www.fairchildsemi.com ML4824 Power Factor Correction and PWM Controller Combo Features General Description * Internally synchronized PFC and PWM in one IC * Low total harmonic distortion * Reduces ripple current in the storage capacitor between the PFC and PWM sections * Average current, continuous boost leading edge PFC * Fast transconductance error amp for voltage loop * High efficiency trailing edge PWM can be configured for current mode or voltage mode operation * Average line voltage compensation with brownout control * PFC overvoltage comparator eliminates output "runaway" due to load removal * Current fed gain modulator for improved noise immunity * Overvoltage protection, UVLO, and soft start The ML4824 is a controller for power factor corrected, switched mode power supplies. Power Factor Correction (PFC) allows the use of smaller, lower cost bulk capacitors, reduces power line loading and stress on the switching FETs, and results in a power supply that fully complies with IEC1000-2-3 specification. The ML4824 includes circuits for the implementation of a leading edge, average current, "boost" type power factor correction and a trailing edge, pulse width modulator (PWM). The device is available in two versions; the ML4824-1 (fPWM = fPFC) and the ML4824-2 (fPWM = 2 x fPFC). Doubling the switching frequency of the PWM allows the user to design with smaller output components while maintaining the best operating frequency for the PFC. An over-voltage comparator shuts down the PFC section in the event of a sudden decrease in load. The PFC section also includes peak current limiting and input voltage brown-out protection. The PWM section can be operated in current or voltage mode at up to 250kHz and includes a duty cycle limit to prevent transformer saturation. Block Diagram 16 VFB VEA - 15 2.5V 13 1 IEAO VEAO 3.5k POWER FACTOR CORRECTOR VCC VCCZ OVP + IEA + 2.7V + + 13.5V - - IAC - 2 -1V 4 - Q R Q S Q R Q S Q R Q 14 PFC OUT 3.5k ISENSE S VREF + GAIN MODULATOR VRMS 7.5V REFERENCE PFC ILIMIT 12 3 RAMP 1 OSCILLATOR 7 (-2 VERSION ONLY) RAMP 2 x2 DUTY CYCLE LIMIT 8 8V VDC 6 1.25V + VCC SS - PWM OUT - 50A 5 + VFB - 2.5V + VIN OK 1V 8V - + 11 DC ILIMIT DC ILIMIT 9 PULSE WIDTH MODULATOR VCCZ UVLO REV. 1.0.6 11/7/03 ML4824 PRODUCT SPECIFICATION Pin Configuration ML4824 16-Pin PDIP (P16) 16-Pin Wide SOIC (S16W) IEAO 1 16 VEAO IAC 2 15 VFB ISENSE 3 14 VREF VRMS 4 13 VCC SS 5 12 PFC OUT VDC 6 11 PWM OUT RAMP 1 7 10 GND RAMP 2 8 9 DC ILIMIT TOP VIEW Pin Description PIN 2 NAME FUNCTION 1 IEAO PFC transconductance current error amplifier output 2 IAC PFC gain control reference input 3 ISENSE Current sense input to the PFC current limit comparator 4 VRMS Input for PFC RMS line voltage compensation 5 SS Connection point for the PWM soft start capacitor 6 VDC PWM voltage feedback input 7 RAMP 1 Oscillator timing node; timing set by RTCT 8 RAMP 2 When in current mode, this pin functions as as the current sense input; when in voltage mode, it is the PWM input from PFC output (feed forward ramp). 9 DC ILIMIT PWM current limit comparator input 10 GND Ground 11 PWM OUT PWM driver output 12 PFC OUT PFC driver output 13 VCC Positive supply (connected to an internal shunt regulator) 14 VREF Buffered output for the internal 7.5V reference 15 VFB PFC transconductance voltage error amplifier input 16 VEAO PFC transconductance voltage error amplifier output REV. 1.0.6 11/7/03 PRODUCT SPECIFICATION ML4824 Absolute Maximum Ratings Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Parameter Min. Max. Units 55 mA -3 5 V GND - 0.3 VCCZ + 0.3 V IREF 20 mA IAC Input Current 10 mA Peak PFC OUT Current, Source or Sink 500 mA Peak PWM OUT Current, Source or Sink 500 mA PFC OUT, PWM OUT Energy Per Cycle 1.5 J 150 C 150 C Lead Temperature (Soldering, 10 sec) 260 C Thermal Resistance (JA) Plastic DIP Plastic SOIC 80 105 C/W C/W VCC Shunt Regulator Current ISENSE Voltage Voltage on Any Other Pin Junction Temperature Storage Temperature Range -65 Operating Conditions Temperature Range Parameter Min. Max. Units ML4824CX 0 70 C ML4824IX -40 85 C