87046-65 RN - AVX - Product.Network

REVISIONS

LTR

DESCRIPTION

DATE

APPROVED

A Added suggested sources of supply. 11 May 88 D. Moore

B

Added suggested source of supply and made

corrections.

27 Feb 90 D. Moore

C

Deleted and added suggested sources of supply.

Editorial changes throughout.

8 Oct 92 D. Moore

D Modified manufacturer’s PINs, modified 3.2.6.

Editorial changes throughout.

18 Jan 94 D. Moore

E Changes in accordance with NOR 5910-R005-96 23 May 96 A. Ernst

F

Revised sources of supply, added alternate

marking method, made editorial changes, and

converted references to MIL-PRF-49467.

5 April 99 J. Crum

G

Moved solderability testing from group A to group

B. Updated suggested sources of supply.

10 April 00 Kendall A. Cottongim

H

Removed suggested source of supply. Added

note 4 to figure 1. Added capacitor tolerance

note to 3.2.8.

16 January 01 Kendall A. Cottongim

J Added suggested source of supply. Changed

Johanson Dielectrics CAGE code.

12 September 01 Kendall A. Cottongim

K Updated name and address of vendor C. 4 November 02 Kendall A. Cottongim

L

Added Johanson Dielectrics as a suggested

source of supply.

18 August 2004 Kendall A. Cottongim

M

Added CalRamic Technologies as a suggested

source of supply.

19 April 2007 Michael A. Radecki

N

Changed drawing type to Source Control with

approved sources. Added manufacturer

eligibility criteria, paragraph 3.14. Added new

paragraph 6.3. Added an approved source.

21 October 2010 Michael A. Radecki

Prepared in accordance with ASME Y14.100 Source control drawing

REV STATUS

REV N N N N N N N N N

OF PAGES

PAGES 1 2 3 4 5 6 7 8 9

PMIC N/A

PREPA RED BY

ROBERT E. GRILLOT

DEFENSE ELECTRONIC SUPPLY CENTER

DAYTON, OH 45444-5000

Original date of

drawing

CHECKED BY

EDWARD H. BACK

TITLE

CAPACITORS, CERAMIC, M ULTILAYER, HIGH

22 April 1987

APPROVED BY

DAVID E. MOORE

VOLTAGE, CG, 1,000 V DC

SIZE

A

CODE IDENT. NO.

14933

DWG NO.

87046

REV N

PAGE 1 OF 9

AMSC N/A 5910-E476

CURRENT DESIGN ACTIVITY CAGE CODE 037Z3

HAS CHANGED NAMES TO:

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHIO

SIZE

A

CODE IDENT NO.

14933

DWG NO.

87046

REV N PAGE 2

1. SCOPE

1.1 Scope. This drawing and MIL-PRF-49467 describe the requirements for high voltage multilayer ceramic capacitors.

1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows:

87046 -XX

| |

Drawing Dash number

number (see table I)

2. APPLICABLE DOCUMENTS

2.1 General. The documents lis ted in this section are specified in sections 3 and 4 of this specification. This section does not

include documents cited in other sections of this specification or recommended for additional information or as examples. While every

effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified

requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this

document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation

or contract.

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-PRF-49467 - Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose),

Established Reliability, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-202 - Test Methods Standard Electronics and Electrical Component Parts.

MIL-STD-1285 - Marking of Electrical and Electronic Parts.

(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or https://www.assist.daps.dla.mil/ or

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this

document and the references cited herein, the text of this document takes precedence. Nothing in this document, however,

supersedes applicable laws and regulations unless a specific exemption has been obtained.

3. REQUIREMENTS

3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49467 and herein

(see figure 1).

3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3

percent.

3.1.2 Case. Epoxy, conformally coated.

3.1.3 Operating temperature range. The operating temperature range shall be -55°C to +125°C.

3.2 Electrical characteristics.

3.2.1 Rated voltage. The rated voltage shall be 1,000 volts dc.

3.2.2 Dielectric type. CG.

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHIO

SIZE

A

CODE IDENT NO.

