ALUMINUM ELECTROLYTIC CAPACITORS WT Chip Type, Wide Temperature Range series Chip type operating over wide temperature range of to - 55 ~ +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. WT High Temperature WX Specifications Item Performance Characteristics Category Temperature Range - 55 ~ +105C Rated Voltage Range 4 ~ 50V Rated Capacitance Range 0.1 ~ 1500F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20C tan Rated voltage (V) tan (MAX.) 4 0.40 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z- 25C / Z+20C Impedance ratio Z- 40C / Z+20C ZT / Z20 (MAX.) After 1000 hours' application of rated voltage at 105C, capacitors meet the characteristic requirements listed at right. Endurance Shelf Life Resistance to soldering heat 4 7 15 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Within 25% of initial value for capacitors of 3mm unit, and 16V or less. Within 20% of initial value for capacitors of 25V or more. 200% or less of initial specified value Leakage current Initial specified value or less Capacitance change tan After leaving capacitors under no load at 105C for 1000 hours, they meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250C Capacitance change for 30 seconds. After removing from the hot plate and restored tan at room temperature, they meet the characteristic requirements Leakage current listed at right. Within 10% of initial value Initial specified value or less Initial specified value or less Black print on the case top. Marking Type numbering system (Example : 16V 10F) Chip Type (3 ~ 8 x 5.4L) Positive L 2 Lot No. 1 0.5 MAX. 2 3 4 5 6 7 8 Package code Case dia. code Configuration A0.2 Capacitance tolerance (20%) Rated Capacitance (10F) +0.1 -0.2 (L0.3) Negative H 3 D code 3 ~ 8 (5.4L) GB 6.3 ~ 10 (L 5.8) GS 9 10 11 12 13 14 UWT 1 C 1 0 0 MC R 1 GB A0.2 C0.2 E A2P 10 16V 105C Marking Plastic platform 0.3 MAX. D0.5 1 Voltage B0.2 Capacitance D 3 ~ 8 (L 7.7) 8 ~ 10 (L = 10) code CR NR D 3 4 ~ 10 code 2 1 Rated voltage (16V) 3 Apply to 6.3 x 5.8, 6.3 x 7.7 Series name Type (8 x 10L, 10 x 10L) A0.2 C0.2 A0.2 L0.5 Lot No. Pressure relief vent 8 x 10 10 x 10 3.3 2.9 3.2 5 x 5.4 6.3 x 5.4 6.3 x 5.8 6.3 x 7.7 8 x 5.4 3 x 5.4 4 x 5.4 A 1.5 1.8 2.1 2.4 2.4 2.4 E B0.2 A2P 100 35V D0.5 1 Voltage 105C Marking Trade mark Plastic platform 0.3 MAX. 0.5 MAX. Positive Capacitance B 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 C 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 E 0.8 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 L 5.4 5.4 5.4 5.4 5.8 7.7 5.4 10 10 Negative H 1. Voltage mark for 6.3V is 6V . In case of marking for 3 units, "V" for rated voltage is omitted. 2. In case of marking for 3 units. Lot No is expressed by a digit (month code). H 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 Dimension table in next page. CAT.8100R ALUMINUM ELECTROLYTIC CAPACITORS WT series Dimensions V Cap. (F) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 150 220 330 470 680 1000 1500 Code 4 0G 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 4 x 5.4 220 5 x 5.4 330 5 x 5.4 470 101 6.3 x 5.4 151 6.3 x 5.8 8 x 5.4 221 331 6.3 x 7.7 8 x 10 471 8 x 10 681 8 x 10 102 152 10 x 10 6.3 0J 4 x 5.4 22 5 x 5.4 30 5 x 5.4 36 6.3 x 5.4 60 6.3 x 5.8 86 8 x 5.4 102 (91) 6.3 x 7.7 105 8 x 10 210 8 x 10 210 8 x 10 230 10 x 10 310 10 1A 22 30 36 60 86 102 (91) 105 210 210 230 310 5 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 5.4 6.3 x 5.8 6.3 x 7.7 8 x 10 8 x 10 10 x 10 10 x 10 16 1C 27 35 46 60 86 105 195 210 310 310 25 1E 35 1V 3 x 5.4 3 x 5.4 4 x 5.4 4 x 5.4 (3) 13 (10) 5 x 5.4 4 x 5.4 (3) 18 (14) 5 x 5.4 23 6.3 x 5.4 5 x 5.4 30 6.3 x 5.4 38 8 x 5.4 6.3 x 5.4 40 6.3 x 5.4 48 6.3 x 5.4 8 x 5.4 50 66 (59) 6.3 x 5.8 91 6.3 x 7.7 6.3 x 5.4 6.3 x 7.7 60 8 x 10 6.3 x 7.7 8 x 10 140 95 8 x 10 6.3 x 7.7 105 8 x 10 155 10 x 10 8 x 10 195 8 x 10 190 8 x 10 230 10 x 10 300 10 x 10 310 ( ) is also available with 3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system. Size 6.3 x 5.8 is available for capacitors marked. " " In such a case, 6 will be put at 12th digit of type numbering system. 50 1H 4 x 5.4 (3) 1.0 4 x 5.4 (3) 2.6 4 x 5.4 (3) 3.2 4 x 5.4 (3) 3.8 4 x 5.4 (3) 6.3 (5.9) 4 x 5.4 (3) 11 (9) 7.5 9 4 x 5.4 14 5 x 5.4 19 15 6.3 x 5.4 25 30 8 x 5.4 42 51 (45) 60 59 (52) 6.3 x 7.7 63 63 6.3 x 7.7 84 8 x 10 140 155 10 x 10 180 190 10 x 10 220 300 Rated Case size ripple Rated Ripple (mA rms) at 105C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping Specifications are given in page 21. Please refer to page 3 for the minimum order quantity. CAT.8100R