Electrical Characteristics Unless otherwise specified, ICC = 25mA, RT = 52.3k, CT = 470pF, TA = Operating Temperature Range (Note 1) Symbol Parameter Conditions Min. Typ. Max. Units 0 7 Voltage Error Amplifier Transconductance VNON INV = VINV, VEAO = 3.75V Feedback Reference Voltage Input Bias Current 50 85 120 2.46 2.53 2.60 V -0.3 -1.0 A Note 2 Output High Voltage V Input Voltage Range 6.0 Output Low Voltage 6.7 0.6 V 1.0 V Source Current VIN = 0.5V, VOUT = 6V -40 -80 A Sink Current VIN = 0.5V, VOUT = 1.5V 40 80 A 60 75 dB 60 75 dB Open Loop Gain Power Supply Rejection Ratio VCCZ - 3V < VCC < VCCZ - 0.5V Current Error Amplifier Transconductance Input Offset Voltage REV. 1.0.6 11/7/03 -1.5 VNON INV = VINV, VEAO = 3.75V 2 V Input Voltage Range 130 195 310 0 8 15 mV 3 ML4824 PRODUCT SPECIFICATION Electrical Characteristics (continued) Unless otherwise specified, ICC = 25mA, RT = 52.3k, CT = 470pF, TA = Operating Temperature Range (Note 1) Symbol Parameter Conditions Min. Input Bias Current Typ. Max. Units -0.5 Output High Voltage 6.0 6.7 Output Low Voltage 0.6 -1.0 A V 1.0 V Source Current VIN = 0.5V, VOUT = 6V -40 -90 A Sink Current VIN = 0.5V, VOUT = 1.5V 40 90 A 60 75 dB 60 75 dB Threshold Voltage 2.6 2.7 2.8 V Hysteresis 80 115 150 mV Open Loop Gain Power Supply Rejection Ratio VCCZ - 3V < VCC < VCCZ - 0.5V OVP Comparator PFC ILIMIT Comparator Threshold Voltage -0.8 -1.0 -1.15 (PFC ILIMIT VTH - Gain Modulator Output) 100 190 Delay to Output V mV 150 300 ns DC ILIMIT Comparator Threshold Voltage 1.02 1.07 V Input Bias Current 0.97 0.3 1 A Delay to Output 150 300 ns VIN OK Comparator Threshold Voltage 2.4 2.5 2.6 V Hysteresis 0.8 1.0 1.2 V IAC = 100A, VRMS = VFB = 0V 0.36 0.55 0.66 IAC = 50A, VRMS = 1.2V, VFB = 0V 1.20 1.80 2.24 IAC = 50A, VRMS = 1.8V, VFB = 0V 0.55 0.80 1.01 IAC = 100A, VRMS = 3.3V, VFB = 0V 0.14 0.20 0.26 Gain Modulator Gain (Note 3) Bandwidth IAC = 100A Output Voltage IAC = 250A, VRMS = 1.15V, VFB = 0V Initial Accuracy TA = 25C Voltage Stability VCCZ - 3V < VCC < VCCZ - 0.5V 10 MHz 0.74 0.82 0.90 V 71 76 81 kHz Oscillator Temperature Stability Total Variation Line, Temp 1 % 2 % 68 Ramp Valley to Peak Voltage 84 2.5 kHz V Dead Time PFC Only 270 370 470 ns CT Discharge Current VRAMP 2 = 0V, VRAMP 1 = 2.5V 4.5 7.5 9.5 mA TA = 25C, I(VREF) = 1mA 7.4 7.5 7.6 V Reference Output Voltage 4 REV. 1.0.6 11/7/03 PRODUCT SPECIFICATION ML4824 Electrical Characteristics (continued) Unless otherwise specified, ICC = 25mA, RT = 52.3k, CT = 470pF, TA = Operating Temperature Range (Note 1) Symbol Parameter Conditions Min. Typ. Max. Units Line Regulation VCCZ - 3V < VCC < VCCZ - 0.5V 2 10 mV Load Regulation 1mA < I(VREF) < 20mA 2 15 mV Temperature Stability 0.4 7.35 % Total Variation Line, Load, Temp Long Term Stability TJ = 125C, 1000 Hours Minimum Duty Cycle VIEAO > 4.0V Maximum Duty Cycle VIEAO < 1.2V Output Low Voltage IOUT = -20mA 0.4 0.8 V IOUT = -100mA 0.8 2.0 V IOUT = 10mA, VCC = 8V 0.7 1.5 V 5 7.65 V 25 mV 0 % PFC Output High Voltage 90 IOUT = 20mA 10 IOUT = 100mA 9.5 95 % 10.5 V 10 V 50 ns Rise/Fall Time CL = 1000pF Duty Cycle Range ML4824-1 0-44 0-47 0-50 % ML4824-2 0-37 0-40 0-45 % PWM Output Low Voltage Output High Voltage Rise/Fall Time IOUT = -20mA 0.4 0.8 V IOUT = -100mA 0.8 2.0 V IOUT = 10mA, VCC = 8V 0.7 1.5 V IOUT = 20mA 10 10.5 V IOUT = 100mA 9.5 10 V 50 ns CL = 1000pF Supply Shunt Regulator Voltage (VCCZ) 12.8 13.5 14.4 100 300 V VCCZ Load Regulation 25mA < ICC < 55mA VCCZ Total Variation Load, Temp Start-up Current VCC = 11.8V, CL = 0 0.7 1.0 mA Operating Current VCC < VCCZ - 0.5V, CL = 0 16 19 mA 12.4 14.6 mV V Undervoltage Lockout Threshold 12 13 14 V Undervoltage Lockout Hysteresis 2.7 3.0 3.3 V Notes 1. Limits are guaranteed by 100% testing, sampling, or correlation with worst-case test conditions. 