DS1809Z-010+T&R-W - Maxim Integrated Products, Inc.

1 of 9 011501

FEATURES

 64-position linear taper

 Two nonvolatile wiper storage options

 Operates from +4.5 to +5.5-volt supplies

 Operating Temperature Range:

- Industrial: -40°C to +85°C

 Electronic interface provides either digital or

pushbutton control

 Low-cost alternative to mechanical solutions

 Standard Resistance Values

- DS1809-010 10 kΩ

- DS1809-050 50 kΩ

- DS1809-100 100 kΩ

PIN DESCIPTION

VCC - Supply Voltage

RH - High End of Resistor

RL - Low End of Resistor

RW - Wiper Terminal

UC - Up Control Input

DC - Down Control Input

STR - Storage Enable Input

GND - Ground

PIN ASSIGNMENT

DESCRIPTION

The DS1809 Dallastat is a nonvolatile digitally controlled potentiometer that provides 64 uniform wiper

positions over the entire resistor range; including the high-end and low-end terminals of the device. The

DS1809 is a low power device capable of operating from power supplies of +4.5V to +5.5V. The device

is ideal for low-power, portable, or battery powered applications.

Wiper position is maintained in the absence of power. This is accomplished via the use of an EEPROM

cell array. The device provides for two storage methods, which include an auto-store capability and a

command-initiated storage function. The EEPROM cell array is specified to accept greater than 50k

writes. Storage of the wiper position is discussed in the Wiper Storage section of this datasheet.

Wiper positioning is controlled via a patented dual pushbutton (or contact closure) interface. For simple

pushbutton-controlled applications or CPU-generated control signals, external debounce circuitry is not

needed. The control interface will support both repetitive pulse inputs and continuous pulse (“push-and-

hold”) inputs. Repetitive pulse and continuous pulse control as well as timing diagrams are discussed in

the section entitled “OPERATION.”

DS1809

Dallastat

www.dalsemi.com

RH1 8V

UC 2 7 DC

STR 3 6 RW

RL4 5 GND

8-Pin DIP

8-Pin SOIC (150-mil)

8-Pin µSOP (118-mil)

DS1809

2 of 9

The DS1809 is available in standard 10 kΩ, 50 kΩ, and 100 kΩ=resistor versions. The DS1809 is

provided as an industrial temperature grade part only. Available packaging for the DS1809 include an 8-

lead (300-mil) DIP an 8-lead (150-mil) SOIC, and an 8-lead (118-mil) µSOP.

BLOCK DIAGR AM Figure 1

OPERATION

The DS1809 Dallastat is a digitally controlled, nonvolatile potentiometer. A block diagram of the

DS1809 is shown in Figure 1. The DS1809 is a linear potentiometer providing 64-uniform wiper

positions over the entire resistor range including the end-terminals. All three potentiometer terminals of

the device are accessible. These terminals include RH, RL, and RW. RH and RL are the end-terminals of the

potentiometer. These terminals will have a constant resistance between them as defined by the

potentiometer value chosen: 10 kΩ, 50 kΩ, or the 100 kΩ=version. Functionally, RH and RL are

interchangeable. The wiper terminal, RW, is the multiplexed terminal and can be set to one of the 64 total

positions that exist on the resistor ladder including the RH and RL terminals.

Control of the wiper (RW) position setting is accomplished via the two inputs UC and DC. The UC and

DC control inputs, when active, determine the direction on the resistor array that the wiper position will

move. The UC (up control) control input is used to move the wiper position towards the RH terminal. The

DC (down control) control input is used to move wiper position towards the RL terminal.

The control inputs UC and DC are active low inputs that interpret input pulse widths as the means of

controlling wiper movement. Internally, these inputs are pulled up to VCC via a 100 kΩ=resistance. A

transition from a high-to-low on these inputs is considered the beginning of pulse input activity.

A single pulse on the UC or DC input is defined as being greater than 1 millisecond but lasting no longer

that ½ second. This type pulse input will cause the wiper position of the Dallastat to move one position.

Multiple pulse inputs (repetitive pulse inputs) can be used to step through each wiper position of the

device. The requirement for a repetitive pulse train on the UC or DC inputs is that pulses must be

separated by a minimum high time of 1 millisecond. If this is not the case the Dallastat will ignore that

pulse input.

