1
3
Notice for TAIYO YUDEN products　
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2012. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called TAIYO YUDENs official sales channel).
It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and For-
eign Trade Control Law of Japan, U.S. Export Administration Regulations, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
HIGH FREQUENCY PRODUCTS
■ ORDERING CODE
■ EXTERNAL DIMENSIONS/STANDARD QUANTITY
Unit : mm Unit : mm
Unit : mm
Unit : mmUnit : mm
Unit : mm
Unit : mm Unit : mm
Unit : mm
Unit : mm
Unit : mm
Unit : mm
FI 212B Type
FI 212C245033/FI 212C245034
FI 212P Type
FI 212L Type
FI 212C Type FI 212C249566/FI 212C355068
FI 168D Type
FI 325P Type
FI 105B/L Type
FI 212B190223
FI 168B/L Type
FI 168P Type
FI 168T Type
2.00±0.15
0.3±0.10
0.65Max
1.6±0.10
0.50±0.15
0.2±0.15
0.5max.
0.80±0.10
1.6±0.10
0.50±0.15
0.2±0.15
0.45max.
0.80±0.10
1.6±0.10
0.50±0.15
0.2±0.15
0.45max.
0.80±0.10
3.2±0.20
1.0±0.10
0.55±0.20
2.5±0.20
1.0max
1.00±0.05
0.30±0.10
0.4 Max.
0.30±0.10
0.50±0.05
0.10±0.05
0.10±0.05
FI 212C245075
120
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
MULTILAYER CERAMIC DEVICES (FILTERS / DIPLEXERS / BALUNS)
❷Electrode code
△With Plating
△＝Blank space
❸Dimensions code
［mm］
325 3.2×2.5
212 2.0×1.25
168 1.6×0.8
105 1.0×0.5
❶Device code
FI Filters for
High Frequency
❻Spec Code
01〜Individual Spec
❼Packaging
ーT Tape & Reel
❹Special Code
B Band Pass Filter
L Low Pass Filter
C Balance Filter
P Diplexer
T Balun
D Dual Filter
❺Frequency 〔MHz〕
example
2450 2400〜2500
0620 470〜770
F I △2 1 2 B 2 4 5 0 2 6 ーT
❶ ❷ ❸ ❹ ❺ ❻ ❼
REFLOW
Unit : mm Unit : mm
FI 325P Type FI 212C2450XX FI 212C245051 FI 212C249566
FI 212C355068
FI 212P245003/
FI212P089208/
FI212P085912
FI 212P089213/
FI 212P085909 FI 168T Type FI 168P245010/
FI 168P245023 FI 168D087018 FI 168P 157519
（1）
GND Balanced Balanced Balanced GND GND Unbalance GND High Band IN GND
（2）
Common GND GND GND Common Port Common Port GND Low Band GND High Band
（3）
GND Balanced Balanced Balanced GND GND Balanced Common Low Band IN Common
（4）
High Band GND GND GND High Band Low Band Balanced High Band Low Band OUT Low Band
（5）
GND Unbalance Unbalance Unbalance GND GND GND ーGND ー
（6）
Low Band DC NC NC or DC Low Band High Band NC ーHigh Band
OUT ー
（7）
ーNC NC NC ーーーーーー
（8）
ーGND GND GND ーーーーーー
Type
Standard Quantity ［pcs］
325P 2000
212B
3000〜
6000
212L
212C
212P
168B
4000〜
8000
168L
168T
168D
168P
105B 10000
105L
HIGH FREQUENCY PRODUCTS
FI 168B245001
Pass band frequency
2400 – 2500MHz
Insertion loss at
pass band
2.2 dB （25deg-C）
2.5 dB （−30〜＋85deg-C）
Ripple at pass band
1.0 dB max.
V.S.W.R. at pass band
2.1 max.
Attenuation
25 dB min. （880 – 960MHz）
25 dB min. （1710 – 1910MHz）
20 dB min. （4800 – 5000MHz）
20 dB min. （7200 – 7500MHz）
Impedance 50 ohm
FI 105B245024
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
3.0 dB max.（25 deg-C）
3.3 dB max.（−40〜＋85 deg-C）
Ripple at pass band
1.0 dB max.
V.S.W.R. at pass band
2.2 max.
Attenuation
25 dB min.（880 - 960 MHz）
22 dB min.（1710 - 1910 MHz）
20 dB min.（4800 - 5000 MHz）
20 dB min.（7200 - 7500 MHz）
FI 168B250065
FI 168B24956D
Pass band frequency
2300 - 2700 MHz
Insertion loss at
2300 - 2500 MHz
2.4 dB max.（25 deg-C）
2.6 dB max.（−30〜＋85 deg-C）
Insertion loss at
2500 - 2700 MHz
2.3 dB max. （25 deg-C）
2.5 dB max. （−30〜＋85 deg-C）
Ripple at
2300 - 2500 MHz 1.4 dB max.
Ripple at
2500 - 2700 MHz 1.3 dB max.
V.S.W.R. at
2300 - 2500 MHz 2.4 max.
V.S.W.R. at
2500 - 2700 MHz 1.3 max.
Attenuation 15 dB min.（1500 - 2000 MHz）
10 dB min.（4600 - 8000 MHz）
Impedance 50 ohm
Pass band frequency
2300 - 2690MHz
Insertion loss at
pass band
2.3 dB （25deg-C）
2.6 dB （
−
30〜+85deg-C）
Ripple at pass
band 0.8 dB max.
V.S.W.R. at pass
band 2.1 max.