2. Includes all bias currents to other circuits connected to the VFB pin. 3. Gain = K x 5.3V; K = (IGAINMOD - IOFFSET) x IAC x (VEAO - 1.5V)-1. REV. 1.0.6 11/7/03 5 ML4824 PRODUCT SPECIFICATION 250 200 200 TRANSCONDUCTANCE ( ) 250 TRANSCONDUCTANCE ( ) Typical Performance Characteristics 150 100 50 150 100 50 0 1 0 2 4 3 0 -500 5 0 VFB (V) 500 IEA INPUT VOLTAGE (mV) Voltage Error Amplifier (VEA) Transconductance (gm) Current Error Amplifier (IEA) Transconductance (gm) VARIABLE GAIN BLOCK CONSTANT - K 400 300 200 100 0 0 1 2 3 4 5 VRMS (mV) Gain Modulator Transfer Characteristic (K) 16 1 IEAO VEAO VFB 15 2.5V VEA - 3.5k OVP + IEA + + + IAC VRMS ISENSE - -1V + - 2 4 2.7V - GAIN MODULATOR - S Q R Q S Q R Q PFC OUT 3.5k PFC ILIMIT 12 3 RAMP 1 7 OSCILLATOR Figure 1. PFC Section Block Diagram. 6 REV. 1.0.6 11/7/03 PRODUCT SPECIFICATION Functional Description The ML4824 consists of an average current controlled, continuous boost Power Factor Corrector (PFC) front end and a synchronized Pulse Width Modulator (PWM) back end. The PWM can be used in either current or voltage mode. In voltage mode, feedforward from the PFC output buss can be used to improve the PWM's line regulation. In either mode, the PWM stage uses conventional trailing-edge duty cycle modulation, while the PFC uses leading-edge modulation. This patented leading/trailing edge modulation technique results in a higher useable PFC error amplifier bandwidth, and can significantly reduce the size of the PFC DC buss capacitor. The synchronization of the PWM with the PFC simplifies the PWM compensation due to the controlled ripple on the PFC output capacitor (the PWM input capacitor). The PWM section of the ML4824-1 runs at the same frequency as the PFC. The PWM section of the ML4824-2 runs at twice the frequency of the PFC, which allows the use of smaller PWM output magnetics and filter capacitors while holding down the losses in the PFC stage power components. In addition to power factor correction, a number of protection features have been built into the ML4824. These include soft-start, PFC over-voltage protection, peak current limiting, brown-out protection, duty cycle limit, and undervoltage lockout. Power Factor Correction Power factor correction makes a non-linear load look like a resistive load to the AC line. For a resistor, the current drawn from the line is in phase with and proportional to the line voltage, so the power factor is unity (one). A common class of non-linear load is the input of most power supplies, which use a bridge rectifier and capacitive input filter fed from the line. The peak-charging effect which occurs on the input filter capacitor in these supplies causes brief high-amplitude pulses of current to flow from the power line, rather than a sinusoidal current in phase with the line voltage. Such supplies present a power factor to the line of less than one (i.e. they cause significant current harmonics of the power line frequency to appear at their input). If the input current drawn by such a supply (or any other non-linear load) can be made to follow the input voltage in instantaneous amplitude, it will appear resistive to the AC line and a unity power factor will be achieved. To hold the input current draw of a device drawing power from the AC line in phase with and proportional to the input voltage, a way must be found to prevent that device from loading the line except in proportion to the instantaneous line voltage. The PFC section of the ML4824 uses a boost-mode DC-DC converter to accomplish this. The input to the converter is the full wave rectified AC line voltage. No bulk filtering is applied following the bridge rectifier, so the input voltage to the boost converter ranges (at twice line frequency) from zero volts to the peak value of the AC input REV. 1.0.6 11/7/03 ML4824 and back to zero. By forcing the boost converter to meet two simultaneous conditions, it is possible to ensure that the current which the converter draws from the power line agrees with the instantaneous line voltage. One of these conditions is that the output voltage of the boost converter must be set higher than the peak value of the line voltage. A commonly used value is 385VDC, to allow for a high line of 270VACrms. The other condition is that the current which the converter is allowed to draw from the line at any given