IDT72T55258L5BBG - Integrated Device Technology

DSC-6157/4

MARCH 2005

IDT72T55248

IDT72T55258

IDT72T55268

2.5V QUADMUX DDR FLOW-CONTROL DEVICE

WITH MUX/DEMUX/BROADCAST FUNCTIONS

8,192 x 40 x 4

16,384 x 40 x 4

32,768 x 40 x 4

IDT and the IDT logo are trademarks of Integrated Device Technology, Inc

COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES

8,192 x 40

16,384 x40

32,768 x 40

8,192 x 40

16,384 x40

32,768 x 40

8,192 x 40

16,384 x40

32,768 x 40

8,192 x 40

16,384 x40

32,768 x 40

FF0/IR0

PAF0

FF1/IR1

PAF1

FF2/ IR2

PAF2

FF3/IR3

PAF3

WEN0

WCS0

WEN1

WCS1

WEN2

WCS2

WEN3

WCS3

WCLK0

WCLK1

WCLK2

WCLK3

D[9:0]

D[19:10]

D[29:20]

D[39:30]

EF0/OR0

PAE0

EF1/OR1

PAE1

EF2/OR2

PAE2

EF3/OR3

PAE3

CEF/COR

Q[39:0]

x10,x20,x40

REN0

RCS0

RCLK0

OE0

Read Control

Queue 0

Queue 1

Queue 2

Queue 3

OS[1:0]

Read Port

Flag Outputs

Write Port

Flag Outputs

Mux Mode

6157 drw01

Queue 0

Data In

Queue 1

Data In

Queue 2

Data In

Queue 3

Data In

Data Out

FEATURES

••

•Choose from among the following memory organizations:

IDT72T55248 - 8,192 words, 40-bits/word maximum, 4 Sequential

Queues total

IDT72T55258 - 16,384 words, 40-bits/word maximum, 4 Sequential

Queues total

IDT72T55268 - 32,768 words, 40-bits/word maximum, 4 Sequential

Queues total

••

•User Selectable Mux / Demux / Broadcast Write Modes

••

•Mux Mode offers 4:1 architecture

- Five discrete clock domains, four write clocks and one read clock

- Four separate write ports, writes data to four independent Queues

- One single read port, capable of reading from any four Queues

- Selectable single or double data rate (SDR/DDR) on read and write

ports

- 10-bit wide write ports in single data rate, doubles internally in double

data rate

- 40-bit wide read port, doubles internally in double data rate,

selectable between the four independent Queues

- Bus Matching on the Read Port x10/x20/x40 (SDR/DDR)

- Fully independent status flags for every Queue

- Composite Empty/Output Ready Flag monitors currently selected

Queue

- Dedicated partial reset for every Queue

••

•Demux Mode offers 1:4 architecture

- Five discrete clock domains, one write clock and four read clocks

- Four separate read ports, read data from four independent Queues

- One single write port, capable of writing to any four Queues

- Selectable single or double data rate on read and write ports

- 10-bit wide read ports in single data rate, doubles internally in double

data rate

- 40-bit wide write port, doubles internally in double data rate,

selectable between the four independent Queues

- Bus Matching on the Write Port x10/x20/x40 (SDR/DDR)

- Fully independent status flags for every Queue

- Composite Full/Input Ready Flag monitors currently selected Queue

- Dedicated partial reset for every Queue

••

•Broadcast Write Mode offers, 1:4 architecture (with simultaneous

writes to all Queues)

- Five discrete clock domains, one write clock and four read clocks

- Four separate read ports, read data from four independent Queues

- One single write port, writes to all four independent Queues

simultaneously

- 10-bit wide read ports in single data rate, doubles internally in double

data rate

- 40-bit wide write port, doubles internally in double data rate

- Selectable single or double data rate on read and write ports

- Bus-Matching on the write port x10/x20/x40 (SDR/DDR)

(See next pages for Demux and Broadcast modes)

FUNCTIONAL BLOCK DIAGRAMS

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Table of Contents

Features ......................................................................................................................................................................................................................1,4

Description ......................................................................................................................................................................................................................6

Pin Configuration .............................................................................................................................................................................................................8

Pin Descriptions..........................................................................................................................................................................................................9-13

Device Characteristics ...................................................................................................................................................................................................15

DC Electrical Characteristics ..........................................................................................................................................................................................16

AC Electrical Characteristics........................................................................................................................................................................................... 17

AC T est Conditions ........................................................................................................................................................................................................18

Functional Description ..............................................................................................................................................................................................20-29

Signal Descriptions ...................................................................................................................................................................................................30-33

JTAG Timing Specifications .......................................................................................................................................................................................36-40

List of Tables

T able 1 — Device Configuration ....................................................................................................................................................................................20

T able 2 — Default Programmable Flag Of fsets................................................................................................................................................................ 20

T able 3 — Status Flags for IDT Standard mode .............................................................................................................................................................23

T able 4 — Status Flags for FWFT mode ........................................................................................................................................................................ 23

T able 5 — I/O V oltage Level Associations.......................................................................................................................................................................24

Table 6 — TSKEW Measurement .................................................................................................................................................................................. 34

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

List of Figures

Figure 1. QuadMux Block Diagram..................................................................................................................................................................................7

Figure 2a. AC Test Load................................................................................................................................................................................................18

Figure 2b. Lumped Capacitive Load, Typical Derating ...................................................................................................................................................18

Figure 3. Programmable Flag Offset Programming Methods ...........................................................................................................................................21

Figure 4. Offset Registers Serial Bit Sequence................................................................................................................................................................22

Figure 5. Bus-Matching Byte Arrangement (Mux, DeMux and Broadcast Mode) .......................................................................................................25-27

Figure 6. Echo Read Clock and Data Output Relationship ..............................................................................................................................................35

Figure 7. Standard JT AG Timing ...................................................................................................................................................................................36

Figure 8. JT AG Architecture ........................................................................................................................................................................................... 37

Figure 9. T AP Controller State Diagram .........................................................................................................................................................................38

Figure 10. Master Reset................................................................................................................................................................................................41

Figure 1 1. Partial Reset for Mux mode...........................................................................................................................................................................42

Figure 12. Partial Reset for Demux mode ......................................................................................................................................................................43

Figure 13. Partial Reset for Broadcast mode ..................................................................................................................................................................44

Figure 14. Write Cycle and Full Flag Timing (Mux mode, IDT Standard mode, SDR to SDR) x10 In to x40 Out .............................................................45

Figure 15. Write Cycle and Full Flag Timing (Broadcast Write mode, IDT Standard mode, SDR to SDR) x10 In to x10 Out ............................................46

Figure 16. Write Cycle and Full Flag Timing (Demux mode, IDT Standard mode, SDR to SDR) x10 In to x10 Out ......................................................... 47

Figure 17. Write Timing (Mux mode, FWFT mode, SDR to SDR) x10 In to x10 Out........................................................................................................48

Figure 18. Write Timing (Broadcast Write mode, FWFT mode, SDR to SDR) x10 In to x10 Out.......................................................................................49

Figure 19. Write Timing (Demux mode, FWFT mode, SDR to SDR) x10 In to x10 Out ...................................................................................................50

Figure 20. Read Cycle, Empty Flag and First Word Latency (Mux mode, IDT Standard mode, SDR to SDR) x10 In to x40 Out.....................................51

Figure 21. Read Timing (Broadcast Write mode, FWFT mode, SDR to SDR) x10 In to x10 Out......................................................................................52

Figure 22. Read Timing (Mux mode, FWFT mode, SDR to SDR) x10 In to x10 Out.......................................................................................................53

Figure 23. Read Timing (Demux mode, FWFT mode, SDR to SDR) x20 In to x10 Out ..................................................................................................53

Figure 24. Read Cycle, Empty Flag and First Word Latency (Demux mode, IDT Standard mode, SDR to SDR) x20 In to x10 Out.................................54

Figure 25. Read Cycle, Empty Flag and First Word Latency (Broadcast Write mode, IDT Standard mode, SDR to SDR) x40 In to x10 Out .................... 55

Figure 26. Composite Empty Flag (Mux mode, IDT Standard mode, SDR to SDR) x10 In to x40 Out............................................................................. 56

Figure 27. Composite Output Ready Flag (Mux mode, FWFT mode, SDR to SDR) x10 In to x40 Out ............................................................................56

Figure 28. Composite Full Flag (Demux mode, IDT Standard mode, SDR to SDR) x20 In to x10 Out ............................................................................57

Figure 29. Composite Input Ready Flag (Demux mode, FWFT mode, SDR to SDR) x20 In to x10 Out ..........................................................................57

Figure 30. Echo Read Clock and Read Enable Operation (Mux/Demux/Broadcast mode, IDT Standard mode, DDR to DDR) x10 In to x10 Out ...........58

Figure 31. Echo RCLK and Echo Read Enable Operation (Mux/Demux/Broadcast mode, FWFT mode, SDR to SDR) ..................................................59

Figure 32. Echo Read Clock and Read Enable Operation (Mux/Demux/Broadcast mode, IDT Standard mode, SDR to SDR) x10 In to x10 Out........... 60

Figure 33. Loading of Programmable Flag Registers (IDT Standard and FWFT modes) ................................................................................................61

Figure 34. Reading of Programmable Flag Registers (IDT Standard and FWFT modes)................................................................................................ 61

Figure 35. Synchronous Programmable Almost-Full Flag Timing (see page for details)...................................................................................................62

Figure 36. Synchronous Programmable Almost-Empty Flag Timing (see page for details)...............................................................................................62

Figure 37. Asynchronous Programmable Almost-Full Flag Timing (see page for details) ................................................................................................63

Figure 38. Asynchronous Programmable Almost-Empty Flag Timing (see page for details) ............................................................................................ 63

Figure 39. Power Down Operation................................................................................................................................................................................64

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

8,192 x 40

16,384 x40

32,768 x 40 10

REN0

RCS0

RCLK0

Q[9:0]

Queue 0

OE0

8,192 x 40

16,384 x40

32,768 x 40 10

REN1

RCS1

RCLK1

Q[19:10]

Queue 1

OE1

8,192 x 40

16,384 x40

32,768 x 40 10

REN2

RCS2

RCLK2

Q[29:20]

Queue 2

OE2

8,192 x 40

16,384 x40

32,768 x 40 10

FF0/ IR0

PAF0

FF1/ IR1

PAF1

FF2/ IR2

PAF2

FF3/ IR3

PAF3

REN3

RCS3

RCLK3

Q[39:30]

Write Port

Flag Outputs

EF0/ OR0

PAE0

EF1/ OR1

PAE1

EF2/ OR2

PAE2

EF3/ OR3

PAE3

CFF/ CIR

Data In

x10,x20,x40

WEN0

WCS0

WCLK0

Write Control

Queue 3

IS[1:0]

Read Port

Flag Outputs

Demux Mode

6157 drw02

D[39:0]

OE3

Queue 0

Data Out

Queue 1

Data Out

Queue 2

Data Out

Queue 3

Data Out

- Fully independent status flags for every Queue

- Composite Full/Input Ready Flag monitors currently selected Queue

- Dedicated partial reset for every Queue

••

•Up to 200MHz operating frequency or 8Gbps throughput in SDR mode

••

•Up to 100MHz operating frequency or 8Gbps throughput in DDR mode

••

•User selectable Single Data Rate (SDR) or Double Data Rate

(DDR) modes on both the write port(s) and read port(s)

••

•All I/O are LVTTL/ HSTL/ eHSTL user selectable

••

•3.3V tolerant inputs in LVTTL mode

••

•ERCLK and EREN Echo outputs on all read ports

••

•Write Chip Select WCS input for each write port

••

•Read Chip Select RCS input for each read port

••

•User Selectable IDT Standard mode (using EF and FF flags) or

FWFT mode (using IR and OR flags)

••

•Composite Full/ Input Ready Flag in Demux and Broadcast

mode

••

•Composite Empty/ Output Ready flag in Mux mode

••

•Independent Programmable Almost Empty and Almost Full flags

per Queue

••

•Dedicated Serial Port for flag programming

••

•Dedicated Partial Reset for each individual Queue

••

•Power Down pin minimizes power consumption

••

•2.5V Supply Voltage

••

•Available in a 324-pin Plastic Ball Grid Array (PBGA)

19mm x 19mm, 1mm Pitch

••

•IEEE 1149.1 compliant JTAG port provides boundary scan

function, or flag programming

••

•Low Power, High Performance CMOS technology

••

•Industrial temperature range (-40°°

°°

°C to +85°°

°°

°C)

FUNCTIONAL BLOCK DIAGRAMS (CONTINUED)

FEATURES (CONTINUED)

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

8,192 x 40

16,384 x40

32,768 x 40

8,192 x 40

16,384 x40

32,768 x 40

8,192 x 40

16,384 x40

32,768 x 40

8,192 x 40

16,384 x40

32,768 x 40

FF0/ IR0

PAF0

FF1/ IR1

PAF1

FF2/ IR2

PAF2

FF3/ IR3

PAF3

Write Port

Flag Outputs

EF0/ OR0

PAE0

EF1/ OR1

PAE1

EF2/ OR2

PAE2

EF3/ OR3

PAE3

CFF/ CIR

Data In

x10,x20,x40

WEN0

WCS0

WCLK0

Write Control

Queue 0

Queue 1

Queue 2

Queue 3

Read Port

Flag Outputs

Broadcast Mode

6157 drw03

REN0

RCS0

RCLK0

Q[9:0]

OE0

REN1

RCS1

RCLK1

Q[19:10]

OE1

REN2

RCS2

RCLK2

Q[29:20]

OE2

REN3

RCS3

RCLK3

Q[39:30]

OE3

Queue 0

Data Out

Queue 1

Data Out

Queue 2

Data Out

Queue 3

Data Out

D[39:0]

FUNCTIONAL BLOCK DIAGRAMS (CONTINUED)

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

DESCRIPTION

The IDT72T55248/72T55258/72T55268 QuadMux flow-control devices

are ideal for many applications where data stream convergence and parallel

buffering of multiple data paths are required. These applications may include

communication and networking systems such as terabit routers, quality of

service (QOS) and packet prioritization routing systems, data bandwidth

aggregation, data acquisition systems, WCDMA baseband systems, and

medical equipments. The QuadMux replaces traditional methods of muxing

multiple data paths at different data rates, in essence reducing external glue

logic. The QuadMux offers three modes of operation, Mux, Demux and

Broadcast. Regardless of the mode of operation there are four internal

Sequential Queues built using IDT FIFO technology and five discrete clock

domains. All four Queues have the same density, and the read and write ports

can operate independently in Single Data Rate (SDR) or Double Data Rate

(DDR). See Figure 1, QuadMux Block Diagram or an outline of the functional

blocks within the device.

The QuadMux device offers a maximum throughput of 8Gbps, with selectable

SDR or DDR data transfer modes for the inputs and outputs. In SDR mode,

the input clock can operate up to 200MHz. Data will transition/latch on the rising

edge of the clock. In DDR mode, the input clock can operate up to 100 MHz,

with data transitioning/latched on both rising and falling edges of the clock. The

advantage of DDR is that it can achieve the same throughput as SDR with only

half the number of bits, assuming the frequency is constant. For example, a

4Gbps throughput in SDR is 100MHz x 40 bits. In DDR mode, it is 100MHz x

20 bits, because two bits transition per clock cycle.

In Mux mode operation a 4:1 architecture is setup, (four input ports to one

output port). Here there are four internal Sequential Queues each with a

dedicated write port. Data can be written into each of the dedicated write ports

totally independent of any other port, each port has its own write clock input and

control enables. There is a single read port that can access any one of the four

Queues. Data is read out of a specific Queue based on the address present

on the output select pins. Only one Queue can be selected and read from at

a time. All input ports are 10 bits wide and the output port has a selectable Bus

Matching x10, x20 or x40 bus widths. A full set of flag outputs per Queue are

available in this mode providing the user with continuous status of each

individual Queue levels.

In Demux mode operation a 1:4 architecture is setup, (one input port to four

output ports). Here there is a single write port that can write data into any one

of four internal Queues. Data is written into a specific Queue based on the

address present on the input select pins. Only one Queue can be selected and

written into at a time. There are four dedicated read ports, one port for each

Queue. Data can be read out of the four Queues through the read port totally

independent of any other port. Each port has its own read clock input and control

enables. The input port has a selectable Bus Matching x10, x20 or x40 bus width

and all the output ports are 10-bits. A full set of flag outputs per Queue are

available in this mode providing the user with continuous status of each individual

Queue levels.

In the Broadcast Write mode the architecture is similar to the Demux mode,

1:4 (one input port to four output ports). However, there is no Queue select

operation in Broadcast mode. Instead data written into the write port is written

to all four internal Queues simultaneously. Again there are four independent

read ports, one port per Queue. In Broadcast mode write operations to all

Queues will be prevented when any one or more of the four Queues are full

or being partially reset. A full set of flag outputs is available in this mode providing

the user with continuous status of each individual Queue levels.

As is typical with most IDT Queues, two types of data timing modes are

available, IDT Standard mode and First Word Fall Through (FWFT) mode. This

affects the device’s operation and also the flag outputs. The device provides four

flag outputs, for each internal Queue. The device also provides composite flags

that represent the full and empty status of the currently selected Queue.

All read ports provide the user with a dedicated Echo Read Enable, EREN

and an Echo Read Clock, ERCLK output. These outputs aid in high-speed

applications where synchronization of the input clock and data of a receiving

device is critical. Otherwise known as “Source Synchronous clocking” the echo

outputs provide tighter synchronization of the data transmitted from the Queue

to the read clock interfacing the Queue outputs.

A master reset input is provided and all setup and configuration pins are

latched with respect to a Master Reset. A Partial Reset is provided for each

internal Queue. When a Partial Reset is performed on a Queue the read and

write pointers of that Queue only are reset to the first memory location. The flag

offset values, timing modes, and initial configurations are retained.

The QuadMux device has the capability of operating its I/Os at either 2.5V

LVTTL, 1.5V HSTL or 1.8V eHSTL levels. A Voltage Reference, VREF input

is provided for HSTL and eHSTL interfaces. The type of I/O is selected by the

IOSEL pin. There are certain inputs that are CMOS based and must be tied to

either VCC or GND. The core supply voltage of the device, VCC is always 2.5V,

however the output pins have a separate supply, VDDQ which can be 2.5V, 1.8V

or 1.5V. The device also offers significant power savings, achieved through the

use of the Power Down input, PD in HSTL/eHSTL mode.

A JTAG test port is provided on the QuadMux device. The Boundary Scan

is fully compliant with IEEE 1149.1 Standard Test Access Port and Boundary

Scan Architecture. The JTAG port can also be used to program the flag offsets.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Res et

Logic

Input

6157 drw04

Input Mux IW[1:0]

8080

RAM

ARRAY 0

8,192 x 40

16,384 x 40

32,768 x 40

RAM

ARRAY 2

8,192 x 40

16,384 x 40

32,768 x 40

RAM

ARRAY 1

8,192 x 40

16,384 x 40

32,768 x 40

RAM

ARRAY 3

8,192 x 40

16,384 x 40

32,768 x 40

Output Mux

OE0/1/2/3

Q[39:0] (x10, x20, x40)

OW[1:0]

RCS0/1/2/3

JTAG Control

(Boundary Scan)

Status Flag

Logic

Read Control

Logic

Write Control

Logic

Read Control

Logic

Write Control

Logic

Status Flag

Logic

WDDR

WEN2

WCS2

WCLK2

RDDR

REN2

RCS2

RCLK2

WDDR

WEN3

WCS3

WCLK3

RDDR

REN3

RCS3

RCLK3

PAF2

FF2/IR2

PAE2

EF2/OR2

PAF3

FF3/IR3

PAE3

EF3/OR3

TCK

TRST

TMS

TDI

TDO

Composite

Flags

CEF/

COR

CFF/

CIR

MRS PRS0/1/2/3

Status Flag

Logic

Read Control

Logic

Write Control

Logic

Read Control

Logic

Write Control

Logic

Status Flag

Logic

Programmable

Flag Control

WDDR

WEN0

WCS0

WCLK0

RDDR

REN0

RCS0

RCLK0

WDDR

WEN1

WCS1

WCLK1

RDDR

REN1

RCS1

RCLK1

PAF0

FF0/IR0

PAE0

EF0/OR0

PAF1

FF1/IR1

PAE1

EF1/OR1

D[39:0] (x10, x20, x40)

SCLK

SWEN

SREN

SDO

FWFT/SI

FSEL[1:0]

PFM

Figure 1. QuadMux Block Diagram

NOTES:

1. This block diagram only shows the architecture for Queue 0. There are a total of four Queues inside this device all with the identical architecture.

