads 230 V Jacketed cable, internal leads H03VV-F3G0,5 black Connector shell AMP 350 779-4 Brass lead tips 6 85 a 3 x female terminal AMP 926 884-1 Lead connections for AC centrifugal modules (230 V) Part no. a 23030-4-1012 450,0 23031-4-1012 1000,0 23032-4-1012 1300,0 23033-4-1012 1600,0 23034-4-1012 2300,0 subject to alterations 162 - Plug assignment: 1 = green/yellow 2 = blue 3 = brown 4 = not assigned Electrical connections EC H5) Technical features (M3G 055 Speed-controlled): * Output 10 VDC max. 1,1 mA * Tach output * Over-temperature protected motor * Motor current limitation * Locked-rotor protection * Soft start * Control interface with SELV potential safely disconnected from the mains Customer circuit max. speed Connection Speed setting Fan L 2 6 N 7 3,15AT 3 AC1 P AC2 N PE 1-10V 1 7 4 PE1 10V -> n = max 1V -> n = min <1V -> n = 0 +10V 6 Imax=1.1mA 10V/PWM 7 47k Speed setting with PWM 1-10kHz Speed setting with potentiometer 47k 1F GND 4 15V Tach 6 5 680R Imax=10mA 3 1 4 2 ZMM47 7 7 10K 12V 4 4 100% PWM -> n = max 10% PWM -> n = min <10% PWM -> n = 0 Line Connection Colour Assignment / function 2 L brown Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range 3 N blue Neutral conductor 1 PE green/yellow Protective earth 7 0-10V PWM yellow Control input 0 - 10 V or PWM, electrically isolated 5 Tach white Tach output: Open Collector, 1 pulse per revolution, electrically isolated, Isink max=10mA 6 10V/max.1.1mA red Voltage output 10 V / 1.1 mA, electrically isolated 4 GND blue GND - Connection for control interface 163 Electrical connections EC H3) Technical features (M3G 045 / M3G 055 with 2 Speed stages): * Speed adjustment input (230V) * Over-temperature protected electronics / motor * Motor current limitation * Locked-rotor protection * Soft start Customer circuit Connection Fan L AC1 P N AC2 N CON10 CON11 SL CON70 PE CON10 CON11 CON70 CON70 CON12 Line Connection Colour Assignment / function CON10 L black Power supply 230 VAC, 50 - 60 Hz CON11 N blue Neutral conductor CON12 PE green/yellow Protective earth CON70 SL brown Speed selection: switch open = speed 1; switch closed = speed 2 164 PE1 Electrical connections EC H4) Technical features (M3G 045 / M3G 055 Speed-controlled; M3G 074): * Control input 0-10 VDC / PWM * Output 10 VDC max. 1,1 mA * Tach output * Over-temperature protected electronics / motor * Motor current limitation * Locked-rotor protection * Soft start Customer circuit max. speed Connection Speed setting Fan L AC1 P N AC2 N CON10 3 2 CON11 PE 1-10V CON12 2 1 PE1 10V -> n = max 1V -> n = min <1V -> n = 0 +10V 1 3 2 4 3 Imax=1.1mA 10V/PWM 2 47k Speed setting with PWM 1-10kHz Speed setting with potentiometer 47k 1F GND 1 15V Tach 3 4 680R Imax=10mA 3 1 4 2 ZMM47 2 2 10K 12V 1 1 100% PWM -> n = max 10% PWM -> n = min <10% PWM -> n = 0 Line Connection Colour Assignment / function CON10 L black Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range CON11 N blue Neutral conductor CON12 PE green/yellow Protective earth 1 GND blue GND - Connection for control interface 2 0-10V PWM yellow Control input 0 - 10 V or PWM, electrically isolated 3 10V/max.1.1mA red Voltage output 10 V / 1.1 mA, electrically isolated, not short-circuit-proof 4 Tach white Tach output: Open Collector, 1 pulse per revolution, electrically isolated 165 Electrical connections EC P5) Technical features: * PFC (aktive) * integrated PID controller * Control input 0-10 VDC / PWM * Output 10 VDC max. 10 mA * Operation and alarm display * RS485 MODBUS RTU * * * * * Full Speed Motor current limitation, Alarm relay Line undervoltage / phase failure detection Over-temperature protected electronics / motor Locked-rotor protection, Soft start Control interface with SELV potential safely disconnected from the mains Speed setting PE 1 8 8 PE 2 PE1 1-10 V N 12 3 10 V -> n = max 1 V -> n = min <1 V -> n = 0 L A2 A1 NC 6 14 5 11 13 COM 7 0-10 V 0-10 V 8 Speed setting with potentiometer 47 K RSB 470 nF 47 K RSB 10 RSA 13 RSA 11 GND 10 K 12 8 0V 10 V 10 V 13 10 Imax=10 mA 12 Customer circuit Connection Fan N L NC COM 0-10 V RSB RSA GND +10 V Line 2 PE Line 1 green/yellow blue black white 1 white 2 yellow brown white blue red Line No. Connection Colour Assignment / function 1 1, 2 PE green/yellow Protective earth 1 3 N blue Supply voltage, neutral conductor, see type plate for voltage range, 50/60 Hz 1 1 5 6 L NC black white 1 Supply voltage, phase, see type plate for voltage range, 50/60 Hz 1 7 COM white 2 Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1) min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side 2 8 0-10 V yellow Analogue input (set value), SELV 0-10 V, Impedance 100 k, parametrisable curve 2 10 RSB brown RS485 interface for MODBUS, RSB, SELV 2 11 RSA white RS485 interface for MODBUS, RSA, SELV 2 2 12 13 GND +10 V blue red Reference ground for control interface, SELV 166 Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1) min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof, Power supply for external devices (e.g. potentiometer) Electrical connections EC P6) Technical features: * PFC (passive) * integrated PID controller * Control input 0-10 VDC / PWM * Output 10 VDC max. 10 mA * Operation and alarm display * RS485 MODBUS RTU Full Speed * * * * * Motor current limitation, Alarm relay Line undervoltage / phase failure detection Over-temperature protected electronics / motor Locked-rotor protection, Soft start Control interface with SELV potential safely disconnected from the mains Speed setting PE 1 8 8 PE 2 13 PE1 L1 1-10 V 3 12 L2 10 V -> n = max 1 V -> n = min <1 V -> n = 0 4 L3 14 A2 A1 NC 6 11 5 COM 7 0-10 V Speed setting with potentiometer 0-10 V 8 47 K RSB RSB 10 13 470 nF RSA 11 GND 8 10 K 47 K RSA 12 0V 10 V 10 V 13 12 10 Imax=10 mA Customer circuit Connection Fan L1 L2 L3 NC COM 0-10 V RSB RSA GND +10 V Line 2 PE Line 1 green/yellow black black black white 1 white 2 yellow brown white blue red Line No. Connection Colour Assignment / function 1 1, 2 PE green/yellow Protective earth 1 1 3, 4, 5 6 L1, L2, L3 NC black white 1 Supply voltage, see type plate for voltage range, 50/60 Hz 1 7 COM white 2 Status relay, floating status contact, common connection, contact rating 250 VAC / 2 A (AC1) min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side 2 8 0-10 V yellow Analogue input (set value), SELV 0-10 V, Impedance 100 k, parametrisable curve 2 10 RSB brown RS485 interface for MODBUS, RSB, SELV 2 11 RSA white RS485 interface for MODBUS, RSA, SELV 2 2 12 13 GND +10 V blue red Reference ground for control interface, SELV Status relay, floating status contact, break for failure, contact rating 250 VAC / 2 A (AC1) min. 10 mA, basic insulation on mains side and reinforced insulation on control interface side Fixed voltage output 10 VDC, SELV +10 V +/- 3%), max. 10 mA, short-circuit-proof, Power supply for external devices (e.g. potentiometer) 167 Electrical connections EC M4) Tach output * Control interface with SELV potential RS485 MODBUS-RTU safely disconnected from the mains Alarm relay Line undervoltage / phase failure detection Motor current limitation Output limit Over-temperature protected electronics / motor Reverse polarity and locked-rotor protection Soft start +20 V Ain2 I Aout +10 V Ain1 I Din1 N Ain2 U Ain1 U L1 GND GND KL1 PE Din3 RS B NO Din2 KL2 RS A KL3 NC * * * * * * * * * COM Technical features: * PFC (aktive) * integrated PID controller * Control input 0-10 VDC / PWM * Input for sensor 0-10 V bzw. 4-20 mA * External 24 V input (programming) * External release input * Output for slave 0-10 V max. 3 mA * Output 20 VDC (20 %) max. 50 mA * Output 10 VDC (+10 %) max. 10 mA Connector Connection Assignment / function KL1 N Mains supply connection, supply voltage 1~200-277 VAC, 50/60 Hz L1 Mains supply connection, supply voltage 1~200-277 VAC, 50/60 Hz PE NC Earth connection, PE connection Status relay, floating status contact, option 1: break with error, option 2: break with error for run monitor error message COM Status relay, floating status contact, changeover contact, common connection, contact rating 250 VAC / 2 A (AC1) NO Status relay, floating status contact, option 1: close with error, option 2: close with run monitor error message PE KL2 KL3 Din1 Digital input 1: enabling of electronics; enabling: open pin or applied voltage 5 to 50 VDC; disabling: bridge to GND or applied voltage < 0,8 VDC; reset function: triggers software reset after a level change to < 0,8 V Ain1 I Analogue input 1 (set value); 4-20 mA; Ri= 100 ; parametrisable curve; only usable as alternative to input Ain1 U +10 V Fixed voltage output 10 VDC; +10 V 3 %; max. 10 mA; short circuit proof; power supply for ext. devices (e.g. potentiometer) Ain1U Analogue input 1 (set value); 0-10 V; Ri= 100 k; parametrisable curves; only usable as alternative to input Ain1 I GND Signal ground for control interface RSB Bus connection RS485; RSB; MODBUS RTU RSA Aout Bus connection RS485; RSA; MODBUS RTU Analogue output 0-10 V; max. 5 mA; output of