HEXFET® Power MOSFET
10/08/04
Parameter Max. Units
ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 9.3
ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 6.5 A
IDM Pulsed Drain Current 37
PD @TC = 25°C Power Dissipation 82 W
Linear Derating Factor 0.5 W/°C
VGS Gate-to-Source Voltage ±20 V
EAS Single Pulse Avalanche Energy94 mJ
IAR Avalanche Current9.3 A
EAR Repetitive Avalanche Energy8.2 mJ
dv/dt Peak Diode Recovery dv/dt 8.1 V/ns
TJOperating Junction and -55 to +175
TSTG Storage Temperature Range
Soldering Temperature, for 10 seconds 300 (1.6mm from case ) °C
Mounting torque, 6-32 or M3 srew10 lbf•in (1.1N•m)
Absolute Maximum Ratings
Description
VDSS = 200V
RDS(on) = 0.30 Ω
ID = 9.3A
S
D
G
lAdvanced Process Technology
lDynamic dv/dt Rating
l175°C Operating Temperature
lFast Switching
lFully Avalanche Rated
lEase of Paralleling
lSimple Drive Requirements
D2Pak
IRF630NS
TO-220AB
IRF630N TO-262
IRF630NL
IRF630N
IRF630NS
IRF630NL
Fifth Generation HEXFET® Power MOSFETs from
International Rectifier utilize advanced processing
techniques to achieve extremely low on-resistance per
silicon area. This benefit, combined with the fast switching
speed and ruggedized device design that HEXFET Power
MOSFETs are well known for, provides the designer with an
extremely efficient and reliable device for use in a wide
variety of applications.
The TO-220 package is universally preferred for all
commercial-industrial applications at power dissipation levels
to approximately 50 watts. The low thermal resistance and
low package cost of the TO-220 contribute to its wide
acceptance throughout the industry.
The D2Pak is a surface mount power package capable of
accommodating die sizes up to HEX-4. It provides the
highest power capability and the lowest possible on-
resistance in any existing surface mount package. The
D2Pak is suitable for high current applications because of its
low internal connection resistance and can dissipate up to
2.0W in a typical surface mount application.
The through-hole version (IRF630NL) is available for low-
profile application.
www.irf.com 1
PD - 94005B
http://store.iiic.cc/
www.irf.com 2
IRF630N/S/L
S
D
G
Parameter Min. Typ. Max. Units Conditions
ISContinuous Source Current MOSFET symbol
(Body Diode) ––– ––– showing the
ISM Pulsed Source Current integral reverse
(Body Diode)––– ––– p-n junction diode.
VSD Diode Forward Voltage ––– ––– 1.3 V TJ = 25°C, IS = 5.4A, VGS = 0V
trr Reverse Recovery Time ––– 117 176 n s TJ = 25°C, IF = 5.4A
Qrr Reverse Recovery Charge ––– 542 813 nC di/dt = 100A/µs
ton Forward Turn-On Time Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Source-Drain Ratings and Characteristics
9.3
37
A
Parameter Min. Typ. Max. Units Conditions
V(BR)DSS Drain-to-Source Breakdown Voltage 200 ––– – –– V VGS = 0V, ID = 250µA
∆V(BR)DSS/∆TJBreakdown Voltage Temp. Coefficient ––– 0.26 ––– V/°C Reference to 25°C, ID = 1mA
RDS(on) Static Drain-to-Source On-Resistance ––– ––– 0.30 ΩVGS = 10V, ID = 5.4A
VGS(th) Gate Threshold Voltage 2.0 ––– 4. 0 V VDS = VGS, ID = 250µA
gfs Forward Transconductance 4.9 ––– ––– S VDS = 50V, ID = 5.4A
––– ––– 25 µA VDS = 200V, VGS = 0V
––– ––– 250 VDS = 160V, VGS = 0V, TJ = 150°C
Gate-to-Source Forward Leakage ––– ––– 10 0 VGS = 20V
Gate-to-Source Reverse Leakage ––– ––– -100 nA VGS = -20V
QgTotal Gate Charge –– – ––– 3 5 ID = 5.4A
Qgs Gate-to-Source Charge ––– –– – 6.5 nC VDS = 160V
Qgd Gate-to-Drain ("Miller") Charge ––– –– – 17 VGS = 10V
td(on) Turn-On Delay Time ––– 7.9 ––– VDD = 100V
trRise Time ––– 14 ––– ID = 5.4A
td(off) Turn-Off Delay Time ––– 27 ––– RG = 13Ω
tfFall Time ––– 15 ––– RD = 18Ω
Between lead,
––– ––– 6mm (0.25in.)