Attenuation
15 dB min. (DC-1620MHz)
23 dB min. (3490-4000MHz)
25 dB min. (4490-8000MHz)
Impedance 50 ohm
■ PART NUMBERS
■ ELECTRICAL CHARACTERISTICS・TYPICAL CHARACTERISTICS
FI 212B245026
Pass band frequency
2400 - 2500 MHz
Insertion loss at
pass band
2.6 dB max.（25 deg-C）
2.9 dB max.（−40〜＋85 deg-C）
Ripple at
pass band 1.0 dB max.
V.S.W.R. at
pass band 2.0 max.
Attenuation
40 dB min.（800 - 960 MHz）
30 dB min.（1710 - 1990 MHz）
25 dB min.（2110 - 2170 MHz）
30 dB min.（4800 - 5000 MHz）
30 dB min.（7200 - 7500 MHz）
Impedance 50 ohm
FI 212B245027
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
1.4 dB max.（25 deg-C）
1.7 dB max.（−40〜＋85 deg-C）
Ripple at pass band
1.0 dB max.
V.S.W.R. at pass band
2.0 max.
Attenuation
30 dB min.（800 - 915 MHz）
30 dB min.（1710 - 1910 MHz）
6 dB min.（2110 - 2170 MHz）
20 dB min.（4800 - 5000 MHz）
121
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
㻘㻓㻓 㻔㻘㻓㻓 㻕㻘㻓㻓 㻖㻘㻓㻓 㻗㻘㻓㻓 㻘㻘㻓㻓 㻙㻘㻓㻓 㻚㻘㻓㻓 㻛㻘㻓㻓
㻓㻑㻓㻕㻑㻓 㻗㻑㻓㻙㻑㻓 㻛㻑㻓
㻔㻑㻓㻕㻑㻓 㻖㻑㻓㻗㻑㻓 㻘㻑㻓㻙㻑㻓 㻚㻑㻓㻛㻑㻓
●Multi-layer balance filters
●Multi-layer diplexer
●Multi-layer band pass filters
●Multi-layer low pass filters
●Multi-layer Balun
Applications External dimensions Ordering code Notes
2.4GHz W-LAN
Bluetooth
2.0×1.25×1.0 max. FI 212B245026/FI 212B245027
1.6×0.8×0.5 max. FI 168B245001
1.0×0.5×0.4 max. FI 105B245024
WiMAX 1.6×0.8×0.5 max. FI 168B250065/FI168B24956D
PHS 2.0×1.25×1.0 max. FI 212B190223
Applications
External dimensions Ordering code Notes
Digital TV 1.6×0.8×0.45 max. FI 168L062005 Thickness 0.45 mm max.
WiMAX 1.6×0.8×0.45 max. FI 168L259764 Thickness 0.45 mm max.
2.4GHz W-LAN
Bluetooth
1.0×0.5×0.4 max. FI 105L250014 Thickness 0.4 mm max.
Other 1.6×0.8×0.45 max. FI 168D087018 Dual band LPF
Applications
External dimensions Ordering code Notes
Bluetooth
2.0×1.25×1.0 max. FI 212C245032 Conjugated match to CSR BC4
2.0×1.25×1.0 max. FI 212C245033 Conjugated match to CSR BC3
2.0×1.25×1.0 max. FI 212C245034
Conjugated match to CSR BC4-BGA
2.0×1.25×1.0 max. FI 212C245036 Conjugated match to CSR BC5
2.0×1.25×1.0 max. FI 212C245051
Conjugated match to STLC2500C-D
2.0×1.25×0.7 max. FI 212C245075
Conjugated match to CSR BC5FM, BC6ROM
WiMAX 2.0×1.25×0.5 max. FI 212C249566 Thickness 0.5 mm max.
2.0×1.25×0.5 max. FI 212C355068 Thickness 0.5 mm max.
Applications
External dimensions Ordering code Notes
BS 1.6×0.8×0.5 max. FI 168T155021 Thickness 0.5 mm max.
Applications
External dimensions Ordering code Notes
W-LAN
2.0×1.25×1.0 max. FI 212P245003
1.6×0.8×0.65 max. FI 168P245010
FI 168P245023
Cellular 2.0×1.25×1.0 max.
FI 212P089208
FI 212P089213
FI 212P085909
FI 212P085912
GPS/
2.4GHz W-LAN
1.6×0.8×0.65 max. FI 168P157519
BS 3.2×2.5×1.0 max. FI325P120057
㻓㻑㻓
㻓
㻐㻔㻓
㻐㻕㻓
㻐㻖㻓
㻐㻗㻓
㻐㻘㻓
㻐㻙㻓
㻐㻚㻓
㻕㻑㻓㻗㻑㻓 㻙㻑㻓㻛㻑㻓
㻘㻓㻓 㻔㻘㻓㻓 㻕㻘㻓㻓 㻖㻘㻓㻓 㻗㻘㻓㻓 㻘㻘㻓㻓
HIGH FREQUENCY PRODUCTS
■ ELECTRICAL CHARACTERISTICS・TYPICAL CHARACTERISTICS
Pass band frequency
1884-1930MHz
Insertion Loss at
1884-1920MHz
1.7 dB max. （25deg-C）
2.0 dB max. （−30-＋85deg-C）
Insertion Loss at
1920-1930MHz
1.7 dB max. （25deg-C）
2.0 dB max. （−30-＋85deg-C）
Ripple at Pass band
1.0 dB max.
V.S.W.R. at Pass band
2.0 max.