2. *Denotes dedicated signal for each internal Queue inside the device.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

WEN2

WCS3

GND

VCC

D39 Q33

Q36

PAF3 OS0 Q35REN2RCS1

VDDQ

VCC VCC

VCC GND VDDQ

VDDQ VDDQ VDDQ

D0 D1

D13

WCLK0

WCLK1

D38

MD0

GND

GND GND

GND

PRS0

VCC

GND

VDDQ OE3

OE0

PRS3VREF MRS

D23

OE1OE2

FWFT/SI

Q12

Q15

12 34 56 78910111213141516

A1 BALL PAD CORNER

OW1

MD1

D24

D27

D30

D33

D36

GND

VDDQ

WCLK2

WCLK3

D26

D29

D32

D35

D11

D14

D16

D18

D20

D25

D22

D28

D31

D34

D37 Q30

Q18

EREN1

EREN2

Q21

Q24

Q27

TDI SREN

SCLK

D12

D15

D17

D19

D21

D4 D5 FSEL0

WDDR

D9 OW0

FSEL1 VDDQ

IW0 GND

VCC TRST

IW1 TMS

TCK

GND

PFM VCC

IOSEL VDDQ

GND GND

VCC VDDQVDDQ VDDQ

VDDQ

VCC

SWEN

D10

RDDR VCC

PRS1PRS2

6157 drw05

IS1

GND

VCC

Q38

RCLK1

OS1 RCS2RCLK2RCLK3

REN3

RCS0

PAE3RCS3REN1REN0

17 18

ERCLK0

ERCLK1

Q37

Q34

Q10

Q13

Q32

Q16

Q19

Q20

Q23

Q26

Q29

TDO

SDO

EREN0

EREN3

Q22

Q25

Q28

Q31

Q11

Q14

Q17

ERCLK2

ERCLK3

RCLK0

Q39

VCCVCC

VCC VDDQ

VCC GND

VCC VDDQ VDDQ

VDDQ

GNDGND

VCC GNDGND GND

GND GND VDDQ

GND

GNDGND

VCC GNDGND GND

GND GND VDDQ

GND

GND GND

GND

VCC GND GND GND GND VDDQGND

GND

VCC GND GND

GND VDDQ

GNDVCCVCC VDDQ

VCC

VCC GND VDDQ

VDDQ VDDQ

GNDGND

VCC

GNDGND

VCC

GNDGND

VCC

GNDGND

VCC

GND VDDQ

GND

GND VDDQ

GND

GND VDDQ

GND

GND VDDQ

GND

WEN3

WEN0WEN1

WCS0WCS1WCS2

IS0 PAE0EF0/OR0PAE1PAE2

PAF0CEF/

COR

FF0/IR0PAF1CFF/CIR PAF2FF2/IR2

FF3/IR3

FF1/IR1

EF1/OR1EF2/OR2

EF3/OR3

PBGA (BB324-1, order code: BB)

TOP VIEW

PIN CONFIGURATION

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

CEF/COR Composite Empty/ HSTL-LVTTL If Mux mode is selected this flag will represent the exact status of the current Queue being read

(U6) Composite Output OUTPUT(2) without the user having to observe the empty flag corresponding to the current Queue.

Ready Flag If Demux or Broadcast mode is selected this output is not used and can be left floating.

CFF/CIR Composite Full/ HSTL-LVTTL If Mux mode is selected this output is not used and can be left floating.

(T6) Composite Input OUTPUT(2) If Demux mode is selected this flag will represent the exact status of the current Queue being written

Ready flag without the user having to observe the full flag corresponding to the current Queue.

If Broadcast mode is selected this flag goes active when any one of the four Queues goes full and

inactive when all four Queues are not full.

D[39:0] Data Input Bus HSTL-LVTTL These are the data inputs for the device. Data is written into the part using the respective write port

(See Pin No. INPUT clock(s) and enable(s). If Demux or Broadcast mode is selected this is a single data input bus providing

table for details) Bus-Matching of x10, x20 or x40 bits. If Mux mode is selected these inputs become four separate

busses to the four separate Queues. D[9:0] is Queue[0], D[19:10] is Queue[1], D[29:20] is Queue[2],

D[39:30] is Queue[3]. Any unused inputs should be tied to GND. Note the inputs are 3.3V tolerant

in LVTTL mode.

EF0/1/2/3/- Empty Flags 0/1/2/3 HSTL-LVTTL This is the Empty Flag (Standard IDT mode) or Output Ready Flag (FWFT mode) corresponding

OR0/1/2/3 or Output Ready OUTPUT(2) to each of the four Queues on the read port. EF indicates whether or not the Queue is empty.

(See Pin No. Flags 0/1/2/3 OR indicates whether or not there is valid data available at the outputs. These flags always represent

table for details) the status of the corresponding Queue at all times in every mode.

ERCLK0 Echo Read Clock 0 HSTL-LVTTL If Mux mode is selected this is the only echo clock output available for the read port.

(R18) OUTPUT(2) If Demux or Broadcast mode is selected this is the echo read clock output for Queue 0.

Echo read clock always follows RCLK0 with an associated delay.

ERCLK1/2/3 Echo Read Clock HSTL-LVTTL If Mux mode is selected these clock outputs are inactive and can be left floating.

(ERCLK1-T18 1/2/3 OUTPUT(2) If Demux or Broadcast mode is selected these are the echo read clock outputs for Queues 1, 2, and

ERCLK2-U18 3 respectively.

ERCLK3-V18) ERCLK1, ERCLK2 and ERCLK3 always follow RCLK1, RCLK2 and RCLK3 respectively.

EREN0 Echo Read Enable 0 HSTL-LVTTL If Mux mode is selected this is the echo read enable output for the read port.

(J17) OUTPUT(2) If Demux or Broadcast mode is selected this is the echo read enable input for Queue 0.

Echo Read Enable is synchronous to the RCLK input and is active when a read operation has occurred

and a new word has been placed onto the data output bus.

EREN1/2/3 Echo Read Enable HSTL-LVTTL If Mux mode is selected these outputs are inactive and can be left floating.

(EREN1-J16 1/2/3 OUTPUT(2) If Demux or Broadcast mode is selected these are the echo read enable outputs for Queues 1, 2 and

EREN2-K16 3 respectively.

EREN3-K17) Echo Read Enable is synchronous to the RCLK input and is active when a read operation has occurred

and a new word has been placed onto the data output bus.

FF0/1/2/3- Full Flags 0/1/2/3 or HSTL-LVTTL This is the Full Flag (Standard IDT mode) or Input Ready Flag (FWFT mode) corresponding to

IR0/1/2/3 Input Ready Flags OUTPUT(2) each of the four Queues on the write port. FF indicates whether or not the Queue is full.

(See Pin table) 0/1/2/3 IR indicates whether or not there is valid space for writing data onto the Queue.

FSEL [1:0] Flag Select HSTL-LVTTL During master reset, the FSEL pins are used to select one of four default PAE and PAF offsets.

(FSEL1-C5 INPUT All four internal Queues are programmed to the same PAE/PAF offset value. Values are: 00 = 7;

FSEL0-B6) 01 = 63; 10 = 127; 11 = 1023

FWFT/SI First Word Fall HSTL-LVTTL During master reset, FWFT is HIGH then the First Word Fall Through mode is selected. If FWFT

(B16) Through/ Serial INPUT is LOW the IDT Standard mode is selected. After master reset this pin is used for the serial data

Input input for the programming of the PAE and PAF flags offset registers.

IOSEL I/O Select CMOS(1) This input determines whether the inputs will operate in LVTTL or HSTL/eHSTL mode. If IOSEL

(D5) INPUT pin is HIGH, then all inputs and outputs that are designated "LVTTL or HSTL" in this section will be

set to HSTL. If IOSEL is LOW then LVTTL is selected. This signal must be tied to either VCC or

GND for proper operation.

IS[1:0] Input Select HSTL-LVTTL If Mux or Broadcast mode is selected these inputs are not used and should be tied to GND.

(IS1-V1 INPUT If Demux mode is selected these inputs select one of the four Queues to be written into on the write

IS0-V2) port. The address on the input select pins is setup with respect to the rising edge of WCLK0.

PIN DESCRIPTIONS

Symbol & Name I/O TYPE Description

Pin No.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

PIN DESCRIPTIONS (CONTINUED)

IW[1:0] Input Width CMOS(1) In Demux or Broadcast, these pins are used during master reset to select the input bus size for the

(IW1-C12 INPUT device. The values are: 00 = x10; 01 = x20; 10 = x40. 11 = Restricted. In Mux mode these pins must

IW0-C8) be tied to GND.

MD[1:0] Mode Pin CMOS(1) This mode selection pin used during Master Reset to select the mode of the Queue. The values are:

(MD1-B5 INPUT 00 = Demux; 10 = Mux; 01 = Broadcast Write; 11 = Restricted.

MD0-B4)

MRS Master Reset HSTL-LVTTL This input provides a full device reset. All set-up pins are sampled based on a master reset operation.

(A5) INPUT Read and write pointers will be reset to the first location memory. All flag offsets are cleared and

reset to default values determined by FSEL[1:0].

OE0 Output Enable 0 HSTL-LVTTL If Mux mode is selected this is the Output Enable for the read port. All data output pins will be placed

(A13) INPUT into High Impedance if this pin is HIGH.

If Demux or Broadcast mode is selected this is the output enable pin for Queue 0. All data output

pins of Queue 0 will be placed into High Impedance if this pin is HIGH. This input is asynchronous.

OE1-(A14) Output Enable 1/2/3 HSTL-LVTTL If Mux mode is selected these inputs are ignored and can be tied HIGH.

OE2-(A15) INPUT If Demux or Broadcast mode is selected these are the output enable pins Queues 1, 2 and 3

OE3-(A16) respectively. All data outputs on Queue 1, Queue 2 and Queue 3 will be in High-Impedance if the

respective output enable pin is High. These inputs are asynchronous.

OS[1:0] Output Select HSTL-LVTTL If Mux mode is selected these inputs select one of the four Queues to be read from on the read port.

(OS1-V11 INPUT The address on the output select pins is setup with respect to the rising edge of RCLK0.

OS0-T12) If Demux or Broadcast mode is selected these inputs are not used and should be tied to GND.

OW[1:0] Output Width HSTL-LVTTL If Mux mode is selected, this pin is used during master reset to select the output word width bus

(OW1-B8 INPUT size for the device. The values are: 00 = x10; 01 = x20; 10 = x40; 11 = Restricted.

OW0-C6) If Demux or Broadcast mode is selected the output word width will be x10. These pins are not used

and must be tied to GND.

PAE0-(V3) Programmable HSTL-LVTTL This is the programmable almost empty flag that can be used to pre-indicate the empty boundary

PAE1-(V5) Almost Empty Flag OUTPUT(2) of each Queue. The PAE flags can be set to one of four default offsets determined by the state of

PAE2-(V7) 0/1/2/3 FSEL0 and FSEL1 during master reset. The PAE offset values can also be written and read from

PAE3-(U10) serially by either the JTAG port or the serial programming pins (SCLK, FWFT/SI, SDO, SWEN,

SREN). This flag can operate in synchronous or asynchronous mode depending on the state of the

PFM pin during master reset.

PAF0-(U4) Programmable HSTL-LVTTL This is the programmable almost full flag that can be used to pre-indicate the full boundary of each

PAF1-(T5) Almost Full Flag OUTPUT(2) Queue. The PAF flags can be set to one of four default offsets determined by the state of FSEL0 and

PAF2-(T7) 0/1/2/3 FSEL1 during master reset. The PAF offset values can also be written and read from serially by

PAF3-(T11) either the JTAG port or the serial programming pins (SCLK, FWFT/SI, SDO, SWEN, SREN). This

flag can operate in synchronous or asynchronous mode depending on the state of the PFM pin

during master reset.

PD Power Down HSTL-LVTTL This input provides considerable power saving in HSTL/eHSTL mode. If this pin is low, the input

(B12) INPUT level translators for all the data input pins, clocks and non-essential control pins are turned off.

When PD is brought high, power-up sequence timing will have to be followed to before the inputs

will be recognized. It is essential that the user respect these conditions when powering down the

part and powering up the part, so as to not produce runt pulses or glitches on the clocks if the clocks

are free running. PD does not provide any power consumption savings when the inputs are

configured for LVTTL

PFM Programmable Flag CMOS(1) During master reset, a HIGH on PFM selects synchronous PAE/PAF flag timing, a Low during

(D4) Mode INPUT master reset selects asynchronous PAE/PAF flag timing. This pin controls all PAE/PAF flag outputs.

PRS0-(A6) Partial Reset HSTL-LVTTL These are the partial reset inputs for each internal Queue. The read, write, flag pointers, and output

PRS1-(A7) 0/1/2/3 registers will all be set to zero when partial reset is activated. During partial reset, the existing mode

PRS2-(A8) (IDT or FWFT), input/output bus width and rate mode, and the programmable flag settings are all

PRS3-(A12) retained.

Symbol & Name I/O TYPE Description

Pin No.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

PIN DESCRIPTIONS (CONTINUED)

Q[39:0] Data Output Bus HSTL-LVTTL These are the data outputs for the device. Data is read from the part using the respective read

See Pin No. OUTPUT(2) port clock(s) and enable(s). If Mux mode is selected this is a single data output bus providing Bus-

table for details) Matching of x10, x20 or x40 bits. If Demux or Broadcast mode is selected these outputs become four

separate busses from the four separate Queues. Q[9:0] is Queue[0], Q[19:10] is Queue[1], Q[29:20]

is Queue[2], Q[39:30] is Queue[3]. Any unused outputs should be left floating. Note, that the outputs

are NOT 3.3V tolerant.

RCLK0 Read Clock 0 HSTL-LVTTL If Mux mode is selected this is the clock input for the read port. All read port operations will be

(V17) INPUT synchronous to this clock input.

If Demux or Broadcast mode is selected this is the read clock input for Queue 0. All read port operations

on Queue 0 will be synchronous to this clock input.

RCLK1-(V16) Read Clock 1/2/3 HSTL-LVTTL If Mux mode is selected these clock inputs are ignored and if unused can be tied to GND.

RCLK2-(V15) INPUT If Demux or Broadcast mode is selected these are the read clock inputs for Queues 1, 2, and 3

RCLK3-(V14) respectively. All read port operations on Queue 1, Queue 2 and Queue 3 will be synchronous to clock

inputs RCLK1, RCLK2 and RCLK3 respectively.

RCS0 Read Chip Select 0 HSTL-LVTTL If Mux mode is selected this is the read chip select input for the read port. All read operations will occur

(U13) INPUT synchronous to the RCLK0 input provided that REN0 and RCS0 are LOW.

If Demux or Broadcast mode is selected this is the read chip select input for Queue 0. All read operations

on Queue 0 will occur synchronous to the RCLK0 input provided that REN0 and RCS0 are LOW.

RCS1-(T13) Read Chip Select HSTL-LVTTL If Mux mode is selected these inputs are ignored and can be tied HIGH.

RCS2-(V12) 1/2/3 INPUT If Demux or Broadcast mode is selected these are the read chip select inputs for Queues 1, 2 and

RCS3-(U12) 3 respectively. All read operations on Queue 1, Queue 2 and Queue 3 will occur synchronous to the

RCLK1, 2 and 3 input respectively, provided that the corresponding read enable and read chip

select inputs are LOW.

RDDR Read Port DDR CMOS(1) During master reset, this pin selects the output port to operate in DDR or SDR format. If RDDR is HIGH,

(B7) INPUT then a word is read on the rising and falling edge of the appropriate RCLK0, 1, 2 and 3 input. If RDDR

is LOW, then a word is read only on the rising edge of the appropriate RCLK0, 1, 2 and 3 inputs.

REN0 Read Enable 0 HSTL-LVTTL If Mux mode is selected this is the read enable input for the read port. All read operations will occur

(U15) INPUT synchronous to the RCLK0 clock input provided that REN0 and RCS0 are LOW.

If Demux or Broadcast mode is selected this is the read enable input for Queue 0. All read operations

on Queue 0 will occur synchronous to the RCLK0 input provided that REN0 and RCS0 are LOW.

REN1-(U14) Read Enable 1/2/3 HSTL-LVTTL If Mux mode is selected these inputs are ignored and can be tied HIGH.

REN2-(T14) INPUT If Demux or Broadcast mode is selected these are the read enable inputs for Queues 1, 2 and 3

REN3-(V13) respectively. All read operations on Queue 1, Queue 2 and Queue 3 will occur synchronous to the

RCLK0, 1, 2 and 3 inputs respectively, provided that the corresponding read enable and read chip

select inputs are LOW.

SCLK Serial Clock HSTL-LVTTL Serial clock for writing and reading the PAE and PAF offset registers. On the rising edge of each

(B14) INPUT SCLK, when SWEN is LOW, one bit of data is shifted from the FWFT/SI pin into the PAE and PAF offset

registers. On the rising edge of each SCLK, when SREN is LOW, one bit of data is shifted out of the

PAE and PAF offset registers. The reading of the PAE and PAF offset registers are non-destructive.

If programming of the PAE/PAF offset registers is done via the JTAG port, this input must be tied to VCC.

SDO Serial Data Output LVTTL This output is used to read data from the programmable flag offset registers. It is used in conjunction

(C17) OUTPUT(2) with the SREN and SCLK signals.

SREN Serial Read Enable HSTL-LVTTL When SREN is brought LOW before the rising edge of SCLK, the contents of the PAE and PAF

(B15) INPUT offset registers are copied to a serial shift register. While SREN is maintained LOW, on each rising

edge of SCLK, one bit of data is shifted out of this serial shift register through the SDO output pin.

If programming of the PAE/PAF offset registers is done via the JTAG port, this input must be tied to VCC.

SWEN Serial Write Enable HSTL-LVTTL On each rising edge of SCLK when SWEN is LOW, data from the FWFT/SI pin is serially loaded

(C16) INPUT into the PAE and PAF registers. If programming of the PAE/PAF offset registers is done via the

JTAG port, this input must be tied to VCC. On each clock, data is shifted into and through the actual

PAE and PAF registers, so the value of the registers is changed on each clock

Symbol & Name I/O TYPE Description

Pin No.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

TCK(3) JTAG Clock HSTL-LVTTL Clock input for JTAG function. One of four terminals required by IEEE Standard 1149.1-1990. Test

(C13) INPUT operations of the device are synchronous to TCK. Data from TMS and TDI are sampled on the

rising edge of TCK and output TDO change on the falling edge of TCK. If the JTAG function is not used

this signal needs to be tied to GND.

TDI(3) JTAG Test Data HSTL-LVTTL One of four terminals required by IEEE Standard 1149.1-1990. During the JTAG boundary scan

(B13) Input INPUT operation, test data is serially loaded via the TDI on the rising edge of TCK to either the Instruction

TDI HIGH if left unconnected.

TDO(3) JTAG Test Data HSTL-LVTTL One of four terminals required by IEEE Standard 1149.1-1990. During the JTAG boundary scan

(B17) Output OUTPUT operation, test data is scanned to the TDO output on the falling edge of TCK from either the Instruction

except when shifting, while in SHIFT-DR and SHIFT-IR controller states.

TMS(3) JTAG Mode Select HSTL-LVTTL TMS is a serial input pin. One of four terminals required by IEEE Standard 1149.1-1990. TMS directs

(C14) INPUT the device through its TAP controller states sampled on the rising edge of TCK. An internal pull-up

resistor forces TMS HIGH if left unconnected.

TRST(3) JTAG Reset HSTL-LVTTL TRST is an asynchronous reset pin for the JTAG controller. The JTAG TAP controller is automatically

(C15) INPUT reset upon power-up. If the TAP controller is not properly reset then the Queue outputs will always

be in high-impedance. If the JTAG function is used but the user does not want to use TRST, then TRST

can be tied with MRS to ensure proper Queue operation. If the JTAG function is not used then this

signal needs to be tied to GND. An internal pull-up resistor forces TRST HIGH if left unconnected.

WCLK0 Write Clock 0 HSTL-LVTTL If Mux mode is selected this is the clock input for Queue 0. All write port operations to Queue 0 will

(F1) INPUT be synchronous to this clock input.

If Demux or Broadcast mode is selected this is the clock input for the write port. All write port operations

will be synchronous to this clock input. Sampled on the rising edge of WCLK and independent of WDDR.

WCLK1-(G1) Write Clock 1/2/3 HSTL-LVTTL If Mux mode is selected these are the clock inputs for Queues 1, 2, and 3 respectively. All write

WCLK2-(H1) INPUT port operationson Queue1, Queue 2 and Queue 3 will be synchronous to clock inputs WCLK1,

WCLK3-(J1) WCLK2 and WCLK3 respectively.

If Demux or Broadcast mode is selected these clock inputs are ignored and can be tied to GND.

WCS0 Write Chip Select 0 HSTL-LVTTL If Mux mode is selected this is the write chip select input for Queue 0. All write operations on Queue 0

(U1) INPUT will occur synchronous to the WCLK0 input provided that WEN0 and WCS0 are LOW.

If Demux or Broadcast mode is selected this is the write chip select input for the write port. All write

operations will occur synchronous to the WCLK0 input provided that WEN0 and WCS0 are LOW.

Sampled on the rising edge of WCLK and independent of WDDR.

WCS1-(U2) Write Chip Select HSTL-LVTTL If Mux mode is selected these are the write chip select inputs for Queues 1, 2 and 3 respectively. All

WCS2-(U3) 1, 2, 3 INPUT write operations on Queue 1, Queue 2 and Queue 3 will occur synchronous to the WCLK1, 2 and 3

WCS3-(T1) respectively, provided that the corresponding write enable and write chip select inputs are LOW.

Sampled on the rising edge of WCLK and independent of WDDR.

If Demux or Broadcast mode is selected these inputs are ignored and can be tied HIGH.

WDDR Write Port DDR CMOS(1) During master reset, this pin selects the input port to operate in DDR or SDR format. If WDDR is HIGH,

(C7) INPUT then a word is written on the rising and falling edge of the appropriate WCLK0, 1, 2 and 3 input.

If WDDR is LOW, then a word is written only on the rising edge of the appropriate WCLK1, 1, 2 and

3 inputs.

WEN0 Write Enable 0 HSTL-LVTTL If Mux mode is selected this is the write enable input for Queue 0. All write operations on Queue 0 will

(T2) INPUT occur synchronous to the WCLK0 input provided that WEN0 and WCS0 are LOW.

If Demux or Broadcast mode is selected this is the write enable input for the write port. All write

operations will occur synchronous to the WCLK0 clock input provided that WEN0 and WCS0 are LOW.

WEN1-(T3) Write Enable 1/2/3 LVTTL If Mux mode is selected these are the write enable inputs for Queues 1, 2 and 3 respectively. All write

WEN2-(R1) operations on Queue 1, Queue 2 and Queue 3 will occur synchronous to the WCLK1, 2 and 3 inputs

WEN3-(R2) respectively, provided that the corresponding write enable and write chip select inputs are LOW.

If Demux or Broadcast mode is selected these inputs are ignored and can be tied HIGH.

PIN DESCRIPTIONS (CONTINUED)

Symbol & Name I/O TYPE Description

Pin No.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

PIN DESCRIPTIONS (CONTINUED)

Symbol & Name I/O TYPE Description

Pin No.

VCC +2.5V Supply Power These are VCC core power supply pins and must all be connected to a +2.5V supply rail.

