Intel(R) Wireless Flash Memory (W18) 28F320W18, 28F640W18, 28F128W18 Datasheet Product Features High Performance Read-While-Write/ Erase -- Burst frequency at 66 MHz (zero wait states) -- 60 ns Initial access read speed -- 11 ns Burst mode read speed -- 20 ns Page mode read speed -- 4-, 8-, 16-, and Continuous-Word Burst mode reads -- Burst and Page mode reads in all Blocks, across all partition boundaries -- Burst Suspend feature -- Enhanced Factory Programming at 3.1 s/word Security -- 128-bit OTP Protection Register: 64 unique pre-programmed bits + 64 user-programmable bits -- Absolute Write Protection with VPP at ground -- Individual and Instantaneous Block Locking/Unlocking with Lock-Down Capability Quality and Reliability -- Temperature Range: -40 C to +85 C -- 100K Erase Cycles per Block -- 90 nm ETOXTM IX Process -- 130 nm ETOXTM VIII Process -- 180 nm ETOXTM VII Process Architecture -- Multiple 4-Mbit partitions -- Dual Operation: RWW or RWE -- Parameter block size = 4-Kword -- Main block size = 32-Kword -- Top or bottom parameter devices -- 16-bit wide data bus Software -- 5 s (typ.) Program and Erase Suspend latency time -- Flash Data Integrator (FDI) and Common Flash Interface (CFI) Compatible -- Programmable WAIT signal polarity Packaging and Power -- 90 nm: 32- and 64-Mbit in VF BGA -- 130 nm: 32-, 64-, and 128-Mbit in VF BGA; 128-Mbit in QUAD+ package -- 180 nm: 32- and 128-Mbit densities in VF BGA -- 56 Active Ball Matrix, 0.75 mm BallPitch -- VCC = 1.70 V to 1.95 V -- VCCQ (90 nm) = 1.70 V to 1.95 V -- VCCQ (130 nm) = 1.70 V to 2.24 V or 1.35 V to 1.80 V -- VCCQ (180 nm) = 1.70 V to 2.24 V -- Standby current (130 nm): 8 A (typ.) -- Read current: 8 mA (4-word burst, typ.) The Intel(R) Wireless Flash Memory (W18) device with flexible multi-partition dual-operation architecture, provides high-performance Asynchronous and Synchronous Burst reads. It is an ideal memory for low-voltage burst CPUs. Combining high read performance with flash memory intrinsic non-volatility, the W18 device eliminates the traditional system-performance paradigm of shadowing redundant code memory from slow nonvolatile storage to faster execution memory. It reduces total memory requirement that increases reliability and reduces overall system power consumption and cost. The W18 device's flexible multi-partition architecture allows program or erase to occur in one partition while reading from another partition. This allows for higher data write throughput compared to single-partition architectures and designers can choose code and data partition sizes. The dual-operation architecture allows two processors to interleave code operations while program and erase operations take place in the background. Notice: This document contains information on new products in production. The specifications are subject to change without notice. Verify with your local Intel sales office that you have the latest datasheet before finalizing a design. 290701-013 August 2004 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL(R) PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. The Intel(R) WirelessFlash Memory may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800548-4725 or by visiting Intel's website at http://www.intel.com. Copyright (c) 2004, Intel Corporation. *Other names and brands may be claimed as the property of others. 2 Preliminary Datasheet Contents Contents 1.0 Introduction ...............................................................................................................................9 1.1 1.2 Nomenclature .......................................................................................................................9 Conventions..........................................................................................................................9 2.0 Functional Overview ............................................................................................................11 2.1 Memory Map and Partitioning .............................................................................................12 3.0 Package Information ............................................................................................................15 3.1 3.2 W18 - 180 nm Lithography .................................................................................................15 W18 - 130 nm Lithography .................................................................................................18 4.0 Ballout and Signal Descriptions......................................................................................21 4.1 4.2 Signal Ballout......................................................................................................................21 Signal Descriptions .............................................................................................................23 5.0 Maximum Ratings and Operating Conditions ...........................................................26 5.1 5.2 Absolute Maximum Ratings ................................................................................................26 Operating Conditions ..........................................................................................................27 6.0 Electrical Specifications .....................................................................................................28 6.1 6.2 DC Current Characteristics .................................................................................................28 DC Voltage Characteristics.................................................................................................30 7.0 AC Characteristics ................................................................................................................31 7.1 7.2 7.3 7.4 7.5 7.6 7.7 Read Operations - 90 nm and 130 nm Lithography ...........................................................31 Read Operations - 180 nm Lithography.............................................................................33 AC Write Characteristics.....................................................................................................43 Erase and Program Times..................................................................................................49 Reset Specifications ...........................................................................................................50 AC I/O Test Conditions .......................................................................................................51 Device Capacitance............................................................................................................52 8.0 Power and Reset Specifications .....................................................................................52 8.1 8.2 8.3 8.4 8.5 Active Power.......................................................................................................................52 Automatic Power Savings (APS) ........................................................................................52 Standby Power ...................................................................................................................52 Power-Up/Down Characteristics.........................................................................................53 8.4.1 System Reset and RST# .......................................................................................53 8.4.2 VCC, VPP, and RST# Transitions .........................................................................53 Power Supply Decoupling...................................................................................................53 9.0 Bus Operations Overview ..................................................................................................54 9.1 Bus Operations ...................................................................................................................54 9.1.1 Reads ....................................................................................................................54 9.1.2 Writes.....................................................................................................................55 9.1.3 Output Disable .......................................................................................................55 9.1.4 Burst Suspend .......................................................................................................55 Preliminary Datasheet 3 Contents 9.2 9.3 9.1.5 Standby.................................................................................................................. 56 9.1.6 Reset ..................................................................................................................... 56 Device Commands ............................................................................................................. 56 Command Sequencing ....................................................................................................... 60 10.0 Read Operations .................................................................................................................... 61 10.1 10.2 10.3 10.4 10.5 10.6 10.7 Asynchronous Page Read Mode ........................................................................................ 61 Synchronous Burst Read Mode.......................................................................................... 61 Read Array.......................................................................................................................... 62 Read Identifier .................................................................................................................... 62 CFI Query ........................................................................................................................... 63 Read Status Register.......................................................................................................... 63 Clear Status Register.......................................................................................................... 65 11.0 Program Operations ............................................................................................................. 65 11.1 11.2 11.3 Word Program .................................................................................................................... 65 Factory Programming ......................................................................................................... 66 Enhanced Factory Program (EFP) ..................................................................................... 67 11.3.1 EFP Requirements and Considerations ................................................................ 67 11.3.2 Setup ..................................................................................................................... 68 11.3.3 Program ................................................................................................................. 68 11.3.4 Verify...................................................................................................................... 68 11.3.5 Exit......................................................................................................................... 69 12.0 Program and Erase Operations ....................................................................................... 71 12.1 12.2 12.3 Program/Erase Suspend and Resume ............................................................................... 71 Block Erase......................................................................................................................... 73 Read-While-Write and Read-While-Erase .......................................................................... 75 13.0 Security Modes....................................................................................................................... 76 13.1 13.2 13.3 Block Lock Operations........................................................................................................ 76 13.1.1 Lock ....................................................................................................................... 77 13.1.2 Unlock.................................................................................................................... 77 13.1.3 Lock-Down............................................................................................................. 77 13.1.4 Block Lock Status .................................................................................................. 78 13.1.5 Lock During Erase Suspend .................................................................................. 78 13.1.6 Status Register Error Checking ............................................................................. 78 13.1.7 WP# Lock-Down Control ....................................................................................... 79 Protection Register ............................................................................................................. 79 13.2.1 Reading the Protection Register............................................................................ 80 13.2.2 Programing the Protection Register....................................................................... 80 13.2.3 Locking the Protection Register............................................................................. 81 VPP Protection ................................................................................................................... 82 14.0 Set Read Configuration Register .................................................................................... 83 14.1 14.2 14.3 14.4 14.5 4 Read Mode (RCR[15]) ........................................................................................................ 85 First Access Latency Count (RCR[13:11]).......................................................................... 85 14.2.1 Latency Count Settings.......................................................................................... 86 WAIT Signal Polarity (RCR[10]).......................................................................................... 87 WAIT Signal Function ......................................................................................................... 87 Data Hold (RCR[9])............................................................................................................. 88 Preliminary Datasheet Contents 14.6 14.7 14.8 14.9 14.10 WAIT Delay (RCR[8]) .........................................................................................................89 Burst Sequence (RCR[7]) ...................................................................................................89 Clock Edge (RCR[6]) ..........................................................................................................90 Burst Wrap (RCR[3])...........................................................................................................91 Burst Length (RCR[2:0]) .....................................................................................................91 Appendix A Write State Machine States ...............................................................................92 Appendix B Common Flash Interface (CFI) .........................................................................95 Appendix C Ordering Information .........................................................................................106 Preliminary Datasheet 5 Contents Revision History Date of Revision Version 09/13/00 -001 Description Initial Release Deleted 16-Mbit density Revised ADV#, Section 2.2 Revised Protection Registers, Section 4.16 Revised Program Protection Register, Section 4.18 Revised Example in First Access Latency Count, Section 5.0.2 Revised Figure 5, Data Output with LC Setting at Code 3 Added WAIT Signal Function, Section 5.0.3 Revised WAIT Signal Polarity, Section 5.0.4 Revised Data Output Configuration, Section 5.0.5 Added Figure 7, Data Output Configuration with WAIT Signal Delay Revised WAIT Delay Configuration, Section 5.0.6 Changed VCCQ Spec from 1.7 V - 1.95 V to 1.7 V - 2.24 V in Section 8.2, Extended Temperature Operation 01/29/01 -002 Changed ICCS Spec from 15 A to 18 A in Section 8.4, DC Characteristics Changed ICCR Spec from 10 mA (CLK = 40 MHz, burst length = 4) and 13 mA (CLK = 52 MHz, burst length = 4) to 13 mA, and 16 mA respectively in Section 8.4, DC Characteristics Changed ICCWS Spec from 15 A to 18 A in Section 8.4, DC Characteristics Changed ICCES Spec from 15 A to 18 A in Section 8.4, DC Characteristics Changed tCHQX Spec from 5 ns to 3 ns in Section 8.6, AC Read Characteristics Added Figure 25, WAIT Signal in Synchronous Non-Read Array Operation Waveform Added Figure 26, WAIT Signal in Asynchronous Page Mode Read Operation Waveform Added Figure 27, WAIT Signal in Asynchronous Single Word Read Operation Waveform Revised Appendix E, Ordering Information Revised entire Section 4.10, Enhanced Factory Program Command (EFP) and Figure 6, Enhanced Factory Program Flowchart Revised Section 4.13, Protection Register Revised Section 4.15, Program Protection Register Revised Section 7.3, Capacitance, to include 128-Mbit specs 06/12/01 -003 Revised Section 7.4, DC Characteristics, to include 128-Mbit specs Revised Section 7.6, AC Read Characteristics, to include 128-Mbit device specifications Added tVHGL Spec in Section 7.6, AC Read Characteristics Revised Section 7.7, AC Write Characteristics, to include 128-Mbit device specifications Minor text edits 6 Preliminary Datasheet Contents Date of Revision Version Description New Sections Organization Added 16-Word Burst Feature Added Burst Suspend Section Revised Block Locking State Diagram Revised Active Power Section Revised Automatic Power Savings Section Revised Power-Up/Down Operation Section Revised Extended Temperature Operation 04/05/02 -004 Added 128 Mb DC Characteristics Table Added 128 Mb AC Read Characteristics Revised Table 17. Test Configuration Component Values for Worst Case Speed Conditions Added 0.13 m Product DC and AC Read Characteristics Revised AC Write Characteristics Added Read to Write and Write to Read Transition Waveforms Revised Reset Specifications Various text edits Various text edits 10/10/02 -005 11/12/02 -006 01/14/03 -007 Updated Latency Count Section, including adding Latency Count Tables Added section 8.4 WAIT Function and WAIT Summary Table Updated Package Drawing and Dimensions Various text clarifications Removed Intel Burst Order Revised Table 10 "DC Current Characteristics" Various text edits Revised Table 22, Read Operations, tAPA 03/21/03 -008 Added note to table 15, Configuration Register Descriptions Added note to section 3.1.1, Read Updated Block-Lock Operations (Section 7.1 and Figure 11) Updated Table 21 (128 Mb ICCR) 12/17/03 -009 Updated Table 4 (WAIT behavior) Added QUAD+ ballout, package mechanicals, and order information Various text edits including latest product-naming convention Added 90 nm product line 02/12/04 -010 Removed BGA* package Added Page- and Burst-Mode descriptions Minor text edits Fixed omitted text for Table 21, note 1 regarding max DC voltage on I/O pins 05/06/04 -011 Removed Extended I/O Supply Voltage for 90 nm products Minor text edits 06/03/04 -012 Updated the title and layout of the datasheet VCCQ Max. changed for 90 nm products 06/29/04 -013 Updated "Absolute Maximum Ratings" table Typical ICCS upated as 35 A Updated subtitle Preliminary Datasheet 7 Contents 8 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 1.0 Introduction 1.0 Introduction This datasheet contains information about the Intel(R) Wireless Flash Memory (W18) device family. This section describes nomenclature used in the datasheet. Section 2.0 provides an overview of the W18 flash memory device. Section 6.0, Section 7.0, and Section 8.0 describe the electrical specifications for extended temperature product offerings. Ordering information can be found in Appendix C. 1.1 Nomenclature Acronyms that describe product features or usage are defined here: APS Automatic Power Savings BBA Block Base Address CFI Common Flash Interface CUI Command User Interface DU Don't Use EFP Enhanced Factory Programming FDI Flash Data Integrator NC No Connect OTP One-Time Programmable PBA Partition Base Address RCR Read Configuration Register RWE Read-While-Erase RWW Read-While-Write SCSP Stacked Chip Scale Package SRD Status Register Data VF BGA Very-thi, Fine-pitch, Ball Grid Array WSM Write State Machine 1.2 Conventions The following list describes abbreviated terms and phrases used throughout this document: "1.8 V" Refers to the full VCC voltage range of 1.7 V - 1.95 V (except where noted) and "VPP = 12 V" refers to 12 V 5%. Set Refers to registers means the bit is a logical 1 and cleared means the bit is a logical 0. Pin and signal Often used interchangeably to refer to the external signal connections on the package (ball is the term used for VF BGA). Preliminary Datasheet 9 Intel(R) Wireless Flash Memory (W18) 1.0 Introduction Word 2 bytes or 16 bits. Signal Names are in all CAPS (see Section 4.2, "Signal Descriptions" on page 22.) Voltage Applied to the signal is subscripted for example VPP. Throughout this document, references are made to top, bottom, parameter, and partition. To clarify these references, the following conventions have been adopted: Block A group of bits (or words) that erase simultaneously with one block erase instruction. Main block Contains 32-Kwords. Parameter block Contains 4-Kwords. Block Base Address (BBA) The first address of a block. Partition A group of blocks that share erase and program circuitry and a common Status Register. Partition Base Address (PBA) The first address of a partition. For example, on a 32-Mbit top-parameter device partition number 5 has a PBA of 0x140000. Top partition Located at the highest physical device address. This partition may be a main partition or a parameter partition. Bottom partition Located at the lowest physical device address. This partition may be a main partition or a parameter partition. Main partition Contains only main blocks. Parameter partition Contains a mixture of main blocks and parameter blocks. Top parameter device (TPD) Has the parameter partition at the top of the memory map with the parameter blocks at the top of that partition. This was formerly referred to as a Top-Boot device. Bottom parameter device (BPD) Has the parameter partition at the bottom of the memory map with the parameter blocks at the bottom of that partition. This was formerly referred to as a Bottom-Boot Block flash device. 