14933

DWG NO.

87046

REV N PAGE 3

NOTES:

1. Dimensions are in inches.

2. Metric equivalents are given for general information only.

3. H dimension includes meniscus.

4. S dimension shall be maintained from chip body to end of leads.

FIGURE 1. Case dimensions and c onfiguration.

Case Sizes (max.) Lead spacing

code

Width

(W)

Height

(H)

Thickness

(T) ± .030

(S)

A

B

C

D

E

F

G

.250

.320

.370

.470

.570

.670

.770

.220

.280

.300

.400

.500

.600

.720

.200

.250

.270

.170

.220

.275

.375

.475

.575

.675

Inches

mm

Inches

mm

.002

.025

.030

.170

.200

.220

.250

.270

.275

.280

.300

.320

.370

0.05

0.64

0.76

4.32

5.08

5.59

6.35

6.86

6.99

7.11

7.62

8.13

9.40

.375

.400

.470

.475

.500

.570

.575

.600

.670

.675

.720

.770

1.250

9.53

10.16

11.94

12.07

12.70

14.48

14.61

15.24

17.02

17.15

18.29

19.56

31.75

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHIO

SIZE

A

CODE IDENT NO.

14933

DWG NO.

87046

REV N PAGE 4

3.2.3 Temperature coefficient. 0 ppm/°C ±30 ppm/°C. (For MIL-PRF-49467 group B voltage temperature limits, use step a through

step d only.)

3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202. Capacitance values ≤ 100 pF: 1 MHz

at 1.0 V rms at +25°C. Capacitance values > 100 pF: 1 kHz at 1.0 V rms at +25°C.

3.2.5 Dissipation factor (+25°C). 0.1 percent maximum (measured under the same conditions as capacitanc e).

3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202 with charging current limited to 50 mA. Two

minutes maximum charging time. At +25°C, 500 V dc: 100,000 megohms or 1,000 megohms microfarad, whichever is less. At

+125°C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less.

3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage.

3.2.8 Capacitance tolerance. J = ±5 percent, K = ±10 percent. J tolerance parts may be substituted for K tolerance parts, with

acquiring activity approval.

3.3 Solderability of terminals. In accordance with MIL-PRF-49467.

3.4 Vibration. In accordance with MIL-PRF-49467.

3.5 Shock. In accordance with MIL-PRF-49467, with rated voltage and three blows in each of six directions.

3.6 Immersion cycling. In accordance with MIL-PRF-49467.

3.7 Moisture resistance. In accordance with MIL-PRF-49467 with 20 continuous cycles.

3.8 Life. One hundred percent of rated voltage applied at +125°C for 1,000 hours. Resistors with a high value such as 1 megohm

may be used in series with each part under test in lieu of fuses.

3.9 Thermal shock. Method 107 of MIL-STD-202, test condition B except low temperature is -55°C.

3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such as 1

megohm may be used in series with each part under test in lieu of fuses.

3.11 Terminal strength. In accordance with MIL-PRF-49467.

3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified

in 1.2, the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minim um . Case codes

A, B, and C (at the option of the manufacturer) may be marked as indicated below with full marking on the package.

Front Back

Last 3 digits of drawing number---- ------ Manufacturer’s trademark

Dash number -------------------------- ------ Date code

FIGURE 2. Alternate marking method for A, B, and C case codes.

3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials

should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance

requirements, and promotes economically advantageous life cycle costs.

3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the

MIL-PRF-49467 Qualified Products Database for at least one part, or provide data as requested by DLA Land and Maritime – VAT.

3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved

source of supply.

046

-49

XYZ

430

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHIO

SIZE

A

CODE IDENT NO.

14933

DWG NO.

87046

REV N PAGE 5

3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or

appearance.