instant must be proportional to the line voltage. The first of these requirements is satisfied by establishing a suitable voltage control loop for the converter, which in turn drives a current error amplifier and switching output driver. The second requirement is met by using the rectified AC line voltage to modulate the output of the voltage control loop. Such modulation causes the current error amplifier to command a power stage current which varies directly with the input voltage. In order to prevent ripple which will necessarily appear at the output of the boost circuit (typically about 10VAC on a 385V DC level) from introducing distortion back through the voltage error amplifier, the bandwidth of the voltage loop is deliberately kept low. A final refinement is to adjust the overall gain of the PFC such to be proportional to 1/VIN2, which linearizes the transfer function of the system as the AC input voltage varies. Since the boost converter topology in the ML4824 PFC is of the current-averaging type, no slope compensation is required. PFC Section Gain Modulator Figure 1 shows a block diagram of the PFC section of the ML4824. The gain modulator is the heart of the PFC, as it is this circuit block which controls the response of the current loop to line voltage waveform and frequency, rms line voltage, and PFC output voltage. There are three inputs to the gain modulator. These are: 1. A current representing the instantaneous input voltage (amplitude and waveshape) to the PFC. The rectified AC input sine wave is converted to a proportional current via a resistor and is then fed into the gain modulator at IAC. Sampling current in this way minimizes ground noise, as is required in high power switching power conversion environments. The gain modulator responds linearly to this current. 2. A voltage proportional to the long-term rms AC line voltage, derived from the rectified line voltage after scaling and filtering. This signal is presented to the gain modulator at VRMS. The gain modulator's output is inversely proportional to VRMS2 (except at unusually low values of VRMS where special gain contouring takes over, to limit power dissipation of the circuit components under heavy brownout conditions). The relationship between VRMS and gain is called K, and is illustrated in the Typical Performance Characteristics. 7 ML4824 3. PRODUCT SPECIFICATION The output of the voltage error amplifier, VEAO. The gain modulator responds linearly to variations in this voltage. The output of the gain modulator is a current signal, in the form of a full wave rectified sinusoid at twice the line frequency. This current is applied to the virtual-ground (negative) input of the current error amplifier. In this way the gain modulator forms the reference for the current error loop, and ultimately controls the instantaneous current draw of the PFC from the power line. The general form for the output of the gain modulator is: I AC x VEAO x 1V I GAINMOD -------------------------------2 V RMS VREF PFC OUTPUT 16 VFB VEA - 2.5V + 15 IEA + + - IAC (1) 1 IEAO VEAO - 2 VRMS 4 GAIN MODULATOR ISENSE More exactly, the output current of the gain modulator is given by: I GAINMOD K x ( VEAO - 1.5V ) x I AC where K is in units of V-1. Note that the output current of the gain modulator is limited to 200A. Current Error Amplifier The current error amplifier's output controls the PFC duty cycle to keep the average current through the boost inductor a linear function of the line voltage. At the inverting input to the current error amplifier, the output current of the gain modulator is summed with a current which results from a negative voltage being impressed upon the ISENSE pin (current into ISENSE VSENSE/3.5k). The negative voltage on ISENSE represents the sum of all currents flowing in the PFC circuit, and is typically derived from a current sense resistor in series with the negative terminal of the input bridge rectifier. In higher power applications, two current transformers are sometimes used, one to monitor the ID of the boost MOSFET(s) and one