A continuous pulse input (“push and hold”) is defined as lasting longer that ½ second. A continuous pulse

input will cause the wiper position to move one position every 100 milliseconds following the initial ½-

DS1809

3 of 9

second hold time. The total time to transcend the entire potentiometer given a continuous pulse input is

provided by the equation:

½(second) + 62 X 100 ms = 6.7 (seconds)

If the wiper position of the DS1809 is incremented to an end-position, it will stay at that position until the

device receives an opposite direction input pulse command over the UC or DC inputs. For example, if the

wiper position is incremented to the RH terminal using the UC input control, it will stay at that position

until UC is first deactivated, and then the DC input is activated to move the wiper position towards the RL

terminal.

The UC and DC control inputs are designed to support simple pushbutton inputs or CPU generated

inputs. Figure 2 illustrates the requirements for pushbutton generated controls. For manual pushbutton

controls all that is required are the desired pushbuttons to implement contact closure. No external

debounce or timing circuitry is needed to support the pushbutton operation.

Applications using CPU generated controls must power the UC and DC control pins in a high state to

avoid any inadvertent wiper position movement. To help prevent inadvertent wiper position movement

during a power-up, the DS1809 locks out the control port inputs for a minimum time of 10 ms.

WIPER STORAGE

As stated earlier, the DS1809 provides for two methods of nonvolatile wiper storage using internal

EEPROM memory cells. These two methods include an autostore configuration and a command initiated

storage operation, both of which utilize the STR input pin. The EEPROM cell array of the DS1809 is

designed to accept greater than 50k writes.

AUTOSTORAGE

The autostore configuration is designed to provide wiper position storage as the part powers down;

writing the current wiper position into memory. The configuration for initiating the automatic storage

capability of the DS1809 is shown in Figure 3. As shown in this configuration, two external devices are

required to insure proper wiper storage. This includes a Schottky diode and a 10-uf capacitor. The

automatic store configuration will cause the DS1809 to initiate storage of wiper position when power

(VCC) to the device is removed. The 10-uF capacitor and Schottky diode are used to provide supplemental

power for wiper storage.

COMMAND-INITIATED WIPER STORAGE

The DS1809 will also support a command-initiated wiper storage operation during powered conditions.

For command initiated storage the STR pin should be held in a low state on power-up; otherwise the part

will assume an autostore configuration. As shown in Figure 5, a low-to-high pulse lasting at least 1 µs on

the STR input will cause the DS1809 to initiate the storage of the current wiper position into EEPROM

when VCC is present.

DS1809

4 of 9

PUSHBUTTON CONFIGURATION Figure 2

It is assumed that the STR input will be controlled by either external logic or CPU driven. No external

capacitors or diodes are needed for the command-initiated storage operation.

The STR input will take precedence over the pushbutton inputs UC and DC.

AUTOSTORE CONFIGURATION Figure 3

DS1809

5 of 9

PUSHBUTTON TIMING DI AGRAMS Figure 4

If during any pushbutton activity the STR input is activated, pushbutton operation will be suspended until

the storage of EEPROM has been completed. Once complete, pushbutton inputs, if still active, will

resume from the point of suspension. Command initiated storage operations will require a minimum of

4 ms to complete the storage operation. This 4 ms is measured from the rise of STR input (see Figure 5).

For applications not requiring or using the nonvolatile memory feature of the DS1809, it is recommended

that the STR input be connected to GND.

COMMAND INITIATED WIPER STORAGE - Figure 5

DS1809

6 of 9

ABSOLUTE MAXIMUM RA TINGS*

Voltage on Any Pin Relative to Ground -1.0V to +7.0V

Operating Temperature -40°C to +85°C; industrial

Storage Temperature -55°C to +125°C

Soldering Temperature See J-STD-020A Specification

* This is a stress rating only and functional operation of the device at these or any other conditions above

those indicated in the operation sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods of time may affect reliability.