TABLE I. Electrical characteristics

DSCC

drawing

87046-

Capacitance Capacitance

tolerance Case code DSCC

drawing

87046-

Capacitance Capacitance

tolerance Case code

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

10 pF

12 pF

15 pF

18 pF

22 pF

27 pF

33 pF

39 pF

47 pF

56 pF

68 pF

82 pF

100 pF

120 pF

150 pF

180 pF

220 pF

270 pF

330 pF

390 pF

470 pF

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

A

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

560 pF

680 pF

820 pF

1000 pF

1200 pF

1500 pF

1800 pF

2200 pF

2700 pF

3300 pF

3900 pF

4700 pF

5600 pF

6800 pF

8200pF

.010 µF

.012 µF

.015 µF

.018 µF

.022 µF

.025 µF

.025

µ

F

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

J

K

A

B

C

D

E

F

G

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHIO

SIZE

A

CODE IDENT NO.

14933

DWG NO.

87046

REV N PAGE 6

4. VERIFICATION

4.1 Qualification inspection. Qualification inspection is not required.

4.2 Conformance inspection.

4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B

inspections of MIL-PRF-49467, provided they are listed in this drawing. PPM testing and calculation is not applicable. Solderability

testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted.

4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu

of performing group B tests (see 6.2d).

5. PACKAGING

5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When

packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible

packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s

packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data

retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or

by contacting the responsible packaging activity.

6. NOTES

(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)

6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified

military devices that will perform the required function are not available for original equipment manufacturer application. This drawing

is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When

a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and

will not be used for new design.

6.2 Ordering data. The contract or purchase order should specify the following:

a. Complete PIN (see 1.2).

b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed

conformance inspection with each shipment of parts by the manufacturer.

c. Requirements for packaging and packing.

d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements.

e. Requirements for notification of change of product to procuring activity, if applicable.

6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth

problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical

operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not

prevent the formation of whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional

information on this matter, refer to ASTM B545 (Standard Specification for Electrodeposited Coating of Tin).

6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared

specification or drawing.

6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and

the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and

Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to capacitorfilter@dla.mil also by telephone

(614) 692-4709 or DSN 850-4709.

