INTEGRATED CIRCUITS DATA SHEET TEA5768HL Low-power FM stereo radio for handheld applications Preliminary specification Supersedes data of 2002 Sep 13 2003 Nov 06 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL CONTENTS 1 FEATURES 2 GENERAL DESCRIPTION 3 ORDERING INFORMATION 4 QUICK REFERENCE DATA 5 BLOCK DIAGRAM 6 PINNING 7 FUNCTIONAL DESCRIPTION 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 7.9 Low-noise RF amplifier FM mixer VCO Crystal oscillator PLL tuning system RF AGC IF filter FM demodulator Level voltage generator and analog-to-digital converter IF counter Soft mute MPX decoder Signal dependent mono to stereo blend Signal dependent AF response Software programmable ports 7.10 7.11 7.12 7.13 7.14 7.15 8 I2C-BUS AND BUS-CONTROLLED FUNCTIONS 8.1 8.1.1 8.1.2 8.2 8.3 8.4 8.5 I2C-bus specification Data transfer Power-on reset I2C-bus protocol Writing data Reading data Bus timing 2003 Nov 06 9 LIMITING VALUES 10 THERMAL CHARACTERISTICS 11 DC CHARACTERISTICS 12 AC CHARACTERISTICS 13 INTERNAL PIN CONFIGURATION 14 APPLICATION INFORMATION 15 PACKAGE OUTLINE 16 SOLDERING 16.1 Introduction to soldering surface mount packages Reflow soldering Wave soldering Manual soldering Suitability of surface mount IC packages for wave and reflow soldering methods 16.2 16.3 16.4 16.5 2 17 DATA SHEET STATUS 18 DEFINITIONS 19 DISCLAIMERS 20 PURCHASE OF PHILIPS I2C COMPONENTS Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications 1 TEA5768HL FEATURES * High sensitivity due to integrated low-noise RF input amplifier * FM mixer for conversion to IF of the US/Europe (87.5 to 108 MHz) and Japanese (76 to 91MHz) FM band * Soft mute, SNC and HCC can be switched off via the I2C-bus * Preset tuning to receive Japanese TV audio up to 108 MHz * Adjustment-free stereo decoder * RF Automatic Gain Control (AGC) circuit * Autonomous search tuning function * LC tuner oscillator operating with low cost fixed chip inductors * Standby mode * Two software programmable ports * FM IF selectivity performed internally * Bus enable line to switch the bus input and output lines into 3-state mode. * No external discriminator needed due to fully integrated FM demodulator * Crystal reference frequency oscillator; the oscillator operates with a 32.768 kHz clock crystal or with a 13 MHz crystal and with an externally applied 6.5 MHz reference frequency 2 GENERAL DESCRIPTION The TEA5768HL is a single-chip electronically tuned FM stereo radio for low-voltage application with fully integrated IF selectivity and demodulation. The radio is completely adjustment-free and only requires a minimum of small and low cost external components. The radio can be tuned to the European, US and Japanese FM bands. * PLL synthesizer tuning system * I2C-bus * 7-bit IF counter output via the I2C-bus * 4-bit level information output via the I2C-bus * Soft mute * Signal dependent mono to stereo blend [Stereo Noise Cancelling (SNC)] * Signal dependent High Cut Control (HCC) 3 ORDERING INFORMATION TYPE NUMBER TEA5768HL 2003 Nov 06 PACKAGE NAME LQFP32 DESCRIPTION plastic low profile quad flat package; 32 leads; body 7 x 7 x 1.4 mm 3 VERSION SOT358-1 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 4 QUICK REFERENCE DATA VCCA = VCC(VCO) = VCCD. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VCCA analog supply voltage 2.5 3.0 5.0 V VCC(VCO) voltage controlled oscillator supply voltage 2.5 3.0 5.0 V VCCD digital supply voltage 2.5 3.0 5.0 V ICCA analog supply current operating; VCCA = 3 V 6.0 8.4 10.5 mA standby mode; VCCA = 3 V - 3 6 A ICC(VCO) voltage controlled oscillator supply current operating; VVCOTANK1 = VVCOTANK2 = 3 V 560 750 940 A standby mode; VVCOTANK1 = VVCOTANK2 = 3 V - 1 2 A ICCD digital supply current operating; VCCD = 3 V 2.1 3.0 3.9 mA bus enable line HIGH 30 56 80 A bus enable line LOW 11 19 26 A 76 - 108 MHz VCCA = VCC(VCO) = VCCD = 2.5 to 5 V -10 - +75 C fRF = 76 to 108 MHz; f = 22.5 kHz; fmod = 1 kHz; (S+N)/N = 26 dB; de-emphasis = 75 s; L = R; BAF = 300 Hz to 15 kHz - 2 3.5 V standby mode; VCCD = 3 V fFM(ant) FM input frequency Tamb ambient temperature FM overall system parameters; see Fig.5 VRF RF sensitivity input voltage S-200 LOW side 200 kHz selectivity f = -200 kHz; fRF = 76 to 108 MHz; note 1 32 36 - dB S+200 HIGH side 200 kHz selectivity f = +200 kHz; fRF = 76 to 108 MHz; note 1 39 43 - dB VAFL; VAFR left and right audio frequency VRF = 1 mV; L = R; f = 22.5 kHz; output voltage fmod = 1 kHz; de-emphasis = 75 s 60 75 90 mV (S+N)/N maximum signal plus noise-to-noise ratio VRF = 1 mV; L = R; f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; BAF = 300 Hz to 15 kHz 54 60 - dB cs(stereo) stereo channel separation VRF = 1 mV; R = L = 0 or R = 0 and L = 1 including 9% pilot; f = 75 kHz; fmod = 1 kHz; data byte 3 bit 3 = 0; data byte 4 bit 1 = 1 24 30 - dB THD total harmonic distortion VRF = 1 mV; L = R; f = 75 kHz; fmod = 1 kHz; - de-emphasis = 75 s 0.4 1 % Note 1. LOW side and HIGH side selectivity can be switched by changing the mixer from HIGH side to LOW side LO injection. 