Intel(R) AtomTM Processor N400 & N500 Series Datasheet - Volume 1 This is volume 1 of 2. Refer to Document Ref# 322848 for Volume 2. June 2011 Revision 003 Document Number: 322847-003 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Legal Lines and Disclaimers UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with this information. The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Intel, [include any Intel trademarks which are used in this document] and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Intel processor numbers are not a measure of performance. Processor numbers differentiate features within each processor family, not across different processor families. Go to: http://www.intel.com/products/processor%5Fnumber/ Enhanced Intel(R) SpeedStep Technology: See the Processor Spec Finder at http://processorfinder.intel.com or contact your Intel representative for more information. Enabling Execute Disable Bit functionality requires a PC with a processor with Execute Disable Bit capability and a supporting operating system. Check with your PC manufacturer on whether your system delivers Execute Disable Bit functionality. *Other names and brands may be claimed as the property of others. Copyright (c) 2011. Intel Corporation. All rights reserved. 2 Specification Update Contents 1 Introduction ..............................................................................................................8 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 2 Signal Description.................................................................................................... 15 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 3 Processor Legacy Signals.................................................................................... 16 System Memory Interface................................................................................... 19 Reset and Miscellaneous Signals .......................................................................... 20 DMI - Direct Media Interface ............................................................................... 21 PLL Signals ....................................................................................................... 22 Analog Display Signals ....................................................................................... 22 LVDS Signals .................................................................................................... 23 TAP Signals ...................................................................................................... 23 Error and Thermal Protection .............................................................................. 24 Processor Core Power Signals.............................................................................. 24 Graphics, DMI and Memory Core Power Signals ..................................................... 25 Ground ............................................................................................................ 25 Functional Description ............................................................................................. 26 3.1 3.2 3.3 3.4 3.5 4 Processor Features ..............................................................................................8 Interfaces...........................................................................................................9 1.2.1 System Memory Support ...........................................................................9 1.2.2 Direct Media Interface Features ................................................................ 10 1.2.3 Integrated Graphics Controller ................................................................. 10 Clocking ........................................................................................................... 11 Power Management Support ............................................................................... 11 Package ........................................................................................................... 11 Terminology ..................................................................................................... 11 References ....................................................................................................... 13 System Block Diagram ....................................................................................... 14 Integrated Memory Controller ............................................................................. 26 3.1.1 System Memory Organization Modes ......................................................... 26 3.1.2 System Memory Technology Supported ..................................................... 26 3.1.3 Rules for populating SO-DIMM slots .......................................................... 27 3.1.4 Intel(R) Fast Memory Access (Intel(R) FMA) Technology Enhancements ............. 28 3.1.5 DRAM Clock Generation........................................................................... 29 Integrated Graphics Controller ............................................................................ 29 3.2.1 3D Graphics Pipeline ............................................................................... 29 3.2.2 Video Engine ......................................................................................... 30 3.2.3 2D Engine ............................................................................................. 31 3.2.4 Display Pipes ......................................................................................... 32 3.2.5 Display Ports ......................................................................................... 32 3.2.6 VESA/VGA Mode..................................................................................... 36 3.2.7 Multiple Display Configurations................................................................. 36 Thermal Sensor................................................................................................. 36 3.3.1 PCI Device 0, Function 0 ......................................................................... 36 Power Management ........................................................................................... 37 Intel(R) Hyper-Threading Technology .................................................................... 37 Electrical Specifications ........................................................................................... 38 4.1 Power and Ground Balls ..................................................................................... 38 Specification Update 3 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 5 Power Management .................................................................................................54 5.1 5.2 5.3 6 Thermal Specifications........................................................................................66 6.1.1 Thermal Diode........................................................................................67 6.1.2 Intel(R) Thermal Monitor ...........................................................................69 6.1.3 Digital Thermal Sensor ............................................................................71 6.1.4 Out of Specification Detection...................................................................72 6.1.5 PROCHOT# Signal Pin .............................................................................72 Package Mechanical Specifications and Ball Information..........................................74 7.1 7.2 4 ACPI States Supported .......................................................................................54 5.1.1 System States........................................................................................54 5.1.2 Processor Idle States...............................................................................54 5.1.3 Integrated Graphics Display States ...........................................................55 5.1.4 Integrated Memory Controller States .........................................................55 5.1.5 DMI States ............................................................................................55 5.1.6 Interface State Combinations ...................................................................55 Processor Core Power Management ......................................................................56 5.2.1 Enhanced Intel SpeedStep(R) Technology ....................................................56 5.2.2 Dynamic Cache Sizing .............................................................................57 5.2.3 Low-Power Idle States.............................................................................57 5.2.4 Thread C-states Description .....................................................................60 5.2.5 Processor Core/Package C-states Description..............................................61 External Thermal Sensor PM_EXTTS1#: Implementation for Fast C4/C4E Exit ............64 Thermal Specifications and Design Considerations...................................................66 6.1 7 Decoupling Guidelines ........................................................................................38 4.2.1 Voltage Rail Decoupling ...........................................................................38 Processor Clocking .............................................................................................39 4.3.1 PLL Power Supply ...................................................................................39 Voltage Identification (VID).................................................................................39 Catastrophic Thermal Protection ..........................................................................41 Reserved or Unused Signals ................................................................................41 Signal Groups ...................................................................................................41 Test Access Port (TAP) Connection .......................................................................42 Absolute Maximum and Minimum Ratings..............................................................42 DC Specifications ...............................................................................................43 4.10.1 Voltage and Current Specifications ............................................................43 4.10.2 Interface DC Specifications ......................................................................47 Package Mechanical Specifications .......................................................................74 7.1.1 Package Mechanical Drawings...................................................................74 7.1.2 Package Loading Specifications .................................................................75 Processor Ballout Assignment ..............................................................................75 Intel Confidential Specification Update Figures Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure 1-1 3-2 3-3 3-4 4-5 5-6 5-7 5-8 5-9 7-10 7-11 7-12 7-13 7-14 Platform Block Diagram ........................................................................... 14 LVDS Signals and Swing Voltage .............................................................. 34 LVDS Clock and Data Relationship ............................................................ 34 Panel Power Sequencing.......................................................................... 35 VCC and ICC Processor Loadline................................................................. 45 Idle Power Management Breakdown of the Processor Thread ........................ 58 Thread C-state ....................................................................................... 59 Processor Core Low-power States ............................................................. 59 PM_EXTTS1#/DPSLPVR Implementation for Fast C4/C4E Exit ....................... 65 Package Mechanical Drawings .................................................................. 74 Package Pinmap (Top View, Upper-Left Quadrant) ...................................... 75 Package Pinmap (Top View, Upper-Right Quadrant) .................................... 76 Package Pinmap (Top View, Lower-Left Quadrant) ...................................... 77 Package Pinmap (Top View, Lower-Right Quadrant) .................................... 78 Tables Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table Table 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 3-16 3-17 3-18 3-19 4-20 4-21 4-22 4-23 4-24 Table Table Table Table Table Table 4-25 4-26 4-27 4-28 4-29 4-30 Signal Types .......................................................................................... 15 Signal Description Buffer Types ................................................................ 15 Processor Legacy Signals......................................................................... 16 System Memory Interface........................................................................ 19 Memory Reference and Compensation ....................................................... 20 Reset and Miscellaneous Signals ............................................................... 20 DMI - Processor to Chipset Serial Interface ................................................ 21 PLL Signals ............................................................................................ 22 Analog Display Signals ............................................................................ 22 LVDS Signals ......................................................................................... 23 TAP Signals ........................................................................................... 23 Error and Thermal Protection ................................................................... 24 Processor Core Power Signals................................................................... 24 Power Signals ........................................................................................ 25 Ground ................................................................................................. 25 Supported SO-DIMM Module Configurations ............................................... 27 Supported DDR3 S0-DIMM module Configurations ...................................... 27 Analog Port Characteristics ...................................................................... 33 Panel Power Sequencing Timing Parameters............................................... 35 Voltage Identification Definition ................................................................ 39 Processor Absolute Minimum and Maximum Ratings .................................... 42 Processor Core Active and Idle Mode DC Voltage and Current Specifications ... 44 Processor I/O Buffer Supply DC Voltage and Current Specifications ............... 46 Input Clocks (BCLK, HPL_CLKIN, REFCLKIN, EXP_CLKIN) Differential Specification .......................................................................................... 47 DDR2/DDR3 Signal Group DC Specifications............................................... 47 GTL Signal Group DC Specifications .......................................................... 48 Legacy CMOS Signal Group DC Specification .............................................. 49 Open Drain Signal Group DC Specification.................................................. 50 PWROK and RSTIN# DC Specification........................................................ 50 CPUPWRGOOD DC Specification................................................................ 50 Specification Update 5 Table 4-31 Table 4-32 Table 4-33 Table 4-34 Table 4-35 Table Table Table Table Table Table Table Table Table Table Table Table Table 6 4-36 5-37 5-38 5-39 5-40 5-41 5-42 5-43 5-44 6-45 6-46 6-47 7-48 DDR3_DRAM_PWROK DC Specification ......................................................51 TAP Signal Group DC Specification ............................................................52 CRT_DDC_DATA. CRT_DDC_CLK DC, LDDC_DATA, LDDC_CLK, LCTLA_CLK, and LCTLB_DATA Specification .......................................................................52 CRT_HSYNC and CRT_VSYNC DC Specification............................................53 LVDS Interface DC Specification (functional operating range, VCCLVDS = 1.8V +/- 5%) .......................................................................53 LVDD_EN, LBLKLT_EN and LBKLT_CTL DC Specification ...............................53 System States........................................................................................54 Processor Core/Package States Support .....................................................54 Integrated Graphics Display Device Control ................................................55 Main Memory States................................................................................55 DMI States ............................................................................................55 G, S and C State combinations .................................................................55 D, S and C state Combinations .................................................................56 Coordination of Thread Low-power States at the Package/Core Level .............60 Power Specifications for the Processor .......................................................67 Thermal Diode Interface ..........................................................................68 Thermal Diode Parameters using Transistor Model.......................................68 Processor Ball List by Ball Name ...............................................................79 Intel Confidential Specification Update Revision History Revision Number 001 002 003 Description * Initial release Revision Date December 2009 * Updated Table 4-22: Added Icc data for Intel(R) AtomTM Processor N470 series as a new SKU * Updated Table 6-45: Added TDP data for Intel Atom Processor N470 as a new SKU * Inserted Intel(R) AtomTM N500 series information to Datasheet April 2010 June 2011 Specification Update 7 Introduction 1 Introduction The document provides DC electrical specifications, pinout and signal definitions, interface functional descriptions, and additional feature information pertinent to the implementation and operation of the processor on its respective platform. Throughout this document, Intel(R) AtomTM Processor N400 Series is referred as the processor and Intel(R) NM10 Family Express Chipset is referred as the chipset. The processor is built on 45-nanometer Hi-K process technology. The processor is designed for a two-chip platform as opposed to the traditional three-chip platforms (processor, GMCH, and ICH). The two-chip platform consists of a processor and a chipset which enables better performance, lower cost, easier validation, and improved x-y footprint. The processor is offered in an BGA559 package. Included in this family of processors is an integrated memory controller (IMC), integrated graphics processing unit (GPU) and integrated I/O (IIO) (such as DMI) on a single silicon die. This single die solution is known as a monolithic processor. 