1/ DSCC

drawing

87046-

Vendor A

similar

vendor type

Vendor B

similar

vendor type

Vendor C and J

similar

vendor type

Vendor D

similar

vendor type

Vendor E

similar

vendor type

Vendor F

similar

vendor type

Vendor G

similar

vendor type

Vendor H

similar

vendor type

01

SV01AA100JHA

1515CN100JA102

102H42N100JQ3H

UTC4125-01

126974-01

PCI1552-01

1515N100J102LEXH

10HV01N100JM

02

SV01AA100KHA

1515CN100KA102

102H42N100KQ3H

UTC4125-02

126974-02

PCI1552-02

1515N100K102LEXH

10HV01N100KM

03

SV01AA120JHA

1515CN120JA102

102H42N120JQ3H

UTC4125-03

126974-03

PCI1552-03

1515N120J102LEXH

10HV01N120JM

04

SV01AA120KHA

1515CN120KA102

102H42N120KQ3H

UTC4125-04

126974-04

PCI1552-04

1515N120K102LEXH

10HV01N120KM

05

SV01AA150JHA

1515CN150JA102

102H42N150JQ3H

UTC4125-05

126974-05

PCI1552-05

1515N150J102LEXH

10HV01N150JM

06

SV01AA150KHA

1515CN150KA102

102H42N150KQ3H

UTC4125-06

126974-06

PCI1552-06

1515N150K102LEXH

10HV01N150KM

07

SV01AA180JHA

1515CN180JA102

102H42N180JQ3H

UTC4125-07

126974-07

PCI1552-07

1515N180J102LEXH

10HV01N180JM

08

SV01AA180KHA

1515CN180KA102

102H42N180KQ3H

UTC4125-08

126974-08

PCI1552-08

1515N180K102LEXH

10HV01N180KM

09

SV01AA220JHA

1515CN220JA102

102H42N220JQ3H

UTC4125-09

126974-09

PCI1552-09

1515N220J102LEXH

10HV01N220JM

10

SV01AA220KHA

1515CN220KA102

102H42N220KQ3H

UTC4125-10

126974-10

PCI1552-10

1515N220K102LEXH

10HV01N220KM

11

SV01AA270JHA

1515CN270JA102

102H42N270JQ3H

UTC4125-11

126974-11

PCI1552-11

1515N270J102LEXH

10HV01N270JM

12

SV01AA270KHA

1515CN270KA102

102H42N270KQ3H

UTC4125-12

126974-12

PCI1552-12

1515N270K102LEXH

10HV01N270KM

13

SV01AA330JHA

1515CN330JA102

102H42N330JQ3H

UTC4125-13

126974-13

PCI1552-13

1515N330J102LEXH

10HV01N330JM

14

SV01AA330KHA

1515CN330KA102

102H42N330KQ3H

UTC4125-14

126974-14

PCI1552-14

1515N330K102LEXH

10HV01N330KM

15

SV01AA390JHA

1515CN390JA102

102H42N390JQ3H

UTC4125-15

126974-15

PCI1552-15

1515N390J102LEXH

10HV01N390JM

16

SV01AA390KHA

1515CN390KA102

102H42N390KQ3H

UTC4125-16

126974-16

PCI1552-16

1515N390K102LEXH

10HV01N390KM

17

SV01AA470JHA

1515CN470JA102

102H42N470JQ3H

UTC4125-17

126974-17

PCI1552-17

1515N470J102LEXH

10HV01N470JM

18

SV01AA470KHA

1515CN470KA102

102H42N470KQ3H

UTC4125-18

126974-18

PCI1552-18

1515N470K102LEXH

10HV01N470KM

19

SV01AA560JHA

1515CN560JA102

102H42N560JQ3H

UTC4125-19

126974-19

PCI1552-19

1515N560J102LEXH

10HV01N560JM

20

SV01AA560KHA

1515CN560KA102

102H42N560KQ3H

UTC4125-20

126974-20

PCI1552-20

1515N560K102LEXH

10HV01N560KM

21

SV01AA680JHA

1515CN680JA102

102H42N680JQ3H

UTC4125-21

126974-21

PCI1552-21

1515N680J102LEXH

10HV01N680JM

22

SV01AA680KHA

1515CN680KA102

102H42N680KQ3H

UTC4125-22

126974-22

PCI1552-22

1515N680K102LEXH

10HV01N680KM

23

SV01AA820JHA

1515CN820JA102

102H42N820JQ3H

UTC4125-23

126974-23

PCI1552-23

1515N820J102LEXH

10HV01N820JM

24

SV01AA820KHA

1515CN820KA102

102H42N820KQ3H