the actual motor control factor (output voltage of electronics)/of the actual motor speed; parametrisable curve Ain2 I Analogue input 2; actual sensor value 4-20 mA; Ri= 100 ; parametrisable curve; only useable as alternative to input Ain2 U +20 V Fixed voltage output 20 VDC; +20 V +25/-10 %; max. 50 mA; short circuit proof; power supply for ext. devices (e.g. sensors) Ain2 U Analogue input 2; actual sensor value 0-10 V; Ri= 100 k; parametrisable curve; only useable as alternative to input Ain2 I GND Din3 Signal ground for control interface Digital input 3: Control characteristic of the integrated controller; according to EEPROM setting, the control characteristic of the integrated controller is normally/inversely selectable per BUS or per digital input; normal: open pin or applied voltage 5 to 50 VDC; inverse: bridge to GND or applied voltage < 0,8 VDC Din2 Digital input 2: parameter set switch 1/2; according to EEPROM setting, thr valid/used parameter set is selectable per BUS or per digital input Din2. Parameter set 1: open pin or applied voltage 5 to 50 VDC; parameter set 2: bridge to GND or applied voltage < 0,8 VDC 168 Electrical connections EC M5) Technical features: * PFC (passive) * integrated PID controller * Control input 0-10 VDC / PWM * External release input * External 24 V input (programming) * Output 10 VDC max. 10 mA * Operation and alarm display * RS485 MODBUS-RTU * * * * * * * Motor current limitation Alarm relay Line undervoltage / phase failure detection Over-temperature protected electronics / motor Reverse polarity and locked-rotor protection Soft start Control interface with SELV potential safely disconnected from the mains KL2 KL1 4 L3 3 L2 NC C 2 L1 Ain1 U GND 1 PE +10 V 8 RS B 7 Din1 6 RS A 5 1 2 3 Connector Pin Connection Assignment / function KL1 1 L1 Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz 2 L2 Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz 3 L3 Mains supply connection, supply voltage 3~380-480 VAC; 50/60 Hz PE Earth connection, PE connection 1 RSA Bus connection RS485; RSA; MODBUS RTU 2 RSB Bus connection RS485; RSB; MODBUS RTU 3 GND Signal ground for control interface 4 5 C Din1 Status relay, floating status contact, changeover contact, common connection 250 VAC / 2 A (AC1) PE KL2 Digital input 1: enabling of electronics; enabling: open pin or applied voltage 5 to 50 VDC; disabling: bridge to GND or applied voltage < 1 VDC; reset function: triggers software reset after a level change to < 1V 6 +10 V Fixed voltage output 10 VDC; +10 V 3 %; max. 10 mA; short circuit proof; power supply for ext. devices (e.g. potentiometer) 7 Ain1 U Analogue input 1 (set value); 0-10 V; Ri= 100 k; parametrisable curves 8 NC Status relay, floating status contact, break with error 169 Electrical connections AC A1) / A2a) A1) Single-phase capacitor motor (1~ 230 VAC power line) with TOP wired internally N PE L C U2 Z U1 U1 = blue U2 = black Z = brown = green/yellow TOP A2a) Single-phase capacitor motor (1~ 230 VAC power line) with connection for external TOP PE L U1 170 N C U2 Z TOP U1 = blue U2 = black Z = brown = green/yellow Electrical connections AC D2) / F1a) D2) Star connection (3~ 400 VAC power line) with TOP L1 PE L2 U1 V1 W1 U2 V2 W2 L3 TOP U1 U2 V1 V2 W1 W2 = = = = = = = black green blue white brown yellow green/yellow Direction of rotation is reversed by swapping two line phases. F1a) Delta connection (3~ 400 VAC power line) with TOP L1 PE L2 U1 V1 U2 V2 L3 W1 W2 TOP U1 U2 V1 V2 W1 W2 = = = = = = = blue green blue white brown yellow green/yellow Direction of rotation is reversed by swapping two line phases 171 Technical parameters & scope High standards for all ebm-papst products Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best possible product for your application. Careful monitoring of the market ensures that technical innovations are reflected in the improvements of our products. Based on the technical parameters listed below and the ambience you want our product to operate in, we here at ebm-papst can always work out the best solution for your specific application.. General performance parameters The majority of our products use maintenance-free ball bearings for Any deviations from the technical data and parameters described here any mounting position possible. As an option, sleeve bearings can be are listed on the product-specific data sheet. used, which is indicated on the product-specific data sheet wherever Type of protection The type of protection is specified in the product-specific data sheets. applicable. The service life L10 of the ball bearings can be taken as approx. 