1.1 Processor Features The following list provides some of the key features on this processor: * On die, primary 32-kB instructions cache and 24-kB write-back data cache * Intel(R) Hyper-Threading Technology (2 threads) * On die 512-kB, 8-way L2 cache * Support IA 32-bit and Intel(R) 64 architecture * Intel(R) Streaming SIMD Extensions 2 and 3 (SSE2 and SSE3) and Supplemental Streaming SIMD Extensions 3 (SSSE3) support * Micro-FCBGA8 packaging technologies * Thermal management support via Intel(R) Thermal Monitor 1 (TM1) and Intel(R) Thermal Monitor 1 (TM2) * Support C-state of C0/C1(E)/C2(E)/C4(E) * Enhanced Intel(R) SpeedStep Technology (EIST) * Support L2 dynamic cache sizing * Execute Disable Bit support for enhanced security 8 Datasheet Introduction 1.2 Interfaces 1.2.1 System Memory Support Support DDr2 SDRAMs (N450 and N470 support DDR2 only) * One channel of DDR2 memory (consists of 64-bit of data lines): -- Maximum of two SO-DIMMs in Raw Card-A or Raw Card-C format * Memory DDR2 data transfer rates of 667 MT/s * I/O Voltage of 1.8 V for DDR2 * Non-ECC, unbuffered DDR2 SO-DIMMs only * 512-Mb, 1-Gb and 2-Gb DDR2 DRAM technologies supported * Maximum of 2-GB memory capacity supported -- Maximum 1-GB memory capacity on one SO-DIMM or Memory Down * Memory organizations: -- Two SO-DIMMs -- One SO-DIMM only -- One SO-DIMM and One Memory Down (based on simulations only) * Up to 32 simultaneous open pages (assuming 4 Ranks of 8 Bank Devices) * Partial Writes to memory using Data Mask signals (DM) * On-Die Termination (ODT) * Intel(R) Fast Memory Access (Intel FMA) -- Just-in-Time Command Scheduling -- Command Overlap -- Out-of-Order Scheduling -- Opportunistic Writes * Support memory thermal management scheme to selectively manage reads and/or writes. Memory thermal management can be triggered by either on-die thermal sensor, or by preset limits. Management limits are determined by weighted sum of various commands that are scheduled on the memory interface. * Support DDR3 SDRAMs: * Support for DDR3 at data transfer rate of 667 MT/s * One channel of DDR3 memory (consists of 64-bit of data lines): Maximum of two SO-DIMMs in Raw Card-A or Raw Card-B format * I/O Voltage of 1.5 V for DDR3 Datasheet 9 Introduction * Maximum of 2-GB system memory capacity supported on one SO-DIMM or two SODIMMs * Memory organizations supported (refer to the Platform Design Guide for more details - DIMM populating rules and Clock/Control signals ordering): -- Two SO-DIMMs -- One SO-DIMM only 1.2.2 Direct Media Interface Features * Compliant to Direct Media Interface (DMI) * Support 2 lanes in each direction, point-to-point DMI interface to the chipset * Raw bit-rate on the data pins of 2.5Gb/s, resulting in a real bandwidth per pair of 250MB/s given the 8b/10b encoding used to transmit data across this interface. Does not account for packet overhead and link maintenance * Maximum theoretical bandwidth on interface of 500MB/s in each direction simultaneously, for an aggregate of 1GB/s for the interface * 100-MHz reference clock * 64-bit downstream address (only 36-bit addressable from the processor) * APIC messaging support. Will send Intel-defined "End of Interrupt" broadcast message when initiated by the processor * Message Signaled Interrupt (MSI) messages supported * Power Management state change messages supported * SMI, SCI and SERR error indication * Legacy support for ISA regime protocol (PHOLD/PHOLDA) required for parallel port DMA, floppy drive, and LPC bus masters * Hybrid AC-DC coupling solution between the processor and the chipset * Polarity inversion supported 1.2.3 Integrated Graphics Controller * The integrated graphics controller contains a refresh of the 3rd generation graphics core * Intel(R) Dynamic Video Memory Technology 4.0 * Directx* 9 compliant Pixel Shader 2.0 * 200-MHz render clock frequency * Two display ports: LVDS and RGB -- Integrated single LVDS channel support resolution up to 1280*800 or 1366*768 -- Analog RGB display output up to resolution 1400x1050 @ 60Hz * Intel(R) Clear Video Technology 10 Datasheet Introduction -- MPEG2 Hardware Acceleration -- ProcAmp 1.3 Clocking * Differential Core clock of 166 MHz (BCLKP/BCLKN) * Differential Host clock of 166 MHz (HPL_CLKINP/HPL_CLKINN) * The differential DMI clock of 100 MHz (EXP_CLKINP/EXP_CLKINN) * Display timings are generated from display PLLs that use a 96 MHz or 100 MHz differential clock as reference. * All of the above clocks are capable of tolerating Spread Spectrum clocking. * Memory clocks generated from internal Host PLLs * Host, Memory, DMI, Display PLLs and all associated internal clocks are disabled until PWROK is asserted. 1.4 Power Management Support * Processor Core: -- Full support of ACPI C-states as implemented by the following processor Cstates: C0/C1(E)/C2(E)/C4(E) -- Enhanced Intel SpeedStep(R) Technology * Thermal Management 1 (TM1) and Thermal Management 2 (TM2) * System states: S0, S3, S4 and S5 * DMI: L0s and L1 ASPM power management capability 1.5 Package * The processor is a Micro-FCBGA8 type of package at 22mmx22mm package size 1.6 Terminology (Sheet 1 of 3) Term Datasheet Description BGA Ball Grid Array BLT Block Level Transfer CRT Cathode Ray Tube DDR2 Second generation Double Data Rate SDRAM memory technology DDR3 Third generation Double Data Rate SDRAM memory technology 11 Introduction (Sheet 2 of 3) Term Description DMA Direct Memory Access DMI Direct Media Interface DTS Digital Thermal Sensor ECC Error Correction Code Enhanced Intel SpeedStep(R) Technology Technology that provides power management capabilities to laptops. Execute Disable Bit The Execute Disable bit allows memory to be marked as executable or non-executable, when combined with a supporting operating system. If code attempts to run in non-executable memory the processor raises an error to the operating system. This feature can prevent some classes of viruses or worms that exploit buffer overrun vulnerabilities and can thus help improve the overall security of the system. See the Intel(R) 64 and IA-32 Architectures Software Developer's Manuals for more detailed information. Micro-FBGA Micro Flip Chip Ball Grid Array (G)MCH Legacy component - Graphics Memory Controller Hub. GPU Graphics Processing Unit ICH The legacy I/O Controller Hub component that contains the main PCI interface, LPC interface, USB2, Serial ATA, and other I/O functions. It communicates with the legacy (G)MCH over a proprietary interconnect called DMI. IMC Intel Integrated Memory Controller (R) 64 Technology 64-bit memory extensions to the IA-32 architecture. LCD Liquid Crystal Display LVDS Low Voltage Differential Signaling A high speed, low power data transmission standard used for display connections to LCD panels. 12 NCTF Non-Critical to Function: NCTF locations are typically redundant ground or non-critical reserved, so the loss of the solder joint continuity at end of life conditions will not affect the overall product functionality. Processor Core The term "processor core" refers to Silicon die itself which may contain single or multiple execution cores. Rank A unit of DRAM corresponding four to eight devices in parallel, ignoring ECC. These devices are usually, but not always, mounted on a single side of a SO-DIMM. SCI System Control Interrupt. Used in ACPI protocol. TDP Thermal Design Power TOM Top of Memory TTM Time-To-Market VCC Processor core power supply Datasheet Introduction (Sheet 3 of 3) Term 1.7 Description VSS Processor ground VCCGFX Graphics core power supply VCCSM DDR2/DDR3 power rail References Please refer to the following documents which may be beneficial when reading this document or for additional information: Document Document Number Intel(R) 64 and IA-32 Architectures Software Developer's Manuals Volume 1: Basic Architecture Volume 2A: Instruction Set Reference, A-M Volume 2B: Instruction Set Reference, N-Z Volume 3A: System Programming Guide http:// www.intel.com/ products/processor/ manuals/index.htm Volume 3B: System Programming Guide AP-485, Intel(R) Processor Identification and CPUID Instruction Application Note Datasheet 241618 Intel(R) AtomTM Processor N400 Series Datasheet - Volume 2 322848 Intel(R) AtomTM Processor N400 Series Specification Update 322849 Intel(R) NM10 Express Chipset Datasheet 322896 13 Introduction 1.8 System Block Diagram Figure 1-1. Platform Block Diagram VGA SystemMemory Analog Display Intel(R)AtomTM Processor N400/ N500 Series DDR2/3 DDR2/ DDR3 CH A LVDS DDR2/ : 667 MT/s DDR3 D MI USB 2. 0 8 Ports Power Management GPIO Clock Generation SATA 2 Ports Intel(R)High Definition Audio CODECs SPI Flash Firmware SMBus 2.0 Intel(R)NM10 Express Chipset LCI LAN WLAN SPI Other Devices PCIe Bus LPC/FWH PCI Bus PCI Devices EC 14 Datasheet Signal Description 2 Signal Description This chapter describes the processor signals. They are arranged in functional groups according to their associated interface or category. The following notations are used to describe the signal type. Table 2-1. Signal Types Notations Signal Type I Input Pin O Output Pin I/O Bi-directional Input/Output Pin The signal description also includes the type of buffer used for the particular signal. Table 2-2. Signal Description Buffer Types Signal Datasheet Description CMOS CMOS buffers. 1.05-V tolerant DMI Direct Media Interface signals. These signals are compatible with PCI Express* 1.0 signalling environment AC specifications but are DC coupled. The buffers are not 3.3-V tolerant. HVCMOS High Voltage buffers. 3.3-V tolerant DDR2/DDR3 DDR2/DDR3 buffers: 1.8-V/1.5-V tolerant respectively TAP Test Access Port signal Analog Analog reference or output. May be used as a threshold voltage or for buffer compensation Ref Voltage reference signal GTL+ Gunning Transceiver Logic signaling technology. Refer to GTL+ I/O Specification for complete details. Asynch This signal is asynchronous and has no timing relationship with any reference clock. LVDS Low Voltage Differential Signalling. A high speed, low power data transmission standard used for display connections to LCD panels. SSTL - 1.8/ 1.5 Stub Series Termination Logic. These are 1.8-V (DDR2) or 1.5-V (DDR3) output capable buffers. 1.8-V or 1.5-V tolerant. 15 Signal Description 2.1 Processor Legacy Signals Table 2-3. Processor Legacy Signals Signal Name A20M# BSEL[2:0] CPUPWRGOOD Description Direction If A20M# (Address-20 Mask) is asserted, the processor masks physical address bit-20 (A20#) before looking up a line in any internal cache and before driving a read/write transaction on the bus. Asserting A20M# emulates the 8086 processor's address wrap-around at the 1-MB boundary. Assertion of A20M# is only supported in real mode. I BSEL[2:0] (Bus Select) are used to select the processor input clock frequency. O CPUPWRGOOD (Power Good) is a processor input. The processor requires this signal to be a clean indication that the clocks and power supplies are stable and within their specifications. `Clean' implies that the signal will remain low (capable of sinking leakage current), without glitches, from the time that the power supplies are turned on until they come within specification. The signal must then transition monotonically to a high state. CPUPWRGOOD can be driven inactive at any time, but clocks and power must again be stable before a subsequent rising edge of CPUPWRGOOD. It must also meet the minimum pulse width specification. I Type Core CMOS Core CMOS Core CMOS The CPUPWRGOOD signal must be supplied to the processor; it is used to protect internal circuits against voltage sequencing issues. It should be driven high throughout boundary scan operation. DPRSTP# DPSLP# EXTBGREF DPRSTP#, when asserted on the platform causes the processor to transition from the Deep Sleep State to the Deeper Sleep state. In order to return to the Deep Sleep State, DPRSTP# must be deasserted. DPRSTP# is driven by the chipset. I DPRSLP#, when asserted on the platform causes the processor to transition from the Sleep State to the Deep Sleep state. In order to return to the Sleep State, DPSLP# must be deasserted. DPRSTP# is driven by the chipset. I External Bandgap Reference. I Core CMOS Core CMOS Core Analog 16 Datasheet Signal Description Table 2-3. Processor Legacy Signals Signal Name FERR# Description Direction FERR# (Floating-point Error) is a multiplexed signal and its meaning is qualified with STPCLK#. When STPCLK# is not asserted, FERR# indicates a floating point when the processor detects an unmasked floating-point error. FERR# is similar to the ERROR# signal on the Intel 387 coprocessor, and is included for compatibility with systems using MSDOS*- type floating-point error reporting. When STPCLK# is asserted, an assertion of FERR# indicates that the processor has a pending break event waiting for service. The assertion of FERR# indicates that the processor should be returned to the Normal state. When FERR# is asserted, indicating a break event, it will remain asserted until STPCLK# is deasserted. Assertion of PREQ# when STPCLK# is active will also cause an FERR# break event. O Type Core Open Drain For additional information on the pending break event functionality, including identification of support of the feature and enable/disable information, refer to Volume 3 of the Intel(R) 64 and IA-32 Architectures Software Developer's Manuals and the Intel(R) Processor Identification and CPUID Instruction Application Note. GTLREF Reference voltage for BPM* pins. I Core Analog IGNNE# INIT# Datasheet IGNNE# (Ignore Numeric Error) is asserted to force the processor to ignore a numeric error and continue to execute non-control floating-point instructions. If IGNNE# is deasserted, the processor generates an exception on a non-control floating-point instruction if a previous floating-point instruction caused an error. IGNNE# has no effect when the NE bit in control register 0 (CR0) is set. I INIT# (Initialization), when asserted, resets integer registers inside the processor without affecting its internal caches or floating-point registers. The processor then begins execution at the power-on Reset vector configured during power-on configuration. The processor continues to handle snoop requests during INIT# assertion. I Core CMOS Core CMOS 17 Signal Description Table 2-3. Processor Legacy Signals Signal Name LINT0, LINT1 Description Direction LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins of all APIC Bus agents. When the APIC is disabled, the LINT0 signal becomes INTR, a maskable interrupt request signal, and LINT1 becomes NMI, a non-maskable interrupt. INTR and NMI are backward compatible with the signals of those names on the Pentium processor. I Type Core CMOS Both of these signals must be software configured via BIOS programming of the APIC register space to be used either as NMI/INTR or LINT0/LINT1. Because the APIC is enabled by default after Reset, operation of these pins as LINT0/LINT1 is the default configuration. SMI# STPCLK# THERMDA_1 SMI# (System Management Interrupt) is asserted asynchronously by system logic. On accepting a System Management Interrupt, the processor saves the current state and enter System Management Mode (SMM). An SMI Acknowledge transaction is issued, and the processor begins program execution from the SMM handler. If SMI# is asserted during the deassertion of RESET# the processor will tristate its outputs. I Stop clock, when asserted, causes the processor to enter a low power Stop-Grant state. The processor issues a Stop-Grant Acknowledge transaction, and stops providing internal clock signals to all processor core units. The processor continues to snoop bus transactions and service interrupts while in StopGrant state. When STPCLK# is deasserted, the processor restarts its internal clock to all units and resumes execution. I Thermal Diode - Anode & Cathode of the processor. THERMDC_1 THERMDA_2/RSVD Reserved pins of Thermal Diode. THERMDC_2/RSVD BPM_1#[3:0] BPM_2#[3:0]/ RSVD Breakpoint and Performance Monitor Signals: Output from the processor that indicate the status of breakpoints and programmable counters used for monitoring processor performance. Core CMOS Core CMOS I Core O Analog I Core O Analog I/O GTL+ BPM_2#[3:0]/RSVD are reserved pins. 18 PRDY# PRDY# is a processor output used by debug tools to determine processor debug readiness. O Asynch GTL+ PREQ# PREQ# is used by debug tools to request debug operation of the processor. I Asynch GTL+ Datasheet Signal Description 2.2 System Memory Interface Table 2-4. System Memory Interface Signal Name Description Direction Type DDR_A_CK_[1:0] SDRAM Differential Clock: SDRAM Differential clock signal pair. O SSTL-1.8 DDR_A_CK#_[1:0] SDRAM Inverted Differential Clock: SDRAM Differential clock signal-pair complement. O SSTL-1.8 DDR_A_CK_[4:3] SDRAM Differential Clock: SDRAM Differential clock signal pair. O SSTL-1.8 DDR_A_CK#_[4:3] SDRAM Inverted Differential Clock: SDRAM Differential clock signal-pair complement. O SSTL-1.8 DDR_A_CS#_[3:0] Chip Select: (1 per Rank) used to select particular SDRAM components during the active state. O SSTL-1.8 O SSTL-1.8 There is one Chip Select for each SDRAM rank. DDR_A_CKE_[3:0] Clock Enable: (1 per Rank) used to: * Initialize the SDRAM during power-up * Power-down SDRAM ranks * Place all SDRAM ranks into and out of selfrefresh during STR DDR_A_MA_[14:0] Multiplexed Address: These signals are used to provide the multiplexed row and column address to the SDRAM. O SSTL-1.8 DDR_A_BS_[2:0] Bank Select: These signals define which banks are selected within each SDRAM rank. O SSTL-1.8 DDR_A_RAS# RAS Control Signal: Used with DDR_A_CAS# and DDR_A_WE# O SSTL-1.8 O SSTL-1.8 O SSTL-1.8 I/O SSTL-1.8 (along with DDR_A_CS#) to define the SDRAM commands. DDR_A_CAS# CAS Control Signal: Used with DDR_A_RAS# and DDR_A_WE# (along with DDR_A_CS#) to define the SDRAM commands. Datasheet DDR_A_WE# Write Enable Control Signal: Used with DDR_A_RAS# and DDR_A_CAS# (along with DDR_A_CS#) to define the SDRAM commands. DDR_A_DQ_[63:0] Data Bus: Channel data signal interface to the SDRAM data bus 19 Signal Description Table 2-4. System Memory Interface Signal Name DDR_A_DM_[7:0] Description Direction Type Data Mask: These signals are used to mask individual bytes of data in the case of a partial write, and to interrupt burst writes. O SSTL-1.8 When activated during writes, the corresponding data groups in the SDRAM are masked. There is one DDR_A_DM_[7:0] for every data byte lane. DDR_A_DQS_[7:0] Data Strobes: DDR_A_DQS_[7:0] and its complement signal group make up a differential strobe pair. The data is captured at the crossing point of DDR_A_DQS_[7:0] and its DDR_A_DQS#_[7:0] during read and write transactions. I/O SSTL-1.8 DDR_A_DQS#_[7:0] Data Strobe Complements: These are the complementary strobe signals. I/O SSTL-1.8 DDR_A_ODT_[3:0] On-Die-Termination: Active Termination Control O SSTL-1.8 Table 2-5. Memory Reference and Compensation Signal Name Direction Type System Memory RCOMP signal. I/O Analog DDR_RPU System Memory RCOMP signal. I/O Analog DDR_VREF SDRAM Reference Voltage I Analog DDR_RPD 2.3 Description Reset and Miscellaneous Signals Table 2-6. Reset and Miscellaneous Signals (Sheet 1 of 2) Signal Name RSTIN# Description Direction Type Reset In: When asserted, this signal will asynchronously reset the CPU logic. The signal is connected to the PLTRST# output of the south bridge. I HVCMOS I HVCMOS This input should have a Schmitt trigger to avoid spurious resets. This signal is required to be 3.3-V tolerant. PWROK Power OK: When asserted, PWROK is an indication to the processor that core power has been stable. This input should have a Schmitt trigger to avoid spurious resets. This signal is required to be 3.3V tolerant. 