10 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 2.0 Functional Overview 2.0 Functional Overview This section provides an overview of the W18 device features and architecture. The W18 device provides Read-While-Write (RWW) and Read-White-Erase (RWE) capability with high-performance synchronous and asynchronous reads on package-compatible densities with a 16-bit data bus. Individually-erasable memory blocks are optimally sized for code and data storage. Eight 4-Kword parameter blocks are located in the parameter partition at either the top or bottom of the memory map. The rest of the memory array is grouped into 32-Kword main blocks. The memory architecture for the W18 device consists of multiple 4-Mbit partitions, the exact number depending on device density. By dividing the memory array into partitions, program or erase operations can take place simultaneously during read operations. Burst reads can traverse partition boundaries, but user application code is responsible for ensuring that they don't extend into a partition that is actively programming or erasing. Although each partition has burst-read, write, and erase capabilities, simultaneous operation is limited to write or erase in one partition while other partitions are in a read mode. Augmented erase-suspend functionality further enhances the RWW capabilities of this device. An erase can be suspended to perform a program or read operation within any block, except that which is erase-suspended. A program operation nested within a suspended erase can subsequently be suspended to read yet another memory location. After device power-up or reset, the W18 device defaults to asynchronous page-mode read configuration. Writing to the device's Read Configuration Register (RCR) enables synchronous burst-mode read operation. In synchronous mode, the CLK input increments an internal burst address generator. CLK also synchronizes the flash memory with the host CPU and outputs data on every, or on every other, valid CLK cycle after an initial latency. A programmable WAIT output signals to the CPU when data from the flash memory device is ready. In addition to its improved architecture and interface, the W18 device incorporates Enhanced Factory Programming (EFP), a feature that enables fast programming and low-power designs. The EFP feature provides the fastest currently-available program performance, which can increase a factory's manufacturing throughput. The device supports read operations at 1.8 V and erase and program operations at 1.8 V or 12 V. With the 1.8 V option, VCC and VPP can be tied together for a simple, ultra-low-power design. In addition to voltage flexibility, the dedicated VPP input provides complete data protection when VPP VPPLK. This device (130 nm) allows I/O operation at voltages lower than the minimum VCCQ of 1.7 V. This Extended VCCQ range, 1.35 V - 1.8 V, permits even greater system design flexibility. A 128-bit protection register enhances the user's ability to implement new security techniques and data protection schemes. Unique flash device identification and fraud-, cloning-, or contentprotection schemes are possible through a combination of factory-programmed and user-OTP data cells. Zero-latency locking/unlocking on any memory block provides instant and complete protection for critical system code and data. An additional block lock-down capability provides hardware protection where software commands alone cannot change the block's protection status. Preliminary Datasheet 11 Intel(R) Wireless Flash Memory (W18) 2.0 Functional Overview The Command User Interface (CUI) is the system processor's link to internal flash memory operation. A valid command sequence written to the CUI initiates device Write State Machine (WSM) operation that automatically executes the algorithms, timings, and verifications necessary to manage flash memory program and erase. An internal Status Register provides ready/busy indication results of the operation (success, fail, and so on). Three power-saving features- Automatic Power Savings (APS), standby, and RST# - can significantly reduce power consumption. The device automatically enters APS mode following read cycle completion. Standby mode begins when the system deselects the flash memory by de-asserting CE#. Driving RST# low produces power savings similar to standby mode. It also resets the part to read-array mode (important for system-level reset), clears internal Status Registers, and provides an additional level of flash write protection. 2.1 Memory Map and Partitioning The W18 device is divided into 4-Mbit physical partitions, which allows simultaneous RWW or RWE operations and allows users to segment code and data areas on 4-Mbit boundaries. The device's memory array is asymmetrically blocked, which enables system code and data integration within a single flash device. Each block can be erased independently in block erase mode. Simultaneous program and erase operations are not allowed; only one partition at a time can be actively programming or erasing. See Table 1, "Bottom Parameter Memory Map" on page 13 and Table 2, "Top Parameter Memory Map" on page 14. The 32-Mbit device has eight partitions, the 64-Mbit device has 16 partitions, and the 128-Mbit device has 32 partitions. Each device density contains one parameter partition and several main partitions. The 4-Mbit parameter partition contains eight 4-Kword parameter blocks and seven 32Kword main blocks. Each 4-Mbit main partition contains eight 32-Kword blocks each. The bulk of the array is divided into main blocks that can store code or data, and parameter blocks that allow storage of frequently updated small parameters that are normally stored in EEPROM. By using software techniques, the word-rewrite functionality of EEPROMs can be emulated. . 12 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 2.0 Functional Overview Table 1. Bottom Parameter Memory Map 64-Mbit Blk # 128-Mbit 32 262 7F8000-7FFFFF .. . Blk # .. . 32-Mbit .. . Blk # 32 135 400000-407FFF 3F8000-3FFFFF 134 3F8000-3FFFFF .. . .. . .. . .. . 134 .. . 32 32 71 200000-207FFF 71 200000-207FFF 1F8000-1FFFFF 70 1F8000-1FFFFF 70 1F8000-1FFFFF .. . 100000-107FFF 32 38 0F8000-0FFFFF 38 0F8000-0FFFFF 38 0F8000-0FFFFF 0C0000-0C7FFF 32 30 0B8000-0BFFFF 30 0B8000-0BFFFF 30 0B8000-0BFFFF 32 22 078000-07FFFF 22 078000-07FFFF 22 078000-07FFFF 038000-03FFFF 14 038000-03FFFF .. . 14 32 8 008000-00FFFF 8 008000-00FFFF 8 008000-00FFFF 4 7 007000-007FFF 7 007000-007FFF 7 007000-007FFF .. . 038000-03FFFF .. . 14 .. . 32 .. . 040000-047FFF .. . 15 .. . 040000-047FFF .. . 15 .. . 040000-047FFF .. . 15 .. . 32 .. . .. . 080000-087FFF .. . 23 .. . 080000-087FFF .. . 23 .. . 080000-087FFF .. . 23 .. . 32 .. . .. . 31 .. . 0C0000-0C7FFF .. . 31 .. . 0C0000-0C7FFF .. . 31 .. . 32 .. . .. . .. . 39 .. . .. . 100000-107FFF .. . .. . 39 .. . .. . 100000-107FFF .. . 39 .. . 32 .. . .. . 70 .. . 32 .. . Four Partitions One Partition One Partition Parameter Partition One Partition One Partition Main Partitions Eight Partitions Sixteen Partitions Size (KW) 4 0 000000-000FFF 0 000000-000FFF 0 000000-000FFF Preliminary Datasheet 13 Intel(R) Wireless Flash Memory (W18) 2.0 Functional Overview 14 Top Parameter Memory Map 4 70 1FF000-1FFFFF 134 3FF000-3FFFFF 262 7FF000-7FFFFF 7F8000-7F8FFF 254 7F0000-7F7FFF 7C0000-7C7FFF 32 55 1B8000-1BFFFF 119 3B8000-3BFFFF 247 7B8000-7BFFFF 780000-787FFF 32 47 178000-17FFFF 111 378000-37FFFF 239 778000-77FFFF 39 138000-13FFFF 103 338000-33FFFF 231 738000-73FFFF 700000-707FFF 32 31 0F8000-0FFFFF 95 2F8000-2FFFFF 223 6F8000-6FFFFF 32 0 600000-607FFF 32 63 1F8000-1FFFFF 191 5F8000-5FFFFF 32 0 .. . 192 000000-007FFF 128 400000-407FFF 32 127 3F8000-3FFFFF .. . 200000-207FFF .. . 64 .. . 000000-007FFF .. . .. . 224 .. . 300000-307FFF .. . 96 .. . 100000-107FFF .. . 32 .. . 32 .. . .. . 32 .. . 740000-747FFF .. . 232 .. . 340000-347FFF .. . 104 .. . 140000-147FFF .. . 40 .. . 32 .. . .. . 240 .. . 380000-387FFF .. . 112 .. . 18000-187FFF .. . 48 .. . 32 .. . .. . 248 .. . 3C0000-3C7FFF .. . 120 .. . 1C0000-1C7FFF .. . 56 .. . 32 .. . .. . 255 3F0000-3F7FFF .. . 3F8000-3F8FFF 126 .. . 127 1F0000-1F7FFF .. . 1F8000-1F8FFF 62 .. . 63 .. . 4 32 .. . .. . 128-Mbit .. . Blk # .. . 64-Mbit .. . Blk # .. . 32-Mbit .. . Blk # .. . Size (KW) .. . One Partition One Partition Four Partitions Sixteen Partitions Eight Partitions Main Partitions One Partition One Partition Parameter Partition Table 2. 32 0 000000-007FFF Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 3.0 Package Information 3.0 Package Information 3.1 W18 - 90 nm Lithography Figure 1. 32- and 64-Mbit VF BGA Package Drawing Ball A1 Corner Ball A1 Corner S1 D 1 E 2 3 4 5 6 7 8 8 A A B B C C D D E E F F G G 7 6 5 4 3 2 S2 1 e b Top View - Bump Side Down Bottom View - Ball Side Up A1 A2 A Seating Y Plane Table 3. 32- and 64-Mbit VF BGA Package Dimensions Millimeters Dimension Inches Symbol Min Nom Max Min Nom Max Package Height A - - 1.000 - - 0.0394 Ball Height A1 0.150 - - 0.0059 - - Package Body Thickness A2 - 0.665 - - 0.0262 - Ball (Lead) Width b 0.325 0.375 0.425 0.0128 0.0148 0.0167 Package Body Width D 7.600 7.700 7.800 0.2992 0.3031 0.3071 Package Body Length E 8.900 9.000 9.100 0.3504 0.3543 0.3583 Pitch [e] - 0.750 - - 0.0295 - Ball (Lead) Count N - 56 - - 56 - Seating Plane Coplanarity Y - - 0.100 - - 0.0039 Corner to Ball A1 Distance Along D S1 1.125 1.225 1.325 0.0443 0.0482 0.0522 Corner to Ball A1 Distance Along E S2 2.150 2.250 2.350 0.0846 0.0886 0.0925 Preliminary Datasheet 15 Intel(R) Wireless Flash Memory (W18) 3.0 Package Information 3.2 W18 - 130 nm Lithography Figure 2. 32-, 64-, and 128-Mbit VF BGA Package Drawing Ball A1 Corner Ball A1 Corner S1 D 1 E 2 3 4 5 6 7 8 8 A A B B C C D D E E F F G G 7 6 5 4 3 2 S2 1 e b Top View - Bump Side Down Bottom View - Ball Side Up A1 A2 A Seating Y Plane Table 4. 32-, 64-, and 128-Mbit VF BGA Package Dimensions Millimeters Dimension Inches Symbol Min Nom Max Min Nom Max Package Height A - - 1.000 - - 0.0394 Ball Height A1 0.150 - - 0.0059 - - Package Body Thickness A2 - 0.665 - - 0.0262 - Ball (Lead) Width b 0.325 0.375 0.425 0.0128 0.0148 0.0167 Package Body Width (32/64-Mbit) D 7.600 7.700 7.800 0.2992 0.3031 0.3071 Package Body Width (128-Mbit) D 10.900 11.000 11.100 0.4291 0.4331 0.4370 Package Body Length (32/64/128-Mbit) E 8.900 9.000 9.100 0.3504 0.3543 0.3583 Pitch [e] - 0.750 - - 0.0295 - Ball (Lead) Count N - 56 - - 56 - Seating Plane Coplanarity Y - - 0.100 - - 0.0039 Corner to Ball A1 Distance Along D (32/64-Mbit) S1 1.125 1.225 1.325 0.0443 0.0482 0.0522 Corner to Ball A1 Distance Along D (128-Mbit) S1 2.775 2.2875 2.975 0.1093 0.1132 0.1171 Corner to Ball A1 Distance Along E (32/64/128-Mbit) S2 2.150 2.250 2.350 0.0846 0.0886 0.0925 16 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 3.0 Package Information Figure 3. 128-Mbit QUAD+ Package Drawing S1 A1 Index Mark 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 1 S2 A A B B C C D D E E F D F G G H H J J K K L L M M e b E Bottom View - Ball Up Top View - Ball Down A2 A1 A Y Drawing not to scale. Dimensions Package Height Ball Height Package Body Thickness Ball (Lead) Width Package Body Length Package Body Width Pitch Ball (Lead) Count Seating Plane Coplanarity Corner to Ball A1 Distance Along E Corner to Ball A1 Distance Along D Preliminary Datasheet Symbol A A1 A2 b D E e N Y S1 S2 Min Millimeters Nom Max 1.200 0.200 0.325 9.900 7.900 1.100 0.500 Notes Min Inches Nom Max 0.0472 0.0079 0.860 0.375 10.000 8.000 0.800 88 1.200 0.600 0.425 10.100 8.100 0.0128 0.3898 0.3110 0.100 1.300 0.700 0.0433 0.0197 0.0339 0.0148 0.3937 0.3150 0.0315 88 0.0472 0.0236 0.0167 0.3976 0.3189 0.0039 0.0512 0.0276 17 Intel(R) Wireless Flash Memory (W18) 3.0 Package Information 3.3 W18 - 180 nm Lithography Figure 4. 32-Mbit VF BGA Package Drawing Ball A1 Corner Ball A1 Corner S1 D 1 E 2 3 4 5 6 7 8 8 A A B B C C D D E E F F G G 7 6 5 4 3 2 1 S2 e b Top View - Bump Side Down Bottom View - Ball Side Up A1 A2 A Seating Y Plane Side View Note: Drawing not to scale Figure 5. 128-Mbit VF BGA Package Drawing Ball A1 Corner 1 E S1 D 2 3 4 5 6 7 8 9 10 10 A A B B C C D D E E F F G G H H J J 9 8 7 6 5 4 3 Ball A1 Corner S2 2 1 e b Top View - Bump Side Down Bottom View - Ball Side Up A1 A2 A Seating Plane Y Side View Note: Drawing not to scale 18 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 3.0 Package Information Table 5. 32- and 128-Mbit VF BGA Package Dimensions Millimeters Dimension Inches Symbol Min Nom Max Min Nom Max Package Height A 0.850 - 1.000 0.0335 - 0.0394 Ball Height A1 0.150 - - 0.0059 - - Package Body Thickness A2 0.615 0.665 0.715 0.0242 0.0262 0.0281 Ball (Lead) Width b 0.325 0.375 0.425 0.0128 0.0148 0.0167 Package Body Width (32-Mbit) D 7.600 7.700 7.800 0.2992 0.3031 0.3071 Package Body Length (32-Mbit) E 8.900 9.000 9.100 0.3503 0.3543 0.3583 Package Body Width (128-Mbit) D 12.400 12.500 12.600 0.4882 0.4921 0.4961 Package Body Length (128-Mbit) E 11.900 12.000 12.100 0.4685 0.4724 0.4764 Pitch [e] - 0.750 - - 0.0295 - Ball (Lead) Count 32-Mbit N - 56 - - 56 - Ball (Lead) Count 128-Mbit N - 60 - - 60 - Seating Plane Coplanarity Y - - 0.100 - - 0.0039 Corner to Ball A1 Distance Along D (32-Mbit) S1 1.125 1.225 1.325 0.0443 0.0482 0.0522 Corner to Ball A1 Distance Along E (32-Mbit) S2 2.150 2.250 2.350 0.0846 0.0886 0.0925 Corner to Ball A1 Distance Along D (128-Mbit) S1 2.775 2.875 2.975 0.1093 0.1132 0.1171 Corner to Ball A1 Distance Along E (128-Mbit) S2 2.900 3.000 3.1000 0.1142 0.1181 0.1220 Preliminary Datasheet 19 Intel(R) Wireless Flash Memory (W18) 4.0 Ballout and Signal Descriptions 4.0 Ballout and Signal Descriptions 4.1 Signal Ballout The W18 device is available in a 56-ball VF BGA and BGA Chip Scale Package with 0.75 mm ball pitch, or the 88-ball (80 active balls) QUAD+ SCSP package. Figure 6 shows the device ballout for the VF BGA package. Figure 7 shows the device ballout for the QUAD+ package. Figure 6. 1 56-Ball VF BGA Ballout 2 3 4 5 6 7 8 8 7 6 5 4 3 2 1 A A A11 A8 VSS VCC A12 A9 A20 CLK VPP A18 A6 A4 A4 A6 A18 RST# A17 A5 A3 A3 A5 A17 VPP VCC VSS A8 A11 RST# CLK A20 A9 A12 B B C C A13 A10 A21 ADV# WE# A19 A7 A2 A2 A7 A19 WE# ADV# A21 A10 A13 D D A15 A14 WAIT A16 DQ12 WP# A22 A1 A1 A22 WP# DQ12 A16 WAIT A14 A15 VCCQ DQ15 DQ6 DQ4 DQ2 DQ1 CE# A0 A0 CE# DQ1 DQ2 DQ4 DQ6 DQ15 VCCQ E E F F VSS DQ14 DQ13 DQ11 DQ10 DQ9 DQ0 OE# OE# DQ0 DQ9 DQ10 DQ11 DQ13 DQ14 VSS G G DQ7 VSSQ DQ5 VCC DQ3 VCCQ Top View - Ball Side Down Complete Ink Mark Not Shown DQ8 VSSQ VSSQ DQ8 VCCQ DQ3 VCC DQ5 VSSQ DQ7 Bottom View - Ball Side Up Notes: 1. On lower density devices, upper address balls can be treated as NC. (Example: For 32-Mbit density, A21 and A22 are NC). 2. See Appendix , "" on page 15 for mechanical specifications for the package. 20 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 4.0 Ballout and Signal Descriptions Figure 7. 88-Ball (80 Active Balls) QUAD+ Ballout A 1 2 3 4 5 DU DU A4 A18 A19 VSS A5 R-LB# A23 VSS A3 A17 A24 F-VPP, F-VPEN A2 A7 A25 F-WP# A1 A6 A0 D8 D2 D10 R-OE# D0 D1 D9 6 7 8 DU DU A21 A11 A22 A12 R-WE# P1-CS# A9 A13 ADV# A20 A10 A15 R-UB# F-RST# F-WE# A8 A14 A16 D5 D13 WAIT F2-CE# D3 D12 D14 D7 F2-OE# D11 D4 D6 D15 VCCQ B F1-VCC F2-VCC C S-CS2 CLK D E F G H J S-CS1# F1-OE# K F1-CE# P2-CS# F3-CE# S-VCC P-VCC F2-VCC VCCQ P-Mode, P-CRE L M VSS VSS DU DU VCCQ F1-VCC VSS VSS VSS VSS DU DU Top View - Ball Side Down Legend: Global SRAM/PSRAM specific Flash specific Notes: 1. Unused upper address balls can be treated as NC (for 128-Mbit device, A[25:23] are not used). 2. See "Package Information" on page 15 for the mechanical specifications for the package. Preliminary Datasheet 21 Intel(R) Wireless Flash Memory (W18) 4.0 Ballout and Signal Descriptions 4.2 Signal Descriptions Table 6 describes the signals used on the VF BGA package. Table 7 on page 23 describes the signals used on the QUAD+ package. Table 6. Signal Descriptions - VF BGA Package Symbol Type Name and Function A[22:0] Input D[15:0] Input/ Output DATA INPUTS/OUTPUTS: Inputs data and commands during write cycles; outputs data during memory, Status Register, protection register, and configuration code reads. Data pins float when the chip or outputs are deselected. Data is internally latched during writes. ADV# Input ADDRESS VALID: ADV# indicates valid address presence on address inputs. During synchronous read operations, all addresses are latched on ADV#'s rising edge or the next valid CLK edge with ADV# low, whichever occurs first. CE# Input CHIP ENABLE: Asserting CE# activates internal control logic, I/O buffers, decoders, and sense amps. De-asserting CE# deselects the device, places it in standby mode, and places all outputs in High-Z. CLK Input CLOCK: CLK synchronizes the device to the system bus frequency during synchronous reads and increments an internal address generator. During synchronous read operations, addresses are latched on ADV#'s rising edge or the next valid CLK edge with ADV# low, whichever occurs first. OE# Input OUTPUT ENABLE: When asserted, OE# enables the device's output data buffers during a read cycle. When OE# is deasserted, data outputs are placed in a high-impedance state. RST# Input RESET: When low, RST# resets internal automation and inhibits write operations. This provides data protection during power transitions. de-asserting RST# enables normal operation and places the device in asynchronous read-array mode. WAIT Output WAIT: The WAIT signal indicates valid data during synchronous read modes. It can be configured to be asserted-high or asserted-low based on bit 10 of the Read Configuration Register. WAIT is tristated if CE# is deasserted. WAIT is not gated by OE#. WE# Input WRITE ENABLE: WE# controls writes to the CUI and array. Addresses and data are latched on the rising edge of WE#. WP# Input WRITE PROTECT: Disables/enables the lock-down function. When WP# is asserted, the lock-down mechanism is enabled and blocks marked lock-down cannot be unlocked through software. See Section 13.1, "Block Lock Operations" on page 82 for details on block locking. ADDRESS INPUTS: For memory addresses. 32-Mbit: A[20:0]; 64-Mbit: A[21:0]; 128-Mbit: A[22:0] ERASE AND PROGRAM POWER: A valid voltage on this pin allows erasing or programming. Memory contents cannot be altered when VPP VPPLK. Block erase and program at invalid VPP voltages should not be attempted. VPP Power Set VPP = VCC for in-system program and erase operations. To accommodate resistor or diode drops from the system supply, the VIH level of VPP can be as low as VPP1 min. VPP must remain above VPP1 min to perform in-system flash modification. VPP may be 0 V during read operations. VPP2 can be applied to main blocks for 1000 cycles maximum and to parameter blocks for 2500 cycles. VPP can be connected to 12 V for a cumulative total not to exceed 80 hours. Extended use of this pin at 12 V may reduce block cycling capability. 22 VCC Power DEVICE POWER SUPPLY: Writes are inhibited at VCC VLKO. Device operations at invalid VCC voltages should not be attempted. VCCQ Power OUTPUT POWER SUPPLY: Enables all outputs to be driven at VCCQ. This input may be tied directly to VCC. VSS Power GROUND: Pins for all internal device circuitry must be connected to system ground. VSSQ Power OUTPUT GROUND: Provides ground to all outputs which are driven by VCCQ. This signal may be tied directly to VSS. DU -- DO NOT USE: Do not use this pin. This pin should not be connected to any power supplies, signals or other pins and must be floated. NC -- NO CONNECT: No internal connection; can be driven or floated. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 4.0 Ballout and Signal Descriptions Table 7. Symbol Signal Descriptions - QUAD+ Package (Sheet 1 of 3) Type Description ADDRESS INPUTS: Inputs for all die addresses during read and write operations. A[MAX:MIN] Input * * * * * 256-Mbit Die : AMAX= A23 128-Mbit Die : AMAX = A22 64-Mbit Die : AMAX = A21 32-Mbit Die : AMAX = A20 8-Mbit Die : AMAX = A18 A0 is the lowest-order 16-bit wide address. A[25:24] denote high-order addresses reserved for future device densities. D[15:0] Input/ Output DATA INPUTS/OUTPUTS: Inputs data and commands during write cycles, outputs data during read cycles. Data signals float when the device or its outputs are deselected. Data are internally latched during writes on the flash device. FLASH CHIP ENABLE: Low-true input. F[3:1]-CE# Input F[3:1]-CE# low selects the associated flash memory die. When asserted, flash internal control logic, input buffers, decoders, and sense amplifiers are active. When deasserted, the associated flash die is deselected, power is reduced to standby levels, data and WAIT outputs are placed in high-Z state. F1-CE# selects or deselects flash die #1; F2-CE# selects or deselects flash die #2 and is RFU on combinations with only one flash die. F3-CE# selects or deselects flash die #3 and is RFU on stacked combinations with only one or two flash dies. SRAM CHIP SELECT: Low-true / High-true input (S-CS1# / S-CS2 respectively). S-CS1# S-CS2 Input When either/both SRAM Chip Select signals are asserted, SRAM internal control logic, input buffers, decoders, and sense amplifiers are active. When either/both SRAM Chip Select signals are deasserted, the SRAM is deselected and its power is reduced to standby levels. S-CS1# and S-CS2 are available on stacked combinations with SRAM die and are RFU on stacked combinations without SRAM die. PSRAM CHIP SELECT: Low-true input. When asserted, PSRAM internal control logic, input buffers, decoders, and sense amplifiers are active. When deasserted, the PSRAM is deselected and its power is reduced to standby levels. P[2:1]-CS# Input P1-CS# selects PSRAM die #1 and is available only on stacked combinations with PSRAM die. This ball is an RFU on stacked combinations without PSRAM. P2-CS# selects PSRAM die #2 and is available only on stacked combinations with two PSRAM dies. This ball is an RFU on stacked combinations without PSRAM or with a single PSRAM. FLASH OUTPUT ENABLE: Low-true input. F[2:1]-OE# Input Fx-OE# low enables the selected flash's output buffers. F[2:1]-OE# high disables the selected flash's output buffers, placing them in High-Z. F1-OE# controls the outputs of flash die #1; F2-OE# controls the outputs of flash die #2 and flash die #3. F2-OE# is available on stacked combinations with two or three flash die and is RFU on stacked combinations with only one flash die. RAM OUTPUT ENABLE: Low-true input. R-OE# Input R-OE# low enables the selected RAM's output buffers. R-OE# high disables the RAM output buffers, and places the selected RAM outputs in High-Z. R-OE# is available on stacked combinations with PSRAM or SRAM die, and is an RFU on flash-only stacked combinations. FLASH WRITE ENABLE: Low-true input. F-WE# Input F-WE# controls writes to the selected flash die. Address and data are latched on the rising edge of FWE#. RAM WRITE ENABLE: Low-true input. R-WE# Input R-WE# controls writes to the selected RAM die. R-WE# is available on stacked combinations with PSRAM or SRAM die and is an RFU on flash-only stacked combinations. Preliminary Datasheet 23 Intel(R) Wireless Flash Memory (W18) 4.0 Ballout and Signal Descriptions Table 7. Signal Descriptions - QUAD+ Package (Sheet 2 of 3) CLOCK: Synchronizes the flash die with the system bus clock in synchronous read mode and increments the internal address generator. CLK Input During synchronous read operations, addresses are latched on the rising edge of ADV#, or on the next valid CLK edge with ADV# low, whichever occurs first. In asynchronous mode, addresses are latched on the rising edge ADV#, or are continuously flowthrough when ADV# is kept asserted. WAIT: Output signal. WAIT Output Indicates invalid data during synchronous array or non-array flash reads. Read Configuration Register bit 10 (RCR[10]) determines WAIT-asserted polarity (high or low). WAIT is High-Z if F-CE# is deasserted; WAIT is not gated by F-OE#. * In synchronous array or non-array flash read modes, WAIT indicates invalid data when asserted and valid data when deasserted. * In asynchronous flash page read, and all flash write modes, WAIT is asserted. FLASH WRITE PROTECT: Low-true input. F-WP# enables/disables the lock-down protection mechanism of the selected flash die. F-WP# Input * F-WP# low enables the lock-down mechanism where locked down blocks cannot be unlocked with software commands. * F-WP# high disables the lock-down mechanism, allowing locked down blocks to be unlocked with software commands. ADDRESS VALID: Low-true input. ADV# Input During synchronous flash read operations, addresses are latched on the rising edge of ADV#, or on the next valid CLK edge with ADV# low, whichever occurs first. In asynchronous flash read operations, addresses are latched on the rising edge of ADV#, or are continuously flow-through when ADV# is kept asserted. RAM UPPER / LOWER BYTE ENABLES: Low-true input. R-UB# R-LB# Input During RAM read and write cycles, R-UB# low enables the RAM high order bytes on D[15:8], and RLB# low enables the RAM low-order bytes on D[7:0]. R-UB# and R-LB# are available on stacked combinations with PSRAM or SRAM die and are RFU on flash-only stacked combinations. FLASH RESET: Low-true input. F-RST# Input F-RST# low initializes flash internal circuitry and disables flash operations. F-RST# high enables flash operation. Exit from reset places the flash in asynchronous read array mode. P-Mode (PSRAM Mode): Low-true input. P-Mode is used to program the Configuration Register, and enter/exit Low Power Mode of PSRAM die. P-Mode, P-CRE P-Mode is available on stacked combinations with asynchronous-only PSRAM die. Input P-CRE (PSRAM Configuration Register Enable): High-true input. P-CRE is high, write operations load the refresh control register or bus control register. P-CRE is applicable only on combinations with synchronous PSRAM die. P-Mode, P-CRE is an RFU on stacked combinations without PSRAM die. FLASH PROGRAM AND ERASE POWER: Valid F-VPP voltage on this ball enables flash program/ erase operations. F-VPP, F-VPEN Power Flash memory array contents cannot be altered when F-VPP(F-VPEN) < VPPLK (VPENLK). Erase / program operations at invalid F-VPP (F-VPEN) voltages should not be attempted. Refer to flash discrete product datasheet for additional details. F-VPEN (Erase/Program/Block Lock Enables) is not available for L18/L30 SCSP products. F[2:1]-VCC Power FLASH LOGIC POWER: F1-VCC supplies power to the core logic of flash die #1; F2-VCC supplies power to the core logic of flash die #2 and flash die #3. Write operations are inhibited when F-VCC < VLKO. Device operations at invalid F-VCC voltages should not be attempted. F2-VCC is available on stacked combinations with two or three flash dies, and is an RFU on stacked combinations with only one flash die. 24 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 4.0 Ballout and Signal Descriptions Table 7. Signal Descriptions - QUAD+ Package (Sheet 3 of 3) SRAM POWER SUPPLY: Supplies power for SRAM operations. S-VCC Power P-VCC Power P-VCC is available on stacked combinations with PSRAM die, and is RFU on stacked combinations without PSRAM die. VCCQ Power DEVICE I/O POWER: Supply power for the device input and output buffers. VSS Power DEVICE GROUND: Connect to system ground. Do not float any VSS connection. RFU -- RESERVED for FUTURE USE: Reserved for future device functionality/ enhancements. Contact Intel regarding the use of balls designated RFU. DU -- DO NOT USE: Do not connect to any other signal, or power supply; must be left floating. S-VCC is available on stacked combinations with SRAM die, and is RFU on stacked combinations without SRAM die. PSRAM POWER SUPPLY: Supplies power for PSRAM operations. Preliminary Datasheet 25 Intel(R) Wireless Flash Memory (W18) 5.0 Maximum Ratings and Operating Conditions 5.0 Maximum Ratings and Operating Conditions 5.1 Absolute Maximum Ratings Warning: Stressing the device beyond the "Absolute Maximum Ratings" may cause permanent damage. These are stress ratings only. Notice: This datasheet contains information on products in the design phase of development. The information here is subject to change without notice. Do not finalize a design with this information. Table 8. Absolute Maximum Ratings Parameter Maximum Rating Notes Temperature under Bias -40 C to +85 C Storage Temperature -65 C to +125 C Voltage on Any Pin (except VCC, VCCQ, VPP) -0.5 V to +2.45 V 1,2 VPP Voltage -0.2 V to +13.1 V 1,3,4 VCC and VCCQ Voltage -0.2 V to +2.45 V 1,2 Output Short Circuit Current 100 mA 5 Notes: 1. All specified voltages are relative to VSS. 2. During transitions, this level may undershoot to -2.0 V for periods < 20 ns and overshoot to VCCQ +2.0 V for periods < 20 ns. 3. Maximum DC voltage on VPP may overshoot to +14.6 V for periods < 20 ns. 4. VPP program voltage is normally VPP1. VPP can be 12 V 0.6 V for 1000 cycles on the main blocks and 2500 cycles on the parameter blocks during program/erase. 