Attenuation 30 dB min. （1420MHz）
18 dB min. （3768-3860MHz）
Impedance 50 ohm
FI 105L250014
Pass band frequency
2400-2500MHz
Insertion loss at
2400 - 2500 MHz
0.45 dB max.（25 deg-C）
0.55 dB max.（−40〜＋85 deg-C）
V.S.W.R. at
2400 - 2500 MHz
1.7 max.
Attenuation 21 dB min.（4800 - 5000 MHz）
21 dB min.（7200 - 7500 MHz）
Impedance 50 ohm
122
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
FI 168L259764
Pass band frequency
470 – 770 MHz
2300 – 2700 MHz
Insertion loss at
470-770MHz
0.5 dB max. （25 deg-C）
0.6 dB max. （−30〜＋85 deg-C）
Insertion loss at
2300-2700MHz
0.5 dB max. （25 deg-C）
0.6 dB max. （−30〜＋85 deg-C）
Ripple at 470 – 770 MHz
0.3 dB max.
Ripple at 2300 – 2700 MHz
0.3 dB max.
V.S.W.R.at 470 – 770MHz
2.0 max.
V.S.W.R.at 2300 – 2700MHz
2.0 max.
Attenuation 20 dB min. （4600 – 5400 MHz）
20 dB min. （6900 – 8100 MHz）
Impedance 50 ohm
FI 168L062005
Pass band frequency
470 – 770 MHz
Insertion loss at
470-600MHz
1.2 dB max. （25 deg-C）
1.3 dB max. （−30〜＋85 deg-C）
Insertion loss at
600-710MHz
2.2 dB max. （25 deg-C）
2.4 dB max. （−30〜＋85 deg-C）
Insertion loss at
710-770MHz
4.0 dB max. （25 deg-C）
4.4 dB max. （−30〜＋85 deg-C）
Ripple at 470 – 710 MHz
1.4 dB max.
V.S.W.R. 2.0 max. （470 – 710 MHz）
2.5 max. （710 – 770 MHz）
Attenuation
25 dB min. （888 – 925 MHz）
（25 deg-C）
21 dB min. （888 – 925 MHz）
（−30〜＋85 deg-C）
25 dB min. （940 – 960 MHz）
27 dB min. （1429 – 1453 MHz）
26 dB min. （1920 – 1980 MHz）
26 dB min. （2400 – 2500 MHz）
Impedance 50 ohm
FI 212B190223
㻓㻑㻓㻕㻑㻓 㻗㻑㻓㻙㻑㻓 㻛㻑㻓
FI 168D087018
Low band
Pass band frequency
824 – 915 MHz
Insertion loss at
824 – 915 MHz
0.6 dB max.（−30 to +85 Deg.C）
V.S.W.R.
at 824 – 915 MHz
1.5 max.
Attenuation 25 dB min. （1648-1830MHz）
25 dB min. （2472-2745MHz）
Impedance 50 ohm
High band
Pass band frequency
1710 – 1910 MHz
Insertion loss at
1710 – 1910 MHz
0.6 dB max.（−30 to +85 Deg.C）
V.S.W.R.
at 824 – 915 MHz
1.5 max.
Attenuation 25 dB min. （3420-3820MHz）
25 dB min. （5130-5730MHz）
Impedance 50 ohm
Isolation
In to In/Out to Out 27 dB min. （824-915MHz）
30 dB min. （1710-1910MHz）
In to Out 30 dB min. （824-915MHz）
30 dB min. （1710-1910MHz）
0
-10
-20
-30
-40
-50
0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
S11
S21
0
-10
-20
-30
-40
-50
0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
S11
S21
FI 212C245032
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
3.7 dB （25deg-C）
4.0 dB （−30〜＋85deg-C）
Ripple at pass band
1.0 dB max.
Unbalanced port
V.S.W.R. at pass band
2.0 max.
Balanced port V.S.W.R.
at pass band
2.0 max.
Amplitude Imbalance
at pass band
2.0 dB max.
Phase Imbalance
at pass band 180 ＋/− 10 deg
Attenuation
35 dB min. （880-960MHz）
20 dB min. （1710-1990MHz）
20 dB min. （1990-2170MHz）
20 dB min. （4800-5000MHz）
Unbalanced Port
Impedance 50 ohm
Balanced Port
Impedance Conjugated match to CSR BC4
FI 212C245033
Pass band frequency
2400-2500MHz
Insertion loss at pass
band
2.7 dB （25deg-C）
3.0 dB （−30〜＋85deg-C）
Ripple at pass band
1.0 dB max.
Unbalanced port
V.S.W.R. at pass band
2.0 max.
Balanced port V.S.W.R.
at pass band
2.0 max.
Amplitude Imbalance
at pass band
2.0 dB max.
Phase Imbalance
at pass band 180 ＋/− 10 deg
Attenuation
25 dB min. （880-960MHz）
15 dB min. （1710-1990MHz）
15 dB min. （1990-2170MHz）
15 dB min. （4800-5000MHz）
Unbalanced Port Impedance
50 ohm
Balanced Port
Impedance Conjugated match to CSR BC3
HIGH FREQUENCY PRODUCTS
■ ELECTRICAL CHARACTERISTICS・TYPICAL CHARACTERISTICS
FI 212C245034
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
2.7 dB max.（25 deg-C）
3.0 dB max.（−30〜＋85 deg-C）
Ripple at pass band
1.0 dB max.
Amp. balance at
Passband
2.0 dB Max.