20 Datasheet Signal Description Table 2-6. Reset and Miscellaneous Signals (Sheet 2 of 2) Signal Name 2.4 Description Direction Type PM_EXTTS[1:0]# External Thermal Sensor Input: If the system temperature reaches a dangerously high value then this signal can be used to trigger the start of system memory throttling. EXTTS1# can alternately be used to implement fast C4/C4E exit. See Section 5.3 for details. This functionality is not available on EXTTS0#. I HVCMOS DDR3_DRAM_PWR OK DDR3 Power Good Monitor. Driven by platform logic for DDR3. Reserved pin for DDR2 design. I CMOS1.5 DDR3_DRAMRST# DDR3 DRAM Reset. Reset signal from IMC to DRAM devices; one for all SO-DIMMs. Used only in DDR3 mode; reserved pin for DDR2 design. O SSTL1.5 RSVD Reserved. Must be left unconnected on the board. Intel does not recommend a test point on the board for this ball. N/A N/A RSVD_NCTF Reserved/non-critical to function. Pin for package mechanical reliability. A test point may be placed on the board for this ball. N/A N/A RSVD_TP Reserved-test-point. A test point may be placed on the board for this ball. N/A N/A XDP_RSVD_[17:0] Reserved XDP debug signals. Connect to XDP connector; or just left as Not-Connected except for XDP_RSVD_9 - pull this pin to low for normal operation. N/A N/A DMI - Direct Media Interface Table 2-7. DMI - Processor to Chipset Serial Interface Signal Name Datasheet Description Direction Type DMI_RXP[1:0] DMI_RXN[1:0] DMI input from south bridge: Direct Media Interface receive differential pair. I DMI DMI_TXP[1:0] DMI_TXN[1:0] DMI output to south bridge: Direct Media Interface transmit differential pair. O DMI EXP_ICOMPI PCI-Express-G Input Current Compensation. Connect to EXP_RCOMPO and then to Ground via one 50 Ohm serial resistor. I Analog EXP_RCOMPO PCI-Express-G Resistance Compensation. Connect to EXP_ICOMPI and then to Ground via one 50 Ohm serial resistor. I/O Analog EXP_RBIAS PCI-Express CML Bias control: Connect to a 750 Ohm resistor to ground. I/O Analog 21 Signal Description 2.5 PLL Signals Table 2-8. PLL Signals Signal Name Description Direction Type BCLKP[0] BCLKN[0] Differential Core Clock In I Diff Clk CMOS HPL_CLKINP Differential Host Clock In I Diff Clk CMOS Differential DMI Clock In I Diff Clk CMOS Differential PLL Clock In I Diff Clk CMOS Differential Spread Spectrum Clock In I Diff Clk CMOS HPL_CLKINN EXP_CLKINP EXP_CLKINN REFCLKINN REFCLKINP REFSSCLKINN REFSSCLKINP 2.6 Analog Display Signals Table 2-9. Analog Display Signals Signal Name 22 Description Direction Type CRT_RED RED Analog Video Output: This signal is a CRT analog video output from the internal color palette DAC. O Analog CRT_GREEN GREEN Analog Video Output: This signal is a CRT analog video output from the internal color palette DAC. O Analog CRT_BLUE BLUE Analog Video Output: This signal is a CRT analog video output from the internal color palette DAC. O Analog CRT_IRTN Current return path. Shorted to ground O Analog DAC_IREF Resistor Set: Set point resistor for the internal color palette DAC. A 665-Ohm 1% resistor is required between DAC_IREF and motherboard ground. I/O Analog CRT_HSYNC CRT Horizontal Synchronization: This signal is used as the vertical sync (polarity is programmable) or "sync interval". 3.3-V output. O HVCMOS CRT_VSYNC CRT Vertical Synchronization: This signal is used as the vertical sync (polarity is programmable). 3.3V output. O HVCMOS CRT_DDC_CLK CRT DDC Clock for monitor control I/O COD CRT_DDC_DATA CRT DDC Data for monitor control I/O COD Datasheet Signal Description 2.7 LVDS Signals Table 2-10.LVDS Signals Signal Name Description Direction Type O LVDS LA_DATAP_[2:0] Differential data output - positive LA_DATAN_[2:0] Differential data output - negative O LVDS LA_CLKP Differential clock output - positive O LVDS LA_CLKN Differential clock output - negative O LVDS LIBG LVDS Reference Current. Need 2.37-KOhm pulldown resistor I/O Ref LVBG Reserved. No connect. O Analog LVREFH Reserved. Can be connected to VSS or left as No Connect. I Ref LVREFL Reserved. Can be connected to VSS or left as No Connect. I Ref LVDD_EN LVDS Panel Power Enable: Panel power control enable control. O HVCMOS LBKLT_EN LVDS Backlight Enable: Panel backlight enable control. O HVCMOS LBKLT_CTL Panel Backlight Brightness Control: Panel brightness control. O HVCMOS The accuracy of the PWM duty cycle of LBKLT_CTL signal for any given value will be within 20 ns. 2.8 LCTLA_CLK I2C based control signal (Clock) for External SSC clock chip control - optional I/O COD LCTLB_DATA I2C based control signal (Data) for External SSC clock chip control - optional I/O COD LDDC_CLK EDID support for flat panel display I/O COD LDDC_DATA EDID support for flat panel display I/O COD Description Direction Type TCK (Test Clock) provides the clock input for the processor Test Bus (also known as the Test Access Port). I TAP TDI (Test Data In) transfers serial test data into the processor. TDI provides the serial input needed for JTAG specification support. I TAP Signals Table 2-11.TAP Signals (Sheet 1 of 2) Signal Name TCK TDI Datasheet OD TAP OD 23 Signal Description Table 2-11.TAP Signals (Sheet 2 of 2) TDO TMS TRST# 2.9 TDO (Test Data Out) transfers serial test data out of the processor. TDO provides the serial output needed for JTAG specification support. O TMS (Test Mode Select) is a JTAG specification support signal used by debug tools. I TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST# must be driven low during power on Reset. I TAP OD TAP OD TAP OD Error and Thermal Protection Table 2-12.Error and Thermal Protection Signal Name PROCHOT# Description Processor Hot#: This will go active when the processor temperature monitoring sensor(s) detects that the processor has reached its maximum safe operation temperature Direction Type I/O I: CMOS O: OD Output: This indicates that the processor Thermal Control Circuit (TCC) has been activated, if enabled. Input: This signal can also be driven to the processor to activate the TCC. THERMTRIP# 2.10 Thermal Trip: The processor protects itself from catastrophic overheating by use of an internal thermal sensor. This sensor is set well above the normal operating temperature to ensure that there are no false trips. The processor will stop all execution when the junction temperature exceeds approximately 125C. This is signaled to the system by the THERMTRIP# pin. O Open Drain Processor Core Power Signals Table 2-13.Processor Core Power Signals Signal Name 24 Description Direction Type VCC Processor-core power supply. The voltage supplied to these pins is determined by the VID pins. PWR VCC_SENSE VCC_SENSE and VSS_SENSE provide an isolated, low impedance connection to the processor core voltage and ground. They can be used to sense or measure voltage near the silicon. Analog Datasheet Signal Description Table 2-13.Processor Core Power Signals 2.11 VID[6:0] VID[6:0] (Voltage ID) are used to support automatic selection of power supply voltages (VCC). I/O VSS_SENSE VCC_SENSE and VSS_SENSE provide an isolated, low impedance connection to the processor core voltage and ground. They can be used to sense or measure voltage near the silicon. VCCA Processor PLL power supply. CMOS Analog PWR Graphics, DMI and Memory Core Power Signals Table 2-14.Power Signals Signal Name 2.12 Description Voltage Level (V) Type VCCP LGI power supply 1.05 PWR VCCGFX Graphics core power supply 0.89 PWR VCCSM DDR2/DDR3 power supply 1.8/ 1.5 PWR VCCA_DMI DMI power supply 1.05 PWR VCCACRTDAC CRT DAC power supply 1.8 PWR VCC_GIO Graphics I/O power supply 3.3 PWR VCC_LGI LGIO VID power supply 1.05 PWR VCCA_DDR DDR2 power supply 1.05 PWR VCCD_HMPLL HMPLL power supply 1.05 PWR VCCDLVDS LVDS power supply 1.8 PWR VCCSFR_DMIHMPLL DMI, HPLL, MPLL power supply 1.8 PWR VCCACK_DDR DDR2 power supply 1.05 PWR VCCD_AB_DPL DPLL power supply 1.05 PWR VCCSFR_AB_DPL DPLL power supply 1.8 PWR VCCRING_EAST GIO, LVDS power supply 1.05 PWR VCCRING_WEST LGIO power supply 1.05 PWR VCCCK_DDR DDR2/DDR3 clock power supply 1.8/1.5 PWR Ground Table 2-15.Ground Signal Name VSS Description VSS are the ground pins for the processor and should be connected to the system ground plane. Direction Type GND Datasheet 25 Functional Description 3 Functional Description 3.1 Integrated Memory Controller The integrated memory controller supports DDR2 or DDR3 protocols with one 64 bit wide channel accessing two SO-DIMMs. The controller supports a maximum of two unbuffered, non-ECC DDR2 or DDR3 SO-DIMMs; thus allowing up to four device ranks. 3.1.1 System Memory Organization Modes The integrated memory controller supports only one memory organization mode: single channel. In this mode, all memory cycles are directed to a single channel. 3.1.2 System Memory Technology Supported 3.1.2.1 DDR2 Memory The system memory controller supports the following DDR2 Data Transfer Rates, SODIMM Modules and DRAM Device Technologies: * DDR2 Data Transfer Rate: 667MT/s (PC2-5300) * DDR2 SO-DIMM Modules (unbuffered, non-ECC): -- Raw Card A = 2 Ranks of x16 SDRAMs (Double-sided) -- Raw Card C = 1 Rank of x16 SDRAMs (Single-sided) "Single sided" above is a logical term referring to the number of Chip Selects attached to the SO-DIMM. A real SO-DIMM may put the components on both sides of the substrate, but be logically indistinguishable from single sided SO-DIMM if all components on the SO-DIMM are attached to the same Chip Select signal. Note: x16 means that each SDRAM component has 16 data lines. * DDR2 DRAM Device Technology: -- Standard 512Mb, 1Gb and 2Gb technologies and addressing are supported for x16 devices. There is no support for SO-DIMMs with different technologies or capacities on opposite sides of the same SO-DIMM. If one side of a SO-DIMM is populated, the other side is either identical or empty. 26 Datasheet Functional Description Table 3-16.Supported SO-DIMM Module Configurations 3.1.2.2 Raw Card Type DIMM Capacity DRAM Device Tech. DRAM Organization # of DRAM Devices # of Ranks Page Size A 512MB 512Mb 32M x 16 8 2 8K A 1GB 1Gb 64M x16 8 2 8K C 256MB 512Mb 32M x 16 4 1 8K C 512MB 1Gb 64M x 16 4 1 8K C 1GB 2Gb 128M x 16 4 1 8K DDR3 Memory The system memory controller supports the following DDR3 Data Transfer Rates, SO-DIMM Modules and DRAM Device Technologies: * DDR3 Data Transfer Rate: 667MT/s * DDR3 SO-DIMM Modules (unbuffered, non-ECC): -- Raw Card A = 2 Ranks of x16 SDRAMs (Double-sided) -- Raw Card B = 1 Rank of x8 SDRAMs (Double-sided) NOTE: x16/x8 means that each SDRAM component has 16/8 data lines. * DDR3 DRAM Device Technology: -- Standard 1Gb and 2Gb technologies and addressing are supported for x16/x8 devices. There is no support for SO-DIMMs with different technologies or capacities on opposite sides of the same SO-DIMM. If one side of a SO-DIMM is populated, the other side is either identical or empty. Table 3-17.Supported DDR3 S0-DIMM module Configurations 3.1.3 Raw Card Type DIMM Capacity DRAM Device Tech. A 1GB 1Gb 64M x 16 8 2 8K A 2GB 2Gb 128M x16 8 2 8K B 1GB 1Gb 128M x 8 8 1 8K B 2GB 2Gb 256M x 8 8 1 8K DRAM Organization # of DRAM Devices # of Ranks Page Size Rules for populating SO-DIMM slots The frequency of system memory will be the lowest frequency of all SO-DIMMs in the system, as determined through the SPD registers on the SO-DIMMs. Timing parameters [CAS latency (or CL + AL for DDR2), tRAS, tRCD, tRP] must be programmed to match within a channel. Datasheet 27 Functional Description To take advantage of enhanced addressing, it should be populating both SO-DIMM slots with the identical Raw Card type. If one SO-DIMM is used only, it should be populating the second slot (the further slot to the processor's Integrated Memory Controller) to get the best signal quality. 3.1.4 Intel(R) Fast Memory Access (Intel(R) FMA) Technology Enhancements The following sections outline and explain the technology enhancements: Just-in-Time Command Scheduling, Command Overlap, Out-of-Order Scheduling and Opportunistic Writes. 3.1.4.1 Just-in-Time Command Scheduling The memory controller has an advanced command scheduler where all pending requests are examined simultaneously to determine the most efficient request to be issued next. The most efficient request is picked from all pending requests and issued to system memory Just-in-Time to make optimal use of Command Overlapping. Thus, instead of having all memory access requests go individually through an arbitration mechanism forcing requests to be executed one at a time, they can be started without interfering with the current request allowing for concurrent issuing of requests. This allows for optimized bandwidth and reduced latency while maintaining appropriate command spacing to meet system memory protocol. 3.1.4.2 Command Overlap Command Overlap allows the insertion of the DRAM commands between the Activate, Precharge, and Read/Write commands normally used, as long as the inserted commands do not affect the currently executing command. Multiple commands can be issued in an overlapping manner, increasing the efficiency of system memory protocol. 3.1.4.3 Out-of-Order Scheduling While leveraging the Just-in-Time Scheduling and Command Overlap enhancements, the IMC continuously monitors pending requests to system memory for the best use of bandwidth and reduction of latency. If there are multiple requests to the same open page, these requests would be launched in a back to back manner to make optimum use of the open memory page. This ability to reorder requests on the fly allows the IMC to further reduce latency and increase bandwidth efficiency. 3.1.4.4 Opportunistic Writes Processor requests for memory reads usually are weighted more heavily than writes to memory to avoid cases of starving the processor of data to process while the writes are issued to system memory. Instead of having writes issued to a pending queue to be flushed to memory when certain watermarks are reached, which could starve the processor of data while it waits for the write flush to finish, the IMC monitors system memory requests and issues pending write requests to memory at times when they will 28 Datasheet Functional Description not impact memory read requests. This allows for an almost continuous flow of data to the processor for processing. 3.1.5 DRAM Clock Generation Every supported SO-DIMM has two differential clock pairs. There are total of four clock pairs driven directly by the processor to two SO-DIMMs. 3.2 Integrated Graphics Controller This section details the integrated graphics engines (3D, 2D and video), 3D pipeline, and the respective capabilities. The processor's graphics processing unit (GPU) contains several types of components. The major components in the GPU are the engines, planes, pipes and ports. The GPU has a 3D/2D instruction processing unit to control the 3D and 2D engines respectively. The processor's 3D and 2D engines are fed with data through the memory controller. The outputs of the engines are surfaces sent to the memory, which are then retrieved and processed by the processor planes. 3.2.1 3D Graphics Pipeline This GPU runs the graphics engine at 200 MHz and has two pixel pipelines. The 3D graphics pipeline has a deep pipeline architecture in which each stage can simultaneously operate on different primitives or on different portions of the same primitive. The 3D graphics pipeline is broken up into four major stages: geometry processing, setup (vertex processing), texture application and rasterization. The graphics is optimized by using the processor for advance software based transform and lighting (geometry processing) as defined by Microsoft DirectX*. The other three stages of 3D processing are handled on the GPU. The setup stage is responsible for vertex processing - converting vertices to pixels. The texture application stage applies textures to pixels. The rasterization engine takes textured pixels and applies lighting and other environment affects to produce the final pixel value. From the rasterization stage, the final pixel value is written to the frame buffer in memory so it can be displayed. 3.2.1.1 3D Engine The 3D engine on the GPU has been designed with a deep pipeline architecture, where performance is maximized by allowing each stage of the pipeline to simultaneously operate on different primitive or portions of the same primitive. The GPU supports Perspective-Correct Texture Mapping, Multitextures, Bump-Mapping, Cubic Environment Maps, Bilinear, Trilinear and Anisotropic MIP mapped filtering, Gouraud shading, Alpha-blending, Vertex and Per Pixel Fog and Z/W Buffering. Datasheet 29 Functional Description The 3D pipeline subsystem performs the 3D rendering acceleration. The main blocks of the pipeline are the setup engine, scan converter, texture pipeline, and raster pipeline. A typical programming sequence would be to send instructions to set the state of the pipeline followed by rending instructions containing 3D primitive vertex data. The engines' performance is dependent on the memory bandwidth available. Systems that have more bandwidth available will outperform systems with less bandwidth. The engines' performance is also dependent on the core clock frequency. The higher the frequency, the more data is processed. 3.2.1.2 Texture Engine The GPU allows an image, pattern, or video to be placed on the surface of the 3D polygon. The texture processor receives the texture coordinate information from the setup engine and the texture blend information from the scan converter. The texture processor performs texture color or ChromaKey matching, texture filtering (anisotropic, trilinear, bilinear interoplation), and YUV-to-RGB conversions. 3.2.2 Video Engine The Video Engine handles the non-3D (media/video) applications. It includes support for VLD and MPEG2 decode in Hardware. The CGPU engine includes a number of encompassments over the previous generation capabilities, which have been listed above. 3.2.2.1 Hardware Motion Compensation The Motion Compensation (MC) process consists of reconstructing a new picture by predicting (either forward, backward or bidirectionally) the resulting pixel colors from one or more reference pictures. The GPU receives the video stream and implements Motion Compensation and subsequent steps in hardware. Performing Motion Compensation in hardware reduces the processor demand of software-based MPEG-2 decoding, and thus improves system performance. The Motion Compensation functionality is overloaded onto the texture cache and texture filter. The texture cache is used to typically access the data in the reconstruction of the frames and the filter is used in the actual motion compensation process. To support this overloaded functionality the texture cache additionally supports the following input format: YUV420 planar. 3.2.2.2 Sub-Picture Support Sub-picture is used for two purposes, one is subtitles for movie captions, etc. (which are superimposed on a main picture), and "menus" used to provide some visual operation environments the user of a content player. DVD allows movie subtitles to be recorded as Sub-pictures. On a DVD disc, it is called "subtitle" because it has been prepared for storing captions. Since the disc can have a maximum of 32 tracks for subtitles, they can be used for various applications, for example, as subtitles in different languages or other information to be displayed. 30 Datasheet Functional Description There are two kinds of Menus, the System Menus and other In-Title Menus. First, the System Menus are displayed and operated at startup of or during the playback of the disc or from the stop state. Second, In-Title menus can be programmed as a combination of Sub-picture and Highlight commands to be displayed during playback of the disc. The GMCH supports sub-picture for DVD and DBS by mixing the two video streams via alpha blending. Unlike color keying, alpha blending provides a softer effect and each pixel that is displayed is a composite between the two video stream pixels. The GPU can utilize four methods when dealing with sub-pictures. The flexibility enables the GPU to work with all sub-picture formats. 