40,000 operating hours at an ambient temperature of 40 C, yet this estimate Insulation class can vary according to the actual ambient conditions. The insulation class is specified in the product-specific data sheets. We will gladly provide you with a lifetime calculation taking into account your specific operating conditions. Mounting position The mounting position is specified in the product-specific data sheets. Motor protection / thermal protection Information on motor protection and thermal protection is provided in the Condensate discharge holes product-specific data sheets. Information on the condensate discharge holes is provided in the Depending on motor type and field of application, the following protective product-specific data sheets. features are realised: Mode of operation - Thermal overload protection (TOP), either in-circuit or external The mode of operation is specified in the product-specific data sheets. - PTC with electronic diagnostics Protection class - Thermal overload protection (TOP) with electronic diagnostics - Impedance protection The protection class is specified in the product-specific data sheets. Service life The service life of ebm-papst products depends on two major factors: - The service life of the insulation system - The service life of the bearing system - Current limitation via electronics If an external TOP is connected, the customer has to make sure to connect a conventional trigger device for switching it off. Products without fitted TOP and without protection against improper use, a motor protection complying with the valid standards has to be installed. The service life of the insulation system mainly depends on voltage level, Mechanical strain / performance parameters temperature and ambient conditions, such as humidity and condensation. All ebm-papst products are subjected to comprehensive tests complying The service life of the bearing system depends mainly on the thermal load with the normative specifications. In addition to this, the tests also reflect on the bearing. the vast experience and expertise of ebm-papst. 172 Vibration test Standards Vibration tests are carried out in compliance with Information on standards is provided in the product-specific data sheets. - Vibration test in operation according to DIN IEC 68, parts 2-6 - Vibration test at standstill according to DIN IEC 68, parts 2-6 EMC Information on EMC standards is provided in the product-specific data Shock load sheets. Shock load tests are carried out in compliance with Complying with the EMC standards has to be established on the final - Shock load according to DIN IEC 68, parts 2-27 appliance, as different mounting situations can result in changed EMC Balancing quality properties. Testing the balancing quality is carried out in compliance with Leakage current - Residual imbalance according to DIN ISO 1940 Information on the leakage current is provided in the product-specific - Standard balancing quality level G 6.3 data sheets. Should you require a higher balancing quality level for your specific Measuring is according to IEC 60990. application, please let us know and specify this when ordering your product. Approvals In case you require a specific approval for your ebm-papst product Chemo-physical strain / performance parameters (VDE, UL, GOST, CCC, CSA, etc.) please let us know. Should you have questions about chemo-physical strain, please direct Most of our products can be supplied with the relevant approval. them to your ebm-papst contact. Information on existing approvals is provided in the product-specific Fields of application, industries and applications data sheets. Our products are used in various industries and applications: Air performance measurements Ventilation, air-conditioning and refrigeration technology, clean room All air performance measurements are carried out on suction side and on technology, automotive and rail technology, medical and laboratory tech- chamber test beds conforming to the specifications as per ISO 5801 and nology, electronics, computer and office technology, telecommunications, DIN 24163. The fans under test are installed in the measuring chamber at household appliances, heating, machines and plants, drive engineering. free air intake and exhaust (installation category A) and are operated at Our products are not designed for use in the aviation and aerospace nominal voltage, with AC also at nominal frequency, and without any industry! additional components such as guard grilles. Legal and normative directives The products described in this catalogue are designed, developed and As required by the standard, the air performance curves correspond to an air density of 1.2 kg/m3. produced in keeping with the standards in place for the relevant product and, if known, the conditions governing the relevant fields of application. 