Phase Balance at
Passband
180 ＋/− 10 deg
Unbalanced Port
V.S.W.R at Passband
2.0 max.
Balanced Port
V.S.W.R at Passband
2.0 max.
Attenuation
25 dB min.（880 - 960 MHz）
15 dB min.（1710 - 1990 MHz）
12 dB min.（1990 - 2170 MHz）
15 dB min.（4800 - 5000 MHz）
Unbalanced Port
Impedance 50 ohm
Balanced Port
Impedance
Conjugated to CSR BC4-BGA,
BC5-BGA
123
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
FI 212C355068
2.0 3.0 4.0
Pass band frequency
3300-3800MHz
Insertion loss at
pass band
2.5 dB （25 deg-C）
2.8 dB （-30〜+85 deg-C）
Ripple at pass
band 1.0 dB max.
Unbalanced port
V.S.W.R. at pass band
2.3 max.
Balanced port
V.S.W.R. at pass band
2.3 max.
Amplitude
imbalance at pass
band
2.0 dB max.
Phase imbalance
at pass band 180 ＋/− 12 deg
Attenuation
40 dB min. （1710-1990MHz）
40 dB min. （2110-2170MHz）
35 dB min. （2400-2500MHz）
15 dB min. （4900-5850MHz）
Impedance 50:100
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
3.7 dB （25deg-C）
4.0 dB （−30〜＋85deg-C）
Ripple at pass band
1.0 dB max.
Unbalanced port
V.S.W.R. at pass band
2.0 max.
Balanced port V.S.W.R.
at pass band
2.0 max.
Amplitude Imbalance
at pass band
2.0 dB max.
Phase Imbalance
at pass band 180 ＋/− 10 deg
Attenuation
35 dB min. （880-960MHz）
20 dB min. （1710-1990MHz）
15 dB min. （1990-2170MHz）
20 dB min. （4800-5000MHz）
Unbalanced Port Impedance
50 ohm
Balanced Port
Impedance Conjugated match to CSR BC5
FI 212C245036
㻔㻑㻓
㻓
㻐㻕㻓
㻐㻗㻓
㻐㻙㻓
㻐㻛㻓
㻐㻔㻓㻓
㻤㼗㼗㼈㼑㼘㼄㼗㼌㼒㼑䠭㼇㻥䠯
㻕㻑㻓㻖㻑㻓
㻓㻑㻓
㻓
㻐㻕㻓
㻐㻗㻓
㻐㻙㻓
㻐㻛㻓
㻐㻔㻓㻓
㻤㼗㼗㼈㼑㼘㼄㼗㼌㼒㼑䠭㼇㻥䠯
㻕㻑㻓㻗㻑㻓 㻙㻑㻓
㻶㼇㼖㻔㻔
㻶㼇㼇㻕㻕
㻶㼇㼖㻕㻔
FI 212C245051
FI 212C245075
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
3.7 dB （25deg-C）
4.0 dB （−30〜＋85deg-C）
Ripple at pass band
1.0 dB max.
Unbalanced port
V.S.W.R. at pass band
2.0 max.
Balanced port V.S.W.R.
at pass band
2.0 max.
Amplitude Imbalance
at pass band
2.0 dB max.
Phase Imbalance
at pass band 180 ＋/− 10 deg
Attenuation
40 dB min. （824 – 960MHz）
12 dB min. （1570-1580MHz）
27 dB min. （1710-1785MHz）
25 dB min. （1805-1880MHz）
23 dB min. （1880-1910MHz）
20 dB min. （4800-5000MHz）
Unbalanced Port
Impedance 50 ohm
Balanced Port
Impedance
Conjugated match to
STLC2500C-D
Pass band frequency
2400-2500MHz
Insertion loss at
pass band
3.7 dB （25deg-C）
4.0 dB （−30〜＋85deg-C）
Ripple at pass band
1.0 dB max.
Unbalanced port
V.S.W.R. at pass band
2.2 max.
Balanced port V.S.W.R.
at pass band
2.2 max.
Amplitude Imbalance
at pass band
2.0 dB max.
Phase Imbalance
at pass band 180 ＋/− 10 deg
Attenuation
40 dB min. （880-960MHz）
18 dB min. （1710-1990MHz）
12 dB min. （1990-2170MHz）
30 dB min. （4800-5000MHz）
Unbalanced Port
Impedance 50 ohm
Balanced Port
Impedance
Conjugated match to CSR
BC5FM.BC6ROM
㻓㻑㻛㻔㻑㻕 㻔㻑㻙㻕㻑㻓 㻕㻑㻗㻕㻑㻛
㻓
㻐㻔㻓
㻓
㻐㻔㻓
㻐㻕㻓
㻐㻖㻓
㻐㻗㻓
㻐㻘㻓
㻐㻙㻓
㻐㻚㻓
㻐㻛㻓
㻐㻜㻓
㻐㻔㻓㻓
㻐㻕㻓
㻐㻖㻓
㻐㻗㻓
㻐㻘㻓
㻐㻙㻓
㻐㻚㻓
㻓㻑㻘㻔㻑㻘 㻕㻑㻘㻖㻑㻘 㻗㻑㻘㻘㻑㻘
FI 212C249566
Pass band frequency
2300-2690MHz
Insertion loss
at 2300-2495MHz
2.9 dB max. （25 deg-C）
3.2 dB max. （−30〜＋85 deg-C）
Ripple at 2300-2495MHz
1.2 dB max.
Unbalanced port V.S.W.R.
at 2300-2495MHz
2.3 max.
Balanced port V.S.W.R.
at 2300-2495MHz
2.3 max.