5. Output shorted for no more than one second. No more than one output shorted at a time. 26 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 5.0 Maximum Ratings and Operating Conditions 5.2 Operating Conditions Warning: Operation beyond the "Operating Conditions" is not recommended, and extended exposure beyond the "Operating Conditions" may affect device reliability. Table 9. Extended Temperature Operation Parameter1 Symbol TA Min Nom Max Unit Note Operating Temperature -40 25 85 C VCC Supply Voltage 1.7 1.8 1.95 3 I/O Supply Voltage (90 nm) 1.7 1.8 1.95 3 I/O Supply Voltage (130 nm and 180 nm) 1.7 1.8 2.24 Extended I/O Supply Voltage (130 nm) 1.35 1.5 1.8 4 VPP Voltage Supply (Logic Level) 0.90 1.80 1.95 2 Programming VPP 11.4 12.0 12.6 2 3 V VPP1 tPPH Block Erase Cycles Maximum VPP Hours VPP = 12 V - - 80 Main and Parameter Blocks VPP VCC 100,000 - - Main Blocks VPP = 12 V - - 1000 Parameter Blocks VPP = 12 V - - 2500 Hours 2 2 Cycles 2 2 Notes: 1. See Section 6.1 and Section 6.2, "DC Voltage Characteristics" on page 30 for specific voltage-range specifications. 2. VPP is normally VPP1. VPP can be connected to 11.4 V-12.6 V for 1000 cycles on main blocks at extended temperatures and 2500 cycles on parameter blocks at extended temperatures. 3. Contact your Intel field representative for VCC/VCCQ operations down to 1.65 V. 4. See the tables in Section 5.0, "Maximum Ratings and Operating Conditions" on page 26 and in Section 7.0, "AC Characteristics" on page 31 for operating characteristics within the Extended VCCQ voltage range. Preliminary Datasheet 27 Intel(R) Wireless Flash Memory (W18) 6.0 Electrical Specifications 6.0 Electrical Specifications 6.1 DC Current Characteristics Table 10. DC Current Characteristics (Sheet 1 of 2) VCCQ= 1.35 V - 1.8 V (2) Parameter (1) Symbol 32/64/128Mbit VCCQ= 1.8 V 32/64-Mbit 128-Mbit Unit Test Condition Note Typ Max Typ Max Typ Max - TBD - 1 - 1 A VCC = VCCMax VCCQ = VCCQMax VIN = VCCQ or GND - TBD - 1 - 1 A VCC = VCCMax VCCQ = VCCQMax VIN = VCCQ or GND TBD TBD 5 18 5 25 TBD TBD 8 50 8 70 A 9 90 nm ICCS VCC = VCCMax VCCQ = VCCQMax CE# = VCC RST# =VSSQ - - 35 50 - - 180 nm ICCAPS TBD TBD 5 18 5 25 TBD TBD 8 50 8 70 A 10 - - 35 50 - - VCC = VCCMax VCCQ = VCCQMax CE# = VSSQ RST# =VCCQ All other inputs =VCCQ or VSSQ TBD TBD 3 6 4 7 mA 4 Word Read 3 TBD TBD 6 13 6 13 mA Burst length = 4 TBD TBD 8 14 8 14 mA Burst length = 8 TBD TBD 10 18 11 19 mA Burst length =16 TBD TBD 11 20 11 20 mA Burst length = Continuous TBD TBD 7 16 7 16 mA Burst length = 4 TBD TBD 10 18 10 18 mA Burst length = 8 TBD TBD 12 22 12 22 mA Burst length = 16 TBD TBD 13 25 13 25 mA Burst length = Continuous TBD TBD 8 17 - - mA Burst length = 4 TBD TBD 11 20 - - mA Burst length = 8 TBD TBD 14 25 - - mA Burst length = 16 TBD TBD 16 30 - - mA Burst length = Continuous ILI Input Load ILO Output Leakage D[15:0] 180 nm ICCS 130 nm ICCS 130 nm ICCAPS VCC Standby APS 90 nm ICCAPS Asynchronous Page Mode f=13 MHz ICCR Average VCC Read Synchronous CLK = 40 MHz Synchronous CLK = 54 MHz ICCR 28 Average VCC Read Synchronous CLK = 66 MHz 8 3 3 3, 4 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 6.0 Electrical Specifications Table 10. DC Current Characteristics (Sheet 2 of 2) VCCQ= 1.35 V - 1.8 V (2) Symbol ICCW ICCE Parameter (1) 32/64/128Mbit VCCQ= 1.8 V 32/64-Mbit 128-Mbit Typ Max Typ Max Typ Max TBD TBD 18 40 18 40 Unit Test Condition mA VPP = VPP1, Program in Progress VCC Program Note 4,5,6 TBD TBD 8 15 8 15 mA VPP = VPP2, Program in Progress TBD TBD 18 40 18 40 mA VPP = VPP1, Block Erase in Progress TBD TBD 8 15 8 15 mA VPP = VPP2, Block Erase in Progress VCC Block Erase 4,5,6 ICCWS VCC Program Suspend TBD TBD 5 18 5 25 A CE# = VCC, Program Suspended 7 ICCES VCC Erase Suspend TBD TBD 5 18 5 25 A CE# = VCC, Erase Suspended 7 TBD TBD 0.2 5 0.2 5 A VPP VCC the input load current increases to 10 A max. 9. ICCS is the average current measured over any 5 ms time interval 5 s after a CE# de-assertion. 10. Refer to section Section 8.2, "Automatic Power Savings (APS)" on page 56 for ICCAPS measurement details. 11. TBD values are to be determined pending silicon characterization. Preliminary Datasheet 29 Intel(R) Wireless Flash Memory (W18) 6.0 Electrical Specifications 6.2 DC Voltage Characteristics Table 11. DC Voltage Characteristics VCCQ= 1.35 V - 1.8 V (1) Symbol Parameter 32/64/128-Mbit VCCQ= 1.8 V 32/64-Mbit Min Max Input Low 0 VIH Input High VCCQ - 0.2 VOL Output Low VOH Output High VPPLK VPP Lock-Out VLKO VCC Lock 1.0 - 1.0 - 1.0 - V VILKOQ VCCQ Lock TBD - 0.9 - 0.9 - V VIL Min Max 0.2 0 VCCQ VCCQ - 0.4 - 0.1 VCCQ - 0.1 - Unit 128-Mbit Test Condition Note Min Max 0.4 0 0.4 V 2 VCCQ VCCQ - 0.4 VCCQ V 2 - 0.1 - 0.1 V VCC = VCCMin VCCQ = VCCQMin IOL = 100 A - VCCQ - 0.1 - VCCQ - 0.1 - V VCC = VCCMin VCCQ = VCCQMin IOH = -100 A 0.4 - 0.4 - 0.4 V 3 Notes: 1. VCCQ = 1.35 V - 1.8V is available on 130 nm devices only. 2. VIL can undershoot to -1.0 V for durations of 2 ns or less and VIH can overshoot to VCCQ+1.0 V for durations of 2 ns or less. 3. VPP <= VPPLK inhibits erase and program operations. Don't use VPPL and VPPH outside their valid ranges. 30 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics AC Characteristics Table 12. Read Operations - 90 nm Lithography (Sheet 1 of 2) Symbol 7.0 # Parameter (1,2) VCCQ= 1.7 V - 1.95 V Unit Notes - ns 7,8 Min Max 60 Asynchronous Specifications R1 tAVAV Read Cycle Time R2 tAVQV Address to Output Valid - 60 ns 7,8 R3 tELQV CE# Low to Output Valid - 60 ns 7,8 R4 tGLQV OE# Low to Output Valid - 20 ns 4 R5 tPHQV RST# High to Output Valid - 150 ns R6 tELQX CE# Low to Output Low-Z 0 - ns 5 R7 tGLQX OE# Low to Output Low-Z 0 - ns 4,5 R8 tEHQZ CE# High to Output High-Z - 14 ns 5 R9 tGHQZ OE# High to Output High-Z - 14 ns 4,5 R10 tOH CE# (OE#) High to Output Low-Z 0 - ns 4,5 Latching Specifications R101 tAVVH Address Setup to ADV# High 7 - ns R102 tELVH CE# Low to ADV# High 10 - ns R103 tVLQV ADV# Low to Output Valid - 60 ns R104 tVLVH ADV# Pulse Width Low 7 - ns R105 tVHVL ADV# Pulse Width High 7 - ns R106 tVHAX Address Hold from ADV# High 7 - ns R108 tAPA Page Address Access Time - 20 ns - 66 MHz 7,8 3 Clock Specifications R200 fCLK CLK Frequency R201 tCLK CLK Period 15 - ns R202 tCH/L CLK High or Low Time 3.5 - ns R203 tCHCL CLK Fall or Rise Time - 3 ns Preliminary Datasheet 31 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Read Operations - 90 nm Lithography (Sheet 2 of 2) # Symbol Table 12. Parameter (1,2) VCCQ= 1.7 V - 1.95 V Min Max Unit Notes Synchronous Specifications R301 tAVCH Address Valid Setup to CLK 7 - ns R302 tVLCH ADV# Low Setup to CLK 7 - ns R303 tELCH CE# Low Setup to CLK 7 - ns R304 tCHQV CLK to Output Valid - 11 ns R305 tCHQX Output Hold from CLK 3 - ns R306 tCHAX Address Hold from CLK 7 - ns 3 R307 tCHTV CLK to WAIT Valid - 11 ns 8 R308 tELTV CE# Low to WAIT Valid - 11 ns 6 R309 tEHTZ CE# High to WAIT High-Z - 11 ns 5,6 R310 tEHEL CE# Pulse Width High 14 - ns 6 1. 2. 3. 4. 5. 6. 7. 8. 32 8 See Figure 22, "AC Input/Output Reference Waveform" on page 54 for timing measurements and maximum allowable input slew rate. AC specifications assume the data bus voltage is less than or equal to VCCQ when a read operation is initiated. Address hold in synchronous-burst mode is defined as tCHAX or tVHAX, whichever timing specification is satisfied first. OE# may be delayed by up to tELQV- tGLQV after the falling edge of CE# without impact to tELQV. Sampled, not 100% tested. Applies only to subsequent synchronous reads. During the initial access of a synchronous burst read, data from the first word may begin to be driven onto the data bus as early as the first clock edge after tAVQV. All the preceding specifications apply to all densities. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics # Read Operations - 130 nm Lithography (Sheet 1 of 2) VCCQ= 1.35 V - 1.8 V Symbol Table 13. Parameter (1,2) -65 VCCQ= 1.7 V - 2.24 V -85 -60 -80 Unit Notes Min Max Min Max Min Max Min Max 65 - 85 - 60 - 80 - ns 7,8 - 85 - 60 - 80 ns 7,8 Asynchronous Specifications R1 tAVAV Read Cycle Time R2 tAVQV Address to Output Valid - 65 R3 tELQV CE# Low to Output Valid - 65 - 85 - 60 - 80 ns 7,8 R4 tGLQV OE# Low to Output Valid - 25 - 30 - 20 - 25 ns 4 R5 tPHQV RST# High to Output Valid - 150 - 150 - 150 - 150 ns R6 tELQX CE# Low to Output Low-Z 0 - 0 0 - 0 R7 tGLQX OE# Low to Output Low-Z 0 - 0 0 - 0 R8 tEHQZ CE# High to Output High-Z - 17 - 20 - 14 - R9 tGHQZ OE# High to Output High-Z - 14 - 14 - 14 - R10 tOH CE# (OE#) High to Output Low-Z 0 - 0 0 - ns 5 - ns 4,5 17 ns 5 14 ns 4,5 0 - ns 4,5 Latching Specifications R101 tAVVH Address Setup to ADV# High 7 - 7 - 7 - 7 - ns R102 tELVH CE# Low to ADV# High 10 - 10 - 10 - 10 - ns R103 tVLQV ADV# Low to Output Valid - 65 - 85 - 60 - 80 ns R104 tVLVH ADV# Pulse Width Low 7 - 7 - 7 - 7 - ns R105 tVHVL ADV# Pulse Width High 7 - 7 - 7 - 7 - ns R106 tVHAX Address Hold from ADV# High 7 - 7 - 7 - 7 - ns R108 tAPA Page Address Access Time - 25 - 30 - 20 - 25 ns - 54 - 40 - 66 - 54 MHz 7,8 3 Clock Specifications R200 fCLK CLK Frequency R201 tCLK CLK Period 18.5 - 25 - 15 - 18.5 - ns R202 tCH/L CLK High or Low Time 4.5 - 9.5 - 3.5 - 4.5 - ns R203 tCHCL CLK Fall or Rise Time - 3 - 3 - 3 - 3 ns Preliminary Datasheet 33 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics # Read Operations - 130 nm Lithography (Sheet 2 of 2) VCCQ= 1.35 V - 1.8 V Symbol Table 13. Parameter (1,2) -65 VCCQ= 1.7 V - 2.24 V -85 -60 Unit -80 Min Max Min Max Min Max Min Max Notes Synchronous Specifications R301 tAVCH Address Valid Setup to CLK 7 - 7 - 7 - 7 - ns R302 tVLCH ADV# Low Setup to CLK 7 - 7 - 7 - 7 - ns R303 tELCH CE# Low Setup to CLK 7 - 7 - 7 - 7 - ns R304 tCHQV CLK to Output Valid - 14 - 20 - 11 - 14 ns R305 tCHQX Output Hold from CLK 3 - 3 - 3 - 3 - ns R306 tCHAX Address Hold from CLK 7 - 7 - 7 - 7 - ns 3 R307 tCHTV CLK to WAIT Valid - 14 - 20 - 11 - 14 ns 8 R308 tELTV CE# Low to WAIT Valid - 14 - 20 - 11 - 14 ns 6 R309 tEHTZ CE# High to WAIT High-Z - 14 - 20 - 11 - 14 ns 5,6 R310 tEHEL CE# Pulse Width High 14 - 14 - 14 - 14 - ns 6 Note: 34 8 For all numbered note references in this table, refer to the notes in Table 12, "Read Operations - 90 nm Lithography" on page 31. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Table 14. Read Operations - 180 nm Lithography (Sheet 1 of 2) 32/64-Mbit # Parameter (1,2) Sym -70 128-Mbit -85 -85 Unit Min Max Min Max Min Max 70 - 85 - 85 - ns Notes Asynchronous Specifications R1 tAVAV Read Cycle Time R2 tAVQV Address to Output Delay - 70 - 85 - 85 ns R3 tELQV CE# Low to Output Delay - 70 - 85 - 85 ns R4 tGLQV OE# Low to Output Delay - 30 - 30 - 30 ns R5 tPHQV RST# High to Output Delay - 150 - 150 - 150 ns R6 tELQX CE# Low to Output in Low-Z 0 - 0 - 0 - ns 6 R7 tGLQX OE# Low to Output in Low-Z 0 - 0 - 0 - ns 5,6 R8 tEHQZ CE# High to Output in High-Z - 20 - 20 - 20 ns 6 R9 tGHQZ OE# High to Output in High-Z - 14 - 14 - 14 ns 5,6 R10 tOH CE# (OE#) High to Output in Low-Z 0 - 0 - 0 - ns 5,6 5 Latching Specifications R101 tAVVH Address Setup to ADV# High 10 - 10 - 10 - ns R102 tELVH CE# Low to ADV# High 10 - 10 - 10 - ns R103 tVLQV ADV# Low to Output Delay - 70 85 - 85 ns R104 tVLVH ADV# Pulse Width Low 10 - 10 - 10 - ns R105 tVHVL ADV# Pulse Width High 10 - 10 - 10 - ns R106 tVHAX Address Hold from ADV# High 9 - 9 - 9 - ns R108 tAPA Page Address Access Time - 20 - 25 - 25 ns 4 Clock Specifications R200 fCLK CLK Frequency - 52 - 40 - 40 MHz R201 tCLK CLK Period 19 - 25 - 25 - ns R202 tCH/L CLK High or Low Time 5 - 5 - 5 - ns R203 tCHCL CLK Fall or Rise Time - 3 - 3 - 3 ns Preliminary Datasheet 35 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Table 14. Read Operations - 180 nm Lithography (Sheet 2 of 2) 32/64-Mbit # Parameter (1,2) Sym -70 128-Mbit -85 -85 Unit Min Max Min Max Min Max Notes Synchronous Specifications R301 tAVCH Address Valid Setup to CLK 9 - 9 - 9 - ns R302 tVLCH ADV# Low Setup to CLK 10 - 10 - 10 - ns R303 tELCH CE# Low Setup to CLK 9 - 9 - 9 - ns R304 tCHQV CLK to Output Valid - 14 - 18 - 18 ns R305 tCHQX Output Hold from CLK 3.5 - 3.5 - 3.5 - ns R306 tCHAX Address Hold from CLK 10 - 10 - 10 - ns R307 tCHTV CLK to WAIT Valid - 14 - 18 - 18 ns R308 tELTV CE# Low to WAIT Valid - 14 - 18 - 18 ns 7 R309 tEHTZ CE# High to WAIT High-Z - 20 - 25 - 25 ns 6,7 R310 tEHEL CE# Pulse Width High 15 - 20 - 20 - ns 7 Note: 36 4 For all numbered note references in this table, refer to the notes in Table 12, "Read Operations - 90 nm Lithography" on page 31. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 8. Asynchronous Read Operation Waveform R1 Address [A] VIH Valid Address VIL R2 CE# [E] VIH VIL R3 OE# [G] R8 VIH R4 VIL R7 WE# [W] R9 VIH VIL WAIT [T] VOH High Z High Z Note 1 VOL Data [D/Q] VOH High Z Valid Output VOL R5 RST# [P] R10 VIH VIL Notes: 1. WAIT shown asserted (RCR[10]=0) 2. ADV# assumed to be driven to VIL in this waveform Preliminary Datasheet 37 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 9. Latched Asynchronous Read Operation Waveform R1 A[MAX:2] [A] VIH VIL A[1:0] [A] Valid Address Valid Address VIH Valid Address VIL Valid Address R2 R101 R105 ADV# [V] R106 VIH VIL R104 R103 CE# [E] VIH R3 VIL R102 R4 R8 R6 OE# [G] VIH VIL R7 WE# [W] R9 VIH VIL Data [Q] VOH High Z Valid Output VOL R5 RST# [P] R10 VIH VIL 38 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 10. Page-Mode Read Operation Waveform R1 A[MAX:2] [A] VIH Valid Address VIL R2 A[1:0] [A] VIH Valid Address VIL Valid Address Valid Address Valid Address R101 R105 ADV# [V] R106 VIH VIL R104 R103 CE# [E] VIH R3 VIL R102 R4 R8 R6 OE# [G] VIH VIL R7 WE# [W] R9 VIH VIL WAIT [T] VOH High Z Note 1 R108 High Z VOL Data [D/Q] VOH High Z Valid Output VOL R5 RST# [P] Valid Output Valid Output Valid Output R10 VIH VIL Note: WAIT shown asserted (RCR[10] = 0). Preliminary Datasheet 39 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 11. CLK [C] Single Synchronous Read-Array Operation Waveform VIH Note 1 VIL R301 Address [A] VIH R306 Valid Address VIL R2 R101 R105 ADV# [V] R106 VIH R302 VIL R104 R103 CE# [E] VIH R3 VIL R102 OE# [G] R4 R8 VIH VIL R303 WE# [W] R7 R9 VIH R309 VIL R308 WAIT [T] VOH High Z R10 High Z Note 2 VOL R304 Data [Q] VOH High Z R305 Valid Output VOL R5 RST# [P] VIH VIL Notes: 1. Section 14.2, "First Access Latency Count (RCR[13:11])" on page 91 describes how to insert clock cycles during the initial access. 2. WAIT (shown asserted; RCR[10]=0) can be configured to assert either during, or one data cycle before, valid data. 3. This waveform illustrates the case in which an x-word burst is initiated to the main array and it is terminated by a CE# deassertion after the first word in the burst. If this access had been done to Status, ID, or Query reads, the asserted (low) WAIT signal would have remained asserted (low) as long as CE# is asserted (low). 40 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 12. CLK [C] Synchronous 4-Word Burst Read Operation Waveform VIH VIL 0 R301 Address [A] Note 1 1 VIH R306 Valid Address VIL R2 R101 R105 ADV# [V] R106 VIH R302 VIL R104 R103 CE# [E] VIH R310 R3 VIL R102 OE# [G] R4 R8 VIH VIL R303 WE# [W] R7 R9 VIH R309 R308 VIL R10 R307 WAIT [T] VOH High Z Hig h Z Note 2 VOL R304 Data [Q] VOH High Z R305 Valid Output VOL Valid Outpu t Valid Output Valid Output High Z R5 RST# [P] VIH VIL Notes: 1. Section 14.2, "First Access Latency Count (RCR[13:11])" on page 91 describes how to insert clock cycles during the initial access. 2. WAIT (shown asserted; RCR[10] = 0) can be configured to assert either during, or one data cycle before, valid data. Preliminary Datasheet 41 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 13. WAIT Functionality for EOWL (End-of-Word Line) Condition Waveform VIH CLK [C] VIL 0 R301 VIH Address [A] Note 1 1 R306 Valid Address VIL R2 R101 R105 ADV# [V] R106 VIH R302 VIL R104 R103 CE# [E] VIH R3 VIL R102 OE# [G] R4 VIH VIL R303 WE# [W] R7 VIH R308 VIL R307 WAIT [T] VOH High Z High Z Note 2 VOL R304 Data [D/Q] VOH High Z R305 Valid Output VOL Valid Output Valid Output Valid Output R5 RST# [P] VIH VIL Notes: 1. Section 14.2, "First Access Latency Count (RCR[13:11])" on page 91 describes how to insert clock cycles during the initial access. 2. WAIT (shown asserted; RCR[10]=0) can be configured to assert either during, or one data cycle before, valid data (assumed wait delay of two clocks, for example). 42 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 14. CLK [C] WAIT Signal in Synchronous Non-Read Array Operation Waveform VIH Note 1 VIL R301 Address [A] VIH R306 Valid Address VIL R2 R101 R105 ADV# [V] R106 VIH R302 VIL R104 R103 CE# [E] VIH R3 VIL R102 OE# [G] R4 R8 VIH VIL R303 WE# [W] R7 R9 VIH R309 VIL R308 WAIT [T] VOH High Z R10 High Z Note 2 VOL R304 Data [Q] VOH High Z R305 Valid Output VOL R5 RST# [P] VIH VIL Notes: 1. Section 14.2, "First Access Latency Count (RCR[13:11])" on page 91 describes how to insert clock cycles during the initial access. 2. WAIT shown asserted (RCR[10]=0). Preliminary Datasheet 43 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 15. Burst Suspend R304 R305 R305 R305 CLK R1 R2 Address [A] R101 R105 R106 ADV# R3 R8 CE# [E] R4 R9 R4 R9 OE# [G] R13 R12 WAIT [T] WE# [W] R7 R6 DATA [D/Q] Q0 Note: 44 R304 Q1 Q1 R304 Q2 During Burst Suspend, Clock signal can be held high or low. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics 7.1 AC Write Characteristics Table 15. AC Write Characteristics - 90 nm Lithography # Sym Parameter (1,2) VCCQ = 1.7 V - 1.95 V Min Unit Notes 3 Max W1 tPHWL (tPHEL) RST# High Recovery to WE# (CE#) Low 150 - ns W2 tELWL (tWLEL) CE# (WE#) Setup to WE# (CE#) Low 0 - ns W3 tWLWH (tELEH) WE# (CE#) Write Pulse Width Low 40 - ns W4 tDVWH (tDVEH) Data Setup to WE# (CE#) High 40 - ns W5 tAVWH (tAVEH) Address Setup to WE# (CE#) High 40 - ns W6 tWHEH (tEHWH) CE# (WE#) Hold from WE# (CE#) High 0 - ns W7 tWHDX (tEHDX) Data Hold from WE# (CE#) High 0 - ns W8 tWHAX (tEHAX) Address Hold from WE# (CE#) High 0 - ns 4 W9 tWHWL (tEHEL) WE# (CE#) Pulse Width High 20 - ns 5,6,7 W10 tVPWH (tVPEH) VPP Setup to WE# (CE#) High 200 - ns 3 W11 tQVVL VPP Hold from Valid SRD 0 - ns 3,8 W12 tQVBL WP# Hold from Valid SRD 0 - ns 3,8 W13 tBHWH (tBHEH) WP# Setup to WE# (CE#) High 3 W14 tWHGL (tEHGL) Write Recovery before Read W16 tWHQV WE# High to Valid Data W18 tWHAV W19 W20 200 - ns 0 - ns tAVQV +20 - ns 3,6,10 WE# High to Address Valid 0 - ns 3,9,10 tWHCV WE# High to CLK Valid 12 - ns 3,10 tWHVH WE# High to ADV# High 12 - ns 3,10 Notes: 1. Write timing characteristics during erase suspend are the same as during write-only operations. 2. A write operation can be terminated with either CE# or WE#. 3. Sampled, not 100% tested. 4. Write pulse width low (tWLWH or tELEH) is defined from CE# or WE# low (whichever occurs last) to CE# or WE# high (whichever occurs first). Hence, tWLWH = tELEH = tWLEH = tELWH. 5. Write pulse width high (tWHWL or tEHEL) is defined from CE# or WE# high (whichever is first) to CE# or WE# low (whichever is last). Hence, tWHWL = tEHEL = tWHEL = tEHWL. 6. System designers should take this into account and may insert a software No-Op instruction to delay the first read after issuing a command. 7. For commands other than resume commands. 8. VPP should be held at VPP1 or VPP2 until block erase or program success is determined. 9. Applicable during asynchronous reads following a write. 10. tWHCH/L OR tWHVH must be met when transitioning from a write cycle to a synchronous burst read. tWHCH/L and tWHVH both refer to the address latching event (either the rising/falling clock edge or the rising ADV# edge, whichever occurs first). Preliminary Datasheet 45 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Table 16. AC Write Characteristics - 130 nm Lithography VCCQ = 1.35 V - 1.8 V # Sym Parameter (1,2) -65 VCCQ = 1.7 V - 2.24 V -85 -60 -80 Unit Notes 3 Min Max Min Max Min Max Min Max 150 - 150 - 150 - 150 - ns W1 tPHWL (tPHEL) RST# High Recovery to WE# (CE#) Low W2 tELWL (tWLEL) CE# (WE#) Setup to WE# (CE#) Low 0 - 0 - 0 - 0 - ns W3 tWLWH (tELEH) WE# (CE#) Write Pulse Width Low 50 - 60 - 40 - 60 - ns W4 tDVWH (tDVEH) Data Setup to WE# (CE#) High 50 - 60 - 40 - 60 - ns W5 tAVWH (tAVEH) Address Setup to WE# (CE#) High 50 - 60 - 40 - 60 - ns W6 tWHEH (tEHWH) CE# (WE#) Hold from WE# (CE#) High 0 - 0 - 0 - 0 - ns W7 tWHDX (tEHDX) Data Hold from WE# (CE#) High 0 - 0 - 0 - 0 - ns W8 tWHAX (tEHAX) Address Hold from WE# (CE#) High 0 - 0 - 0 - 0 - ns W9 tWHWL (tEHEL) WE# (CE#) Pulse Width High 20 - 25 - 20 - 25 - ns W10 tVPWH (tVPEH) VPP Setup to WE# (CE#) High 200 - 200 - 200 - 200 - ns 3 W11 tQVVL VPP Hold from Valid SRD 0 - 0 - 0 - 0 - ns 3,8 W12 tQVBL WP# Hold from Valid SRD 0 - 0 - 0 - 0 - ns 3,8 W13 tBHWH (tBHEH) WP# Setup to WE# (CE#) High 200 - 200 - 200 - 200 - ns 3 W14 tWHGL (tEHGL) Write Recovery before Read 0 4 5,6,7 - 0 - 0 - 0 - ns tAVQV + 25 - tAVQV + 55 - tAVQV +20 - tAVQV +50 - ns 3,6,10 W16 tWHQV WE# High to Valid Data W18 tWHAV WE# High to Address Valid 0 - 0 - 0 - 0 - ns 3,9,10 W19 tWHCV WE# High to CLK Valid 16 - 20 - 12 - 20 - ns 3,10 W20 tWHVH WE# High to ADV# High 16 - 20 - 12 - 20 - ns 3,10 Notes: For all numbered note references in this table, refer to the notes in Table 15, "AC Write Characteristics - 90 nm Lithography" on page 45. 