3.2.3 2D Engine 3.2.3.1 VGA Registers The 2D registers are a combination of registers defined for the original Video Graphics Array (VGA) and others that Intel has added to support graphics modes that have color depths, resolutions, and hardware acceleration features that go beyond the original VGA standard. 3.2.3.2 Logical 128-Bit Fixed BLT and 256 Fill Engine Use of this BLT engine accelerates the Graphical User Interface (GUI) of Microsoft Windows* operating systems. The 128-bit BLT Engine provides hardware acceleration of block transfers of pixel data for many common Windows operations. The term BLT refers to a block transfer of pixel data between memory locations. The BLT engine can be used for the following: * Move rectangular blocks of data between memory locations * Data Alignment * Perform logical operations (raster ops) The rectangular block of data does not change as it is transferred between memory locations. The allowable memory transfers are between: cacheable system memory and frame buffer memory, frame buffer memory and frame buffer memory, and within system memory. Data to be transferred can consist of regions of memory, patterns, or solid color fills. A pattern will always be 8x8 pixels wide and may be 8, 16, or 32 bits per pixel. The BLT engine has the ability to expand monochrome data into a color depth of 8, 16, or 32 bits. BLTs can be either opaque or transparent. Opaque transfers move the data specified to the destination. Transparent transfers compare destination color to source color and write according to the mode of transparency selected. Datasheet 31 Functional Description Data is horizontally and vertically aligned at the destination. If the destination for the BLT overlaps with the source memory location, the graphics controller can specify which area in memory to begin the BLT transfer. Hardware is included for all 256 raster operations (Source, Pattern, and Destination) defined by Microsoft, including transparent BLT. The graphics controller has instructions to invoke BLT and stretch BLT operations, permitting software to set up instruction buffers and use batch processing. The graphics controller can perform hardware clipping during BLTs. 3.2.4 Display Pipes The display consists of two pipes: * Display Pipe A (VGA) * Display Pipe B (VGA or LVDS) A pipe consists of a set of combined planes and a timing generator. The timing generators provide the basic timing information for each of the display pipes. The GPU has two display pipes, allowing for support of two independent display streams. A port is the destination for the result of the pipe. 3.2.4.1 Clock Generator Units (DPLLs) The clock generator units provide a stable frequency for driving display devices. It operates by converting an input reference frequency into an output frequency. The timing generators take their input from internal DPLL devices that are programmable to generate pixel clocks in the range of 20 MHz-200 MHz. Accuracy for VESA timing modes is required to be within 0.5%. The DPLL can take a reference frequency from the external reference inputs (REFCLKINN/P, REFSSCLKINN/P). 3.2.5 Display Ports Display ports are the destination for the display pipes. These are the places where the data finally appears to devices outside the graphics device. the GPU has one CRT display port (Analog) and one dedicated LVDS port (Digital). 3.2.5.1 Analog Display Port Characteristics The analog display port provides a RGB signal output along with a HSYNC and VSYNC signal. There is an associated DDC signal pair that is implemented using GPIO pins dedicated to the analog port. The intended target device is for a CRT based monitor with a VGA connector. Display devices such as LCD panels with analog inputs may work satisfactory but no functionality added to the signals to enhance that capability. 32 Datasheet Functional Description Table 3-18.Analog Port Characteristics Signal RGB Port Characteristics Support Voltage Range 0.7 Vp-p only Monitor Sense Analog Compare Analog Copy Protection No Sync on Green No Voltage 3.3V Enable/Disable Port control HSYNC Polarity Adjust VGA or port control VSYNC Composite Sync Support No Special Flat Panel Sync No Stereo Sync No Voltage External buffered to 5V Control Through GPIO interface DDC 3.2.5.1.1 Integrated RAMDAC The display function contains a RAM-based Digital-to-Analog Converter (RAMDAC) that transforms the digital data from the graphics and video subsystems to analog data for the CRT monitor. GPU's integrated RAMDAC supports resolutions up to 1400 x 1050 @ 60 Hz. Three 8-bit DACs provide the R, G, and B signals to the monitor. 3.2.5.1.2 Sync Signals HSYNC and VSYNC signals are digital and conform to TTL signal levels at the connector. These signals can be polarity adjusted and individually disabled in one of the two possible states. The sync signals should power up disabled in the high state. No composite sync or special flat panel sync support will be included. 3.2.5.2 Single Channel LVDS Port The processor has an integrated single channel LVDS (Low Voltage Differential Signaling) port that supports 1x18 data format. There is one LVDS transmitter channel in the LVDS port; this channel consists of 3 data pairs and a clock pair. The channel supports transmit clock frequency ranges from 25 MHz to 112 MHz which provides a throughput of up to 784Mbps on each data output and up to 112 MP/s on the input. 3.2.5.2.1 LVDS Data Pairs and Clock Pairs The LVDS data and clock pairs are identical buffers and differ only in the use defined for that pair. The LVDS data pair is used to transfer pixel data as well as the LCD timing control signals. A single clock pair is used to transfer clocking information to the LVDS receiver. A serial pattern of 1100011 represents one cycle of the clock. Datasheet 33 Functional Description There is one LVDS transmitter channel in the LVDS interface. It contains 1-clock pair and 3-data pair of low voltage differential swing signals. Figure 3-2 shows a pair of LVDS signals and swing voltage. Figure 3-2. LVDS Signals and Swing Voltage 1's and 0's are represented the differential voltage between the pair of signals. Figure 3-3. LVDS Clock and Data Relationship 3.2.5.2.2 LVDS Pair States The LVDS pairs can be put into one of five states, powered down tri-state, powered down 0 V, common mode, send 0's, or active. When in powered down state, the circuit enters a low power state and drives out 0 V or tri-states on both the output pins for the entire channel. The common mode tri-state is both pins of the pair set to the common mode voltage. When in the send 0's state, the circuit is powered up but sends only 0 for the pixel color data regardless what the actual data is with the clock lines and timing signals sending the normal clock and timing data. 34 Datasheet Functional Description 3.2.5.2.3 Panel Power Sequencing This section provides details for the power sequence timing relationship of the panel power, the backlight enable and the LVDS data timing delivery. In order to meet the panel power timing specification requirements, two signals, LVDD_EN and BKLT_EN are provided to control the timing sequencing function of the panel and the backlight power supplies. Panel Power Sequence States A defined power sequence is recommended when enabling the panel or disabling the panel. The set of timing parameters can vary from panel to panel vendor, provided that they stay within a predefined range of values. The panel VDD power, the backlight on/ off state and the LVDS clock and data lines are all managed by an internal power sequencer. A requested power-up sequence is only allowed to begin after the power cycle delay time requirement T4 is met. Figure 3-4. Panel Power Sequencing T4 T1+T2 T5 TX T3 T4 Panel On Panel VDD Enable Panel BackLight Enable Off Off Valid Clock/Data Lines Power On Sequence from off state and Power Off Sequence after full On Table 3-19. Panel Power Sequencing Timing Parameters Panel Power Sequence Timing Parameters Spec Name Datasheet From To Min Max Name Units 0 10 T1 ms 50 T2 ms T5 ms Vdd On 0.1 Vdd 0.9 Vdd LVDS Active Vdd Stable On LVDS Active 0 Backlight LVDS Active Backlight on 200 Backlight State Backlight Off LVDS off X X TX ms LVDS State LVDS Off Start power off 0 50 T3 ms Power cycle Delay Power Off Power On Sequence Start 0 400 T4 ms 35 Functional Description 3.2.6 VESA/VGA Mode VESA/VGA mode provides compatibility for pre-existing software that set the display mode using the VGA CRTC registers. Timings are generated based on the VGA register values and the timing generator registers are not used. 3.2.6.1 DDC (Display Data Channel) DDC is a standard defined by VESA. Its purpose is to allow communication between the host system and display. Both configuration and control information can be exchanged allowing plug-and-play systems to be realized. Support for DDC 1 and DDC 2 is implemented. The GPU uses the CRT_DDC_CLK and CRT_DDC_DATA signals to communicate with the analog monitor. The GPU will generate these signals at 3.3V. External pull-up resistors and level shifting circuitry should be implemented on the board. The GPU implements a hardware GMBus controller that can be used to control these signals allowing for transactions speeds up to 100 kHz. 3.2.7 Multiple Display Configurations Since the GPU has two display ports available for its two pipes, it can support up to two different images on different display devices. The GPU integrated in this processor supports two display modes: Dual Display Clone and Extended Desktop (LVDS + VGA). 3.3 Thermal Sensor There are several registers that need to be configured to support the uncore thermal sensor functionality and SMI# generation. Customers must enable the Catastrophic Trip Point as protection for the processor. If the Catastrophic Trip Point is crossed, then the processor will instantly turn off all clocks inside the device. Customers may optionally enable the Hot Trip Point to generate SMI#. Customers will be required to then write their own SMI# handler in BIOS that will speed up the processor (or system) fan to cool the part. 3.3.1 PCI Device 0, Function 0 The SMICMD register requires that a bit be set to generate an SMI# when the Hot Trip point is crossed. The ERRSTS register can be inspected for the SMI alert. Address 36 Register Symbol Register Name Default Value Access C8-C9 ERRST Error Status 0000h RWC/S, RO CC-CDh SMICMD SMI Command 0000h RO, R/W Datasheet Functional Description 3.4 Power Management The processor has many permutations of possibly concurrently operating modes. Care should be taken (Hardware and Software) to disable unused sections of the silicon when this can be done with sufficiently low performance impact. Refer to Chapter 5 and the ACPI Specification, Rev3.0 for more details. 3.5 Intel(R) Hyper-Threading Technology The processor supports Intel(R) Hyper-Threading Technology (Intel(R) HT Technology), which allows an execution core to function as two logical processors. While some execution resources such as caches, execution units, and buses are shared, each logical processor has its own architectural state with its own set of general-purpose registers and control registers. This feature must be enabled via the BIOS and requires operating system support. Intel recommends enabling Hyper-Threading Technology with Microsoft Windows Vista*, Microsoft Windows* XP Professional/Windows* XP Home, and disabling HyperThreading Technology via the BIOS for all previous versions of Windows operating systems. For more information on Hyper-Threading Technology, see http:// www.intel.com/products/ht/hyperthreading_more.htm. Datasheet 37 Electrical Specifications 4 Electrical Specifications This chapter contains signal group descriptions, absolute maximum ratings, voltage identification and power sequencing. The chapter also includes DC specifications. Please note that all data or specifications for processors supporting DDR3 and/or Dual core processors in this chapter are based on pre-silicon estimates and simulations or empirical data; these specifications will be updated with characterized data from silicon measurements at a later date. 4.1 Power and Ground Balls The processor has VCC and VSS (ground) inputs for on-chip power distribution. All power balls must be connected to their respective processor power planes, while all VSS balls must be connected to the system ground plane. Use of multiple power and ground planes is recommended to reduce I*R drop. The VCC balls must be supplied with the voltage determined by the processor Voltage IDentification (VID) signals. 4.2 Decoupling Guidelines Due to large number of transistors and high internal clock speeds, the processor is capable of generating large current swings between low- and full-power states. This may cause voltages on power planes to sag below their minimum values, if bulk decoupling is not adequate. Larger bulk storage (CBULK), such as electrolytic capacitors, supply current during longer lasting changes in current demand (for example, coming out of an idle condition). Similarly, capacitors act as a storage well for current when entering an idle condition from a running condition. To keep voltages within specification, output decoupling must be properly designed. Caution: 4.2.1 Design the board to ensure that the voltage provided to the processor remains within the specifications. Failure to do so can result in timing violations or reduced lifetime of the processor. Voltage Rail Decoupling The voltage regulator solution needs to provide: * Bulk capacitance with low effective series resistance (ESR). * A low path impedance from the regulator to the processor. * Bulk decoupling to compensate for large current swings generated during poweron, or low-power idle state entry/exit. The power delivery solution must ensure that the voltage and current specifications are met, as defined in Table 4-23. 38 Datasheet Electrical Specifications 4.3 Processor Clocking BCLKP, BCLKN, HPL_CLKINP, HPL_CLKINN, EXP_CLKINP, EXP_CLKINN, REFCLKINP, REFCLKINN The processor utilizes differential clocks to generate the processor core(s) and memory controller frequency, and other internal clocks. The processor core frequency is determined by multiplying the processor core ratio by 166MHz. Clock multiplying within the processor is provided by an internal phase locked loop (PLL), which requires a constant frequency input, with exceptions for Spread Spectrum Clocking (SSC). 4.3.1 PLL Power Supply An on-die PLL filter solution is implemented on the processor. Refer to Table 4-23 for DC specifications. 4.4 Voltage Identification (VID) The processor uses seven voltage identification signals, VID[6:0], to support automatic selection of voltages. Table 4-20 specifies the voltage level corresponding to the state of VID[6:0]. A `1' in this table refers to a high voltage level and a `0' refers to a low voltage level. If the processor is not soldered on board (VID[6:0] = 1111111), or the voltage regulation circuit cannot supply the voltage that is requested, the voltage regulator must disable itself. VID signals are CMOS push/pull drivers. Refer to Table 4-25 for the DC specifications for these signals. Individual processor VID values may be set during manufacturing so that two devices at the same core frequency may have different VID settings. The VR utilized must be capable of regulating its output to the value defined by the VID values issued. DC specifications are included in Table 4-25 and Table 4-26. Table 4-20.Voltage Identification Definition Datasheet VID6 VID5 VID4 VID3 VID2 VID1 VID0 VCC (V) 0 0 1 1 0 0 0 1.2000 0 0 1 1 0 0 1 1.1875 0 0 1 1 0 1 0 1.1750 0 0 1 1 0 1 1 1.1625 0 0 1 1 1 0 0 1.1500 0 0 1 1 1 0 1 1.1375 0 0 1 1 1 1 0 1.1250 0 0 1 1 1 1 1 1.1125 0 1 0 0 0 0 0 1.1000 0 1 0 0 0 0 1 1.0875 0 1 0 0 0 1 0 1.0750 0 1 0 0 0 1 1 1.0625 39 Electrical Specifications Table 4-20.Voltage Identification Definition 40 VID6 VID5 VID4 VID3 VID2 VID1 VID0 VCC (V) 0 1 0 0 1 0 0 1.0500 0 1 0 0 1 0 1 1.0375 0 1 0 0 1 1 0 1.0250 0 1 0 0 1 1 1 1.0125 0 1 0 1 0 0 0 1.0000 0 1 0 1 0 0 1 0.9875 0 1 0 1 0 1 0 0.9750 0 1 0 1 0 1 1 0.9625 0 1 0 1 1 0 0 0.9500 0 1 0 1 1 0 1 0.9375 0 1 0 1 1 1 0 0.9250 0 1 0 1 1 1 1 0.9125 0 1 1 0 0 0 0 0.9000 0 1 1 0 0 0 1 0.8875 0 1 1 0 0 1 0 0.8750 0 1 1 0 0 1 1 0.8625 0 1 1 0 1 0 0 0.8500 0 1 1 0 1 0 1 0.8375 0 1 1 0 1 1 0 0.8250 0 1 1 0 1 1 1 0.8125 0 1 1 1 0 0 0 0.8000 0 1 1 1 0 0 1 0.7875 0 1 1 1 0 1 0 0.7750 0 1 1 1 0 1 1 0.7625 0 1 1 1 1 0 0 0.7500 0 1 1 1 1 0 1 0.7375 0 1 1 1 1 1 0 0.7250 0 1 1 1 1 1 1 0.7125 1 0 0 0 0 0 0 0.7000 Datasheet Electrical Specifications 4.5 Catastrophic Thermal Protection The processor supports the THERMTRIP# signal for catastrophic thermal protection. An external thermal sensor should also be used to protect the processor and the system against excessive temperatures. Even with the activation of THERMTRIP#, which halts all processor internal clocks and activity, leakage current can be high enough such that the processor cannot be protected in all conditions without the removal of power to the processor. If the external thermal sensor detects a catastrophic processor temperature of 125C (maximum), or if the THERMTRIP# signal is asserted, the VCC supply to the processor must be turned off within 500 ms to prevent permanent silicon damage due to thermal runaway of the processor. THERMTRIP# functionality is not ensured if the PWRGOOD signal is not asserted. 4.6 Reserved or Unused Signals The following are the general types of reserved (RSVD) signals and connection guidelines: * RSVD - these signals should not be connected * RSVD_TP - these signals should be routed to a test point * RSVD_NCTF - these signals are non-critical to function and may be left unconnected Arbitrary connection of these signals to VCC*, VSS*, or to any other signal (including each other) may result in component malfunction. See Chapter 5 for a land listing of the processor and the location of all reserved signals. For reliable operation, always connect unused inputs or bi-directional signals to an appropriate signal level. Unused active high inputs should be connected through a resistor to ground (VSS). Unused outputs maybe left unconnected; however, this may interfere with some Test Access Port (TAP) functions, complicate debug probing, and prevent boundary scan testing. A resistor must be used when tying bi-directional signals to power or ground. When tying any signal to power or ground, a resistor will also allow for system testability. Resistor values should be within 20% of the impedance of the baseboard trace. 4.7 Signal Groups Signals are grouped by buffer type and similar characteristics as listed in Chapter 2. The buffer type indicates which signaling technology and specifications apply to the signals. All the differential signals, and selected DDR2 and Control Sideband signals have On-Die Termination (ODT) resistors. There are some signals that do not have ODT and need to be terminated on the board. All Control Sideband Asynchronous signals are required to be asserted/deasserted for at least eight BCLKs in order for the processor to recognize the proper signal state. See Section 4.10 for the DC and AC specifications. Datasheet 41 Electrical Specifications 4.8 Test Access Port (TAP) Connection Due to the voltage levels supported by other components in the Test Access Port (TAP) logic, Intel recommends the processor be first in the TAP chain, followed by any other components within the system. A translation buffer should be used to connect to the rest of the chain unless one of the other components is capable of accepting an input of the appropriate voltage. Two copies of each signal may be required with each driving a different voltage level. 