ACA2407E 750/870 MHz CATV Power Doubler Line Amplifier Data Sheet - Rev 2.5 FEATURES * 21.3 dB Gain * Very Low Distortion * Excellent 75 Input and Output Match * Stable with High VSWR Load Conditions * Monolithic Design for Consistent Performance Part-to-Part * Low DC Power Consumption * Surface Mount Package Compatible with Automatic Assembly * Low Cost Alternative to Hybrids * Meets Cenelec Standards * Materials set consistent with RoHS Directives. S7 Package 16 Pin Wide Body SOIC with Heat Slug APPLICATIONS * CATV Line Amplifiers, System Amplifiers, Distribution Nodes PRODUCT DESCRIPTION The ACA2407E is a highly linear, monolithic GaAs RF amplifier that has been developed to replace, in new designs, standard CATV hybrid amplifiers. Offered in a convenient surface mount package, the MMIC consists of two pairs of parallel amplifiers that are optimized for exceptionally low distortion and noise figure. A hybrid equivalent that provides flat gain response and excellent input and output return loss over the 40 to 870 MHz CATV downstream band is formed when one ACA2407E is cascaded between two appropriate transmission line baluns. 1A 2A 1B 2B RF Input RF Output ACA2407E Figure 1: Hybrid Application Diagram 04/2012 ACA2407E 1 GND GND 16 2 2A IN 1A OUT 15 3 GND Bias 1A 14 4 1A IN 2A OUT 13 5 1B IN 2B OUT 12 6 I SET Bias 1B 11 7 2B IN 1B OUT 10 8 GND GND 9 Figure 2: Pinout Table 1: Pin Description 2 PIN NAME Ground 9 GND Ground 2AIN Amplifier 2A Input 10 1BOUT Amplifier 1B Output 3 GND Ground 11 Bias 1B 4 1AIN Amplifier 1A Input 12 2BOUT Amplifier 2B Output and Supply 5 1BIN Amplifier 1B Input 13 2AOUT Amplifier 2A Output and Supply 6 ISET Current Adjust 14 Bias 1A 7 2BIN Amplifier 2B Input 15 1AOUT Amplifier 1A Output 8 GND Ground 16 GND Ground PIN NAME 1 GND 2 DESCRIPTION Data Sheet - Rev 2.5 04/2012 DESCRIPTION Bias for 1B Amplifier Bias for 1A Amplifier ACA2407E ELECTRICAL CHARACTERISTICS Table 2: Absolute Mimimum and Maximum Ratings MIN MAX UNIT Supply (pins 12, 13) 0 +28 VDC RF Power at Inputs (pins 4, 5) - +75 dBmV -65 +150 C Soldering Temperature - +260 C Soldering Time - 5.0 Sec PARAMETER Storage Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: 1. Pins 2, 4, 5 and 7 should be AC-coupled. No external DC bias should be applied. 2. Pin 6 should be AC-grounded and/or pulled to ground through a resistor for current control. 3. Pins 11 and 14 are bias feeds for input amplifiers 1A and 1B. No external DC bias should be applied. 4. Pins 10 and 15 receive DC bias directly from pins 11 and 14. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Supply: VDD (pins 12, 13) - +24 - VDC Voltage at ISET (pin 6) - +3 - VDC RF Frequency 40 - 870 MHz Case Temperature -40 - +110 C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. 3 Data Sheet - Rev 2.5 04/2012 ACA2407E Table 4: Electrical Specifications (Ta = +25 C, Vdd = +24 VDC) COMMENTS PARAMETER MIN TYP MAX UNIT Gain (1) 20.4 21.3 22.4 dB Cable Equivalent Slope (1) - 0 - dB Gain Flatness (1) to 870 MHz - 0.2 - dB Noise Figure - 4.0 4.5 dB CTB (1) 77 Channels (2) 110 Channels (3) - -70 -65 -66 - dBc CSO (1) 77 Channels (2) 110 Channels (3) - -66 -60 -64 - dBc XMOD (1) 77 Channels (2) 110 Channels (3) - -62 -60 -60 - dBc 18 22 - dB 75 system Supply Current (IDD) 410 425 440 mA R1 = 75 k, R3 open Refer to Figure 8 Thermal Resistance - 3.1 3.8 IDD Adjust - <1 - (1) Return Loss (Input/Output) (1) Notes: (1) Measured with baluns on the input and output of the device. (2) Parts measured with 77 channels, +56 dBm V power, 13.5 dB tilt at 870 MHz. (3) Parts measured with 110 channels, +52 dBm V power, 13.5 dB tilt at 870 MHz. 4. All specifications as measured on Evaluation Board (see Figures 7 & 8). 