from package
and center of die contact
Ciss Input Capacitance ––– 575 ––– VGS = 0V
Coss Output Capacitance ––– 89 ––– VDS = 25V
Crss Reverse Transfer Capacitance ––– 25 ––– pF ƒ = 1.0MHz
nH
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
LDInternal Drain Inductance
LSInternal Source Inductance ––– –––
S
D
G
IGSS
ns
4.5
7.5
IDSS Drain-to-Source Leakage Current
Thermal Resistance Parameter Typ. Max. Units
RθJC Junction-to-Case ––– 1.83
RθCS Case-to-Sink, Flat, Greased Surface 0.50 ––– °C/W
RθJA Junction-to-Ambient––– 62
RθJA Junction-to-Ambient (PCB mount)––– 40
http://store.iiic.cc/
IRF630N/S/L
www.irf.com 3
0.01
0.1
1
10
100
0.1 1 10 100
20µs PULSE WIDTH
T = 25 C
J°
TOP
BOTTOM
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
V , Drai n-to-Source Voltage (V)
I , Drain-to-Source Current (A)
DS
D
4.5V
0.1
1
10
100
0.1 1 10 100
20µs PULSE WIDTH
T = 175 C
J°
TOP
BOTTOM
VGS
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
4.5V
V , Drain-to-Source Voltage (V)
I , D r ain-to-Source Cur rent (A)
DS
D
4.5V
Fig 2. Typical Output CharacteristicsFig 1. Typical Output Characteristics
Fig 3. Typical Transfer Characteristics
0.1
1
10
100
4.0 5.0 6.0 7.0 8.0 9.0 10.0
V = 5 0 V
20µs PULSE WIDTH
DS
V , Gate-to-Source Voltage (V)
I , Drain-to-Source Current (A)
GS
D
T = 25 C
J°
T = 175 C
J°
-60 -40 -20 020 40 60 80 100 120 140 160 180
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
T , Junct ion Temperat ur e ( C)
R , Drain-to-Source On Resistance
(Normalized)
J
DS(on)
°
V =
I =
GS
D
10V
9.3A
Fig 4. Normalized On-Resistance
Vs. Temperature
http://store.iiic.cc/
www.irf.com 4
IRF630N/S/L
Fig 7. Typical Source-Drain Diode
Forward Voltage
Fig 5. Typical Capacitance Vs.
Drain-to-Source Voltage
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
0.1
1
10
100
1000
1 10 100 100
0
OPERATION IN THIS AREA LIMITED
BY RDS(on)
Single Pulse
T
T = 175 C
= 25 C
°°
J
C
V , Dr ain-to-Source Voltage (V)
I , Drain Current (A)I , Drain Current (A)
DS
D
10us
100us
1ms
10ms
Fig 7. Typical Source-Drain Diode
Forward Voltage
Fig 8. Maximum Safe Operating Area
Fig 6. Typical Gate Charge Vs.
Gate-to-Source Voltage
110 100 1000
VDS, Drai n-t o-Source Voltage ( V )
0
200
400
600
800
1000
1200
C, Capacitance(pF)
Coss
Crss
Ciss
VGS
= 0V, f = 1 MHZ
Ciss
= C
gs
+ C
gd, C
ds
SHORTED
Crss
= C
gd
Coss
= C
ds
+ C
gd
0 5 10 15 20 25 30
0
4
8
12
16
Q , Total Ga te Charge (nC)
V , Gat e-to-Source Volt age (V)
G
GS
I =
D5.4A
V = 40V
DS
V = 100V
DS
V = 160V
DS
0.1
1
10
100
0.2 0.4 0.6 0.8 1.0 1.2
V ,Source-to-Drain Voltage (V)
I , Reverse Drain Current (A)
SD
SD
V = 0 V
GS
T = 25 C
J°
T = 175 C
J°
http://store.iiic.cc/
IRF630N/S/L
www.irf.com 5
RD
Fig 9. Maximum Drain Current Vs.
Case Temperature
Fig 10a. Switching Time Test Circuit
V
DS
9
0%
1
0%
V
GS t
d(on)
t
r
t
d(off)
t
f
Fig 10b. Switching Time Waveforms
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
VDS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
VGS
RG
D.U.T.
10V
+
-
25 50 75 100 125 150 175
0
3
6
9
12
T , Case Tem perature( C)
I , Drain C ur rent ( A)
°
C
D
Fig 9. Maximum Drain Current Vs.