(See Pin table)

VDDQ Output Rail Voltage Power This pin should be tied to the desired voltage rail for providing to the output drivers. Nominally 1.5V

(See Pin table) or 1.8V for HSTL, 2.5V for LVTTL.

GND Ground Pin Ground These ground pins are for the core device and must be connected to the GND rail.

(See Pin table)

Vref Reference voltage Analog This is a Voltage Reference input and must be connected to a voltage level determined in the Voltage

(A4) Recommended DC Operating Conditions section. This provides the reference voltage when using

HSTL class inputs. If HSTL class inputs are not being used, this pin must be connected to GND.

PIN NUMBER TABLE

Symbol Name I/O TYPE Pin Number

D[39:0] Data Input Bus HSTL-LVTTL D39-R3, D(38-36)-P(1-3), D(35-33)-N(1-3), D(32-30)-M(1-3), D(29-27)-L(1-3), D(26-24)-K(1-3),

INPUT D(23,22)-J(3,2), D(21,20)-H(3,2), D(19,18)-G(3,2), D(17,16)-F(3,2), D(15-13)-E(3-1),

D(12-10)-D(3-1), D(9-6)-C(4-1), D(5-3)-B(3-1), D(2-0)-A(3-1)

EF0/1/2/3- Empty Flags0-3 or HSTL-LVTTL EF0/OR0-V4, EF1/OR1-U5, EF2/OR2-U7, EF3/OR3-V10

OR0/1/2/3 Output Ready Flags 0-3 OUTPUT(2)

FF0/1/2/3- Full Flags0-3 or HSTL-LVTTL FF0/IR0-T4, FF1/IR1-V6, FF2/IR2-T10, FF3/IR3-U11

IR0/1/2/3 Input Ready Flags 0-3 OUTPUT(2)

Q[39:0] Data Output Bus HSTL-LVTTL Q(39,38)-U(17,16), Q(37-35)-T(17-15), Q(34,33)-R(17,16), Q(32-30)-P(18-16), Q(29-27)-N(18-16),

OUTPUT(2) Q(26-24)-M(18-16), Q(23-21)-L(18-16), Q20-K18, Q19-J18, Q(18-16)-H(16-18), Q(15-13)-G(16-18),

Q(12-10)-F(16-18), Q(9-7)-E(16-18), Q(6-4)-D(16-18), Q3-C18, Q2-B18, Q(1-0)-A(18-17)

VCC +2.5V Supply Power A9, B9, C9, D(6,9), E(4-9), F(4,5), G(4,5), H(4,5), J(4,5), K(4,5), L(4,5), M(4,5), N(4,5), P(4-8),

R(4-8), T8, U8, V8

VDDQ O/P Rail Voltage Power A11, B11, C11, D(11-15), E(11-15), F(14,15), G(14,15), H(14,15), J(14,15), K(14,15), L(14,15),

M(14,15), N(14,15), P(11-15), R(11-15)

GND Ground Pin Ground A10, B10, C10, D(7,8,10), E10, F(6-13), G(6-13), H(6-13), J(6-13), K(6-13), L(6-13), M(6-13),

N(6-13), P(9,10), R(9,10), T9, U9, V9

NOTES:

1. All CMOS pins should remain unchanged. CMOS format means that the pin is intended to be tied directly to VCC or GND and these particular pins are not tested for VIH

or VIL.

2. All unused outputs may be left floating.

3. These pins are for the JTAG port. Please refer to pages 36-40, Figure 7-9 for JTAG information.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

SET-UP, CONFIGURATION & RESET PINS

Regardless of the mode of operation, (Mux, Demux or Broadcast), the

following inputs must always be used. These inputs must be set-up with respect

to master reset as they are latched during master reset.

WDDR – Write Port DDR/SDR selection

RDDR – Read Port DDR/SDR selection

MD[1:0] – Mode Selection

OW[1:0] – Output width

IW[1:0] – Input Width

FSEL[1:0] – Flag offset default values

IOSEL – I/O Level Selection

PFM – Programmable Flag Mode

FWFT/SI – First word Fall Through or Standard IDT mode flag timing selection

MUX MODE

The following inputs/ outputs should be used when Mux mode is selected

by the user:

INPUTS:

WCLK0, WCLK1, WCLK2, WCLK3 – Four write port clocks

WEN0, WEN1, WEN2, WEN3 – Four write port enables

WCS0, WCS1, WCS2, WCS3 – Four write port chip selects

OS[1:0] - Output Select

RCLK0 – Read port clock

REN0 – Read port enable

RCS0 – Read port chip select

OE0 – Read port output enable

OUTPUTS:

ERCLK0 – Read port echo read clock

EREN0 – Read port echo read enable

EF0/OR0, EF1/OR1, EF2/OR2, EF3/OR3 – Four read port empty/output

ready flags

PAE0, PAE1, PAE2, PAE3 – Four read port programmable almost empty flags

PAF0, PAF1, PAF2, PAF3 – Four write port programmable almost full flags

FF0/IR0, FF1/IR1, FF2/IR2, FF3/IR3 – Four write port full/ input ready flags

CEF/COR – Composite empty/output ready flag on read port

SERIAL PORT

The following pins are used for writing and reading the Programmable Flag

Offsets values:

SCLK – Serial Clock

SWEN – Serial Write Enable

SREN – Serial Read Enable

FWFT/SI – Serial Data In

SDO – Serial Data Out

DEMUX OR BROADCAST MODE

The following inputs/outputs should be used when Demux or Broadcast

Write mode is selected by the user:

INPUTS:

IS[1:0] - Input Select, Demux mode only, not used in broadcast mode.

WCLK0 – Write port clock

WEN0 – Write port enable

WCS0 – Write port chip select

RCLK0, RCLK1, RCLK2, RCLK3 – Four read port clocks

REN0, REN1, REN2, REN3 – Four read port enables

RCS0, RCS1, RCS2, RCS3 – Four read port chip selects

OE0, OE1, OE2, OE3 – Four read port output enables

OUTPUTS:

ERCLK0, ERCLK1, ERCLK2, ERCLK3 – Four read port echo read clock

outputs

EREN0, EREN1, EREN2, EREN3 – Four read port echo read enable outputs

EF0/OR0, EF1/OR1, EF2/OR2, EF3/OR3 – Four read port empty/output

ready flags

FF0/IR0, FF1/IR1, FF2/IR2, FF3/IR3 – Four write port full/input ready flags

PAF0, PAF1, PAF2, PAF3 – Four write port programmable almost full flags

PAE0, PAE1, PAE2, PAE3 – Four read port programmable almost empty flags

CFF/CIR – Composite full/ input ready flag on write port

QUADMUX I/O USAGE SUMMARY

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

NOTES:

1 . Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause

permanent damage to the device. This is a stress rating only and functional operation

of the device at these or any other conditions above those indicated in the operational

sections of this specification is not implied. Exposure to absolute maximum rating

conditions for extended periods may affect reliability.

2. Compliant with JEDEC JESD8-5. VCC terminal only.

Symbol Parameter(1) Conditions Max. Unit

CIN(2,3) Input VIN = 0V 10(3) pF

Capacitance

COUT(1,2) Output VOUT = 0V 10 pF

Capacitance

CAPACITANCE (TA = +25°C, f = 1.0MHz)

NOTES:

1. With output deselected, (OE ≥ VIH).

2. Characterized values, not currently tested.

3. CIN for Vref is 20pF.

Symbol Parameter Min. Typ. Max. Unit

VCC Supply Voltage 2.375 2.5 2.625 V

VDDQ Output Supply Voltage  LVTTL 2.375 2.5 2.625 V

 eHSTL 1. 7 1. 8 1 . 9 V

 HSTL(2) 1.4 1.5 1.6 V

VREF Voltage Reference Input  eHSTL 0. 8 0 . 9 1 . 0 V

 HSTL(2) 0.68 0.75 0.9 V

GND Supply Voltage 0 0 0 V

VIH Input High Voltage  LVTTL 1.7 — 3.45 V

 eHSTL VREF+0.1 — VDDQ+0.3 V

 HSTL(2) VREF+0.1 — VDDQ+0.3 V

VIL Input Low Voltage  LVTTL — — 0.7 V

 eHSTL VREF-0.3 — VREF-0.1 V

 HSTL(2) VREF-0.3 — VREF-0.1 V

TAOperating Temperature Commercial 0 — +70 °C

TAOperating Temperature Industrial -40 — +85 °C

RECOMMENDED DC OPERATING CONDITIONS

NOTES:

1. VREF is only required for HSTL or eHSTL inputs. VREF should be tied LOW for LVTTL operation.

2. Compliant with JEDEC JESD8-6.

ABSOLUTE MAXIMUM RATINGS

Symbol Rating Com'l & Ind'l Unit

VTERM Terminal Voltage –0.5 to +3.6(2) V

with respect to GND

TSTG Storage Temperature –55 to +125 °C

IOUT DC Output Current –50 to +50 mA

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

DC ELECTRICAL CHARACTERISTICS

(Industrial: VCC = 2.5V ± 0.125V, TA = -40°C to +85°C)

Symbol Parameter Min. Max. Unit

ILI Input Leakage Current –10 +10 µA

ILO Output Leakage Current –10 +10 µA

VOH(7) Output Logic “1” Voltage, IOH = –8 mA @LVTTL VDDQ -0.4 — V

IOH = –8 mA @eHSTL VDDQ -0.4 — V

IOH = –8 mA @HSTL VDDQ -0.4 — V

VOL Output Logic “0” Voltage, IOL = 8 mA @LVTTL — 0. 4 V

IOL = 8 mA @eHSTL — 0.4 V

IOL = 8 mA @HSTL — 0.4 V

ICC1(1,2,3) Active VCC Current -- LVTTL — 240(6) mA

(See Note 8 and 9 for test conditions) -- eHSTL — 330(6) mA

-- HSTL — 330 (6) mA

IDDQ(1,2,3) Active VDDQ Current -- LVTTL — 50 mA

(See Note 8 and 9 for test conditions) -- eHSTL — 3 0 mA

-- HSTL — 30 mA

ISB1(1,2,3) Standby VCC Current (Mux mode) -- LVTTL — 110(6) mA

(See Note 10 and 11 for test conditions) -- eHSTL — 190(6) mA

-- HSTL — 190 (6) mA

ISB2(1,2,3) Standby VDDQ Current -- LVTTL — 40 mA

(See Note 10 and 11 for test conditions) -- eHSTL — 3 0 mA

-- HSTL — 30 mA

IPD1(1,2,3) Power Down VCC Current (Mux mode) - - LVTTL — 15(6) mA

(See Note 12 and 13 for test conditions) -- eHSTL — 30(6) mA

-- HSTL — 3 0 (6) mA

IPD2(1,2,3) Power Down VDDQ Current -- LVTTL — 0.5 mA

(See Note 12 and 13 for test conditions) -- eHSTL — 0.5 mA

-- HSTL — 0. 5 mA

NOTES:

1. Both WCLK and RCLK toggling at 20MHz.

2. Data inputs toggling at 10MHz.

3. Typical ICC1 calculation:for LVTTL I/O ICC1 (mA) = 10 x fS, fS = WCLK frequency = RCLK frequency (in MHz)

for HSTL or eHSTL I/O ICC1 (mA) = 72+ (10 x fS), fS = WCLK frequency = RCLK frequency (in MHz)

4. Typical IDDQ calculation: With Data Outputs in High-Impedance: IDDQ (mA) = 0.78 x fS

With Data Outputs in Low-Impedance: IDDQ (mA) = CL x VDDQ x fS x N /2000

fs = WCLK frequency = RCLK frequency (in MHz), VDDQ = 2.5V for LVTTL; 1.5V for HSTL; 1.8V for eHSTL

tA = 25°C, CL = capacitive load (pF), N = Number of bits switching

5. Total Power consumed: PT = [(VCC x ICC) + (VDDQ x IDDQ)]. IOH = -8mA for all voltage levels.

6. Maximum value tested wtih RCLK = WCLK = 20MHz at 85°C. Maximum value may differ depending on VCC and temperature.

7. Outputs are not 3.3V tolerant.

8. VCC = 2.5V, WCLK0-3 = RCLK0 = 20MHz, WEN0-3 = REN0 = LOW, WCS0-3 = RCS0 = LOW, OE = LOW, PD = HIGH.

9. VCC = 2.5V, WCLK0 = RCLK0-3 = 20MHz, WEN0 = REN0-3 = LOW, WCS0 = RCS0-3 = LOW, OE0-3 = LOW, PD = HIGH.

10. VCC = 2.5V, WCLK0-3 = RCLK0 = 20MHz, WEN0-3 = REN0 = HIGH, WCS0-3 = RCS0 = HIGH, OE = LOW, PD = HIGH.

11. VCC = 2.5V, WCLK0 = RCLK0-3 = 20MHz, WEN0 = REN0-3 = HIGH, WCS0 = RCS0-3 = HIGH, OE0-3 = LOW, PD = HIGH.

12. VCC = 2.5V, WCLK0-3 = RCLK0 = 20MHz, WEN0-3 = REN0 = HIGH, WCS0-3 = RCS0 = HIGH, OE = LOW, PD = LOW.

13. VCC = 2.5V, WCLK0 = RCLK0-3 = 20MHz, WEN0 = REN0-3 = HIGH, WCS0 = RCS0-3 = HIGH, OE0-3 = LOW, PD = LOW.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

AC ELECTRICAL CHARACTERISTICS(1)

(Commercial: VCC = 2.5V ± 0.15V, TA = 0°C to +70°C;Industrial: VCC = 2.5V ± 0.15V, TA = -40°C to +85°C; JEDEC JESD8-A compliant)

Commercial Commercial & Industrial

IDT72T55248L5 IDT72T55248L6-7

IDT72T55258L5 IDT72T55258L6-7

IDT72T55268L5 IDT72T55268L6-7

Symbol Parameter Min. Max. Min. Max. Unit

fS1 Clock Cycle Frequency (WCLK & RCLK) SDR — 200 — 150 MHz

fS2 Clock Cycle Frequency (WCLK & RCLK) DDR — 100 — 75 MHz

tAData Access Time 0.6 3.6 0.6 3.8 ns

tCLK1 Clock Cycle Time SDR 5 — 6.7 — ns

tCLK2 Clock Cycle Time DDR 10 — 13 — ns

tCLKH1 Clock High Time SDR 2.3 — 2.8 — ns

tCLKH2 Clock High Time DDR 4.5 — 6.0 — ns

tCLKL1 Clock Low Time SDR 2.3 — 2.8 — ns

tCLKL2 Clock Low Time DDR 4.5 — 6.0 — ns

tDS Data Setup Time 1.5 — 2.0 — ns

tDH Data Hold Time 0.5 — 0.5 — n s

tENS Enable Setup Time 1.5 — 2.0 — ns

tENH Enable Hold Time 0.5 — 0.5 — ns

fCClock Cycle Frequency (SCLK) — 10 — 10 MHz

tASO Serial Output Data Access Time — 20 — 20 ns

tSCLK Serial Clock Cycle 100 — 100 — ns

tSCKH Serial Clock High 45 — 45 — ns

tSCKL Serial Clock Low 45 — 45 — ns

tSDS Serial Data In Setup 15 — 1 5 — n s

tSDH Serial Data In Hold 5 — 5 — ns

tSENS Serial Enable Setup 5 — 5 — ns

tSENH Serial Enable Hold 5 — 5 — n s

tRS Reset Pulse Width 200 — 200 — ns

tRSS Reset Setup Time 15 — 15 — ns

tRSR Reset Recovery Time 10 — 10 — ns

tRSF Reset to Flag and Output Time — 12 — 15 ns

tOLZ (OE - Qn) Output Enable to Output in Low-Impedance 0.6 3.6 0.8 3.8 ns

tOHZ Output Enable to Output in High-Impedance 0 .6 3.6 0 .8 3.8 n s

tOE Output Enable to Data Output Valid 0 . 6 3 .6 0 . 8 3. 8 n s

tWFF Write Clock to FF or IR — 3.6 — 3.8 ns

tREF Read Clock to EF or OR — 3.6 — 3.8 ns

tCEF Read Clock to Composite EF or OR — 3.6 — 3.8 ns

tCFF Write Clock to Composite FF or IR — 3.6 — 3.8 ns

tPAFS Write Clock to Synchronous Programmable Almost-Full Flag — 3.6 — 3.8 ns

tPAES Read Clock to Synchronous Programmable Almost-Empty Flag — 3.6 — 3.8 ns

tPAFA Write Clock to Asynchronous Programmable Almost-Full Flag — 10 — 12 ns

tPAEA Read Clock to Asynchronous Programmable Almost-Empty Flag — 10 — 12 ns

tERCLK RCLK to Echo RCLK Output — 4.0 — 4.3 ns

tCLKEN RCLK to Echo REN Output — 3.6 — 3. 8 n s

tDTime Between Data Switching and ERCLK edge 0.4 — 0.5 — ns

tRCSLZ RCLK to Active from High-Impedance — 3.6 — 3.8 ns

tRCSHZ RCLK to High-Impedance — 3.6 — 3.8 ns

tSKEW1 SKEW time between RCLK and WCLK for EF/OR and FF/IR 4—5—ns

tSKEW2 SKEW time between RCLK and WCLK for EF/OR and FF/IR in DDR mode 5 — 7 — ns

tSKEW3 SKEW time between RCLK and WCLK for PAE and PAF 5—7—ns

NOTES:

1. With exception to clock cycle frequency, these parameters apply to both DDR and SDR modes of operation.

2. Values guaranteed by design, not currently tested.

3 . Industrial temperature range product for the 6-7ns speed grade is available as a standard device. All other speed grades available by special order.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

AC TEST LOADS

Figure 2a. AC Test Load

6157 drw06

50Ω

DDQ

I/O Z0 = 50Ω

10pF

Input Pulse Levels 0.25 to 1.25V

Input Rise/Fall Times 0.4ns

Input Timing Reference Levels 0.75V

Output Reference Levels 0.75V

HSTL

1.5V AC TEST CONDITIONS

Input Pulse Levels GND to 2.5V

Input Rise/Fall Times 1ns

Input Timing Reference Levels 1.25V

Output Reference Levels 1.25V

LVTTL

2.5V AC TEST CONDITIONS

NOTE:

1. VDDQ = 1.5V.

NOTE:

1. For LVTTL, VCC = VDDQ = 2.5V.

Input Pulse Levels 0.4 to 1.4V

Input Rise/Fall Times 0.4ns

Input Timing Reference Levels 0.9V

Output Reference Levels 0.9V

EXTENDED HSTL

1.8V AC TEST CONDITIONS

NOTE:

1. VDDQ = 1.8V.

Figure 2b. Lumped Capacitive Load, Typical Derating

6157 drw06a

20 30 50 80 100 200

Capacitance (pF)

∆t

(Typical, ns)

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

OUTPUT ENABLE & DISABLE TIMING

VIH

VIL

OE &

OLZ

100mV

OHZ

100mV

Single Output

Normally

LOW

Single Output

Normally

HIGH

VOL

VOH

DDQ

6157 drw07

Output

Enable

Output

Disable

DDQ

OLZ

Current data in output register

DDQ

Output Bus V

DDQ

OHZ

READ CHIP SELECT ENABLE & DISABLE TIMING

NOTES:

1. REN is HIGH.

2. OE is LOW.

RCS

tENS

tENH

tRCSLZ

RCLK

VDDQ

100mV

tRCSHZ

100mV

Output

Normally

LOW

Output

Normally

HIGH

VDDQ

6157 drw08

NOTES:

1. REN is HIGH.

2. RCS is LOW.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

FUNCTIONAL DESCRIPTION

MASTER RESET & DEVICE CONFIGURATION - MRS

During Master Reset the device operation is determined, this includes the

following:

1.Mux, Demux or Broadcast mode

2.IDT Standard or First Word Fall Through (FWFT) flag timing mode

3.Single or Double Data Rates on both the Write and Read ports

4. Programmable flag mode, synchronous or asynchronous timing

5.Write and read port bus widths, x10, x20 or x40

6.Default offsets for the programmable flags, 7, 63, 127 or 1023

7.LVTTL or HSTL I/O level selection

8. Input and output Queue selection

The state of the configuration inputs during a master reset will determine which

of the above modes are selected. A Master Reset comprises of pulsing the MRS

input ping from high to low for a period of time (tRS) with the configuration inputs

held in their respective states. Table 1 summarizes the configuration modes

available doing master reset. The are described as follows:

Mux/Demux/Broadcast. This mode is selected using the MD[1:0] inputs.

If during master reset, MD1 is HIGH and MD0 is LOW then Mux mode is selected.

If MD1 and MD2 are LOW then Demux is selected. If MD1 is LOW and MD0

is HIGH then Broadcast mode is selected.

IDT Standard or FWFT Mode. The two available flag timing modes are

selected using the FWFT/SI input. If FWFT/SI is LOW during Master Reset then

IDT Standard mode is selected, if it is high then FWFT mode is selected.

Single Data Rate (SDR) or Double Data Rate (DDR). The input/output

data rates are port selectable. This is a versatile feature that allows the user to

select either SDR or DDR on the write port(s) and/or read(s) port using the

WDDR and/or RDDR inputs. If WDDR is LOW during master reset then the write

port(s) will function in SDR mode, if it is high then the write port will be DDR mode.

If RDDR is LOW during master reset then the read port(s) will function in SDR

mode, if it is high then the read port will be DDR mode. Note that WDDR will select

the data rate mode for the single write port in Demux and Broadcast mode and

all four write ports in Mux mode. Likewise, RDDR will select the data rate mode

for the single read port in Mux mode and all four read ports in Demux and

Broadcast mode.

Programmable Almost Empty/Full Flags. These flags can operate in

either synchronous or asynchronous timing mode. If the programmable flag

input, PFM is HIGH during master reset then all programmable flags will operate

in a synchronous manner, meaning the PAE flags are double buffered and

updated based on the rising edge of its respective read clocks. The PAF flags

are also double buffered and updated based on the rising edge of its respective

write clocks. If it is LOW then all programmable flags will operate in an

asynchronous manner, meaning the PAE and PAF flags are not double buffered

and will update through the internal counter after a nominal delay.