Amplitude Imbalance
at 2300-2495MHz
2.0 dB max.
Phase Imbalance
at 2300-2495MHz 180 ＋/− 12 deg
Insertion loss
at 2495-2690MHz
2.3 dB max. （25 deg-C）
2.6 dB max. （−30〜＋85 deg-C）
Ripple at 2495-2690MHz
1.0 dB max.
Unbalanced port V.S.W.R.
at 2495-2690MHz
2.3 max.
Balanced port V.S.W.R.
at 2495-2690MHz
2.3 max.
Amplitude Imbalance
at 2495-2690MHz
2.0 dB max.
Phase Imbalance
at 2495-2690MHz 180 ＋/− 12 deg
Attenuation
40 dB Min. （824-960MHz）
15 dB Min. （1710-1990MHz）
20 dB Min. （4900-5850MHz）
Impedance 50 : 100
HIGH FREQUENCY PRODUCTS
■ ELECTRICAL CHARACTERISTICS・TYPICAL CHARACTERISTICS
124
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
FI 168P245010
0
0
-10
-20
-30
-40
246810 12
FI 212P245003
FI 168P245023
FI 212P089208
FI 212P089213
Low band
Pass band frequency
2400-2500MHz
Insertion loss
at 2400-2500MHz
0.60 dB max. （25 deg-C）
0.70 dB max. （−40〜＋85 deg-C）
V.S.W.R.
at 2400 – 2500 MHz
2.0max.
Attenuation 20 dB min. （4800-6000MHz）
20 dB min. （7200-7500MHz）
Impedance 50 ohm
High band
Pass band frequency
4900 – 5950 MHz
Insertion loss
at 4900 – 5850 MHz
0.80 dB max. （25 deg-C）
0.95 dB max. （−40〜＋85 deg-C）
V.S.W.R.
at 4900 – 5850 MHz
2.0max.
Attenuation
20 dB min. （1800-2500MHz）
20 dB min. （9800-11900MHz）
*Referece
Impedance 50 ohm
Low band
Pass band frequency
698 – 960 MHz
Insertion loss
at 698 – 960 MHz
0.27 dB max.（＋25 Deg.C）
0.32 dB max.（−40 to ＋85 Deg.C）
V.S.W.R. at
698 – 960 MHz 2.0 max.
Attenuation 13dB min. (1710-2170MHz)
Impedance 50 ohm
High band
Pass band frequency
1710 – 2170 MHz
Insertion loss at
1710 – 2170 MHz
0.45 dB max.（ +25 Deg.C）
0.55 dB max.（−40 to ＋85 Deg.C）
V.S.W.R. at
698 – 960 MHz 2.0 max.
Attenuation
19dB min. （698-960MHz）
Impedance 50 ohm
Low band
Pass band frequency
698 – 960 MHz
Insertion loss
at 698 – 960 MHz
0.27 dB max.（＋25 Deg.C）
0.32 dB max.（−40 to ＋85 Deg.C）
V.S.W.R. at
698 – 960 MHz 2.0 max.
Attenuation 13dB min. (1710-2170MHz)
Impedance 50 ohm
High band
Pass band frequency
1710 – 2170 MHz
Insertion loss at
1710 – 2170 MHz
0.45 dB max.（ ＋25 Deg.C）
0.55 dB max.（−40 to
＋
85 Deg.C）
V.S.W.R. at
698 – 960 MHz 2.0 max.
Attenuation
19dB min. （698-960MHz）
Impedance 50 ohm
0
0
-10
-20
-30
-40
246810 12
01.02.0 3.0
01.02.0 3.0
Low band
Pass band frequency
2400-2500MHz
Insertion loss
at 2400-2500MHz
0.40 dB max. （25 deg-C）
0.50 dB max. （−40〜＋85 deg-C）
V.S.W.R.
at 2400 – 2500 MHz
2.0 max.
Attenuation 20 dB min. （4900-5850MHz）
15 dB min. （5850-8500MHz）
Impedance 50 ohm
High band
Pass band frequency
4900 – 5850 MHz
Insertion loss
at 4900 – 5850 MHz
0.60 dB max. （25 deg-C）
0.70 dB max. （−40〜＋85 deg-C）
V.S.W.R.
at 4900 – 5850 MHz
2.0 max.
Attenuation 20 dB min. （2400-2500MHz）
Impedance 50 ohm
Low band
Pass band frequency
2400-2500MHz
Insertion loss
at 2400-2500MHz
0.5 dB max. （25 deg-C）
0.7 dB max. （−30〜＋85 deg-C）
V.S.W.R. 2.0 max.
Attenuation
14 dB min. （4900-5150MHz）
20 dB min. （5150-5350MHz）
14 dB min. （5470-5825MHz）
High band
Pass band frequency 1
4900-5150MHz
Pass band frequency 2
5150-5350MHz
Pass band frequency 3
5470-5825MHz
Insertion loss at
pass band 1
0.7 dB max. （25 deg-C）
0.9 dB max. （−30〜＋85 deg-C）
Insertion loss at
pass band 2
0.6 dB max. （25 deg-C）
0.8 dB max. （−30〜＋85 deg-C）
Insertion loss at
pass band 3
0.9 dB max. （25 deg-C）
1.0 dB max. （−30〜＋85 deg-C）
V.S.W.R. 2.0 max. （band-1.-2）
2.5 max. （band-2）
Attenuation 20 dB min. （2400-2500MHz）
FI 212P085909
Low band
Pass band frequency
698–960 MHz
Insertion loss
at 698 – 960 MHz
0.70 dB max.（+25 deg-.C）
0.75 dB max.（-30〜+85 deg-.C）
V.S.W.R.
at 698 – 960 MHz
1.6 max.
