HS-4424RH, HS-4424BRH Data Sheet June 1999 Radiation Hardened Dual, Non-Inverting Power MOSFET Drivers The Radiation Hardened HS-4424RH and HS-4424BRH are non-inverting, dual, monolithic high-speed MOSFET drivers designed to convert TTL level signals into high current outputs at voltages up to 18V. The inputs of these devices are TTL compatible and can be directly driven by our HS-1825ARH PWM device or by our ACS/ACTS and HCS/HCTS type logic devices. The fast rise times and high current outputs allow very quick control of high gate capacitance power MOSFETs, like our Rad Hard FS055, in high frequency applications. The high current outputs minimize power losses in MOSFETs by rapidly charging and discharging the gate capacitance. The output stage incorporates a low voltage lock-out circuit that puts the outputs into a three-state mode when the supply voltage drops below 10V for the HS-4424RH and 7.5V for the HS-4424BRH. Constructed with the Intersil dielectrically isolated Rad Hard Silicon Gate (RSG) BiCMOS process, these devices are immune to Single Event Latch-up and have been specifically designed to provide highly reliable performance in harsh radiation environments. Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed here must be used when ordering. Detailed Electrical Specifications for these devices are contained in SMD 5962-99560. A "hot-link" is provided on our homepage for downloading. www.intersil.com/spacedefense/space.asp 4739.1 Features * Electrically Screened to DESC SMD # 5962-99560 * QML Qualified per MIL-PRF-38535 Requirements * Radiation Environment - Total Dose (Max). . . . . . . . . . . . . . . . . . 3 x 105 RAD(SI) - Latch-Up Immune - Low Dose Rate Immune * IPEAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >2A (Min) * Matched Rise and Fall Times (CL = 4300pF). . . 75ns (Max) * Low Voltage Lock-Out Feature - HS-4424RH . . . . . . . . . . . . . . . . . . . . . . . . . . . < 10.0V - HS-4424BRH . . . . . . . . . . . . . . . . . . . . . . . . . . . < 7.5V * Wide Supply Voltage Range. . . . . . . . . . . . . . . 12V to 18V * Prop Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . 250ns (Max) * Consistent Delay Times with VCC Changes * Low Power Consumption - 40mW with Inputs High - 20mW with Inputs Low * Low Equivalent Input Capacitance . . . . . . . . . .3.2pF (Typ) * ESD Protected . . . . . . . . . . . . . . . . . . . . . . . . . . . >4000V Applications * Switching Power Supplies * DC/DC Converters * Motor Controllers Ordering Information Pinout HS-4424RH, HS-4424BRH (FLATPACK CDFP4-F16) TOP VIEW File Number ORDERING NUMBER INTERNAL MKT. NUMBER TEMP. RANGE (oC) 5962F9956001VXC HS9-4424RH-Q -55 to 125 NC 1 16 NC 5962F9956001QXC HS9-4424RH-8 -55 to 125 IN A 2 15 OUT A HS9-4424RH/Proto HS9-4424RH/Proto -55 to 125 NC 3 14 OUT A GND A 4 13 VCC 5962F9956002VXC HS9-4424BRH-Q -55 to 125 GND B 5 12 VCC 5962F9956002QXC HS9-4424BRH-8 -55 to 125 HS9-4424BRH/Proto HS9-4424BRH/Proto -55 to 125 NC 6 11 OUT B IN B 7 10 OUT B NC 8 9 NC NOTE: Pins 4 and 5, 10 and 11, 12 and 13, 14 and 15 are doublebonded to their same electrical points on the die. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright (c) Intersil Corporation 1999 HS-4424RH, HS-4424BRH Die Characteristics DIE DIMENSIONS: Backside Finish: 4890m x 3370m (193 mils x 133 mils) Thickness: 483m 25.4m (19 mils 1 mil) INTERFACE MATERIALS: Silicon ASSEMBLY RELATED INFORMATION: Substrate Potential: Glassivation: Unbiased (DI) Type: PSG (Phosphorous Silicon Glass) Thickness: 8.0kA 1.0kA ADDITIONAL INFORMATION: Worst Case Current Density: Top Metallization: <2.0 x 105 A/cm2 Type: AlSiCu Thickness: 16.0kA 2kA Transistor Count: 125 Substrate: Radiation Hardened Silicon Gate, Dielectric Isolation Metallization Mask Layout HS-4424RH, HS-4424BRH GND (5) GND (4) IN A (2) IN B (7) OUT B (10) OUT A (15) OUT B (11) OUT A (14) VCC (12) VCC (13) All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site www.intersil.com 2