to monitor the IF of the boost diode. As stated above, the inverting input of the current error amplifier is a virtual ground. Given this fact, and the arrangement of the duty cycle modulator polarities internal to the PFC, an increase in positive current from the gain modulator will cause the output stage to increase its duty cycle until the voltage on ISENSE is adequately negative to cancel this increased current. Similarly, if the gain modulator's output decreases, the output duty cycle will decrease, to achieve a less negative voltage on the ISENSE pin. Cycle-By-Cycle Current Limiter The ISENSE pin, as well as being a part of the current feedback loop, is a direct input to the cycle-by-cycle current limiter for the PFC section. Should the input voltage at this pin ever be more negative than -1V, the output of the PFC will be disabled until the protection flip-flop is reset by the clock pulse at the start of the next PFC power cycle. 8 3 Figure 2. Compensation Network Connections for the Voltage and Current Error Amplifiers Overvoltage Protection The OVP comparator serves to protect the power circuit from being subjected to excessive voltages if the load should suddenly change. A resistor divider from the high voltage DC output of the PFC is fed to VFB. When the voltage on VFB exceeds 2.7V, the PFC output driver is shut down. The PWM section will continue to operate. The OVP comparator has 125mV of hysteresis, and the PFC will not restart until the voltage at VFB drops below 2.58V. The VFB should be set at a level where the active and passive external power components and the ML4824 are within their safe operating voltages, but not so low as to interfere with the boost voltage regulation loop. Error Amplifier Compensation The PWM loading of the PFC can be modeled as a negative resistor; an increase in input voltage to the PWM causes a decrease in the input current. This response dictates the proper compensation of the two transconductance error amplifiers. Figure 2 shows the types of compensation networks most commonly used for the voltage and current error amplifiers, along with their respective return points. The current loop compensation is returned to VREF to produce a soft-start characteristic on the PFC: as the reference voltage comes up from zero volts, it creates a differentiated voltage on IEAO which prevents the PFC from immediately demanding a full duty cycle on its boost converter. There are two major concerns when compensating the voltage loop error amplifier; stability and transient response. Optimizing interaction between transient response and stability requires that the error amplifier's open-loop crossover frequency should be 1/2 that of the line frequency, or 23Hz for a 47Hz line (lowest anticipated international power frequency). The gain vs. input voltage of the REV. 1.0.6 11/7/03 PRODUCT SPECIFICATION ML4824 ML4824's voltage error amplifier has a specially shaped nonlinearity such that under steady-state operating conditions the transconductance of the error amplifier is at a local minimum. Rapid perturbations in line or load conditions will cause the input to the voltage error amplifier (VFB) to deviate from its 2.5V (nominal) value. If this happens, the transconductance of the voltage error amplifier will increase significantly, as shown in the Typical Performance Characteristics. This raises the gain-bandwidth product of the voltage loop, resulting in a much more rapid voltage loop response to such perturbations than would occur with a conventional linear gain characteristic. The current amplifier compensation is similar to that of the voltage error amplifier with the exception of the choice of crossover frequency. The crossover frequency of the current amplifier should be at least 10 times that of the voltage amplifier, to prevent interaction with the voltage loop. It should also be limited to less than 1/6th that of the switching frequency, e.g. 16.7kHz for a 100kHz switching frequency. EXAMPLE: For the application circuit shown in the data sheet, with the oscillator running