Attenuation
19dB min. （1558–1570MHz）
20dB min. （1570–1580MHz）
19dB min. （1580–1610MHz）
Impedance 50 ohm
High band
Pass band frequency 1
1558–1570MHz
Pass band frequency 2
1570–1580MHz
Pass band frequency 3
1580–1610MHz
Insertion loss
at 1558 – 1570 MHz
0.75 dB max.（+25 deg-.C）
0.85 dB max.（-30〜+85 deg-.C）
Insertion loss
at 1570 – 1580 MHz
0.70 dB max.（+25 deg-.C）
0.80 dB max.（-30〜+85 deg-.C）
Insertion loss
at 1580 – 1610 MHz
0.70 dB max.（+25 deg-.C）
0.80 dB max.（-30〜+85 deg-.C）
V.S.W.R.
at 1558 – 1570 MHz
1.6 max.
V.S.W.R.
at 1570 – 1580 MHz
1.6 max.
V.S.W.R.
at 1580 – 1610 MHz
1.6 max.
Attenuation 35dB min. （698–824MHz）
42dB min. （824–894MHz）
25dB min. （894–960MHz）
Impedance 50 ohm
0.5
0
-10
-20
-30
-40
-50
-60 1.01.5 2.02.5
HIGH FREQUENCY PRODUCTS
■ ELECTRICAL CHARACTERISTICS・TYPICAL CHARACTERISTICS
125
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
FI 212P085912
Low band
Pass band frequency
698–960 MHz
Insertion loss
at 698 – 960 MHz
0.70 dB max.（+25 deg-.C）
0.75 dB max.（-30〜+85 deg-.C）
V.S.W.R.
at 698 – 960 MHz
1.6 max.
Attenuation
19dB min. （1558–1570MHz）
20dB min. （1570–1580MHz）
19dB min. （1580–1610MHz）
Impedance 50 ohm
High band
Pass band frequency 1
1558–1570MHz
Pass band frequency 2
1570–1580MHz
Pass band frequency 3
1580–1610MHz
Insertion loss
at 1558 – 1570 MHz
0.75 dB max.（+25 deg-.C）
0.85 dB max.（-30〜+85 deg-.C）
Insertion loss
at 1570 – 1580 MHz
0.70 dB max.（+25 deg-.C）
0.80 dB max.（-30〜+85 deg-.C）
Insertion loss
at 1580 – 1610 MHz
0.70 dB max.（+25 deg-.C）
0.80 dB max.（-30〜+85 deg-.C）
V.S.W.R.
at 1558 – 1570 MHz
1.6 max.
V.S.W.R.
at 1570 – 1580 MHz
1.6 max.
V.S.W.R.
at 1580 – 1610 MHz
1.6 max.
Attenuation
35dB min. （698–824MHz）
42dB min. （824–894MHz）
25dB min. （894–960MHz）
Impedance 50 ohm
0.5
0
-10
-20
-30
-40
-50
-60 1.01.5 2.02.5
FI 168T155021
Pass band frequency
900-2200MHz
Insertion loss at
pass band
2.0 dB max.（25 deg-C）
2.3 dB max.（-30〜+85 deg-C）
V.S.W.R. at pass band
2.3 max.
Phase balance
at pass band 180 ＋/− 20 deg
Amplitude Imbalance
at pass band
＋/−2 dB max.
Impedance 50 : 75
FI 168P157519
FI 325P120057
0.01.0 2.03.0
0
-10
-20
-40
-30
-50
0123
0
-20
-10
-30
-60
-40
-50
-70
㻓㻑㻘
㻓㻑㻓
㻐㻓㻑㻘
㻐㻔㻑㻓
㻐㻔㻑㻘
㻐㻕㻑㻓
㻐㻕㻑㻘
㻐㻖㻑㻓
㻗㻑㻓
㻖㻑㻘
㻖㻑㻓
㻕㻑㻘
㻕㻑㻓
㻔㻑㻘
㻔㻑㻓
㻤㼐㼓㼏㼌㼗㼘㼇㼈䠭㼇㻥䠯 㻶㼇㼖㻕㻔䠭㼇㻥䠯
㻶㼖㼖㻔㻔䠭㻹㻶㻺㻵䠯
㻳㼋㼄㼖㼈䠭㼇㼈㼊䠯
㻔㻑㻓㻔㻑㻘 㻕㻑㻓㻕㻑㻘
㻓㻑㻘
㻖
㻕
㻔
㻓
㻐㻔
㻐㻕
㻐㻖
㻕㻔㻓
㻕㻓㻓
㻔㻜㻓
㻔㻛㻓
㻔㻚㻓
㻔㻙㻓
㻔㻘㻓
㻔㻑㻓㻔㻑㻘 㻕㻑㻓㻕㻑㻘
㻤㼐㼓㼏㼌㼗㼘㼇㼈
㻳㼋㼄㼖㼈
㻶㼖㼖㻔㻔
㻶㼇㼖㻕㻔
Low band
Pass band frequency
900 – 1450 MHz
Insertion loss
at 900 – 1450 MHz
4.00 dB max.（+25 deg-.C）
4.40 dB max.（-40〜+85 deg-.C）
Ripple
at 900 – 1450 MHz
3.0 dB max.（+25 deg-.C）
3.4 dB max.（-40〜+85 deg-.C）
V.S.W.R.
at 900 – 1450 MHz
2.2 max.