2003 Nov 06 4 This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... R1 33 nF 33 nF TIFC Vref MPXO TMUTE VAFL VAFR 23 22 21 20 19 18 17 Igain 25 GAIN STABILIZATION POWER SUPPLY AGND 26 22 nF VCCA 22 F 27 VCCA 4.7 RESONANCE AMPLIFIER DEMODULATOR LIMITER SOFT MUTE SDS I/Q-MIXER 1st FM FM antenna RFI1 28 27 pF RFGND 29 47 pF RFI2 30 33 k 22 nF 22 nF Iref 15 PHASEFIL AGC Ccomp(1) 14 XTAL2 TEA5768HL TAGC 31 4.7 nF TUNING SYSTEM MUX reference frequency divider output SOFTWARE PROGRAMMABLE PORT CRYSTAL OSCILLATOR Cpull(1) 13 XTAL1 32.768 kHz or 13 MHz 12 SWPORT2 10 k 11 SWPORT1 VCCA 10 k pilot mono VCO 1 I C-BUS 2 3 CPOUT VCOTANK1 10 nF 39 nF D1 10 BUSENABLE 2 VCOTANK2 D2 4 VCC(VCO) 9 BUSMODE 5 6 7 8 DGND VCCD DATA CLOCK VCCD MHC275 12 22 nF 10 k L3 L2 100 k The component list is given Chapter 14. (1) Ccomp and Cpull data depends on crystal specification. Fig.1 Block diagram. TEA5768HL VCC(VCO) Preliminary specification 22 nF 47 handbook, full pagewidth 5 programmable divider output LOOPSW 32 1 nF 16 PILFIL MPX DECODER IF CENTRE FREQUENCY ADJUST 100 pF L1 IF COUNTER LEVEL ADC 2 N1 Low-power FM stereo radio for handheld applications 24 47 nF BLOCK DIAGRAM 47 nF LIMDEC1 Philips Semiconductors 5 2003 Nov 06 47 nF LIMDEC2 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications 6 TEA5768HL PINNING SYMBOL PIN DESCRIPTION CPOUT 1 charge pump output of synthesizer PLL VCOTANK1 2 voltage controlled oscillator tuned circuit output 1 VCOTANK2 3 voltage controlled oscillator tuned circuit output 2 VCC(VCO) 4 voltage controlled oscillator supply voltage DGND 5 digital ground VCCD 6 digital supply voltage DATA 7 bus data line input/output CLOCK 8 bus clock line input BUSMODE 9 bus mode select input BUSENABLE 10 bus enable input SWPORT1 11 software programmable port 1 SWPORT2 12 software programmable port 2 XTAL1 13 crystal oscillator input 1 XTAL2 14 crystal oscillator input 2 PHASEFIL 15 phase detector loop filter PILFIL 16 pilot detector low-pass filter VAFR 17 right audio frequency output voltage VAFL 18 left audio frequency output voltage TMUTE 19 time constant for soft mute MPXO 20 FM demodulator MPX signal output Vref 21 reference voltage TIFC 22 time constant for IF centre adjust LIMDEC1 23 decoupling IF limiter 1 LIMDEC2 24 decoupling IF limiter 2 Igain 25 gain control current for IF filter AGND 26 analog ground VCCA 27 analog supply voltage RFI1 28 RF input 1 RFGND 29 RF ground RFI2 30 RF input 2 TAGC 31 time constant RF AGC LOOPSW 32 switch output of synthesizer PLL loop filter 2003 Nov 06 6 Philips Semiconductors Preliminary specification 25 Igain 26 AGND 27 VCCA 28 RFI1 29 RFGND TEA5768HL 30 RFI2 handbook, full pagewidth 31 TAGC 32 LOOPSW Low-power FM stereo radio for handheld applications CPOUT 1 24 LIMDEC2 VCOTANK1 2 23 LIMDEC1 VCOTANK2 3 22 TIFC VCC(VCO) 4 21 Vref TEA5768HL BUSMODE PILFIL 16 17 VAFR PHASEFIL 15 CLOCK 8 XTAL2 14 18 VAFL XTAL1 13 DATA 7 SWPORT2 12 19 TMUTE SWPORT1 11 VCCD 6 BUSENABLE 10 20 MPXO 9 DGND 5 MHC274 Fig.2 Pin configuration. 7 7.1 FUNCTIONAL DESCRIPTION The PLL synthesizer can be clocked externally with a 32.768 kHz, a 6.5 MHz or a 13 MHz signal via pin XTAL2. Low-noise RF amplifier The crystal oscillator generates the reference frequency for: The LNA input impedance together with the LC RF input circuit defines an FM band filter. The gain of the LNA is controlled by the RF AGC circuit. * The reference frequency divider for the synthesizer PLL * The timing for the IF counter 7.2 FM mixer * The free-running frequency adjustment of the stereo decoder VCO The FM quadrature mixer converts the FM RF (76 to 108 MHz) to an IF of 225 kHz. 7.3 * The centre frequency adjustment of the IF filters. VCO 7.5 The varactor tuned LC VCO provides the Local Oscillator (LO) signal for the FM quadrature mixer. The VCO frequency range is 150 to 217 MHz. 7.4 The PLL synthesizer tuning system is suitable to operate with a 32.768 kHz or a 13 MHz reference frequency generated by the crystal oscillator or applied to the IC from an external source. The synthesizer can also be clocked via pin XTAL2 at 6.5 MHz. The PLL tuning system can perform an autonomous search tuning function. Crystal oscillator The crystal oscillator can operate with a 32.768 kHz clock crystal or a 13 MHz crystal. The temperature drift of standard 32.768 kHz clock crystals limits the operational temperature range from -10 to +60 C. 2003 Nov 06 PLL tuning system 7.6 RF AGC The RF AGC prevents overloading and limits the amount of intermodulation products created by strong adjacent channels. 7 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications 7.7 TEA5768HL IF filter 8 I2C-BUS AND BUS-CONTROLLED FUNCTIONS Fully integrated IF filter. 8.1 7.8 Information about the I2C-bus can be found in the brochure "The I2C-bus and how to use it" (order number 9398 393 40011). FM demodulator The FM quadrature demodulator has an integrated resonator to perform the phase shift of the IF signal. 7.9 I2C-bus specification The standard I2C-bus specification is expanded by the following definitions. Level voltage generator and analog-to-digital converter IC address C0: 1100000. The FM IF analog level voltage is converted to 4 bits digital data and output via the I2C-bus. Structure of the I2C-bus logic: slave transceiver. 