www.RFM.com E-mail: info@rfm.com Page 1 of 6
©2009-2010 by RF Monolithics, Inc. XTL1003-1 - 2/3/10
13
C r y s t a l E q u i v a l e n t C i r c u i t
ESR
C
O
Electrical Characteristics
Characteristic Sym Notes Minimum Typical Maximum Units
Nominal Frequency 13.56000 MHz
Mode of Oscillation Fundamental
Storage Temperature Range, Crystal Only -50 +125 °C
Storage Temperature Range, in Tape and Reel -40 +85 °C
Operating Temperature Range -20 +70 °C
Frequency Stability over Operating Temperature Range ±20 ppm (referred to the value at 25 °C)
Frequency Make Tolerance FL±10 ppm @ 25 °C ±3 °C
Equivalent Series Resistance ESR 40 Ω
Shunt Capacitance CO2.0 pF
Motional Capacitance CM4.2 ±20% fF
Nominal Drive Level 10 µW
Load Capacitance CL13.5 pF
Insulation Resistance at 100 VDC 500 MΩ
Aging ±1.0 ppm/year @ 25 °C
Weight 0.037 ±0. 005 g
Stanard Shipping Quantity on 330 mm (13”) Reel 3000 units
Lid Symbolization (in addition to Lot and/or Date Codes) 1003-1 YWWS
SM5032-4 Case
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1. US and international patents may apply.
2. The design, manufacturing process, and specifications of this device are subject to change without notice.
3. RFM, stylized RFM logo , and RF Monolithics, Inc. are registered trademarks of RF Monolithics, In c.
XTL1003-1
13.56000 MHz
Crystal Unit
• Surface Mount Se am-Weld Package
• Good Frequency Stability over Temperatur e
• Excellent Reliability
• Complies with Directive 2002/95/EC (RoHS)
The XTL1003-1 is a surface mount 5.0 x 3.2 mm crystal unit for use in wireless
telecommunications devices, esp ecially where an ultra-miniature package is
needed for mobility.
P b
www.RFM.com E-mail: info@rfm.com Page 2 of 6
©2009-2010 by RF Monolithics, Inc. XTL1003-1 - 2/3/10
Dot indicates Pin 4
1.2 ±0.1
2.2 ±0.1
1.2 ±0.1
1.7 ±0.1
5 . 0 ± 0 . 1
3 . 2 ± 0 . 1
T o p V i e w
D o t i n d i c a t e s P i n 3 l o c a t i o n
0 . 8
± 0 . 1
S i d e V i e w
B o t t o m V i e w
P i n s 2 a n d 4 a r e
c o n n e c t e d t o t h e l i d
2 . 4 ± 0 . 2
1 . 2
± 0 . 1
1 . 4
± 0 . 2
43
21
0 . 8
± 0 . 1
D i m e n s i o n s a r e i n m m
Electrical Connections
Pin Connection
1COSC
2 GND (lid)
3FSKOUT
4 GND (lid)
4-Terminal Surface-Mount Seam Weld Case
5.0 x 3.2 mm Nominal Footprint
SM5032-4 Case
Footprint (mm)
Package Orientation in Carrier Tape
Pin 3
www.RFM.com E-mail: info@rfm.com Page 3 of 6
©2009-2010 by RF Monolithics, Inc. XTL1003-1 - 2/3/10
Reel Dimensions
Tape Dimensions
Notes:
1. Unless otherwise specified, tolerance on dimensions is ±0.1 mm
2. Material is black conductive polystyrene
3. 10 pitch cumulative tolerance is ±0.2 mm
www.RFM.com E-mail: info@rfm.com Page 4 of 6
©2009-2010 by RF Monolithics, Inc. XTL1003-1 - 2/3/10
Typical Reflo w Profile
0
5 0
1 0 0
1 5 0
2 0 0
2 5 0
3 0 0
0 6 0 1 2 0 1 8 0 2 4 0 3 0 0 3 6 0
T e m p e r a t u r e ( d e g C )
R a m p u p P r e h e a t R e f l o w C o o l D o w n
T i m e ( s e c o n d s )
Notes:
1. Maximum peak temperature: 265 degrees C for 8 to 12 seconds
2. Typical reflow temperature: 217 ±5 degrees C for 90 to 100 seconds
www.RFM.com E-mail: info@rfm.com Page 5 of 6
©2009-2010 by RF Monolithics, Inc. XTL1003-1 - 2/3/10
Packing - 3,000 units per reel ma ximum
www.RFM.com E-mail: info@rfm.com Page 6 of 6
©2009-2010 by RF Monolithics, Inc. XTL1003-1 - 2/3/10
R eliability Specifications Referenc e
standard
r esistanc e to Temp./ Duration : 260 ° C /10 secon ds ×2 times E IAJ E D-4701
S olde r ing heat Tot al time : 4 minutes (IR-ref low )
(I R ref low) -300(301)M(II)
Vibr ation Tot al p eak amplitude: 1.5 mm MIL-ST D 2 02F
Vibr ation f r equenc y: 10 t o 55 Hz met hod 201A
S weep per i od: 1.0 minut e
Vibr ation directions: 3 mutually per pendi c ular
Duration: 2 hours per direction
Mec hanic al Dir ec tions: 3 impac ts per axis MI L- S TD 202F
S hoc k Ac c elerat ion: 3000g's,
+
20/-0 % met hod 213C
Dur ation: 0.3 ms ( total 18 shocks)
Wav eform : Half-sine
S older abili t y S older T emper at u re: 265 ± 5°C MI L- S TD 883G
Dur at ion time: 5 ± 0. 5 seconds. met hod 2003
Thermal S hock Heat cycle c onditions MI L- S TD 883G
-55 ° C, 30 minut es <> 125 °C, 30 minut es met hod 1010.7
* cycle time : 10 times
Humidit y t est T emper at ur e: 70 ± 2 °C MI L- STD 202F
Relative humidity: 90~95% met hod 103B
Dur ation: 96 hour s
Dr y heat T emper at ur e: 125 ± 2 °C MI L- S TD 883G
( Aging t est ) Dur at ion: 168 hours met hod 1008.2
c ondition C
PCT test Pressure: 2.06 kg/cm2 (2.03*105 pa) E IAJ E D-4701-3
Temper ature : 121 ± 2 ° C B - 12 3A
Relative humidity : 100%
Dur ation: 24 hour s
Environmental characteristics
Mechanical characteristics
Test name Test process / method