UTC4125-24

126974-24

PCI1552-24

1515N820K102LEXH

10HV01N820KM

25

SV01AA101JHA

1515CN101JA102

102H42N101JQ3H

UTC4125-25

126974-25

PCI1552-25

1515N101J102LEXH

10HV01N101JM

26

SV01AA101KHA

1515CN101KA102

102H42N101KQ3H

UTC4125-26

126974-26

PCI1552-26

1515N101K102LEXH

10HV01N101KM

27

SV01AA121JHA

1515CN121JA102

102H42N121JQ3H

UTC4125-27

126974-27

PCI1552-27

1515N121J102LEXH

10HV01N121JM

28

SV01AA121KHA

1515CN121KA102

102H42N121KQ3H

UTC4125-28

126974-28

PCI1552-28

1515N121K102LEXH

10HV01N121KM

29

SV01AA151JHA

1515CN151JA102

102H42N151JQ3H

UTC4125-29

126974-29

PCI1552-29

1515N151J102LEXH

10HV01N151JM

30

SV01AA151KHA

1515CN151KA102

102H42N151KQ3H

UTC4125-30

126974-30

PCI1552-30

1515N151K102LEXH

10HV01N151KM

31

SV01AA181JHA

1515CN181JA102

102H42N181JQ3H

UTC4125-31

126974-31

PCI1552-31

1515N181J102LEXH

10HV01N181JM

32

SV01AA181KHA

1515CN181KA102

102H42N181KQ3H

UTC4125-32

126974-32

PCI1552-32

1515N181K102LEXH

10HV01N181KM

33

SV01AA221JHA

1515CN221JA102

102H42N221JQ3H

UTC4125-33

126974-33

PCI1552-33

1515N221J102LEXH

10HV01N221JM

34

SV01AA221KHA

1515CN221KA102

102H42N221KQ3H

UTC4125-34

126974-34

PCI1552-34

1515N221K102LEXH

10HV01N221KM

35

SV01AA271JHA

1515CN271JA102

102H42N271JQ3H

UTC4125-35

126974-35

PCI1552-35

1515N271J102LEXH

10HV01N271JM

36

SV01AA271KHA

1515CN271KA102

102H42N271KQ3H

UTC4125-36

126974-36

PCI1552-36

1515N271K102LEXH

10HV01N271KM

37

SV01AA331JHA

1515CN331JA102

102H42N331JQ3H

UTC4125-37

126974-37

PCI1552-37

1515N331J102LEXH

10HV01N331JM

38

SV01AA331KHA

1515CN331KA102

102H42N331KQ3H

UTC4125-38

126974-38

PCI1552-38

1515N331K102LEXH

10HV01N331KM

39

SV01AA391JHA

1515CN391JA102

102H42N391JQ3H

UTC4125-39

126974-39

PCI1552-39

1515N391J102LEXH

10HV01N391JM

40

SV01AA391KHA

1515CN391KA102

102H42N391KQ3H

UTC4125-40

126974-40

PCI1552-40

1515N391K102LEXH

10HV01N391KM

41

SV01AA471JHA

1515CN471JA102

102H42N471JQ3H

UTC4125-41

126974-41

PCI1552-41

1515N471J102LEXH

10HV01N471JM

42

SV01AA471KHA

1515CN471KA102

102H42N471KQ3H

UTC4125-42

126974-42

PCI1552-42

1515N471K102LEXH

10HV01N471KM

43

SV01AA561JHA

1515CN561JA102

102H42N561JQ3H

UTC4125-43

126974-43

PCI1552-43

1515N561J102LEXH

10HV01N561JM

44

SV01AA561KHA

1515CN561KA102

102H42N561KQ3H

UTC4125-44

126974-44

PCI1552-44

1515N561K102LEXH

10HV01N561KM

45

SV01AA681JHA

1515CN681JA102

102H42N681JQ3H

UTC4125-45

126974-45

PCI1552-45

1515N681J102LEXH

10HV01N681JM

46

SV01AA681KHA

1515CN681KA102

102H42N681KQ3H

UTC4125-46

126974-46

PCI1552-46

1515N681K102LEXH

10HV01N681KM

47

SV01AA821JHA

1515CN821JA102

102H42N821JQ3H

UTC4125-47

126974-47

PCI1552-47

1515N821J102LEXH

10HV01N821JM

48

SV01AA821KHA

1515CN821KA102

102H42N821KQ3H

UTC4125-48

126974-48

PCI1552-48

1515N821K102LEXH

10HV01N821KM

See footnote at end of table.

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHI O

SIZE

A

REV N

CODE IDENT NO.

14933

PAGE 7

DWG NO.

