Product Specification PE4237 SPDT UltraCMOSTM RF Switch DC - 4000 MHz Product Description The PE4237 RF Switch is designed to cover a broad range of applications from near DC to 4000 MHz. This reflective switch integrates on-board CMOS control logic driven by a single-pin, low voltage CMOS or TTL control input. Using a nominal +3volt power supply, a 1 dB compression point of +32 dBm can be achieved. The PE4237 also exhibits outstanding isolation of better than 43 dB at 1000 MHz and is offered in a small 3x3 mm DFN package. Features Single 3.0-volt power supply Low insertion loss: 0.35 dB at 1000 MHz, 0.45 dB at 2000 MHz High isolation of 43 dB at 1000 MHz, 35 dB at 2000 MHz Typical 1 dB compression point of +32 dBm The PE4237 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Single-pin CMOS or TTL logic control Available in a 6-lead DFN package Figure 1. Functional Diagram Figure 2. Package Type RFC ESD 6-lead DFN RF1 ESD ESD CMOS Control Driver CTRL Table 1. Electrical Specifications @ +25 C, VDD = 3 V (ZS = ZL = 50 ) Parameter Conditions Operation Frequency1 Minimum Typical DC 0.35 0.45 Maximum Units 4000 MHz 0.50 0.60 dB dB Insertion Loss 1000 MHz 2000 MHz Isolation - RFC to RF1/RF2 1000 MHz 2000 MHz 41 33 43 35 dB dB Isolation - RF1 to RF2 1000 MHz 2000 MHz 33.5 26.5 35 28 dB dB Return Loss 1000 MHz 2000 MHz 19 10.5 24 14 dB dB `ON' Switching Time 50% CTRL to 0.1 dB final value, 2 GHz 200 ns `OFF' Switching Time 50% CTRL to 25 dB isolation, 2 GHz 90 ns 15 mVpp 32 dBm Video Feedthrough2 Input 1 dB Compression 2000 MHz 30 Input IP3 2000 MHz, 17 dBm 50 dBm Notes: 1. Device linearity will begin to degrade below 10 MHz. 2. The DC transient at the output of any port of the switch when the control voltage is switched from Low to High or High to Low in a 50 test set-up, measured with 1ns risetime pulses and 500 MHz bandwidth. Document No. 70-0071-06 www.psemi.com (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 8 PE4237 Product Specification Figure 3. Pin Configuration Table 4. Absolute Maximum Ratings Symbol RF2 1 GND 2 RF1 3 6 Exposed Solder Pad - Shorted to Pin 2 (bottom side) RFC VDD CTRL 4 VDD VCTRL Pin No. Pin Name 1 RF2 RF2 port.1 GND Ground Connection. Traces should be physically short and connected to the ground plane. This pin is connected to the exposed solder pad that also must be soldered to the ground plane for best performance. 2 Description RF1 RF1 port. 4 VDD Nominal 3 V supply connection. 5 CTRL CMOS or TTL logic level: High = RFC to RF1 signal path Low = RFC to RF2 signal path 6 RFC Common RF port for switch.1 Notes: 1. All RF pins must be DC blocked with an external series capacitor or held at 0 VDC. Parameter Min Typ Max Units VDD Power Supply Voltage 2.7 3.0 3.3 V 29 35 A 85 C Control Voltage High Control Voltage Low -40 0.7xVDD V 0.3xVDD V Moisture Sensitivity Level The Moisture Sensitivity Level rating for the PE4237 in the 6-lead 3x3 DFN package is MSL1. (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 8 -0.3 4.0 V -0.3 VDD+ 0.3 V 5.0 V Storage temperature range 150 C PIN Input power (50 ) 35 dBm 250 V -65 ESD voltage (Human Body Model) Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. Control Logic Input Table 5. Control Logic Truth Table Table 3. Operating Ranges TOP Operating temperature range Units Voltage on CTRL input Control Voltage IDD Power Supply Current (VDD = 3V, VCNTL = 3V) Max The control logic input pin (CTRL) is typically driven by a 3-volt CMOS logic level signal. For flexibility to support systems that have 5-volt control logic drivers, the control logic input has been designed to handle a standard 5-volt TTL control signal. This TTL control signal input must not exceed 5-volts or damage to the switch could result. 1 3 Power supply voltage TST VESD Table 2. Pin Descriptions Min Voltage on any input except for the CTRL input VI 5 Parameter/Conditions Signal Path CTRL = CMOS or TTL High RFC to RF1 CTRL = CMOS or TTL Low RFC to RF2 Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 4. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Document No. 70-0071-06 UltraCMOSTM RFIC Solutions PE4237 Product Specification Typical Performance Data @ -40 C to 85 C (Unless Otherwise Noted) Figure 4. Insertion Loss - RFC to RF1 Figure 5. Input 1dB Compression Point 0 40 -40 8C -40 C -0.5 85 C 25 C -0.75 30 1dB Compression Point (dBm) Insertion Loss (dB) -0.25 -1 85 8C 25 8C 20 10 -1.25 -1.5 0 500 1000 1500 2000 2500 3000 3500 0 4000 0 500 1000 Frequency (MHz) 1500 2000 2500 3000 Frequency (MHz) Figure 6. Insertion Loss - RFC to RF2 Figure 7. Isolation - RFC to RF1 T = 25 C 0 0 -40 C -20 -0.5 85 C Isolation (dB) Insertion Loss (dB) -0.25 25 C -0.75 -40 -60 -1 -80 -1.25 -1.5 0 500 1000 1500 2000 2500 