4 Data Sheet - Rev 2.5 04/2012 o C/W mA Refer to Figure 8 ACA2407E Table 5: Electrical Specifications at Reduced IDD (Ta = +25 C, Vdd = +24 VDC) PARAMETER TYP TYP UNIT Gain 21.0 21.2 dB CTB (1) 77 Channels (2) -58 -64 dBc CSO (1) 77 Channels (2) -60 -62 dBc XMOD (1) 77 Channels (2) -50 -55 dBc Supply Current (IDD) 360 390 mA R1 (Figure 8) Open Open R3 (Figure 8) 10 k Open COMMENTS Notes: (1) Measured with baluns on the input and output of the device. (2) Parts measured with 77 channels, +56 dBm V power, 13.5 dB tilt at 870 MHz. 5 Data Sheet - Rev 2.5 04/2012 ACA2407E PERFORMANCE DATA Figure 3: Noise Figure vs. Frequency 5 Noise Figure (dB) 4.5 4 3.5 3 2.5 2 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Figure 4: Gain (S21) vs. Frequency 24 23.5 23 Gain (dB) 22.5 22 21.5 21 20.5 20 19.5 19 0 100 200 300 400 500 600 Frequency (MHz) 6 Data Sheet - Rev 2.5 04/2012 700 800 900 1000 ACA2407E Figure 5: Input and Output Return Loss (S11 and S22) vs. Frequency 5 0 Return Loss (dB) -5 -10 -15 -20 -25 -30 S11 S22 -35 -40 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Figure 6: Isolation (S12) vs. Frequency 0 -5 -10 Isolation (dB) -15 -20 -25 -30 -35 -40 -45 -50 0 100 200 300 400 500 600 Frequency (MHz) 7 Data Sheet - Rev 2.5 04/2012 700 800 900 1000 ACA2407E APPLICATION INFORMATION Vt C4 T1 C1 C11 1 GND 2 2AIN 3 GND 4 1AIN 2AOUT 13 1BIN 2BOUT 12 Bias 1B 11 1BOUT 10 GND 9 5 C2 R1* R3* C3 R2 6 ISET 7 2BIN 8 GND GND 16 1AOUT 5 Bias 1A 14 1 IDD Adjust ACA2407E (+24 V) L1 C8 C9 C7 Data Sheet - Rev 2.5 04/2012 L4 L2 Figure 8: Evaluation Board Schematic 8 TVS C12 C13 C5 * Refer to Table 5 for R1, R3 use at lower IDD operation. C10 L3 C15 C6 C14 +24 V RF IN +24 V Figure 7: Evaluation Board Layout T2 RF OUT ACA2407E Table 6: Evaluation Board Parts List REF DESCRIPTION C1, C2, C3, C6, C7, C10, C14 0.01 F Chip Cap C4, C5, C8, C9 QTY VENDOR VENDOR PART NO. 7 MURATA GRM39X7R103K50V 470 pF Chip Cap 4 MURATA GRM39X7R471K50V C11 0.5 pF Chip Cap 1 MURATA GRM36COG0R5C50 C15 47 F Elect. Cap 1 DIGI-KEY CORP P5275-ND C12, C13, R2 Not Used TVS TVS 24 Volt 600 Watt 1 DIGI-KEY CORP SMBJ24ACCCT-ND L1, L2, L3, L4 (4) 680 nH Inductor 4 COILCRAFT 1008CS-681XKBC R1 (5) 75 k Resistor 1 DIGI-KEY CORP P75KGCT-ND R3 (5) 10 k Resistor 1 DIGI-KEY CORP P10KGCT-ND 75 N Male Panel Mount 2 PASTERNACK ENTERPRISES PE4504 Ferrite Core 2 FAIR-RITE 2843002702 MWS WIRE IND. T-2361429-20 1 STANDARD PRINTED CIRC. INC 24VX1AC50 1 INDIUM CORP OF AMERICA 14996Y CONNECTOR (1) T1, T2 (2) (BALUN) Wire Printed Circuit Board INDIUM (3) 300 X 160 Mils Notes: (1) N connector center pin should be approximately 80 mils in length. (2) T1, T2 balun: 6.5 turns thru, as shown in Figure 9. (3) Due to the power dissipation of this device, the printed circuit board should be mounted / attached to a heat sink. (4) 400 mA minimum current rating. (5) Refer to Table 5 for R1, R3 use at lower IDD operation. Metalized traces on P.C.B. Pin #1 Keep leads twisted Wrap-around metal at corners - or vias Figure 9: Balun Drawing 9 Data Sheet - Rev 2.5 04/2012 ACA2407E PACKAGE OUTLINE Figure 10: S7 Package Outline - 16 Pin Wide Body SOIC with Heat Slug 10 Data Sheet - Rev 2.5 04/2012 ACA2407E ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING ACA2407ERS7P2 -40 C to +110 C RoHS Compliant 16 Pin Wide Body SOIC with Heat Slug 3,500 piece tape and reel ACA2407ERS7P0 -40 C to +110 C RoHS Compliant 16 Pin Wide Body SOIC with Heat Slug Ship in Tubes ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 11 Data Sheet - Rev 2.5 04/2012