7.10 The maximum LOW-level input and the minimum HIGH-level input are specified to 0.2VCCD and 0.45VCCD respectively. The IF counter outputs a 7-bit count result via the 7.11 Subaddresses are not used. IF counter I2C-bus. Soft mute The pin BUSMODE must be connected to ground. The low-pass filtered level voltage drives the soft mute attenuator at low RF input levels. The soft mute function can be switched off via the I2C-bus. Note: The bus operates at a maximum clock frequency of 400 kHz. It is not allowed to connect the IC to a bus operating at a higher clock rate. 7.12 8.1.1 MPX decoder The PLL stereo decoder is adjustment-free. The stereo decoder can be switched to mono via the I2C-bus. 7.13 Data sequence: address, byte 1, byte 2, byte 3, byte 4 and byte 5 (the data transfer has to be in this order). The LSB = 0 of the address indicates a WRITE operation to the TEA5768HL. Signal dependent mono to stereo blend With a decreasing RF input level the MPX decoder blends from stereo to mono to limit the output noise. The continuous mono to stereo blend can also be programmed via the I2C-bus to an RF level depending switched mono to stereo transition. Stereo Noise Cancelling (SNC) can be switched off via the I2C-bus. 7.14 DATA TRANSFER Bit 7 of each byte is considered as the MSB and has to be transferred as the first bit of the byte. The data becomes valid bitwise at the appropriate falling edge of the clock. A STOP condition after any byte can shorten transmission times. When writing to the transceiver by using the STOP condition before completion of the whole transfer: Signal dependent AF response The audio bandwidth will be reduced with a decreasing RF input level. The function can be switched off via the I2C-bus. * The remaining bytes will contain the old information 7.15 The IC can be switched into a low current standby mode with the standby bit; the bus is then still active. The standby current can be reduced by deactivating the bus interface (pin BUSENABLE LOW). If the bus interface is deactivated (pin BUSENABLE LOW) without the standby mode being programmed, the IC maintains normal operation, but is isolated from the bus lines. * If the transfer of a byte is not completed, the new bits will be used, but a new tuning cycle will not be started. Software programmable ports Two software programmable ports (open-collector) can be addressed via the I2C-bus. The port 1 (pin SWPORT1) function can be changed with write data byte 4 bit 0 (see Table 13). Pin SWPORT1 is then output for the ready flag of read byte 1. 2003 Nov 06 8 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL The software programmable output (SWPORT1) can be programmed to operate as a tuning indicator output. As long as the IC has not completed a tuning action, pin SWPORT1 remains LOW. The pin becomes HIGH, when a preset or search tuning is completed or when a band limit is reached. 8.1.2 POWER-ON RESET At Power-on reset the mute is set, all other bits are set to LOW. To initialize the IC all bytes have to be transferred. The reference frequency divider of the synthesizer PLL is changed when the MSB in byte 5 is set to logic 1. The tuning system can then be clocked via pin XTAL2 at 6.5 MHz. I2C-bus protocol 8.2 Table 1 Write mode S(1) address (write) A(2) address (read) A(2) data byte(s) A(2) P(3) Notes 1. S = START condition. 2. A = acknowledge. 3. P = STOP condition. Table 2 Read mode S(1) data byte 1 Notes 1. S = START condition. 2. A = acknowledge. Table 3 IC address byte IC ADDRESS 1 1 0 0 0 Note 1. Read or write mode: a) 0 = write operation to the TEA5768HL b) 1 = read operation from the TEA5768HL. 2003 Nov 06 MODE 9 0 0 R/W(1) Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications 8.3 TEA5768HL Writing data Table 4 Write mode DATA BYTE 1 Table 5 DATA BYTE 2 DATA BYTE 3 DATA BYTE 4 DATA BYTE 5 Format of 1st data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) MUTE SM PLL13 PLL12 PLL11 PLL10 PLL9 PLL8 Table 6 Description of 1st data byte bits BIT SYMBOL 7 MUTE 6 SM 5 to 0 PLL[13:8] Table 7 DESCRIPTION if MUTE = 1 then L and R audio are muted; if MUTE = 0 then L and R audio are not muted Search Mode: if SM = 1 then in search mode; if SM = 0 then not in search mode setting of synthesizer programmable counter for search or preset Format of 2nd data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) PLL7 PLL6 PLL5 PLL4 PLL3 PLL2 PLL1 PLL0 Table 8 Description of 2nd data byte bits BIT SYMBOL 7 to 0 PLL[7:0] Table 9 DESCRIPTION setting of synthesizer programmable counter for search or preset Format of 3rd data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) SUD SSL1 SSL0 HLSI MS MR ML SWP1 Table 10 Description of 3rd data byte bits BIT SYMBOL 7 SUD 6 and 5 SSL[1:0] 4 HLSI 3 MS Mono to Stereo: if MS = 1 then forced mono; if MS = 0 then stereo ON 2 MR Mute Right: if MR = 1 then the right audio channel is muted and forced mono; if MR = 0 then the right audio channel is not muted 1 ML Mute Left: if ML = 1 