at: 1 f OSC = 100kHz = ---------------t RAMP t RAMP = C T x R T x 0.51 = 1 x 10 -5 Solving for RT x CT yields 2 x 10-4. Selecting standard components values, CT = 470pF, and RT = 41.2k. The deadtime of the oscillator adds to the Maximum PWM Duty Cycle (it is an input to the Duty Cycle Limiter). With zero oscillator deadtime, the Maximum PWM Duty Cycle is typically 45%. In many applications, care should be taken that CT not be made so large as to extend the Maximum Duty Cycle beyond 50%. This can be accomplished by using a stable 470pF capacitor for CT. PWM SECTION There is a modest degree of gain contouring applied to the transfer characteristic of the current error amplifier, to increase its speed of response to current-loop perturbations. However, the boost inductor will usually be the dominant factor in overall current loop response. Therefore, this contouring is significantly less marked than that of the voltage error amplifier. This is illustrated in the Typical Performance Characteristics. For more information on compensating the current and voltage control loops, see Application Notes 33 and 34. Application Note 16 also contains valuable information for the design of this class of PFC. Oscillator (RAMP 1) The oscillator frequency is determined by the values of RT and CT, which determine the ramp and off-time of the oscillator output clock: 1 f OSC = --------------------------------------------------t RAMP + t DEADTIME (2) The deadtime of the oscillator is derived from the following equation: V REF - 1.25 t RAMP = C T x R T x In -------------------------------- V REF - 3.75 (3) at VREF = 7.5V: t RAMP = C T x R T x 0.51 The deadtime of the oscillator may be determined using: t DEADTIME 2.5V = ------------------ x C T = 490 x C T 5.1mA (4) The deadtime is so small (tRAMP >> tDEADTIME) that the operating frequency can typically be approximated by: 1 f OSC = ---------------t RAMP REV. 1.0.6 11/7/03 Pulse Width Modulator The PWM section of the ML4824 is straightforward, but there are several points which should be noted. Foremost among these is its inherent synchronization to the PFC section of the device, from which it also derives its basic timing (at the PFC frequency in the ML4824-1, and at twice the PFC frequency in the ML4824-2). The PWM is capable of current-mode or voltage mode operation. In current-mode applications, the PWM ramp (RAMP 2) is usually derived directly from a current sensing resistor or current transformer in the primary of the output stage, and is thereby representative of the current flowing in the converter's output stage. DC ILIMIT, which provides cycle-by-cycle current limiting, is typically connected to RAMP 2 in such applications. For voltage-mode operation or certain specialized applications, RAMP 2 can be connected to a separate RC timing network to generate a voltage ramp against which VDC will be compared. Under these conditions, the use of voltage feedforward from the PFC buss can assist in line regulation accuracy and response. As in current mode operation, the DC ILIMIT input is used for output stage overcurrent protection. No voltage error amplifier is included in the PWM stage of the ML4824, as this function is generally performed on the output side of the PWM's isolation boundary. To facilitate the design of optocoupler feedback circuitry, an offset has been built into the PWM's RAMP 2 input which allows VDC to command a zero percent duty cycle for input voltages below 1.25V. PWM Current Limit The DC ILIMIT pin is a direct input to the cycle-by-cycle current limiter for the PWM section. Should the input voltage at this pin ever exceed 1V, the output of the PWM will be disabled until the output flip-flop is reset by the clock pulse at the start of the next PWM power cycle. (5) 9 ML4824 PRODUCT SPECIFICATION VIN OK Comparator The VIN OK comparator monitors the DC output of the PFC and inhibits the PWM if this voltage on VFB is less than its nominal 2.5V. Once this voltage reaches 2.5V, which corresponds to the PFC output capacitor being charged to its rated boost