46 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Table 17. AC Write Characteristics - 180 nm Lithography VCCQ = 1.7 V - 2.24 V # Parameter (1,2) Sym -70 -85 Unit Notes 3 Min Max Min Max 150 - 150 - ns W1 tPHWL (tPHEL) RST# High Recovery to WE# (CE#) Low W2 tELWL (tWLEL) CE# (WE#) Setup to WE# (CE#) Low 0 - 0 - ns W3 tWLWH (tELEH) WE# (CE#) Write Pulse Width Low 45 - 60 - ns W4 tDVWH (tDVEH) Data Setup to WE# (CE#) High 45 - 60 - ns W5 tAVWH (tAVEH) Address Setup to WE# (CE#) High 45 - 60 - ns W6 tWHEH (tEHWH) CE# (WE#) Hold from WE# (CE#) High 0 - 0 - ns W7 tWHDX (tEHDX) Data Hold from WE# (CE#) High 0 - 0 - ns 4 W8 tWHAX (tEHAX) Address Hold from WE# (CE#) High 0 - 0 - ns W9 tWHWL (tEHEL) WE# (CE#) Pulse Width High 25 - 25 - ns 5,6,7 W10 tVPWH (tVPEH) VPP Setup to WE# (CE#) High 200 - 200 - ns 3 W11 tQVVL VPP Hold from Valid SRD 0 - 0 - ns 3,8 W12 tQVBL WP# Hold from Valid SRD W13 tBHWH (tBHEH) WP# Setup to WE# (CE#) High W14 tWHGL (tEHGL) Write Recovery before Read W16 tWHQV WE# High to Valid Data W18 tWHAV W19 W20 0 - 0 - ns 3,8 200 - 200 - ns 3 0 - 0 - ns tAVQV + 40 - tAVQV + 50 - ns 3,6,10 WE# High to Address Valid 0 - 0 ns 3,9,10 tWHCV WE# High to CLK Valid 20 - 20 - ns 3,10 tWHVH WE# High to ADV# High 20 - 20 - ns 3,10 Notes: For all numbered note references in this table, refer to the notes in Table 15, "AC Write Characteristics - 90 nm Lithography" on page 45. Preliminary Datasheet 47 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 16. Write Operations Waveform CLK [C] VIH VIL W19 Note 1 Address [A] VIH VIL Note 2 Note 3 Valid Address Note 4 Valid Address Note 5 Valid Address W5 W18 R101 R105 ADV# [V] R106 W8 VIH VIL R104 CE# (WE#) [E(W)] W20 VIH Note 6 VIL W2 OE# [G] W6 VIH VIL W3 W14 W9 WE# (CE#) [W(E)] VIH Note 6 VIL W1 Data [Q] W7 W16 VIH Data In Valid SRD Data In VIL W4 RST# [P] VIH VIL WP# [B] W13 W12 W10 W11 VIH VIL VPPH VPP [V] VPPLK VIL Notes: 1. 2. 3. 4. 5. 6. 7. 48 VCC power-up and standby. Write Program or Erase Setup command. Write valid address and data (for program) or Erase Confirm command. Automated program/erase delay. Read Status Register data (SRD) to determine program/erase operation completion. OE# and CE# must be asserted and WE# must be deasserted for read operations. CLK is ignored. (but may be kept active/toggling) Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 17. Asynchronous Read to Write Operation Waveform R1 R2 W5 W8 Address [A] R3 R8 CE# [E} R4 R9 OE# [G] W3 W2 W6 WE# [W] R7 R6 W7 R10 Data [D/Q] W4 D Q R5 RST# [P] Figure 18. Asynchronous Write to Read Operation W5 W8 R1 Address [A] W2 W6 R10 CE# [E} W3 W18 WE# [W] W14 OE# [G] W7 W4 Data [D/Q] D R4 R2 R3 R9 R8 Q W1 RST # [P] Preliminary Datasheet 49 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 19. Synchronous Read to Write Operation Latency Count R301 R302 R306 CLK [C] R2 W5 R101 W18 Address [A] R105 R106 R104 R102 W20 ADV# [V] R303 R3 R11 W6 CE# [E] R4 R8 OE# [G] W15 W19 W9 W8 W3 W2 WE# R12 R307 WAIT [T] R304 R13 R7 Data [D/Q] 50 R305 Q W7 D D Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics Figure 20. Synchronous Write To Read Operation Latency Count R302 R301 R2 CLK W5 W8 R306 Address [A] W20 R106 R104 ADV# W6 W2 R303 R11 CE# [E} W18 W19 W3 WE# [W] R4 OE# [G ] R12 R307 WAIT [T] W7 W4 Data [D/Q ] R304 R3 D Q R304 R305 Q W1 RST# [P] Preliminary Datasheet 51 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics 7.2 Erase and Program Times Table 18. Erase and Program Times Operation Symbol Description (1) Parameter VPP1 VPP2 Notes Unit Typ Max Typ Max Erasing and Suspending W500 tERS/PB 4-Kword Parameter Block 2,3 0.3 2.5 0.25 2.5 s W501 tERS/MB 32-Kword Main Block 2,3 0.7 4 0.4 4 s W600 tSUSP/P Program Suspend 2 5 10 5 10 s W601 tSUSP/E Erase Suspend 2 5 20 5 20 s W200 tPROG/W Single Word 2 12 150 8 130 s W201 tPROG/PB 4-Kword Parameter Block 2,3 0.05 .23 0.03 0.07 s W202 tPROG/MB 32-Kword Main Block 2,3 0.4 1.8 0.24 0.6 s 4 N/A N/A 3.1 16 s - 15 - ms Erase Time Suspend Latency Programming Program Time Enhanced Factory Programming Program Operation Latency (5) W400 tEFP/W Single Word W401 tEFP/PB 4-Kword Parameter Block 2,3 N/A W402 tEFP/MB 32-Kword Main Block 2,3 N/A - 120 - ms W403 tEFP/SETUP EFP Setup - N/A - 5 s W404 tEFP/TRAN Program to Verify Transition N/A N/A 2.7 5.6 s W405 tEFP/VERIFY Verify N/A N/A 1.7 130 s Notes: 1. Unless noted otherwise, all parameters are measured at TA = +25 C and nominal voltages, and they are sampled, not 100% tested. 2. Excludes external system-level overhead. 3. Exact results may vary based on system overhead. 4. W400-Typ is the calculated delay for a single programming pulse. W400-Max includes the delay when programming within a new word-line. 5. Some EFP performance degradation may occur if block cycling exceeds 10. 52 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics 7.3 Reset Specifications Table 19. Reset Specifications # P1 tPLPH P2 tPLRH P3 Notes: 1. 2. 3. 4. 5. 6. Parameter (1) Symbol tVCCPH Notes Min Max Unit RST# Low to Reset during Read 1, 2, 3, 4 100 - ns RST# to 1, 3, 4, 5 - s RST# to Reset during 1, 3, 4, 5 - s VCC Power Valid to Reset 1,3,4,5,6 60 - s These specifications are valid for all product versions (packages and speeds). The device may reset if tPLPH< tPLPHMin, but this is not guaranteed. Not applicable if RST# is tied to VCC. Sampled, but not 100% tested. If RST# is tied to VCC, the device is not ready until tVCCPH occurs after when VCC VCCMin. If RST# is tied to any supply/signal with VCCQ voltage levels, the RST# input voltage must not exceed VCC until VCC VCCMin. Figure 21. Reset Operations Waveforms P1 (A) Reset during read mode RST# [P] VIH VIL P2 (B) Reset during program or block erase P1 P2 RST# [P] Abort Complete R5 VIH VIL P2 (C) Reset during program or block erase P1 P2 R5 RST# [P] Abort Complete R5 VIH VIL P3 (D) VCC Power-up to RST# high Preliminary Datasheet VCC VCC 0V 53 Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics 7.4 AC I/O Test Conditions Figure 22. AC Input/Output Reference Waveform VCCQ Input Test Points VCCQ/2 VCCQ/2 Output 0V Note: Figure 23. Input timing begins, and output timing ends, at VCCQ/2. Input rise and fall times (10% to 90%) < 5 ns. Worst case speed conditions are when VCC = VCCMin. Transient Equivalent Testing Load Circuit VCCQ R1 Device Under Test Out CL Note: Table 20. See Table 19 for component values. Test Configuration Component Values for Worst Case Speed Conditions Test Configuration Note: Figure 24. R2 CL (pF) R1 (k) R2 (k) 30 13.5 13.5 30 16.7 16.7 CL includes jig capacitance. Clock Input AC Waveform R201 CLK [C] VIH VIL R202 54 R203 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 7.0 AC Characteristics 7.5 Device Capacitance TA = +25 C, f = 1 MHz Symbol Parameter Typ Max Unit Condition CIN Input Capacitance 6 8 pF VIN = 0.0 V COUT Output Capacitance 8 12 pF VOUT = 0.0 V CCE CE# Input Capacitance 10 12 pF VIN = 0.0 V Sampled, not 100% tested. Preliminary Datasheet 55 Intel(R) Wireless Flash Memory (W18) 8.0 Power and Reset Specifications 8.0 Power and Reset Specifications Intel(R) Wireless Flash Memory (W18) devices have a layered approach to power savings that can significantly reduce overall system power consumption. The APS feature reduces power consumption when the device is selected but idle. If CE# is deasserted, the memory enters its standby mode, where current consumption is even lower. Asserting RST# provides current savings similar to standby mode. The combination of these features can minimize memory power consumption, and therefore, overall system power consumption. 8.1 Active Power With CE# at VIL and RST# at VIH, the device is in the active mode. Refer to Section 6.1, "DC Current Characteristics" on page 28, for ICC values. When the device is in "active" state, it consumes the most power from the system. Minimizing device active current therefore reduces system power consumption, especially in battery-powered applications. 8.2 Automatic Power Savings (APS) Automatic Power Saving (APS) provides low-power operation during a read's active state. During APS mode, ICCAPS is the average current measured over any 5 ms time interval 5 s after the following events happen: * There is no internal sense activity; * CE# is asserted; * The address lines are quiescent, and at VSSQ or VCCQ. OE# may be asserted during APS. 8.3 Standby Power With CE# at VIH and the device in read mode, the flash memory is in standby mode, which disables most device circuitry and substantially reduces power consumption. Outputs are placed in a highimpedance state independent of the OE# signal state. If CE# transitions to VIH during erase or program operations, the device continues the operation and consumes corresponding active power until the operation is complete. ICCS is the average current measured over any 5 ms time interval 5 s after a CE# de-assertion. 8.4 Power-Up/Down Characteristics The device is protected against accidental block erasure or programming during power transitions. Power supply sequencing is not required if VCC, VCCQ, and VPP are connected together; so it doesn't matter whether VPP or VCC powers-up first. If VCCQ and/or VPP are not connected to the system supply, then VCC should attain VCCMIN before applying VCCQ and VPP. Device inputs should not be driven before supply voltage = VCCMIN. Power supply transitions should only occur when RST# is low. 56 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 8.0 Power and Reset Specifications 8.4.1 System Reset and RST# The use of RST# during system reset is important with automated program/erase devices because the system expects to read from the flash memory when it comes out of reset. If a CPU reset occurs without a flash memory reset, proper CPU initialization will not occur because the flash memory may be providing status information instead of array data. To allow proper CPU/flash initialization at system reset, connect RST# to the system CPU RESET# signal. System designers must guard against spurious writes when VCC voltages are above VLKO. Because both WE# and CE# must be low for a command write, driving either signal to VIH inhibits writes to the device. The CUI architecture provides additional protection because alteration of memory contents can only occur after successful completion of the two-step command sequences. The device is also disabled until RST# is brought to VIH, regardless of its control input states. By holding the device in reset (RST# connected to system PowerGood) during power-up/down, invalid bus conditions during power-up can be masked, providing yet another level of memory protection. 8.4.2 VCC, VPP, and RST# Transitions The CUI latches commands issued by system software and is not altered by VPP or CE# transitions or WSM actions. Read-array mode is its power-up default state after exit from reset mode or after VCC transitions above VLKO (Lockout voltage). After completing program or block erase operations (even after VPP transitions below VPPLK), the Read Array command must reset the CUI to read-array mode if flash memory array access is desired. 8.5 Power Supply Decoupling When the device is accessed, many internal conditions change. Circuits are enabled to charge pumps and switch voltages. This internal activity produces transient noise. To minimize the effect of this transient noise, device decoupling capacitors are required. Transient current magnitudes depend on the device outputs' capacitive and inductive loading. Two-line control and proper decoupling capacitor selection suppresses these transient voltage peaks. Each flash device should have a 0.1 F ceramic capacitor connected between each power (VCC, VCCQ, VPP), and ground (VSS, VSSQ) signal. High-frequency, inherently low-inductance capacitors should be as close as possible to package signals. Preliminary Datasheet 57 Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview 9.0 Bus Operations Overview This section provides an overview of device bus operations. The Intel(R) Wireless Flash Memory (W18) family includes an on-chip WSM to manage block erase and program algorithms. Its Command User Interface (CUI) allows minimal processor overhead with RAM-like interface timings. Device commands are written to the CUI using standard microprocessor timings. 9.1 Bus Operations Bus cycles to/from the W18 device conform to standard microprocessor bus operations. Table 21 summarizes the bus operations and the logic levels that must be applied to the device's control signal inputs. Table 21. Bus Operations Summary Bus Operation RST# CLK ADV# CE# OE# WE# WAIT DQ[15:0] Asynchronous VIH X L L L H Asserted Output Synchronous VIH Running L L L H Driven Output Burst Suspend VIH Halted X L H H Active Output Write VIH X L L H L Asserted Input 2 Output Disable VIH X X L H H Asserted High-Z 3 Standby VIH X X H X X High-Z High-Z 3 Reset VIL X X X X X High-Z High-Z 3,4 Read Notes: 1. 2. 3. 4. 9.1.1 Notes 1 WAIT is only valid during synchronous array-read operations. Refer to the Table 23, "Bus Cycle Definitions" on page 63 for valid DQ[15:0] during a write operation. X = Don't Care (H or L). RST# must be at VSS 0.2 V to meet the maximum specified power-down current. Reads Device read operations are performed by placing the desired address on A[22:0] and asserting CE# and OE#. ADV# must be low, and WE# and RST# must be high. All read operations are independent of the voltage level on VPP. CE#-low selects the device and enables its internal circuits. OE#-low or WE#-low determine whether DQ[15:0] are outputs or inputs, respectively. OE# and WE# must not be low at the same time - indeterminate device operation will result. In asynchronous-page mode, the rising edge of ADV# can be used to latch the address. If only asynchronous read mode is used, ADV# can be tied to ground. CLK is not used in asynchronouspage mode and should be tied high. In synchronous-burst mode, ADV# is used to latch the initial address - either on the rising edge of ADV# or the rising (or falling) edge of CLK with ADV# low, whichever occurs first. CLK is used in synchronous-burst mode to increment the internal address counter, and to output read data on DQ[15:0]. Each device partition can be placed in any of several read states: 58 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview * Read Array: Returns flash array data from the addressed location. * Read Identifier (ID): Returns manufacturer ID and device ID codes, block lock status, and protection register data. Read Identifier information can be accessed from any 4-Mbit partition base address. * CFI Query: Returns Common Flash Interface (CFI) information. CFI information can be accessed starting at 4-Mbit partition base addresses. * Read Status Register: Returns Status Register (SR) data from the addressed partition. The appropriate CUI command must be written to the partition in order to place it in the desired read state (see Table 22, "Command Codes and Descriptions" on page 61). Non-array read operations (Read ID, CFI Query, and Read Status Register) execute as single synchronous or asynchronous read cycles. WAIT is asserted throughout non-array read operations. 9.1.2 Writes Device write operations are performed by placing the desired address on A[22:0] and asserting CE# and WE#. OE# and RST# must be high. Data to be written at the desired address is placed on DQ[15:0]. ADV# must be held low throughout the write cycle or it can be toggled to latch the address. If ADV# is held low, the address and data are latched on the rising edge of WE#. CLK is not used during write operations, and is ignored; it can be either free-running or halted at VIL or VIH. All write operations are asynchronous. Table 22, "Command Codes and Descriptions" on page 61 shows the available device commands. Appendix A, "Write State Machine States" on page 98 provides information on moving between different device operations by using CUI commands. 9.1.3 Output Disable When OE# is deasserted, device outputs DQ[15:0] are disabled and placed in a high-impedance (High-Z) state. 9.1.4 Burst Suspend The Burst Suspend feature allows the system to temporarily suspend a synchronous-burst read operation. This can be useful if the system needs to access another device on the same address and data bus as the flash during a burst-read operation. Synchronous-burst accesses can be suspended during the initial latency (before data is received) or after the device has output data. When a burst access is suspended, internal array sensing continues and any previously latched internal data is retained. Burst Suspend occurs when CE# is asserted, the current address has been latched (either ADV# rising edge or valid CLK edge), CLK is halted, and OE# is deasserted. CLK can be halted when it is at VIH or VIL. To resume the burst access, OE# is reasserted and CLK is restarted. Subsequent CLK edges resume the burst sequence where it left off. Within the device, CE# gates WAIT. Therefore, during Burst Suspend WAIT is still driven. This can cause contention with another device attempting to control the system's READY signal during a Burst Suspend. Systems using the Burst Suspend feature should not connect the device's WAIT signal directly to the system's READY signal. Refer to Figure 15, "Burst Suspend" on page 44. Preliminary Datasheet 59 Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview 9.1.5 Standby De-asserting CE# deselects the device and places it in standby mode, substantially reducing device power consumption. In standby mode, outputs are placed in a high-impedance state independent of OE#. If deselected during a program or erase algorithm, the device shall consume active power until the program or erase operation completes. 9.1.6 Reset The device enters a reset mode when RST# is asserted. In reset mode, internal circuitry is turned off and outputs are placed in a high-impedance state. After returning from reset, a time tPHQV is required until outputs are valid, and a delay (tPHWV) is required before a write sequence can be initiated. After this wake-up interval, normal operation is restored. The device defaults to read-array mode, the Status Register is set to 80h, and the Configuration Register defaults to asynchronous page-mode reads. If RST# is asserted during an erase or program operation, the operation aborts and the memory contents at the aborted block or address are invalid. See Figure 21, "Reset Operations Waveforms" on page 53 for detailed information regarding reset timings. Like any automated device, it is important to assert RST# during system reset. When the system comes out of reset, the processor expects to read from the flash memory array. Automated flash memories provide status information when read during program or erase operations. If a CPU reset occurs with no flash memory reset, proper CPU initialization may not occur because the flash memory may be providing status information instead of array data. Intel flash memories allow proper CPU initialization following a system reset through the use of the RST# input. In this application, RST# is controlled by the same CPU reset signal. 9.2 Device Commands The device's on-chip WSM manages erase and program algorithms. This local CPU (WSM) controls the device's in-system read, program, and erase operations. Bus cycles to or from the flash memory conform to standard microprocessor bus cycles. RST#, CE#, OE#, WE#, and ADV# control signals dictate data flow into and out of the device. WAIT informs the CPU of valid data during burst reads. Table 21, "Bus Operations Summary" on page 58 summarizes bus operations. Device operations are selected by writing specific commands into the device's CUI. Table 22, "Command Codes and Descriptions" on page 61 lists all possible command codes and descriptions. Table 23, "Bus Cycle Definitions" on page 63 lists command definitions. Because commands are partition-specific, it is important to issue write commands within the target address range. 60 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview Table 22. Operation Read Command Codes and Descriptions (Sheet 1 of 2) Device Command Code Description FFh Read Array Places selected partition in Read Array mode. 70h Read Status Register Places selected partition in Status Register read mode. After issuing this command, reading from the partition outputs SR data on DQ[15:0]. A partition automatically enters this mode after issuing the Program or Erase command. 90h Read Identifier Places the selected partition in Read ID mode. Device reads from partition addresses output manufacturer/device codes, Configuration Register data, block lock status, or protection register data on DQ[15:0]. 98h CFI Query Puts the addressed partition in CFI Query mode. Device reads from the partition addresses output CFI information on DQ[7:0]. 50h Clear Status Register The WSM can set the Status Register's block lock (SR[1]), VPP (SR[3]), program (SR[4]), and erase (SR[5]) status bits, but it cannot clear them. SR[5:3,1] can only be cleared by a device reset or through the Clear Status Register command. 40h Word Program Setup This preferred program command's first cycle prepares the CUI for a program operation. The second cycle latches address and data, and executes the WSM program algorithm at this location. Status register updates occur when CE# or OE# is toggled. A Read Array command is required to read array data after programming. 10h Alternate Setup Equivalent to a Program Setup command (40h). 30h EFP Setup This program command activates EFP mode. The first write cycle sets up the command. If the second cycle is an EFP Confirm command (D0h), subsequent writes provide program data. All other commands are ignored after EFP mode begins. D0h EFP Confirm If the first command was EFP Setup (30h), the CUI latches the address and data, and prepares the device for EFP mode. Erase Setup This command prepares the CUI for Block Erase. The device erases the block addressed by the Erase Confirm command. If the next command is not Erase Confirm, the CUI sets Status Register bits SR[5:4] to indicate command sequence error and places the partition in the read Status Register mode. D0h Erase Confirm If the first command was Erase Setup (20h), the CUI latches address and data, and erases the block indicated by the erase confirm cycle address. During program or erase, the partition responds only to Read Status Register, Program Suspend, and Erase Suspend commands. CE# or OE# toggle updates Status Register data. B0h Program Suspend or Erase Suspend This command, issued at any device address, suspends the currently executing program or erase operation. Status register data indicates the operation was successfully suspended if SR[2] (program suspend) or SR[6] (erase suspend) and SR[7] are set. The WSM remains in the suspended state regardless of control signal states (except RST#). D0h Suspend Resume This command, issued at any device address, resumes the suspended program or erase operation. Program 20h Erase Suspend Preliminary Datasheet 61 Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview Table 22. Operation Command Codes and Descriptions (Sheet 2 of 2) Code Device Command Description 60h Lock Setup This command prepares the CUI lock configuration. If the next command is not Lock Block, Unlock Block, or Lock-Down, the CUI sets SR[5:4] to indicate command sequence error. 01h Lock Block If the previous command was Lock Setup (60h), the CUI locks the addressed block. D0h Unlock Block If the previous command was Lock Setup (60h), the CUI latches the address and unlocks the addressed block. If previously locked-down, the operation has no effect. 2Fh Lock-Down If the previous command was Lock Setup (60h), the CUI latches the address and locks-down the addressed block. C0h Protection Program Setup This command prepares the CUI for a protection register program operation. The second cycle latches address and data, and starts the WSM's protection register program or lock algorithm. Toggling CE# or OE# updates the flash Status Register data. To read array data after programming, issue a Read Array command. 60h Configuration Setup This command prepares the CUI for device configuration. If Set Configuration Register is not the next command, the CUI sets SR[5:4] to indicate command sequence error. 03h Set Configuration Register If the previous command was Configuration Setup (60h), the CUI latches the address and writes the data from A[15:0] into the configuration register. Subsequent read operations access array data. Block Locking Protection Configuration Note: 62 Do not use unassigned commands. Intel reserves the right to redefine these codes for future functions. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview Table 23. Bus Cycle Definitions Operation Read Command Lock First Bus Cycle Second Bus Cycle Oper Addr1 Data2,3 Oper Addr1 Data2,3 Read Array/Reset 1 Write PnA FFh Read Read Address Array Data Read Identifier 2 Write PnA 90h Read PBA+IA IC CFI Query 2 Write PnA 98h Read PBA+QA QD 2 Write PnA 70h Read PnA SRD Read Status Register Program and Erase Bus Cycles Clear Status Register 1 Write XX 50h Block Erase 2 Write BA 20h Write BA D0h Word Program 2 Write WA 40h/10h Write WA WD EFP >2 Write WA 30h Write WA D0h Program/Erase Suspend 1 Write XX B0h Program/Erase Resume 1 Write XX D0h Lock Block 2 Write BA 60h Write BA 01h Unlock Block 2 Write BA 60h Write BA D0h Lock-Down Block 2 Write BA 60h Write BA 2Fh Protection Program 2 Write PA C0h Write PA PD Lock Protection Program 2 Write LPA C0h Write LPA FFFDh Set Configuration Register 2 Write CD 60h Write CD 03h Protection Configuration Notes: 1. First-cycle command addresses should be the same as the operation's target address. Examples: the first-cycle address for the Read Identifier command should be the same as the Identification code address (IA); the first-cycle address for the Word Program command should be the same as the word address (WA) to be programmed; the first-cycle address for the Erase/Program Suspend command should be the same as the address within the block to be suspended; etc. XX = Any valid address within the device. IA = Identification code address. BA = Block Address. Any address within a specific block. LPA = Lock Protection Address is obtained from the CFI (through the CFI Query command). The Intel Wireless Flash Memory family's LPA is at 0080h. PA = User programmable 4-word protection address. PnA = Any address within a specific partition. PBA = Partition Base Address. The very first address of a particular partition. QA = CFI code address. WA = Word address of memory location to be written. 2. SRD = Status register data. WD = Data to be written at location WA. IC = Identifier code data. PD = User programmable 4-word protection data. QD = Query code data on DQ[7:0]. CD = Configuration register code data presented on device addresses A[15:0]. A[MAX:16] address bits can select any partition. See Table 31, "Read Configuration Register Descriptions" on page 89 for Configuration Register bits descriptions. 3. Commands other than those shown above are reserved by Intel for future device implementations and should not be used. Preliminary Datasheet 63 Intel(R) Wireless Flash Memory (W18) 9.0 Bus Operations Overview 9.3 Command Sequencing When issuing a 2-cycle write sequence to the flash device, a read operation is allowed to occur between the two write cycles. The setup phase of a 2-cycle write sequence places the addressed partition into read-status mode, so if the same partition is read before the second "confirm" write cycle is issued, Status Register data will be returned. Reads from other partitions, however, can return actual array data assuming the addressed partition is already in read-array mode. Figure 25 on page 64 and Figure 26 on page 64 illustrate these two conditions. Figure 25. Normal Write and Read Cycles Address [A] Partition A Partition A Partition A WE# [W] OE# [G] Data [Q] Figure 26. 20h D0h FFh Block Erase Setup Block Erase Conf irm Read Array Interleaving a 2-Cycle Write Sequence with an Array Read Address [A] Partition B Partition A Partition B Partition A WE# [W] OE# [G] Data [Q] FFh 20h Array Data D0h Read Array Erase Setup Bus Read Erase Conf irm By contrast, a write bus cycle may not interrupt a 2-cycle write sequence. Doing so causes a command sequence error to appear in the Status Register. Figure 27 illustrates a command sequence error. Figure 27. Improper Command Sequencing Address [A] Partition X Partitio n Y Partition X Partition X WE# [W] OE# [G] Data [D/Q] 64 20h FFh D0h SR Data Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 10.0 Read Operations 10.0 Read Operations The device supports two read modes - asynchronous page and synchronous burst mode. Asynchronous page mode is the default read mode after device power-up or a reset. The Read Configuration Register (RCR) must be configured to enable synchronous burst reads of the flash memory array (see Section 14.0, "Set Read Configuration Register" on page 89). Each partition of the device can be in any of four read states: Read Array, Read Identifier, Read Status or CFI Query. Upon power-up, or after a reset, all partitions of the device default to the Read Array state. To change a partition's read state, the appropriate read command must be written to the device (see Section 9.2, "Device Commands" on page 60). The following sections describe device read modes and read states in detail. 10.1 Asynchronous Page Read Mode Following a device power-up or reset, asynchronous page mode is the default read mode and all partitions are set to Read Array. However, to perform array reads after any other device operation (e.g. write operation), the Read Array command must be issued in order to read from the flash memory array. Note: Asynchronous page-mode reads can only be performed when Read Configuration Register bit RCR[15] is set (see Section 14.0, "Set Read Configuration Register" on page 89). To perform an asynchronous page mode read, an address is driven onto A[MAX:0], and CE#, OE# and ADV# are asserted. WE# and RST# must be deasserted. WAIT is asserted during asynchronous page mode. ADV# can be driven high to latch the address, or it must be held low throughout the read cycle. CLK is not used for asynchronous page-mode reads, and is ignored. If only asynchronous reads are to be performed, CLK should be tied to a valid VIH level, WAIT signal can be floated and ADV# must be tied to ground. Array data is driven onto DQ[15:0] after an initial access time tAVQV delay. (see Section 7.0, "AC Characteristics" on page 31). In asynchronous page mode, four data words are "sensed" simultaneously from the flash memory array and loaded into an internal page buffer. The buffer word corresponding to the initial address on A[MAX:0] is driven onto DQ[15:0] after the initial access delay. Address bits A[MAX:2] select the 4-word page. Address bits A[1:0] determine which word of the 4-word page is output from the data buffer at any given time. 10.2 Synchronous Burst Read Mode Section 14.0, "Set Read Configuration Register" on page 89continuous wordsTo perform a synchronous burst- read, an initial address is driven onto A[MAX:0], and CE# and OE# are asserted. WE# and RST# must be deasserted. ADV# is asserted, and then deasserted to latch the address. Alternately, ADV# can remain asserted throughout the burst access, in which case the address is latched on the next valid CLK edge after ADV# is asserted. Preliminary Datasheet 65 Intel(R) Wireless Flash Memory (W18) 10.0 Read Operations During synchronous array and non-array read modes, the first word is output from the data buffer on the next valid CLK edge after the initial access latency delay (see Section 14.2, "First Access Latency Count (RCR[13:11])" on page 91). Subsequent data is output on valid CLK edges following a minimum delay. However, for a synchronous non-array read, the same word of data will be output on successive clock edges until the burst length requirements are satisfied. Section 7.0, "AC Characteristics" on page 31 10.3 Read Array The Read Array command places (or resets) the partition in read-array mode and is used to read data from the flash memory array. Upon initial device power-up, or after reset (RST# transitions from VIL to VIH), all partitions default to asynchronous read-array mode. To read array data from the flash device, first write the Read Array command (FFh) to the CUI and specify the desired word address. Then read from that address. If a partition is already in read-array mode, issuing the Read Array command is not required to read from that partition. If the Read Array command is written to a partition that is erasing or programming, the device presents invalid data on the bus until the program or erase operation completes. After the program or erase finishes in that partition, valid array data can then be read. If an Erase Suspend or Program Suspend command suspends the WSM, a subsequent Read Array command places the addressed partition in read-array mode. The Read Array command functions independently of VPP. 10.4 Read Identifier The Read Identifier mode outputs the manufacturer/device identifier, block lock status, protection register codes, and Configuration Register data. The identifier information is contained within a separate memory space on the device and can be accessed along the 4-Mbit partition address range supplied by the Read Identifier command (90h) address. Reads from addresses in Table 24 retrieve ID information. Issuing a Read Identifier command to a partition that is programming or erasing places that partition's outputs in read ID mode while the partition continues to program or erase in the background. Table 24. Device Identification Codes (Sheet 1 of 2) Address1 Item Manufacturer ID Device ID Block Lock Status(2) 66 Data Base Offset Partition 00h Partition Block 0089h Description Intel 8862h 32-Mbit TPD 8863h 32-Mbit BPD 8864h 64-Mbit TPD 8865h 64-Mbit BPD 8866h 128-Mbit TPD 8867h 128-Mbit BPD D0 = 0 Block is unlocked D0 = 1 Block is locked 01h 02h Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 10.0 Read Operations Table 24. Device Identification Codes (Sheet 2 of 2) Address1 Item Block Lock-Down Status(2) Data Base Offset Block 02h Description D1 = 0 Block is not locked-down D1 = 1 Block is locked down Configuration Register Partition 05h Register Data Protection Register Lock Status Partition 80h Lock Data Protection Register Partition 81h - 88h Register Data Multiple reads required to read the entire 128-bit Protection Register. Notes: 1. The address is constructed from a base address plus an offset. For example, to read the Block Lock Status for block number 38 in a BPD, set the address to the BBA (0F8000h) plus the offset (02h), i.e. 0F8002h. Then examine bit 0 of the data to determine if the block is locked. 2. See Section 13.1.4, "Block Lock Status" on page 84 for valid lock status. 10.5 CFI Query This device contains a separate CFI query database that acts as an "on-chip datasheet." The CFI information within this device can be accessed by issuing the Read Query command and supplying a specific address. The address is constructed from the base address of a partition plus a particular offset corresponding to the desired CFI field. Appendix B, "Common Flash Interface (CFI)" on page 101 shows accessible CFI fields and their address offsets. Issuing the Read Query command to a partition that is programming or erasing puts that partition in read query mode while the partition continues to program or erase in the background. 10.6 Read Status Register The device's Status Register displays program and erase operation status. A partition's status can be read after writing the Read Status Register command to any location within the partition's address range. Read-status mode is the default read mode following a Program, Erase, or Lock Block command sequence. Subsequent single reads from that partition will return its status until another valid command is written. The read-status mode supports single synchronous and single asynchronous reads only; it doesn't support burst reads. The first falling edge of OE# or CE# latches and updates Status Register data. The operation doesn't affect other partitions' modes. Because the Status Register is 8 bits wide, only DQ [7:0] contains valid Status Register data; DQ [15:8] contains zeros. See Table 25, "Status Register Definitions" on page 68 and Table 26, "Status Register Descriptions" on page 68. Each 4-Mbit partition contains its own Status Register. Bits SR[6:0] are unique to each partition, but SR[7], the Device WSM Status (DWS) bit, pertains to the entire device. SR[7] provides program and erase status of the entire device. By contrast, the Partition WSM Status (PWS) bit, SR[0], provides program and erase status of the addressed partition only. Status register bits SR[6:1] present information about partition-specific program, erase, suspend, VPP, and block-lock states. Table 27, "Status Register Device WSM and Partition Write Status Description" on page 68 presents descriptions of DWS (SR[7]) and PWS (SR[0]) combinations. Preliminary Datasheet 67 Intel(R) Wireless Flash Memory (W18) 10.0 Read Operations Table 25. Status Register Definitions DWS ESS ES PS VPPS PSS DPS PWS 7 6 5 4 3 2 1 0 Table 26. Bit Status Register Descriptions Name State DWS 7 0 = Device WSM is Busy Device WSM Status ESS 6 0 = Erase in progress/completed Erase Suspend Status 1 = Erase suspended ES 0 = Erase successful 5 Erase Status 1 = Erase error PS 4 0 = Program successful Program Status 1 = VPP low detect, operation aborted VPP Status PSS 0 = Program in progress/completed Program Suspend Status Device Protect Status Partition Write Status Table 27. 1 = Aborted erase/program attempt on locked block 0 = This partition is busy, but only if SR[7]=0 PWS 0 1 = Program suspended 0 = Unlocked DPS 1 1 = Program error 0 = VPP OK VPPS 3 2 1 = Device WSM is Ready 1 = Another partition is busy, but only if SR[7]=0 Description SR[7] indicates erase or program completion in the device. SR[6:1] are invalid while SR[7] = 0. See Table 27 for valid SR[7] and SR[0] combinations. After issuing an Erase Suspend command, the WSM halts and sets SR[7] and SR[6]. SR[6] remains set until the device receives an Erase Resume command. SR[5] is set if an attempted erase failed. A Command Sequence Error is indicated when SR[7,5:4] are set. SR[4] is set if the WSM failed to program a word. The WSM indicates the VPP level after program or erase completes. SR[3] does not provide continuous VPP feedback and isn't guaranteed when VPP VPP1/2. After receiving a Program Suspend command, the WSM halts execution and sets SR[7] and SR[2]. They remain set until a Resume command is received. If an erase or program operation is attempted to a locked block (if WP# = VIL), the WSM sets SR[1] and aborts the operation. Addressed partition is erasing or programming. In EFP mode, SR[0] indicates that a data-stream word has finished programming or verifying depending on the particular EFP phase. See Table 27 for valid SR[7] and SR[0] combinations. Status Register Device WSM and Partition Write Status Description DWS (SR[7]) PWS (SR[0]) 0 0 0 1 1 0 Description The addressed partition is performing a program/erase operation. EFP: device has finished programming or verifying data, or is ready for data. A partition other than the one currently addressed is performing a program/erase operation. EFP: the device is either programming or verifying data. No program/erase operation is in progress in any partition. Erase and Program suspend bits (SR[6,2]) indicate whether other partitions are suspended. EFP: the device has exited EFP mode. 1 68 1 Won't occur in standard program or erase modes. EFP: this combination does not occur. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 10.0 Read Operations 10.7 Clear Status Register The Clear Status Register command clears the Status Register and leaves all partition output states unchanged. The WSM can set all Status Register bits and clear bits SR[7:6,2,0]. Because bits SR[5,4,3,1] indicate various error conditions, they can only be cleared by the Clear Status Register command. By allowing system software to reset these bits, several operations (such as cumulatively programming several addresses or erasing multiple blocks in sequence) can be performed before reading the Status Register to determine error occurrence. If an error is detected, the Status Register must be cleared before beginning another command or sequence. Device reset (RST# = VIL) also clears the Status Register. This command functions independently of VPP. Preliminary Datasheet 69 Intel(R) Wireless Flash Memory (W18) 11.0 Program Operations 11.0 Program Operations 11.1 Word Program When the Word Program command is issued, the WSM executes a sequence of internally timed events to program a word at the desired address and verify that the bits are sufficiently programmed. Programming the flash array changes specifically addressed bits to 0; 1 bits do not change the memory cell contents. Programming can occur in only one partition at a time. All other partitions must be in either a read mode or erase suspend mode. Only one partition can be in erase suspend mode at a time. The Status Register can be examined for program progress by reading any address within the partition that is busy programming. However, while most Status Register bits are partition-specific, the Device WSM Status bit, SR[7], is device-specific; that is, if the Status Register is read from any other partition, SR[7] indicates program status of the entire device. This permits the system CPU to monitor program progress while reading the status of other partitions. CE# or OE# toggle (during polling) updates the Status Register. Several commands can be issued to a partition that is programming: Read Status Register, Program Suspend, Read Identifier, and Read Query. The Read Array command can also be issued, but the read data is indeterminate. After programming completes, three Status Register bits can signify various possible error conditions. SR[4] indicates a program failure if set. If SR[3] is set, the WSM couldn't execute the Word Program command because VPP was outside acceptable limits. If SR[1] is set, the program was aborted because the WSM attempted to program a locked block. After the Status Register data is examined, clear it with the Clear Status Register command before a new command is issued. The partition remains in Status Register mode until another command is written to that partition. Any command can be issued after the Status Register indicates program completion. If CE# is deasserted while the device is programming, the devices will not enter standby mode until the program operation completes. 70 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 11.0 Program Operations Figure 28. Word Program Flowchart WORD PROGRAM PROCEDURE Bus Command Operation Start Write 40h, Word Address Write Program Setup Data = 40h Addr = Location to program (WA) Write Data Data = Data to program (WD) Addr = Location to program (WA) Write Data Word Address Read Suspend Program Loop Read Status Register Standby No SR[7] = 0 Suspend Program Comments Read SRD Toggle CE# or OE# to update SRD Check SR[7] 1 = WSM ready 0 = WSM busy Yes Repeat for subsequent programming operations. 1 Full status register check can be done after each program or after a sequence of program operations. Full Program Status Check (if desired) Program Complete FULL PROGRAM STATUS CHECK PROCEDURE Read Status Register SR[3] = Bus Command Operation 1 SR[4] = Standby Check SR[3] 1 = VPP error Standby Check SR[4] 1 = Data program error Standby Check SR[1] 1 = Attempted program to locked block Program aborted VPP Range Error 0 1 Program Error 1 Device Protect Error Comments 0 SR[1] = 0 Program Successful 11.2 SR[3] MUST be cleared before the WSM will allow further program attempts Only the Clear Staus Register command clears SR[4:3,1]. If an error is detected, clear the status register before attempting a program retry or other error recovery. Factory Programming The standard factory programming mode uses the same commands and algorithm as the Word Program mode (40h/10h). When VPP is at VPP1, program and erase currents are drawn through VCC. If VPP is driven by a logic signal, VPP1 must remain above the VPP1Min value to perform insystem flash modifications. When VPP is connected to a 12 V power supply, the device draws program and erase current directly from VPP. This eliminates the need for an external switching transistor to control the VPP voltage. Figure 37, "Examples of VPP Power Supply Configurations" on page 88 shows examples of flash power supply usage in various configurations. Preliminary Datasheet 71 Intel(R) Wireless Flash Memory (W18) 11.0 Program Operations The 12-V VPP mode enhances programming performance during the short time period typically found in manufacturing processes; however, it is not intended for extended use.12 V may be applied to VPP during program and erase operations as specified in Section , "" on page 26. VPP may be connected to 12 V for a total of tPPH hours maximum. Stressing the device beyond these limits may cause permanent damage. 11.3 Enhanced Factory Program (EFP) EFP substantially improves device programming performance through a number of enhancements to the conventional 12 Volt word program algorithm. EFP's more efficient WSM algorithm eliminates the traditional overhead delays of the conventional word program mode in both the host programming system and the flash device. Changes to the conventional word programming flowchart and internal WSM routine were developed because of today's beat-rate-sensitive manufacturing environments; a balance between programming speed and cycling performance was attained. The host programmer writes data to the device and checks the Status Register to determine when the data has completed programming. This modification essentially cuts write bus cycles in half. Following each internal program pulse, the WSM increments the device's address to the next physical location. Now, programming equipment can sequentially stream program data throughout an entire block without having to setup and present each new address. In combination, these enhancements reduce much of the host programmer overhead, enabling more of a data streaming approach to device programming. EFP further speeds up programming by performing internal code verification. With this, PROM programmers can rely on the device to verify that it has been programmed properly. From the device side, EFP streamlines internal overhead by eliminating the delays previously associated to switch voltages between programming and verify levels at each memory-word location. EFP consists of four phases: setup, program, verify and exit. Refer to Figure 29, "Enhanced Factory Program Flowchart" on page 75 for a detailed graphical representation of how to implement EFP. 11.3.1 EFP Requirements and Considerations Ambient temperature: TA = 25 C 5 C EFP Requirements VCC within specified operating range VPP within specified VPP2 range Target block unlocked Block cycling below 100 erase cycles 1 RWW not supported2 EFP Considerations EFP programs one block at a time EFP cannot be suspended Notes: 1. Recommended for optimum performance. Some degradation in performance may occur if this limit is exceeded, but the internal algorithm will continue to work properly. 2. Code or data cannot be read from another partition during EFP. 72 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 11.0 Program Operations 11.3.2 Setup After receiving the EFP Setup (30h) and EFP Confirm (D0h) command sequence, SR[7] transitions from a 1 to a 0 indicating that the WSM is busy with EFP algorithm startup. A delay before checking SR[7] is required to allow the WSM time to perform all of its setups and checks (VPP level and block lock status). If an error is detected, Status Register bits SR[4], SR[3], and/or SR[1] are set and EFP operation terminates. Note: After the EFP Setup and Confirm command sequence, reads from the device automatically output Status Register data. Do not issue the Read Status Register command; it will be interpreted as data to program at WA0. 11.3.3 Program After setup completion, the host programming system must check SR[0] to determine "data-stream ready" status (SR[0]=0). Each subsequent write after this is a program-data write to the flash array. Each cell within the memory word to be programmed to 0 receives one WSM pulse; additional pulses, if required, occur in the verify phase. SR[0]=1 indicates that the WSM is busy applying the program pulse. The host programmer must poll the device's Status Register for the "program done" state after each data-stream write. SR[0]=0 indicates that the appropriate cell(s) within the accessed memory location have received their single WSM program pulse, and that the device is now ready for the next word. Although the host may check full status for errors at any time, it is only necessary on a block basis, after EFP exit. Addresses must remain within the target block. Supplying an address outside the target block immediately terminates the program phase; the WSM then enters the EFP verify phase. The address can either hold constant or it can increment. The device compares the incoming address to that stored from the setup phase (WA0); if they match, the WSM programs the new data word at the next sequential memory location. If they differ, the WSM jumps to the new address location. The program phase concludes when the host programming system writes to a different block address, and data supplied must be FFFFh. Upon program phase completion, the device enters the EFP verify phase. 