then the left audio channel is muted and forced mono; if ML = 0 then the left audio channel is not muted 0 SWP1 Software programmable port 1: if SWP1 = 1 then port 1 is HIGH; if SWP1 = 0 then port 1 is LOW 2003 Nov 06 DESCRIPTION Search Up/Down: if SUD = 1 then search up; if SUD = 0 then search down Search Stop Level: see Table 11 HIGH/LOW Side Injection: if HLSI = 1 then HIGH side LO injection; if HLSI = 0 then LOW side LO injection 10 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL Table 11 Search stop level setting SSL1 SSL0 SEARCH STOP LEVEL 0 0 not allowed in search mode 0 1 low; level ADC output = 5 1 0 mid; level ADC output = 7 1 1 high; level ADC output = 10 Table 12 Format of 4th data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) SWP2 STBY BL XTAL SMUTE HCC SNC SI Table 13 Description of 4th data byte bits BIT SYMBOL DESCRIPTION 7 SWP2 Software programmable port 2: if SWP2 = 1 then port 2 is HIGH; if SWP2 = 0 then port 2 is LOW 6 STBY Standby: if STBY = 1 then in standby mode; if STBY = 0 then not in standby mode Band Limits: if BL = 1 then Japanese FM band; if BL = 0 then US/Europe FM band 5 BL 4 XTAL 3 SMUTE 2 HCC High Cut Control: if HCC = 1 then high cut control is ON; if HCC = 0 then high cut control is OFF 1 SNC Stereo Noise Cancelling: if SNC = 1 then stereo noise cancelling is ON; if SNC = 0 then stereo noise cancelling is OFF 0 SI if XTAL = 1 then fxtal = 32.768 kHz; if XTAL = 0 then fxtal = 13 MHz Soft MUTE: if SMUTE = 1 then soft mute is ON; if SMUTE = 0 then soft mute is OFF Search Indicator: if SI = 1 then pin SWPORT1 is output for the ready flag; if SI = 0 then pin SWPORT1 is software programmable port 1 Table 14 Format of 5th data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) PLLREF DTC - - - - - - Table 15 Description of 5th data byte bits BIT SYMBOL 7 PLLREF if PLLREF = 1 then the 6.5 MHz reference frequency for the PLL is enabled; if PLLREF = 0 then the 6.5 MHz reference frequency for the PLL is disabled 6 DTC if DTC = 1 then the de-emphasis time constant is 75 s; if DTC = 0 then the de-emphasis time constant is 50 s 5 to 0 - 2003 Nov 06 DESCRIPTION not used; position is don't care 11 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications 8.4 TEA5768HL Reading data Table 16 Read mode DATA BYTE 1 DATA BYTE 2 DATA BYTE 3 DATA BYTE 4 DATA BYTE 5 Table 17 Format of 1st data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) RF BLF PLL13 PLL12 PLL11 PLL10 PLL9 PLL8 Table 18 Description of 1st data byte bits BIT SYMBOL DESCRIPTION 7 RF Ready Flag: if RF = 1 then a station has been found or the band limit has been reached; if RF = 0 then no station has been found 6 BLF Band Limit Flag: if BLF = 1 then the band limit has been reached; if BLF = 0 then the band limit has not been reached 5 to 0 PLL[13:8] setting of synthesizer programmable counter after search or preset Table 19 Format of 2nd data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) PLL7 PLL6 PLL5 PLL4 PLL3 PLL2 PLL1 PLL0 Table 20 Description of 2nd data byte bits BIT SYMBOL 7 to 0 PLL[7:0] DESCRIPTION setting of synthesizer programmable counter after search or preset Table 21 Format of 3rd data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) STEREO IF6 IF5 IF4 IF3 IF2 IF1 IF0 Table 22 Description of 3rd data byte bits BIT SYMBOL 7 STEREO Stereo indication: if STEREO = 1 then stereo reception; if STEREO = 0 then mono reception 6 to 0 PLL[13:8] IF counter result 2003 Nov 06 DESCRIPTION 12 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL Table 23 Format of 4th data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) LEV3 LEV2 LEV1 LEV0 CI3 CI2 CI1 0 Table 24 Description of 4th data byte bits BIT SYMBOL 7 to 4 LEV[3:0] 3 to 1 CI[3:1] 0 - DESCRIPTION level ADC output Chip Identification: these bits have to be set to logic 0 this bit is internally set to logic 0 Table 25 Format of 5th data byte BIT 7 (MSB) BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 (LSB) 0 0 0 0 0 0 0 0 Table 26 Description of 5th data byte bits BIT SYMBOL 7 to 0 - 8.5 DESCRIPTION reserved for future extensions; these bits are internally set to logic 0 Bus timing Table 27 Digital levels and timing SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT Digital inputs VIH HIGH-level input voltage 0.45VCCD - V VIL LOW-level input voltage - 0.2VCCD V 500 - A - 450 mV Digital outputs Isink(L) LOW-level sink current VOL LOW-level output voltage IOL = 500 A Timing (I2C-bus enabled) fclk clock input frequency - 400 kHz tHIGH clock HIGH time 1 - s tLOW clock LOW time 1 - s 2003 Nov 06 13 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 9 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VVCOTANK1 VCO tuned circuit output voltage 1 -0.3 +8 V VVCOTANK2 VCO tuned circuit output voltage 2 -0.3 +8 V VCCD digital supply voltage -0.3 +5 V VCCA analog supply voltage -0.3 +8 V Tstg storage temperature -55 +150 C Tamb ambient temperature -10 +75 C Ves electrostatic handling voltage note 1 -200 +200 V note 2 -2000 +2000 V note 1 -150 +200 V note 2 -2000 +2000 V for all pins except pin DATA for pin DATA Notes 1. Machine model (R = 0 , C = 200 pF). 