173 Technical parameters & scope Measurement conditions for air and noise measurement Sound pressure level and sound level ebm-papst products are measured under the following conditions: All acoustic values are established according to ISO 13347, DIN 45635 - Axial and diagonal fans in direction of rotation "V" in full nozzle and and ISO 3744/3745 to accuracy class 2 and given in A-rated form. without guard grille When the sound pressure level (Lp) is measured, the microphone is on - Backward curved centrifugal fans, free-running and with inlet nozzle the intake side of the fan being tested, usually at a distance of 1 m on - Forward curved single and dual inlet centrifugal fans with housing the fan axis. Noise measurements All noise measurements are carried out in low-reflective test rooms with reverberant floor. Thus the ebm-papst acoustic test chambers meet the requirements of precision class 1 according to DIN EN ISO 3745. For noise measurement, the fans being tested are placed in a reverberant wall and operated at nominal voltage (for AC, also at nominal frequency) without additional attachments such as the guard grille. To measure the sound power level (Lw), 10 microphones are distributed over an enveloping surface on the intake side of the fan being tested (see graphic). The sound power level measured can be roughly calculated from the sound pressure level by adding 7 dB. Measuring configuration as per ISO 13347-3 respectively DIN 45635-38: 10 measuring points dD h = 1,5d ... 4,5d D 1,5d Measurement area S = 6d2 + 7d (h + 1,5d) h 3d 2d 174 9 dB. Thus the overall sound level of the installation can be expected to be 84 dB(A). 15 10 9 Example: 8 A3G800 axial fans are on a condenser. According to the data sheet, the sound pressure level of a fan is approximately 75 dB(A). The level increase measured from the diagram is 5 the noise values specified in the data sheet. This is shown in the diagram opposite. 0 The noise characteristics of multiple identical fans can be determined in advance based on [dB] [dB(A)] Adding 2 noise sources with the same level results in a level increase of approx. 3 dB. Increase in sound pressure / sound power level Combined level of multiple same-level sound sources 1 2 3 4 5 6 7 8 9 10 15 20 25 point and an axial fan A3G710 with 71 dB(A) in a ventilation unit. The level difference is 4 dB. The level increase can now be read in the diagram as approx. 1.5 dB. This means that the overall sound level of the unit can be expected to be 76.5 dB(A). 3 2 1,5 Example: There is an axial fan A3G800 with a sound pressure level of 75 dB(A) at the operating 1 levels given in the data sheet. This is shown in the diagram opposite. 0 The acoustic performance of two different fans can be predetermined based on the sound Increase in sound pressure / sound power level Combined level of two different-level sound sources [dB] [dB(A)] Number of sources of sound with identical level 0 4 8 12 16 20 Sound power level is independent of distance to the sound source. In contrast to this, sound -10 pressure level decreases the further away the noise source is. The adjacent diagram shows the 0 [dB] [dB(A)] Distance laws 24 [dB] [dB(A)] Difference in level with two sources of sound decrease in level under far sound field conditions. Far sound field conditions apply whenever the ably smaller. The following example only applies to far sound field conditions and can vary strongly depending on the installation effects: With an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of 1 m. According to the adjacent diagram, at a distance of 20 m we would get a reduction by -20 -26 -30 In the near field of the fan, other correlations apply and the decrease in levels can be consider- -40 this complex topic. Per doubling of distance, the level in the far sound field decreases by 6 dB. Decrease in sound pressure level distance between microphone and fan is big when compared to fan diameter and wavelength to be considered. For more information on far sound field, please consult the relevant literature on 1 Distance 2 5 10 20 50 100 [m] 26 dB, i.e. a sound pressure level of 39 dB(A). 