11.3.4 Verify A high percentage of the flash bits program on the first WSM pulse. However, for those cells that do not completely program on their first attempt, EFP internal verification identifies them and applies additional pulses as required. The verify phase is identical in flow to the program phase, except that instead of programming incoming data, the WSM compares the verify-stream data to that which was previously programmed into the block. If the data compares correctly, the host programmer proceeds to the next word. If not, the host waits while the WSM applies an additional pulse(s). The host programmer must reset its initial verify-word address to the same starting location supplied during the program phase. It then reissues each data word in the same order as during the program phase. Like programming, the host may write each subsequent data word to WA0 or it may increment up through the block addresses. Preliminary Datasheet 73 Intel(R) Wireless Flash Memory (W18) 11.0 Program Operations The verification phase concludes when the interfacing programmer writes to a different block address; data supplied must be FFFFh. Upon completion of the verify phase, the device enters the EFP exit phase. 11.3.5 Exit SR[7]=1 indicates that the device has returned to normal operating conditions. A full status check should be performed at this time to ensure the entire block programmed successfully. After EFP exit, any valid CUI command can be issued. 74 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 11.0 Program Operations Figure 29. Enhanced Factory Program Flowchart ENHANCED FACTORY PROGRAMMING PROCEDURE EFP Setup EFP Program EFP Verify EFP Exit Start Read Status Register Read Status Register Read Status Register SR[0]=1=N Write 30h Address = WA0 S R [0 ]= 1 = N Write D0h Address = WA0 Read Status Register EFP Setup Done? S R [7 ]= 0 = Y EFP setup time N SR[0]=1=N Verify Stream Ready? Data Stream Ready? Check VPP & Lock errors (SR[3,1]) EFP Exited? SR[0] =0=Y SR[7]=1=Y Write Data Address = WA0 Write Data Address = WA0 Full Status Check Procedure Read Status Register Read Status Register Operation Complete Program Done? Verify Done? SR[0]=0=Y SR[0]=0=Y N Last Data? Last Data? Y SR[7]=1=N SR[7]=0=N SR[0] =0=Y S R [0 ]= 1 = N VPP = 12V Unlock Block Y Write FFFFh Address BBA Write FFFFh Address BBA Exit EFP Setup Bus State Comments Write Unlock Block VPP = 12V Unlock block Write EFP Setup Data = 30h Address = WA0 Write EFP Data = D0h Confirm Address = WA0 Standby Read EFP setup time Status Register EFP Check SR[7] Standby Setup 0 = EFP ready Done? 1 = EFP not ready If SR[7] = 1: Error Check SR[3,1] Standby Condition SR[3] = 1 = VPP error Check SR[1] = 1 = locked block EFP Program Bus State Comments Read Status Register EFP Verify Bus State Comments Read Status Register Data Check SR[0] Standby Stream 0 = Ready for data Ready? 1 = Not ready for data Verify Check SR[0] Standby Stream 0 = Ready for verify Ready? 1 = Not ready for verify Write (note 1) Write (note 2) Data = Data to program Address = WA0 Read Status Register Check SR[0] Program 0 = Program done Standby Done? 1 = Program not done Standby Write Last Data? Device automatically increments address. Exit Data = FFFFh Program Address not within same Phase BBA Data = Word to verify Address = WA0 Read Status Register Standby (note 3) Verify Done? Check SR[0] 0 = Verify done 1 = Verify not done Standby Last Data? Device automatically increments address. Write Exit Verify Phase Data = FFFFh Address not within same BBA EFP Exit 1. WA0 = first Word Address to be programmed within the target block. The BBA (Block Base Read Status Register Address) must remain constant throughout the program phase data stream; WA can be held Check SR[7] constant at the first address location, or it can be written to sequence up through the addresses EFP 0 = Exit not finished Standby within the block. Writing to a BBA not equal to that of the block currently being written to Exited? 1 = Exit completed terminates the EFP program phase, and instructs the device to enter the EFP verify phase. 2. For proper verification to occur, the verify data stream must be presented to the device in the Repeat for subsequent operations. same sequence as that of the program phase data stream. Writing to a BBA not equal to WA After EFP exit, a Full Status Check can terminates the EFP verify phase, and instructs the device to exit EFP . determine if any program error occurred. 3. Bits that did not fully program with the single WSM pulse of the EFP program phase receive additional program-pulse attempts during the EFP verify phase. The device will report any program failure by setting SR[4]=1; this check can be performed during the full status check afterSee the Full Status Check procedure in the Word Program flowchart. EFP has been exited for that block, and will indicate any error within the entire data stream. Preliminary Datasheet 75 Intel(R) Wireless Flash Memory (W18) 12.0 Program and Erase Operations 12.0 Program and Erase Operations 12.1 Program/Erase Suspend and Resume The Program Suspend and Erase Suspend commands halt an in-progress program or erase operation. The command can be issued at any device address. The partition corresponding to the command's address remains in its previous state. A suspend command allows data to be accessed from memory locations other than the one being programmed or the block being erased. A program operation can be suspended only to perform a read operation. An erase operation can be suspended to perform either a program or a read operation within any block, except the block that is erase suspended. A program command nested within a suspended erase can subsequently be suspended to read yet another location. Once a program or erase process starts, the Suspend command requests that the WSM suspend the program or erase sequence at predetermined points in the algorithm. The partition that is actually suspended continues to output Status Register data after the Suspend command is written. An operation is suspended when status bits SR[7] and SR[6] and/or SR[2] are set. To read data from blocks within the partition (other than an erase-suspended block), you can write a Read Array command. Block erase cannot resume until the program operations initiated during erase suspend are complete. Read Array, Read Status Register, Read Identifier (ID), Read Query, and Program Resume are valid commands during Program or Erase Suspend. Additionally, Clear Status Register, Program, Program Suspend, Erase Resume, Lock Block, Unlock Block, and LockDown Block are valid commands during erase suspend. To read data from a block in a partition that is not programming or erasing, the operation does not need to be suspended. If the other partition is already in Read Array, ID, or Query mode, issuing a valid address returns corresponding data. If the other partition is not in a read mode, one of the read commands must be issued to the partition before data can be read. During a suspend, CE# = VIH places the device in standby state, which reduces active current. VPP must remain at its program level and WP# must remain unchanged while in suspend mode. A resume command instructs the WSM to continue programming or erasing and clears Status Register bits SR[2] (or SR[6]) and SR[7]. The Resume command can be written to any partition. When read at the partition that is programming or erasing, the device outputs data corresponding to the partition's last mode. If Status Register error bits are set, the Status Register can be cleared before issuing the next instruction. RST# must remain at VIH. See Figure 30, "Program Suspend / Resume Flowchart" on page 77, and Figure 31, "Erase Suspend / Resume Flowchart" on page 78. If a suspended partition was placed in Read Array, Read Status Register, ID, or Query mode during the suspend, the device remains in that mode and outputs data corresponding to that mode after the program or erase operation is resumed. After resuming a suspended operation, issue the read command appropriate to the read operation. To read status after resuming a suspended operation, issue a Read Status Register command (70h) to return the suspended partition to status mode. 76 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 12.0 Program and Erase Operations Figure 30. Program Suspend / Resume Flowchart PROGRAM SUSPEND / RESUME PROCEDURE Bus Command Operation Start Program Suspend Write Write B0h Any Address Read Write Status Write 70h Same Partition SR.7 = Program Data = B0h Suspend Addr = Block to suspend (BA) Read Status 0 Standby Check SR.7 1 = WSM ready 0 = WSM busy Standby Check SR.2 1 = Program suspended 0 = Program completed 1 SR.2 = 0 Program Completed 1 Read Write Array Write FFh Susp Partition Read Array Done Reading Yes Program Resume Write Write Read Array Write FFh Pgm'd Partition Program Resumed Read Array Data Read Status Return partition to Status mode: Data = 70h Addr = Same partition Status Write 70h Same Partition Preliminary Datasheet Program Data = D0h Resume Addr = Suspended block (BA) If the suspended partition was placed in Read Array mode: No Write D0h Any Address Read Data = FFh Addr = Any address within the suspended partition Read array data from block other than the one being programmed Read Read Array Data Data = 70h Addr = Same partition Status register data Toggle CE# or OE# to update Status register Addr = Suspended block (BA) Read Read Status Register Comments PGM_SUS.WMF 77 Intel(R) Wireless Flash Memory (W18) 12.0 Program and Erase Operations Figure 31. Erase Suspend / Resume Flowchart ERASE SUSPEND / RESUME PROCEDURE Bus Command Operation Start Erase Suspend Write B0h Any Address Read Status Write Erase Suspend Write Read Status Write 70h Same Partition Read Status Register Read or Program? Read Array Data Standby Check SR.6 1 = Erase suspended 0 = Erase completed Write 1 Read Check SR.7 1 = WSM ready 0 = WSM busy Erase Completed 0 SR.6 = No Program Loop Write Yes Resume Array Write FFh Erased Partition Erase Resumed Read Array Data Program Resume Data = D0h Addr = Any address Write Read Status Return partition to Status mode: Data = 70h Addr = Same partition Status Write 70h Same Partition 12.2 Read Write D0h Any Address Read Read array or program data from/to block other than the one being erased If the suspended partition was placed in Read Array mode or a Program Loop: Done? Erase Read Array Data = FFh or 40h or Program Addr = Block to program or read Read or Write Program Data = 70h Addr = Same partition Standby 0 1 Data = B0h Addr = Any address Status register data. Toggle CE# or OE# to update Status register Addr = Same partition Read SR.7 = Comments ERAS_SUS.WMF Block Erase The 2-cycle block erase command sequence, consisting of Erase Setup (20h) and Erase Confirm (D0h), initiates one block erase at the addressed block. Only one partition can be in an erase mode at a time; other partitions must be in a read mode. The Erase Confirm command internally latches the address of the block to be erased. Erase forces all bits within the block to 1. SR[7] is cleared while the erase executes. 78 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 12.0 Program and Erase Operations After writing the Erase Confirm command, the selected partition is placed in read Status Register mode and reads performed to that partition return the current status data. The address given during the Erase Confirm command does not need to be the same address used in the Erase Setup command. So, if the Erase Confirm command is given to partition B, then the selected block in partition B will be erased even if the Erase Setup command was to partition A. The 2-cycle erase sequence cannot be interrupted with a bus write operation. For example, an Erase Setup command must be immediately followed by the Erase Confirm command in order to execute properly. If a different command is issued between the setup and confirm commands, the partition is placed in read-status mode, the Status Register signals a command sequence error, and all subsequent erase commands to that partition are ignored until the Status Register is cleared. The CPU can detect block erase completion by analyzing SR[7] of that partition. If an error bit (SR[5,3,1]) was flagged, the Status Register can be cleared by issuing the Clear Status Register command before attempting the next operation. The partition remains in read-status mode until another command is written to its CUI. Any CUI instruction can follow after erasing completes. The CUI can be set to read-array mode to prevent inadvertent Status Register reads. Preliminary Datasheet 79 Intel(R) Wireless Flash Memory (W18) 12.0 Program and Erase Operations Figure 32. Block Erase Flowchart BLOCK ERASE PROCEDURE Bus Command Comments Operation Block Data = 20h Write Erase Addr = Block to be erased (BA) Setup Start Write 20h Block Address Write Write D0h and Block Address Erase Confirm Read Suspend Erase Loop Read Status Register No SR[7] = 0 Suspend Erase Standby Data = D0h Addr = Block to be erased (BA) Read SRD Toggle CE# or OE# to update SRD Check SR[7] 1 = WSM ready 0 = WSM busy Yes Repeat for subsequent block erasures. 1 Full status register check can be done after each block erase or after a sequence of block erasures. Full Erase Status Check (if desired) Block Erase Complete FULL ERASE STATUS CHECK PROCEDURE Read Status Register SR[3] = Bus Command Operation 1 SR[5:4] = Standby Standby Check SR[5:4] Both 1 = Command sequence error Standby Check SR[5] 1 = Block erase error Standby Check SR[1] 1 = Attempted erase of locked block Erase aborted VPP Range Error 0 1 Command Sequence Error 1 Block Erase Error Comments Check SR[3] 1 = VPP error 0 SR[5] = 0 SR[1] = 0 Block Erase Successful 12.3 1 Erase of Locked Block Aborted SR[3,1] must be cleared before the WSM will allow further erase attempts. Only the Clear Status Register command clears SR[5:3,1]. If an error is detected, clear the Status register before attempting an erase retry or other error recovery. Read-While-Write and Read-While-Erase The Intel(R) Wireless Flash Memory (W18) supports flexible multi-partition dual-operation architecture. By dividing the flash memory into many separate partitions, the device can read from one partition while programing or erasing in another partition; hence the terms, RWW and RWE. Both of these features greatly enhance data storage performance. 80 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 12.0 Program and Erase Operations The product does not support simultaneous program and erase operations. Attempting to perform operations such as these results in a command sequence error. Only one partition can be programming or erasing while another partition is reading. However, one partition may be in erase suspend mode while a second partition is performing a program operation, and yet another partition is executing a read command. Table 22, "Command Codes and Descriptions" on page 61 describes the command codes available for all functions. Preliminary Datasheet 81 Intel(R) Wireless Flash Memory (W18) 13.0 Security Modes 13.0 Security Modes The Intel Wireless Flash Memory offers both hardware and software security features to protect the flash data. The software security feature is used by executing the Lock Block command. The hardware security feature is used by executing the Lock-Down Block command and by asserting the WP# signal. Refer to Figure 33, "Block Locking State Diagram" on page 83 for a state diagram of the flash security features. Also see Figure 34, "Locking Operations Flowchart" on page 85. 13.1 Block Lock Operations Individual instant block locking protects code and data by allowing any block to be locked or unlocked with no latency. This locking scheme offers two levels of protection. The first allows software-only control of block locking (useful for frequently changed data blocks), while the second requires hardware interaction before locking can be changed (protects infrequently changed code blocks). The following sections discuss the locking system operation. The term "state [abc]" specifies locking states; for example, "state [001]," where a = WP# value, b = block lock-down status bit D1, and c = Block Lock Status Register bit D0. Figure 33, "Block Locking State Diagram" on page 83 defines possible locking states. The following summarizes the locking functionality. * All blocks power-up in a locked state. * Unlock commands can unlock these blocks, and lock commands can lock them again. * The Lock-Down command locks a block and prevents it from being unlocked when WP# is asserted. -- Locked-down blocks can be unlocked or locked with commands as long as WP# is deasserted. -- The lock-down status bit is cleared only when the device is reset or powered-down. Block lock registers are not affected by the VPP level. They may be modified and read even if VPP VPPLK. Each block's locking status can be set to locked, unlocked, and lock-down, as described in the following sections. See Figure 34, "Locking Operations Flowchart" on page 85. 82 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 13.0 Security Modes Figure 33. Block Locking State Diagram Power-Up/Reset Locked [X01] LockedDown4,5 [011] Hardware Locked5 [011] WP# Hardware Control Unlocked [X00] Software Locked [111] Unlocked [110] Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0) Software Block Lock-Down (0x60/0x2F) WP# hardware control Notes: 13.1.1 1. [a,b,c] represents [WP#, D1, D0]. X = Don't Care. 2. D1 indicates block Lock-down status. D1 = `0', Lock-down has not been issued to this block. D1 = `1', Lock-down has been issued to this block. 3. D0 indicates block lock status. D0 = `0', block is unlocked. D0 = `1', block is locked. 4. Locked-down = Hardware + Software locked. 5. [011] states should be tracked by system software to determine difference between Hardware Locked and Locked-Down states. Lock All blocks default to locked (state [x01]) after initial power-up or reset. Locked blocks are fully protected from alteration. Attempted program or erase operations to a locked block will return an error in SR[1]. Unlocked blocks can be locked by using the Lock Block command sequence. Similarly, a locked block's status can be changed to unlocked or lock-down using the appropriate software commands. 13.1.2 Unlock Unlocked blocks (states [x00] and [110]) can be programmed or erased. All unlocked blocks return to the locked state when the device is reset or powered-down. An unlocked block's status can be changed to the locked or locked-down state using the appropriate software commands. A locked block can be unlocked by writing the Unlock Block command sequence if the block is not lockeddown. 13.1.3 Lock-Down Locked-down blocks (state [011]) offer the user an additional level of write protection beyond that of a regular locked block. A block that is locked-down cannot have it's state changed by software if WP# is asserted. A locked or unlocked block can be locked-down by writing the Lock-Down Block command sequence. If a block was set to locked-down, then later changed to unlocked, a Lock- Preliminary Datasheet 83 Intel(R) Wireless Flash Memory (W18) 13.0 Security Modes Down command should be issued prior asserting WP# will put that block back to the locked-down state. When WP# is deasserted, locked-down blocks are changed to the locked state and can then be unlocked by the Unlock Block command. 13.1.4 Block Lock Status Every block's lock status can be read in read identifier mode. To enter this mode, issue the Read Identifier command to the device. Subsequent reads at BBA + 02h will output that block's lock status. For example, to read the block lock status of block 10, the address sent to the device should be 50002h (for a top-parameter device). The lowest two data bits of the read data, DQ1 and DQ0, represent the lock status. DQ0 indicates the block lock status. It is set by the Lock Block command and cleared by the Block Unlock command. It is also set when entering the lock-down state. DQ1 indicates lock-down status and is set by the Lock-Down command. The lock-down status bit cannot be cleared by software-only by device reset or power-down. See Table 28. Table 28. 13.1.5 Write Protection Truth Table VPP WP# RST# Write Protection X X VIL Device inaccessible VIL X VIH Word program and block erase prohibited X VIL VIH All lock-down blocks locked X VIH VIH All lock-down blocks can be unlocked Lock During Erase Suspend Block lock configurations can be performed during an erase suspend operation by using the standard locking command sequences to unlock, lock, or lock-down a block. This feature is useful when another block requires immediate updating. To change block locking during an erase operation, first write the Erase Suspend command. After checking SR[6] to determine the erase operation has suspended, write the desired lock command sequence to a block; the lock status will be changed. After completing lock, unlock, read, or program operations, resume the erase operation with the Erase Resume command (D0h). If a block is locked or locked-down during a suspended erase of the same block, the locking status bits change immediately. When the erase operation is resumed, it will complete normally. Locking operations cannot occur during program suspend. Appendix A, "Write State Machine States" on page 98 shows valid commands during erase suspend. 13.1.6 Status Register Error Checking Using nested locking or program command sequences during erase suspend can introduce ambiguity into Status Register results. Because locking changes require 2-cycle command sequences, for example, 60h followed by 01h to lock a block, following the Configuration Setup command (60h) with an invalid command produces a command sequence error (SR[5:4]=11b). If a Lock Block command error occurs during erase suspend, the device sets SR[4] and SR[5] to 1 even after the erase is resumed. When erase is 84 Preliminary Datasheet complete, possible errors during the erase cannot be detected from the Status Register because of the previous locking command error. A similar situation occurs if a program operation error is nested within an erase suspend. 13.1.7 WP# Lock-Down Control The Write Protect signal, WP#, adds an additional layer of block security. WP# only affects blocks that once had the Lock-Down command written to them. After the lock-down status bit is set for a block, asserting WP# forces that block into the lock-down state [011] and prevents it from being unlocked. After WP# is deasserted, the block's state reverts to locked [111] and software commands can then unlock the block (for erase or program operations) and subsequently re-lock it. Only device reset or power-down can clear the lock-down status bit and render WP# ineffective. Figure 34. Locking Operations Flowchart LOCKING OPERATIONS PROCEDURE Start Bus Command Operation Write 60h Block Address Write Write 01,D0,2Fh Block Address Write Optional Write 90h BBA + 02h Write (Optional) Read Block Lock Status Locking Change? Lock Setup Comments Data = 60h Addr = Block to lock/unlock/lock-down (BA) Lock, Data = 01h (Lock block) Unlock, or D0h (Unlock block) Lockdown 2Fh (Lockdown block) Confirm Addr = Block to lock/unlock/lock-down (BA) Read ID Plane Data = 90h Addr = BBA + 02h Read Block Lock Block Lock status data (Optional) Status Addr = BBA + 02h No Confirm locking change on DQ[1:0]. (See Block Locking State Transitions Table for valid combinations.) Standby (Optional) Yes Write FFh Partition Address Write Read Array Data = FFh Addr = Any address in same partition Lock Change Complete 13.2 Protection Register The Intel Wireless Flash Memory includes a 128-bit Protection Register. This protection register is used to increase system security and for identification purposes. The protection register value can match the flash component to the system's CPU or ASIC to prevent device substitution. The lower 64 bits within the protection register are programmed by Intel with a unique number in each flash device. The upper 64 OTP bits within the protection register are left for the customer to program. Once programmed, the customer segment can be locked to prevent further programming. Intel(R) Wireless Flash Memory (W18) 13.0 Security Modes Note: The individual bits of the user segment of the protection register are OTP, not the register in total. The user may program each OTP bit individually, one at a time, if desired. After the protection register is locked, however, the entire user segment is locked and no more user bits can be programmed. The protection register shares some of the same internal flash resources as the parameter partition. Therefore, RWW is only allowed between the protection register and main partitions. Table 29 describes the operations allowed in the protection register, parameter partition, and main partition during RWW and RWE. Table 29. Simultaneous Operations Allowed with the Protection Register Protection Register Parameter Partition Array Data Main Partitions Description Read See Description Write/Erase While programming or erasing in a main partition, the protection register can be read from any other partition. Reading the parameter partition data is not allowed if the protection register is being read from addresses within the parameter partition. See Description Read Write/Erase While programming or erasing in a main partition, read operations are allowed in the parameter partition. Accessing the protection registers from parameter partition addresses is not allowed. Read Read Write/Erase While programming or erasing in a main partition, read operations are allowed in the parameter partition. Accessing the protection registers in a partition that is different from the one being programmed or erased, and also different from the parameter partition, is allowed. Write No Access Allowed Read While programming the protection register, reads are only allowed in the other main partitions. Access to the parameter partition is not allowed. This is because programming of the protection register can only occur in the parameter partition, so it will exist in status mode. No Access Allowed Write/Erase Read While programming or erasing the parameter partition, reads of the protection registers are not allowed in any partition. Reads in other main partitions are supported. 