2. Human body model (R = 1.5 k, C = 100 pF). 10 THERMAL CHARACTERISTICS SYMBOL Rth(j-a) 2003 Nov 06 PARAMETER CONDITIONS thermal resistance from junction to ambient in free air 14 VALUE UNIT 80 K/W Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 11 DC CHARACTERISTICS VCCA = VVCOTANK1 = VVCOTANK2 = VCCD = 2.7 V; Tamb = 25 C; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Supply voltages; note 1 VCCA analog supply voltage 2.5 3.0 5.0 V VCC(VCO) voltage controlled oscillator supply voltage 2.5 3.0 5.0 V VCCD digital supply voltage 2.5 3.0 5.0 V VCCA = 3 V 6.0 8.4 10.5 mA VCCA = 5 V 6.2 8.6 10.7 mA VCCA = 3 V - 3 6 A VCCA = 5 V - 3.2 6.2 A VVCOTANK1 = VVCOTANK2 = 3 V 560 750 940 A VVCOTANK1 = VVCOTANK2 = 5 V 570 760 950 A VVCOTANK1 = VVCOTANK2 = 3 V - 1 2 A VVCOTANK1 = VVCOTANK2 = 5 V - 1.2 2.2 A Supply currents ICCA analog supply current operating standby mode ICC(VCO) voltage controlled oscillator supply current operating standby mode ICCD digital supply current operating VCCD = 3 V 2.1 3.0 3.9 mA VCCD = 5 V 2.25 3.15 4.05 mA bus enable line HIGH 30 56 80 A bus enable line LOW 11 19 26 A bus enable line HIGH 50 78 105 A bus enable line LOW 20 33 45 A standby mode; VCCD = 3 V standby mode; VCCD = 5 V 2003 Nov 06 15 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications SYMBOL PARAMETER TEA5768HL CONDITIONS MIN. TYP. MAX. UNIT DC operating points VCPOUT VXTAL1 VXTAL2 0.1 - VCC(VCO) - 0.1 V data byte 4 bit 4 = 1 1.64 1.72 1.8 V data byte 4 bit 4 = 0 1.68 1.75 1.82 V data byte 4 bit 4 = 1 1.64 1.72 1.8 V data byte 4 bit 4 = 0 1.68 1.75 1.82 V 0.4 1.2 VCCA - 0.4 V unloaded DC voltage VPHASEFIL 0.65 0.9 1.3 V VVAFL fRF = 98 MHz; VRF = 1 mV 720 850 940 mV VVAFR fRF = 98 MHz; VRF = 1 mV 720 850 940 mV VTMUTE VRF = 0 V 1.5 1.65 1.8 V VMPXO fRF = 98 MHz; VRF = 1 mV 680 815 950 mV VVref 1.45 1.55 1.65 V VTIFC 1.34 1.44 1.54 V VLIMDEC1 1.86 1.98 2.1 V VLIMDEC2 1.86 1.98 2.1 V VIgain 480 530 580 mV VRFI1 0.93 1.03 1.13 V VRFI2 0.93 1.03 1.13 V 1 1.57 2 V VPILFIL VTAGC VRF = 0 V Note 1. VCCA, VCC(VCO) and VCCD must not differ more than 200 mV. 2003 Nov 06 16 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 12 AC CHARACTERISTICS VCCA = VVCOTANK1 = VVCOTANK2 = VCCD = 2.7 V; Tamb = 25 C; measured in the circuit of Fig.5; all AC values are given in RMS; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Voltage controlled oscillator fosc 150 - 217 MHz 140 - 350 mV data byte 4 bit 4 = 0 2 3 4 k data byte 4 bit 4 = 1 230 330 430 k data byte 4 bit 4 = 0 3.9 5.6 7.3 pF data byte 4 bit 4 = 1 5 6 7 pF oscillator frequency Crystal oscillator CIRCUIT INPUT: PIN XTAL2 Vi(osc) oscillator input voltage oscillator externally clocked Ri input resistance oscillator externally clocked Ci input capacitance oscillator externally clocked CRYSTAL: 32.768 kHz fr series resonance frequency data byte 4 bit 4 = 1 - f/fr frequency deviation -20 x C0 shunt capacitance - RS series resistance - fr/fr(25 C) temperature drift -10 C < Tamb < +60 C -50 x 32.768 - 10-6 10-6 - +20 x - 3.5 - 80 - +50 x 13 - kHz 10-6 pF k 10-6 CRYSTAL: 13 MHz fr series resonance frequency data byte 4 bit 4 = 0 - 10-6 MHz 10-6 f/fr frequency deviation -30 x - +30 x C0 shunt capacitance - - 4.5 pF Cmot motional capacitance 1.5 - 3.0 fF RS series resistance - - 100 fr/fr(25 C) temperature drift -40 C < Tamb < +85 C -30 x 10-6 - +30 x 10-6 data byte 1 = XX111111; data byte 2 = 11111110 - - 8191 data byte 1 = XX010000; data byte 2 = 00000000 2048 - - - 1 - data byte 4 bit 4 = 0 - 260 - data byte 5 bit 7 = 1; data byte 4 bit 4 = 0 - 130 - data byte 4 bit 4 = 1 - 1 - Synthesizer PROGRAMMABLE DIVIDER; note 1 Nprog Nstep programmable divider ratio programmable divider step size REFERENCE FREQUENCY DIVIDER Nref 2003 Nov 06 crystal oscillator divider ratio 17 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications SYMBOL PARAMETER TEA5768HL CONDITIONS MIN. TYP. MAX. UNIT CHARGE PUMP: PIN CPOUT Isink charge pump peak sink current 0.2 V < VCPOUT < VVCOTANK2 - 0.2 V; fVCO > fref x Nprog - 0.5 - A Isource charge pump peak source current 0.2 V < VCPOUT < VVCOTANK2 - 0.2 V; fVCO < fref x Nprog - -0.5 - A IF counter VRF RF input voltage for correct IF count - 12 18 V NIF IF counter length - 7 - bit Nprecount IF counter prescaler ratio - Tcount(IF) IF counter period REScount(IF) IF counter resolution IFcount IF counter result for search tuning stop - 64 fxtal = 32.768 kHz - 15.625 - ms fxtal = 13 MHz - 15.754 - ms fxtal = 32.768 kHz - 4.096 - kHz fxtal = 13 MHz - 4.0625 - kHz fxtal = 32.768 kHz 31 - 3E HEX fxtal = 13 MHz 32 - 3D HEX 10 - - M Pins DATA, CLOCK, BUSMODE and BUSENABLE Ri input resistance Software programmable ports PIN SWPORT1 Isink(max) maximum sink current data byte 4 bit 0 = 0; data byte 5 bit 0 = 0; VSWPORT1 < 0.5 V 500 - - A Ileak(max) maximum leakage current data byte 4 bit 0 = 1; VSWPORT1 < 5 V -1 - +1 A PIN SWPORT2 Isink(max) maximum sink current data byte 5 bit 7 = 0; VSWPORT1 < 0.5 V 500 - - A Ileak(max) maximum leakage current data byte 5 bit 1 = 1; VSWPORT1 < 5 V -1 - +1 A FM signal channel FM RF INPUT Ri input