175 ebm-papst in Germany ebm-papst Mulfingen GmbH & Co. KG Bachmuhle 2 74673 Mulfingen GERMANY Phone +49 7938 81-0 Fax +49 7938 81-110 info1@de.ebmpapst.com 176 ebm-papst St. Georgen GmbH & Co. KG Hermann-Papst-Strae 1 78112 St. Georgen GERMANY Phone +49 7724 81-0 Fax +49 7724 81-1309 info2@de.ebmpapst.com Berlin Dipl.-Ing. (TH) Jens Duchow Handelstrae 7 16341 Panketal GERMANY Phone +49 30 944149-62 Fax +49 30 944149-63 Jens.Duchow@de.ebmpapst.com Heilbronn / Heidelberg Dipl.-Ing. Mark Gartner Gehrweg 12 74199 Unterheinriet GERMANY Phone +49 7130 404569-1 Fax +49 7130 404569-2 Mark.Gartner@de.ebmpapst.com Bielefeld Dipl.-Ing. (FH) Wolf-Jurgen Weber Niehausweg 13 33739 Bielefeld GERMANY Phone +49 5206 91732-31 Fax +49 5206 91732-35 Wolf-Juergen.Weber@de.ebmpapst.com Kassel Dipl.-Ing. (FH) Ralph Bruck Hoherainstrae 3 b 35075 Gladenbach GERMANY Phone +49 6462 4071-10 Fax +49 6462 4071-11 Ralph.Brueck@de.ebmpapst.com Dortmund Dipl.-Ing. (FH) Hans-Joachim Pundt Auf den Steinern 3 59519 Mohnesee-Vollinghausen GERMANY Phone +49 2925 800-407 Fax +49 2925 800-408 Hans-Joachim.Pundt@de.ebmpapst.com Koblenz Winfried Schaefer Hinter der Kirch 10 56767 Uersfeld GERMANY Phone +49 2657 16-96 Fax +49 2657 16-76 Winfried.Schaefer@de.ebmpapst.com Frankfurt Dipl.-Ing. Christian Kleffmann Dr.-Hermann-Krause-Strae 23 63452 Hanau GERMANY Phone +49 6181 1898-12 Fax +49 6181 1898-13 Christian.Kleffmann@de.ebmpapst.com Munich Dipl.-Wirt.-Ing. (FH) Jens Peter Landsbergerstrae 14 86932 Purgen GERMANY Phone +49 8196 99877-54 Fax +49 8196 99877-55 Jens.Peter@de.ebmpapst.com Halle Dipl.-Ing. (TU) Michael Hanning Lercheneck 4 06198 Salzatal / OT Lieskau GERMANY Phone +49 345 55124-56 Fax +49 345 55124-57 Michael.Hanning@de.ebmpapst.com Nuremberg Dipl.-Wirt.-Ing. (FH) Axel Resch Dr.-August-Koch-Str. 1 91639 Wolframs-Eschenbach GERMANY Phone +49 9875 9783-170 Fax +49 9875 9783-171 Axel.Resch@de.ebmpapst.com Hamburg Ingenieurburo Breuell GmbH Ing. Dirk Kahl Elektroingenieur Grutzmuhlenweg 48 22339 Hamburg GERMANY Phone +49 40 538092-19 Fax +49 40 538092-84 Dirk.Kahl@de.ebmpapst.com Offenburg Dipl.-Ing. (FH) Ralf Braun Hubeneck 21 77704 Oberkirch GERMANY Phone +49 7802 9822-52 Fax +49 7802 9822-53 Ralf.Braun@de.ebmpapst.com fan agent Stuttgart Dipl.-Ing. (FH) Rudi Weinmann Hindenburgstrae 100/1 73207 Plochingen GERMANY Phone +49 7153 9289-80 Fax +49 7153 9289-81 Rudi.Weinmann@de.ebmpapst.com compact fan agent motor specialist ebm-papst Landshut GmbH Hofmark-Aich-Strae 25 84030 Landshut GERMANY Phone +49 871 707-0 Fax +49 871 707-465 info3@de.ebmpapst.com Ulm M.Sc. Reinhard Sommerreier Am Silbermannpark 10 86161 Augsburg GERMANY Phone +49 821 6610-7023 Fax +49 821 6610-7024 Reinhard.Sommerreisser@de.ebmpapst.com Distributoren Frankfurt R.E.D. Handelsgesellschaft mbH Gutenbergstrae 3 63110 Rodgau - Jugesheim GERMANY Phone +49 6106 841-0 Fax +49 6106 841-111 info@red-elektromechanik.de www.red-elektromechanik.de Hamburg Breuell + Hilgenfeldt GmbH Grutzmuhlenweg 48 22339 Hamburg GERMANY Phone +49 40 538092-20 Fax +49 40 538092-84 info@breuell-hilgenfeldt.de Munich A. Schweiger GmbH Ohmstrae 1 82054 Sauerlach GERMANY Phone +49 8104 897-0 Fax +49 8104 897-90 info@schweiger-gmbh.de www.schweiger-gmbh.com (1 to 5 pieces) North Breuell + Hilgenfeldt GmbH Grutzmuhlenweg 48 22339 Hamburg GERMANY Phone +49 40 538092-20 Fax +49 40 538092-84 ebmpapst@breuell-hilgenfeldt.de South HDS Ventilatoren Vertriebs GmbH Glaswiesenstrae 1 74677 Dorzbach GERMANY Phone +49 7937 80355-20 Fax +49 7937 80355-25 info@hds-gmbh.net www.hds-gmbh.net motor agent ebm-papst in Europe Europe Austria ebm-papst Motoren & Ventilatoren GmbH Straubingstrae 17 4030 Linz AUSTRIA Phone +43 732 321150-0 Fax +43 732 321150-20 info@at.ebmpapst.com www.ebmpapst.at Belarus ebm-papst Bel AgmbH P.O. Box 117 220138 Minsk BELARUS Phone +375 17 3851556 Fax +375 17 3851556 info@by.ebmpapst.com www.ebmpapst.by Belgium ebm-papst Benelux B.V. Sales office Belgium-Luxemburg Romeinsestraat 6/0101 Research Park Haasrode 3001 Heverlee-Leuven BELGIUM Phone +32 16 396-200 Fax +32 16 396-220 info@be.ebmpapst.com www.ebmpapst.be Bulgaria ebm-papst Romania S.R.L. Str. Tarnavei No. 20 500327 Brasov ROMANIA Phone +40 268 331859 Fax +40 268 312805 dudasludovic@xnet.ro Croatia ebm-papst Industries Kft. Ezred u. 2. 