Selectable Bus Width. The bus width can be selected on the write port in

Demux and Broadcast mode and on the read port in Mux mode. In Demux and

Broadcast mode the write port width is selected using the IW[1:0] inputs. If IW0

and IW1 are LOW then the write port will be 10 bits wide, if IW0 is LOW and IW1

is HIGH then the write port will be 20 bits wide, if IW0 is HIGH and IW1 is LOW

then the write port will be 40 bits wide. Note, in Demux and Broadcast mode all

read ports are 10 bits wide. In Mux mode the read port width is selected using

the OW[1:0] inputs. If OW0 and 0W1 are LOW then the read port will be 10 bits

wide, if OW0 is LOW and OW1 are HIGH then the read port will be 20 bits wide,

if OW0 is HIGH and OW1 are LOW then the read port will be 40 bits wide. Note,

in Mux mode all write ports are 10 bits wide.

Programmable Flag Offset Values. These offset values can be user

programmed or they can be set to one of four default values during a master

reset. For default programming, the state of the FSEL[1:0] inputs during master

TABLE 1 — DEVICE CONFIGURATION

PINS VALUES CONFIGURATION

MD[1:0] 00 Demux

10 Mux

01 Broadcast Write

11 Restricted

FWFT/SI 0 IDT Standard

1 FWFT

WDDR 0 Single Data Rate write port

1 Double Data Rate write port

RDDR 0 Single Data Rate read port

1 Double Data Rate read port

PFM 0 Asynchronous operation of PAE and PAF outputs

1 Synchronous operation of PAE and PAF outputs

IW[1:0] 0 0 Write port is 10 bits wide

0 1 Write port is 20 bits wide

1 0 Write port is 40 bits wide

11 Restricted

OW[1:0] 0 0 Read port is 10 bits wide

0 1 Read port is 20 bits wide

1 0 Read port is 40 bits wide

11 Restricted

FSEL[1:0] 00 Programmable flag offset registers value = 7

01 Programmable flag offset registers value = 63

10 Programmable flag offset registers value = 127

11 Programmable flag offset registers value = 1023

IOSEL 0 All applicable I/Os (except CMOS) are LVTTL

1 A ll applicable I/Os (except CMOS) are HSTL/eHSTL

IS[1:0] Mux/Broadcast Mode Demux Mode

00 not used Queue0

01 not used Queue1

10 not used Queue2

11 not used Queue3

OS[1:0] Mux Mode Demux/Broadcast Mode

00 Queue0 not used

01 Queue1 not used

10 Queue2 not used

11 Queue3 not used

IDT72T55248

IDT72T55258

IDT72T55268

FSEL1 FSEL0 Offsets n,m

00 7

0163

1 0 127

1 1 1,023

TABLE 2 — DEFAULT PROGRAMMABLE

FLAG OFFSETS

NOTES:

1. In default programming, the offset value selected applies to all internal Queues.

2. To program different offset values for each Queue, serial programming must be used.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

reset will determine the value. Table 1 lists the four offset values and how to select

them. For programming the offset values to a specific number, use the serial

programming signals (SCLK, SWEN, SREN, FWFT/SI) to load the value into

the offset register. You may also use the JTAG port on this device to load the

offset value. Keep in mind that you must disable the serial programming signals

if you plan to use the JTAG port for loading the offset values. To disable the serial

programming signals, tie SCLK, SWEN, SREN, and SI to VCC. A thorough

explanation of the serial and JTAG programming of the flag offset values is

provided in the next section.

I/O Level Selection. The I/Os can be selected for either 2.5V LVTTL levels

or 1.5V HSTL / 1.8V eHSTL levels. The state of the IOSEL input will determine

which I/O level will be selected. If IOSEL is HIGH then the applicable I/Os will

be 1.5V HSTL or 1.8V eHSTL, depending on the voltage level applied to VDDQ

and VREF. For HSTL, VDDQ and VREF = 0.75V and for eHSTL VDDQ and VREF

= 0.9V. If IOSEL is LOW then the applicable I/Os will be 2.5V LVTTLVREF =

0. As noted in the Pin Description section, IOSEL is a CMOS input and must be

tied to either VCC or GND for proper operation.

Input and Output Selection. During master reset, the value of IS[1:0] and

OS[1:0] will be held constant and indicates which internal Queue the read and

write port will select for initial operation. Data will be written to or read from this

internal Queue on the first valid write and read operation after master reset.

SERIAL WRITING AND READING OF OFFSET REGISTERS

These offset registers can be loaded with a default value or they can be user

programmed with another value. One of four default values are detected based

on the state of the FSEL[1:0] inputs, discussed in the Functional Description

SCLKTDI*

0008

TCK* SWEN

SREN

No Operation

IW/OW = x40

Serial read from registers:

104 bits for the IDT72T55248

112 bits for the IDT72T55258

120 bits for the IDT72T55268

1 bit for each rising SCLK edge

starting with empty offset (LSB)

ending with full offset (MSB)

IDT72T55258

IDT72T55268

IDT72T55278

Serial write into register:

104 bits for the IDT72T55248

112 bits for the IDT72T55258

120 bits for the IDT72T55268

1 bit for each rising SCLK edge

starting with empty offset (LSB)

ending with full offset (MSB)

6157 drwAA

IW/OW = x20

Serial write into register:

112 bits for the IDT72T55248

120 bits for the IDT72T55258

128 bits for the IDT72T55268

1 bit for each rising SCLK edge

starting with empty offset (LSB)

ending with full offset (MSB)

0007

Serial read from registers:

112 bits for the IDT72T55248

120 bits for the IDT72T55258

128 bits for the IDT72T55268

1 bit for each rising SCLK edge

starting with empty offset (LSB)

ending with full offset (MSB)

No Operation

Don’t

care

except

0008 &

0007

IW/OW = x10

Serial write into register:

120 bits for the IDT72T55248

128 bits for the IDT72T55258

136 bits for the IDT72T55268

1 bit for each rising SCLK edge

starting with empty offset (LSB)

ending with full offset (MSB)

Serial read from registers:

120 bits for the IDT72T55248

128 bits for the IDT72T55258

136 bits for the IDT72T55268

1 bit for each rising SCLK edge

starting with empty offset (LSB)

ending with full offset (MSB)

No Operation

NOTES:

* Programming done using the JTAG port.

1. The programming methods apply to both IDT Standard mode and FWFT mode.

2. Parallel programming is not featured in this device.

3. The number of bits includes programming to all four dedicated PAE/PAF offset registers.

Figure 3. Programmable Flag Offset Programming Methods

section earlier. User programming of the offset values can be performed by

either the dedicated serial programming port or the JTAG port. The dedicated

serial port can be used to load or read the contents of the offset registers. The

offset registers are programmed and read sequentially and behave similar to

a shift register.

The serial read and write operations are performed by the dedicated SCLK,

FWFT/SI, SWEN, SREN, and SDO pins. The total number of bits per device

is listed in Figure 4, Programmable Flag Offset Programming Methods. These

bits account for all four PAE/PAF offset registers in the device. To write to the

offset registers, set the serial write enable signal active (LOW), and on each rising

edge of SCLK one bit from the FWFT/SI pin is serially shifted into the flag offset

four registers, the programming sequence is complete. To read values from the

offsets registers, set the serial read enable active (LOW). Then on each rising

edge of SCLK, one bit is shifted out to the serial data output. The serial read

enable must be kept LOW throughout the entire read operation. To stop reading

the offset register, disable the serial read enable (HIGH). There is serial read

enable to SCLK time for reading the offset registers, as the offset register data

for each Queue is temporarily stored in a scan chain. When data has been

completely read out of the offset registers, any additional read operations to the

offset register will result in zeros as the output data.

Reading and writing of the offset registers can also be accomplished using

the JTAG port. To write to the offset registers using JTAG, set the instructional

load data into each of the offset registers in a similar fashion as the serial

programming described above. To read the values from the offset registers, set

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

the instructional register to the offset read command (Hex Value = 0x0007). The

TDO of the JTAG port will output data in a similar fashion as the serial

programming described above.

The number of bits required to load the offset registers is dependent on the

size of the device selected. Each offset register requires different total number

of bits depending on input and output bus width configuration. This total must be

programmed into the device in order for all the flags to be programmed correctly.

To change values of one or more offset register, all of the registers must be

reprogrammed serially again.

TIMING MODES: IDT STANDARD vs FIRST WORD FALL THROUGH

(FWFT) MODE

The IDT72T55248/72T55258/72T55268 support two different timing modes

of operation: IDT Standard mode or First Word Fall Through (FWFT) mode.

The selection of which mode will operate is determined during master reset, by

the state of the FWFT input.

During master reset, if the FWFT pin is LOW, then IDT Standard mode will

be selected. This mode uses the Empty Flag (EF) to indicate whether or not there

are any words present in the Queue. It also uses the Full Flag (FF) to indicate

whether or not the Queue has any free space for writing. In IDT Standard mode,

every word read from the Queue, including the first, must be requested using

the Read Enable (REN) and RCLK.

If the FWFT pin is HIGH during master reset, then FWFT mode will be

selected. This mode uses Output Ready (OR) to indicate whether or not there

is valid data at the data outputs. It also uses Input Ready (IR) to indicate whether

or not the Queue has any free space for writing. In the FWFT mode, the first word

written to an empty Queue goes directly to output bus after three RCLK rising

edges, applying RCS = LOW is not necessary. However, subsequent words

must be accessed using the (RCS) and RCLK. Various signals, in both inputs

and outputs operate differently depending on which timing mode is in effect. The

timing mode selected affects all internal Queues equally.

IDT STANDARD MODE

In this mode, the status flags FF, PAF, PAE, and EF operate in the manner

outlined in Table 3. To write data into the Queue, Write Enable (WEN) and WCS

must be LOW. Data presented to the DATA IN lines will be clocked into the Queue

on subsequent transitions of the Write Clock (WCLK). After the first write is

performed, the Empty Flag (EF) will go HIGH after three clock latency.

Subsequent writes will continue to fill up the Queue. The Programmable Almost-

Empty flag (PAE) will go HIGH after n + 1 words have been loaded into the

Queue, where n is the empty offset value. The default setting for these values

are listed in Table 3. This parameter is also user programmable as described

in the serial writing and reading of offset registers section.

Continuing to write data into the Queue without performing read operations

will cause the Programmable Almost-Full flag (PAF) to go LOW. Again, if no

reads are performed, the PAF will go LOW after (8,192-m) writes for the

IDT72T55248, (16,384-m) writes for the IDT72T55258, and (32,768-m) writes

for the IDT72T55268. This is assuming the I/O bus width is configured to x40.

If the I/O is x20, then PAF will go LOW after (16,384-m) writes for the

IDT72T55248, (32,768-m) writes for the IDT72T55258, and (65,536-m) writes

for the IDT72T55268. If the I/O is x10, then PAF will go LOW after (32,768-m)

writes for the IDT72T55248, (65,536-m) writes for the IDT72T55258, and

(131,072-m) writes for the IDT72T55268. The offset “m” is the full offset value.

The default setting for these values are listed in Table 3. This parameter is also

user programmable. See the section on serial writing and reading of offset

registers for details.

When the Queue is full, the Full Flag (FF) will go LOW, inhibiting further write

operations. If no reads are performed after a reset, FF will go LOW after D writes

to the Queue. If the I/O bus width is configured to x40, then D = 8,192 writes for

the IDT72T55248, 16,384 writes for the IDT72T55258, and 32,768 writes for

the IDT72T55268. If the I/O is x20, then D = 16,384 writes for the IDT72T55248,

32,768 writes for the IDT72T55258, and 65,536 writes for the IDT72T55268.

If the I/O is x10, then D = 32,768 writes for the IDT72T55248, 65,536 writes

for the IDT72T55258, and 131,072 writes for the IDT72T55268.

6157 drwAB

Offset

PAE3

PAF3

PAE2

PAF2

PAE1

PAF1

PAE0

PAF0

14 - 26

27 - 39

40 - 52

53 - 65

66 - 78

1 - 13

79 - 91

92 - 104

Serial Bits

IDT72T55248

IW/OW = x20

IDT72T55258

IW/OW = x40

IDT72T55248

IW/OW = x20

or IDT72T55258

IW/OW = x20

or IDT72T55268

IW/OW = x40

IDT72T55248

IW/OW = x40

IDT72T55268

IW/OW = x10

IDT72T55258

IW/OW = x10

IDT72T55268

IW/OW = x20

15 - 28

29 - 42

43 - 56

57 - 70

71 - 84

1 - 14

85 - 98

99 - 112

16 - 30

31 - 45

46 - 60

61 - 75

76 - 90

1 - 15

91 - 105

106 - 120

17 - 32

33 - 48

49 - 64

65 - 80

81 - 96

1 - 16

97 - 112

113 - 128

18 - 34

35 - 51

52 - 68

69 - 85

86 - 102

1 - 17

103 - 119

120 - 136

Figure 4. Offset Registers Serial Bit Sequence

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

If the Queue is full, the first read operation will cause FF to go HIGH after two

WCLKS. Subsequent read operations will cause PAF to go HIGH at the

conditions described in Table 3. If further read operations occur, without write

operations, PAE will go LOW when there are n words in the Queue, where n

is the empty offset value. Continuing read operations will cause the Queue to

become empty. Then the last word has been read from the Queue, the EF will

go LOW inhibiting further read operations. REN is ignored when the Queue is

empty.

When configured in IDT Standard mode, the EF and FF outputs are double

configured in both Single Data Rate and Double Data Rate mode. Relevant

timing diagrams for IDT Standard mode can be found in Figures 14, 15, 16.

FIRST WORD FALL THROUGH MODE (FWFT)

In this mode, the status flags OR, IR, PAE, and PAF operate in the manner

outlined in Table 4. To write data into to the Queue, WCS must be LOW. Data

presented to the DATA IN lines will be clocked into the Queue on subsequent

transitions of WCLK. After the first write is performed, the Output Ready (OR)

flag will go LOWafter 3rd rising edge of RCLK. Subsequent writes will continue

to fill up the Queue. PAE will go HIGH after n + 2 words have been loaded into

the Queue, where n is the empty offset value. The default setting for these values

are listed in Table 4. This parameter is also user programmable as described

in the serial writing and reading of offset registers section.

Continuing to write data into the Queue without performing read operations

will cause the Programmable Almost-Full flag (PAF) to go LOW. Again, if no

reads are performed, the PAF will go LOW after (8,193-m) writes for the

IDT72T55248, (16,385-m) writes for the IDT72T55258, and (32,769-m) writes

for the IDT72T55268. This is assuming the I/O bus width is configured to x40.

If the I/O is x20, then PAF will go LOW after (16,385-m) writes for the

IDT72T55248, (32,769-m) writes for the IDT72T55258, and (65,537-m) writes

for the IDT72T55268. If the I/O is x10, then PAF will go LOW after (32,769-m)

writes for the IDT72T55248, (65,537-m) writes for the IDT72T55258, and

(131,073-m) writes for the IDT72T55268. The offset “m” is the full offset value.

The default setting for these values are listed in Table 4. This parameter is also

user programmable. See the section on serial writing and reading of offset

registers for details.

When the Queue is full, the Input Ready (IR) will go LOW, inhibiting further

write operations. If no reads are performed after a reset, IR will go LOW after

D writes to the Queue. If the I/O bus width is configured to x40, then D = 8,193

writes for the IDT72T55248, 16,385 writes for the IDT72T55258, and 32,769

writes for the IDT72T55268. If the I/O is x20, then D = 16,385 writes for the

IDT72T55248, 32,769 writes for the IDT72T55258, and 65,537 writes for the

IDT72T55268. If the I/O is x10, then D = 32,769 writes for the IDT72T55248,

65,537 writes for the IDT72T55258, and 131,073 writes for the IDT72T55268.

If the Queue is full, the first read operation will cause IR to go HIGH after two

WCLKs after RCLK. Subsequent read operations will cause PAF to go HIGH

at the conditions described in Table 4. If further read operations occur, without

write operations, PAE will go LOW when there are n words in the Queue, where

n is the empty offset value. Continuing read operations will cause the Queue to

become empty. Then the last word has been read from the Queue, the OR will

go HIGH inhibiting further read operations. RCS is ignored when the Queue

is empty.

When configured in FWFT mode, the OR flag output is triple register-buffered

and the IR flag output is double register-buffered. Relevant timing diagrams for

FWFT mode can be found in Figures 17, 18, 19.

6157 drwSFT

1 to n

(1)

(n+1) to (8,192 - m)

8,192

FF PAF PAE EF

HHLL

HHLH

HLHH

LLHH

IDT72T55248 IDT72T55258

IDT72T55258

IDT72T55248

OW = x20

Number of

Words in

Queue

OW = x10

IDT72T55268

OW = x40

IDT72T55268

IDT72T55258 IDT72T55268

1 to n

(1)

(n+1) to (16,384 - m)

16,384

1 to n

(1)

(n+1) to (32,768 - m)

32,768

1 to n

(1)

(n+1) to (65,536 - m)

65,536

1 to n

(1)

(n+1) to (131,072 - m)

131,072

1 to n+1

(1)

(n+2) to (8,193 - m)

8,193

FF PAF PAE EF

HHLL

HHLH

HLHH

LLHH

IDT72T55248 IDT72T55258

IDT72T55258

IDT72T55248

OW = x20

Number of

Words in

Queue

OW = x10

IDT72T55268OW = x40

IDT72T55268

IDT72T55258 IDT72T55268

1 to n+1

(1)

(n+2) to (16,385 - m)

16,385

1 to n+1

(1)

(n+2) to (32,769 - m)

32,769

1 to n+1

(1)

(n+2) to (65,537 - m)

65,537

1 to n+1

(1)

(n+2) to (131,073 - m)

131,073

NOTE:

1. n, m = 7 if FSEL[1:0] = 00, n, m = 63 if FSEL[1:0] = 01, n, m = 127 if FSEL[1:0] = 10, n, m = 1023 if FSEL[1:0] = 11.

NOTE:

1. n, m = 7 if FSEL[1:0] = 00, n, m = 63 if FSEL[1:0] = 01, n, m = 127 if FSEL[1:0] = 10, n, m = 1023 if FSEL[1:0] = 11.

TABLE 3 — STATUS FLAGS FOR IDT STANDARD MODE

TABLE 4 — STATUS FLAGS FOR FWFT MODE

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

HSTL/LVTTL I/O

The inputs and outputs of this device can be configured for either LVTTL or

HSTL/eHSTL operation. If the IOSEL pin is HIGH during master reset, then all

applicable LVTTL or HSTL signals will be configured for HSTL/eHSTL

operating voltage levels. To select between HSTL or eHSTL VREF must be

driven to 0.75V or 0.9V respectively. Typically a logic HIGH in HSTL would

be VREF ±300mV and a logic LOW would be VREF ±300mV. If the IOSEL pin

is LOW during master reset, then all applicable LVTTL or HSTL signals will be

configured for LVTTL operating voltage levels. In this configuration VREF must

be set to the static core voltage of 2.5V. Table 5 illustrates which pins are and

are not associated with this feature. Note that all “Static Pins” must be tied to VCC

or GND. These pins are CMOS only and are purely device configuration pins.

Note the IOSEL pin should be tied HIGH or LOW and cannot toggle before and

after master reset.

BUS MATCHING

The write and read port has bus-matching capability such that the input and

output bus can be either 10 bits, 20 bits or 40 bits wide, depending on which

operating mode the device is configured to. The bus width of both the input and

output port is determined during master reset using the input and output width

setup pins (IW[1:0], OW[1:0]). The selected port width is applied to all four Queue

ports, such that all four Queues will be configured for either x10, x20 or x40 bus

widths. When writing or reading data from a Queue the number of memory

locations available to be written or read will depend on the bus width selected

and the density of the device.

If the write/read port is 10 bits wide, this provides the user with a Queue depth

of 32,768 x 10 for the IDT72T55248, 65,536 x 10 for the IDT72T55258, or

131,072 x 10 for the IDT72T55268. If the write/read port is 20 bits wide, this

provides the user with a Queue depth of 16,384 x 20 for the IDT72T55248,

32,768 x 20 for the IDT72T55258, or 65,536 x 20 for the IDT72T55268. If the

write/read port is 40 bits wide, this provides the user with a Queue depth of 8,192

x 40 for the IDT72T55248, 16,384 x 40 for the IDT72T55258, or 32,768 x 40

for the IDT72T55268. The Queue depths will always have a fixed density of

327,680 bits for the IDT72T55248, 655,360 bits for the IDT72T55258 and

1,310,072 bits for the IDT72T55268 regardless of bus-width configuration on

the write/read port.

When the device is operating in double data rate, the word is twice as large

as in single data rate since one word written or read on both the rising and falling

edge of clock. Therefore in DDR, the Queue depths will be half of what it is

mentioned above. For instance, if the write/read port is 10 bits wide, the depth

of each Queue is 16,384 x 10 for the IDT72T55248, 32,768 x 10 for the

IDT72T55258, or 65,536 x 10 for the IDT72T55268.

See Figure 5, Bus-Matching Byte Arrangement for more information.

LVTTL/HSTL/eHSTL STATIC CMOS SIGNALS

Write Port Read Port JTAG Control Pins Serial Port Static Pins

D[39:0] CEF/COR TCK FSEL[1:0] SCLK IOSEL

WCLK0/1/2/3 EF0/1/2/3 TRST IS[1:0] SREN IW[1:0]

WEN0/1/2/3 OR0/1/2/3 TMS OS[1:0] SWEN MD[1:0]

FF0/1/2/3 ERCLK0/1/2/3 TDI PD FWFT/SI OW[1:0]

WCS0/1/2/3 OE0/1/2/3 TDO MRS SDO PFM

CFF/CIR PAE0/1/2/3 PRS0/1/2/3 RDDR

PAF0/1/2/3 Q[39:0] FWFT/SI WDDR

RCLK0/1/2/3

RCS0/1/2/3

REN0/1/2/3

EREN[3:0]

TABLE 5 — I/O VOLTAGE LEVEL ASSOCIATIONS

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 5. Bus-Matching Byte Arrangement (Mux Mode)

6157 drw09

x10 INPUT to x40 OUTPUT for Queue0

2nd: Write to Queues

OS1 OS0 OW1

BYTE ORDER ON OUTPUT PORT:

D39-D30 D29-D20 D19-D10 D9-D0

1st: Write to Queues

MUX MODE

BYTE ORDER ON INPUT PORT:

4th: Write to Queues

3rd: Write to Queues

Queue0

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

1st: Read from Queues

BCD

1st: Read from Queues

2nd: Read from Queues

x10 INPUT to x20 OUTPUT for Queue0

2nd: Read from Queues

1st: Read from Queues

4th: Read from Queues

3rd: Read from Queues

x10 INPUT to x10 OUTPUT for Queue0

OW0

OS1 OS0 OW1

BYTE ORDER ON OUTPUT PORT:

OW0

OS1 OS0 OW1

OW0

BYTE ORDER ON OUTPUT PORT:

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

Queue1Queue2Queue3

NOTES:

= High-Z outputs.