resistance at pins RFI1 and RFI2 to RFGND 75 100 125 Ci input capacitance at pins RFI1 and RFI2 to RFGND) 2.5 4 6 pF 2003 Nov 06 18 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications SYMBOL PARAMETER TEA5768HL CONDITIONS MIN. TYP. MAX. UNIT VRF RF sensitivity input voltage fRF = 76 to 108 MHz; f = 22.5 kHz; fmod = 1 kHz; (S+N)/N = 26 dB; de-emphasis = 75 s; BAF = 300 Hz to 15 kHz - 2 3.5 V IP3in in-band 3rd-order intercept point related to VRFI1-RFI2 (peak value) f1 = 200 kHz; f2 = 400 kHz; ftune = 76 to 108 MHz 81 84 - dBV IP3out out-band 3rd-order intercept point related to VRFI1-RFI2 (peak value) f1 = 4 MHz; f2 = 8 Hz; ftune = 76 to 108 MHz 82 85 - dBV RF input voltage for start of AGC fRF1 = 93 MHz; fRF2 = 98 MHz; VRF2 = 50 dBV; 66 72 78 dBV RF AGC VRF1 V TMUTE 14 mV - ; note 2 ----------------------- < ------------------3 dBV V RF1 IF filter fIF IF filter centre frequency 215 225 235 kHz BIF IF filter bandwidth 85 94 102 kHz S+200 HIGH side 200 kHz selectivity f = +200 kHz; ftune = 76 to 108 MHz; note 3 39 43 - dB S-200 LOW side 200 kHz selectivity f = -200 kHz; ftune = 76 to 108 MHz; note 3 32 36 - dB S+100 HIGH side 100 kHz selectivity f = +100 kHz; ftune = 76 to 108 MHz; note 3 8 12 - dB S-100 LOW side 100 kHz selectivity f = -100 kHz; ftune = 76 to 108 MHz; note 3 8 12 - dB IR image rejection ftune = 76 to 108 MHz; VRF = 50 dBV 24 30 - dB read mode data byte 4 bit 4 = 1 2 3 5 V 2 3 5 dB VRF = 0 V 1.55 1.65 1.80 V VRF = 3 V 1.60 1.70 1.85 V VRF = 10 to 500 V 150 165 180 mV --------------20 dB 280 400 520 k FM IF level detector and mute voltage VRF RF input voltage for start of level ADC Vstep level ADC step size PIN TMUTE Vlevel level output DC voltage Vlevel(slope) slope of level voltage Ro output resistance 2003 Nov 06 19 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications SYMBOL PARAMETER TEA5768HL CONDITIONS MIN. TYP. MAX. UNIT FM demodulator: pin MPXO VMPXO demodulator output voltage VRF = 1 mV; L = R; f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; BAF = 300 Hz to 15 kHz 60 75 90 mV (S+N)/N maximum signal plus noise-to-noise ratio VRF = 1 mV; L = R; f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; BAF = 300 Hz to 15 kHz 54 60 - dB THD total harmonic distortion VRF = 1 mV; L = R; f = 75 kHz; - fmod = 1 kHz; de-emphasis = 75 s 0.5 1.5 % AM AM suppression VRF = 300 V; L = R; f = 22.5 kHz; fmod = 1 kHz; m = 0.3; de-emphasis = 75 s; BAF = 300 Hz to 15 kHz 40 - - dB Ro demodulator output resistance - - 500 Isink demodulator output sink current - - 30 A Soft mute VRF RF input voltage for soft mute start mute = 3 dB; data byte 4 bit 3 = 1 3 5 10 V mute mute attenuation VRF = 1 V; L = R; f = 22.5 kHz; fmod = 1 kHz de-emphasis = 75 s; BAF = 300 Hz to 15 kHz; data byte 4 bit 3 = 1 10 20 30 dB VRF = 1 mV; L = R; f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s 60 75 90 mV MPX decoder VAFL; VAFR left and right audio frequency output voltage RAFL; RAFR left and right audio frequency output resistance - - 50 Isink(AFL); Isink(AFR) left and right audio frequency output sink current 170 - - A 4 - - dB VMPXIN(max) input overdrive margin THD < 3% VAFL/VAFR left and right audio frequency output voltage difference VRF = 1 mV; L = R; f = 75 kHz; -1 fmod = 1 kHz; de-emphasis = 75 s - +1 dB cs(stereo) stereo channel separation VRF = 1 mV; R = L = 0 or R = 0 and L = 1 including 9% pilot; f = 75 kHz; fmod = 1 kHz; data byte 3 bit 3 = 0; data byte 4 bit 1 = 1 30 - dB 2003 Nov 06 20 24 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications SYMBOL PARAMETER TEA5768HL CONDITIONS MIN. UNIT - dB 0.4 1 % 40 50 - dB bit 7 = 1 - 3.6 5.8 kHz bit 7 = 0 1 3 - kHz VRF = 1 mV 2 - - dB data byte 5 bit 2 = 0 38 50 62 s data byte 5 bit 2 = 1 57 75 93 s data byte 5 bit 2 = 0 114 150 186 s data byte 5 bit 2 = 1 171 225 279 s VRF = 45 V; R = L = 0 or R = 0 4 and L = 1 including 9% pilot; f = 75 kHz; fmod = 1 kHz; data byte 3 bit 3 = 0; data byte 4 bit 1 = 1 10 16 dB - - dB - 1 dB maximum signal plus noise-to-noise ratio VRF = 1 mV; L = R; f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; BAF = 300 Hz to 15 kHz THD total harmonic distortion VRF = 1 mV; L = R; f = 75 kHz; - fmod = 1 kHz; de-emphasis = 75 s pilot pilot suppression measured related to f = 75 kHz; at pins VAFL and VAFR fmod = 1 kHz; de-emphasis = 75 s fpilot stereo pilot frequency deviation pilot switch hysteresis MAX. 60 (S+N)/N f pilot1 ---------------f pilot2 TYP. 54 VRF = 1 mV; read mode; data byte 3 HIGH CUT CONTROL TCde-em de-emphasis time constant VRF = 1 mV VRF = 1 V MONO TO STEREO BLEND CONTROL cs(stereo) stereo channel separation MONO TO STEREO SWITCHED cs(stereo) stereo channel separation switching from mono to stereo with increasing RF input level VRF = 1 V; R = L = 0 or R = 0 and L = 1 including 9% pilot; f = 75 kHz; fmod = 1 kHz; data byte 3 bit 3 = 0; data byte 4 bit 1 = 0 cs(stereo) stereo channel separation switching from stereo to mono with decreasing RF input level VRF = 20 V; R = L = 0 or R = 0 - and L = 1 including 9% pilot; f = 75 kHz; fmod = 1 kHz; data byte 3 bit 3 = 0; data byte 4 bit 1 = 0 2003 Nov 