1044 Budapest HUNGARY Phone +36 1 8722-190 Fax +36 1 8722-194 office@hu.ebmpapst.com Czech Republic / Slovakia ebm-papst CZ s.r.o. Katanova 34a 620 00 Brno CZECH REPUBLIC Phone +420 544 502-411 Fax +420 547 232-622 info@ebmpapst.cz www.ebmpapst.cz Denmark ebm-papst Denmark ApS Vallensbaekvej 21 2605 Brondby DENMARK Phone +45 43 631111 Fax +45 43 630505 mail@dk.ebmpapst.com www.ebmpapst.dk Estonia ebm-papst Oy, Eesti Filiaal Kesk tee 13 Aaviku kula, Juri Tehnopark 75301 Rae Vald, Harjumaa ESTONIA Phone +372 65569-78 Fax +372 65569-79 www.ebmpapst.ee Finland ebm-papst Oy Puistotie 1 02760 Espoo FINLAND Phone +358 9 887022-0 Fax +358 9 887022-13 mailbox@ebmpapst.fi www.ebmpapst.fi France ebm-papst sarl ZI Nord - rue A. Mohler BP 62 67212 Obernai Cedex FRANCE Phone +33 820 326266 Fax +33 3 88673883 info@ebmpapst.fr www.ebmpapst.fr Greece Helcoma Th. Rotas & Co OE Davaki 65 17672 Kallithea-Attiki GREECE Phone +30 210 9513-705 Fax +30 210 9513-490 contact@helcoma.gr www.helcoma.gr Hungary ebm-papst Industries Kft. Ezred u. 2. 1044 Budapest HUNGARY Phone +36 1 8722-190 Fax +36 1 8722-194 office@hu.ebmpapst.com Iceland RJ Engineers Stangarhyl 1a 110 Reykjavik ICELAND Phone +354 567 8030 Fax +354 567 8015 rj@rj.is www.rj.is Ireland ebm-papst UK Ltd. Chelmsford Business Park Chelmsford Essex CM2 5EZ UNITED KINGDOM Phone +44 1245 468555 Fax +44 1245 466336 sales@uk.ebmpapst.com www.ebmpapst.co.uk AuBren Limited Portlaoise Business & Technology Park Mountrath Road Portlaoise, Co. Laois IRELAND Phone +353 57 8664343 Fax +353 57 8664346 sales@ie.aubren.com www.aubren.com Italy ebm-papst Srl Via Cornaggia 108 22076 Mozzate (Co) ITALY Phone +39 0331 836201 Fax +39 0331 821510 info@it.ebmpapst.com www.ebmpapst.it Macedonia ebm-papst Industries Kft. Ezred u. 2. 1044 Budapest HUNGARY Phone +36 1 8722-190 Fax +36 1 8722-194 office@hu.ebmpapst.com 177 ebm-papst in Europe Netherlands ebm-papst Benelux B.V. Engelseweg 127 5705 AC Helmond NETHERLANDS Phone +31 492 502-900 Fax +31 492 502-950 verkoop@nl.ebmpapst.com www.ebmpapst.nl Russia ebm-papst Ural GmbH Posadskaja-Strasse, 23(E), 3 620102 Ekaterinburg RUSSIA Phone +7 343 2338000 Fax +7 343 2337788 Konstantin.Molokov@ru.ebmpapst.com www.ebmpapst.ur.ru Switzerland ebm-papst AG Rutisbergstrasse 1 8156 Oberhasli SWITZERLAND Phone +41 44 73220-70 Fax +41 44 73220-77 verkauf@ebmpapst.ch www.ebmpapst.ch Norway ebm-papst AS P.B. 173 Holmlia 1203 Oslo NORWAY Phone +47 22 763340 Fax +47 22 619173 mailbox@ebmpapst.no www.ebmpapst.no ebm-papst Rus GmbH proezd 4529, vladenie 5, stroenie 1 141000 Mytistschi, Oblast Moskau RUSSIA Phone +7 495 9807524 Fax +7 495 5140924 info@ebmpapst.ru www.ebmpapst.ru Turkey Akantel Elektronik San. Tic. LTD. Sti. Ataturk Organize Sanayi Bolgesi 10007 SK. No.:6 35620 Cigli-Izmir TURKEY Phone +90 232 3282090 Fax +90 232 3280270 akantel@akantel.com.tr www.ebmpapst.com.tr Poland ebm-papst Polska Sp. z o.o. ul. Annopol 4A 03236 Warszawa POLAND Phone +48 22 6757819 Fax +48 22 6769587 office@ebmpapst.pl www.ebmpapst.pl Portugal ebm-papst (Portugal), Lda. Centro Empresarial de Alverca Rua de Adarse, Vale D'Ervas Corpo D / Fraccao 3 2615-178 Alverca do Ribatejo PORTUGAL Phone +351 218 394 880 Fax +351 218 394 759 info@pt.ebmpapst.com www.ebmpapst.pt Romania ebm-papst Romania S.R.L. Str. Tarnavei Nr. 20 500327 Brasov ROMANIA Phone +40 268 331859 Fax +40 268 312805 dudasludovic@xnet.ro 178 fan agent Serbia & Montenegro ebm-papst Industries Kft. Ezred u. 2. 1044 Budapest HUNGARY Phone +36 1 8722-190 Fax +36 1 8722-194 office@hu.ebmpapst.com Spain ebm-papst Iberica S.L. Avda. del Sistema Solar, 29 28830 San Fernando de Henares (Madrid) SPAIN Phone +34 91 6780894 Fax +34 91 6781530 ventas@ebmpapst.es www.ebmpapst.es Sweden ebm-papst AB Aggelundavagen 2 17562 Jarfalla SWEDEN Phone +46 10 4544400 Fax +46 8 362306 info@ebmpapst.se www.ebmpapst.se compact fan agent Ukraine ebm-papst Ukraine LLC Lepse Boulevard, 4, Building 21 03067 Kiev UKRAINE Phone +38 044 2063091 Fax +38 044 2063091 mail@ebmpapst.ua www.ebmpapst.ua United Kingdom ebm-papst UK Ltd. Chelmsford Business Park Chelmsford Essex CM2 5EZ UNITED KINGDOM Phone +44 1245 468555 Fax +44 1245 466336 sales@uk.ebmpapst.com www.ebmpapst.co.uk ebm-papst Automotive & Drives (UK) Ltd. The Smithy Fidlers Lane East Ilsley, Berkshire RG20 7LG UNITED KINGDOM Phone +44 1635 2811-11 Fax +44 1635 2811-61 A&Dsales@uk.ebmpapst.com www.ebmpapst-ad.com motor specialist motor agent ebm-papst in America and Africa America Argentina ebm-papst de Argentina S.A. Hernandarias 148 Lomas del Mirador Pcia. de Buenos Aires (1752) ARGENTINA Phone +54 11 46576135 