= Inputs set to GND.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 5. Bus-Matching Byte Arrangement (Demux Mode) (Continued)

6157 drw10

x40 INPUT to x10 OUTPUT for Queue1

1st: Read from Queues

D39-D30 D29-D20 D19-D10 D9-D0

1st: Write to Queues

3rd: Read from Queues

2nd: Read from Queues

1st: Write to Queues

x20 INPUT to x10 OUTPUT for Queue1

x10 INPUT to x10 OUTPUT for Queue1

LHLH

IS1 IS0 IW1

IW0

4th: Read from Queues

IS1 IS0 IW1 IW0

1st: Read from Queues

2nd: Read from Queues

1st: Write to Queues

1st: Read from Queues

LHLL

IS1 IS0 IW1 IW0

DEMUX MODE

BYTE ORDER ON INPUT PORT:

BCD

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

Note:

X is data in the output register.

D39-D30 D29-D20 D19-D10 D9-D0

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

Q39-Q30 Q29-Q20 Q19-Q10 Qn-Q0

D39-D30 D29-D20 D19-D10 D9-D0

Queue0Queue1Queue2Queue3

X X X

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 5. Bus-Matching Byte Arrangement (Broadcast Mode) (Continued)

6157 drw11

x40 INPUT to x10 OUTPUT for Every Queue

1st: Read from Queues

A1st: Write to Queues

BROADCAST MODE

BYTE ORDER ON INPUT PORT:

3rd: Read from Queues

2nd: Read from Queues

1st: Write to Queues

x20 INPUT to x10 OUTPUT for Every Queue

x10 INPUT to x10 OUTPUT to Every Queue

4th: Read from Queues

1st: Read from Queues

2nd: Read from Queues

1st: Write to Queues

1st: Read from Queues

L L

IW1 IW0

AAAA

BBBB

CCCC

DDDD

AAAA

BBBB

AAAA

L H

IW1 IW0

H L

IW1 IW0

BYTE ORDER ON INPUT PORT:

D39-D30 D29-D20 D19-D10 D9-D0

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

D39-D30 D29-D20 D19-D10 D9-D0

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

D39-D30 D29-D20 D19-D10 D9-D0

Q39-Q30 Q29-Q20 Q19-Q10 Q9-Q0

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

SELECTABLE MODES

The device is capable of operating in three different modes, Mux, Demux,

and Broadcast Write. Each of these three modes can be selected based on the

MD[1:0] bits. These bits should be tied directly to VCC or GND as they are latched

in during master reset. The state of the MD pins for each mode is summarized

in Table 1 – Device Configuration.

Each mode has access to four dedicated Queues internally, with each Queue

having densities of 327,680 bits for the IDT72T55248, 655,360 bits for the

IDT72T55258 and 1,310,072 bits for the IDT72T55268. The density of each

Queue is fixed and cannot be programmed. Also, the density does not change

when the device is operating in single or double data rate, or when the device

is utilizing the bus-matching feature.

The QuadMux flow-control device accommodates for all of the timing issues

associated with converging multiple data rates onto one path. Such issues

include clock skew, race conditions, and meeting setup and hold times. These

issues are difficult to address when performing mux operations from external

logic or within an FPGA, especially at higher frequencies. The complexity of the

design makes it difficult to implement within an FPGA, where speed degradations

occur as the circuit becomes more complicated.

MUX MODE

In Mux mode the device is configured as shown in the Mux mode block

diagram on page 1. The device in this mode consists of four separate Queues:

Queue 0, Queue 1, Queue 2 and Queue 3. The four Queues all have the same

common read port, and the read control selecting which Queue to read from.

The Mux mode can be used in applications where multiple incoming data rates

from different data paths are being buffered to one common data rate and data bus.

WRITE PORT OPERATION

In Mux mode there are four independent write port controls for each individual

Queue. Data can be written to any of the four Queues using its corresponding

write clock, write enable, and write chip select. A data word will be written on

the rising (and falling in DDR) edge of write clock provided WEN and write chip

select are active. Note in double data rate the setup and hold times of the write

enables and write chip selects are sampled with respect to the rising edge of its

respective write clock only. The falling edge of WCLK does not sample the write

enable and write chip select.

In FWFT mode the first word written to any Queue will automatically be placed

onto the output bus of that respective Queue when selected on the read port via

the OS[1:0] pins. There is a two cycle input pipeline and a two cycle output

pipeline. It will take two cycles or three rising edges of the WCLK to move data

from the write port to the queue and two cycles or those rising edges of RCLK

to move data from the queue to the data outlines. This is regardless of the state

of the corresponding read enable and read chip select, provided that the

selected Queue was empty. This is not true in IDT Standard mode, where the

first word written to a selected Queue must be accessed by setting REN and RCS

are LOW on the rising edge of RCLK.

READ PORT OPERATION

In Mux mode the output select pins (OS[1:0]) determine which one of the four

Queues the output bus will read data from. The output select pins are sampled

on the rising edge of every RCLK, and may change on every clock edge. Thus

there is no latency switching from one Queue to another. Note that in Mux mode

only the RCLK0 is active, all other output read clocks are not used. The same

applies to the read enable (REN0) and read chip select (RCS0). Data will be

read on the rising (and falling in DDR) edge of read clock provided read enable

and read chip select are active (LOW). When selecting a Queue for read

operations the new word read from that Queue will be available immediately on

the next clock edge after the new Queue is selected. For example, if OS[1:0]

is set to 01 (Queue1) on RCLK edge 0, then on RCLK edge 1 (next read clock

edge) data can be read from Queue1 if REN0 and RCS0 are enabled.

In FWFT mode, the first word written to a selected Queue will automatically

be placed onto the output bus of that respective Queue regardless of the state

of the corresponding read enable, provided that the selected Queue was empty

and its corresponding output ready flag was inactive. This occurs due to the

nature of the FWFT flag timing. There is a two cycle input pipeline and a two cycle

output pipeline. It will take two cycles or three rising edges of the WCLK to move

data from the write port to the queue and two cycles or those rising edges of RCLK

to move data from the queue to the data outlines. Subsequent writes to the Queue

that is not empty will not fall through to the output bus. Note in FWFT mode, during

a Queue selection the next word available in the Queue will automatically fall

through to the output bus regardless of the read enable and read chip select.

In IDT Standard mode, every word including the first word must be accessed

by the read enable and read chip select. Unlike FWFT mode, during a Queue

selection the next word available in the Queue will not automatically fall through

to the output bus. The previous word that was read out of the read port will remain

on the output bus if the REN and RCS select are HIGH.

DEMUX MODE

In Demux mode the device is configured as shown in the Demux mode block

diagram on page 2. The device in this mode consists of four separate Queues:

Queue 0, Queue 1, Queue 2 and Queue 3. The four Queues all have the same

common write port, and the read control selecting which Queue to read from.

The Demux mode can be used in applications where a single incoming data

rate is being buffered to multiple outgoing data rates.

WRITE PORT OPERATION

In Demux mode the input select pins (IS[1:0]) determine which one of the four

Queues the input bus will write data into. The input select pins are sampled on

the rising edge of every WCLK, and may change on every clock edge. Thus

there is no latency switching from one Queue to another. Note that in Demux

mode only the WCLK0 is active, all other input write clocks are not used. The

same applies to the write enable (WEN0) and write chip select (WCS0). Data

will be written on the rising (and falling in DDR) edge of write clock provided WEN

and WCS are active on the rising edge of the WCLK. Note in double data rate

the setup and hold times of the WEN and WCS selects are sampled with respect

to the rising edge of the write clock only. The falling edge of WCLK does not

sample the write enable and write chip select. When selecting a Queue for write

operations the next word can be written to that Queue immediately on the next

clock edge after the new Queue is selected. For example, if IS[1:0] is set to 01

(Queue1) on WCLK edge 0, then on WCLK edge 1 (next read clock edge) data

can be written to Queue1 if WEN0 and WCS0 are enabled.

In FWFT mode the first word written to a selected Queue will automatically

be placed onto the output bus regardless of the state of the corresponding read

enable, provided that the selected Queue was empty and its corresponding

output ready flag was inactive. There is a two cycle input pipeline and a two cycle

output pipeline. It will take two cycles or three rising edges of the WCLK to move

data from the write port to the queue and two cycles or those rising edges of RCLK

to move data from the queue to the data outlines. This occurs due to the nature

of the FWFT flag timing. Subsequent writes to the Queue that is not empty will

not fall through to the output bus. In IDT Standard mode, every word including

the first word must be accessed by the read enable and read chip select.

READ PORT OPERATION

In Demux mode there are four independent read port controls for each

individual Queue. Data can be read from any of the four Queues using its

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

corresponding read clock, read enable, and read chip select. A data word will

be read on the rising (and falling in DDR) edge of read clock provided read

enable and read chip select are active. There are also four individual output

enables that will take the output bus to high-impedance. Note that data will be

read from memory regardless of the state of the output enable OE[3:0] pins.

As explained above, in FWFT mode the first word written to each Queue will

automatically be placed onto the output bus regardless of the of the state of the

corresponding read enable. There is a two cycle input pipeline and a two cycle

output pipeline. It will take two cycles or three rising edges of the WCLK to move

data from the write port to the queue and two cycles or those rising edges of

RCLK to move data from the queue to the data outlines.

BROADCAST WRITE MODE

In Broadcast Write mode the device is configured as shown in the Broadcast

Write mode block diagram on page 2. The device in this mode consists of four

separate Queues: Queue 0, Queue 1, Queue 2 and Queue 3. The four Queues

all have one common write port which will write data into all four Queues

simultaneously when a write operation is initiated, there is no write selection

to write data into a specific Queue. The Broadcast Write mode can be used in

applications where a single incoming data bus needs to be sent to multiple data

paths simultaneously.

WRITE PORT OPERATION

In Broadcast Write mode there are no input or output select pins to select the

individual Queues separately. The write port will write data into all four Queues

simultaneously. Note that in Broadcast mode only the WCLK0 is active, all other

input clocks are not used. The same applies to the write enable (WEN0) and

write chip select (WCS0). Data will be written on the rising (and falling in DDR)

edge of write clock provided write enable and write chip select are active (LOW)

on the rising edge of write clock. Write operations are prohibited if any of the

four Queues are being partially reset or any of their full flag status full (FF =

LOW).

In FWFT mode, the first word written to a selected Queue will automatically

be placed onto the output bus of that respective Queue regardless of the state

of the corresponding read enable, provided that the selected Queue was empty

and its corresponding output ready flag was inactive. There is a two cycle input

pipeline and a two cycle output pipeline. It will take two cycles or three rising

edges of the WCLK to move data from the write port to the queue and two cycles

or those rising edges of RCLK to move data from the queue to the data outlines.

This occurs due to the nature of the FWFT flag timing. Subsequent writes to

the Queue that is not empty will not fall through to the output bus. In IDT Standard

mode, every word including the first word must be accessed by the read enable

and read chip select.

READ PORT OPERATION

In Broadcast Write mode there are four independent read port controls for

each individual Queue. Data can be read from any of the four Queues using

its corresponding read clock, read enable, and read chip select. A data word

will be read on the rising (and falling in DDR) edge of read clock provided read

enable and read chip select are active. There are also four individual output

enables that will take the output bus to high-impedance. Note that data will be

read from memory regardless of the state of the output enable OE[3:0] pins.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

SIGNAL DESCRIPTIONS

INPUTS:

DATA INPUT BUS (D[39:0])

The data input bus can be 40, 20, or 10 bits wide in Demux and Broadcast

mode. D[39:0] are data inputs for the 40-bit wide data bus, D[19:0] are data

inputs for 20-bit wide data bus, and D[9:0] are data inputs for the 10-bit wide

data bus. In Mux mode the input bus will be 10 bits wide for each of the four

internal Queues. D[9:0] are dedicated to Queue 0, D[19:10] are dedicated to

Queue 1, D[29:20] are dedicated to Queue 2, and D[39:30] are dedicated to

Queue 3. Data can be written into each of the four Queues on every WCLK

cycle. There is a two cycle input pipeline and a two cycle output pipeline. It will

take two cycles or three rising edges of the WCLK to move data from the write

port to the queue and two cycles or those rising edges of RCLK to move data

from the queue to the data outlines.

MASTER RESET (MRS)

There is a single master reset available for all internal Queues in this device.

A master reset is accomplished whenever the MRS input is taken to a LOW state.

This operation sets the internal read and write pointers of all Queues to the first

location in memory. The programmable almost empty flag will go LOW and the

almost full flags will go HIGH.

If FWFT/SI signal is LOW during master reset then IDT Standard mode is

selected. This mode utilizes the empty and full status flags from the EF/OR and

FF/IR dual-purpose pin. During master reset, all empty flags will be set to LOW

and all full flags will be set to HIGH.

If FWFT/SI signal is HIGH during master reset, then the First Word Fall

Through mode is selected. This mode utilizes the input read and output ready

status flags from the EF/OR and FF/IR dual-purpose pin. During master reset,

all input ready flags will be set to LOW and all output ready flags will be set to

HIGH.

All device configuration pins such as MD[1:0], OW[1:0], IW[1:0], IS[1:0],

OS[1:0], WDDR, RDDR, IOSEL, PFM, FSEL[1:0] and FWFT/SI needs to be

defined before the master reset cycle. During a master reset the output register

is initialized to all zeros. If the output enable(s) are LOW during master reset,

then the output bus will be LOW. If the output enable(s) are HIGH during master

reset, then the output bus will be in High-impedance. RCS has no affect on the

data outputs during master reset. If the output width OW[1:0] is configured to

x10 or x20, then the unused outputs will be in high-impedance. A master reset

is required after power up before a write operation to any Queue can take place.

Master reset is an asynchronous signal and thus the read and write clocks can

be free-running or idle during master reset. See Figure 10, Master Reset

Timing, for the associated timing diagram.

PARTIAL RESET (PRS0/1/2/3)

A partial reset is a means by which the user can reset both the read and write

pointers of each individual Queue inside the device without changing the

Queue’s configuration. There are four dedicated partial reset signals that each

correspond to an individual Queue. There are restrictions as to when partial

reset can be performed that apply to each operating modes.

In Mux mode, partial reset may not be performed on the two Queues involved

during Queue selection on the read port. For instance, if OS[1:0] is switching

from 00 to 01 then PRS0 and PRS1 may not be enabled from the first rising RCLK

edge with OS[1:0]=01 until three more rising RCLK edges have been received.

In other words, partial reset may not be performed for a minimum of three RCLK

cycles from the time a new Queue is selected. Also, if Queue0 or Queue1 are

partially reset before the switch, the appropriate PRS signal must return HIGH

at least tRSR (reset recovery time) before the first RCLK edge with OS[1:0]=01.

Any Queues not involved in the selection can be partially reset.

In Demux mode, partial reset may not be performed on the two Queues

involved during Queue selection on the write port. For instance, if IS[1:0] is

switching from 11 to 10 then PRS3 and PRS2 may not be enabled from the first

rising WCLK edge with OS[1:0]=01 until three more rising WCLK edges have

been received. In other words, partial reset may not be performed for a minimum

of three WCLK cycles from the time a new Queue is selected. Also, if Queue0

or Queue1 are partially reset before the switch, the appropriate PRS signal must

be HIGH at least tRSR (reset recovery time) before the first WCLK edge with

IS[1:0]=10. Any Queues not involved in the selection can be partially reset.

In Broadcast mode, partial reset may not be performed during write

operations. The write enable and write chip select must be HIGH with respect

to the rising edge of WCLK0 for a minimum of tRSS before partial reset can be

performed. If the device is operating in DDR mode, partial reset of any Queue

must be initiated after the falling edge of WCLK0 to ensure data from the falling

edge are written into all four Queues in memory. This maintains the data integrity

of all four Queues in the device.

See Figures 11, 12, 13, Partial Reset Timing, for the associated timing

diagram.

FIRST WORD FALL THROUGH/SERIAL IN (FWFT/SI)

This is a dual purpose pin. During Master Reset, the state of the FWFT/SI

input determines whether the device will operate in IDT Standard mode or First

Word Fall Through (FWFT) mode.

If FWFT/SI is LOW before the falling edge of master reset, then IDT Standard

mode will be selected. This mode uses the Empty Flag (EF) to indicate whether

or not there are any words present in the Queues memory. It also uses the

Full Flag function (FF) to indicate whether or not the Queues memory has any

free space for writing. In IDT Standard mode, every word read from the

Queues, including the first, must be requested using the Read Enable (REN),

Read Chip Select (RCS) and RCLK.

If FWFT/SI is HIGH before the falling edge of master reset, then FWFT mode

will be selected. This mode uses Output Ready (OR) to indicate whether or not

there is valid data at the data outputs (Qn). It also uses Input Ready (IR) to

indicate whether or not the Queues have any free space for writing. In the

FWFT mode, the first word written to an empty Queue goes directly to Qn after

three RCLK rising edges, provided that the first RCLK meets tSKEW param-

eters. There will be a one RCLK cycle delay if tSKEW is not met. REN and RCS

do not need to be enabled. Subsequent words must be accessed using the

REN, RCS, and RCLK. RCS must be LOW or the outputs will be in a High-

state.

The state of the FWFT/SI input must be kept at the present state for the

minimum of the reset recovery time (tRSR) after master reset. After this time, the

FWFT/SI acts as a serial input for loading PAE and PAF offsets into the

programmable offset registers. The serial input is used in conjunction with

SCLK, SWEN, SREN, and SDO to access the offset registers. Serial program-

ming using the FWFT/SI pin functions the same way in both IDT Standard and

FWFT modes.

WRITE CLOCK (WCLK0/1/2/3)

There are a possible total of four write clocks available in this device

depending on the mode selected, each corresponding to the individual Queues

in memory. A write cycle is initiated on the rising and/or falling edge of the WCLK

input. If the write double data rate (WDDR) mode pin is tied HIGH during master

reset, data will be written on both the rising and falling edge of WCLK0/1/2/3,

provided that WEN0/1/2/3 and WCS0/1/2/3 are enabled. If WDDR is tied LOW,

data will be written only on the rising edge of WCLK0/1/2/3 provided that WEN0/

1/2/3 and WCS0/1/2/3 are enabled. The four write clocks are completely

independent of one another.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Data setup and hold times must be met with respect to the LOW-to-HIGH (and

HIGH-to-LOW in DDR) transition of the write clock(s). It is permissible to stop

the write clock(s). Note that while the write clocks are idle, the FF/IR0/1/2/3 and

PAF0/1/2/3 flags will not be updated unless it is operating in asynchronous

timing mode (PFM=00). The write clocks can either be independent or

coincident of one another.

In Demux and Broadcast Write mode, only the WCLK0 input is available.

All other write clocks inputs should be tied to GND.

WRITE ENABLE (WEN0/1/2/3)

There are a possible total of four write enables available in this device

depending on the mode selected, one for each individual Queues in memory.

When the write enable input is LOW on the rising edge of WCLK in single data

rate, data is loaded on the rising edge of every WCLK cycle, provided the

device is not full and the write chip select (WCS) is enabled. The setup and

hold times are referenced with respect to the rising edge of WCLK only. When

the write enable input is LOW on the rising edge of WCLK in double data rate,

data is loaded into the selected Queue on the rising and falling edge of every

WCLK cycle, provided the device is not full and the write chip select (WCS)

is enabled. In this mode, the data setup and hold times are referenced with

respect to the rising and falling edge of WCLK. Note that WEN and WCS are

sampled only on the rising edge of WCLK in either data rate modes.

Data is stored in the Queues sequentially and independently of any ongoing

read operation. When the write enable(s) and write chip select(s) are HIGH,

no new data is written into the corresponding Queue on each WCLK cycle. The

four write enables operate independent of one another.

In Demux and Broadcast mode, only the WEN0 input is available. All other

write enables should be tied to VCC.

WRITE CHIP SELECT (WCS0/1/2/3)

There are a possible total of four write chip selects available in this device

depending on the mode selected, one for each individual Queues in memory.

The write chip selects disables all Write Port inputs for each individual Queue

if it is held HIGH. To perform normal write operations for each individual Queue,

the write chip select must be enabled, held LOW. The four write chip selects

are completely independent of one another.

When the write chip select is LOW on the rising edge of WCLK in single data

rate, data is loaded on the rising edge of every WCLK cycle, provided the

device is not full and the write enable (WEN) of the corresponding Queue is

LOW. When the write chip select is LOW on the rising edge of WCLK in double

data rate, data is loaded into the selected Queue on the rising and falling edge

of every WCLK cycle, provided the device is not full and the write enable (WEN)

of the corresponding Queue is LOW.

When the write chip select is HIGH on the rising edge of WCLK in single data

rate, the write port is disabled and no words are written on the rising edge of

WCLK into the Queue, even if WEN is LOW. If the write chip select is HIGH on

the rising edge of WCLK in double data rate, the write port is also disabled and

no words are written on the rising and falling edge of WCLK into the Queue,

even if WEN is LOW. Note that WCS is sampled on the rising edge of WCLK

only in either data rate modes.

In Demux and Broadcast mode, only the WCS0 input is available. All other

write chip selects should be tied to VCC.