Case Temperature
Fig 10a. Switching Time Test Circuit
V
DS
9
0%
1
0%
V
GS t
d(on)
t
r
t
d(off)
t
f
Fig 10b. Switching Time Waveforms
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
VDS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
VGS
RG
10V
VDD
25 50 75 100 125 150 175
0
3
6
9
12
T , Case Tem perature( C)
I , Drain C ur rent ( A)
°
C
D
0.01
0.1
1
10
0.00001 0.0001 0.001 0.01 0.1 1
Notes:
1. Duty factor D =t / t
2. Peak T =P x Z + T
1 2
JDM thJC C
P
t
t
DM
1
2
t , Rectangul ar Pulse Duration (sec)
Thermal Response(Z )
1
thJC
0.01
0.02
0.05
0.10
0.20
D = 0.50
SINGLE PULSE
(THERMAL RESPONSE)
http://store.iiic.cc/
www.irf.com 6
IRF630N/S/L
Q
G
Q
GS
Q
GD
V
G
Charge
D.U.T. V
D
S
I
D
I
G
3mA
V
GS
.3µF
50KΩ
.2µF
12V
Current Regulator
Same Type as D.U.T.
Current Sampling Resistors
+
-
10 V
Fig 13b. Gate Charge Test Circuit
Fig 13a. Basic Gate Charge Waveform
Fig 12b. Unclamped Inductive Waveforms
Fig 12a. Unclamped Inductive Test Circuit
tp
V
(BR)DSS
AS
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
R
G
I
AS
0.01
Ω
t
p
D.U.T
L
VDS
+
-V
DD
DRIVER
A
15V
20V
25 50 75 100 125 150 175
0
50
100
150
200
Starting T , Junction Temperat ur e( C)
E , Singl e Pul s e Aval anche Ener gy ( m J)
J
AS
°
ID
TOP
BOTTOM
2.2A
3.8A
5.4A
http://store.iiic.cc/
IRF630N/S/L
www.irf.com 7
P.W. Period
di/dt
Diode Recovery
dv/dt
Ripple ≤5%
Body Diode Forward Drop
R
e-Applied
V
oltage
Reverse
Recovery
Current Body Diode Forward
Current
V
GS
=10V
V
DD
I
SD
Driver Gate Drive
D.U.T. I
SD
Waveform
D.U.T. V
DS
Waveform
Inductor Curent
D = P.W.
Period
+
-
+
+
+
-
-
-
Fig 14. For N-Channel HEXFET® Power MOSFETs
* VGS = 5V for Logic Level Devices
Peak Diode Recovery dv/dt Test Circuit
RG
VDD
• dv/dt controlled by RG
• Driver same type as D.U.T.
• ISD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
D.U.T Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
*
http://store.iiic.cc/
www.irf.com 8
IRF630N/S/L
LEAD ASSIGNMENTS
1 - GATE
2 - DRAIN
3 - SOURCE
4 - DRAIN
- B -
1.32 (.052)
1.22 (.048)
3X 0.55 (.022)
0.46 (.018)
2.92 (.115)
2.64 (.104)
4.69 (.185)
4.20 (.165)
3X 0.93 (.037)
0.69 (.027)
4.06 (.160)
3.55 (.140)
1.15 (.045)
MIN
6.47 (.255)
6.10 (.240)
3.78 (.149)
3.54 (.139)
- A -
10.54 (.415)
10.29 (.405)
2.87 (.113)
2.62 (.103)
15. 24 (.60 0)
14. 84 (.58 4)
14.09 (.555)
13.47 (.530)
3X 1.40 (.055)
1.15 (.045)
2.54 (.100)
2X
0.36 (.014) M B A M
4
1 2 3
NOTES:
1 DIMENSIONING & TOLERANCING PER ANSI Y14.5M, 1982. 3 OUTLINE CONFORMS TO JEDEC OUTLINE TO-220AB.
2 CONTROLLIN G DI MENSIO N : INCH 4 HEATSI N K & LEAD MEASUREMENTS DO NOT INCLUDE BURRS.
HEXFET
1- GAT E
2- DRAIN
3- SOURCE
4- DRAIN
LEAD ASSIGNMEN TS
IGBTs, CoPAC
K
1- GAT E
2- C OLLEC T OR
3- EMITTER
4- C OLLEC T OR
TO-220AB Package Outline
Dimensions are shown in millimeters (inches)
TO-220AB Part Marking Information
EXAMPLE:
IN THE ASSEMBLY LINE "C"
THIS IS AN IRF1010
LOT CODE 1789
ASSEMBLED ON WW 19, 1997 PAR T NU MBE
R
AS S EMBLY
LOT CODE
DATE CODE
YEAR 7 = 1997
LINE C
WEEK 1 9
LOGO
RECTIFIER
INTERNATIONAL
Note: "P" in assembly line
position indicates "Lead-Free"
http://store.iiic.cc/
IRF630N/S/L
www.irf.com 9
D2Pak Part Marking Information
D2Pak Package Outline
Dimensions are shown in millimeters (inches)
Note: "P" in assembly line
position indicates "Lead-Free"
F530S
THIS IS AN IRF530S WITH
LOT CODE 8024
ASSEMBLED ON WW 02, 2000
IN THE ASSEMBLY LINE "L"
ASSEMBLY
LOT CODE
INTERNATIONAL
RECTIFIER
LOGO
PART NUMBE
R
DATE CODE
YEAR 0 = 2000
WEEK 02
LINE L
OR
F530S
A = ASSEMBLY SITE CODE
WEEK 02
P = DES IGNAT ES LE AD-FRE E
PRODUCT (OPTIONAL)
RECTIFIER
INTERNATIONAL
LOGO
LOT CODE
ASSEMBLY YEAR 0 = 2000
DATE C ODE
PART NUMBER
http://store.iiic.cc/
www.irf.com 10
IRF630N/S/L
TO-262 Part Marking Information
TO-262 Package Outline
Dimensions are shown in millimeters (inches)
ASSEMBLY
LOT CODE
RECTIFIER
INTERNATIONAL
ASSEMBLED ON WW 19, 1997
Note: "P" i n assembly line
po s it io n indicates "L ead-Free"
IN THE ASSEMBLY LINE "C" LOGO
THIS IS AN IRL3103L
LOT CODE 1789
EXAMPLE:
LINE C
DATE CODE
WEEK 19
YEAR 7 = 1997
PAR T NUMBER
PART NUMBER
LOGO
LOT CODE
ASSEMBLY
INTERNATIONAL
RECTIFIER
PRODUCT (OPT IONAL)
P = DES IGNAT ES LE AD-FREE
A = ASSEMBLY SITE CODE
WEEK 19
YEAR 7 = 1997
DATE CODE
OR
http://store.iiic.cc/
IRF630N/S/L
www.irf.com 11
ISD ≤ 5.4A, di/dt ≤ 28 0A/µs, VDD ≤ V(BR)DSS, TJ ≤ 175°C.
Repetitive rating; pulse width limited by
max. junction temperature.
Notes:
Starting TJ = 25°C, L = 6.5mH
RG = 25Ω, IAS = 5.4A.
Pulse width ≤ 400µs; duty cycle ≤ 2%.
This is only applied to TO-220AB package.
This is applied to D2Pak, when mounted on 1" square PCB ( FR-4 or G-10 Material ).
For recommended footprint and soldering techniques refer to application note #AN-994.
Data and specifications subject to change without notice.
This product has been designed and qualified for the automotive [Q101] (IRF630N)
& industrial market (IRF630NS/L).
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 10/04
TO-220AB package is not recommended for Surface Mount Application.
D2Pak Tape & Reel Information
Dimensions are shown in millimeters (inches)
3
4
4
TRR
F
EED DIRECTION
1.85 (.073)
1.65 (.065)
1.60 (.063)
1.50 (.059)
4.10 (.161)
3.90 (.153)
TRL
F
EED DIRECTION
10.90 (. 429)
10.70 (. 421) 16.10 (. 634)
15.90 (. 626)
1.75 (.0 69)
1.25 (.0 49)
11.60 (. 457)
11.40 (. 449) 15. 42 (. 609)
15.22 (.601)
4.72 (.136)
4.52 (.178)
24.30 (. 957
)
23.90 (. 941
)
0.368 (.0145)
0.342 (.0135)
1.60 (. 063)
1.50 (. 059)
1 3.50 (.532)
1 2.80 (.504)
330.00
(14.173)
MAX.
27.40 (1.079)
23.90 (.941)
60. 00 (2.362
)
MIN.
30. 40 (1.197)
MAX.
26.40 (1 .039)
24.40 (.9 61)
NOTES :
1. COMFORMS TO EIA-418.
2. CONTR O LLING DIMENS ION: MIL LI METER.
3. DIMENS ION MEA SURED @ HUB.
4. I NCLUDES FLANG E DISTORTION @ OUTER EDGE.
http://store.iiic.cc/
Note: For the most current drawings please refer to the IR website at:
http://www.irf.com/package/
http://store.iiic.cc/