4.9 Absolute Maximum and Minimum Ratings Table 4-21 specifies absolute maximum and minimum ratings. At conditions outside functional operation condition limits, but within absolute maximum and minimum ratings, neither functionality nor long-term reliability can be expected. If a device is returned to conditions within functional operation limits after having been subjected to conditions outside these limits (but within the absolute maximum and minimum ratings) the device may be functional, but with its lifetime degraded depending on exposure to conditions exceeding the functional operation condition limits. Although the processor contains protective circuitry to resist damage from ElectroStatic Discharge (ESD), precautions should always be taken to avoid high static voltages or electric fields Table 4-21.Processor Absolute Minimum and Maximum Ratings (Sheet 1 of 2) Symbol 42 Parameter Min Max Unit Notes1, 2 6 VCC, VCCP Processor Core, LGI voltages with respect to VSS -0.3 1.45 V VCCSM, VCCCK_DDR Processor DDR voltage with respect to VSS -0.3 2.25 V VCCA Processor PLL voltage with respect to VSS -0.3 2.25 V VCCGFX Processor GFX voltage with respect to VSS -0.3 1.55 V VCCLVDS Processor LVDS voltage with respect to VSS -0.3 2.25 V VCCA_DDR, VCCACK_DDR Processor DDR PLL voltage with respect to VSS -0.3 1.45 V VCCRING_EAST, VCCRING_WEST, VCC_LGI_VID, Processor DAC, LGIO, LVDS, & LGIO voltage with respect to VSS -0.3 1.45 V VCCD_AB_DPL, VCCD_HMPLL Processor DPLL, & HMPLL voltage with respect to VSS -0.3 1.45 V VCCSFR_AB_DPL, Processor SFR DPLL voltage with respect to VSS -0.3 2.25 V VCCACRTDAC Processor CRT DAC voltage with respect to VSS -0.3 2.25 V Datasheet Electrical Specifications Table 4-21.Processor Absolute Minimum and Maximum Ratings (Sheet 2 of 2) Symbol Parameter Min Max Unit VCCSFR_DMIHMPLL Processor DMI SFR voltage with respect to VSS -0.3 2.25 V VCC_GIO Processor GIO voltage with respect to VSS 3.135 3.465 V TSTORAGE Storage temperature -40 85 C VinLGIO LGIO Buffer DC Input Voltage with Respect to VSS, -0.1 1.45 V VinAsynch_CMOS CMOS Buffer DC Input Voltage with Respect to VSS -0.1 1.45 V Notes1, 2 3, 4, 5 NOTES: 1. For functional operation, all processor electrical, signal quality, mechanical and thermal specifications must be satisfied. 2. Excessive overshoot or undershoot on any signal will likely result in permanent damage to the processor. 3. Storage temperature is applicable to storage conditions only. In this scenario, the processor must not receive a clock, and no lands can be connected to a voltage bias. Storage within these limits will not affect the long-term reliability of the device. For functional operation, please refer to the processor case temperature specifications. 4. This rating applies to the processor and does not include any tray or packaging. 5. Failure to adhere to this specification can affect the long-term reliability of the processor. 6. VCC is a VID based rail. Possible damage to the processor may occur if the processor temperature exceeds 150 C. Intel does not ensure functionality for parts that have exceeded temperature above 150 C due to specification violation. 4.10 DC Specifications Section 4.10 lists the DC specifications for the processor and are valid only while meeting the thermal specifications, clock frequency, and input voltages. 4.10.1 Voltage and Current Specifications Table 4-23 and Table 4-23 list the DC specifications for the processor core and I/O buffer; they are valid only while meeting specifications for junction temperature, clock frequency, and input voltages. The Highest Frequency Mode (HFM) and Lowest Frequency Mode (LFM) refer to the highest and lowest core operating frequencies supported on the processor. Active mode load line specifications apply in all states except in the Deeper Sleep state. VCC,BOOT is the default voltage driven by the voltage regulator at power up in order to set the VID values. Unless specified otherwise, all specifications for the processor are at TJ = 100C. Care should be taken to read all notes associated with each parameter. Datasheet 43 Electrical Specifications Table 4-22.Processor Core Active and Idle Mode DC Voltage and Current Specifications Symbol Unit 0.8 1.175 V VCC at Highest Frequency Mode 0.9625 1.175 V 2, 3 VCC at Lowest Frequency Mode 0.8 0.95 V 2, 3 VCCDPRSLP VCC at Deeper Sleep (C4) 0.8 0.95 V VCC,BOOT Default VCC voltage for initial power up 1.26 V ICC ICC for processor core VCC_HFM VCC_LFM VID Range ISGNT IDPRSLP SLOPELL Typ (HFM) (LFM) -- -- -- -- IAH Min Note1 Max VID Parameter 1.045 1.20 5.77 6.04 11.54 11.54 N450/N455 N470/N475 N550 N570 A ICC Auto-Halt -- N400 series 3.06 -- N500 series 6.12 A ICC Stop-Grant -- N400 series 3.03 -- N500 series 6.06 ICC Deeper Sleep (C4) A -- N400 series 2.04 -- N500 series 4.08 Processor Core Supply Loadline A -5.9 m Figure 45 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. Each processor is programmed with voltage identification value (VID), which is set at manufacturing and cannot be altered. Individual VID values are calibrated during manufacturing such that two processors at the same frequency may have different settings within the VID range. Please note this differs from the VID employed by the processor during a power management event. 3. The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-M minimum impedance. The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not coupled in the scope probe. 44 Datasheet Electrical Specifications Figure 4-5. VCC and ICC Processor Loadline VCC [V] Slope = -5.9mV/A at package VCC_SENSE, VSS_SENSE pins. Differential Remote Sense required. VCC max VCC, DC max 10mV= RIPPLE VCC nom VCC, DC min VCC min VCC Tolerance = [VID*1.5%] 0 ICC [A] ICC max The I/O buffer supply voltage should be measured at the processor package pins. The tolerances shown in Table 4-23 are inclusive of all noise from DC up to 20 MHz. The voltage rails should be measured with a bandwidth limited oscilloscope with a roll-off of 3 dB/decade above 20 MHz under all operating conditions. Table 4-23 indicates which supplies are connected directly to a voltage regulator or to a filtered voltage rail. For voltage rails that are connected to a filter, they should be measured at the input of the filter. If the recommended platform decoupling guidelines cannot be met, the system designer will have to make trade-offs between the voltage regulator out DC tolerance and the decoupling performances of the capacitor network to stay within the voltage tolerances listed below. Datasheet 45 Electrical Specifications Table 4-23.Processor I/O Buffer Supply DC Voltage and Current Specifications Symbol Parameter Min Typ Max Unit VCCA Processor Core analog supply voltage (DC + AC specification) 1.425 1.5 1.575 V ICCA Processor Core analog supply current 0.080 A VCCGFX GFX supply voltage 0.8455 0.89 0.9345 V ICCGFX GFX supply current 2.64 A VCCALVDS, VCCDLVDS, LVDS supply voltage 1.89 V VCCACRTDAC CRT DAC supply voltage ICCALVDS, ICCDLVDS, LVDS and CRT DAC supply current 0.15 A 1.89 V 0.18 A 1.71 1.8 Note ICCACRTDAC VCCSFR_DMIHMPLL, VCCSFR_AB_DPL ICCSFR_DMIHMPLL, ICCSFR_AB_DPL VCCSM, VCCCK_DDR DMIHMPLL supply voltage and Display PLL supply voltage 1.71 1.8 DMIHMPLL supply current and Display PLL supply current DDR I/O supply voltage and DDR Clock power supply voltage V DDR2 1.71 1.8 1.89 DDR3 1.425 1.5 1.575 ICCSM, DDR I/O supply current (DDR2/DDR3) 2.00 A ICCCK_DDR DDR Clock power supply current (DDR2/ DDR3) 0.27 A VCCA_DMI, DMI analog supply voltage and PLL supply voltage 1.1025 V 0.54 A 1.1025 V 0.06 A 1.1025 V VCCD_HMPLL ICCA_DMI, ICCD_HMPLL VCCD_AB_DPL, VCC_LGI ICCD_AB_DPL, ICC_LGI 1.05 DMI analog supply current and PLL supply current Display PLL supply voltage and LGI supply voltage 0.9975 1.05 Display PLL supply current and LGI supply current VCCA_DDR, VCCACK_DDR DDR analog supply voltage ICCA_DDR, ICCACK_DDR DDR analog supply current 0.9975 1.05 A DDR2 1.32 DDR3 1.882 VCCP Legacy I/O supply voltage ICCP Legacy I/O supply current VCCRING_EAST, VCCRING_WEST DAC, GIO, LVDS supply voltage and LGIO supply voltage 46 0.9975 0.9975 0.9975 1.05 1.05 1.1025 V 0.42 A 1.1025 V Datasheet Electrical Specifications Table 4-23.Processor I/O Buffer Supply DC Voltage and Current Specifications Symbol Parameter Min ICCRING_EAST, ICCRING_WEST DAC, GIO, LVDS supply voltage and LGIO supply current VCC_GIO GIO supply voltage ICC_GIO GIO supply current 4.10.2 3.135 Typ 3.3 Max Unit 0.19 A 3.465 V 0.01 A Note Interface DC Specifications Platform reference voltages at the top of Table 4-23 are specified at DC only. VREF measurements should be made with respect to the supply voltage. 4.10.2.1 Input Clock DC Specification Table 4-24.Input Clocks (BCLK, HPL_CLKIN, REFCLKIN, EXP_CLKIN) Differential Specification Symbol Parameter VIL Input Low Voltage VIH Input High Voltage VCROSS Absolute crossing voltage dVCROSS Range of crossing points CIN Input Capacitance Min Typ -0.30 0 0.3 1.0 Max Units Notes1 V 1.15 V 0.550 V 0.14 V 3.0 pF 2 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. Crossing voltage defined as instantaneous voltage when rising edge of CLKN equalise CLKP. The crossing point must meet the absolute and relative crossing point specification simultaneously. 4.10.2.2 DDR2/DDR3 DC Specifications Datasheet Parameter VIL(DC) Input Low Voltage VIH(DC) Input High Voltage VIL(AC) Input Low Voltage VIH(AC) Input High Voltage Min (V) Typ (V) Max (V) Notes1 Symbol Units Table 4-25.DDR2/DDR3 Signal Group DC Specifications DDR_VREF - 0.2 V 2,4,9 DDR_VREF + 0.2 DDR_VREF - 0.25 DDR_VREF + 0.25 V 3,9 V 2,4,9 V 3,9 47 Electrical Specifications VOL Parameter Min (V) Typ (V) Max (V) Notes1 Symbol Units Table 4-25.DDR2/DDR3 Signal Group DC Specifications Output Low Voltage 5 DDR2 0.27 DDR3 0.20 Output High Voltage VOH V DDR2 1.47 DDR3 1.22 ILI Input Leakage Current VREF DDR Reference Voltage CI/O DQ/DQS/DQS# DDR2 I/O Pin Capacitance 10 4,5 A VCCSM / 2 3.5 7 3.5 3.6 pF NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. VIL is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical low value. 3. VIH is defined as the minimum voltage level at a receiving agent that will be interpreted as a logical high value. 4. VIH and VOH may experience excursions above VCCSM. However, input signal drivers must comply with the signal quality specifications. 5. Measured at VCCSM(MIN). 6. The minimum and maximum values for these signals are programmable by BIOS 7. VCCSM varies with typical/min/max cases. Refer Table 4-23 for details. 8. 2x Buffer Strength Settings is equal to a 20Ohm buffer setting. 9. DDR_VREF could either be from external or internal reference voltage. 4.10.2.3 LGIO Signal DC Specification Table 4-26.GTL Signal Group DC Specifications Symbol 48 Parameter Notes1 Min Typ Max Units 1 1.05 1.1 V 2/3 VCCP V 6 Ohm 10 VCCP I/O Voltage GTLREF GTL Reference Voltage RODT On Die Termination VIH Input High Voltage GTLREF + 0.1 VCCP + 0.1 V 3,6 VIL Input Low Voltage -0.1 GTLREF - 0.1 V 2,4 VOH Output High Voltage VCCP - 0.1 VCCP V 6 2/3 VCCP 55 Datasheet Electrical Specifications Table 4-26.GTL Signal Group DC Specifications Parameter Min Typ Max Units Notes1 RTT Termination Resistance 20 55 70 Ohm 7 RON Buffer on Resistance 14 25 40 5 ILI Input Leakage Current -100 100 A 8 CPAD Pad Capacitance 2.35 2.6 pF 9 Symbol 2.5 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. VIL is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical low value. 3. VIH is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical high value. 4. VIH and VOH may experience excursions above VCCP.. However, input signal drivers must comply with the signal quality specifications. 5. This is the pull-down driver resistance. Measured at 0.31 * VCCP. RON(min) = 0.4 * RTT, RON(typ) = 0.455 * RTT, RON(max) = 0.51 * RTT. RTT typical value of 55 Ohm is used for RON typ/min/max calculations. 6. GTLREF is the on-die termination resistance measured at VOL of the output driver. Measured at 0.31 * VCCP. The VCCP. referred to in these specifications is the instantaneous VCCP. 7. RTT is the on-die termination resistance measured at VOL of the output driver. Measured at 0.31 * VCCP. RTT is connected to VCCP on die. 8. Specified with on-die RON and RTT are turned off. Vin between 0 and VCCP. 9. CPAD includes die capacitance only. No package parasitic are included. 10. On die termination resistance, measured at 0.33 * VCCP. Table 4-27.Legacy CMOS Signal Group DC Specification Symbol VCCP Parameter I/O Voltage Min Typ Max Units 1.00 1.05 1.10 V Notes1 VIH Input High Voltage 0.7 * VCCP VCCP + 0.1 V 2 VIL Input Low Voltage -0.1 0 0.3 * VCCP V 2, 3 VOH Output High Voltage 0.9 * VCCP VCCP VCCP + 0.1 V 2, 4 VOL Output Low Voltage -0.1 0.1 * VCCP V 2, 5 ILI Input Leakage Current -100 100 uA 6 CPAD1 Pad Capacitance 2.35 2.5 2.6 pF 7 CPAD2 Pad Capacitance for CMOS Input 0.85 1.0 1.05 pF 8 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. The VCCP referred to in these specifications is the instantaneous VCCP. 3. Refer to the processor I/O Buffer Models for I/V characteristics. 4. Measured at Iout = -1.1 mA. Datasheet 49 Electrical Specifications 5. 6. 7. Measured at Iout = 1.1 mA. For VIN between 0V and VCCP. Measured when driver is tri-stated. CPAD1 includes die capacitance only for CPUPWRGOOD. No package parasitic are included. CPAD2 includes die capacitance for all other CMOS input signals. No package parasitics are included. 8. Table 4-28.Open Drain Signal Group DC Specification Symbol Parameter Min Typ Max Units Notes1 3 VOH Output High Voltage VCCP - 5% VCCP + 5% V VOL Output Low Voltage -- 0.20 V IOL Output Low Current 16 60 mA ILI Input Leakage Current 200 uA 4 2.6 pF 5 CPAD Pad Capacitance -200 1.8 2.1 2 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. Measured at 0.2V 3. VOH is determined by value of the external pull-up resistor to VCCP. 4. For VIN between 0V and VCCP. 5. CPAD includes die capacitance only. No package parasitic are included. Table 4-29.PWROK and RSTIN# DC Specification Symbol Max Units Notes1,2 -0.3 0.8 V 2 2.7 VCC3.3*(1+ 5%) V 2 Input Leakage Current 100 uA Pad Capacitance 1.5 pF Parameter Min VIL Input Low Voltage VIH Input High Voltage LI CPAD1 Typ NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. VIH may experience excursions above VCCP.. However, input signal drivers must comply with the signal quality specifications. Table 4-30.CPUPWRGOOD DC Specification Symbol Parameter Min Max Units VIL Input Low Voltage -0.1 0.3 * VCCP V VIH Input High Voltage 0.7 * VCCP VCCP + 0.1 V VHYS Hysteresis of Schmitt Trigger Inputs 100 -- mV LI Input Current of Each I/O Pin -10 10 uA CI Capacitance of Each I/O Pin -- 1.5 pF Notes1 2 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. VIH may experience excursions above VCCP.. However, input signal drivers must comply with the signal quality specifications. 50 Datasheet Electrical Specifications Table 4-31.DDR3_DRAM_PWROK DC Specification Symbol Parameter VIL Input Low Voltage VIH Input High Voltage IIL Inputs leakage current Min Max Units 0.29 V 1.25P Notes1 V 20 2 uA NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. VIH may experience excursions above VCCSM. However, input signal drivers must comply with the signal quality specifications. Datasheet 51 Electrical Specifications 4.10.2.4 JTAG DC Specification Symbol RPDGTL Parameter Min Typ GTL mode pull-down impedance (JTAG mode) Max 25 Units Ohm VT- Input fall transition threshold voltage 0.54* VCCP - 0.66* VCCP V VT+ Input rise transition threshold voltage 0.74* VCCP - 0.86* VCCP V 50 uA ILI Notes1 Table 4-32.TAP Signal Group DC Specification Input Leakage Current NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 4.10.2.5 Display DC Specification The Analog Video Signal DC Specifications are referred to the VESA Video Signal Standard Version 1, Revision 2. Table 4-33.CRT_DDC_DATA. CRT_DDC_CLK DC, LDDC_DATA, LDDC_CLK, LCTLA_CLK, and LCTLB_DATA Specification Symbol Parameter Standard mode 100 kbits/s Min Max Units VIL Input Low Voltage -0.5 0.3 VCC_GIO V VIH Input High Voltage 0.7 VCC_GIO 0.5 + VCC_GIO V Notes1 VOL1 Output Low Voltage - 1 0 0.4 V 2 LI Input Leakage Current -50 50 uA 3 CI Capacitance -- 10 pF NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. 3mA sink current. 3. 0.1 VCC_GIO < VIN < 0.9 VCC_GIO(MAX) 52 Datasheet Electrical Specifications Table 4-34.CRT_HSYNC and CRT_VSYNC DC Specification Symbol Parameter Min Typ Max Units VOH Output High Voltage 2.4 -- VCC_GIO V VOL Output Low Voltage 0 -- 0.5 V IOH Output High Current -- -- 8 mA IOL Output Low Current -- -- 8 mA Notes1 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. Table 4-35.LVDS Interface DC Specification (functional operating range, VCCLVDS = 1.8V +/- 5%) Symbol VOD VOD VOS VOS Parameter Differential Output Voltage Min Typ Max Units Notes1 250 350 450 mV 2 50 mV 2 1.375 V 2 50 mV 2 -3.5 -10 mA 2 1 10 uA 2 Change in VOD between Complementary Output States Offset Voltage 1.125 1.25 Change in VOS between Complementary Output States IOS Output Short Circuit Current IOZ Output TRI-STATE Current NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. All LVDS active lanes must be terminated with 100 Ohm resistor for correct VOS performance and measurement. Table 4-36.LVDD_EN, LBLKLT_EN and LBKLT_CTL DC Specification Symbol Parameter Min Typ Max Units Notes1 VOL Output Low Voltage 0 -- 0.4 V 2 VOH Output High Voltage VCC_GIO - 0.5 -- VCC_GIO V 2 IL Input Leakage -50 -- 50 uA 3 NOTES: 1. Unless otherwise noted, all specifications in this table apply to all processor frequencies. 2. ICL=6mA, IOH=2mA 3. For power and unpowered devices. Datasheet 53 Power Management 5 Power Management This chapter provides information on power management capabilities of the processor: * ACPI States * Processor Core States * IGD (Integrated Graphics Devices) States * IMC (Integrated Memory Controller) States * DMI (Direct Media Interface) States 5.1 ACPI States Supported The ACPI states supported by the processor are described in this section. 