WRITE DOUBLE DATA RATE (WDDR)

When the write double data rate (WDDR) pin is HIGH prior to master reset,

the write port will be set to double data rate mode. In this mode, all write

operations are based on the rising and falling edge of the write clocks, provided

that write enables and write chip selects are LOW for the rising clock edges.

In double data rate the write enable signals are sampled with respect to the rising

edge of write clock only, and a word will be written on both the rising and falling

edge of write clock regardless of whether or not the write enables are active

on the falling edge of write clock.

When WDDR is LOW, the write port will be set to single data rate mode. In

this mode, all write operations are based on only the rising edge of the write

clocks, provided that write enables and write chip selects are LOW during the

rising edge of write clock. This pin should be tied HIGH or LOW and cannot

toggle before or after master reset.

READ CLOCK (RCLK0/1/2/3)

There are a possible total of four read clocks available in this device

depending on the mode selected, each corresponding to the individual Queues

in memory. A read cycle is initiated on the rising and/or falling edge of the RCLK

input. If the read double data rate (RDDR) mode pin is tied HIGH, data will be

read on both the rising and falling edge of RCLK0/1/2/3, provided that REN0/

1/2/3 and RCS0/1/2/3 are enabled. If RDDR is tied LOW, data will be read

only on the rising edge of RCLK0/1/2/3 provided that REN0/1/2/3 and RCS0/

1/2/3 are enabled. The four read clocks are completely independent of one

another.

There is an associated data access time (tA) for the data to be read out of

the Queues. It is permissible to stop the read clocks. Note that while the read

clocks are idle, the EF/OR0/1/2/3 and PAE0/1/2/3 flags will not be updated

unless it is operating in asynchronous timing mode (PFM=0). The write and

read clocks can either be independent or coincident.

In Mux mode, only the RCLK0 input is available. All other read clock inputs

should be tied to GND.

READ ENABLE (REN0/1/2/3)

There are a possible total of four read enables available in this device

depending on the mode selected, one for each individual Queue in memory.

When the read enable input is LOW on the rising edge of RCLK in single data

rate, data will be read on the rising edge of every RCLK cycle, provided the

device is not empty and the read chip select (RCS) is enabled. The associated

data access time (tA) is referenced with respect to the rising edge of RCLK.

When the read enable input is LOW on the rising edge of RCLK in double data

rate, will be read on the rising and falling edge of every RCLK cycle, provided

the device is not empty and RCS is enabled. In this mode, the data access times

are referenced with respect to the rising and falling edges of RCLK. Note that

REN is sampled only on the rising edge of RCLK in either data rate modes.

Data is stored in the Queues sequentially and independently of any ongoing

write operation. When the read enable(s) and read chip select(s) are HIGH,

no new data is read on each RCLK cycle. The four read enables operate

independent of one another.

To prevent reading from an empty Queue in the IDT Standard mode, the

empty flag of each Queue will go LOW with respect to RCLK, when the total

number of words in the Queue has been read out, thus inhibiting further read

operations. Upon the completion of a valid write cycle, the empty flag will go

HIGH with respect to RCLK two cycles later, thus allowing another read to

occur, providing tSKEW of WCLK to RCLK is met.

In Mux mode, only the REN0 input is available. All other read enables should

be tied to VCC.

READ CHIP SELECT (RCS0/1/2/3)

There are a possible total of four read chip selects available in this device,

each corresponding to the individual Queue in memory. The read chip select

inputs provides synchronous control of the read port for each individual Queue.

When the read chip select is held LOW, the next rising edge of the correspond-

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

ing RCLK will enable the output bus. When the read chip select goes HIGH,

the next rising edge of RCLK will send the output bus into high-impedance and

prevent that RCLK from initiating a read, regardless of the state of REN. During

a master or partial Reset the read chip select input has no effect on the output

bus, output enable (OE[3:0]) is the only input that provides high-impedance

control of the output bus. If output enable is LOW, the data outputs will be active

regardless of read chip select until the first rising edge of RCLK after a reset is

complete. Afterwards if read chip select is HIGH the data outputs will go to high-

impedance. The four read chip selects are completely independent of one

another.

The read chip select inputs do not affect the updating of the flags. For example,

when the first word is written to any/all empty Queues, the empty flag(s) will still

go from LOW to HIGH based on a rising edge of the RCLK(s), regardless of

the state of the read chip select inputs. Also, when operating the Queue in FWFT

mode the first word written to any/all empty Queues will still be clocked through

to the output bus on the third rising edge of RCLK(s), regardless of the state of

read chip select inputs, assuming that the tSKEW parameter is met. For this reason

the user should pay extra attention to the read chip selects when a data word

is written to any/all empty Queues in FWFT mode. If the read chip select inputs

are HIGH when an empty Queue is written into, the first word will fall through

to the output register but will not be available on the outputs because they are

in high-impedance. The user must enable the read chip selects on the next rising

edge of RCLK to access this first word.

In Mux mode, only the RCS0 input is available. All other read chip select inputs

should be tied to VCC.

READ DOUBLE DATA RATE (RDDR)

When the read double data rate (RDDR) pin tied HIGH, the read port will be

set to double data rate mode, sampled during master reset. In this mode, all read

operations are based on the rising and falling edge of the read clocks, provided

that read enables and read chip selects are LOW. In double data rate mode,

the read enable signals are sampled with respect to the rising edge of read clock

only, and a word will be read from both the rising and falling edge of read clock

regardless of whether or not read enable and read chip select are active on

the falling edge of read clock.

When RDDR is tied LOW at master reset, the read port will be set to single

data rate mode. In this mode, all read operations are based on only the rising

edge of the read clocks, provided that read enables and read chip selects are

LOW during the rising edge of read clock. This pin should be tied HIGH or LOW

and cannot toggle before and after master reset.

OUTPUT ENABLE (OE0/1/2/3)

There are a possible total of four asynchronous output enables available in

this device, each corresponding to the individual Queues in memory. When the

output enable inputs are LOW, the output bus of each individual Queue become

active and drives the data currently in the output register. When the output enable

inputs (OE[3:0]) are HIGH, the output bus of each individual Queue goes into

high-impedance. During master or partial Reset the output enable is the only

input that can place the output data bus into high-impedance. During reset the

read chip select input has no effect on the output data bus. The four output enable

inputs are completely independent of one another.

In Mux mode, only the OE0 input is available. All other output enable inputs

should be tied to GND.

I/O SELECT (IOSEL)

The inputs and outputs of this device can be configured for either LVTTL or

HSTL/eHSTL operation. If the IOSEL pin is HIGH during master reset, then all

applicable LVTTL or HSTL signals will be configured for HSTL/eHSTL

operating voltage levels. To select between HSTL or eHSTL VREF must be

driven to 0.75V or 0.9V respectively.

If the IOSEL pin is LOW during master reset, then all applicable LVTTL or

HSTL signals will be configured for LVTTL operating voltage levels. In this

configuration VREF should be set to the static core voltage of 2.5V.

This pin should be tied HIGH or LOW and cannot toggle before or after master

reset. Please refer to table 5 for a list of applicable LVTTL/HSTL/eHSTL signals.

POWER DOWN (PD)

This device has a power down feature intended for reducing power

consumption for HSTL/eHSTL configured inputs when the device is idle for a

long period of time. By entering the power down state certain inputs can be

disabled, thereby significantly reducing the power consumption of the part. All

WEN and REN signals must be disabled for a minimum of four WCLK and RCLK

cycles before activating the power down signal. The power down signal is

asynchronous and needs to be held LOW throughout the desired power down

time. During power down, the following conditions for the inputs/outputs signals

are:

•All data in Queue(s) are retained.

•All data inputs become inactive.

•All write and read pointers maintain their last value before power down.

•All enables, chip selects, and clock input pins become inactive.

••

•All data outputs become inactive and enter high-impedance state.

••

•All flag outputs will maintain their current states before power down.

••

•All programmable flag offsets maintain their values.

••

•All echo clocks and enables will become inactive and enter

high-impedance state.

••

•The serial programming and JTAG port will become inactive and enter

high-impedance state.

••

•All setup and configuration CMOS static inputs are not affected, as these

pins are tied to a known value and do not toggle during operation.

All internal counters, registers, and flags will remain unchanged and maintain

their current state prior to power down. Clock inputs can be continuous and free-

running during power down, but will have no affect on the part. However, it is

recommended that the clock inputs be low when the power down is active. To

exit power down state and resume normal operations, disable the power down

signal by bringing it HIGH. There must be a minimum of 1µs waiting period before

read and write operations can resume. The device will continue from where it

had stopped, no form of reset is required after exiting power down state. The

power down feature does not provide any power savings when the inputs are

configured for LVTTL operation. However, it will reduce the current for I/Os that

are not tied directly to VCC or GND. See Figure 39, Power Down Operation

for the associated timing diagram.

SERIAL CLOCK (SCLK)

The serial clock is used to load data and read data from in the programmable

offset registers. Data from the serial input signal (FWFT/SI) can be loaded into

the offset registers on the rising edge of SCLK provided that the serial write

enable (SWEN) signal is LOW. Data can be read from the offset registers via

the serial data output (SDO) signal on the rising edge of SCLK provided that

SREN is LOW. The serial clock can operate at a maximum frequency of 10MHz.

The read operation is non-destructive. However, the write operation will

change the flag offsets on each SCLK rising edge as data shifts into the registers.

SERIAL WRITE ENABLE (SWEN)

The serial write enable input is an enable used for serial programming of the

programmable offset registers. It is used in conjunction with the serial input

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

(FWFT/SI) and serial clock (SCLK) when programming the offset registers.

When the serial write enable is LOW, data at the serial input is loaded into the

offset register, one bit for each LOW-to-HIGH transition of SCLK. When serial

write enable is HIGH, the offset registers retain the previous settings and no

offsets are loaded. Serial write enable functions the same way in both IDT

Standard and FWFT modes.

SERIAL READ ENABLE (SREN)

The serial read enable input is an enable used for reading the value of the

programmable offset registers. It is used in conjunction with the serial data output

(SDO) and serial clock (SCLK) when reading the offset registers. When the

serial read enable is LOW, data at the serial data output can be read from the

offset register, one bit for each LOW-to-HIGH transition of SCLK. When serial

read enable is HIGH, the reading of the offset registers will stop. Whenever serial

read enable (SREN) is activated values in the offset registers are read starting

from the first location in the offset registers. The SREN HIGH to LOW transition

copies the values in the offset registers directly into a serial scan out register.

SREN must be kept LOW in order to read the entire contents of the offset register.

If at any point SREN is toggled HIGH to LOW, another copy function from the

offset register to the serial scan out register will occur. Serial read enable

functions the same way in both IDT Standard and FWFT modes.

OUTPUTS:

DATA OUTPUT BUS (Q[39:0])

The data output bus can be 40, 20, or 10 bits wide in Mux mode. Q[39:0] are

data outputs for the 40-bit wide data bus, Q[19:0] are data outputs for 20-bit wide

data bus, and Q[9:0] are data outputs for the 10-bit wide data bus. In Demux

and Broadcast mode the output bus will be 10 bits wide for each of the four internal

Queues. Q[9:0] are dedicated to Queue 0, Q[19:10] are dedicated to Queue

1, Q[29:20] are dedicated to Queue 2, and Q[39:30] are dedicated to Queue

3. In FWFT mode, when switching from one Queue to another, the data of the

newly selected Queue will always be present on the output bus two cycles after

the next RCLK cycle after OS[1:0] is selected providing RCS is LOW regardless

of whether or not REN is active. Thus each of the four Queues can be accessed

on every RCLK cycle.

EMPTY/OUTPUT READY FLAG (EF/OR0/1/2/3)

There are four empty/output ready flags available in this device, each

corresponding to the individual Queues in memory. This is a dual-purpose pin

that is determined based on the state of the FWFT/SI pin during master reset

for selecting one of the two timing modes of this device. In the IDT Standard mode,

the empty flags are selected. When an individual Queue is empty, its empty flag

will go LOW, inhibiting further read operations from that Queue. When the empty

flag is HIGH, the individual Queue is not empty and valid read operations can

be applied. See Figure 24, 25, Read Cycle, Empty Flag and First Word Latency

Timing (IDT Standard Mode), for the relevant timing information. Also see Table

3 “Status Flags for IDT Standard Mode” for the truth table of the empty flags.

In FWFT mode, the output ready flags are selected. Output ready flags (OR)

go LOW at the same time that the first word written to an empty Queue appears

on the outputs, which is a minimum of three read clock cycles provided the RCLK

and WCLK meets the tSKEW parameter. OR stays LOW after the RCLK LOW-

to-HIGH transitions that shifts the last word from the Queue to the outputs. OR

goes HIGH when an enabled read operation is performed to an empty queue.

The previous data stays at the outputs, indicating the last word was read. Further

data reads are inhibited until a new word is on the bus when OR goes LOW again.

See Figure 21, 22, 23, Read Timing (FWFT Mode), for the relevant timing

information. Also see Table 4 “Status Flags for FWFT Mode” for the truth table

of the empty flags.

The empty/output ready flags are synchronous and updated on the rising

edge of RCLK. In IDT Standard mode, the flags are double register-buffered

outputs. In FWFT mode, the flags are triple register-buffered outputs. The four

empty flags operate independent of one another and always indicate the

respective Queue’s status.

COMPOSITE EMPTY/OUTPUT READY FLAG (CEF/COR)

This status pin is used to determine the empty state of the current Queue

selected. The composite empty/output ready flag represents the state of the

Queue selected on the read port, such that the user does not have to monitor

each individual Queues’ empty/output ready flags. The composite empty/output

ready flag is only available in Mux mode, since the output select bits (OS[1:0])

are used to select any one of the four Queues to read from.

The timing of the composite empty/output ready flag differs in IDT Standard

and FWFT modes. In IDT Standard mode, when switching from one Queue to

another, the composite empty flag will update to the status of the newly selected

Queue one RCLK cycle after the rising edge of RCLK that made the new Queue

selection. In FWFT mode, the composite output ready flag will update to the status

of the newly selected Queue on two clock cycles after the rising edge of RCLK

that made the new Queue selection. See Figures 26, 27 for the associated timing

diagram. See Table 3 and 4 “Status Flags for IDT Standard and FWFT Mode

“ for the truth table of the composite empty flag.

FULL/INPUT READY FLAG (FF/IR0/1/2/3)

There are four full/input ready flags available in this device, each corresponding

to the individual Queues in memory. This is a dual-purpose pin that is determined

based on the state of the FWFT/SI pin during master reset for selecting the two

timing modes of this device. In the IDT Standard mode, the full flags are selected.

When an individual Queue is full, its full flags will go LOW after the rising edge

of WCLK that wrote the last word, thus inhibiting further write operations to the

Queue. When the full flag is HIGH, the individual Queue is not full and valid write

operations can be applied. See Figures 14, 15, 16, Write Cycle, Full Flag and

First Word Latency Timing (IDT Standard Mode), for the associated timing

diagram. Also see Table 3 “Status Flags for IDT Standard Mode” for the truth

table of the full flags.

In FWFT mode, the input ready flags are selected. Input ready flags go LOW

when there is adequate memory space in the Queues for writing in data. The

input ready flags go HIGH after the rising edge of WCLK that wrote the last word,

when there are no free spaces available for writing in data. See Figures 17,

18, 19, Write Timing (FWFT Mode), for the associated timing information. Also

see Table 4 “Status Flags for FWFT Mode” for the truth table of the full flags. The

input ready status not only measures the depth of the Queues memory, but also

counts the presence of a word in the output register. Thus, in FWFT mode, the

total number of writes necessary to make IR HIGH is one greater than needed

to set FF = LOW in IDT Standard mode.

In Broadcast mode, when any one of the four full flags becomes asserted,

all write operations to every Queue will be disabled. This maintains data integrity

throughout all four Queues for comparison. In all other modes, the full flag will

only disable write operations to its corresponding Queue.

FF/IR is synchronous and updated on the rising edge of WCLK. FF/IR are

double register-buffered outputs. The four full flags operate independent of one

another, except in Broadcast mode.

To prevent data overflow in the IDT Standard mode, the full flag of each Queue

will go LOW with respect to WCLK, when the maximum number of words has

been written into the Queue, thus inhibiting further write operations. Upon the

completion of a valid read cycle, the full flag will go HIGH with respect to WCLK

two cycles later, thus allowing another write to occur, provided tSKEW has been

met.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

To prevent data overflow in the FWFT mode, the input ready flag of each

Queue will go HIGH with respect to WCLK, when the maximum number of words

has been written into the Queue, thus inhibiting further write operations. Upon

the completion of a valid read cycle, the input ready flag will go LOW with respect

to WCLK two cycles later, thus allowing another write to occur, provided tSKEW

has been met.

COMPOSITE FULL/INPUT READY FLAG (CFF/CIR)

This status pin is used to determine the full state of the current Queue selected.

The composite full/input ready flag represents the state of the Queue selected

on the write port, such that the user does not have to monitor each individual

Queues’ full/input ready flags. The composite full/input ready flag is only

available in both Demux and Broadcast modes. When switching from one

Queue to another, the composite full/input ready flag will update to the status of

the newly selected Queue one WCLK cycle after the rising edge of WCLK that

made the new Queue selection, regardless of which timing mode the device is

operating in. See Figure 28, Composite Full Flag for the relevant associated

timing diagram. See Table 3 and 4 “Status Flags for IDT Standard and FWFT

Mode “ for the truth table of the composite full flag

PROGRAMMABLE ALMOST EMPTY FLAG (PAE0/1/2/3)

There are four programmable almost empty flags available in this device,

each corresponding to the individual Queues in memory. The programmable

almost empty flag is an additional status flag that notifies the user when the Queue

is near empty. The user may utilize this feature as an early indicator as to when

the Queue will become empty. In IDT Standard mode, PAE will go LOW when

there are n words or less in the Queue. In FWFT mode, the PAE will go LOW

when there are n-1 words or less in the Queue. The offset “n” is the empty offset

value. The default setting for this value is stated in Table 2. Since there are four

internal Queues hence four PAE offset values, n0, n1, n2, and n3.

There are two timing modes available for the PAE flags, selectable by the state

of the Programmable Flag Mode (PFM) pin during master reset. If PFM is tied

HIGH, then synchronous timing mode is selected. If PFM is tied LOW, then

asynchronous timing mode is selected. In synchronous PAE configuration, the

PAE flag is updated on the rising edge of RCLK. In asynchronous PAE

configuration, the PAE flag is asserted LOW on the LOW-to-HIGH transitions of

the Read Clock (RCLK). PAE is reset to HIGH on the LOW-to-HIGH transitions

of the Write Clock (WCLK). See Figure 36, and 38, Synchronous and

Asynchronous Programmable Almost-Empty Flag Timing (IDT Standard and

FWFT mode), for the relevant timing information.

The four programmable almost empty flags operate independent of one

another.

PROGRAMMABLE ALMOST FULL FLAG (PAF0/1/2/3)

There are four programmable almost full flags available in this device, each

corresponding to the individual Queues in memory. The programmable almost

full flag is an additional status flag that notifies the user when the Queue is nearly

full. The user may utilize this feature as an early indicator as to when the Queue

will not be able to accept any more data and thus prevent data from being

dropped. In IDT Standard mode, if no reads are performed after master reset,

PAF will go LOW after (D-m) (D meaning the density of the particular device)

words are written to the Queue. In FWFT mode, PAF will go LOW after (D+1-

m) words are written to the Queue. The offset “m” is the full offset value. The default

setting for this value is stated in Table 2. Since there are four internal Queues

hence four PAF offset values, m0, m1, m2, and m3.

There are two timing modes available for the PAF flags, selectable by the state

of the Programmable Flag Mode (PFM) pin during master reset. If PFM is tied

HIGH, then synchronous timing mode is selected. If PFM is tied LOW, then

asynchronous timing mode is selected. In synchronous PAF configuration, the

PAF flag is updated on the rising edge of WCLK. In asynchronous PAF

configuration, the PAF flag is asserted LOW on the LOW-to-HIGH transitions

of the Write Clock (WCLK). PAF is reset to HIGH on the LOW-to-HIGH

transitions of the Read Clock (RCLK). See Figures 35 and 37, Synchronous

and Asynchronous Programmable Almost-Full Flag Timing (IDT Standard

and FWFT mode), for the relevant timing information.

The four programmable almost full flags operate independent of one

another.

TABLE 6 — TSKEW MEASUREMENT

Data Port Status Flags TSKEW Measurement Datasheet

Configuration Parameter

DDR Input EF/OR Negative Edge WCLK to tSKEW2

t o Positive Edge RCLK

DDR Output FF/IR Negative Edge RCLK to tSKEW2

Positive Edge WCLK

PAE Negative Edge WCLK to tSKEW3

Positive Edge RCLK

PAF Negative Edge RCLK to tSKEW3

Positive Edge WCLK

DDR Input EF/OR Negative Edge WCLK to tSKEW2

t o Positive Edge RCLK

SDR Output FF/IR Positive Edge RCLK to tSKEW1

Positive Edge WCLK

PAE Negative Edge WCLK to tSKEW3

Positive Edge RCLK

PAF Positive Edge RCLK to tSKEW3

Positive Edge WCLK

SDR Input EF/OR Positive Edge WCLK to tSKEW1

t o Positive Edge RCLK

DDR Output FF/IR Negative Edge RCLK to tSKEW2

Positive Edge WCLK

PAE Positive Edge WCLK to tSKEW3

Positive Edge RCLK

PAF Negative Edge RCLK to tSKEW3

Positive Edge WCLK

SDR Input EF/OR Positive Edge WCLK to tSKEW1

t o Positive Edge RCLK

SDR Output FF/IR Positive Edge RCLK to tSKEW1

Positive Edge WCLK

PAE Positive Edge WCLK to tSKEW3

Positive Edge RCLK

PAF Positive Edge RCLK to tSKEW3

Positive Edge WCLK

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

ECHO READ CLOCK (ERCLK0/1/2/3)

There are four echo read clock outputs available in this device, each

corresponding to their respective input read clocks in the Queue. The echo

read clock is a free-running clock output, that will always follow the RCLK input

regardless of the read enables and read chip selects. The ERCLK output

follows the RCLK input with an associated delay. This delay provides the user

with a more effective read clock source when reading data from the output bus.