06 21 24 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications SYMBOL PARAMETER TEA5768HL CONDITIONS MIN. TYP. MAX. UNIT BUS-DRIVEN MUTE FUNCTIONS Tuning mute mute VAFL and VAFR muting depth data byte 1 bit 7 = 1 - - -60 dB mute(L) VAFL muting depth data byte 3 bit 1 = 1; fAF = 1 kHz; Rload(L) < 30 k - - -80 dB mute(R) VAFR muting depth data byte 3 bit 2 = 1; fAF = 1 kHz; Rload(R) < 30 k - - -80 dB Notes 1. Calculation of this 14-bit word can be done as follows: 4 x ( f RF - f IF ) 4 x ( f RF + f IF ) formula for HIGH side injection: N = --------------------------------- ; formula for LOW side injection: N = ---------------------------------f ref f ref where: N = decimal value of PLL word fRF = the wanted tuning frequency [Hz] fIF = the intermediate frequency [Hz] = 225 kHz fref = the reference frequency [Hz] = 32.768 kHz for the 32.768 kHz crystal; fref = 50 kHz for the 13 MHz crystal or when externally clocked with 6.5 MHz. 6 3 4 x ( 100 x10 + 225 x10 ) Example for receiving a channel at 100 MHz with HIGH side injection: N = ------------------------------------------------------------------ = 12234 . 32768 The PLL word becomes 2FCAH. 2. VRF in Fig.5 is replaced by VRF1 + VRF2. The radio is tuned to 98 MHz (HIGH side injection). 3. LOW side and HIGH side selectivity can be switched by changing the mixer from HIGH side to LOW side LO injection. 2003 Nov 06 22 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL MHC247 10 THD (%) 4.0 handbook, full pagewidth VAFL, VAFR (dB) 0 -10 (1) (2) (3) 3.5 -20 3.0 -30 2.5 -40 (4) 2.0 (5) -50 1.5 -60 1.0 -70 -80 10-3 (1) (2) (3) (4) (5) (6) 0.5 (6) 10-2 10-1 1 Mono signal; soft mute on. Left channel with modulation left; SNC on. Right channel with modulation left; SNC on. Noise in mono mode; soft mute on. Noise in stereo mode; SNC on. Total harmonic distortion; f = 75 kHz; L = R; fmod = 1 kHz. Fig.3 FM characteristics 1. 2003 Nov 06 23 10 102 VRF (mV) 0 103 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL MHC309 10 VTMUTE (V) 2.2 handbook, full pagewidth VAFL, VAFR (dB) 0 (1) -10 -20 2.1 2.0 (2) -30 1.9 -40 1.8 -50 (3) 1.7 -60 1.6 -70 1.5 -80 10-3 10-2 10-1 1 (1) Mono signal; no soft mute. (2) Noise in mono mode; no soft mute. (3) Level voltage; VCCA = 2.7 V. Fig.4 FM characteristics 2. 2003 Nov 06 24 10 102 VRF (mV) 1.4 103 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 13 INTERNAL PIN CONFIGURATION PIN 1 SYMBOL EQUIVALENT CIRCUIT CPOUT 270 1 2 VCOTANK1 3 VCOTANK2 MHC251 2 3 120 120 MHC252 4 VCC(VCO) 5 DGND 6 VCCD 7 DATA 7 5 8 MHC253 CLOCK 270 8 2003 Nov 06 25 5 MHC254 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications PIN 9 TEA5768HL SYMBOL EQUIVALENT CIRCUIT BUSMODE 270 10 9 5 10 5 MHC255 BUSENABLE 150 11 SWPORT1 150 5 12 SWPORT2 13 XTAL1 14 XTAL2 11 MHC257 150 5 MHC256 12 MHC258 13 14 MHC259 15 PHASEFIL 15 26 2003 Nov 06 26 MHC260 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications PIN 16 TEA5768HL SYMBOL EQUIVALENT CIRCUIT PILFIL 270 26 17 16 MHC261 VAFR 10 17 26 18 MHC262 VAFL 10 18 26 19 TMUTE MHC263 19 1 k 26 20 MHC264 MPXO 150 26 2003 Nov 06 27 20 MHC265 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications PIN 21 TEA5768HL SYMBOL EQUIVALENT CIRCUIT Vref 21 26 MHC266 22 TIFC 40 k 22 MHC267 23 LIMDEC1 270 23 MHC268 24 LIMDEC2 270 24 MHC269 25 Igain 25 MHC270 26 AGND 27 VCCA 2003 Nov 06 28 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications PIN TEA5768HL SYMBOL 28 RFI1 29 RFGND 30 RFI2 EQUIVALENT CIRCUIT 28 30 MHC271 29 31 TAGC 31 29 32 LOOPSW MHC272 4 32 MHC273 14 APPLICATION INFORMATION Table 28 Component list for Figs 1 and 5 COMPONENT PARAMETER VALUE TOLERANCE R1 resistor with low temperature coefficient 18 k 1% - TYPE RC12G Philips BB202 Philips D1 and D2 varicap for VCO tuning - L1 RF band filter coil 120 nH 2% Qmin = 40 L2 and L3 VCO coil 33 nH 2% Qmin = 40 NX4025GA XTAL13 13 MHz crystal - - Cpull pulling capacitor for NX4025GA 10 pF - XTAL32.768 32.768 kHz crystal - - 2003 Nov 06 29 MANUFACTURER This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 24 R1 47 nF 33 nF 33 nF LIMDEC1 TIFC Vref MPXO TMUTE VAFL VAFR 23 22 21 20 19 18 17 Igain 25 GAIN STABILIZATION POWER SUPPLY AGND 26 22 nF VCCA 22 F 27 VCCA 4.7 RESONANCE AMPLIFIER DEMODULATOR LIMITER SOFT MUTE SDS I/Q-MIXER 1st FM RFI1 28 L1 27 pF RFGND 29 47 pF RFI2 30 33 k 22 nF 22 nF Iref 15 PHASEFIL AGC TAGC 31 4.7 nF TUNING SYSTEM MUX reference frequency divider output SOFTWARE PROGRAMMABLE PORT CRYSTAL OSCILLATOR Cpull(1) 13 XTAL1 32.768 kHz or 13 MHz 12 SWPORT2 10 k 11 SWPORT1 VCCA 10 k pilot mono VCO 1 I C-BUS 2 3 CPOUT VCOTANK1 10 nF 39 nF D1 10 BUSENABLE 2 VCOTANK2 D2 4 VCC(VCO) 9 BUSMODE 5 6 7 8 DGND VCCD DATA CLOCK VCCD MHC276 12 22 nF 10 k L3 100 k 22 nF (1) Ccomp and Cpull data depends on crystal specification. Fig.5 Test circuit. TEA5768HL VCC(VCO) Preliminary specification 47 L2 handbook, full pagewidth 30 programmable divider output LOOPSW 32 Ccomp(1) 14 XTAL2 TEA5768HL VRF 1 nF 16 PILFIL MPX DECODER IF CENTRE FREQUENCY ADJUST 100 pF 40 IF COUNTER LEVEL ADC 2 N1 Philips Semiconductors 47 nF Low-power FM stereo radio for handheld