Frequency (MHz) Document No. 70-0071-06 www.psemi.com 3000 3500 4000 -100 0 500 1000 1500 2000 2500 3000 3500 4000 Frequency (MHz) (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 8 PE4237 Product Specification Typical Performance Data @ 25 C Figure 9. Isolation - RF1 to RF2, RF2 to RF1 0 0 -20 -20 -40 -40 Isolation (dB) Isolation (dB) Figure 8. Isolation - RFC to RF2 -60 -80 RF2 RF1 -60 -80 -100 -100 0 500 1000 1500 2000 2500 3000 3500 4000 0 500 1000 Frequency (MHz) 2000 2500 3000 3500 4000 3500 4000 Frequency (MHz) Figure 11. Return Loss - RF1, RF2 Figure 10. Return Loss - RFC to RF1, RF2 0 0 -10 -10 Return Loss (dB) Return Loss (dB) 1500 -20 -30 RF2 -20 RF1 -30 -40 -40 0 500 1000 1500 2000 2500 3000 3500 4000 Frequency (MHz) (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 8 0 500 1000 1500 2000 2500 3000 Frequency (MHz) Document No. 70-0071-06 UltraCMOSTM RFIC Solutions PE4237 Product Specification Evaluation Kit The SPDT Switch Evaluation Kit board was designed to ease customer evaluation of the PE4237 SPDT switch. The RF common port is connected through a 50 transmission line to the top left SMA connector, J1. Port 1 and Port 2 are connected through 50 transmission lines to the top two SMA connectors on the right side of the board, J2 and J3. A through transmission line connects SMA connectors J4 and J5. This transmission line can be used to estimate the loss of the PCB over the environmental conditions being evaluated. Figure 12. Evaluation Board Layouts Peregrine Specification 101/0085 The board is constructed of a two metal layer FR4 material with a total thickness of 0.031". The bottom layer provides ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide with ground plane model using a trace width of 0.0476", trace gaps of 0.030", dielectric thickness of 0.028", metal thickness of 0.0021" and r of 4.4. J6 provides a means for controlling DC and digital inputs to the device. Starting from the lower left pin, the second pin to the right (J6-3) is connected to the device CNTL input. The fourth pin to the right (J6-7) is connected to the device VDD input. A decoupling capacitor (100 pF) is provided on both CTRL and VDD traces. It is the responsibility of the customer to determine proper supply decoupling for their design application. Removing these components from the evaluation board has not been shown to degrade RF performance. Document No. 70-0071-06 www.psemi.com Figure 13. Evaluation Board Schematic Peregrine Specification 102/0110 (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 8 PE4237 Product Specification Figure 14. Package Drawing 06L SLP (3x3mm) 6-lead DFN NOTE: The exposed solder pad (on the bottom of the package) is electrically connected to pin 2 (fused.) Figure 15. Marking Specifications 4237 YYWW ZZZZZ YYWW = Date Code (last two digits of year and work week) ZZZZZ = Last five digits of Lot Number (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 8 Document No. 70-0071-06 UltraCMOSTM RFIC Solutions PE4237 Product Specification Figure 16. Tape and Reel Specifications 6-lead DFN Tape Feed Direction Pin 1 Top of Device Table 6. Dimensions Dimension DFN 3x3 mm Ao 3.23 0.1 Bo 3.17 0.1 Ko 1.37 0.1 P 4 0.1 W 8 +0.3, -0.1 T 0.254 0.02 R7 Quantity 3000 R13 Quantity N.A. Device Orientation in Tape Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel Table 7. Ordering Information Order Code Part Marking Description 4237-51 4237 PE4237G-06DFN 3x3mm-12800F Green 6-lead 3x3 mm DFN Tape or loose 4237-52 4237 PE4237G-06DFN 3x3mm-3000C Green 6-lead 3x3 mm DFN 3000 units / T&R 4237-00 PE4237-EK PE4237-06DFN 3x3mm-EK Evaluation Kit 1 / Box Document No. 70-0071-06 www.psemi.com Package Shipping Method (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 8 PE4237 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation Peregrine Semiconductor, Asia Pacific (APAC) 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Europe Peregrine Semiconductor Europe Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 High-Reliability and Defense Products Peregrine Semiconductor, Korea #B-2607, Kolon Tripolis, 210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-943 South Korea Tel: +82-31-728-3939 Fax: +82-31-728-3940 Peregrine Semiconductor K.K., Japan Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Americas San Diego, CA, USA Phone: 858-731-9475 Fax: 848-731-9499 Europe/Asia-Pacific Aix-En-Provence Cedex 3, France Phone: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). (c)2003-2009 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 8 The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS, HaRP, MultiSwitch and DuNE are trademarks of Peregrine Semiconductor Corp. Document No. 70-0071-06 UltraCMOSTM RFIC Solutions