This is especially helpful at high speeds when variables within the device may

cause changes in the data access times. These variations in access time may

be caused by ambient temperature, supply voltage, or device characteristics.

Any variations effecting the data access time will also have a corresponding

effect on the echo read clock output produced by the device, therefore the echo

read clock output level transitions should always be at the same position in time

relative to the data outputs. Note, that echo read clock is guaranteed by design

to be slower than the slowest data outputs. Refer to Figure 6, Echo Read Clock

and Data Output Relationship, Figure 27, Echo Read Clock and Read Enable

Operation in Double Data Rate Mode and Figure 28, Echo RCLK and Echo

REN

Operation for timing information. The four echo read clock outputs operate

independent of one another and are direct copies of their respective RCLK

inputs.

ECHO READ ENABLE (EREN0/1/2/3)

There are four echo read enable outputs available in this device, each

corresponding to the individual Queues in memory. The echo read enable

output is provided to be used in conjunction with the echo read clock and

provides the device receiving data from the Queue with a more effective

scheme for reading the Queues’ data. The echo read enable output is

controlled by internal logic that becomes active for the read clock cycle that a

new word is read out of the Queue. That is, a rising edge of read clock will cause

echo read enable to go LOW, if both read enable and read chip select are active

and the Queue is not empty. In other words, every cycle puts data on the output

bus and drives EREN output to the LOW.

Figure 6. Echo Read Clock and Data Output Relationship

NOTES:

1. REN is LOW. OE is LOW.

2. tERCLK > tA, guaranteed by design.

3. Qslowest is the data output with the slowest access time, tA.

4. Time, tD is greater than zero, guaranteed by design.

5. DDR mode clocks data on rising and falling edge of RCLK.

6157 drw12

ERCLK

SLOWEST

(3)

RCLK

ERCLK

(5)

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

TDO

TDI/

TMS

TCK

TRST

DOH

Notes to diagram:

t1 =

TCKLOW

t2 =

TCKHIGH

t3 =

tRST

(reset pulse width)

t4 = tRSR (reset recovery)

6157 drw13

t1t2

TCK

Figure 7. Standard JTAG Timing

NOTE:

1. 50pf loading on external output signals.

SYSTEM INTERFACE PARAMETERS

IDT72T55248

IDT72T55258

IDT72T55268

Parameter Symbol Test Conditions Min. Max. Units

Data Output tDO(1) -20ns

Data Output Hold tDOH(1) 0-ns

Data Input tDS trise=3ns 10 - ns

tDH tfall=3ns 10 -

Parameter Symbol Test

Conditions Min. Max. Units

JTAG Clock Input Period tTCK - 100 - ns

JTAG Clock HIGH tTCKHIGH -40-ns

JTAG Clock Low tTCKLOW -40-ns

JTAG Reset tRST -50-ns

JTAG Reset Recovery tRSR -50-ns

JTAG

AC ELECTRICAL CHARACTERISTICS

(vcc = 2.5V ± 5%; Tambient (Industrial) = 0°C to +85°C)

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

JTAG TIMING SPECIFICATIONS

(IEEE 1149.1 COMPLIANT)

The JTAG test port in this device is fully compliant with the IEEE Standard

Test Access Port (IEEE 1149.1) specifications. Five additional pins (TDI, TDO,

TMS, TCK and TRST) are provided to support the JTAG boundary scan

interface. Note that IDT provides appropriate Boundary Scan Description

Language program files for these devices.

The Standard JTAG interface consists of seven basic elements:

•Test Access Port (TAP)

•TAP controller

•Instruction Register (IR)

•Data Register Port (DR)

•Bypass Register (BYR)

•ID Code Register

•Flag Programming

The following sections provide a brief description of each element. For a

complete description refer to the IEEE Standard Test Access Port Specification

(IEEE Std. 1149.1-1990).

The Figure below shows the standard Boundary-Scan Architecture

Figure 8. JTAG Architecture

TEST ACCESS PORT (TAP)

The TAP interface is a general-purpose port that provides access to the

internal JTAG state machine. It consists of four input ports (TCLK, TMS, TDI,

TRST) and one output port (TDO).

THE TAP CONTROLLER

The TAP controller is a synchronous finite state machine that responds to

TMS and TCLK signals to generate clock and control signals to the Instruction

and Data Registers for capture and updating of data passed through the TDI

serial input.

In Pad

Incell

Core

Logic

Outcell

Out Pad

All outputs

All inputs

Eg: Dins, Clks

(BSDL file

describes the

chain order)

Bypass

Instruction

TA P

TMS

TDI

TCK

TRST

Instruction

Select

Enable

TDO

6157 drw14

Flag Offset Chain

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Refer to the IEEE Standard Test Access Port Specification (IEEE Std.

1149.1) for the full state diagram

All state transitions within the TAP controller occur at the rising edge of the

TCLK pulse. The TMS signal level (0 or 1) determines the state progression

that occurs on each TCLK rising edge. The TAP controller takes precedence

over the Queue operation and must be reset after power up of the device. See

TRST description for more details on TAP controller reset.

Test-Logic-Reset All test logic is disabled in this controller state enabling the

normal operation of the IC. The TAP controller state machine is designed in such

a way that, no matter what the initial state of the controller is, the Test-Logic-Reset

state can be entered by holding TMS at high and pulsing TCK five times. This

is the reason why the Test Reset (TRST) pin is optional.

Run-Test-Idle In this controller state, the test logic in the IC is active only if

certain instructions are present. For example, if an instruction activates the self

test, then it will be executed when the controller enters this state. The test logic

in the IC is idle otherwise.

Select-DR-Scan This is a controller state where the decision to enter the

Data Path or the Select-IR-Scan state is made.

Select-IR-Scan This is a controller state where the decision to enter the

Instruction Path is made. The Controller can return to the Test-Logic-Reset state

other wise.

Figure 9. TAP Controller State Diagram

Capture-IR In this controller state, the shift register bank in the Instruction

last two significant bits are always required to be “01”.

Shift-IR In this controller state, the instruction register gets connected

between TDI and TDO, and the captured pattern gets shifted on each rising

edge of TCK. The instruction available on the TDI pin is also shifted in to the

instruction register. TDO changes on the falling edge of TCK.

Exit1-IR This is a controller state where a decision to enter either the Pause-

IR state or Update-IR state is made.

Pause-IR This state is provided in order to allow the shifting of instruction

Exit2-DR This is a controller state where a decision to enter either the Shift-

IR state or Update-IR state is made.

Update-IR In this controller state, the instruction in the instruction register

scan chain is latched in to the register of the Instruction Register on every falling

edge of TCK. This instruction also becomes the current instruction once it is latched.

Capture-DR In this controller state, the data is parallel loaded in to the data

registers selected by the current instruction on the rising edge of TCK.

Shift-DR, Exit1-DR, Pause-DR, Exit2-DR and Update-DR These

controller states are similar to the Shift-IR, Exit1-IR, Pause-IR, Exit2-IR and

Update-IR states in the Instruction path.

Test-Logic

Reset

Run-Test/

Idle

Select-

DR-Scan

Select-

IR-Scan

111

Capture-IR

Capture-DR

Exit1-DR

Pause-DR

Exit2-DR

Update-DR

Exit1-IR

Exit2-IR

Update-IR

6157 drw15

Shift-DR

Shift-IR

Pause-IR

Input is

TMS

NOTES:

1. Five consecutive 1's at TMS will reset the TAP.

2. TAP controller resets automatically upon power-up.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

THE INSTRUCTION REGISTER

The instruction register (IR) is eight bits long and tells the device what

instruction is to be executed. Information contained in the instruction includes the

mode of operation (either normal mode, in which the device performs its normal

logic function, or test mode, in which the normal logic function is inhibited or

altered), the test operation to be performed, which of the four data registers is

to be selected for inclusion in the scan path during data-register scans, and the

source of data to be captured into the selected data register during Capture-DR.

TEST DATA REGISTER

The Test Data register contains three test data registers: the Bypass, the

Boundary Scan register and Device ID register.

These registers are connected in parallel between a common serial input

and a common serial data output.

The following sections provide a brief description of each element. For a

complete description, refer to the IEEE Standard Test Access Port Specification

(IEEE Std. 1149.1-1990).

TEST BYPASS REGISTER

The register is used to allow test data to flow through the device from TDI

to TDO. It contains a single stage shift register for a minimum length in the serial

path. When the bypass register is selected by an instruction, the shift register

stage is set to a logic zero on the rising edge of TCLK when the TAP controller

is in the Capture-DR state.

The operation of the bypass register should not have any effect on the

operation of the device in response to the BYPASS instruction.

THE BOUNDARY-SCAN REGISTER

The boundary-scan register (BSR) is 48 bits long. It contains one

boundary-scan cell (BSC) for each normal-function input pin and one BSC for

each normal-function I/O pin (one single cell for both input data and output data).

The BSR is used 1) to store test data that is to be applied externally to the device

output pins, and/or 2) to capture data that appears internally at the outputs of

the normal on-chip logic and/or externally at the device input pins.

THE DEVICE IDENTIFICATION REGISTER

The Device Identification Register is a Read Only 32-bit register used to

specify the manufacturer, part number and version of the device to be

determined through the TAP in response to the IDCODE instruction.

IDT JEDEC ID number is 0xB3. This translates to 0x33 when the parity is

dropped in the 11-bit Manufacturer ID field.

For the IDT72T55248/72T55258/72T55268, the Part Number field con-

tains the following values:

IDT72T55248/258/268 JTAG Device Identification Register

31(MSB) 28 27 12 11 1 0(LSB)

V ersion (4 bits) Part Number (16-bit) Manufacturer ID (11-bit)

0000 0033 (hex) 1

JTAG INSTRUCTION REGISTER

The Instruction register allows an instruction to be serially input into the

device when the TAP controller is in the Shift-IR state. The instruction is decoded

to perform the following:

•Select test data registers that may operate while the instruction is

current. The other test data registers should not interfere with chip

operation and the selected data register.

•Define the serial test data register path that is used to shift data between

TDI and TDO during data register scanning.

The Instruction Register is a 4 bit field (i.e. IR3, IR2, IR1, IR0) to decode

16 different possible instructions. Instructions are decoded as follows.

Hex Instruction Function

Value

0000 EXTEST Test external pins

0001 SAMPLE/PRELOAD Select boundary scan register

0002 IDCODE Selects chip identification register

0003 CLAMP Fix the output chains to scan chain values

0004 HIGH-IMPEDANCE Puts all outputs in high-impedance state

0007 OFFSET READ Read PAE/PAF offset register values

0008 OFFSET WRITE Write PAE/PAF offset register values

000F BYPASS Select bypass register

Private Several combinations are private (for IDT

internal use). Do not use codes other than

those identified above.

JTAG INSTRUCTION REGISTER DECODING

The following sections provide a brief description of each instruction. For

a complete description refer to the IEEE Standard Test Access Port Specification

(IEEE Std. 1149.1-1990).

EXTEST

The required EXTEST instruction places the device into an external

boundary-test mode and selects the boundary-scan register to be connected

between TDI and TDO. During this instruction, the boundary-scan register is

accessed to drive test data off-chip via the boundary outputs and receive test

data off-chip via the boundary inputs. As such, the EXTEST instruction is the

workhorse of IEEE. Std 1149.1, providing for probe-less testing of solder-joint

opens/shorts and of logic cluster function.

SAMPLE/PRELOAD

The required SAMPLE/PRELOAD instruction allows the device to remain in

a normal functional mode and selects the boundary-scan register to be

connected between TDI and TDO. During this instruction, the boundary-scan

functional data entering and leaving the device. This instruction is also used to

preload test data into the boundary-scan register before loading an EXTEST

instruction.

IDCODE

The optional IDCODE instruction allows the device to remain in its functional

mode and selects the optional device identification register to be connected

between TDI and TDO. The device identification register is a 32-bit shift register

containing information regarding the device manufacturer, device type, and

version code. Accessing the device identification register does not interfere with

the operation of the device. Also, access to the device identification register

should be immediately available, via a TAP data-scan operation, after power-

up of the device or after the TAP has been reset using the optional TRST pin

or by otherwise moving to the Test-Logic-Reset state.

Device Part# Field

IDT72T55248 04C9 (hex)

IDT72T55258 04CA (hex)

IDT72T55268 04CB (hex)

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

CLAMP

The optional CLAMP instruction sets the outputs of an device to logic levels

determined by the contents of the boundary-scan register and selects the one-

bit bypass register to be connected between TDI and TDO. Before loading this

instruction, the contents of the boundary-scan register can be preset with the

SAMPLE/PRELOAD instruction. During this instruction, data can be shifted

through the bypass register from TDI to TDO without affecting the condition of

the outputs.

HIGH-IMPEDANCE

The optional High-Impedance instruction sets all outputs (including two-state

as well as three-state types) of an device to a disabled (high-impedance) state

and selects the one-bit bypass register to be connected between TDI and TDO.

During this instruction, data can be shifted through the bypass register from TDI

to TDO without affecting the condition of the device outputs.

OFFSET READ

This instruction is an alternative to serial reading the offset registers for the

PAE/PAF flags. When reading the offset registers through this instruction, the

dedicated serial programming signals must be disabled.

OFFSET WRITE

This instruction is an alternative to serial programming the offset registers for

the PAE/PAF flags. When writing the offset registers through this instruction, the

dedicated serial programming signals must be disabled.

BYPASS

The required BYPASS instruction allows the device to remain in a normal

functional mode and selects the one-bit bypass register to be connected

between TDI and TDO. The BYPASS instruction allows serial data to be

transferred through the IC from TDI to TDO without affecting the operation of

the device.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

EF/OR

0/1/2/3

RSF

If FWFT = HIGH, OR = HIGH

If FWFT = LOW, EF = LOW

RSF

PAF0/1/2/3

RSF

Q[39-0]

RSF

OE = HIGH

OE = LOW

6157 drw16

OW[1:0]

(4)

IW[1:0]

(4)

FSEL[1:0]

(4)

PFM

(4)

HIGH = Synchronous PAE/PAF Timing

LOW = Asynchronous PAE/PAF Timing

MD[1:0]

(4)

RSS

HIGH = FWFT Mode

LOW = IDT Standard Mode

RDDR

(4)

WDDR

(4)

FWFT/SI

(4)

IOSEL

(4)

HIGH = Read/Write Double Data Rate

LOW = Read/Write Single Data Rate

HIGH = HSTL I/Os

LOW = LVTTL I/Os

RSS

If FWFT = LOW, FF = HIGH

If FWFT = HIGH, IR = LOW

FF/IR

0/1/2/3

PAE0/1/2/3

IS[1:0]

(4)

OS[1:0]

(4)

RSS

MRS

WEN

REN

RSS

SWEN,

SREN

RSS

RSR

Figure 10 . Master Reset

NOTES:

1. OE can be toggled during this period.

2. PRS should be HIGH during a MRS.

3. RCLK(s), WCLK(s) and SCLK(s) can be free running or idle.

4. The state of these pins are latched when the master reset pulse is LOW.

5. JTAG clock should not toggle during master reset.

6. RCS and WCS can be HIGH or LOW until the first rising edge of RCLK after master reset is complete.

7. EREN wave form is identical to REN, ERCLK wave form is identical to RCLK.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

WEN0/1,

REN0/1

RSS

PRS2/3

(1)

6157 drw17

FF/IR0/1

RSF

Current State

FF/IR2/3

RSF If FWFT = HIGH, FF = HIGH

If FWFT = LOW, IR = LOW

If FWFT = HIGH, CFF = HIGH

If FWFT = LOW, CIR = LOW

PAE0/1

RSF

Current State

PAE2/3

RSF

PAF0/1

RSF

Current State

PAF2/3

RSF

Q[39-0]

(2,4)

RSF OE = HIGH

OE = LOW

Current State

RSS

RSR

WEN2/3,

REN2/3

RSS

RSR

OS[1:0]

ENS

00 = Queue 0 01 = Queue 1

EF/OR0/1

RSF

Current State

EF/OR2/3

RSF If FWFT = HIGH, OR = HIGH

If FWFT = LOW, EF = LOW

If FWFT = HIGH, OR = HIGH

If FWFT = LOW, EF = LOW

RCLK0

123

PRS0/1

(1)

CEF/COR

RSF

Current State

If FWFT = HIGH, COR = HIGH

If FWFT = LOW, CEF = LOW

Output Data Queue 0 Output Data Queue 1

Figure 11 . Partial Reset for Mux mode

NOTES:

1 . During the output selection of two Queues, partial reset of the two Queues involved are prohibited.

2. During partial reset the high-impedance control of the output is provided by OE only.

3. PRS0/1 must go LOW after the fourth rising edge of RCLK0.

4. This is the output data from Queue0 and Queue1.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

WEN0,

REN0/1

RSS

PRS2/3

(1)

6157 drw18

Current State

RSF If FWFT = HIGH, FF = HIGH

If FWFT = LOW, IR = LOW

RSF

Current State

PAE2/3

RSF

PAF0/1

RSF

Current State

PAF2/3

RSF

Q[9-0]

(2,4)

Q[19-10]

(2,5)

RSF

OE = HIGH

OE = LOW

Current State

RSS

RSR

REN2/3

RSS

RSR

IS[1:0]

00 = Queue 0 01 = Queue 1

EF/OR0/1

RSF

Current State

EF/OR2/3

RSF If FWFT = HIGH, OR = HIGH

If FWFT = LOW, EF = LOW

If FWFT = HIGH, OR = HIGH

If FWFT = LOW, EF = LOW

FF/IR0/1

RSF

Current State

FF/IR2/3

If FWFT = HIGH, FF = HIGH

If FWFT = LOW, IR = LOW

PAE0/1

WCLK0

123

PRS0/1

(1)

CFF/CIR

RSF

Current State

If FWFT = HIGH, FF = HIGH

If FWFT = LOW, IR = LOW

Q[29-20]

(2,6)

Q[39-30]

(2,7)

RSF OE = HIGH

OE = LOW

Figure 12 . Partial Reset for Demux mode

NOTES:

1 . During the output selection of two Queues, partial reset of the two Queues involved are prohibited.

2. During partial reset the high-impedance control of the output is provided by OE only.

3. PRS0/1 must go LOW after the fourth rising edge of WCLK0.

4. This is the output data from Queue0.

5. This is the output data from Queue1.

6. This is the output data from Queue2.

7. This is the output data from Queue3.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 13. Partial Reset for Broadcast mode

WCLK0

REN

(2)

0/1/2/3

tRSS

PRS0/1/2/3

6157 drw19

(1)

WEN0

EF/OR0/1/2/3

tRSF If FWFT = HIGH, OR = HIGH

If FWFT = LOW, EF = LOW

tRSS

FF/IR0/1/2/3

tRSF If FWFT = LOW, FF = HIGH

If FWFT = HIGH, IR = LOW

PAE0/1/2/3

tRSF

PAF0/1/2/3

tRSF

Q[39-0]

(3,4)

tRSF OE = HIGH

OE = LOW

CFF/CIR

tRSF If FWFT = LOW, FF = HIGH

If FWFT = HIGH, IR = LOW

NOTES:

1. If the write port is configured in double data rate, partial reset must be initiated after the falling edge of WCLK0 to ensure falling edge data is written into memory.