13.2.1 Reading the Protection Register Writing the Read Identifier command allows the protection register data to be read 16 bits at a time from addresses shown in Table 24, "Device Identification Codes" on page 66. The protection register is read from the Read Identifier command and can be read in any partition.Writing the Read Array command returns the device to read-array mode. 13.2.2 Programing the Protection Register The Protection Program command should be issued only at the parameter (top or bottom) partition followed by the data to be programmed at the specified location. It programs the upper 64 bits of the protection register 16 bits at a time. Table 24, "Device Identification Codes" on page 66 shows allowable addresses. See also Figure 35, "Protection Register Programming Flowchart" on page 87. Issuing a Protection Program command outside the register's address space results in a Status Register error (SR[4]=1). 86 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 13.0 Security Modes 13.2.3 Locking the Protection Register PR-LK.0 is programmed to 0 by Intel to protect the unique device number. PR-LK.1 can be programmed by the user to lock the user portion (upper 64 bits) of the protection register (See Figure 36, "Protection Register Locking"). This bit is set using the Protection Program command to program "FFFDh" into PR-LK. After PR-LK register bits are programmed (locked), the protection register's stored values can't be changed. Protection Program commands written to a locked section result in a Status Register error (SR[4]=1, SR[5]=1). Figure 35. Protection Register Programming Flowchart PROTECTION REGISTER PROGRAMMINGPROCEDURE Bus Command Comments Operation Protection Data = C0h Write Program Addr = Protection address Setup Start Write C0h Addr=Prot addr Write Write Protect. Register Address / Data Read Read Status Register Standby SR[7] = 1? No Protection Data = Data to program Program Addr = Protection address Read SRD Toggle CE# or OE# to update SRD Check SR[7] 1 = WSM Ready 0 = WSM Busy Protection Program operations addresses must be within the protection register address space. Addresses outside this space will return an error. Yes Repeat for subsequent programming operations. Full Status Check (if desired) Full status register check can be done after each program or after a sequence of program operations. Program Complete FULL STATUS CHECK PROCEDURE Bus Command Operation Read SRD Standby SR[4:3] = 1,1 SR[4,1] = Program Successful Preliminary Datasheet 1,0 1,1 SR[1] SR[3] SR[4] 0 1 1 VPP Error VPP Range Error Standby SR[4,1] = Comments Programming Error Locked-Register Program Aborted Standby 0 0 1 Protection register program error 1 0 1 Register locked; Operation aborted SR[3] MUST be cleared before the WSM will allow further program attempts. Only the Clear Staus Register command clears SR[4:3,1]. If an error is detected, clear the status register before attempting a program retry or other error recovery. 87 Intel(R) Wireless Flash Memory (W18) 13.0 Security Modes Figure 36. Protection Register Locking 0x88 User-Programmable 0x85 0x84 Intel Factory-Programmed 0x81 PR Lock Register 0 0x80 13.3 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 VPP Protection The Intel(R) Wireless Flash Memory (W18) provides in-system program and erase at VPP1. For factory programming, it also includes a low-cost, backward-compatible 12 V programming feature.(See "Factory Programming" on page 71.) The EFP feature can also be used to greatly improve factory program performance as explained in Section 11.3, "Enhanced Factory Program (EFP)" on page 72. In addition to the flexible block locking, holding the VPP programming voltage low can provide absolute hardware write protection of all flash-device blocks. If VPP is below VPPLK, program or erase operations result in an error displayed in SR[3]. (See Figure 37.) Figure 37. Examples of VPP Power Supply Configurations System supply 12 V supply VCC VPP System supply VCC Prot# (logic signal) VPP 10K * 12 V fast programming * Absolute write protection with VPP VPPLK System supply VCC * Low-voltage programming * Absolute write protection via logic signal System supply VCC (Note 1) 12 V supply VPP * Low voltage and 12 V fast programming Note: 88 VPP * Low-voltage programming If the VCC supply can sink adequate current, you can use an appropriately valued resistor. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register 14.0 Set Read Configuration Register The Set Read Configuration Register (RCR) command sets the burst order, frequency configuration, burst length, and other parameters. A two-bus cycle command sequence initiates this operation. The Read Configuration Register data is placed on the lower 16 bits of the address bus (A[15:0]) during both bus cycles. The Set Read Configuration Register command is written along with the configuration data (on the address bus). This is followed by a second write that confirms the operation and again presents the Read Configuration Register data on the address bus. The Read Configuration Register data is latched on the rising edge of ADV#, CE#, or WE# (whichever occurs first). This command functions independently of the applied VPP voltage. After executing this command, the device returns to read-array mode. The Read Configuration Register's contents can be examined by writing the Read Identifier command and then reading location 05h. See Table 30 and Table 31. Table 31. Res'd WAIT Polarity Data Output Config WAIT Config Burst Seq Clock Config Res'd Res'd Burst Wrap Read Configuration Register Summary Read Mode Table 30. RM R LC2 LC1 LC0 WT DOC WC BS CC R R BW BL2 BL1 BL0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 First Access Latency Count Burst Length Read Configuration Register Descriptions (Sheet 1 of 2) Bit Name 15 RM Read Mode 14 R 13-11 First Access Latency Count LC[2:0] 10 WT WAIT Signal Polarity DOC 9 8 7 Data Output Configuration WC WAIT Configuration BS Burst Sequence CC 6 Preliminary Datasheet Clock Configuration Description1 Notes 0 = Synchronous Burst Reads Enabled 1 = Asynchronous Reads Enabled (Default) 2 Reserved 5 001 = Reserved 010 = Code 2 011 = Code 3 100 = Code 4 101 = Code 5 111 = Reserved (Default) 6 0 = WAIT signal is asserted low 1 = WAIT signal is asserted high (Default) 3 0 = Hold Data for One Clock 1 = Hold Data for Two Clock (Default) 6 0 = WAIT Asserted During Delay 1 = WAIT Asserted One Data Cycle before Delay (Default) 6 1 = Linear Burst Order (Default) 0 = Burst Starts and Data Output on Falling Clock Edge 1 = Burst Starts and Data Output on Rising Clock Edge (Default) 89 Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register Table 31. Read Configuration Register Descriptions (Sheet 2 of 2) Description1 Bit Name Notes 5 R Reserved 5 4 R Reserved 5 3 BW Burst Wrap 2-0 BL[2:0] Burst Length 0 = Wrap bursts within burst length set by CR[2:0] 1 = Don't wrap accesses within burst length set by CR[2:0].(Default) 001 = 4-Word Burst 010 = 8-Word Burst 011 = 16-Word Burst 111 = Continuous Burst (Default) 4 Notes: 1. Undocumented combinations of bits are reserved by Intel for future implementations. 2. Synchronous and page read mode configurations affect reads from main blocks and parameter blocks. Status Register and configuration reads support single read cycles. RCR[15]=1 disables configuration set by RCR[14:0]. 3. Data is not ready when WAIT is asserted. 4. Set the synchronous burst length. In asynchronous page mode, the page size equals four words. 5. Set all reserved Read Configuration Register bits to zero. 6. Setting the Read Configuration Register for synchronous burst-mode with a latency count of 2 (RCR[13:11] = 010), data hold for 2 clocks (RCR[9] = 1), and WAIT asserted one data cycle before delay (RCR[8] =1) is not supported. 90 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register 14.1 Read Mode (RCR[15]) All partitions support two high-performance read configurations: synchronous burst mode and asynchronous page mode (default). RCR[15] sets the read configuration to one of these modes. Status register, query, and identifier modes support only asynchronous and single-synchronous read operations. 14.2 First Access Latency Count (RCR[13:11]) The First Access Latency Count (RCR[13:11]) configuration tells the device how many clocks must elapse from ADV# de-assertion (VIH) before the first data word should be driven onto its data pins. The input clock frequency determines this value. See Table 31, "Read Configuration Register Descriptions" on page 89 for latency values. Figure 38 shows data output latency from ADV# assertion for different latencies. Refer to Section 14.2.1, "Latency Count Settings" on page 92 for Latency Code Settings. Figure 38. First Access Latency Configuration CLK [C] Valid Address Address [A] ADV# [V] Code 2 D[15:0] [Q] Valid Output Code 3 D[15:0] [Q] Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Valid Output Code 4 D[15:0] [Q] Valid Output Code 5 D[15:0] [Q] Note: Other First Access Latency Configuration settings are reserved. ) Figure 39. Word Boundary Word 0 - 3 0 1 2 Word 4 - 7 3 4 5 6 Word 8 - B 7 8 9 Word C - F A B C D E F 16 Word Boundary 4 Word Boundary Preliminary Datasheet 91 Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register Note: The 16-word boundary is the end of the device sense word-line. 14.2.1 Latency Count Settings Table 32. Latency Count Setting for VCCQ = 1.7 V - 1.95 V (90 nm lithography) VCCQ = 1.7 - 1.95 V Unit tAVQV/tCHQV (60ns/11ns) Latency Count Settings 2 3 4, 5 Frequency Support < 40 < 61 < 66 Table 33. MHz Latency Count Setting for VCCQ = 1.7 V - 2.24 V (130 nm lithography) VCCQ = 1.7 - 2.24 V Unit tAVQV/tCHQV (60ns/11ns) tAVQV/tCHQV (80ns/14ns) Latency Count Settings 2 3 4, 5 2 3 4, 5 Frequency Support < 40 < 61 < 66 < 30 < 45 < 54 Table 34. MHz Latency Count Settings for VCCQ = 1.35 V - 1.8 V (130 nm lithography) VCCQ = 1.35 V - 1.8 V Unit tAVQV/tCHQV (65ns/14ns) tAVQV/tCHQV (85ns/20ns) Latency Count Settings 2 3, 4, 5 2 3, 4, 5 Frequency Support < 39 < 54 < 30 < 40 Table 35. MHz Latency Count Setting for VCCQ = 1.7 V - 2.24 V (180 nm lithography) VCCQ = 1.7 - 2.24 V Unit tAVQV/tCHQV (70ns/14ns) 92 tAVQV/tCHQV (85ns/18ns) Latency Count Settings 2 3, 4, 5 2 3, 4, 5 Frequency Support < 35 <52 < 29 < 40 MHz Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register Figure 40. Example: Latency Count Setting at 3 tADD-DELAY CLK (C) 0st tDATA 2rd 1nd 3th 4th CE# (E) ADV# (V) AMAX-0 (A) Valid Address Code 3 DQ15-0 (D/Q) High Z Valid Output Valid Output R103 14.3 WAIT Signal Polarity (RCR[10]) If the WAIT bit is cleared (RCR[10]=0), then WAIT is configured to be asserted low. This means that a 0 on the WAIT signal indicates that data is not ready and the data bus contains invalid data. Conversely, if RCR[10] is set, then WAIT is asserted high. In either case, if WAIT is deasserted, then data is ready and valid. WAIT is asserted during asynchronous page mode reads. 14.4 WAIT Signal Function The WAIT signal indicates data valid when the device is operating in synchronous mode (RCR[15]=0), and when addressing a partition that is currently in read-array mode. The WAIT signal is only "deasserted" when data is valid on the bus. When the device is operating in synchronous non-read-array mode, such as read status, read ID, or read query, WAIT is set to an "asserted" state as determined by RCR[10]. See Figure 14, "WAIT Signal in Synchronous Non-Read Array Operation Waveform" on page 43. When the device is operating in asynchronous page mode or asynchronous single word read mode, WAIT is set to an "asserted" state as determined by RCR[10]. See Figure 10, "Page-Mode Read Operation Waveform" on page 39, and Figure 8, "Asynchronous Read Operation Waveform" on page 37. From a system perspective, the WAIT signal is in the asserted state (based on RCR[10]) when the device is operating in synchronous non-read-array mode (such as Read ID, Read Query, or Read Status), or if the device is operating in asynchronous mode (RCR[15]=1). In these cases, the system software should ignore (mask) the WAIT signal, because it does not convey any useful information about the validity of what is appearing on the data bus. Preliminary Datasheet 93 Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register Table 36. WAIT Signal Conditions CONDITION 14.5 WAIT CE# = VIH CE# = VIL Tri-State Active OE# No-Effect Synchronous Array Read Active Synchronous Non-Array Read Asserted All Asynchronous Read and all Write Asserted Data Hold (RCR[9]) The Data Output Configuration (DOC) bit (RCR[9]) determines whether a data word remains valid on the data bus for one or two clock cycles. The processor's minimum data set-up time and the flash memory's clock-to-data output delay determine whether one or two clocks are needed. A DOC set at 1-clock data hold corresponds to a 1-clock data cycle; a DOC set at 2-clock data hold corresponds to a 2-clock data cycle. The setting of this configuration bit depends on the system and CPU characteristics. For clarification, see Figure 41, "Data Output Configuration with WAIT Signal Delay" on page 95. A method for determining this configuration setting is shown below. To set the device at 1-clock data hold for subsequent reads, the following condition must be satisfied: tCHQV (ns) + t DATA (ns) One CLK Period (ns) As an example, use a clock frequency of 66 MHz and a clock period of 15 ns. Assume the data output hold time is one clock. Apply this data to the formula above for the subsequent reads: 11 ns + 4 ns 15 ns This equation is satisfied, and data output will be available and valid at every clock period. If tDATA is long, hold for two cycles. During page-mode reads, the initial access time can be determined by the formula: tADD-DELAY (ns) + tDATA (ns) + t AVQV (ns) Subsequent reads in page mode are defined by: tAPA (ns) + tDATA (ns) 94 (minimum time) Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register Figure 41. Data Output Configuration with WAIT Signal Delay CLK [C] WAIT (CR.8 = 1) Note 1 tCHQV WAIT (CR.8 = 0) 1 CLK Data Hold Note 1 Valid Output DQ15-0 [Q] WAIT (CR.8 = 0) 2 CLK Data Hold DQ15-0 [Q] Note: 14.6 Valid Output Note 1 tCHTL/H WAIT (CR.8 = 1) Valid Output tCHQV Note 1 Valid Output Valid Output WAIT shown asserted high (RCR[10]=1). WAIT Delay (RCR[8]) The WAIT configuration bit (RCR[8]) controls WAIT signal delay behavior for all synchronous read-array modes. Its setting depends on the system and CPU characteristics. The WAIT can be asserted either during, or one data cycle before, a valid output. In synchronous linear read array (no-wrap mode RCR[3]=1) of 4-, 8-, 16-, or continuous-word burst mode, an output delay may occur when a burst sequence crosses its first device-row boundary (16-word boundary). If the burst start address is 4-word boundary aligned, the delay does not occur. If the start address is misaligned to a 4-word boundary, the delay occurs once per burst-mode read sequence. The WAIT signal informs the system of this delay. 14.7 Burst Sequence (RCR[7]) The burst sequence specifies the synchronous-burst mode data order (see Table 37, "Sequence and Burst Length" on page 96). When operating in a linear burst mode, either 4-, 8-, or 16-word burst length with the burst wrap bit (RCR[3]) set, or in continuous burst mode, the device may incur an output delay when the burst sequence crosses the first 16-word boundary. (See Figure 39, "Word Boundary" on page 91 for word boundary description.) This depends on the starting address. If the starting address is aligned to a 4-word boundary, there is no delay. If the starting address is the end of a 4-word boundary, the output delay is one clock cycle less than the First Access Latency Count; this is the worst-case delay. The delay takes place only once, and only if the burst sequence crosses a 16-word boundary. The WAIT pin informs the system of this delay. For timing diagrams of WAIT functionality, see these figures: * Figure 11, "Single Synchronous Read-Array Operation Waveform" on page 40 * Figure 12, "Synchronous 4-Word Burst Read Operation Waveform" on page 41 Preliminary Datasheet 95 Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register * Figure 13, "WAIT Functionality for EOWL (End-of-Word Line) Condition Waveform" on page 42 Sequence and Burst Length 4-Word Burst 8-Word Burst 16-Word Burst Continuous Burst RCR[2:0]=001b RCR[2:0]=010b RCR[2:0]=011b RCR[2:0]=111b Linear Linear Linear Linear 0 0-1-2-3 0-1-2-3-4-5-6-7 0-1-2...14-15 0-1-2-3-4-5-6-... 1 1-2-3-0 1-2-3-4-5-6-7-0 1-2-3...14-15-0 1-2-3-4-5-6-7-... 2 2-3-0-1 2-3-4-5-6-7-0-1 2-3-4...15-0-1 2-3-4-5-6-7-8-... 3 3-0-1-2 3-4-5-6-7-0-1-2 3-4-5...15-0-1-2 3-4-5-6-7-8-9-... 4 4-5-6-7-0-1-2-3 4-5-6...15-0-1-2-3 4-5-6-7-8-9-10... 5 5-6-7-0-1-2-3-4 5-6-7...15-0-1...4 5-6-7-8-9-10-11... 6 6-7-0-1-2-3-4-5 6-7-8...15-0-1...5 6-7-8-9-10-11-12-... 7 7-0-1-2-3-4-5-6 7-8-9...15-0-1...6 7-8-9-10-11-12-13... ... 14-15-16-17-18-19-20-... 15-16-17-18-19-... 0 0-1-2-3 0-1-2-3-4-5-6-7 0-1-2...14-15 0-1-2-3-4-5-6-... 1 1-2-3-4 1-2-3-4-5-6-7-8 1-2-3...15-16 1-2-3-4-5-6-7-... 2 2-3-4-5 2-3-4-5-6-7-8-9 2-3-4...16-17 2-3-4-5-6-7-8-... 3 3-4-5-6 3-4-5-6-7-8-9-10 3-4-5...17-18 3-4-5-6-7-8-9-... 4 4-5-6-7-8-9-10-11 4-5-6...18-19 4-5-6-7-8-9-10... 5 5-6-7-8-9-10-11-12 5-6-7...19-20 5-6-7-8-9-10-11... 6 6-7-8-9-10-11-12-13 6-7-8...20-21 6-7-8-9-10-11-12-... 7 7-8-9-10-11-12-13-14 7-8-9...21-22 7-8-9-10-11-12-13... ... 14-15-16-17-18-19-20-... 15 15-16...29-30 15-16-17-18-19-20-21-... ... 14-15...28-29 ... 14 ... ... No-Wrap (RCR[3]=1) ... 14-15-0-1...13 15-0-1-2-3...14 ... 14 15 ... 14.8 Burst Addressing Sequence (Decimal) ... Wrap (RCR[3]=0) Start Addr. (Dec) Table 37. Clock Edge (RCR[6]) Configuring the valid clock edge enables a flexible memory interface to a wide range of burst CPUs. Clock configuration sets the device to start a burst cycle, output data, and assert WAIT on the clock's rising or falling edge. 96 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) 14.0 Set Read Configuration Register 14.9 Burst Wrap (RCR[3]) The burst wrap bit determines whether 4-, 8-, or 16-word burst accesses wrap within the burstlength boundary or whether they cross word-length boundaries to perform linear accesses. Nowrap mode (RCR[3]=1) enables WAIT to hold off the system processor, as it does in the continuous burst mode, until valid data is available. In no-wrap mode (RCR[3]=0), the device operates similarly to continuous linear burst mode but consumes less power during 4-, 8-, or 16word bursts. For example, if RCR[3]=0 (wrap mode) and RCR[2:0] = 1h (4-word burst), possible linear burst sequences are 0-1-2-3, 1-2-3-0, 2-3-0-1, 3-0-1-2. If RCR[3]=1 (no-wrap mode) and RCR[2:0] = 1h (4-word burst length), then possible linear burst sequences are 0-1-2-3, 1-2-3-4, 2-3-4-5, and 3-4-5-6. RCR[3]=1 not only enables limited nonaligned sequential bursts, but also reduces power by minimizing the number of internal read operations. Setting RCR[2:0] bits for continuous linear burst mode (7h) also achieves the above 4-word burst sequences. However, significantly more power may be consumed. The 1-2-3-4 sequence, for example, consumes power during the initial access, again during the internal pipeline lookup as the processor reads word 2, and possibly again, depending on system timing, near the end of the sequence as the device pipelines the next 4-word sequence. RCR[3]=1 while in 4-word burst mode (no-wrap mode) reduces this excess power consumption. 14.10 Burst Length (RCR[2:0]) The Burst Length bit (BL[2:0]) selects the number of words the device outputs in synchronous read access of the flash memory array. The burst lengths are 4-word, 8-word, 16-word, and continuous word. Continuous-burst accesses are linear only, and do not wrap within any word length boundaries (see Table 37, "Sequence and Burst Length" on page 96). When a burst cycle begins, the device outputs synchronous burst data until it reaches the end of the "burstable" address space. Preliminary Datasheet 97 Intel(R) Wireless Flash Memory (W18) Appendix A Write State Machine States Appendix A Write State Machine States This table shows the command state transitions based on incoming commands. Only one partition can be actively programming or erasing at a time. Figure 42. Write State Machine -- Next State Table (Sheet 1 of 2) W r it e S t a t e M a c h i n e ( W S M ) N e x t S t a t e T a b l e C h i p N e x t S ta te a ft e r C o m m a n d In p u t C u rr e n t C h ip S ta te (8 ) R ead A r ra y (3 ) S e tu p (4 ,5 ) E ra s e S e tu p ( 4 ,5 ) E nhanced F a c to r y Pgm S e tu p Ready (4 ) (F F H ) (1 0 H /4 0 H ) (2 0 H ) (3 0 H ) R eady P ro g r a m S e tu p E ra s e S e tu p EFP S e tu p L o c k /C R S e tu p OTP P ro g r a m R e a d y (L o c k E r ro r ) B E C o n firm , P /E R e s u m e , ULB C o n firm (9 ) (D 0 H ) P r o g ra m / E ra s e S uspend R ead S ta tu s (B 0 H ) (7 0 H ) R e g is te r Read ID /Q u e ry (6 ) (5 0 H ) (9 0 H , 9 8 H ) R eady R eady S e tu p C le a r S ta tu s R e a d y (L o c k E r ro r ) O TP B usy Busy S e tu p P ro g ra m P r o g ra m B u s y Busy P r o g ra m B u s y P r o g ra m S u s p e n d P gm B usy S e tu p R e a d y ( E rr o r ) E ra s e B u s y Busy S uspend E ra s e S uspend P g m in E ra s e S u s p S e tu p E ra s e B u s y E ra s e B u s y E ra s e S u s p e n d P r o g r a m in E ra s e S u s p e n d B u s y Busy P g m S u s p in E ra s e S u s p P r o g r a m in E ra s e S u s p e n d B u s y S uspend P r o g ra m in E r a s e S u s p e n d B u s y P ro g r a m S u s p e n d in E r a s e S u s p e n d P g m in E r a s e S usp B usy P ro g r a m S u s p e n d in E r a s e S u s p e n d E r a s e S u s p e n d ( L o c k E rr o r) E ra s e S u s p E ra s e S u s p e n d ( L o c k E r r o r) E FP B usy R e a d y ( E rr o r ) L o c k /C R S e tu p in E r a s e Suspend Enhanced F a c to ry P ro g ra m R e a d y ( E rr o r ) E ra s e S u s p E ra s e S u s p e n d S e tu p P ro g ra m B u s y P ro g r a m S u s p e n d E ra s e B u s y E ra s e P r o g r a m in E ra s e S u s p e n d P gm S usp S uspend S e tu p R e a d y ( E rr o r ) (7 ) E FP B usy E FP B usy E F P V e r ify V e rify B u s y (7 ) O u tp u t N e x t S ta te T a b le (1 ) O u t p u t N e x t S t a t e a f te r C o m m a n d In p u t 98 P g m S e tu p , E r a s e S e tu p , O T P S e tu p , P g m in E ra s e S u s p S e tu p , E F P S e tu p , EFP B usy, V e r ify B u s y S ta tu s L o c k /C R S e tu p , L o c k /C R S e tu p in E r a s e S u s p S ta tu s O TP B usy Ready, Pgm B usy, Pgm S uspend, E ra s e B u s y , E ra s e S u s p e n d , P g m In E r a s e S u s p B u s y , P g m S u s p In E ra s e S u s p S ta tu s A r ra y (3 ) S ta tu s O u tp u t d o e s n o t c h a n g e S ta tu s O u tp u t does not change ID /Q u e ry Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) Appendix A Write State Machine States Figure 42. Write State Machine -- Next State Table (Sheet 2 of 2) W r ite S ta t e M a c h in e (W S M ) N e x t S ta t e T a b le C h ip N e x t S t a t e a f t e r C o m m a n d In p u t C u r re n t C h ip S ta te (8 ) Lock, U n lo c k , L o c k -d o w n , C R s e tu p S e tu p (5 ) (5 ) (6 0 H ) (C 0 H ) Ready L o c k /C R S e tu p O TP S e tu p L o c k /C R S e t u p R e a d y (L o c k E rr o r ) OTP LockD ow n B lo c k Lock B lo c k O TP C o n firm (9 ) C o n f irm (9 ) (9 ) C o n firm (0 1 H ) W r it e C R (2 F H ) (0 3 H ) E nhanced Fact P gm E x it ( b lk a d d <> W A0) (X X X X H ) I lle g a l com m ands or E F P d a ta (2 ) (o th e r c o d e s ) R eady R eady R eady S e tu p R eady N /A R e a d y ( L o c k E rr o r) O TP B usy B usy P ro g r a m R eady S e tu p P ro g ra m B u s y N /A B usy P ro g ra m B u s y R eady S uspend P ro g r a m S u s p e n d S e tu p R e a d y (E r ro r ) B usy E ra s e S uspend P ro g r a m in E ra s e S u s p e n d N /A E ra s e B u s y L o c k /C R S e t u p in E ra s e S u s p E ra s e B u s y E ra s e S u s p e n d S e tu p P r o g ra m in E ra s e S u s p e n d B u s y B usy P r o g ra m in E ra s e S u s p e n d B u s y S uspend P r o g r a m S u s p e n d in E ra s e S u s p e n d L o c k /C R S e t u p in E ra s e S uspend E nhanced F a c t o ry P ro g r a m W SM O p e r a t io n C o m p le te s E ra s e S u s p e n d (L o c k E rr o r ) E ra s e S u s p S e tu p E ra s e S u s p E ra s e S u s p R eady N /A E ra s e S uspend E ra s e S u s p e n d ( L o c k E r r o r) N /A R e a d y (E r ro r ) E FP B usy E FP B usy E F P V e r if y (7 ) V e rif y B u s y (7 ) E F P V e r if y E FP B usy (7 ) R eady E F P V e rif y (7 ) R eady O u t p u t N e x t S t a t e T a b le (1) O u t p u t N e x t S t a t e a f t e r C o m m a n d In p u t P g m S e tu p , E ra s e S e tu p , O T P S e tu p , P g m in E ra s e S u s p S e t u p , E F P S e tu p , E FP Busy, V e r if y B u s y S ta tu s L o c k /C R S e t u p , L o c k /C R S e t u p in E ra s e S u s p S ta tu s A rra y S ta tu s O TP B usy Ready, P gm B usy, P gm S uspend, E ra s e B u s y , E ra s e S u s p e n d , P g m In E ra s e S u s p B u s y , P g m S u s p I n E ra s e S u s p S t a tu s O u tp u t d o e s n o t c h a n g e A rr a y O u tp u t d o e s not change O u tp u t d o e s not change Notes: 1. The output state shows the type of data that appears at the outputs if the partition address is the same as the command address. A partition can be placed in Read Array, Read Status or Read ID/CFI, depending on the command issued. Each partition stays in its last output state (Array, ID/CFI or Status) until a new command changes it. The next WSM state does not depend on the partition's output state. For example, if partition #1's output state is Read Array and partition #4's output state is Read Status, every read from partition #4 (without issuing a new command) outputs the Status register. Preliminary Datasheet 99 Intel(R) Wireless Flash Memory (W18) Appendix A Write State Machine States 2. 