87046

1/ DSCC

drawing

87046-

Vendor A

similar

vendor type

Vendor B

similar

vendor type

Vendor C and J

similar

vendor type

Vendor D

similar

vendor type

Vendor E

similar

vendor type

Vendor F

similar

vendor type

Vendor G

similar

vendor type

Vendor H

similar

vendor type

49

SV01AA102JHA

1515CN102JA102

102H42N102JQ3H

UTC4125-49

126974-49

PCI1552-49

1515N102J102LEXH

10HV01N102JM

50

SV01AA102KHA

1515CN102KA102

102H42N102KQ3H

UTC4125-50

126974-50

PCI1552-50

1515N102K102LEXH

10HV01N102KM

51

SV02AA122JHA

2020CN122JA102

102H46N122JQ3H

UTC4125-51

126974-51

PCI1552-51

2020N122J102LEXH

10HV02N122JM

52

SV02AA122KHA

2020CN122KA102

102H46N122KQ3H

UTC4125-52

126974-52

PCI1552-52

2020N122K102LEXH

10HV02N122KM

53

SV02AA152JHA

2020CN152JA102

102H46N152JQ3H

UTC4125-53

126974-53

PCI1552-53

2020N152J102LEXH

10HV02N152JM

54

SV02AA152KHA

2020CN152KA102

102H46N152KQ3H

UTC4125-54

126974-54

PCI1552-54

2020N152K102LEXH

10HV02N152KM

55

SV02AA182JHA

2020CN182JA102

102H46N182JQ3H

UTC4125-55

126974-55

PCI1552-55

2020N182J102LEXH

10HV02N182JM

56

SV02AA182KHA

2020CN182KA102

102H46N182KQ3H

UTC4125-56

126974-56

PCI1552-56

2020N182K102LEXH

10HV02N182KM

57

SV03AA222JHA

2520CN222JA102

102H47N222JQ3H

UTC4125-57

126974-57

PCI1552-51

2520N222J102LEXH

10HV03N222JM

58

SV03AA222KHA

2520CN222KA102

102H47N222KQ3H

UTC4125-58

126974-58

PCI1552-52

2520N222K102LEXH

10HV03N222KM

59

SV05AA272JHA

3530CN272KA102

102H51N272JQ3H

UTC4125-59

126974-59

PCI1552-53

3530N272J102LEXH

10HV04N272JM

60

SV05AA272KHA

3530CN272JA102

102H51N272KQ3H

UTC4125-60

126974-60

PCI1552-54

3530N272K102LEXH

10HV04N272KM

61

SV05AA332JHA

3530CN332JA102

102H51N332JQ3H

UTC4125-61

126974-61

PCI1552-55

3530N332J102LEXH

10HV04N332JM

62

SV05AA332KHA

3530CN332KA102

102H51N332KQ3H

UTC4125-62

126974-62

PCI1552-62

3530N332K102LEXH

10HV04N332KM

63

SV05AA392JHA

3530CN392JA102

102H51N392JQ3H

UTC4125-63

126974-63

PCI1552-63

3530N392J102LEXH

10HV04N392JM

64

SV05AA392KHA

3530CN392KA102

102H51N392KQ3H

UTC4125-64

126974-64

PCI1552-64

3530N392K102LEXH

10HV04N392KM

65

SV05AA472JHA

3530CN472JA102

102H51N472JQ3H

UTC4125-65

126974-65

PCI1552-65

3530N472J102LEXH

10HV04N472JM

66

SV05AA472KHA

3530CN472KA102

102H51N472KQ3H

UTC4125-66

126974-66

PCI1552-66

3530N472K102LEXH

10HV04N472KM

67

SV07AA562JHA

4540CN562JA102

102H62N562JQ3H

UTC4125-67

126974-67

PCI1552-67

4540N562J102LEXH

10HV05N562JM

68

SV07AA562KHA

4540CN562KA102

102H62N562KQ3H

UTC4125-68

126974-68

PCI1552-68

4540N562K102LEXH

10HV05N562KM

69

SV07AA682JHA

4540CN682JA102

102H62N682JQ3H

UTC4125-69

126974-69

PCI1552-69

4540N682J102LEXH

10HV05N682JM

70

SV07AA682KHA

4540CN682KA102

102H62N682KQ3H

UTC4125-70

126974-70

PCI1552-70

4540N682K102LEXH

10HV05N682KM

71

SV07AA822JHA

4540CN822JA102

102H62N822JQ3H

UTC4125-71