5.1.1 System States Table 5-37.System States State 5.1.2 Description G0/S0 Full On G1/S3-Cold Suspend-to-RAM (STR). Context saved to memory. G1/S4 Suspend-to-Disk (STD). All power lost (except wakeup on chipset) G2/S5 Soft off. All power lost (except wakeup on chipset) G3 Mechanical/hard off. All power (AC and battery) removed from system Processor Idle States Table 5-38.Processor Core/Package States Support State C0 Active mode, processor executing code C1 AutoHALT state C2 Stop Clock. Clock to processor is still running. Clock stopped to processor core C4 Deeper Sleep. Clock to processor stopped with reduced voltage on the processor C1E, C2E, C4E 54 Description Extended C-states; C1/C2/C4 states work together with Enhanced Intel(R) SpeedStep Technology Datasheet Power Management 5.1.3 Integrated Graphics Display States Table 5-39.Integrated Graphics Display Device Control State 5.1.4 Description D0 Display active D3 Display power off Integrated Memory Controller States Table 5-40.Main Memory States States 5.1.5 Description Power-up CKE asserted. Active mode Precharge Powerdown CKE de-asserted (not self-refresh) with all banks closed Active Powerdown CKE de-asserted (not self-refresh) with at least one bank active Self-Refresh CKE de-asserted using device self-refresh DMI States Table 5-41.DMI States States 5.1.6 Description L0 Full on - Active transfer state L0s First Active Power Management low power state - Low exit latency L1 Lowest Active Power Management - Longer exit latency Interface State Combinations Table 5-42.G, S and C State combinations Global (G) State Datasheet Sleep (S) State Processor Core (C) State Processor State System Clocks Description G0 S0 C0 Full On On Full On G0 S0 C1/C1E Auto-Halt On Auto-Halt G0 S0 C2/C2E Stop-Grant On Stop-Grant G0 S0 C4/C4E Deeper Sleep On Deeper Sleep G1 S3 Power off Off except RTC Suspend to RAM 55 Power Management Table 5-42.G, S and C State combinations Global (G) State Sleep (S) State G1 S4 G2 G3 Processor Core (C) State Processor State System Clocks Description Suspend to Disk Power off Power off Off except RTC S5 Power off Power off Off except RTC Soft Off NA Power Off Power off Power off Hard Off Table 5-43.D, S and C state Combinations 5.2 Graphics Adapter (D) State Sleep (S) State Package (C) State D0 S0 C0 Full On, Displaying D0 S0 C1 Auto-Halt, Displaying D0 S0 C2/C4 D3 S0 Any Not Displaying D3 S3 --- Not Displaying, host core power off. D3 S4 --- Not Displaying Suspend to disk Host core power off Description Stop Grant/Deeper Sleep, Displaying Processor Core Power Management While executing code, Enhanced Intel(R) SpeedStep Technology optimizes the processor's frequency and core voltage based on workload. Each frequency and voltage operating point is defined by ACPI as a P-state. When the processor is not executing code, it is idle. A low-power idle state is defined by ACPI as a C-state. In general, lower power C-states have longer entry and exit latencies. 5.2.1 Enhanced Intel SpeedStep(R) Technology The following are the key features of Enhanced Intel SpeedStep Technology: * Multiple frequency and voltage points for optimal performance and power efficiency. These operating points are known as P-states. * Frequency selection is software controlled by writing to processor MSRs. The voltage is optimized based on the selected frequency: -- If the target frequency is higher than the current frequency, VCC is ramped up in steps to an optimized voltage. This voltage is signaled by the VID pins to the voltage regulator. Once the voltage is established, the PLL locks on to the target frequency. -- If the target frequency is lower than the current frequency, the PLL locks to the target frequency, then transitions to a lower voltage by signaling the target voltage on the VID pins. 56 Datasheet Power Management -- Software-requested transitions are accepted at any time. If a previous transition is in progress, the new transition is deferred until the previous transition is completed. * The processor controls voltage ramp rates internally to ensure glitch-free transitions. * Because there is low transition latency between P-states, a significant number of transitions per second are possible. * Improved Thermal Monitor mode. -- When the on-die thermal sensor indicates that the die temperature is too high, the processor can automatically perform a transition to a lower frequency and voltage specified in a software programmable MSR. -- The processor waits for a fixed time period. If the die temperature is down to acceptable levels, an up transition to the previous frequency and voltage point occurs. -- An interrupt is generated for the up and down Intel Thermal Monitor transitions enabling better system level thermal management. 5.2.2 Dynamic Cache Sizing Dynamic Cache Sizing allows the processor to flush and disable a programmable number of L2 cache ways upon each Deeper Sleep entry under the following condition: * The C0 timer that tracks continuous residency in the Normal package state, has not expired. This timer is cleared during the first entry into Deeper Sleep to allow consecutive Deeper Sleep entries to shrink the L2 cache as needed. * The predefined L2 shrink threshold is triggered. The number of L2 cache ways disabled upon each Deeper Sleep entry is configured in the BBL_CR_CTL3 MSR. The C0 timer is referenced through the CLOCK_CORE_CST_CONTROL_STT MSR. The shrink threshold under which the L2 cache size is reduced is configured in the PMG_CST_CONFIG_CONTROL MSR. If the ratio is zero, then the ratio will not be taken into account for Dynamic Cache Sizing decisions. 5.2.3 Low-Power Idle States When the processor core is idle, low-power idle states (C-states) are used to save power. More power savings actions are taken for numerically higher C-states. However, higher C-states have longer exit and entry latencies. Resolution of C-states occur at the thread, processor core, and processor core package level. Thread level C-states are available if Hyper-Threading Technology is enabled. Datasheet 57 Power Management 5.2.3.1 Clock Control and Low-Power States The processor core supports low power states at the thread level and core/package level. Thread states (TCx) loosely correspond to ACPI processor core power states (Cx). A thread may independently enter TC1/AutoHALT, TC1/MWAIT, TC2, TC3 and TC4 lower power states, but this does not always cause a power state transition. Only when both threads request a low-power state (TCx) greater than the current processor core state will a transition occur. The central power management logic ensures the entire processor core enters the new common processor core power state. For processor core power states higher than C1, this would be done by initiating a P_LVLx (P_LVL2, P_LVL3, P_LVL4) I/O read to both threads. Package states are states that require external intervention and typically map back to processor core power states. Package states for processor core include Normal (C0, C1), and Stop Grant, Stop Grant Snoop (C2), and Deeper Sleep (C4). The processor core implements two software interfaces for requesting low power states: MWAIT instruction extensions with sub-state hints and P_LVLx reads to the ACPI P_BLK register block mapped in the processor core's I/O address space. The P_LVLx I/O reads are converted to equivalent MWAIT C-state requests inside the processor core and do not directly result in I/O reads on the processor core bus. The monitor address does not need to be setup before using the P_LVLx I/O read interface. The sub-state hints used for each P_LVLx read can be configured in a software programmable MSR by BIOS. If a thread encounters a chipset break even while STPCLK# is asserted, then it asserts the PBE# output signal. Assertion of PBE# (multifunction of FERR#) when STPCLK# is asserted indicates to system logic that individual threads should return to the C0 state and the processor core should return to the Normal state. Figure 5-6. Idle Power Management Breakdown of the Processor Thread Thread 0 State Thread 1 State Processor Core/Package State Entry and exit of C-states at the thread and core level are show in Figure 5-7 58 Datasheet Power Management Figure 5-7. Thread C-state Stop Grant STPCLK# asserted STPCLK# de-asserted C1/ M W AIT STPCLK# de-asserted STPCLK# de-asserted STPCLK# asserted Core state break STPCLK# asserted C1/Auto Halt HLT instruction MW AIT(C1) Halt break C0 Core State break P_LVL2 or MW AIT(C2) Core state break C2 P_LVL4 or MW AIT(C4) C4 NOTES: 1. halt break = A20M# transition, INIT#, INTR, NMI, PREQ#, SMI# or APIC interrupt. 2. core state break = (halt break OR Monitor event) AND STPCLK# high (not asserted) 3. STPCLK# assertion and de-assertion have no effect if a thread is in C2 state. Figure 5-8. Processor Core Low-power States STPCLK# asserted DPSLP# asserted Stop Grant Normal STPCLK# de-asserted DPSLP# de-asserted Snoop serviced DPRSTP# asserted Deep Sleep Deeper Sleep DPRSTP# de-asserted Snoop occurs Stop Grant Snoop Datasheet 59 Power Management Table 5-44. Coordination of Thread Low-power States at the Package/Core Level Thread 0 Processor Core C-State Thread 1 C0 C1 C2 C4 C0 C0 C0 C0 C0 C1 C0 C11 C11 C11 C2 C0 C11 C2 C2 C4 C0 C11 C2 C4 NOTES: 1. AutoHALT or MWAIT/C1 2. To enter a package state, both threads must be in a common low power state. If the threads are not in a common low power state, the package state will resolve to the highest power C state. 5.2.4 Thread C-states Description 5.2.4.1 Thread C0 State This is the normal operating state for threads in the processor core. 5.2.4.2 Thread C1/AutoHALT Powerdown State C1/AutoHALT is a low-power state entered when one thread executes the HALT instruction while the other is in the TC1 or greater thread state. The processor core will transition to the C0 state upon occurrence of SMI#, INIT#, LINT00/LINT10 (NMI, INTR), or internal bus interrupt messages. RSTINB will cause the processor core to immediately initialize itself. A System Management Interrupt (SMI) handler will return execution to either Normal state or the AutoHALT power down state. See the Intel(R) 64 and IA-32 Architectures Software Developer's Manuals, Volume 3A/3B: System Programmer's Guide for more information. The system can generate STPCLK# while the processor core is in the AutoHALT power down state. When the system de-asserts the STPCLK# interrupt, the processor core will return to the HALT state. While in AutoHalt power down state, the processor core will process bus snoops. The processor core will enter an internal snoopable sub-state to process the snoop and then return to the AutoHALT power down state. 60 Datasheet Power Management 5.2.4.3 Thread C1/MWAIT Power-down State C1/MWAIT is a low-power state entered when one thread executes the MWAIT (C1) instruction while the other thread is in the TC1 or greater thread state. processor core behavior in the MWAIT state is identical to the AutoHALT state except that Monitor events can cause the processor core to return to the C0 state. See the Intel(R) 64 and IA-32 Architectures Software Developer's Manuals, Volume 2A: Instruction Set Reference, A-M and Volume 2B: Instruction Set Reference, N-Z, for more information. 5.2.4.4 Thread C2 State Individual threads of the dual-threaded processor can enter the C2 state by initiating a P_LVL2 I/O read to the P_BLK or an MWAIT(C2) instruction, but the processor will not issue a Stop-Grant Acknowledge special bus cycle unless the STPCLK# pin is also asserted. While in the C2 state, the processor will process bus snoops and snoops from the other thread. The processor thread will enter a snoopable sub-state to process the snoop and then return to the C2 state. 5.2.4.5 Thread C4 State Individual threads of the processor can enter the C4 state by initiating a P_LVL4 I/O read to the P_BLK or an MWAIT(C4) instruction. If both processor threads are in C4, the central power management logic will request that the entire processor enter the Deeper Sleep package low-power state. To enable the package level Intel Enhanced Deeper Sleep state, Dynamic Cache Sizing and Intel Enhanced Deeper Sleep state fields must be configured in the PMG_CST_CONFIG_CONTROL MSR. 5.2.5 Processor Core/Package C-states Description The following state descriptions assume that both threads are in a common low power state. For cases when only one thread is in a low power state, no change in Core/ Package power state will occur (see Section 5.2.3). 5.2.5.1 Normal State (C0, C1) This is the normal operating state for the processor core. The processor core remains in the Normal state when the processor core is in the C0, C1/AutoHALT, or C1/MWAIT state. C0 is the active execution state. 5.2.5.2 C2 State Individual threads of the dual-threaded processor core can enter TC2 state by initiating a P_LVL2 I/O read to the P_BLK or an MWAIT (C2) instruction. Once both threads have C2 as a common state, the processor core will transition to the C2 state; however, the processor core will not issue a Stop-Grant Acknowledge special bus cycle unless the STPCLK# pin is also asserted by the chipset. Datasheet 61 Power Management While in the C2 state, the processor core will process bus snoops. The processor core will enter a snoopable sub-state described in the following section (and shown in Figure 31), to process the snoop and return to the C2 state. 5.2.5.2.1 Stop-Grant State When STPCLK# pin is asserted, each thread of the processor cores enter the StopGrant state within 1384 bus clocks after the response phase of the processor-issued Stop-Grant Acknowledge special bus cycle. When the STPCLK# pin is deasserted, the core returns to its previous low-power state. RSTIN# causes the processor core to immediately initialize itself, but the processor core will stay in Stop-Grant state. When RSTIN# is asserted by the system, the STPCLK#, DPSLP#, and DPRSTP# pins must be de-asserted prior to RSTIN# deassertion. While in Stop-Grant state, the processor core will service snoops and latch interrupts delivered on the internal bus. The processor core will latch SMI#, INIT# and LINT[1:0] interrupts and will service only one of each upon return to the Normal state. The PBE# (FERR#) signal may be driven when the processor core is in Stop-Grant state. PBE# will be asserted if there is any pending interrupt or Monitor event latched within the processor core. Pending interrupts that are blocked by the EFLAGS. IF bit being clear will still cause assertion of PBE#. Assertion of PBE# indicates to system logic that the entire processor core should return to the Normal state. A transition to the Stop-Grant Snoop state occurs when the processor core detects a snoop on the internal bus. 5.2.5.2.2 Stop-Grant Snoop State The processor core responds to snoop or interrupt transactions on the internal bus while in Stop-Grant state by entering the Stop-Grant Snoop state. The processor core will stay in this state until the snoop on the internal bus has been serviced (whether by the processor core or another agent on the internal bus) or the interrupt has been latched. The processor core returns to the Stop-Grant state once the snoop has been serviced or the interrupt has been latched. 5.2.5.3 Deep Sleep State The Deep Sleep state is entered through assertion of the DPSLP# pin while in the Sleep state. BCLK may be stopped during the Deep Sleep state for additional platform level power savings. Deep Sleep State is mapped into the Deeper Sleep State for this processor. BCLK stop/restart timings on appropriate chipset-based platforms with the clock chip are as follows: * Deep Sleep entry: the system clock chip may stop/tri-state BCLK within 2 BCLKs of DPSLP# assertion. It is permissible to leave BCLK running during Deep Sleep. 62 Datasheet Power Management * Deep Sleep exit: the system clock chip must start toggling BCLK within 10 BCLK periods within DPSLP# de-assertion. 5.2.5.4 Deeper Sleep State The Deeper Sleep state is similar to the Deep Sleep state but further reduces core voltage levels. One of the potential lower core voltage levels is achieved by entering the base Deeper Sleep state. The Deeper Sleep state is entered through assertion of the DPRSTP# pin while in the Deep Sleep state. In response to entering Deeper Sleep, the processor drives the VID code corresponding to the Deeper Sleep core voltage on the VID [6:0] pins. Exit from Deeper Sleep is initiated by DPRSTP# de-assertion when the core requests a package state other than C4 or the core requests a processor performance state other than the lowest operating point. 5.2.5.5 Extended Low-Power States Extended low-power states (C1E, C2E, C4E) optimize for power by forcibly reducing the performance state of the processor when it enters a package low-power state. Instead of directly transitioning into the package low-power state, the extended low-power state first reduces the performance state of the processor by performing an Enhanced Intel(R) SpeedStep Technology transition down to the lowest operating point. Upon receiving a break event from the package low-power state, control will be returned to software while an Enhanced Intel(R) SpeedStep Technology transition up to the initial operating point occurs. The advantage of this feature is that it significantly reduces leakage while in the package low power states. Also, long-term reliability may not be assured if the Extended Low-Power States are not enabled. The processor implements two software interfaces for requesting extended package low-power states: MWAIT instruction extensions with sub-state hints and via BIOS by configuring IA32_MISC_ENABLES MSR bits to automatically promote package lowpower states to extended package low-power states. Extended Stop-Grant and Extended Deeper Sleep must be enabled via the BIOS for the processor to remain within specification. Not complying to this guideline may affect the long-term reliability of the processor. Enhanced Intel(R) SpeedStep Technology transitions are multi-step processes that require clocked control. These transitions cannot occur when the processor is in the Sleep or Deep Sleep package low-power states since processor clocks are not active in these states. Extended Deeper Sleep is an exception to this rule when the Hard C4E configuration is enabled in the IA32_MISC_ENABLES MSR. This Extended Deeper Sleep state configuration will lower core voltage to the Deeper Sleep level while in Deeper Sleep and, upon exit, will automatically transition to the lowest operating voltage and frequency to reduce snoop service latency. Datasheet 63 Power Management The transition to the lowest operating point or back to the original software requested point may not be instantaneous. Furthermore, upon very frequent transitions between active and idle states, the transitions may lag behind the idle state entry resulting in the processor either executing for a longer time at the lowest operating point or running idle at a high operating point. Observations and analyses show this behavior should not significantly impact total power savings or performance score while providing power benefits in most other cases. 5.3 External Thermal Sensor PM_EXTTS1#: Implementation for Fast C4/C4E Exit Being used as DPRSLPVR is an alternate functionality for the PM_EXTTS1# signal. This implementation enables power savings by speeding up the C4 exit latency. To enable power savings, the PM_EXTTS1#/DPRSLPVR of the processor and the DPSLPVR signal of the chipset should be connected as shown in Figure 5-9 below. The DPRSLPVR signal of the chipset needs to be connected to the DPRSLPVR signal of the IMVP6 via a 500ohm series isolation resistor. The pull-up on the PM_EXTTS1# signal should be removed in this particular implementation. This implementation enables power-savings by increasing average C-state residency of the processor (The probability of the CPU going into C4/C4E state increases if the exit latency is reduced). With this implementation, PM_EXTTS1# cannot be used for thermal throttling of Memory. If this implementation is chosen, system designers shall need to ensure that the memory Auto-refresh rate programmed on their systems is the most appropriate for their thermal solution and choice of memory. Intel strongly recommends the implementation described above, to enable greater power savings on the processor. For details of the recommended routing topologies and guidelines, please contact your Intel Field Representative. Note: PM_EXTTS0# cannot be used in this manner. 