3. 4. 5. 6. 7. 8. 9. 10. 100 Illegal commands are those not defined in the command set. All partitions default to Read Array mode at power-up. A Read Array command issued to a busy partition results in undermined data when a partition address is read. Both cycles of 2 cycles commands should be issued to the same partition address. If they are issued to different partitions, the second write determines the active partition. Both partitions will output status information when read. If the WSM is active, both cycles of a 2 cycle command are ignored. This differs from previous Intel devices. The Clear Status command clears Status Register error bits except when the WSM is running (Pgm Busy, Erase Busy, Pgm Busy In Erase Suspend, OTP Busy, EFP modes) or suspended (Erase Suspend, Pgm Suspend, Pgm Suspend In Erase Suspend). EFP writes are allowed only when Status Register bit SR.0 = 0. EFP is busy if Block Address = address at EFP Confirm command. Any other commands are treated as data. The "current state" is that of the WSM, not the partition. Confirm commands (Lock Block, Unlock Block, Lock-down Block, Configuration Register) perform the operation and then move to the Ready State. In Erase suspend, the only valid two cycle commands are "Program Word", "Lock/Unlock/Lockdown Block", and "CR Write". Both cycles of other two cycle commands ("OEM CAM program & confirm", "Program OTP & confirm", "EFP Setup & confirm", "Erase setup & confirm") will be ignored. In Program suspend or Program suspend in Erase suspend, both cycles of all two cycle commands will be ignored. Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Appendix B Common Flash Interface (CFI) This appendix defines the data structure or "database" returned by the Common Flash Interface (CFI) Query command. System software should parse this structure to gain critical information such as block size, density, x8/x16, and electrical specifications. Once this information has been obtained, the software will know which command sets to use to enable flash writes, block erases, and otherwise control the flash component. The Query is part of an overall specification for multiple command set and control interface descriptions called Common Flash Interface, or CFI. B.1 Query Structure Output The Query database allows system software to obtain information for controlling the flash device. This section describes the device's CFI-compliant interface that allows access to Query data. Query data are presented on the lowest-order data outputs (DQ0-7) only. The numerical offset value is the address relative to the maximum bus width supported by the device. On this family of devices, the Query table device starting address is a 10h, which is a word address for x16 devices. For a word-wide (x16) device, the first two Query-structure bytes, ASCII "Q" and "R," appear on the low byte at word addresses 10h and 11h. This CFI-compliant device outputs 00h data on upper bytes. The device outputs ASCII "Q" in the low byte (DQ0-7) and 00h in the high byte (DQ8-15). At Query addresses containing two or more bytes of information, the least significant data byte is presented at the lower address, and the most significant data byte is presented at the higher address. In all of the following tables, addresses and data are represented in hexadecimal notation, so the "h" suffix has been dropped. In addition, since the upper byte of word-wide devices is always "00h," the leading "00" has been dropped from the table notation and only the lower byte value is shown. Any x16 device outputs can be assumed to have 00h on the upper byte in this mode. Table 38. Summary of Query Strucutre Output as a Function of Device and Mode Device Device Addresses Preliminary Datasheet Hex Offset Hex Code ASCII Value 00010 51 "Q" 00011 52 "R" 00012 59 "Y" 101 Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Table 39. Example of Query Structure Output of x16 and x8 Devices Word Addressing Offset Hex Code AX - A0 B.2 Byte Addressing Value Offset Hex Code AX - A0 D16 - D0 Value D7 - D0 00010h 0051 "Q" 00010h 51 "Q" 00011h 0052 "R" 00011h 52 "R" 00012h 0059 "Y" 00012h 59 "Y" 00013h P IDLO P rVendor 00013h P IDLO P rVendor 00014h P IDHI ID # 00014h P IDLO ID # 00015h PLO P rVendor 00015h P IDHI ID # 00016h PHI TblAdr 00016h ... ... 00017h A IDLO AltVendor 00017h ... ... 00018h A IDHI ID # 00018h ... ... Query Structure Overview The Query command causes the flash component to display the Common Flash Interface (CFI) Query structure or "database." The structure sub-sections and address locations are summarized below. Table 40. Query Structure Offset 00000h 00001h (2) (BA+2)h 00004-Fh 00010h 0001Bh 00027h (3) P Sub-Section Name (1) Description Manufacturer Code Device Code Block Status register Block-specific information Reserved Reserved for vendor-specific information CFI query identification string Command set ID and vendor data offset System interface information Device timing & voltage information Device geometry definition Flash device layout Vendor-defined additional information specific Primary Intel-specific Extended Query Table to the Primary Vendor Algorithm Notes: 1. Refer to the Query Structure Output section and offset 28h for the detailed definition of offset address as a function of device bus width and mode. 2. BA = Block Address beginning location (i.e., 08000h is block 1's beginning location when the block size is 32K-word). 3. Offset 15 defines "P" which points to the Primary Intel-specific Extended Query Table. B.3 Block Status Register The Block Status Register indicates whether an erase operation completed successfully or whether a given block is locked or can be accessed for flash program/erase operations. 102 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Block Erase Status (BSR.1) allows system software to determine the success of the last block erase operation. BSR.1 can be used just after power-up to verify that the VCC supply was not accidentally removed during an erase operation. Table 41. Block Status Register Offset Length Description (1) (BA+2)h 1 Block Lock Status Register BSR.0 Block lock status 0 = Unlocked 1 = Locked BSR.1 Block lock-down status 0 = Not locked down 1 = Locked down BSR 2-7: Reserved for future use Add. Value BA+2 --00 or --01 BA+2 (bit 0): 0 or 1 BA+2 (bit 1): 0 or 1 BA+2 (bit 2-7): 0 Notes: 1. BA = Block Address beginning location (i.e., 08000h is block 1's beginning location when the block size is 32K-word). B.4 CFI Query Identification String The Identification String provides verification that the component supports the Common Flash Interface specification. It also indicates the specification version and supported vendor-specified command set(s). Preliminary Datasheet 103 Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Table 42. Table 43. 104 CFI Identification Addr. Hex Code Value Query-unique ASCII string "QRY" 10: 11: 12: --51 --52 --59 "Q" "R" "Y" 2 Primary vendor command set and control interface ID code. 16-bit ID code for vendor-specific algorithms. 13: 14: --03 --00 -- 15h 2 Extended Query Table primary algorithm address 15: 16: --39 --00 -- 17h 2 Alternate vendor command set and control interface ID code. 0000h means no second vendor-specified algorithm exists. 17: 18: --00 --00 -- 19h 2 Secondary algorithm Extended Query Table address. 0000h means none exists. 19: 1A: --00 --00 -- Offset Length 10h 3 13h Description System Interface Information Offset Length Description 1Bh 1 1Ch 1 1Dh 1 1Eh 1 1Fh 20h 21h 22h 23h 24h 25h 26h 1 1 1 1 1 1 1 1 VCC logic supply minimum program/erase voltage bits 0-3 BCD 100 mV bits 4-7 BCD volts VCC logic supply maximum program/erase voltage bits 0-3 BCD 100 mV bits 4-7 BCD volts VPP [programming] supply minimum program/erase voltage bits 0-3 BCD 100 mV bits 4-7 HEX volts VPP [programming] supply maximum program/erase voltage bits 0-3 BCD 100 mV bits 4-7 HEX volts n "n" such that typical single word program time-out = 2 -sec n "n" such that typical max. buffer write time-out = 2 -sec "n" such that typical block erase time-out = 2n m-sec "n" such that typical full chip erase time-out = 2n m-sec n "n" such that maximum word program time-out = 2 times typical n "n" such that maximum buffer write time-out = 2 times typical "n" such that maximum block erase time-out = 2n times typical "n" such that maximum chip erase time-out = 2n times typical Hex Add. Code Value 1B: --17 1.7V 1C: --19 1.9V 1D: --B4 11.4V 1E: --C6 12.6V 1F: 20: 21: 22: 23: 24: 25: 26: --04 16s --00 NA --0A 1s --00 NA --04 256s --00 NA --03 8s --00 NA Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) B.5 Device Geometry Definition Table 44. Device Geometry Definition Offset 27h 28h Length Description n "n" such that device size = 2 in number of bytes 1 Flash device interface code assignment: "n" such that n+1 specifies the bit field that represents the flash device width capabilities as described in the table: 2 2Ah 2 2Ch 1 2Dh 31h 35h 6 5 4 3 2 1 0 -- -- -- x64 x32 x16 x8 15 14 13 12 11 10 9 8 -- -- -- -- -- -- -- -- n "n" such that maximum number of bytes in write buffer = 2 Number of erase block regions (x) within device: 1. x = 0 means no erase blocking; the device erases in bulk 2. x specifies the number of device regions with one or more contiguous same-size erase blocks. 3. Symmetrically blocked partitions have one blocking region Erase Block Region 1 Information bits 0-15 = y, y+1 = number of identical-size erase blocks bits 16-31 = z, region erase block(s) size are z x 256 bytes 4 4 Erase Block Region 2 Information bits 0-15 = y, y+1 = number of identical-size erase blocks bits 16-31 = z, region erase block(s) size are z x 256 bytes 4 Reserved for future erase block region information Address 27: 28: 29: 2A: 2B: 2C: 2D: 2E: 2F: 30: 31: 32: 33: 34: 35: 36: 37: 38: Preliminary Datasheet 7 -- 32 Mbit -B -T --16 --16 --01 --01 --00 --00 --00 --00 --00 --00 --02 --02 --07 --3E --00 --00 --20 --00 --00 --01 --07 --3E --00 --00 --20 --00 --00 --01 --00 --00 --00 --00 --00 --00 --00 --00 64 Mbit -B -T --17 --17 --01 --01 --00 --00 --00 --00 --00 --00 --02 --02 --07 --7E --00 --00 --20 --00 --00 --01 --07 --7E --00 --00 --20 --00 --00 --01 --00 --00 --00 --00 --00 --00 --00 --00 Code 27: See table below 28: --01 x16 29: 2A: 2B: 2C: --00 --00 --00 0 See table below 2D: 2E: 2F: 30: 31: 32: 33: 34: 35: 36: 37: 38: See table below See table below See table below 128 Mbit -B -T --18 --18 --01 --01 --00 --00 --00 --00 --00 --00 --02 --02 --07 --FE --00 --00 --20 --00 --00 --01 --07 --FE --00 --00 --20 --00 --00 --01 --00 --00 --00 --00 --00 --00 --00 --00 105 Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) B.6 Intel-Specific Extended Query Table Table 45. Primary Vendor-Specific Extended Query 106 Offset(1) P = 39h (P+0)h (P+1)h (P+2)h (P+3)h (P+4)h (P+5)h (P+6)h (P+7)h (P+8)h Length (P+9)h 1 (P+A)h (P+B)h 2 3 1 1 4 (P+C)h 1 (P+D)h 1 Description (Optional flash features and commands) Primary extended query table Unique ASCII string "PRI" Major version number, ASCII Minor version number, ASCII Optional feature and command support (1=yes, 0=no) bits 10-31 are reserved; undefined bits are "0." If bit 31 is "1" then another 31 bit field of Optional features follows at the end of the bit-30 field. bit 0 Chip erase supported bit 1 Suspend erase supported bit 2 Suspend program supported bit 3 Legacy lock/unlock supported bit 4 Queued erase supported bit 5 Instant individual block locking supported bit 6 Protection bits supported bit 7 Pagemode read supported bit 8 Synchronous read supported bit 9 Simultaneous operations supported Supported functions after suspend: read Array, Status, Query Other supported operations are: bits 1-7 reserved; undefined bits are "0" bit 0 Program supported after erase suspend Block status register mask bits 2-15 are Reserved; undefined bits are "0" bit 0 Block Lock-Bit Status register active bit 1 Block Lock-Down Bit Status active VCC logic supply highest performance program/erase voltage bits 0-3 BCD value in 100 mV bits 4-7 BCD value in volts VPP optimum program/erase supply voltage bits 0-3 BCD value in 100 mV bits 4-7 HEX value in volts Add. 39: 3A: 3B: 3C: 3D: 3E: 3F: 40: 41: bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 8 bit 9 42: Hex Code Value --50 "P" --52 "R" --49 "I" --31 "1" --33 "3" --E6 --03 --00 --00 =0 No =1 Yes =1 Yes =0 No =0 No =1 Yes =1 Yes =1 Yes =1 Yes =1 Yes --01 bit 0 43: 44: bit 0 bit 1 45: =1 --03 --00 =1 =1 --18 Yes 46: --C0 12.0V Yes Yes 1.8V Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Table 46. Protection Register Information Offset P = 39h (P + E)h Lengt h Number of Protectuib Register fields in JEDEC ID space. "00h" indicates that 256 protection fields are available. 1 Protection Field 1: Protection Description This field describes user-available One Time Programmable (OTP) Protection Register bytes, Some are pre-programmed with device-unique serial numbers. Others are user-programmable. Bits are 0-15 point to the Protection Register lock byte, the section's first byte. The following bytes are factory pre-programmed and userprogrammable: (P + E)h (P + 10)h (P + 11)h (P + 12)h Table 47. 4 * * * * bits 0-7 = Lock/bytes JEDEC-plane physical low address Add. Hex Code Value 47: --01 1 48: --80 80h 49: 4A: 4B: --00 --03 --03 00h 8 byte 8 byte bites 8-15 = Lock/bytes JEDEC-plane physical high address bits 16-23 = "n" such that 2n = factory pre-programmed bytes bits 24-31 = "n" such that 2n = user-programmable bytes Burst Read Information for Non-muxed Device (1) Table 48. Description (Optional Flash Features and Commands) Offset P = 39h (P+13)h Length (P+14)h 1 (P+15)h 1 (P+16)h (P+17)h (P+18)h 1 1 1 1 Description (Optional flash features and commands) Page Mode Read capability n bits 0-7 = "n" such that 2 HEX value represents the number of read-page bytes. See offset 28h for device word width to determine page-mode data output width. 00h indicates no read page buffer. Number of synchronous mode read configuration fields that follow. 00h indicates no burst capability. Synchronous mode read capability configuration 1 Bits 3-7 = Reserved n+1 bits 0-2 "n" such that 2 HEX value represents the maximum number of continuous synchronous reads when the device is configured for its maximum word width. A value of 07h indicates that the device is capable of continuous linear bursts that will output data until the internal burst counter reaches the end of the device's burstable address space. This field's 3-bit value can be written directly to the Read Configuration Register bits 0-2 if the device is configured for its maximum word width. See offset 28h for word width to determine the burst data output width. Synchronous mode read capability configuration 2 Synchronous mode read capability configuration 3 Synchronous mode read capability configuration 4 Hex Add. Code Value 4C: --03 8 byte 4D: --04 4 4E: --01 4 4F: 50: 51: --02 --03 --07 8 16 Cont Partition and Erase-block Region Information (1) Offset P = 39h Description Bottom (Optional flash features and commands) Top (P+19)h (P+19)h Number of device hardware-partition regions within the device. x = 0: a single hardware partition device (no fields follow). x specifies the number of device partition regions containing one or more contiguous erase block regions. Preliminary Datasheet See table below Address Bot Top Len 1 52: 52: 107 Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Table 49. Partition Region 1 Information (1) Offset P = 39h Description Bottom Top (Optional flash features and commands) (P+1A)h (P+1A)h Number of identical partitions within the partition region (P+1B)h (P+1B)h (P+1C)h (P+1C)h Number of program or erase operations allowed in a partition bits 0-3 = number of simultaneous Program operations bits 4-7 = number of simultaneous Erase operations (P+1D)h (P+1D)h Simultaneous program or erase operations allowed in other partitions while a partition in this region is in Program mode bits 0-3 = number of simultaneous Program operations bits 4-7 = number of simultaneous Erase operations (P+1E)h (P+1E)h Simultaneous program or erase operations allowed in other partitions while a partition in this region is in Erase mode bits 0-3 = number of simultaneous Program operations bits 4-7 = number of simultaneous Erase operations (P+1F)h (P+1F)h Types of erase block regions in this Partition Region. x = 0 = no erase blocking; the Partition Region erases in bulk x = number of erase block regions w/ contiguous same-size erase blocks. Symmetrically blocked partitions have one blocking region. Partition size = (Type 1 blocks)x(Type 1 block sizes) + (Type 2 blocks)x(Type 2 block sizes) +...+ (Type n blocks)x(Type n block sizes) (P+20)h (P+20)h Partition Region 1 Erase Block Type 1 Information (P+21)h (P+21)h bits 0-15 = y, y+1 = number of identical-size erase blocks (P+22)h (P+22)h bits 16-31 = z, region erase block(s) size are z x 256 bytes (P+23)h (P+23)h (P+24)h (P+24)h Partition 1 (Erase Block Type 1) Minimum block erase cycles x 1000 (P+25)h (P+25)h (P+26)h (P+26)h Partition 1 (erase block Type 1) bits per cell; internal ECC bits 0-3 = bits per cell in erase region bit 4 = reserved for "internal ECC used" (1=yes, 0=no) bits 5-7 = reserve for future use (P+27)h (P+27)h Partition 1 (erase block Type 1) page mode and synchronous mode capabilities defined in Table 10. bit 0 = page-mode host reads permitted (1=yes, 0=no) bit 1 = synchronous host reads permitted (1=yes, 0=no) bit 2 = synchronous host writes permitted (1=yes, 0=no) bits 3-7 = reserved for future use (P+28)h Partition Region 1 Erase Block Type 2 Information (P+29)h bits 0-15 = y, y+1 = number of identical-size erase blocks (P+2A)h bits 16-31 = z, region erase block(s) size are z x 256 bytes (P+2B)h (bottom parameter device only) (P+2C)h Partition 1 (Erase block Type 2) (P+2D)h Minimum block erase cycles x 1000 (P+2E)h Partition 1 (Erase block Type 2) bits per cell bits 0-3 = bits per cell in erase region bit 4 = reserved for "internal ECC used" (1=yes, 0=no) bits 5-7 = reserve for future use (P+2F)h Partition 1 (Erase block Type 2) pagemode and synchronous mode capabilities defined in Table 10 bit 0 = page-mode host reads permitted (1=yes, 0=no) bit 1 = synchronous host reads permitted (1=yes, 0=no) bit 2 = synchronous host writes permitted (1=yes, 0=no) bits 3-7 = reserved for future use 108 See table below Address Bot Top Len 2 53: 53: 54: 54: 1 55: 55: 1 56: 56: 1 57: 57: 1 58: 58: 4 1 59: 5A: 5B: 5C: 5D: 5E: 5F: 59: 5A: 5B: 5C: 5D: 5E: 5F: 1 60: 60: 4 1 61: 62: 63: 64: 65: 66: 67: 1 68: 2 2 Preliminary Datasheet Intel(R) Wireless Flash Memory (W18) Appendix B Common Flash Interface (CFI) Table 50. Partition and Erase Block Region Information Address 52: 53: 54: 55: 56: 57: 58: 59: 5A: 5B: 5C: 5D: 5E: 5F: 60: 61: 62: 63: 64: 65: 66: 67: 68: 69: 6A: 6B: 6C: 6D: 6E: 6F: 70: 71: 72: 73: 74: 75: 76: 32 Mbit -B --02 --01 --00 --11 --00 --00 --02 --07 --00 --20 --00 --64 --00 --01 --03 --06 --00 --00 --01 --64 --00 --01 --03 --07 --00 --11 --00 --00 --01 --07 --00 --00 --01 --64 --00 --01 --03 -T --02 --07 --00 --11 --00 --00 --01 --07 --00 --00 --01 --64 --00 --01 --03 --01 --00 --11 --00 --00 --02 --06 --00 --00 --01 --64 --00 --01 --03 --07 --00 --20 --00 --64 --00 --01 --03 64Mbit -B --02 --01 --00 --11 --00 --00 --02 --07 --00 --20 --00 --64 --00 --01 --03 --06 --00 --00 --01 --64 --00 --01 --03 --0F --00 --11 --00 --00 --01 --07 --00 --00 --01 --64 --00 --01 --03 -T --02 --0F --00 --11 --00 --00 --01 --07 --00 --00 --01 --64 --00 --01 --03 --01 --00 --11 --00 --00 --02 --06 --00 --00 --01 --64 --00 --01 --03 --07 --00 --20 --00 --64 --00 --01 --03 128Mbit -B -T --02 --02 --01 --1F --00 --00 --11 --11 --00 --00 --00 --00 --02 --01 --07 --07 --00 --00 --20 --00 --00 --01 --64 --64 --00 --00 --01 --01 --03 --03 --06 --01 --00 --00 --00 --11 --01 --00 --64 --00 --00 --02 --01 --06 --03 --00 --1F --00 --00 --01 --11 --64 --00 --00 --00 --01 --01 --03 --07 --07 --00 --00 --00 --20 --01 --00 --64 --64 --00 --00 --01 --01 --03 --03 Notes: 1. The variable P is a pointer which is defined at CFI offset 15h. 2. TPD - Top parameter device; BPD - Bottom parameter device. 3. Partition: Each partition is 4-Mbit in size. It can contain main blocks OR a combination of both main and parameter blocks. 4. Partition Region: Symmetrical partitions form a partition region. There are two partition regions: A contains all the partitions that are made up of main blocks only; B contains the partition made up of the parameter and the main blocks. Preliminary Datasheet 109 Intel(R) Wireless Flash Memory (W18) Appendix C Ordering Information Appendix C Ordering Information Figure 43. VF BGA Ordering Information G E 2 8 F 6 4 0 W 1 8 T E 6 0 Access Speed (ns) (60,80) Package: GE = VF BGA, Leaded PH = VF BGA, Pb-free Process Identifier: C = 180 nm D = 130 nm E = 90 nm Product Line Designator: for all Intel Flash Products Parameter Location: Device Density: T = Top Parameter B = Bottom Parameter 320 = 32Mbit 640 = 64Mbit 128 = 128Mbit Product Family: W18 = Intel (R) Wireless Flash Memory Flash 3 & 4 Flash 1 & 2 Flash 4 Flash 3 Flash 2 SCSP Ordering Information Flash 1 Figure 44. R D 4 8 F 3 0 0 0 W 0 Y B Q 0 Package: Device Details: RD = SCSP, Leaded PF = SCSP, Pb-Free 0 = Initial Version Ballout Indicator: Product Line: Q= QUAD+ 48F = Flash Only Parameter Location: Flash Density: 0 = No die 3 = 128 Mbit Product Family Designator: T = Top Parameter B = Bottom Parameter Voltage: Y = 1.8 Volt I/O W = Intel(R) Wireless Flash Memory 110 Preliminary Datasheet