126974-71

PCI1552-71

4540N822J102LEXH

10HV05N822JM

72

SV07AA822KHA

4540CN822KA102

102H62N822KQ3H

UTC4125-72

126974-72

PCI1552-72

4540N822K102LEXH

10HV05N822KM

73

SV07AA103JHA

4540CN103JA102

102H62N103JQ3H

UTC4125-73

126974-73

PCI1552-73

4540N103J102LEXH

10HV05N103JM

74

SV07AA103KHA

4540CN103KA102

102H62N103KQ3H

UTC4125-74

126974-74

PCI1552-74

4540N103K102LEXH

10HV05N103KM

75

SV08AA123JHA

5550CN123JA102

102H66N123JQ3H

UTC4125-75

126974-75

PCI1552-75

5550N123J102LEXH

10HV06N123JM

76

SV08AA123KHA

5550CN123KA102

102H66N123KQ3H

UTC4125-76

126974-76

PCI1552-76

5550N123K102LEXH

10HV06N123KM

77

SV08AA153JHA

5550CN153JA102

102H66N153JQ3H

UTC4125-77

126974-77

PCI1552-77

5550N153J102LEXH

10HV06N153JM

78

SV08AA153KHA

5550CN153KA102

102H66N153KQ3H

UTC4125-78

126974-78

PCI1552-78

5550N153K102LEXH

10HV06N153KM

79

SV08AA183JHA

5550CN183JA102

102H66N183JQ3H

UTC4125-79

126974-79

PCI1552-79

5550N183J102LEXH

10HV06N183JM

80

SV08AA183KHA

5550CN183KA102

102H66N183KQ3H

UTC4125-80

126974-80

PCI1552-80

5550N183K102LEXH

10HV06N183KM

81

SV09AA223JHA

6560CN223JA102

102H70N223JQ3H

UTC4125-81

126974-81

PCI1552-81

6560N223J102LEXH

10HV07N223JM

82

SV09AA223KHA

6560CN223KA102

102H70N223KQ3H

UTC4125-82

126974-82

PCI1552-82

6560N223K102LEXH

10HV07N223KM

83

SV09AA253JHA

6560CN253JA102

102H70N253JQ3H

UTC4125-83

126974-83

PCI1552-83

6560N253J102LEXH

10HV07N253JM

84

SV09AA253KHA

6560CN253KA102

102H70N253KQ3H

UTC4125-84

126974-84

PCI1552-84

6560N253K102LEXH

10HV07N253KM

1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met.

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHI O

SIZE

A

REV N

CODE IDENT NO.

14933

PAGE 8

DWG NO.

87046

DEFENSE ELECTRONICS SUPPLY CENTER

DAYTON, OHIO

SIZE

A

CODE IDENT NO.

14933

DWG NO.

87046

REV N PAGE 9

6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become

available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus,

OH 43218-3990 or e-mailed to capacitorfilter@dla.mil also by telephone (614) 692-4709 or DSN 850-4709.

VENDOR VENDOR CAGE VENDOR NAME AND ADDRESS

A 96095 Olean Advanced Products

A Division of AVX Corporation

1695 Seneca Avenue

Olean NY 14760-3736

B 63980 Wright Capacitors Incorporated

2610 South Oak Street

Santa Ana CA 92707-3720

C 07EN1 Advanced Monolythic Ceramics, Incorporated

3101 Constitution Avenue, Suite 100

Olean NY 14760-1867

D 0YBX7 Union Technology Corporation

718 Monterey Pass Road

Monterey Park CA 91754-3607

E 0LR95 Spectrum Control Technology Incorporated

1900 West College Avenue

State College, PA 16801

F 60212 Presidio Components Incorporated

7169 Construction Court

San Diego CA 92121-2615

G 65238 Novacap

25136 Anza Drive

Valencia CA 91355-3415

H 3H3G4 CalRamic Technologies LLC

5462 Louie Lane

Reno, NV 89511

J 29454 Johanson Dielectrics, Inc

15191 Bledsoe Avenue

Sylmar, CA 91342