C4D20120D VRRM Silicon Carbide Schottky Diode 1200 V IF (TC=135C) = 33 A** Z-Rec Rectifier (R) Qc Features * * * * * = = 104 nC** Package 1.2-KVolt Schottky Rectifier Zero Reverse Recovery Current High-Frequency Operation Temperature-Independent Switching Behavior Positive Temperature Coefficient on VF Benefits * * * * * TO-247-3 Replace Bipolar with Unipolar Rectifiers Essentially No Switching Losses Higher Efficiency Reduction of Heat Sink Requirements Parallel Devices Without Thermal Runaway Applications * * * Switch Mode Power Supplies Power Factor Correction Motor Drives Part Number Package Marking C4D20120D TO-247-3 C4D20120 Maximum Ratings (TC=25C unless otherwise specified) Symbol Parameter Repetitive Peak Reverse Voltage 1200 V VRSM Surge Peak Reverse Voltage 1300 V VDC DC Blocking Voltage 1200 V 34/68 16.5/33 10/20 A TC=25C TC=135C TC=157C Continuous Forward Current (Per Leg/Device) IFRM Repetitive Peak Forward Surge Current 47* 31.5* A TC=25C, tP=10 ms, Half Sine Pulse TC-110C, tP=10 ms, Half Sine Pulse IFSM Non-Repetitive Peak Forward Surge Current 71* 59.5* A TC=25C, tP=10 ms, Half Sine Pulse TC=110C, tP=10 ms, Half Sine Pulse IF,Max Non-Repetitive Peak Forward Current 750* 620* A TC=25C, tP=10 ms, Pulse TC=110C, tP=10 ms, Pulse 176/352 76/152 W TC=25C TC=110C Ptot Power Dissipation(Per Leg/Device) TJ Operating Junction Range -55 to +175 C Tstg Storage Temperature Range -55 to +135 C 1 8.8 Nm lbf-in TO-247 Mounting Torque 1 Test Conditions VRRM IF * Value Per Leg, ** Per Device C4D20120D Rev. D M3 Screw 6-32 Screw Note Electrical Characteristics (Per Leg) Symbol Parameter Typ. Max. Unit Test Conditions Note VF Forward Voltage 1.5 2.2 1.8 3 V IF = 10 A TJ=25C IF = 10 A TJ=175C IR Reverse Current 30 55 250 350 A VR = 1200 V TJ=25C VR = 1200 V TJ=175C QC Total Capacitive Charge 52 nC VR = 800 V, IF = 10A di/dt = 200 A/s TJ = 25C C Total Capacitance 754 45 38 pF VR = 0 V, TJ = 25C, f = 1 MHz VR = 400 V, TJ = 25C, f = 1 MHz VR = 800 V, TJ = 25C, f = 1 MHz Note: 1. This is a majority carrier diode, so there is no reverse recovery charge. Thermal Characteristics Symbol Parameter Typ. RJC Thermal Resistance from Junction to Case 0.85* 0.43** * Per Leg, ** Max. Unit Test Conditions Note C/W Per Device Typical Performance (Per Leg) 700 0.0007 20 20 600 0.0006 12 12 10 10 88 66 44 500 0.0005 400 0.0004 0.0003 300 R 14 14 Current (A) IR Reverse I (A) (A) IF Forward ICurrent (A) IF Forward Current F 16 16 TJ=-55C TJ= 25C TJ= 75C TJ =125C TJ =175C IR Reverse Current (A) 18 18 TJ=-55C TJ= 25C TJ= 75C TJ =125C TJ =175C 200 0.0002 0.0001 100 22 00 00 00 0.5 1 1.5 2 2.5 3 3.5 0.5 1 1.5 2 2.5 3 3.5 VF Forward Voltage (V) VF Forward VF (V)Voltage Figure 1. Forward Characteristics 2 C4D20120D Rev. D 0 0 500500 1000 1000 VR Reverse Voltage (V) 1500 1500 VR Reverse Voltage VR (V) Figure 2. Reverse Characteristics 2000 2000 Typical Performance (Per Leg) 200.0 120 180.0 160.0 80 60 140.0 Duty Duty Duty Duty Duty PTot (W) 10% 20% 30% 50% 70% DC I (A) IF(PEAK) Peak Forward F(peak) Current (A) 