64 Datasheet Power Management Figure 5-9. PM_EXTTS1#/DPSLPVR Implementation for Fast C4/C4E Exit Datasheet 65 Thermal Specifications and Design Considerations 6 Thermal Specifications and Design Considerations The processor requires a thermal solution to maintain temperatures within operating limits as set forth in Section Thermal Specifications. Any attempt to operate the processor outside these operating limits may result in permanent damage to the processor and potentially other components in the system. As processor technology changes, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable, long-term system operation. A complete thermal solution includes both component and system level thermal management features. Component level thermal solutions include active or passive heatsink attached to the exposed processor die. The solution should make firm contact to the die while maintaining processor mechanical specifications such as pressure. A typical system level thermal solution may consist of a system fan used to evacuate or pull air through the system. Alternatively, the processor may be in a fan-less system, but would likely still use a multi-component heat spreader. Note that trading of thermal solutions also involves trading performance. 6.1 Thermal Specifications To allow for the optimal operation and long-term reliability of Intel processor-based systems, the system/processor thermal solution should be designed such that the processor remains within the minimum and maximum junction temperature (Tj) specifications at the corresponding thermal design power (TDP) value listed in Table 645. Thermal solutions not designed to provide this level of thermal capability may affect the long-term reliability of the processor and system. The maximum junction temperature is defined by an activation of the processor Thermal Monitor. Refer to Section 6.1.2 for more details. Analysis indicates that real applications are unlikely to cause the processor to consume the theoretical maximum power dissipation for sustained time periods. Intel recommends that complete thermal solution designs target the TDP indicated in Table 6-45 instead of the maximum processor power consumption. The Intel Thermal Monitor feature is designed to help protect the processor in the unlikely event that an application exceeds the TDP recommendation for a sustained period of time. For more details on the usage of this feature, refer to Section Section 6.1.2. In all cases the Intel Thermal Monitor feature must be enabled for the processor to remain within specification. 66 Datasheet Thermal Specifications and Design Considerations Table 6-45.Power Specifications for the Processor Symbol TDP Symbol Processor Number Core Frequency Thermal Design Power N450/N455 1.66 GHz 5.5/6.5 N470/N475 1.83 GHz 6.5 N550 1.5 GHz N570 1.66 GHz 6.5 Parameter Tj Unit Notes W 1, 2, 3 6.5 Min 0 Typ Max Unit 100 (C) NOTES: 1. The TDP specification should be used to design the processor thermal solution. The TDP is not the maximum theoretical power the processor can generate. 2. Not 100% tested. These power specifications are determined by characterization of the processor currents at higher temperatures and extrapolating the values for the temperature indicated. 3. The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within specifications. The processor incorporates 3 methods of monitoring die temperature: Digital Thermal Sensor, Intel Thermal Monitor, and the Thermal Diode. The Intel Thermal Monitor (detailed in Section Section 6.1.2) must be used to determine when the maximum specified processor junction temperature has been reached. 6.1.1 Thermal Diode The processor incorporates an on-die PNP transistor whose base emitter junction is used as a thermal "diode", with its collector shorted to ground. The thermal diode can be read by an off-die analog/digital converter (a thermal sensor) located on the motherboard or a stand-alone measurement kit. The thermal diode may be used to monitor the die temperature of the processor for thermal management or instrumentation purposes but is not a reliable indication that the maximum operating temperature of the processor has been reached. See Section 6.1.2 for more details and thermal diode usage recommendation when the PROCHOT# signal is not asserted. The reading of the external thermal sensor (on the motherboard) connected to the processor thermal diode signals will not necessarily reflect the temperature of the hottest location on the die. This is due to inaccuracies in the external thermal sensor, on-die temperature gradients between the location of the thermal diode and the hottest location on the die, and time based variations in the die temperature measurement. Time based variations can occur when the sampling rate of the thermal diode (by the thermal sensor) is slower than the rate at which the TJ temperature can change. Datasheet 67 Thermal Specifications and Design Considerations Offset between the thermal diode based temperature reading and the Intel Thermal Monitor reading may be characterized using the Intel Thermal Monitor's Automatic mode activation of the thermal control circuit. This temperature offset must be taken into account when using the processor thermal diode to implement power management events. Table 6-46 and Table 6-47 provide the diode interface and specifications. Transistor model parameters shown in Table 6-47 providing more accurate temperature measurements when the diode ideality factor is closer to the maximum or minimum limits. Contact your external sensor supplier for their recommendation. The thermal diode is separate from the Thermal Monitor's thermal sensor and cannot be used to predict the behavior of the Thermal Monitor. Table 6-46.Thermal Diode Interface Signal Name Pin/Ball Number Signal Description THRMDA_1 D30 Thermal diode anode THRMDC_1 E30 Thermal diode cathode Table 6-47.Thermal Diode Parameters using Transistor Model Symbol IFW Parameter Min Typ Max Unit Notes Forward Bias Current 5 200 A 1 IE Emitter Current 5 200 A 1 nQ Transistor Ideality 0.997 Beta RT 1.001 0.25 Series Resistance 2.79 4.52 1.015 2,3,4 0.65 2,3 6.24 2,5 NOTES: 1. Intel does not support or recommend operation of the thermal diode under reverse bias. 2. Characterized across a temperature range of 50-100C. 3. Not 100% tested. Specified by design characterization. 4. The ideality factor, nQ, represents the deviation from ideal transistor model behavior as exemplified by the equation for the collector current: IC = IS * (e qVBE/nQkT -1) 5. where IS = saturation current, q = electronic charge, VBE = voltage across the transistor base emitter junction (same nodes as VD), k = Boltzmann Constant, and T = absolute temperature (Kelvin). The series resistance, RT, provided in the Diode Model Table (Table 6-47) can be used for more accurate readings as needed. When calculating a temperature based on the thermal diode measurements, a number of parameters must be either measured or assumed. Most devices measure the diode ideality and assume a series resistance and ideality trim value, although are capable of also measuring the series resistance. Calculating the temperature is then accomplished using the equations listed under Table 6-47. In most sensing devices, an expected value for the diode ideality is designed-in to the temperature calculation equation. If the designer of the temperature sensing device assumes a perfect diode, the ideality 68 Datasheet Thermal Specifications and Design Considerations value (also called ntrim) will be 1.000. Given that most diodes are not perfect, the designers usually select an ntrim value that more closely matches the behavior of the diodes in the processor. If the processor diode ideality deviates from that of the ntrim, each calculated temperature will be offset by a fixed amount. This temperature offset can be calculated with the equation: Terror(nf) = Tmeasured * (1 - nactual/ntrim) where Terror(nf) is the offset in degrees C, Tmeasured is in Kelvin, nactual is the measured ideality of the diode, and ntrim is the diode ideality assumed by the temperature sensing device. 6.1.2 Intel(R) Thermal Monitor The Intel Thermal Monitor helps control the processor temperature by activating the TCC (Thermal Control Circuit) when the processor silicon reaches its maximum operating temperature. The temperature at which the Intel Thermal Monitor activates the TCC is not user configurable. Bus traffic is snooped in the normal manner and interrupt requests are latched (and serviced during the time that the clocks are on) while the TCC is active. With a properly designed and characterized thermal solution, it is anticipated that the TCC would only be activated for very short periods of time when running the most power intensive applications. The processor performance impact due to these brief periods of TCC activation is expected to be minor and hence not detectable. An underdesigned thermal solution that is not able to prevent excessive activation of the TCC in the anticipated ambient environment may cause a noticeable performance loss and may affect the long-term reliability of the processor. In addition, a thermal solution that is significantly under designed may not be capable of cooling the processor even when the TCC is active continuously. The Intel Thermal Monitor controls the processor temperature by modulating (starting and stopping) the processor core clocks when the processor silicon reaches its maximum operating temperature. The Intel Thermal Monitor uses two modes to activate the TCC: automatic mode and on-demand mode. If both modes are activated, automatic mode takes precedence. There are two automatic modes called Intel Thermal Monitor-1 and Intel Thermal Monitor-2. These modes are selected by writing values to the MSRs of the processor. After automatic mode is enabled, the TCC will activate only when the internal die temperature reaches the maximum allowed value for operation. The Intel Thermal Monitor automatic mode must be enabled through BIOS for the processor to be operating within specifications. Intel recommends TM1 and TM2 be enabled on the processors. When TM1 is enabled and a high temperature situation exists, the clocks will be modulated by alternately turning the clocks off and on at a 50% duty cycle. Cycle times are processor speed dependent and will decrease linearly as processor core frequencies increase. Once the temperature has returned to a non-critical level, modulation ceases Datasheet 69 Thermal Specifications and Design Considerations and TCC goes inactive. A small amount of hysteresis has been included to prevent rapid active/inactive transitions of the TCC when the processor temperature is near the trip point. The duty cycle is factory configured and cannot be modified. Also, automatic mode does not require any additional hardware, software drivers, or interrupt handling routines. Processor performance will be decreased by the same amount as the duty cycle when the TCC is active. When Intel Thermal Monitor-2 is enabled and a high temperature situation exists, the processor will perform an Enhanced Intel(R) SpeedStep Technology transition to the LFM. When the processor temperature drops below the critical level, the processor will make an Enhanced Intel(R) SpeedStep Technology transition to the last requested operating point. Intel Thermal Monitor-1 and Intel Thermal Monitor-2 can co-exist within the processor. If both Intel Thermal Monitor-1 and Intel Thermal Monitor-2 bits are enabled in the auto-throttle MSR, Intel Thermal Monitor-2 will take precedence over Intel Thermal Monitor-1. However, if Force Intel Thermal Monitor-1 over Intel Thermal Monitor-2 is enabled in MSRs via BIOS and Intel Thermal Monitor-2 is not sufficient to cool the processor below the maximum operating temperature, then Intel Thermal Monitor-1 will also activate to help cool down the processor. If a processor load based Enhanced Intel(R) SpeedStep Technology transition (through MSR write) is initiated when a Intel Thermal Monitor-2 period is active, there are two possible results: * If the processor load based Enhanced Intel(R) SpeedStep technology transition target frequency is higher than the Intel Thermal Monitor-2 transition based target frequency, the processor load-based transition will be deferred until the Intel Thermal Monitor-2 event has been completed. * If the processor load-based Enhanced Intel(R) SpeedStep technology transition target frequency is lower than the Intel Thermal Monitor-2 transition based target frequency, the processor will transition to the processor load-based Enhanced Intel(R) SpeedStep technology target frequency point. The TCC may also be activated via on-demand mode. If bit 4 of the ACPI Intel Thermal Monitor control register is written to a 1, the TCC will be activated immediately independent of the processor temperature. When using on-demand mode to activate the TCC, the duty cycle of the clock modulation is programmable via bits 3:1 of the same ACPI Intel Thermal Monitor control register. In automatic mode, the duty cycle is fixed at 50% on, 50% off, however in on-demand mode, the duty cycle can be programmed from 12.5% on/ 87.5% off, to 87.5% on/12.5% off in 12.5% increments. On-demand mode may be used at the same time automatic mode is enabled, however, if the system tries to enable the TCC via on-demand mode at the same time automatic mode is enabled and a high temperature condition exists, automatic mode will take precedence. An external signal, PROCHOT# (processor hot) is asserted when the processor detects that its temperature is above the thermal trip point. Bus snooping and interrupt latching are also active while the TCC is active. 70 Datasheet Thermal Specifications and Design Considerations Besides the thermal sensor and thermal control circuit, the Intel Thermal Monitor also includes one ACPI register, one performance counter register, three MSR, and one I/O pin (PROCHOT#). All are available to monitor and control the state of the Intel Thermal Monitor feature. The Intel Thermal Monitor can be configured to generate an interrupt upon the assertion or deassertion of PROCHOT#. PROCHOT# will not be asserted when the processor is in the low power states like Stop Grant and Deeper Sleep; hence, the thermal diode reading must be used as a safeguard to maintain the processor junction temperature within maximum specification. If the platform thermal solution is not able to maintain the processor junction temperature within the maximum specification, the system must initiate an orderly shutdown to prevent damage. If the processor enters one of the above power states with PROCHOT# already asserted, PROCHOT# will remain asserted until the processor exits the low power state and the processor junction temperature drops below the thermal trip point. If Intel Thermal Monitor automatic mode is disabled, the processor will be operating out of specification. Regardless of enabling the automatic or on-demand modes, in the event of a catastrophic cooling failure, the processor will automatically shut down when the silicon has reached a temperature of approximately 125C. At this point the THERMTRIP# signal will go active. THERMTRIP# activation is independent of processor activity and does not generate any bus cycles. When THERMTRIP# is asserted, the processor core voltage must be shut down within the time specified. 6.1.3 Digital Thermal Sensor The processor also contains an on die Digital Thermal Sensor (DTS) that can be read via an MSR (no I/O interface). The DTS is only valid while the processor is in the normal operating state (the Normal package level low power state). Unlike traditional thermal devices, the DTS will output a temperature relative to the maximum supported operating temperature of the processor (TJ_max). It is the responsibility of software to convert the relative temperature to an absolute temperature. The temperature returned by the DTS will always be at or below TJ_max. Catastrophic temperature conditions are detectable via an Out Of Spec status bit. This bit is also part of the DTS MSR. When this bit is set, the processor is operating out of specification and immediate shutdown of the system should occur. The processor operation and code execution is not ensured once the activation of the Out of Spec status bit is set. The DTS-relative temperature readout corresponds to the Thermal Monitor 1(TM1) and Thermal Monitor 2 (TM2) trigger points. When the DTS indicates maximum processor core temperature has been reached, the TM1 or TM2 hardware thermal control mechanism will activate. The DTS and TM1/TM2 temperature may not correspond to the thermal diode reading since the thermal diode is located in a separate portion of the die and thermal gradient between the DTS. Additionally, the thermal gradient from DTS to thermal diode can vary substantially due to changes in processor power, Datasheet 71 Thermal Specifications and Design Considerations mechanical and thermal attach, and software application. The system designer is required to use the DTS to ensure proper operation of the processor within its temperature operating specifications. Changes to the temperature can be detected via two programmable thresholds located in the processor MSRs. These thresholds have the capability of generating interrupts via the core's local APIC. Refer to the Intel(R) 64 and IA-32 Architectures Software Developer's Manuals for specific register and programming details. 6.1.4 Out of Specification Detection Overheat detection is performed by monitoring the processor temperature and temperature gradient. This feature is intended for graceful shut down before the THERMTRIP# is activated. If the processor's TM1 is triggered and the temperature remains high, an "Out Of Spec" status and sticky bit are latched in the status MSR register and generates thermal interrupt. 6.1.5 PROCHOT# Signal Pin An external signal, PROCHOT# (processor hot), is asserted when the processor die temperature has reached its maximum operating temperature. If TM1 is enabled, then the TCC will be active when PROCHOT# is asserted. The processor can be configured to generate an interrupt upon the assertion or deassertion of PROCHOT#. The processor implements a bi-directional PROCHOT# capability to allow system designs to protect various components from overheating situations. The PROCHOT# signal is bi-directional in that it can either signal when the processor has reached its maximum operating temperature or be driven from an external source to activate the TCC. The ability to activate the TCC via PROCHOT# can provide a means for thermal protection of system components. Only a single PROCHOT# pin exists at a package level of the processor. When the core's thermal sensor trips, PROCHOT# signal will be driven by the processor package. If TM1 is enabled, PROCHOT# will be asserted and only the core that is above TCC temperature trip point will have its core clock modulated. If TM2 is enabled and the core is above TCC temperature trip point, it will enter the lowest programmed TM2 performance state. It is important to note that Intel recommends both TM1 and TM2 to be enabled. When PROCHOT# is driven by an external agent and if only TM1 is enabled on the core, then the processor core will have the clocks modulated. If TM2 is enabled, then the processor core will enter the lowest programmed Intel Thermal Monitor-2 performance state. It should be noted that Force TM1 on TM2, enabled via BIOS, does not have any effect on external PROCHOT#. If PROCHOT# is driven by an external agent when TM1, TM2, and Force TM1 on TM2 are all enabled, then the processor will still apply only TM2. 