Fax +54 11 46572092 ventas@ar.ebmpapst.com www.ebmpapst.com.ar Brasil ebm-papst Motores Ventiladores Ltda. Av. Jose Giorgi, 301 Galpoes B6+B7 Condominio Logical Center 06707-100 Cotia - Sao Paulo BRAZIL Phone +55 11 4613-8700 Fax +55 11 4777-1456 vendas@br.ebmpapst.com www.ebmpapst.com.br USA ebm-papst Inc. P.O. Box 4009 100 Hyde Road Farmington, CT 06034 UNITED STATES Phone +1 860 674-1515 Fax +1 860 674-8536 sales@us.ebmpapst.com www.ebmpapst.us ebm-papst Automotive & Drives, Inc. 3200 Greenfield, Suite 255 Dearborn, MI 48120 UNITED STATES Phone +1 313 406-8080 Fax +1 313 406-8081 automotive@us.ebmpapst.com www.ebmpapst-automotive.us Africa South Africa ebm-papst South Africa (Pty) Ltd. P.O. Box 3124 1119 Yacht Avenue 2040 Honeydew SOUTH AFRICA Phone +27 11 794-3434 Fax +27 11 794-5020 info@za.ebmpapst.com www.ebmpapst.co.za Canada ebm-papst Canada Inc. 1800 Ironstone Manor, Unit 2 Pickering, Ontario, L1W3J9 CANADA Phone +1 905 420-3533 Fax +1 905 420-3772 sales@ca.ebmpapst.com www.ebmpapst.ca Mexico ebm Industrial S. de R.L. de C.V. Paseo de Tamarindos 400-A-5to Piso Col. Bosques de las Lomas Mexico 05120, D.F. MEXICO Phone +52 55 3300-5144 Fax +52 55 3300-5243 sales@mx.ebmpapst.com www.ebmpapst.com.mx 179 ebm-papst in Asia and Australia Asia China ebm-papst Ventilator (Shanghai) Co., Ltd. No. 418, Huajing Road WaiGaoQiao Free Trade Zone No. 2001, Yang Gao (N) Road 200131 Shanghai P.R. of CHINA Phone +86 21 5046-0183 Fax +86 21 5046-1119 sales@cn.ebmpapst.com www.ebmpapst.com.cn Hong Kong ebm-papst Hong Kong Ltd. Room 17E, MG Tower 133 Hoi Bun Road, Kwun Tong Hong Kong P.R. of CHINA Phone +852 2145-8678 Fax +852 2145-7678 info@hk.ebmpapst.com Thailand ebm-papst Thailand Co., Ltd. 99/9 Moo 2, Central Chaengwattana Tower 14th Floor, Room 1402 Chaengwattana Road Bangtarad, Pakkret 11120 Nonthaburi THAILAND Phone +66 2 8353785-7 Fax +66 2 8353788 salesdept@th.ebmpapst.com Korea ebm-papst Korea Co. Ltd. 6F, Trutec Bldg. B 6-2, Digital Media City (DMC) Sangam-Dong, Mapo-Gu Seoul 121-270 KOREA Phone +82 2 366213-24 Fax +82 2 366213-26 info@kr.ebmpapst.com www.ebmpapst.co.kr United Arab Emirates ebm-papst Middle East FZE PO Box 17755 Jebel Ali Free Zone / FZS1 / AP05 Dubai UNITED ARAB EMIRATES Phone +971 4 88608-26 Fax +971 4 88608-27 info@ae.ebmpapst.com www.ebmpapst.ae India ebm-papst India Pvt. Ltd. 26/3, G.N.T. Road, Erukkencherry Chennai-600118 INDIA Phone +91 44 25372556 Fax +91 44 25371149 sales@in.ebmpapst.com www.ebmpapst.in Malaysia ebm-papst Malaysia Representative Office Unit 12-2, Jalan USJ Sentral 3 Persiaran Subang, Selangor Darul Ehsan 47600 Subang Jaya MALAYSIA Phone +60 3 8024-1680 Fax +60 3 8024-8718 salesdept@my.ebmpapst.com Indonesia ebm-papst Indonesia Representative Office German Centre, 4th Floor, Suite 4470 Jl. Kapt. Subijono Dj. Bumi Serpong Damai 15321 Tangerang INDONESIA Phone +62 21 5376250 Fax +62 21 5388305 salesdept@id.ebmpapst.com Singapore ebm-papst SEA Pte. Ltd. No. 23 Ubi Road 4 #06-00 Olympia Industrial Building Singapore 408620 SINGAPORE Phone +65 65513789 Fax +65 68428439 salesdept@sg.ebmpapst.com Israel Polak Bros. Import Agencies Ltd. 9 Hamefalsim Street Kiryat Arie, Petach-Tikva 49514 ISRAEL Phone +972 3 9100300 Fax +972 3 5796679 polak@polak.co.il www.polak.co.il 180 Japan ebm-papst Industries Japan K.K. 12th Floor, Benex S-3 Bldg. 3-20-8 Shinyokohama, Kohoku-ku 222-0033 Yokohama JAPAN Phone +81 45 47057-51 Fax +81 45 47057-52 info@jp.ebmpapst.com www.ebmpapst.jp fan agent Taiwan ETECO Engineering & Trading Corp. 10F-I, No. 92, Teh-Wei Str. Tsow-Inn District, Kaohsiung TAIWAN Phone +886 7 557-4268 Fax +886 7 557-2788 eteco@ms22.hinet.net www.ebmpapst.com.tw compact fan agent motor specialist Vietnam ebm-papst Vietnam Representative Office Room #102, 25 Nguyen Van Thu Street District 1 Ho Chi Minh City VIETNAM Phone +84 8 39104099 Fax +84 8 39103970 linh.nguyen@vn.ebmpapst.com Australia Australia ebm-papst A&NZ Pty Ltd. 10 Oxford Road Laverton North, Victoria, 3026 AUSTRALIA Phone +61 3 9360-6400 Fax +61 3 9360-6464 sales@ebmpapst.com.au www.ebmpapst.com.au New Zealand ebm-papst A&NZ Pty Ltd. 102 Henderson Valley Road Henderson, Auckland 1230 NEW ZEALAND Phone +64 9 837-1884 Fax +64 9 837-1899 sales@ebmpapst.com.au www.ebmpapst.com.au motor agent 181 Notes 182 183 www.ebmpapst.com 37850-7-8811 * 2013-05 * KD-3' Printed in Germany ebm-papst Mulfingen GmbH & Co. KG Bachmuhle 2 74673 Mulfingen Germany Phone +49 7938 81-0 Fax +49 7938 81-110 info1@de.ebmpapst.com The engineer's choice