applications 2003 Nov 06 47 nF LIMDEC2 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 15 PACKAGE OUTLINE LQFP32: plastic low profile quad flat package; 32 leads; body 7 x 7 x 1.4 mm SOT358-1 c y X 24 A 17 16 25 ZE e E HE A A2 A 1 (A 3) wM bp Lp pin 1 index L 32 9 detail X 8 1 e ZD v M A wM bp D B HD v M B 0 2.5 5 mm scale DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (1) e HD HE L Lp v w y mm 1.6 0.20 0.05 1.45 1.35 0.25 0.4 0.3 0.18 0.12 7.1 6.9 7.1 6.9 0.8 9.15 8.85 9.15 8.85 1 0.75 0.45 0.2 0.25 0.1 Z D (1) Z E (1) 0.9 0.5 0.9 0.5 o 7 0o Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT358 -1 136E03 MS-026 2003 Nov 06 JEITA EUROPEAN PROJECTION ISSUE DATE 00-01-19 03-02-25 31 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL To overcome these problems the double-wave soldering method was specifically developed. 16 SOLDERING 16.1 Introduction to soldering surface mount packages If wave soldering is used the following conditions must be observed for optimal results: This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. * For packages with leads on two sides and a pitch (e): There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 16.2 - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. Reflow soldering The footprint must incorporate solder thieves at the downstream end. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Driven by legislation and environmental forces the worldwide use of lead-free solder pastes is increasing. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical reflow peak temperatures range from 215 to 270 C depending on solder paste material. The top-surface temperature of the packages should preferably be kept: Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 C or 265 C, depending on solder material applied, SnPb or Pb-free respectively. * below 220 C (SnPb process) or below 245 C (Pb-free process) A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. - for all BGA and SSOP-T packages 16.4 - for packages with a thickness 2.5 mm Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. - for packages with a thickness < 2.5 mm and a volume 350 mm3 so called thick/large packages. * below 235 C (SnPb process) or below 260 C (Pb-free process) for packages with a thickness < 2.5 mm and a volume < 350 mm3 so called small/thin packages. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C. Moisture sensitivity precautions, as indicated on packing, must be respected at all times. 16.3 Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. 2003 Nov 06 Manual soldering 32 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications 16.5 TEA5768HL Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE(1) WAVE BGA, LBGA, LFBGA, SQFP, SSOP-T(3), TFBGA, VFBGA not suitable suitable(4) DHVQFN, HBCC, HBGA, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, HVQFN, HVSON, SMS not PLCC(5), SO, SOJ suitable REFLOW(2) suitable suitable suitable not recommended(5)(6) suitable SSOP, TSSOP, VSO, VSSOP not recommended(7) suitable PMFP(8) not suitable LQFP, QFP, TQFP not suitable Notes 1. For more detailed information on the BGA packages refer to the "(LF)BGA Application Note" (AN01026); order a copy from your Philips Semiconductors sales office. 2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 3. These transparent plastic packages are extremely sensitive to reflow soldering conditions and must on no account be processed through more than one soldering cycle or subjected to infrared reflow soldering with peak temperature exceeding 217 C 10 C measured in the atmosphere of the reflow oven. The package body peak temperature must be kept as low as possible. 4. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. 5. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 6. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 7. Wave soldering is suitable for SSOP, TSSOP, VSO and VSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 8. Hot bar or manual soldering is suitable for PMFP packages. 2003 Nov 06 33 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 17 DATA SHEET STATUS LEVEL DATA SHEET STATUS(1) PRODUCT STATUS(2)(3) Development DEFINITION I Objective data II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Production This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 18 DEFINITIONS 19 DISCLAIMERS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Right to make changes Philips Semiconductors reserves the right to make changes in the products including circuits, standard cells, and/or software described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 2003 Nov 06 34 Philips Semiconductors Preliminary specification Low-power FM stereo radio for handheld applications TEA5768HL 20 PURCHASE OF PHILIPS I2C COMPONENTS Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011. 2003 Nov 06 35 Philips Semiconductors - a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. SCA75 (c) Koninklijke Philips Electronics N.V. 2003 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands R30/02/pp36 Date of release: 2003 Nov 06 Document order number: 9397 750 12072