ALUMINUM ELECTROLYTIC CAPACITORS
1
Voltage
Capacitance
105°C Marking
105°C Marking
(φ3 ~ φ8 × 5.4L)
(φ8 × 10L, φ10 × 10L)
A2P
10
16V
Plastic platform
0.3MAX.
L
(L±0.3)
+0.1
–0.2
φD±0.5
B±0.2
C±0.2
0.5MAX.
A±0.2 A±0.2
E
H
H
Positive
Negative
1
Voltage
Capacitance
Trade mark
Lot No.
A2P
100
35V
Plastic platform
0.3MAX.
L±0.5
Pressure relief vent
1. Voltage mark for 6.3V is 6V . In case of marking for φ3 units, “V” for rated
voltage is omitted.
2. In case of marking for φ3 units. Lot No is expressed by a digit (month code).
3 Apply to φ6.3 × 5.8, φ6.3 × 7.7
φD±0.5
B±0.2
C±0.2
0.5MAX.
A±0.2 A±0.2
E
Positive
Negative
Lot No.
2
3
U
1W
2T
31
4C
51
60
70
8M
9C
10 R
11 1
12 G
13 B
14
Configuration
Package code
Case dia. code
Capacitance tolerance (±20%)
Rated Capacitance (10µF)
Rated voltage (16V)
Series name
Type
φD
3
4 ~ 10
code
2
1
φD
3 ~ 8 (5.4L)
6.3 ~ 10 (L 5.8)
code
GB
GS
φD
3 ~ 8 (L 7.7)
8 ~ 10 (L = 10)
code
CR
NR
A
B
C
E
L
H
3 × 5.4
1.5
3.3
3.3
0.8
5.4
0.5 ~ 0.8
4 × 5.4
1.8
4.3
4.3
1.0
5.4
0.5 ~ 0.8
5 × 5.4
2.1
5.3
5.3
1.3
5.4
0.5 ~ 0.8
6.3 × 5.4
2.4
6.6
6.6
2.2
5.4
0.5 ~ 0.8
6.3 × 5.8
2.4
6.6
6.6
2.2
5.8
0.5 ~ 0.8
6.3 × 7.7
2.4
6.6
6.6
2.2
7.7
0.5 ~ 0.8
8 × 5.4
3.3
8.3
8.3
2.3
5.4
0.5 ~ 0.8
8 × 10
2.9
8.3
8.3
3.1
10
0.8 ~ 1.1
10 × 10
3.2
10.3
10.3
4.5
10
0.8 ~ 1.1
WT series
Chip Type, Wide Temperature Range
Chip type operating over wide temperature range of to –55 ~ +105
°C
.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Chip Type Type numbering system (Example : 16V 10
µ
F)
Specifications
Category
Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
tan δ
Stability at Low Temperature
Endurance
Shelf Life
Marking
Performance CharacteristicsItem –55 ~ +105°C
4 ~ 50V
0.1 ~ 1500µF
±20% at 120Hz, 20°C
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Black print on the case top.
Measurement frequency : 120Hz, Temperature : 20°C
Measurement frequency : 120Hz
After 1000 hours' application of rated voltage
at 105°C, capacitors meet the characteristic
requirements listed at right.
After leaving capacitors under no load at 105°C for 1000 hours,
they meet the specified value for endurance characteristics listed above.
Resistance to soldering
heat
The capacitors shall be kept on the hot plate maintained at 250°C
for 30 seconds. After removing from the hot plate and restored
at room temperature, they meet the characteristic requirements
listed at right.
Rated voltage (V)
tan δ(MAX.)
4
0.40 6.3
0.30 10
0.24 16
0.20 25
0.16 35
0.14 50
0.14
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
4
7
15
6.3
4
8
10
3
8
16
2
4
25
2
4
35
2
3
50
2
3
WT
WX
Capacitance
change
Leakage current
tan δ
Within ±25% of initial value for capacitors of φ3mm unit, and 16V or less.
Within ±20% of initial value for capacitors of 25V or more.
200% or less of initial specified value
Initial specified value or less
Capacitance change
Leakage current
tan δ
Within ±10% of initial value
Initial specified value or less
Initial specified value or less
High
Tempe rature
Dimension table in next page. CAT.8100R
CAT.8100R
ALUMINUM ELECTROLYTIC CAPACITORS
WT series
Dimensions
Rated Ripple (mA rms) at 105°C 120Hz
( ) is also available with
φ
3mm upon request. In such a case, will be put at 12th digit of type numbering system.
Size φ6.3 × 5.8 is available for capacitors marked. " " In such a case, will be put at 12th digit of type numbering system.
6
2
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
150
220
330
470
680
1000
1500
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
151
221
331
471
681
102
152
4× 5.4
5× 5.4
5× 5.4
6.3 × 5.4
6.3 × 5.8
8× 5.4
6.3 × 7.7
8× 10
8× 10
8× 10
10 × 10
22
30
36
60
86
102
(91)
105
210
210
230
310
0G
V40J
6.3 1A
10 1C
16 1E
25 1V
35 1H
50
4× 5.4
5× 5.4
5× 5.4
6.3 × 5.4
6.3 × 5.8
8× 5.4
6.3 × 7.7
8× 10
8× 10
8× 10
10 × 10
5× 5.4
5× 5.4
6.3 × 5.4
6.3 × 5.4
6.3 × 5.8
6.3 × 7.7
8× 10
8× 10
10 × 10
10 × 10
4× 5.4
(3)
5× 5.4
6.3 × 5.4
6.3 × 5.4
6.3 × 5.4
6.3 × 7.7
6.3 × 7.7
8× 10
8× 10
10 × 10
4× 5.4
(3)
5× 5.4
6.3 × 5.4
6.3 × 5.4
8× 5.4
6.3 × 7.7
8× 10
8× 10
8× 10
10 × 10
3× 5.4
3× 5.4
4× 5.4
5× 5.4
6.3 × 5.4
8× 5.4
6.3 × 5.8
6.3 × 7.7
8× 10
8× 10
10 × 10
4× 5.4
(3)
4× 5.4
(3)
4× 5.4
(3)
4× 5.4
(3)
4× 5.4
(3)
4× 5.4
(3)
4× 5.4
5× 5.4
6.3 × 5.4
8× 5.4
6.3 × 7.7
6.3 × 7.7
8× 10
10 × 10
10 × 10
Case size
22
30
36
60
86
102
(91)
105
210
210
230
310
27
35
46
60
86
105
195
210
310
310
18
(14)
30
40
50
60
95
105
195
230
310
13
(10)
23
38
48
66
(59)
91
140
155
190
300
7.5
9
15
25
42
59
(52)
63
84
155
190
300
1.0
2.6
3.2
3.8
6.3 (5.9)
11 (9)
14
19
30
51
(45)
60
63
140
180
220
Code
Cap. (µF)
Rated
ripple
Please refer to page 3 for the minimum order quantity.
Taping Specifications are given in page 21.
Frequency coefficient of rated ripple current
Coefficient
Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz~
0.70 1.00 1.17 1.36 1.50
