A1442 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection This device is in production, however, it has been deemed Pre-End of Life. The product is approaching end of life. Within a minimum of 6 months, the device will enter its final, Last Time Buy, order phase. Date of status change: January 30, 2012 Recommended Substitutions: For existing customer transition, and for new customers or new applications, contact Allegro Sales. NOTE: For detailed information on purchasing options, contact your local Allegro field applications engineer or sales representative. Allegro MicroSystems, Inc. reserves the right to make, from time to time, revisions to the anticipated product life cycle plan for a product to accommodate changes in production capabilities, alternative product availabilities, or market demand. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use. A1442 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection Features and Benefits Description The A1442 is a full-bridge motor driver designed to drive lowvoltage, brushless DC motors. Commutation of the motor is achieved by use of a single Hall element to detect the rotational position of an alternating-pole ring magnet. A high-density CMOS semiconductor process allows the integration of all the necessary electronics. This includes the Hall element, the motor control circuitry, and the full output bridge. Low-voltage design techniques have been employed to achieve full device functionality down to low VDD values. This fully integrated single chip solution provides enhanced reliability (including reverse battery protection and output short circuit protection) and eliminates the need for any external support components. Low voltage operation E E P pins Reverse voltage protection on VDD and SL Output short circuit and thermal shutdown protections Soft switching algorithm to reduce audible switching noise and EMI interference Unidirectional working mode provides motor rotation in one direction Hall chopper stabilization technique for precise signal response over operating range Sleep mode pin allowing external logic signal enable/ disable to reduce average power consumption Antistall feature guarantees continuous rotation Low current consumption sleep mode Single-chip solution for high reliability Miniature MLP/DFN package Package: 6 pin MLP/DFN (suffix EW) The A1442 employs a soft-switching algorithm to reduce audible switching noise and EMI interference. A micropower sleep mode can be enabled by an external signal, to reduce current consumption for battery management in portable electronic devices. This feature allows the removal of a FET transistor for switching the device on and off. The A1442 is optimized for vibration motor applications in cellular phones, pagers, electronic toothbrushes, hand-held video game controllers, and low power fan motors. 1.5 mm x 2 mm, 0.40 mm maximum overall height The small package outline and low profile make this device ideally suited for use in applications where printed circuit board area and component headroom are at a premium. It is available in a lead (Pb) free, 6 pin MLP/DFN microleadframe package, with an exposed pad for enhanced thermal dissipation. Approximate scale Functional Block Diagram VDD Output Full Bridge Reverse Battery SLEEP 0.1 F Power and Sleep Mode Control Active Braking Control Stall Detection Hall Element Q1 Q3 Drive Logic and Soft Switching Control VOUT1 VOUT2 Q2 Amp M Q4 Thermal Shutdown Protection GND A1442-DSW, Rev. 2 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection A1442 Selection Guide Package1 Packing MLP/DFN 1.5 mm x 2 mm, 0.4 mm maximum overall height 3000 pieces / 7 in. reel Part Number A1442EEWLT-P2 1Contact Allegro(R) for additional packing options. 2Allegro products sold in DFN package types are not intended for automotive applications. Absolute Maximum Ratings Characteristic Symbol Forward Supply Voltage VDD Notes Reverse Supply Voltage VRDD Output Voltage VOUT VDD > 0 V Reverse Output Voltage VROUT VDD > 0 V SLEEP Input Voltage VIN Peak Output Current IOUTpk Operating Ambient Temperature Units 5.0 V -5.0 V 0 to VDD + 0.3 V -0.3 V 0 to VDD + 0.3 V 400 mA < 1 ms TA Rating -40 to 85 C Junction Temperature TJ(max) 165 C StorageTemperature Tstg -65 to 165 C Pin-out Diagram Range E Terminal List Table Pin VDD 1 SLEEP 2 NC 3 6 VOUT2 PAD 5 VOUT1 4 GND Name 1 VDD 2 SLEEP Function Supply voltage Toggle sleep/enabled modes 3 NC 4 GND No connection 5 VOUT1 First output 6 VOUT2 Second output Ground Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 2 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection A1442 OPERATING CHARACTERISTICS valid over the full VDD and TA range unless otherwise noted Characteristic Symbol Supply Voltage1 VDD Supply Current IDD(ON) Total Output On Resistance2,3 RDS(on) Reverse Battery Current Sleep Input Threshold IRDD Test Conditions Min. Typ. Max. Units 2.0 - 4.2 V VIN >VINHI, , TA = 25C, no load - 4 6 mA VIN < VINLO , TA = 25C - - 10 A VDD = 2 V, IOUT = 70 mA, TA = 25C - 3.9 - VDD = 3 V, IOUT = 70 mA, TA = 25C - 2.6 - VDD = 4 V, IOUT = 70 mA, TA = 25C - 2.2 - VRDD = -4.2 V - - -10 mA Operating, TJ < TJ(max); CBYP = 0.1 F VINHI 0.7xVDD - VINLO - - V 0.2xVDD V Sleep Input Current IIN VIN = 3.0 V - 1.0 5 A Reverse Sleep Current IRIN VRIN = -4.2 V - - -10 mA tRS - 120 - ms tS(CHOP) - 80 - s Restart Delay4 Hall Chopping Settling Time Magnetic Switchpoints2 BOP - 35 75 G BRP -75 -35 - G BHYS - 70 - G B < BRP - LOW - V B > BOP - HIGH - V B < BRP - HIGH - V B > BOP - LOW - 1 A bypass capacitor of 0.1 F is required between VDD and GND for proper device operation through the full specified voltage range. V VOUT1 Output Polarity VOUT2 2 Extended V DD range affects RDS(on) and Bx. 3 Total On Resistance equals either R Q1 + R DS(on) DS(on)Q4 or RDS(on)Q2 + RDS(on)Q3. 4 The Restart Delay is the time the outputs are on or off when the device is attempting a restart. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 3 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection A1442 Characteristic Performance Total Output On-Resistance versus Supply Voltage ILOAD = 150 mA 5.0 4.5 4.0 RDS(on) () 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VDD (V) Functional Description Soft Switching The A1442 device includes a soft-switching algorithm that controls the output switching slew rate for both output pins. As a result the A1442 device is ideal for use in applications requiring low audible switching noise and low EMI interference. E E P pin accepts an external signal that Sleep Mode The SL enables sleep mode. In sleep mode, the current consumption is reduced to an extremely low level, conserving battery power in portable electronics. Antistall Algorithm If a stall condition occurs, the device will execute an antistall algorithm. Device Start-up The start-up behavior of the device output is determined by the applied magnetic field, as specified in the Operating Characteristics table. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 4 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection A1442 Application Information Two typical application circuits are shown in figures 4 and 5. The E E P pin controlled first application circuit shows the device SL by the user. Figure 5 illustrates an application circuit where the E E P pin are connected together. device VDD and SL A bypass capacitor of 0.1 F is required between VDD and GND for proper device operation through the full specified supply voltage range. Note that: No external diode is required for reverse battery protection because the protection is fully integrated into the IC. Thermal shutdown is integrated also. VBATT + VDD System Logic Control CBYP VOUT1 A1442 SLEEP I/O VOUT2 M NC GND Figure 4. Application circuit showing user-controlled sleep/enable mode, while the A1442 remains powered at all times + VBATT VDD System Logic Control VOUT1 A1442 SLEEP I/O VOUT2 CBYP M NC GND Figure 4. Application circuit showing simultaneous user control of power supply and sleep mode. Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 5 A1442 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection Power Derating The device must be operated below the maximum junction temperature of the device, TJ(max). Under certain combinations of peak conditions, reliable operation may require derating supplied power or improving the heat dissipation properties of the application. This section presents a procedure for correlating factors affecting operating TJ. (Thermal data is also available on the Allegro MicroSystems Web site.) The package thermal resistance, RJA, is a figure of merit summarizing the ability of the application and the device to dissipate heat from the junction (die), through all paths to the ambient air. Its primary component is the effective thermal conductivity, K, of the printed circuit board, including adjacent devices and traces. Radiation from the die through the device case, RJC, is relatively small component of RJA. Ambient air temperature, TA, and air motion are significant external factors, damped by overmolding. The effect of varying power levels (power dissipation, PD) can be estimated. The following formulas represent the fundamental relationships used to estimate TJ at given levels of PD. Given: PD = VIN x IIN , (1) T = PD x RJA , and (2) TJ = TA + T (3) For a load of 30 , given common conditions such as: TA= 25C, VDD = 3 V, IDD = 83 mA, VL = 2.43 V, IL = 81 mA and RJA = 250 C/W, then: PD = VDD x IDD - VLIL = 3 V x 83 mA - 2.43 V x 81 mA = 52.17 mW , T = PD x RJA = 52.17 mW x 250 C/W = 13C , and TJ = TA + T = 25C + 13C = 38C A worst-case estimate, PD(max), represents the maximum allowable power level, without exceeding TJ(max), at a selected RJA and TA. VBATT + IDD IL VDD System Logic Control CBYP 0.1 F I/O VOUT1 A1442 SLEEP VOUT2 M NC GND Figure 4. Typical application showing current paths Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 6 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection A1442 Package EW, 6 pin MLP/DFN 1.50 0.15 0.89 F E 6 F 0.50 0.30 6 0.99 F 2.00 0.15 0.70 1.575 A 1 1 0.325 1.10 7X D SEATING PLANE 0.08 C C C PCB Layout Reference View 0.38 0.02 0.50 BSC B +0.055 0.325 -0.045 0.70 0.10 NN YWW 0.25 0.05 1 1 1.25 0.05 G Standard Branding Reference View N = Last two digits of device part number Y = Last digit of year of manufacture W = Week of manufacture 6 1.10 0.10 For Reference Only, not for tooling use (refernce DWG-2856; similar to JEDEC Type 1, MO-229X2BCD) Dimensions in millimeters Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area B Exposed thermal pad (reference only, terminal #1 identifier appearance at supplier discretion) C Reference land pattern layout (reference IPC7351 SON50P200X200X100-9M); All pads a minimum of 0.20 mm from all adjacent pads; adjust as necessary to meet application process requirements and PCB layout tolerances; when mounting on a multilayer PCB, thermal vias at the exposed thermal pad land can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5) D Coplanarity includes exposed thermal pad and terminals E Active Area Depth 0.15 mm REF F Hall Element (not to scale) G Branding scale and appearance at supplier discretion Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 7 Low Voltage Full Bridge Brushless DC Motor Driver with Hall Commutation and Soft Switching, and Reverse Battery, Short Circuit, and Thermal Shutdown Protection A1442 Revision History Revision Revision Date Rev. 2 October 26, 2011 Description of Revision Update Selection Guide Copyright (c)2006-2011, Allegro MicroSystems, Inc. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro's products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the failure of that life support device or system, or to affect the safety or effectiveness of that device or system. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. For the latest version of this document, visit our website: www.allegromicro.com Allegro MicroSystems, Inc. 115 Northeast Cutoff Worcester, Massachusetts 01615-0036 U.S.A. 1.508.853.5000; www.allegromicro.com 8