3M Electronic Handling and Protection Division
6801 River Place Blvd.
Austin, TX 78726-9000
Test
& Burn-In PGA Kit Sockets
Pin Grid Arrays
10
Date Issued: June 20, 2001
TS-0675-09
Sheet
1 of 2
Physical
Insulation
Material: Polyethersyfone (PES)
Flammability:
UL 94V
-0
Color: Black
Marking:
3M Logo & Part Number Identifier
Cam Handle
Material:
Stainless Steel
Contact
Material:
Beryllium Copper
Plating Options:
Electrical
Curr
ent Rating:
1 Amp
Insulation Resistance:
> 1
¥
10
12
W
at 500 Vdc
W
ithstanding V
oltage:
1000 V
rms at Sea Level
Environmental
Temperatur
e Rating Operating:
- 55°
∞
C to + 150°
∞C
Mechanical
A:
When used as a test socket at room temperature 24°
∞
C the socket will last
25,000 actuations.
B:
Based on field experience, under normal burn-in conditions up to a
maximum of 150°
∞
C, the socket should last an average of four years.
• Available in 10 x 10 matrix through 25 x 25
matrix
• Used when only a few test sockets are needed
• Provides individual components ready for
assembly
• Open pattern top plate; load only those contacts
needed for your specific device pin pattern
For
technical, sales or ordering information call
800-328-0411
or visit our website: http://www.3M.com/ehpd
30 m" (0.76 mm) Gold over 50 m" (1.3 mm) Nickel
3M
Electronic Handling and Protection Division
6801 River Place Blvd.
Austin, TX 78726-9000
Test
& Burn-In PGA Kit Socket
Pin Grid Arrays
Part
Number
Matrix Size Description
200-6310-9UN-1900 10 x 10
200-6311-9UN-1900 11 x 11
200-6313-9UN-1900 13 x 13
200-6315-9UN-1900 15 x 15
S k t Kit W/O C t t
200-6317-9UN-1900 17 x 17 Socket Kit W/O Contacts
200-6319-9UN-1900 19 x 19
200-6321-9UN-1900 21 x 21
200-6325-9UN-1900 25 x 25
300-6300-CNA-0002B Each Contact–BeCu/Au Plated
200-4660-14-1900 Set of 10 Extra Hole Plugs
TS-0675-09
Sheet
2 of 2
Ordering Information
4X
Phillips Pan-Hd
#0-80 x 5/16 Long
Assy Screw
10X Hole Plugs
T
op Plate
Contact
( Order Separately )
Cam Plate
Base Plate
Cam Handle
Standard
Handle
Assembly Instructions
1. Load
hole plugs into top plate by
pressing fitting into place.
Remove
from tie bar by cutting
with commercially available 6 1/2
"
flush diagonal cutter pliers.
2.
Place cam plate into recessed
area of base plate, load
contacts in desired locations,
being careful that the bent leaf
of the contact is loaded in
correct position ( away from
cam handle. )
3.
Insert cam handle into position
in the base plate.
4.
Now make a final check that all
contacts are in desired location
and that all are fairly even at the
top. Also check cam to make
sure it is still in position. Now
take the top plate and place into
position and start to lower over
contacts. Start at the rear of the
socket and rotate downward
toward the front and then snap
locating bosses into place.
Several very slight back and
forth motions may be necessary
in order to get contacts to snap
into place. Care should be taken
that too much downward
pressure isn't applied which
could bend or damage the
contacts. Insert screws and
tighten.
5.
Now make an operation check
by rotating handle 90
∞
. Make a
visual check of movement and
closure of all contacts. Rotate
handle and check the freedom
of movement of cam plate and
that the moving leaf of the
contact clears the entry hole. A
continuity check can be made
before final soldering by placing
device in socket, then closing
and making check. Soldering
should be done with socket in
the open position.
Notes:
1 Contact
and extra Hole Plugs are ordered separately
.
2
See T
est & Burn-In PGA socket section on page 29 for dimensional information on assembled sockets.
For
technical, sales or ordering information call
800-328-0411
or visit our website: http://www.3M.com/ehpd
1