Attenuation
44dB min. （1650–2200MHz）（+25 deg-.C）
40dB min. （1650–2200MHz）（-40〜+85 deg-.C）
45dB min. （1650MHz）（+25 deg-.C）
41dB min. （1650MHz）（-40〜+85 deg.-C）
Impedance 50 ohm
High Band
Pass band frequency
1650 – 2200 MHz
Insertion loss
at 1650 – 2200 MHz
4.00 dB max.（+25 deg-.C）
4.40 dB max.（-40〜+85 ｄeg-.C）
Ripple
at 1650 – 2200 MHz
3.0 dB max.（+25 deg-.C）
3.2 dB max.（ -40 to +85 Deg.C）
V.S.W.R.
at 1650 – 2200 MHz
2.25 max.
Attenuation
44dB min. （900–1450MHz）（+25 deg-.C）
40dB min. （900–1450MHz）（ -40〜+85 deg-.C）
45dB min. （1450MHz）（+25 deg-.C）
41dB min. （1450MHz）（-40〜+85 deg-.C）
Impedance 50 ohm
Low band
Pass band frequency 0
824–960MHz
Pass band frequency 1
1558–1585MHz
Pass band frequency 2
1585–1610MHz
Insertion loss
at 824 – 960 MHz
0.50 dB max.（+25 deg-.C）
0.60 dB max.（-40〜+85 deg-.C）
Insertion loss
at 1558 – 1585 MHz
0.40 dB max.（+25 deg-.C）
0.50 dB max.（-40〜+85 deg-.C）
Insertion loss
at 1585 – 1610 MHz
0.45 dB max.（+25 deg-.C）
0.55 dB max.（-40〜+85 deg-.C）
V.S.W.R.
at 824 – 960 MHz
2.0 max.
V.S.W.R.
at 1558 – 1585 MHz
2.0 max.
V.S.W.R.
at 1585 – 1610 MHz
2.0 max.
Attenuation 13dB min. （2400-2500MHz）
Impedance 50 ohm
High Band
Pass band frequency
2400 – 2500 MHz
Insertion loss
at 2400 – 2500 MHz
0.60 dB max.（+25 deg-.C）
0.70 dB max.（-40〜+85 deg-.C）
V.S.W.R.
at 2400 – 2500 MHz
2.0 max.
Attenuation
12dB min. （824–960MHz）
23dB min. （1558–1585MHz）
20dB min. （1585–1610MHz）
Impedance 50 ohm
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_pack_e-01
MULTILAYER CERAMIC DEVICES (FILTERS / DIPLEXERS / BALUNS)
■PACKAGING
①Minimum Quantity
Type Embossed Tape [pcs]
325P 2000
212B
3000
212L
212C
212P
168B
4000
168L
168T
168D
168P
105B 10000
105L
②Tape Material
●Embossed Tape
●Card Board Cattier Tape
●Taped package
Type (EIA) Thickness
mm (inch) Standard Quantity [pcs]
325P 0.90 typ.（0.035） 2000
212B 0.90 typ.（0.035）
3000
212L 0.45 typ.（0.018）
212C 0.90 typ.（0.035）
212P 0.90 typ.（0.035）
212C-0.5 0.45 typ.（0.018）
212-0.7 0.60 typ.（0.024）
168B 0.45 typ.（0.018）
4000
168L 0.45 typ.（0.018）
168T 0.45 typ.（0.018）
168D 0.45 typ.（0.018）
168P 0.60 typ.（0.024）
105B 0.30 typ.（0.0118） 10000
105L 0.30 typ.（0.0118）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_pack_e-01
③Taping Dimensions
●Embossed tape 0.315 inches wide
(325P Type, 212B Type, 212C Type, 212C-0.7 Type）
●Paper tape 0.315 inches wide
(212L Type, 212C-0.5 Type, 168B Type, 168L Type, 168P Type, 168T Type, 168DType, 105B Type, 105L Type）
Type（EIA） Chip cavity Insertion Pitch Tape Thickness max.