voltage, the soft-start begins. PWM Control (RAMP 2) When the PWM section is used in current mode, RAMP 2 is generally used as the sampling point for a voltage representing the current in the primary of the PWM's output transformer, derived either by a current sensing resistor or a current transformer. In voltage mode, it is the input for a ramp voltage generated by a second set of timing components (RRAMP2, CRAMP2), which will have a minimum value of zero volts and should have a peak value of approximately 5V. In voltage mode operation, feedforward from the PFC output buss is an excellent way to derive the timing ramp for the PWM stage. Soft Start Start-up of the PWM is controlled by the selection of the external capacitor at SS. A current source of 50A supplies the charging current for the capacitor, and start-up of the PWM begins at 1.25V. Start-up delay can be programmed by the following equation:: 50A C SS = t DELAY x ---------------1.25V (6) where CSS is the required soft start capacitance, and tDELAY is the desired start-up delay. It is important that the time constant of the PWM soft-start allow the PFC time to generate sufficient output power for the PWM section. The PWM start-up delay should be at least 5ms. limit the current through the part to avoid overheating or destroying it. This can be easily done with a single resistor in series with the Vcc pin, returned to a bias supply of typically 18V to 20V. The resistor's value must be chosen to meet the operating current requirement of the ML4824 itself (19mA max) plus the current required by the two gate driver outputs. EXAMPLE: With a VBIAS of 20V, a VCC limit of 14.6V (max) and the ML4824 driving a total gate charge of 110nC at 100kHz (e.g., 1 IRF840 MOSFET and 2 IRF830 MOSFETs), the gate driver current required is: I GATEDRIVE = 100kHz x 100nC = 11mA (7) 20V - 14.6V R BIAS = --------------------------------------- = 180 19mA + 11mA (8) To check the maximum dissipation in the ML4824, find the current at the minimum VCC (12.4V):: 20V - 12.4V I CC = --------------------------------- = 42.2mA 180 (9) The maximum allowable ICC is 55mA, so this is an acceptable design. The ML4824 should be locally bypassed with a 10nF and a 1F ceramic capacitor. In most applications, an electrolytic capacitor of between 100F and 330F is also required across the part, both for filtering and as part of the start-up bootstrap circuitry. VBIAS RBIAS Solving for the minimum value of CSS: 50A C SS = 5ms x ---------------- = 200nF 1.25V VCC ML4824 10nF CERAMIC 1F CERAMIC GND Caution should be exercised when using this minimum soft start capacitance value because premature charging of the SS capacitor and activation of the PWM section can result if VFB is in the hysteresis band of the VIN OK comparator at start-up. The magnitude of VFB at start-up is related both to line voltage and nominal PFC output voltage. Typically, a 1.0F soft start capacitor will allow time for VFB and PFC out to reach their nominal values prior to activation of the PWM section at line voltages between 90Vrms and 265Vrms. GENERATING VCC The ML4824 is a current-fed part. It has an internal shunt voltage regulator, which is designed to regulate the voltage internal to the part at 13.5V. This allows a low power dissipation while at the same time delivering 10V of gate drive at the PWM OUT and PFC OUT outputs. It is important to 10 Figure 3. External Component Connections to VCC Leading/Trailing Modulation Conventional Pulse Width Modulation (PWM) techniques employ trailing edge modulation in which the switch will turn on right after the trailing edge of the system clock. The error amplifier output voltage is then compared with the modulating ramp. When the modulating ramp reaches the level of the error amplifier output voltage, the switch will be turned OFF. When the switch is ON, the inductor current will ramp up. The effective duty cycle of the trailing edge modulation is determined during the ON time of the switch. Figure 4 shows a typical trailing edge control scheme. REV. 1.0.6 11/7/03 PRODUCT