2. Only the read enable of the Queue involved in partial reset need to be HIGH.

3. During partial reset the high-impedance control of the outputs is provided by OE only.

4 . Only affects the output of the Queue partial reset is applied to.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 14. Write Cycle and Full Flag Timing (Mux mode, IDT Standard mode, SDR to SDR) x10 In to x40 Out

OS[1:0]

00=Queue 0

Previous Word+1 Queue 0

6157 drw20

RCLK0

REN0

01=Queue 1

Q[39:0]

(4) Previous Word Queue 0

Word 0 Queue 1

Word 0 Queue 2

Word 1 Queue 2

ENS

ENH

10=Queue 2

WCLK1

WEN0

D[9:0]

SKEW

(3)

ENS

No Write

WD-1

WCLK0

No Write

WEN1

FF0

WFF

FF1

D[19:10]

WD-1

ENH

WFF

SKEW

(2)

NOTES:

1. WCS0, WCS1 are LOW.

2. This is the skew between RCLK0 and WCLK0 for Queue0.

3. This is the skew between RCLK0 and WCLK1 for Queue1.

4 . There is a two-stage pipeline so each read appears in the data bus two cycles or three rising edges of RCLK later.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK2

SKEW1

Din[9:0]

WEN0

NO WRITE

WCLK0

NO WRITE

ENS

Word D

Word D-1 Word D+1

Word D+2

Word 1

Q[29:20]

6157 drwA

Previous Data in Output Register

FF2

WFF

FF1

WFF

FF0

SKEW1

REN2

ENS

RCLK1

REN1

ENS

RCLK0

REN0

ENS

Word 2

Word 3

Word 4

Word 5

Word 6

Word 7

Word 1

Word 2

Word 3

Word 4

Q[19:10]

Previous Data in Output Register

Word 1

Q[9:0]

Previous Data in Output Register

1212

Figure 15. Write Cycle and Full Flag Timing (Broadcast Write mode, IDT Standard mode, SDR to SDR) x10 In to x10 Out

NOTE:

1. WCS0, RCS0/1/2, and OE0/1/2 are LOW.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK2

SKEW1

Din[9:0]

(2)

Word X Queue X

Word X-1 Queue X

Q[29:20]

6157 drwB

Previous Data in Output Register

FF2

WFF

FF1

FF0

REN2

ENS

RCLK1

REN1

ENS

RCLK0

REN0

ENS

Word 1

Word 2

Word 3

Word 4

Word 5

Word 2

Word 3

Word 4

Q[19:10]

Previous Data in Output Register

Q[9:0]

Previous Data in Output Register

WEN0

WCLK0

NO WRITE

10 = Queue 2

IS[1:0]

01 = Queue 1 00 = Queue 0 10 01 00

ENH

ENS

10 01

Word 0 Queue 2 Word 0 Queue 1

WFF

SKEW1

Word 1

Word 2

Word 3Word 1

ENH

12 12

Word 1 Queue 1 Word 0 Queue 0

Figure 16. Write Cycle and Full Flag Timing (Demux mode, IDT Standard mode, SDR to SDR) x10 In to x10 Out

NOTES:

1. WCS0, RCS0/1/2, and OE0/1/2 are LOW.

2. There is a two-stage pipeline so each read appears in the queue two cycles or three rising edges of WCLK later.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK0

SKEW1

Word 1

Q[9:0]

6157 drwC

Previous Data in Output Register

Word 2

Word 3 Word 4

Q[19:10]

REN0

ENS

OR0t

WFF

OR1

Din[9:0]

WEN0

WCLK0

ENS

Word 2

Word 1

ENH

Word 3 Word 4

D[19:10]

WEN1

WCLK1

ENS

Word 2

Word 1

ENH

Word 3 Word 4

12 3

00 = Queue 0

OS[1:0]

01 = Queue 1

ENS

Word 1

Previous Data in Output Register Word 2

Figure 17. Write Timing (Mux mode, FWFT mode, SDR to SDR) x10 In to x10 Out

NOTE:

1. WCS0/1, and OE0/1 are LOW.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK3

SKEW1

Word 1

Q[39:30]

6157 drwD

Previous Data in Output Register

Word 2

Word 3 Word 4

Q[9:0]

REN3

ENS

12 3

Word 1

Previous Data in Output Register Word 2

OR3t

REF

OR0

Din[9:0]

WEN0

WCLK0

ENS

Word 2

Word 1 Word 3 Word 4 Word 5 Word 6 Word 7

REF

RCLK0

SKEW1

REN0

ENS

12 3

Figure 18. Write Timing (Broadcast Write mode, FWFT mode, SDR to SDR) x10 In to x10 Out

NOTE:

1. WCS0, RCS0/3, and OE0/3 are LOW.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK2

SKEW1

6157 drwE

Word 2

Word 3

Q[29:20]

Previous Data in Output Register

Q[19:10]

Previous Data in Output Register

Word 1

Word 2

Word 3Word 1

REN2

RCLK1

REN1

12 3

Din[9:0]

(2)

OR2

OR1

ENS

WEN0

WCLK0

10 = Queue 2

IS[1:0]

01 = Queue 1 10 01 10 01

ENS

10 01

REF

Word X Queue X

ENH

Word 0 Queue 2 Word 0 Queue 1 Word 1 Queue 2 Word 1 Queue 1 Word 2 Queue 2 Word 2 Queue 1

REF

SKEW1

12 3

Figure 19. Write Timing (Demux mode, FWFT mode, SDR to SDR) x10 In to x10 Out

NOTES:

1. WCS0, RCS1/2, and OE1/2 are LOW.

2. There is a two-stage pipeline so each read appears in the queue two cycles or three rising edges of WCLK later.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK0

REN0

REF

WEN3

D[39:30]

Q[39:0]

ENS

Wx-3

No Read No Read

Wx-1

CEF

REF

WCLK3

SKEW

ENS

ENH

Wx (Byte 0)

6157 drw22

Wx-2

Wx (Byte 1)

Wx (Byte 2)

Wx (Byte 3)

Figure 20. Read Cycle, Empty Flag and First Word Latency (Mux mode, IDT Standard mode, SDR to SDR) x10 In to x40 Out

NOTES:

1. RCS0, WCS3, OE3 are LOW.

2. OS[1:0] = 11.

3. Wx (Byte 0) = Q[9:0], Wx (Byte 1) = Q[19:10], Wx (Byte 2) = Q[29:20], Wx (Byte 3) = Q[39:30].

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK1

SKEW1

6157 drwF

Q[19:10] W1 W2

REN1

Din[9:0]

IR0

WEN0

WCLK0

WFF

RCLK0

Q[9:0] W1

REN0

REF

Figure 21. Read Timing (Broadcast Write mode, FWFT mode, SDR to SDR) x10 In to x10 Out

NOTES:

1. WCS0, RCS0/1, and OE0/1 are LOW.

2. Q[39:10] = 0.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK0

6157 drwG

Q[9:0]

W1 W2

REN0

IR0

WFF

ENS

SKEW1

D[9:0]

WEN0

WCLK0

ENH

ENS

6157 drwH

W1 Byte D

ENS

RCLK0

Q[9:0]

REN0

IR0

WFF

SKEW1

D[19:0]

WEN0

WCLK0

ENH

ENS

W1 Byte 1 W2 Byte D W2 Byte 1

Figure 23. Read Timing (Demux mode, FWFT mode, SDR to SDR) x20 In to x10 Out

NOTES:

1. WCS0, RCS0, and OE0 are LOW.

2. IS[1:0] = 00. Q[39:10] = 0.

3. WD is a 20-bit word. Q[9:0] = Byte 0, Q[19:10] = Byte 1.

Figure 22. Read Timing (Mux mode, FWFT mode, SDR to SDR) x10 In to x10 Out

NOTES:

1. WCS0, RCS0, and OE0 are LOW.

2. OS[1:0] = 00.

3. Q[39:10] = 0.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK0

REN0

EF1

Q[19:10]

WCLK0

WEN0

D[19:0]

IS[1:0]

REN1

RCLK1

EF0

Q[9:0]

SKEW1

REF

6157 drwI

Previous Data in Output Register

Byte 0

01 = Queue 1 00 = Queue 0 01

ENS

ENH

WX Byte 0 - Byte 1

ENS

SKEW1

Byte 1

ENS

REF

Previous Data in Output Register

Byte 0

Byte 1

ENS

WX Byte 0 - Byte 1

Figure 24. Read Cycle, Empty Flag and First Word Latency (Demux mode, IDT Standard mode, SDR to SDR) x20 In to x10 Out

NOTES:

1. WCS0, RCS0/1, and OE0/1 are LOW.

2. WX is a 20-bit word. LSB = Byte 0, MSB = Byte 1.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

RCLK1

REN1

EF2

Q[29:20]

WCLK0

WEN0

D[39:0]

6157 drwJ

WX Byte 0 - Byte 3

REN2

RCLK2

EF1

Q[19:10]

SKEW1

REF

Previous Data in Output Register

WX Byte 0

ENS

WX Byte 3

ENS

REF

Previous Data in Output Register

WX Byte 0

WX Byte 1

ENS

REF

WX Byte 2

WX Byte 1

ENS

NO READ

Figure 25. Read Cycle, Empty Flag and First Word Latency (Broadcast Write mode, IDT Standard mode, SDR to SDR) x40 In to x10 Out

NOTES:

1. WCS0, RCS1/2, and OE1/2 are LOW.

2. WX is a 40-bit word. LSB = Byte 0-Byte 1, MSB = Byte 2-Byte 3.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

REN0

RCLK0

6157 drw23

12 3

Q[39:0](3) Word D-1 Queue 1

OS[1:0] 01 = Queue 1 11 = Queue 3

Word D Queue 1

tENS

Next Word Queue 3

tREF

CEF

tREF tREF

No Read

tDS

Figure 26. Composite Empty Flag (Mux mode, IDT Standard mode, SDR to SDR) x10 In to x40 Out

NOTES:

1. RCS0 and OE0 are LOW.

2. EF3 is HIGH.

3. Word D-1 is the second and last word in Queue 1. Word D is the last word in Queue 1.

REN0

OR1

RCLK0

6157 drw24

12 3

Q[39:0]

(3)

Word

D-1

Queue 1

OS[1:0] 01 = Queue 1 11 = Queue 3

Word D Queue 1

tENS

Next Word Queue 3

tREF

COR

tREFtREF

Figure 27. Composite Output Ready Flag (Mux mode, FWFT mode, SDR to SDR) x10 In to x40 Out

NOTES:

1. RCS0 and OE0 are LOW.

2. OR3 is LOW.

3. Word D-1 is the second and last word in Queue 1. Word D is the last word in Queue 1.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

WEN0

WCLK0

6157 drw25

CFF

tWFF

12 3

IS[1:0] 01 = Queue 1 11 = Queue 3

tENS

No Write

D[19:0] Word D Queue 1

tDS tDH

tDH

Word D Queue 3 Word D+1 Queue 3

tWFF

tDS tDH tDS

Figure 28. Composite Full Flag (Demux mode, IDT Standard mode, SDR to SDR) x20 In to x10 Out

NOTES:

1. WCS0 is LOW.

2. FF3 is HIGH.

WEN0

WCLK0

6157 drw26

CIR

WFF

12 3

IS[1:0]

ENS

No Write

D[19:10]

(3)

IR1

WFF

Word D+1 Queue 1

Word D Queue 3 Word D+1 Queue 3

01 = Queue 1 11 = Queue 3

WFF

Figure 29. Composite Input Ready Flag (Demux mode, FWFT mode, SDR to SDR) x20 In to x10 Out

NOTES:

1. WCS0 is LOW.

2. IR3 is LOW.

3. Word D is the first word written and fell through to output (FWFT).

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 30. Echo Read Clock and Read Enable Operation (Mux/Demux/Broadcast mode, IDT Standard mode, DDR to DDR) x10 In to x10 Out

NOTES:

1. The EREN0 output is “or gated” to RCS0 and REN0 and will follow these inputs provided that the Queue is not empty. If the Queue is empty, EREN0 will go HIGH to indicate that there is no new word available.

2. The EREN0 output is synchronous to RCLK0.

3. OE0 = LOW, WDDR = HIGH, and RDDR = HIGH.

4. Q[39:10] = 0.

5. The truth table for EREN is shown below:

RCLK0

REN0

EREN0

ERCLK0

EF0

RCS0

tENS

tREF

tERCLK

tENH

Q[9:0]

tENS

tENH

tCLKEN tCLKEN tCLKEN tCLKEN

tOLZ tA

tCLKEN

tAtOLZ

tOLZ tA

tAtAtA

WD-10 WD-9 WD-8 WD-6 WD-5 WD-4 WD-3 WD-2 Last Word W

6157 drw27

tCLKEN

WD-7 WD-6

WD-1

tENS

NO Read NO Read

RCLK EF RCS REN EREN

↑1000

↑1011

↑1101

↑1111

↑0XX1

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 31. Echo RCLK and Echo Read Enable Operation (Mux/Demux/Broadcast mode, FWFT mode, SDR to SDR)

NOTE:

1. The O/P Register is the internal output register. Its contents are available on the Qn output bus only when RCS0 and OE0 are both active, LOW, that is the bus is not in

High-Impedance state.

2. OE0 is LOW.

3. Q[39:10] = 0.

Cycle:

a&b. At this point the Queue is empty, OR0 is HIGH.

RCS0 and REN0 are both disabled, the output bus is High-Impedance.

c. Word Wn+1 falls through to the output register, OR0 goes active, LOW.

RCS0 is HIGH, therefore the Qn outputs are High-Impedance. EREN0 goes LOW to indicate that a new word has been placed into the output register.

d. EREN0 goes HIGH, no new word has been placed on the output register into this cycle.

e. No Operation.

f. RCS0 is LOW on this cycle, therefore the Qn outputs go to Low-Impedance and the contents of the output register (Wn+1) are made available.

NOTE: In FWFT mode it is important to take RCS0 active LOW at least one cycle ahead of REN0, this ensures the word (Wn+1) currently in the output register is made

available for at least one cycle, otherwise Wn+1 will overwritten by Wn+2.

g. REN0 goes active LOW, this reads out the second word, Wn+2.

EREN0 goes active LOW to indicate a new word has been placed into the output register.

h. Word Wn+3 is read out, EREN0 remains active, LOW indicating a new word has been read out.

NOTE: Wn+3 is the last word in the Queue.

i. This is the next enabled read after the last word, Wn+3 has been read out. OR0 flag goes HIGH and EREN0 goes HIGH to indicate that there is no new word available.

4. OE0 is LOW, WDDR = LOW, and RDDR = LOW.

5. The truth table for EREN is shown below:

Q[9:0]

O/P

(1)

Reg.

REF

OR0

6157 drw28

RCSLZ

REN0

ENS

ENH

RCS0

ENS

RCLK0

abcdefghi

n+1

WCLK0

WEN0

D[9:0]

SKEW1

ENS

ENH

n+2

n+3

ERCLK0

EREN0

CLKEN

n+1

n+2

n+3

REF

n+1

n+2

n+3

Last Word

ERCLK

HIGH-Z

ENH

RCLK OR RCS REN EREN

↑0000

↑0011

↑0101

↑0111

↑1XX1

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

6157 drw29

RCLK0

REN0

ERCLK

ERCLK0

RCS0

ENS

EREN0

CLKEN

EF0

REF

Q[9:0]

OLZ

D-1

D Last Word

D-2

D-3

D-4

Figure 32. Echo Read Clock and Read Enable Operation (Mux/Demux/Broadcast mode, IDT Standard mode, SDR to SDR) x10 In to x10 Out

NOTES:

1. The EREN0 output is “or gated” to RCS0 and REN0 and will follow these inputs provided that the Queue is not empty. If the Queue is empty, EREN0 will go HIGH to indicate that

there is no new word available.

2. The EREN0 output is synchronous to RCLK0.

3. OE0 = LOW, WDDR = HIGH, and RDDR = HIGH.

4. Q[39:10] = 0.

5. The truth table for EREN is shown below:

RCLK EF RCS REN EREN

↑1000

↑1011

↑1101

↑1111

↑0XX1

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 33. Loading of Programmable Flag Registers (IDT Standard and FWFT modes)

SENH

SDH

SCLK

SWEN

FWFT/SI

6157 drw30

EMPTY OFFSET 3 FULL OFFSET 3

SENS

SDS

BIT

(1)

BIT 1

SCL

SCKH

SCKL

BIT 1

(LSB)

EMPTY OFFSET 0 FULL OFFSET 0

BIT 1

(LSB)

BIT

(1)

BIT

(1)

BIT

(1)

(MSB)(MSB)

Figure 34. Reading of Programmable Flag Registers (IDT Standard and FWFT modes)

SCLK

SREN

SDO

6157 drw31

EMPTY OFFSET 3 FULL OFFSET 3

SENS

SOA

SEN

BIT X

(1)

SENH

SCLK

SCKH

SCKL

BIT 0 BIT 0 BIT X

(1)

BIT X

(1)

SOA

BIT 0

EMPTY OFFSET 0 FULL OFFSET 0

BIT 0

(LSB)

BIT X

(1)

(MSB) (LSB) (MSB)

NOTE:

1 . If IW/OW = x40, X = 104 for the IDT72T55248, X = 112 for the IDT72T55258, X = 120 for the IDT72T55268.

If IW/OW = x20, X = 112 for the IDT72T55248, X = 120 for the IDT72T55258, X = 128 for the IDT72T55268.

If IW/OW = x10, X = 120 for the IDT72T55248, X = 128 for the IDT72T55258, X = 136 for the IDT72T55268.

NOTE:

1 . If IW/OW = x40, X = 104 for the IDT72T55248, X = 112 for the IDT72T55258, X = 120 for the IDT72T55268.

If IW/OW = x20, X = 112 for the IDT72T55248, X = 120 for the IDT72T55258, X = 128 for the IDT72T55268.

If IW/OW = x10, X = 120 for the IDT72T55248, X = 128 for the IDT72T55258, X = 136 for the IDT72T55268.

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

WCLK

WEN0

PAF0

RCLK0

REN0

6157 drw32

1212

D - m0 words in Queue(1)

D - (m0 +1) words in Queue(1)

ENH

ENS

PAFS

ENS

ENH

CLKL

SKEW2

(3)

PAFS

CLKL

WCLK0

WEN0

PAE0

RCLK0

12 12

REN06157 drw33

n0 words in Queue

ENS

SKEW2(4)

ENH

PAES

n0 + 1 words in Queue

(2)

n0 + 2 words in Queue

(3)

ENS

ENH

CLKH

CLKL

NOTES:

1. m0 = PAF0 offset .

2. D = maximum Queue depth. For density of Queue with bus-matching, refer to the bus-matching section on page 19.

3. tSKEW2 is the minimum time between a rising RCLK0 edge and a rising WCLK0 edge to guarantee that PAF0 will go HIGH (after one WCLK0 cycle plus tPAFS). If the time

between the rising edge of RCLK0 and the rising edge of WCLK0 is less than tSKEW2, then the PAF0 deassertion time may be delayed one extra WCLK0 cycle.

4. PAF0 is asserted and updated on the rising edge of WCLK0 only.

5. Select this mode by setting PFM HIGH during Master Reset.

6. RCS0 = LOW, WCS0 = LOW, WDDR = LOW, and RDDR = LOW.

Figure 35. Synchronous Programmable Almost-Full Flag Timing

(Mux/Demux/Broadcast mode, IDT Standard and FWFT mode, SDR to SDR) x10 In to x10 Out

NOTES:

1. The timing diagram shown is for Queue0. Queues1-3 exhibit the same behavior.

2 . n0 = PAE0 offset.

3. For IDT Standard mode

4. For FWFT mode.

tSKEW2 is the minimum time between a rising WCLK0 edge and a rising RCLK0 edge to guarantee that PAE

will go HIGH (after one RCLK0 cycle plus tPAES). If the time between

the rising edge of WCLK0 and the rising edge of RCLK0 is less than tSKEW2, then the PAE

deassertion may be delayed one extra RCLK0 cycle.

6. PAE0 is asserted and updated on the rising edge of WCLK0 only.

7. Select this mode by setting PFM HIGH during Master Reset.

8. RCS0 = LOW, WCS0 = LOW, WDDR = LOW, and RDDR = LOW.

Figure 36. Synchronous Programmable Almost-Empty Flag Timing

(Mux/Demux/Broadcast mode, IDT Standard and FWFT mode, SDR to SDR) x10 In to x10 Out

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

WCLK0

WEN0

PAF0D - (m0 + 1) words

in Queue

RCLK0

tPAFA

REN0

6157 drw34

D - m0 words

in Queue

D - (m0 + 1) words in Queue

tENS

tPAFA

tENH

tENS

tCLKLtCLKH

WCLK0

WEN0

PAE0

n0 words in Queue

(2)

n0 + 1 words in Queue

(3)

RCLK0

REN0

6157 drw35

PAEA

n0 + 1 words in Queue

(2)

n 0+ 2 words in Queue

(3)

PAEA

ENS

ENH

CLKL

CLKH

n0 words in Queue

(2)

n0 + 1 words in Queue

(3)

NOTES:

1. m0 = PAF0 offset.

2. D = maximum Queue depth. For density of Queue with bus-matching, refer to the bus-matching section on page 19.

3. PAF0 is asserted to LOW on WCLK0 transition and reset to HIGH on RCLK0 transition.

4. Select this mode by setting PFM LOW during Master Reset.

5. RCS0 is LOW, WCS0 is LOW, WDDR = LOW, and RDDR = LOW.

Figure 37. Asynchronous Programmable Almost-Full Flag Timing

(Mux/Demux/Broadcast mode, IDT Standard and FWFT mode, SDR to SDR) x10 In to x10 Out

NOTES:

1 . n0 = PAE0 offset.

2. For IDT Standard Mode.

3. For FWFT Mode.

4. PAE0 is asserted LOW on RCLK0 transition and reset to HIGH on WCLK0 transition.

5. Select this mode by setting PFM LOW during Master Reset.

6. RCS0 is LOW, WCS0 is LOW, WDDR = LOW, and RDDR = LOW.

Figure 38. Asynchronous Programmable Almost-Empty Flag Timing

(Mux/Demux/Broadcast mode, IDT Standard and FWFT mode, SDR to SDR) x10 In to x10 Out

IDT72T55248/72T55258/72T55268 2.5V QuadMux DDR Flow-Control Device with

Mux/Demux/Broadcast functions 8K x 40 x 4, 16K x 40 x 4 and 32K x 40 x 4

COMMERCIAL AND INDUSTRIAL

TEMPERATURE RANGES

MARCH 22, 2005

Figure 39. Power Down Operation

6157 drw36

WCLK

WEN

D[39:0]

D10

D11

D13

RCLK

REN

ERCLK

PDHZ

(7)

PDLZ

(2)

PDL

PDH

(2)

PDH

(2)

(8)

Hi-Z

EREN

Q[39:0]

ERCLK

EREN

1234

(1)

1µs

EREN

D12

NOTES:

1. All read and write operations must have ceased a minimum of 4 WCLK and 4 RCLK cycles before power down is asserted.

2. When the PD input becomes deasserted, there will be a 1µs waiting period before read and write operations can resume.

All input and output signals will also resume after this time period.

3. Set-up and configuration static inputs are not affected during power down.

4. Serial programming and JTAG programming port are inactive during power down.

5. RCS = 0, WCS = 0 and OE = 0. These signals can toggle during and after power down.

6. All flags remain active and maintain their current states.

7. During power down, all outputs will be in high-impedance.

CORPORATE HEADQUARTERS for SALES: for Tech Support:

6024 Silver Creek Valley Road 800-345-7015 or 408-284-8200 408-360-1533

San Jose, CA 95138 fax: 408-284-2775 email: Flow-Controlhelp@idt.com

www.idt.com

Plastic Ball Grid Array (PBGA, BB324-1)

Commercial (0°C to +70°C)

Industrial (-40°C to +85°C)

Low Power

6157 drwlast

Commercial Only

Commercial and Industrial

IDT XXXXX

Device Type

Power

Speed

Package

Process /

Temperature

Range

BLANK

I(1)

72T55248 8,192 x 40 x 4  2.5V QuadMux DDR Flow-Control Device

72T55258 16,384 x 40 x 4  2.5V QuadMux DDR Flow-Control Device

72T55268 32,768 x 40 x 4  2.5V QuadMux DDR Flow-Control Device

Clock Cycle Time (t

CLK

)

Speed in Nanoseconds

6-7

ORDERING INFORMATION

DATASHEET DOCUMENT HISTORY

12/01/2003 pgs. 1, 8, 17, and 36.

03/22/2005 pgs. 4, 6, 9, 15-18, 21-24, 32, 34, and 65.