100 40 120.0 100.0 80.0 60.0 40.0 20 20.0 0.0 0 25 50 75 100 125 150 25 175 50 75 Tc Case T Temperature C (C) 100 125 150 175 TC C C Figure 3. Current Derating Figure 4. Power Derating 800 70 700 60 600 50 C (pF) Qrr (nC) 500 40 30 400 300 20 200 10 100 0 0 200 400 600 800 VR (V) Figure 5. Recovery Charge vs. Reverse Voltage 3 C4D20120D Rev. D 1000 0 0.1 1 10 100 VR (V) Figure 6. Capacitance vs. Reverse Voltage 1000 Typical Performance 25 25.0 1000 1000 EC Capacitive Energy (uJ) C 20 20.0 (A) IFSMIFSM (A) E (mJ) 15 15.0 10 10.0 100 100 TJ = 25C TJ = 110C 5.05 10 10 1E-05 1E-04 1E-03 1E-02 1.E-05 1.E-04 1.E-03 1.E-02 0.00 0 200 400 600 800 1000 0 200 400 600 800 1000 tp(s) tp (s) VR Reverse Voltage (V) VR (V) Thermal Resistance Junction To Case Impedance,(C/W) ZthJC (oC/W) Figure 7. Typical Capacitance Stored Energy, per leg Figure 8. Non-Repetitive Peak Forward Surge Current versus Pulse Duration (sinusoidal waveform), per leg 0.5 100E-3 0.3 0.1 0.05 10E-3 SinglePulse 0.02 0.01 1E-3 1E-6 10E-6 100E-6 1E-3 Time, tp (s) T (Sec) 10E-3 Figure 9. Device Transient Thermal Impedance 4 C4D20120D Rev. D 100E-3 1 Package Dimensions Package TO-247-3 POS A T V U W Inches Millimeters Min Max Min Max .190 .205 4.83 5.21 A1 .090 .100 2.29 2.54 A2 .075 .085 1.91 2.16 b .042 .052 1.07 1.33 b1 .075 .095 1.91 2.41 b2 .075 .085 1.91 2.16 b3 .113 .133 2.87 3.38 b4 .113 .123 2.87 3.13 c .022 .027 0.55 0.68 D .819 .831 20.80 21.10 D1 .640 .695 16.25 17.65 D2 .037 .049 0.95 1.25 E .620 .635 15.75 16.13 E1 .516 .557 13.10 14.15 E2 .145 .201 3.68 5.10 E3 .039 .075 1.00 1.90 E4 .487 .529 12.38 13.43 e .214 BSC N 3 5.44 BSC 3 L .780 .800 19.81 20.32 4.40 L1 .161 .173 4.10 OP .138 .144 3.51 3.65 Q .216 .236 5.49 6.00 S .238 .248 6.04 6.30 T 9 11 9 11 U 9 11 9 11 V 2 8 2 8 W 2 8 2 8 Recommended Solder Pad Layout Part Number Package Marking C4D20120D TO-247-3 C4D20120 TO-247-3 Note: Recommended soldering profiles can be found in the applications note here: http://www.cree.com/power_app_notes/soldering 5 C4D20120D Rev. D Diode Model Diode Model CSD04060 VfT = VT+If*RT Vf T = VT + If*R T V = 0.98+(T * -1.71*10-3) VT= 0.965 +T(Tj * -1.3*10-3J) -4 R = 0.040+(T -3 J* 5.32*10 ) RT= 0.096 +T(T j * 1.06*10 ) Note: Tj = Diode Junction Temperature In Degrees Celsius, valid from 25C to 175C VT RT Notes * RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Documentation sections of www.cree.com. * REACh Compliance REACh substances of high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future,please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. * This product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defibrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, or air traffic control systems. Copyright (c) 2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree, the Cree logo, and Zero Recovery are registered trademarks of Cree, Inc. 6 C4D20120D Rev. D Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5451 www.cree.com/power Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cree, Inc.: C4D20120D