A B F K T
325P 2.75±0.2
（0.108±0.008）
3.55±0.2
（0.14±0.008）
4.0±0.1
（0.157±0.004）
1.35
（0.053）
0.3
（0.012）
212B 1.5±0.25
（0.059±0.010）
2.3±0.2
（0.091±0.008）
4.0±0.1
（0.157±0.004）
1.6
（0.063）
0.3
（0.012）
212L 1.55±0.2
（0.061±0.008）
2.3±0.2
（0.091±0.008）
4.0±0.1
（0.157±0.04）
0.65
（0.026）
0.65
（0.026）
212C 1.55±0.2
（0.061±0.008）
2.3±0.2
（0.091±0.008）
4.0±0.1
（0.157±0.004）
1.6
（0.063）
0.3
（0.012）
212C-0.5
212C-0.7 1.55±0.2
（0.061±0.008）
2.3±0.2
（0.091±0.008）
4.0±0.1
（0.157±0.004）
1.3
（0.051）
0.3
（0.012）
212P 1.55±0.2
（0.061±0.008）
2.3±0.2
（0.091±0.008）
4.0±0.1
（0.157±0.004）
1.6
（0.063）
0.3
（0.012）
168B 1.00±0.05
（0.039±0.002）
1.80±0.05
（0.071±0.002）
4.0±0.1
（0.157±0.004）
0.55
（0.022）
0.55
（0.022）
168L 1.00±0.05
（0.039±0.002）
1.80±0.05
（0.071±0.002）
4.0±0.1
（0.157±0.004）
0.55
（0.022）
0.55
（0.022）
168T 1.00±0.05
（0.039±0.002）
1.80±0.05
（0.071±0.002）
4.0±0.1
（0.157±0.004）
0.55
（0.022）
0.55
（0.022）
168D 1.00±0.05
（0.039±0.002）
1.80±0.05
（0.071±0.002）
4.0±0.1
（0.157±0.004）
0.55
（0.022）
0.55
（0.022）
168P 0.95±0.05
（0.037±0.002）
1.80±0.05
（0.071±0.002）
4.0±0.1
（0.157±0.004）
0.80
（0.031）
0.80
（0.031）
105B 0.62±0.03
（0.024±0.001）
1.12±0.03
（0.044±0.001）
2.0±0.05
（0.079±0.002）
0.45
（0.018）
0.45
（0.018）
105L 0.62±0.03
（0.024±0.001）
1.12±0.03
（0.044±0.001）
2.0±0.05
（0.079±0.002）
0.45
（0.018）
0.45
（0.018）
Unit：mm（inch）
④Leader and Blank Portion
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_pack_e-01
⑤Reel size
⑥Top Tape Strength
The top tape requires a peel-off force of 0.1～0.7N in the direction of the arrow as illustrated below.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_reli_e-01
MULTILAYER CERAMIC DEVICES (FILTERS / DIPLEXERS / BALUNS)
■RELIABILITY DATA
1. Operating Temperature Range
Specified Value －30～＋85℃
2. Storage Temperature Range
Specified Value －30～＋85℃
Test Methods and
Remarks ※Note : －20 to +40℃ in taped packaging
3. Resistance to Flexure of Substrate
Specified Value No mechanical damage.
Test Methods and
Remarks
Warp : 2mm
Testing board : Glass epoxy-resin substrate
Thickness : 0.8mm
4. Adhesion of Electrode
Specified Value Characteistics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Applied force : 5N
Duration : 10 sec.
5. Solderability
Specified Value 75% or more of immersed surface of terminal electrode shall be covered with fresh solder.
Test Methods and
Remarks
Solder temperature : 230±5℃
Duration : 4±1 sec
Preconditioning : Immersion into flux.
Immersion and Removal speed : 25mm/sec.
6. Resistance to Solder Heat
Specified Value Characterstics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Preheating : 150℃ for 2 min.
Solder temperature : 260±5℃
Duration : 5±0.5 sec.
Preconditioning : Immersio into flux.
mmersion and Removal speed : 25mm/sec.
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_reli_e-01
7. Thermal Shock
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
According to JIS C 0025.
Conditions for 1 cycle
Step Temperature (℃) Duration (min)
1 －40±3 30±3
2 Room Temperature Within 3
3 85±2 30±3
4 Room Temperature Within 3
Nuber of cycles : 100
Mounting method : Soldering onto PC board.
Recovery : 2 to 3hrs of recovery under the standard condition after the remoal from test chamber.
8. Humidity (steady state)
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Temperature : ＋40±2℃
Humidity : 90～95%RH
Duation : 96hrs
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
9. High temperature life test
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Temperature : ＋85±2℃
Duration : 96hrs
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
10. Low temperature life test
Specified Value Characteristics : shall satisfy the electrical characteristics.
Appearance : No significant abnormality.
Test Methods and
Remarks
Temperature : －40±2℃
Duration : 96hrs
Recovery : 2 to 3hrs of recovery under the standard condition after the removal from test chamber.
Note on standard condition:
"standard condition" referred to herein is defined as follows :
5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure.
When there are questions concerning measurement result :
In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity and 86 to 106kPa of air
pressure.
Unless otherwise specified, all the tests are conducted under the "standard condition".
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_prec_e-01
MULTILAYER CERAMIC DEVICES (FILTERS / DIPLEXERS / BALUNS)
■PRECAUTIONS
1. PCB Design
Technical
considerations
◆Land pattern design
Land pattern dimension examples
FI325P Type FI212B Type FI212B245025
FI212B190223 FI212L Type
Unit：mm Unit：mm
Unit：mm Unit：mm
FI168T/D Type FI168B/L Type FI168P Type FI212C Type
Unit：mm Unit：mm
Unit：mm Unit：mm
FI212P Type FI212 P3960A4 FI105B/L Type
Unit：mm Unit：mm
Unit：mm
2. Soldering
Technical
considerations
◆Conditions for Reflow soldering (for reference)
【Reflow Profile】
※ Components should be preheated to within 100 to
130℃ from soldering temperature.
※ Assured to be reflow soldering for 2 times.
Note : The above profiles are the maximum allowable
soldering condition, therefore these profiles are
not always recommended.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
chipfilter_prec_e-01
3. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
・ Recommended conditions
Ambient temperature : －20～＋40℃
Humidity : Below 70%RH
The ambient temperature must be kept below 30℃.
Even under ideal storage conditions, the solderbility of electrodes decreases gradually, so filters should be mounted within 6 months
from the time of delivery.
・ The packaging material should be kept where no chlorine or sulfur exists in the air.
Technical
considerations
◆Storage
1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of
terminal electrodes and deterioration of taping/ packaging materials may take place. For this reason, components should be used within 6
months from the time of delivery. If exceeding the above period, please check the solderability before using the filter.
■ Please contact of our offices for further details of specifications.
All of the standard values listed here are subject to change without notice.
Therefore, please check the specifications carefully before use.