SPECIFICATION ML4824 In the case of leading edge modulation, the switch is turned OFF right at the leading edge of the system clock. When the modulating ramp reaches the level of the error amplifier output voltage, the switch will be turned ON. The effective duty-cycle of the leading edge modulation is determined during the OFF time of the switch. Figure 5 shows a leading edge control scheme. SW2 L1 I2 I1 + One of the advantages of this control teccnique is that it requires only one system clock. Switch 1 (SW1) turns off and switch 2 (SW2) turns on at the same instant to minimize the momentary "no-load" period, thus lowering ripple voltage generated by the switching action. With such synchronized switching, the ripple voltage of the first stage is reduced. Calculation and evaluation have shown that the 120Hz component of the PFC's output ripple voltage can be reduced by as much as 30% using this method. I3 I4 VIN RL SW1 DC C1 RAMP VEAO REF U3 + EA - TIME DFF RAMP OSC + - R Q D U2 Q CLK U1 CLK U4 VSW1 TIME Figure 4. Typical Trailing Edge Control Scheme. SW2 L1 I2 I1 + I3 I4 VIN RL SW1 DC C1 RAMP VEAO REF U3 + -EA VEAO RAMP OSC U4 CLK + - CMP U1 TIME DFF R Q D U2 Q CLK VSW1 TIME Figure 5. Typical Leading Edge Control Scheme. REV. 1.0.6 11/7/03 11 ML4824 PRODUCT SPECIFICATION TYPICAL APPLICATIONS Figure 6 is the application circuit for a complete 100W power factor corrected power supply, designed using the methods and general topology detailed in Application Note 33. AC INPUT 85 TO 265VAC F1 3.15A C1 470nF L1 3.1mH D1 8A, 600V Q1 IRF840 C4 10nF R2A 357k Q2 R17 IRF830 33 C5 100F C25 100nF T1 BR1 4A, 600V R1A 499k R21 22 R2B 357k D13 1A, 50V C2 470nF L2 D11 MBR2545CT 33H D6 600V R1B 499k C30 330F C21 1800F RTN R24 1.2k D3 50V C12 10F R14 33 C22 4.7F Q3 IRF830 R23 1.5k R7A 178k C7 220pF R4 13k 2 3 4 5 C19 1F 6 7 8 VEAO IEAO VFB IAC VREF ISENSE VCC VRMS PFC OUT SS PWM OUT VDC RAMP 1 GND RAMP 2 DC ILIMIT R6 41.2k R18 220 R26 10k R22 8.66k C23 100nF R25 2.26k MOC 8102 R7B 178k TL431 16 15 14 13 C15 10nF 12 C16 1F C13 100nF C14 1F R8 2.37k C31 1nF R11 750k C9 8.2nF C8 82nF 11 10 D8 1A, 20V 9 ML4824 C18 470pF R20 1.1 R19 220 C6 1nF R12 27k 12VDC C24 1F C20 1F R3 75k 1 R5 300m 1W T2 R15 3 R28 180 D12 1A, 50V D7 15V R30 4.7k R27 39k C3 470nF D5 600V R10 6.2k C17 220pF D10 1A, 20V L1: L2: T1: T2: Premier Magnetics #TSD-734 33H, 10A DC Premier Magnetics #TSD-736 Premier Magnetics #TSD-735 Premier Magnetics: (714) 362-4211 C11 10nF Figure 6. 100W Power Factor Corrected Power Supply, Designed Using Micro Linear Application Note 33. 12 REV. 1.0.6 11/7/03 PRODUCT SPECIFICATION ML4824 Mechanical Dimensions inches (millimeters) Package: P16 16-Pin PDIP 0.740 - 0.760 (18.79 - 19.31) 16 0.240 - 0.260 0.295 - 0.325 (6.09 - 6.61) (7.49 - 8.26) PIN 1 ID 0.02 MIN (0.50 MIN) (4 PLACES) 1 0.055 - 0.065 (1.40 - 1.65) 0.015 MIN (0.38 MIN) 0.170 MAX (4.32 MAX) 0.125 MIN (3.18 MIN) REV. 1.0.6 11/7/03 0.100 BSC (2.54 BSC) 0.016 - 0.022 (0.40 - 0.56) SEATING PLANE 0 - 15 0.008 - 0.012 (0.20 - 0.31) 13 ML4824 PRODUCT SPECIFICATION Mechanical Dimensions inches (millimeters) Package: S16W 16-Pin Wide SOIC 0.400 - 0.414 (10.16 - 10.52) 16 0.291 - 0.301 0.398 - 0.412 (7.39 - 7.65) (10.11 - 10.47) PIN 1 ID 1 0.024 - 0.034 (0.61 - 0.86) (4 PLACES) 0.050 BSC (1.27 BSC) 0.095 - 0.107 (2.41 - 2.72) 0 - 8 0.090 - 0.094 (2.28 - 2.39) 14 0.012 - 0.020 (0.30 - 0.51) SEATING PLANE 0.005 - 0.013 (0.13 - 0.33) 0.022 - 0.042 (0.56 - 1.07) 0.009 - 0.013 (0.22 - 0.33) REV. 1.0.6 11/7/03 ML4824 PRODUCT SPECIFICATION Ordering Information Part Number PWM Frequency Temperature Range Package ML4824CP1 1 x PFC 0C to 70C 16-Pin PDIP (P16) ML4824CP2 2 x PFC 0C to 70C 16-Pin PDIP (P16) ML4824CS1 1 x PFC 0C to 70C 16-Pin Wide SOIC (S16W) ML4824CS2 2 x PFC 0C to 70C 16-Pin Wide SOIC (S16W) ML4824IP1 1 x PFC -40C to 85C 16-Pin PDIP (P16) ML4824IS1 1 x PFC -40C to 85C 16-Pin Wide SOIC (S16W) ML4824IS2 2 x PFC -40C to 85C 16-Pin Wide SOIC (S16W) DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 11/7/03 0.0m 003 Stock#DS30004824 (c) 2003 Fairchild Semiconductor Corporation