RECOMMENDED DC OPERATING CONDITIONS (-40°C to +85 °C)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Supply Voltage VCC +4.5 5.5 V 1

Resistor Inputs RL,RH,RWGND-0.5 VCC+0.5 V 2

GND GND GND GND 1

DC ELECTRICAL CONDITIONS (-40°C to +85 °C)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Supply Current Active ICC 500 1000 µA 5

Standby Current ISTBY 25 µA 6

Logic Input High VIH +2.0 VCC+0.5 V 6,11

Logic Input Low VIL -0.5 +0.8

+0.6

V 6,11

Input Leakage IIL -1 +1 µA 3

Wiper resistance RWIPER 400 Ω

Wiper Current IW1mA

Storage Pin Current (STR) ISP 5 8 µA 12,18

Wiper Storage Time tWST 4ms19

DS1809

7 of 9

AC ELECTRICAL CONDITIONS

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Single Input Pulse Width tPW 1 DC ms 4,5,7,9

Repetitive Pulse High Time tHPW 1DCms

4,5,7,8,9

Continuous Pulse tCCP 1DC ms 4,5,7,8,9

Storage Control Pulse tSTR 1 µs 10,12

Capacitance CIN 510pF10

ANALOG RESISTOR CHARACTERISTICS ELECTRICAL CONDITIONS

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

End-to-End Resistor

Tolerance -20 +20 % 14

Absolute Linearity -0.6 +0.6 LSB 15

Relative Linearity -0.25 +0.25 LSB 16

-3 dB Cutoff Frequency fCUTOFF MHz 17

Temperature Coefficient 750 PPM/º

C14

NOTES:

1. All voltages are referenced with respect to ground.

2. Voltages across the potentiometer terminals (RL, RW, RH) cannot exceed VCC or go below ground by

0.5V.

3. Inputs UC and DC are internally pulled-up with resistance of 100 kΩ.

4. UC and DC inputs are internally pulled-up to VCC via a 100 kΩ=resistor.

5. Active current is specified when the inputs UC or DC are active.

6. Standby current is the current consumed when the UC, DC, and STR inputs are inactive.

7. Input pulse width is the minimum time required for an input to cause an increment or decrement.

8. Repetitive pulse inputs on UC or DC will be recognized as long as they are within 500 milliseconds

of each other. Pulses occurring faster than 1 ms apart may not be recognized as individual and

separate pulses.

9. Input pulse timing has tolerances to ±10%.

10. Capacitance values apply at 25°C.

11. For VCC = 5V±10%, maximum VIL =+0.8V. Input logic levels are referenced to ground.

12. If not used STR should be connected to ground.

13. The DS1809 is offered in three values: 10 kΩ, 50 kΩ, and 100 kΩ.

DS1809

8 of 9

14. Valid at 25°C only.

15. Absolute linearity is used to compare measured wiper voltage versus expected wiper voltage as

determined by wiper position. The DS1809 is specified to provide a absolute linearity of ±0.60 LSB.

16. Relative linearity is used to determine the change in voltage between successive tap positions. The

DS1809 is specified to provide a relative linearity specification of ±0.25 LSB.

17. -3 dB cutoff frequency characteristics for the DS1809 depend on the potentiometer’s total resistance.

DS1809-010: 1 MHz; DS1809-050: 200 kHz; and the DS1809-100: 100 kHz.

18. Current leakage on the input control storage pin will require a typical 5 µA and maximum 8 µA to

implement the auto-storage feature.

19. A minimum time of 4 milliseconds between 2.2 volts and 1.7 volts is required on the input to the STR

terminal when using the part in the auto-storage configuration. The 2.2-volt to 1.7-volt range is a

worst case condition for meeting the power-down storage requirements of the part.

DS1809

9 of 9

ORDERING INFORMATION

ORDERING NUMBER PACKAGE OPERATING TEMPERATURE VERSION

DS1809-010 8-PIN DIP -40C to +85C 10 kΩ

DS1809-050 8-PIN DIP -40C to +85C 50 kΩ

DS1809-100 8-PIN DIP -40C to +85C 100 kΩ

DS1809U-010 8-PIN µSOP -40C to +85C 10 kΩ

DS1809U-050 8-PIN µSOP -40C to +85C 50 kΩ

DS1809U-100 8-PIN µSOP -40C to +85C 100 kΩ

DS1809Z-010 8-PIN SOIC -40C to +85C 10 kΩ

DS1809Z-050 8-PIN SOIC -40C to +85C 50 kΩ

DS1809Z-100 8-PIN SOIC -40C to +85C 100 kΩ