72 Datasheet Thermal Specifications and Design Considerations PROCHOT# may be used for thermal protection of voltage regulators (VR). System designers can create a circuit to monitor the VR temperature and activate the TCC when the temperature limit of the VR is reached. By asserting PROCHOT# (pulled-low) and activating the TCC, the VR will cool down as a result of reduced processor power consumption. Bi-directional PROCHOT# can allow VR thermal designs to target maximum sustained current instead of maximum current. Systems should still provide proper cooling for the VR and rely on bi-directional PROCHOT# only as a backup in case of system cooling failure. The system thermal design should allow the power delivery circuitry to operate within its temperature specification even while the processor is operating at its TDP. With a properly designed and characterized thermal solution, it is anticipated that bi-directional PROCHOT# would only be asserted for very short periods of time when running the most power intensive applications. An under-designed thermal solution that is not able to prevent excessive assertion of PROCHOT# in the anticipated ambient environment may cause a noticeable performance loss. Datasheet 73 Package Mechanical Specifications and Ball Information 7 Package Mechanical Specifications and Ball Information This chapter provides the package specifications, and ballout assignments. 7.1 Package Mechanical Specifications The processor is available with 559 pins micro-FCBGA8 package. The package dimensions are shown in Figure 7-10. 7.1.1 Package Mechanical Drawings Figure 7-10.Package Mechanical Drawings 74 Datasheet Package Mechanical Specifications and Ball Information 7.1.2 Package Loading Specifications Package loading is 15lb max static compressive. 7.2 Processor Ballout Assignment Figure 7-10 to Figure 7-14 are graphic representations of the processor ballout assignments. Table 7-48 lists the ballout by signal name. Figure 7-11.Package Pinmap (Top View, Upper-Left Quadrant) 1 2 A --- --- 3 B --- VCCRING_ WEST VCCP C RSVD_NC TF VCCRING_ WEST D --- E 4 5 6 7 8 9 10 11 12 13 14 15 16 --- --- XDP_RSV D_1 --- XDP_RSV D_8 --- VSS --- GTLREF --- --- VSS VCCP VSS --- XDP_RSV D_7 XDP_RSV D_11 VSS XDP_RSV D_15 XDP_RSV XDP_RSV D_14 D_16 VSS TCK --- VSS VCCRING_ WEST --- XDP_RSVD _3 XDP_RSV D_5 XDP_RSV D_4 XDP_RSV D_10 --- XDP_RSV D_12 XDP_RSV D_17 VSS --- TMS --- TRST# --- --- VCCP --- XDP_RSV D_2 --- XDP_RSV D_6 --- XDP_RSV D_0 TDO TDI --- --- RSVD_NC TF VCCP --- --- IGNNE# --- SMI# VSS --- VSS PRDY# --- THERMT RIP# --- BPM_1_1 # --- F --- DMI_RXN_0 DMI_RXP_ 0 VSS --- --- --- STPCLK# --- LINT0 LINT1 --- BPM_1_3 # --- PREQ# --- G DMI_TXN _0 DMI_TXP_0 DMI_RXN_ 1 --- RSVD DPRSTP# --- INIT# --- DPSLP# BPM_1_0 # --- BPM_1_2 # --- VSS --- H --- VSS BSEL_1 FERR# A20M# VSS --- BCLKN VSS --- RSVD --- VSS --- J RSVD DMI_TXN_1 --- VSS --- --- --- --- --- BCLKP VSS --- VSS --- VSS --- K --- RSVD RSVD VSS BSEL_0 BSEL_2 EXTBGREF VSS RSVD_TP --- VSS --- VSS --- VCC --- L VSS RSVD RSVD --- PWROK RSVD RSVD EXP_RBIA S EXP_ICO MPI EXP_RCO MPO RSVD --- VSS VCC --- VCC M --- RSVD VSS RSVD --- --- --- --- --- --- --- --- --- --- --- --- VSS RSVD RSVD RSVD_TP --- VSS VCC --- VCC RSVD_NC RSVD_NC TF TF DMI_TXP_ DMI_RXP 1 _1 EXP_CLKI EXP_CLKI NP NN XDP_RSV XDP_RSV D_9 D_13 N VSS RSVD --- VSS VSS P --- RSVD VSS VSS --- --- --- --- --- --- RSVD_TP --- VSS VSS --- VSS R --- --- --- --- RSVD_TP RSVD_TP VSS VSS RSVD RSVD --- --- --- --- --- --- Datasheet 75 Package Mechanical Specifications and Ball Information Figure 7-12.Package Pinmap (Top View, Upper-Right Quadrant) 17 76 18 19 20 21 --- VCC_LG I 22 23 24 25 26 --- VCC --- VCC --- 27 28 29 30 31 VCC --- RSVD_ NCTF RSVD_ NCTF --- A --- --- VSS --- BPM_2_ 0#/RSV D VSS BPM_2_ BPM_2_ 1#/RSV 3#/RSV D D VSS VCC VCC VCC VCC VCC --- VSSSEN RSVD_ SE NCTF RSVD_ NCTF B --- PROCH OT# --- BPM_2_ 2#/RSV D VSS VSS --- VCC VSS VCC --- --- THRMD VCCSE RSVD_ A_2/RS NSE NCTF VD C --- RSVD RSVD_T P RSVD --- VSS VCC VCC --- VCC --- VCC --- THRMD THRMD C_2/RS A_1 VD D RSVD --- VSS --- VSS VCC --- VCC VSS --- VCC --- VID_6 THRMD C_1 --- E VSS --- VSS --- VCC VCC --- VSS VCC --- --- VSS VID_5 --- --- F VSS --- VCC --- VCC VSS --- VCC --- --- VSS --- VID_4 VID_3 VSS G VCC --- VCC --- VSS VCC --- VCC VSS LVDD_E N VSS VID_2 VID_1 VID_0 --- H VCC --- VCC --- VCC VCC --- --- --- --- --- LVBG --- VCC --- VSS --- VCC --- LDDC_ CLK VSS VSS VSS PM_EXT TS#_1/ DPRSLP VR --- VSS VCC --- VCC VSS LCTLA_ CLK VSS VSS --- VSS --- --- --- --- --- --- --- --- --- --- VSS VCC --- VCC VSS VSS --- VSS VSS --- VSS --- --- --- --- --- --- --- --- LIBG LVREFH LVREFL --- LDDC_ LCTLB_ DATA DATA LA_DAT LA_DAT AN_0 AP_0 VSS LBKLT_ LBKLT_ CTL EN --- --- LA_DAT LA_DAT AN_1 AP_1 --- --- LA_DAT LA_DAT AN_2 AP_2 VSS VSS PM_EXT VCCRIN TS#_0 G_EAST VSS CRT_D CRT_D DC_CL DC_DA K TA CRT_VS CRT_H YNC SYNC --- --- --- CRT_IR CRT_R TN ED DAC_IR CRT_BL CRT_G EF UE REEN --- --- --- J K L M N --- P --- R Datasheet Package Mechanical Specifications and Ball Information Figure 7-13.Package Pinmap (Top View, Lower-Left Quadrant) VCCA_DM VCCA_DM I I T VCCA_DM I U --- --- V --- VCCA_DD R W CPUPWRG OOD VSS --- Y --- VCCA AA VCCSFR_D M IHM PLL AB --- --- --- VCCA_DD VCCA_DD R R --- --- --- VCCA_DD VCCA_D VCCA_D R DR DR --- --- --- VSS VSS VSS VSS VSS VSS --- --- --- VSS RSTIN# --- --- DDR_A_D Q_4 DDR_A_D Q_5 AC DDR_A_DQ _1 VSS --- DDR_A_D Q_0 --- --- AD --- DDR_A_D QS# _0 DDR_A_D QS_0 DDR_A_D M _0 VSS DDR_A_ DQ_15 AE VSS DDR_A_D Q_6 DDR_A_D Q_7 --- DDR_A_D Q_10 --- AF --- --- DDR_A_D Q_28 DDR_A_D Q_2 --- AG --- DDR_A_D Q_3 VSS --- DDR_A_D RSVD_T RSVD_TP Q_12 P DDR3_DR DDR_A_D DDR_A_ AM _PWR Q_13 DQ_8 OK --- VSS VCCGFX --- VCCGF X --- --- --- --- --- --- --- VSS VSS --- VSS --- RSVD_TP --- RSVD_T P --- RSVD --- VSS VSS --- DDR_A_ CK# _1 --- DDR_A _CK_3 --- DDR_A _DM _2 --- DDR_A_ DQ_23 VSS --- VSS --- VSS --- --- DDR_A_ DQ_20 DDR_A _DQ_21 --- DDR_A_ DQ_18 VSS --- DDR_A_ CK_4 --- DDR_A _CK# _0 --- DDR_A_D Q_11 --- DDR_A_ DQ_17 DDR_A _DQ_16 --- VSS DDR_A_D Q_19 --- DDR_A_ CK# _4 --- DDR_A _CK_0 --- --- VSS --- DDR_A_ M A_11 DDR_A_ DDR_A_ M A_8 M A_5 --- --- DDR_A_ M A_12 DDR_A_ M A_7 --- DDR_A_ M A_4 --- VSS DDR_A_ M A_9 VCCSM DDR_A_ M A_6 --- DDR_A _M A_3 --- --- DDR_A_ DQ_31 Datasheet VSS --- DDR_A_D M _3 3 --- --- --- RSVD_NCT DDR_A_D F Q_25 2 --- VSS VCCD_H M PLL DDR_A VCCACK VCCACK_ _DM _1 _DDR DDR DDR_A DDR_A _DQS_1 _DQ_14 --- --- VCCGFX --- DDR_A _CK# _3 AJ 1 VSS --- --- --- HPL_CL HPL_CL VCCA_D VCCA_DD KINN KINP DR R --- --- --- --- VSS RSVD_NC RSVD_NCT TF F --- --- VCCGFX VCCGFX DDR_A_ CK_1 --- --- --- VCCGF X --- --- VSS AL VCCA_ VCCA_D DDR DR --- VSS DDR_A_ DDR_A_D DQS# _2 Q_22 --- DDR_A_D QS# _3 --- --- --- DDR_A_DQ DDR_A_D _24 Q_29 RSVD_NCT RSVD_NC F TF --- VCCA_ DDR --- DDR_A_ DDR_A DQS# _1 _DQS_2 AH AK DDR_A_ DQ_9 --- DDR_A_ DDR_A DQ_27 _CKE_3 DDR_A DDR_A_ _CKE_1 CKE_0 --- DDR_A_ M A_14 --- DDR_A_D DDR_A_ QS_3 DQ_26 DDR3_ VCCCK_ DDR_A_ DDR_A_B DRAM R VCCSM DDR CKE_2 S_2 ST# --- DDR_A_D Q_30 --- VCCCK_ DDR --- VSS --- VCCSM --- VSS --- --- VCCSM 4 5 6 7 8 9 10 11 12 13 14 15 16 77 Package Mechanical Specifications and Ball Information Figure 7-14.Package Pinmap (Top View, Lower-Right Quadrant) --- VCCGF X --- RSVD_T P --- --- --- --- --- LA_CLK LA_CLK N P VCCAC VCC_GI RTDAC O --- --- VSS T VSS --- --- --- --- U --- --- --- --- --- VSS VSS VSS --- VSS VCCGF X --- RSVD_T P --- --- --- --- --- --- VSS VSS VCCALV DS --- V --- VCCGF X VCCGF X --- RSVD_T DDR_A P _DQ_59 VSS DDR_A _DQ_58 VSS VSS DDR_A _DQ_63 VSS --- VSS VCCDLV DS W --- --- --- --- --- --- --- --- --- VSS --- Y VSS DDR_A _DQS# _7 --- VSS VSS VSS VSS --- AB VSS --- VSS VCCSF R_AB_D PL AC --- AD --- --- --- VSS VCCD_ AB_DPL --- RSVD_T P VSS DDR_A DDR_A _DQ_62 _DQ_56 RSVD --- VSS --- VSS --- DDR_A DDR_A DDR_A DDR_A DDR_A _DQ_61 _DQ_60 _DQ_57 _DM_7 _DQS_7 RSVD --- VSS --- VSS DDR_A _DQ_44 --- RSVD --- DDR_A _DM_4 --- DDR_A DDR_A _DQ_39 _DQ_35 --- DDR_A DDR_A _DQ_43 _DQ_42 VSS --- DDR_A _DQ_32 --- DDR_A _DQ_38 VSS --- DDR_A _DQ_40 --- VSS --- DDR_A _DQ_37 --- VSS DDR_A _DQ_34 --- VSS --- DDR_A _DQ_36 --- --- --- 78 VCCGF X --- VSS --- DDR_A DDR_A _DQS# _DQS_4 _4 DDR_A DDR_A DDR_A VSS --_CS#_ _MA_0 _BS_1 0 DDR_A DDR_A DDR_A DDR_A _CS#_ --_CAS# _MA_1 _BS_0 2 --- DDR_A DDR_A _DQ_45 _DQ_41 VSS DDR_A _ODT_2 DDR_A DDR_A DDR_A DDR_A VCCSM _MA_2 _MA_10 _RAS# _WE# VSS --- DDR_A _DQ_33 --- --- --- --- VSS --- REFCLK REFCLK INN INP REFSSC REFSSC LKINP LKINN DDR_A DDR_A DDR_A DDR_A _DQ_46 _DQ_55 _DQ_51 _DQ_50 DDR_A DDR_A _DQS_5 _DQ_47 --- DDR_A DDR_A _DQ_54 _DQS_6 VSS AE DDR_A DDR_A _DQS# _DM_6 _6 --- AF --- --- VSS --- DDR_A _DQS# _5 --- --- DDR_A _ODT_1 --- VSS --- DDR_A DDR_A _DQ_49 _DQ_48 --- --- DDR_A DDR_A DDR_R DDR_A DDR_A DDR_A RSVD_ _CS#_ --_MA_13 PU _DM_5 _DQ_53 _DQ_52 NCTF 3 DDR_A DDR_A DDR_A DDR_R RSVD_ RSVD_ _CS#_ --RSVD _ODT_0 _ODT_3 PD NCTF NCTF 1 --- --- VSS --- VCCSM --- VSS --- VCCSM --- --- 17 18 19 20 21 22 23 24 25 26 27 AA DDR_V RSVD_ REF NCTF 28 29 RSVD_ NCTF --- 30 31 AG AH AJ AK AL Datasheet Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 1 of 9) Pin Number Type Dir. RSVD AB17 N/A N/A I DDR_A_CKE_0 AH10 MEM_Cntl_A O I DDR_A_CKE_1 AH9 MEM_Cntl_A O CPU legacy I/O DDR_A_CKE_2 AK10 MEM_Cntl_A O E15 CPU legacy I/O DDR_A_CKE_3 AJ8 MEM_Cntl_A O BPM_1_2# G13 CPU legacy I/O DDR_A_CS#_0 AH22 MEM_Cntl_A O BPM_1_3# F13 CPU legacy I/O DDR_A_CS#_1 AK25 MEM_Cntl_A O BPM_2_0#/ RSVD B18 CPU legacy I/O DDR_A_CS#_2 AJ21 MEM_Cntl_A O BPM_2_1#/ RSVD B20 CPU legacy I/O DDR_A_CS#_3 AJ25 MEM_Cntl_A O BPM_2_2#/ RSVD C20 CPU legacy I/O DDR_A_DM_0 AD4 MEM_Ad O BPM_2_3#/ RSVD B21 CPU legacy I/O DDR_A_DM_1 AA9 MEM_Ad O BSEL_0 K5 CPU legacy I/O DDR_A_DM_2 AE8 MEM_Ad O BSEL_1 H5 CPU legacy I/O DDR_A_DM_3 AJ3 MEM_Ad O BSEL_2 K6 CPU legacy I/O DDR_A_DM_4 AD19 MEM_Ad O CPUPWRGOOD W1 CPU legacy I DDR_A_DM_5 AJ27 MEM_Ad O CRT_BLUE P29 CRTDAC O DDR_A_DM_6 AF30 MEM_Ad O CRT_DDC_CLK L30 CRTDAC I/O DDR_A_DM_7 AB26 MEM_Ad O CRT_DDC_DAT A L31 CRTDAC I/O DDR_A_DQ_0 AC4 MEM_Ad I/O CRT_GREEN P30 CRTDAC O DDR_A_DQ_1 AC1 MEM_Ad I/O CRT_HSYNC M30 CRTDAC O DDR_A_DQ_10 AE5 MEM_Ad I/O CRT_IRTN N30 CRTDAC O DDR_A_DQ_11 AG5 MEM_Ad I/O CRT_RED N31 CRTDAC O DDR_A_DQ_12 AA5 MEM_Ad I/O CRT_VSYNC M29 CRTDAC O DDR_A_DQ_13 AB5 MEM_Ad I/O Pin Number Type Dir. A20M# H7 CPU legacy I/O BCLKN H10 CPU legacy BCLKP J10 CPU legacy BPM_1_0# G11 BPM_1_1# Pin Name Pin Name DAC_IREF P28 CRTDAC I/O DDR_A_DQ_14 AB9 MEM_Ad I/O DDR_A_BS_0 AJ20 MEM_Cntl_A O DDR_A_DQ_15 AD6 MEM_Ad I/O DDR_A_BS_1 AH20 MEM_Cntl_A O DDR_A_DQ_16 AG8 MEM_Ad I/O DDR_A_BS_2 AK11 MEM_Cntl_A O DDR_A_DQ_17 AG7 MEM_Ad I/O DDR_A_CAS# AJ22 MEM_Cntl_A O DDR_A_DQ_18 AF10 MEM_Ad I/O DDR_A_CK_0 AG15 MEM_Clk_A O DDR_A_DQ_19 AG11 MEM_Ad I/O DDR_A_CK_1 AD13 MEM_Clk_A O DDR_A_DQ_2 AF4 MEM_Ad I/O RSVD AD17 N/A N/A DDR_A_DQ_20 AF7 MEM_Ad I/O DDR_A_CK_3 AC15 MEM_Clk_A O DDR_A_DQ_21 AF8 MEM_Ad I/O Datasheet 79 Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 2 of 9) Pin Number Type Dir. DDR_A_DQ_22 AD11 MEM_Ad I/O N/A DDR_A_DQ_23 AE10 MEM_Ad I/O O DDR_A_DQ_24 AH1 MEM_Ad I/O DDR_A_DQ_25 AJ2 MEM_Ad I/O DDR_A_DQ_26 AK6 MEM_Ad I/O DDR_A_DQ_27 AJ7 MEM_Ad I/O DDR_A_DQ_28 AF3 MEM_Ad I/O Pin Number Type Dir. DDR_A_CK_4 AF13 MEM_Clk_A O RSVD AB15 N/A DDR_A_CK_0# AF15 MEM_Clk_A DDR_A_CK_1# AC13 MEM_Clk_A O RSVD AC17 N/A N/A DDR_A_CK_3# AD15 MEM_Clk_A O DDR_A_CK_4# AG13 MEM_Clk_A O Pin Name Pin Name DDR_A_DQ_29 AH2 MEM_Ad I/O DDR_A_DQ_8 AB6 MEM_Ad I/O DDR_A_DQ_3 AG2 MEM_Ad I/O DDR_A_DQ_9 AB7 MEM_Ad I/O DDR_A_DQ_30 AL5 MEM_Ad I/O DDR_A_DQS_0 AD3 MEM_Ad O DDR_A_DQ_31 AJ6 MEM_Ad I/O DDR_A_DQS_1 AB8 MEM_Ad O DDR_A_DQ_32 AE19 MEM_Ad I/O DDR_A_DQS_2 AD8 MEM_Ad O DDR_A_DQ_33 AG19 MEM_Ad I/O DDR_A_DQS_3 AK5 MEM_Ad O DDR_A_DQ_34 AF22 MEM_Ad I/O DDR_A_DQS_4 AG22 MEM_Ad O DDR_A_DQ_35 AD22 MEM_Ad I/O DDR_A_DQS_5 AE26 MEM_Ad O DDR_A_DQ_36 AG17 MEM_Ad I/O DDR_A_DQS_6 AE30 MEM_Ad O DDR_A_DQ_37 AF19 MEM_Ad I/O DDR_A_DQS_7 AB27 MEM_Ad O DDR_A_DQ_38 AE21 MEM_Ad I/O DDR_A_DQS#_0 AD2 MEM_Ad O DDR_A_DQ_39 AD21 MEM_Ad I/O DDR_A_DQS#_1 AD7 MEM_Ad O DDR_A_DQ_4 AB2 MEM_Ad I/O DDR_A_DQS#_2 AD10 MEM_Ad O DDR_A_DQ_40 AE24 MEM_Ad I/O DDR_A_DQS#_3 AK3 MEM_Ad O DDR_A_DQ_41 AG25 MEM_Ad I/O DDR_A_DQS#_4 AG21 MEM_Ad O DDR_A_DQ_42 AD25 MEM_Ad I/O DDR_A_DQS#_5 AG27 MEM_Ad O DDR_A_DQ_43 AD24 MEM_Ad I/O DDR_A_DQS#_6 AF29 MEM_Ad O DDR_A_DQ_44 AC22 MEM_Ad I/O DDR_A_DQS#_7 AA27 MEM_Ad O DDR_A_DQ_45 AG24 MEM_Ad I/O DDR_A_MA_0 AH19 MEM_Cntl_A O DDR_A_DQ_46 AD27 MEM_Ad I/O DDR_A_MA_1 AJ18 MEM_Cntl_A O DDR_A_DQ_47 AE27 MEM_Ad I/O DDR_A_MA_10 AK20 MEM_Cntl_A O DDR_A_DQ_48 AG31 MEM_Ad I/O DDR_A_MA_11 AH12 MEM_Cntl_A O DDR_A_DQ_49 AG30 MEM_Ad I/O DDR_A_MA_12 AJ11 MEM_Cntl_A O AB3 MEM_Ad I/O DDR_A_MA_13 AJ24 MEM_Cntl_A O DDR_A_DQ_5 DDR_A_DQ_50 AD30 MEM_Ad I/O DDR_A_MA_14 AJ10 MEM_Cntl_A O DDR_A_DQ_51 AD29 MEM_Ad I/O DDR_A_MA_2 AK18 MEM_Cntl_A O DDR_A_DQ_52 AJ30 MEM_Ad I/O DDR_A_MA_3 AK16 MEM_Cntl_A O DDR_A_DQ_53 AJ29 MEM_Ad I/O DDR_A_MA_4 AJ14 MEM_Cntl_A O DDR_A_DQ_54 AE29 MEM_Ad I/O DDR_A_MA_5 AH14 MEM_Cntl_A O 80 Datasheet Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 3 of 9) Pin Number Type Dir. DDR_A_MA_6 AK14 MEM_Cntl_A O I/O DDR_A_MA_8 AH13 MEM_Cntl_A O I/O DDR_A_MA_9 AK12 MEM_Cntl_A O Pin Name Pin Number Type Dir. DDR_A_DQ_55 AD28 MEM_Ad I/O DDR_A_DQ_56 AA24 MEM_Ad DDR_A_DQ_57 AB25 MEM_Ad Pin Name DDR_A_DQ_58 W24 MEM_Ad I/O DDR_A_ODT_0 AK24 MEM_Cntl_A O DDR_A_DQ_59 W22 MEM_Ad I/O DDR_A_ODT_1 AH26 MEM_Cntl_A O DDR_A_DQ_6 AE2 MEM_Ad I/O DDR_A_ODT_2 AH24 MEM_Cntl_A O DDR_A_DQ_60 AB24 MEM_Ad I/O DDR_A_ODT_3 AK27 MEM_Cntl_A O DDR_A_DQ_61 AB23 MEM_Ad I/O DDR_A_RAS# AK21 MEM_Cntl_A O DDR_A_DQ_62 AA23 MEM_Ad I/O INIT# G8 CPU_sideband I/O DDR_A_WE# AK22 MEM_Cntl_A O LBKLT_CTL L26 LVDS O DDR_RPD AK28 MEM_Ana I/O LBKLT_EN L27 LVDS O DDR_A_DQ_63 W27 MEM_Ad I/O LCTLA_CLK L23 LVDS I/O DDR_A_DQ_7 AE3 MEM_Ad I/O LCTLB_DATA K25 LVDS I/O DDR_RPU AJ26 MEM_Ana I/O LDDC_CLK K23 LVDS I/O RSVD AK29 N/A N/A LDDC_DATA K24 LVDS I/O DDR_VREF AL28 MEM_Ana I LINT0 F10 CPU_sideband I DMI_RXN_0 F2 3GIO_CTC_rx I LINT1 F11 CPU_sideband I DMI_RXN_1 G3 3GIO_CTC_rx I LA_CLKN U25 LVDS O RSVD J1 N/A N/A LA_CLKP U26 LVDS O RSVD L3 N/A N/A LA_DATAN_0 R23 LVDS O DMI_RXP_0 F3 3GIO_CTC_rx I LA_DATAN_1 N26 LVDS O DMI_RXP_1 H4 3GIO_CTC_rx I LA_DATAN_2 R26 LVDS O RSVD K2 N/A N/A LA_DATAP_0 R24 LVDS O RSVD M4 N/A N/A LA_DATAP_1 N27 LVDS O DMI_TXN_0 G1 3GIO_CTC_tx O LA_DATAP_2 R27 LVDS O DMI_TXN_1 J2 3GIO_CTC_tx O LIBG R22 LVDS I/O RSVD L2 N/A N/A LVBG J28 LVDS O RSVD N2 N/A N/A LVREFH N22 LVDS I DMI_TXP_0 G2 3GIO_CTC_tx O LVREFL N23 LVDS I DMI_TXP_1 H3 3GIO_CTC_tx O LVDD_EN H26 LVDS O RSVD K3 N/A N/A PM_EXTTS#_0 J30 HVCMOS I RSVD M2 N/A N/A PM_EXTTS#_1/ DPRSLPVR K29 HVCMOS I/O REFCLKINN Y29 Display PLL I PRDY# E11 CPU_sideband I/O REFCLKINP Y30 Display PLL I PREQ# F15 CPU_sideband I/O DPRSTP# G6 CPU_sideband I PROCHOT# C18 CPU_legacy I/O Datasheet 81 Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 4 of 9) Pin Number Type Dir. PWROK L5 HVCMOS I O EXP_CLKINN N7 3GIO_GFX_clk I I RSVD_TP AB11 N/A N/A 3GIO_GFX_ana I RSVD_TP AB13 N/A N/A 3GIO_GFX_ana I/O AK8 SSTL-1.5 O L10 3GIO_GFX_ana I RSVD_TP AA21 N/A N/A R10 N/A N/A RSVD_TP W21 N/A N/A Pin Number Type Dir. DPSLP# G10 CPU_sideband I DDR_A_MA_7 AJ12 MEM_Cntl_A EXP_CLKINP N6 3GIO_GFX_clk EXP_ICOMPI L9 EXP_RBIAS L8 EXP_RCOMPO RSVD Pin Name Pin Name DDR3_DRAMRST# RSVD R9 N/A N/A RSVD_TP T21 N/A N/A EXTBGREF K7 CPU_legacy I RSVD_TP V21 N/A N/A FERR# H6 CPU_sideband O REFSSCLKINN AA31 Clock I GTLREF A13 CPU_legacy I REFSSCLKINP AA30 Clock I HPL_CLKINN W8 Host PLL I RSVD L11 N/A N/A HPL_CLKINP W9 Host PLL I RSVD N10 N/A N/A IGNNE# E5 CPU_sideband I/O RSVD N9 N/A N/A RSVD_TP N11 N/A N/A VCC D24 PWR RSVD_TP P11 N/A N/A VCC D26 PWR RSVD_TP AA6 N/A N/A VCC D28 PWR RSVD_TP AA7 N/A N/A VCC E22 PWR RSVD_TP R6 N/A N/A VCC E24 PWR RSVD_TP R5 N/A N/A VCC E27 PWR RSVD H13 N/A N/A VCC F21 PWR RSVD D18 N/A N/A VCC F22 PWR RSVD L7 N/A N/A VCC F25 PWR RSVD D20 N/A N/A VCC G19 PWR RSVD L6 N/A N/A VCC G21 PWR RSVD E17 N/A N/A VCC G24 PWR DDR3_DRAM_P WROK AB4 CMOS-1.5 I VCC H17 PWR RSVD_TP K9 N/A N/A VCC H19 PWR RSVD_TP D19 N/A N/A VCC H22 PWR SMI# E7 CPU_sideband I/O VCC H24 PWR STPCLK# F8 CPU_sideband I VCC J17 PWR TCK B14 CPU_legacy I/O VCC J19 PWR TDI D14 CPU_legacy I/O VCC J21 PWR TDO D13 CPU_legacy I/O VCC J22 PWR G5 N/A N/A VCC K15 PWR RSVD 82 Datasheet Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 5 of 9) Pin Number Type VCC K17 PWR I VCC K21 PWR I THRMDA_2/RSVD C30 CPU_legacy Pin Number Type Dir. THERMTRIP# E13 CPU_sideband O THRMDA_1 D30 CPU_legacy RSTIN# AA3 HVCMOS Pin Name Pin Name THRMDC_1 E30 CPU_legacy O VCC L19 PWR THRMDC_2/ RSVD D31 CPU_legacy O VCC L21 PWR TMS C14 CPU_legacy I/O VCC N14 PWR TRST# C16 CPU_legacy I/O VCC N16 PWR VCC A23 PWR VCC N19 PWR VCC A25 PWR VCC N21 PWR VCC A27 PWR VCCP B3 PWR VCC B23 PWR VCCP B4 PWR VCC B24 PWR VCCP E2 PWR VCC B25 PWR VCCP D4 PWR VCC B26 PWR VCCRING_EAST J31 PWR VCC B27 PWR VCCRING_WEST B2 PWR VCC C24 PWR VCCRING_WEST C2 PWR VCC C26 PWR VCCRING_WEST C3 PWR VCC Dir. I D23 PWR VCCGFX W14 PWR VCCSM AK13 PWR VCCGFX W16 PWR VCCSM AK19 PWR VCCGFX W18 PWR VCCSM AK9 PWR VCCGFX W19 PWR VCCSM AL11 PWR VCCSENSE C29 PWR VCCSM AL16 PWR VCCSFR_AB_DPL AC31 PWR VCCSM AL21 PWR VCCSFR_DMIHMP LL AA1 PWR VCCSM AL25 PWR VID_0 H30 CPU_legacy O VCC_GIO T31 PWR VID_1 H29 CPU_legacy O VCC_LGI A21 PWR VID_2 H28 CPU_legacy O VCCA Y2 PWR VID_3 G30 CPU_legacy O VCCA_DDR U10 PWR VID_4 G29 CPU_legacy O VCCA_DDR U5 PWR VID_5 F29 CPU_legacy O VCCA_DDR U6 PWR VID_6 E29 CPU_legacy O VCCA_DDR U7 PWR VCCA_DDR U8 PWR VSS H27 VSS VCCA_DDR U9 PWR VSS A11 VSS Datasheet 83 Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 6 of 9) Pin Number Type VSS A16 VSS PWR VSS A19 VSS V4 PWR RSVD_NCTF A29 VSS VCC L14 PWR VCCA_DDR W10 PWR VCC L16 PWR VCCA_DDR W11 PWR VCCA_DMI T1 PWR RSVD_NCTF A4 VSS VCCA_DMI T2 PWR VSS AA13 VSS VCCA_DMI T3 PWR VSS AA14 VSS VCCALVDS V30 PWR VSS AA16 VSS VCCACK_DDR AA10 PWR VSS AA18 VSS VCCACK_DDR AA11 PWR VSS AA2 VSS VCCACRTDAC T30 PWR P2 N/A VCCCK_DDR AK7 VCCCK_DDR AL7 Pin Number Type VCCA_DDR V2 PWR VCCA_DDR V3 VCCA_DDR Pin Name RSVD VCCD_AB_DPL Dir. Pin Name VSS AA22 VSS VSS AA25 VSS PWR VSS AA26 VSS PWR VSS AA29 VSS N/A AA19 PWR VSS AA8 VSS VCCD_HMPLL V11 PWR VSS AB19 VSS VCCDLVDS W31 PWR VSS AB21 VSS VCCGFX T13 PWR VSS AB28 VSS VCCGFX T14 PWR VSS AB29 VSS VCCGFX T16 PWR VSS AB30 VSS VCCGFX T18 PWR VSS AC10 VSS VCCGFX T19 PWR VSS AC11 VSS VCCGFX V13 PWR VSS AC19 VSS VCCGFX V19 PWR VSS AC2 VSS VSS AC21 VSS VSS AL9 VSS VSS AC28 VSS VSS B13 VSS VSS AC30 VSS VSS B16 VSS VSS AD26 VSS VSS B19 VSS VSS AD5 VSS VSS B22 VSS VSS AE1 VSS RSVD_NCTF B30 VSS VSS AE11 VSS RSVD_NCTF B31 VSS VSS AE13 VSS VSS B5 VSS VSS AE15 VSS VSS B9 VSS VSS AE17 VSS RSVD_NCTF C1 VSS VSS AE22 VSS VSS C12 VSS 84 Dir. Datasheet Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 7 of 9) Pin Number Type VSS C21 VSS VSS VSS C22 VSS AF17 VSS VSS C25 VSS Pin Number Type VSS AE31 VSS VSS AF11 VSS VSS Pin Name Dir. Pin Name AF21 VSS RSVD_NCTF C31 VSS RSVD_NCTF A3 VSS VSS AF24 VSS RSVD_NCTF A30 VSS VSS AF28 VSS AG10 VSS VSS E10 VSS VSS VSS AG3 VSS VSS E19 VSS VSS AH18 VSS VSS E21 VSS VSS AH23 VSS VSS E25 VSS VSS AH28 VSS VSS E8 VSS VSS AH4 VSS VSS F17 VSS VSS AH6 VSS VSS F19 VSS VSS AH8 VSS VSS F24 VSS RSVD_NCTF AJ1 VSS VSS F28 VSS VSS AJ16 VSS VSS F4 VSS VSS AJ31 VSS VSS G15 VSS RSVD_NCTF AK1 VSS VSS G17 VSS RSVD_NCTF AK2 VSS VSS G22 VSS VSS AK23 VSS VSS G27 VSS RSVD_NCTF AK30 VSS VSS G31 VSS RSVD_NCTF AK31 VSS VSS H11 VSS VSS AL13 VSS VSS H15 VSS VSS AL19 VSS VSS H2 VSS AL2 VSS VSS H21 VSS VSS AL23 VSS VSS H25 VSS RSVD_NCTF AL29 VSS VSS H8 VSS RSVD_NCTF AL3 VSS VSS J11 VSS RSVD_NCTF AL30 VSS VSS J13 VSS VSS J15 VSS VSS T11 VSS VSS J4 VSS VSS U22 VSS VSS K11 VSS VSS U23 VSS VSS K13 VSS VSS U24 VSS VSS K19 VSS VSS U27 VSS VSS K26 VSS VSS V14 VSS VSS K27 VSS VSS V28 VSS RSVD_NCTF Datasheet Dir. 85 Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 8 of 9) Pin Number Type VSS V29 VSS VSS VSS W13 VSS K4 VSS VSS W2 VSS VSS K8 VSS VSS L13 VSS VSS L1 VSS VSS L18 VSS VSS D22 VSS VSS W23 VSS RSVD_NCTF E1 VSS VSS W25 VSS VSS L22 VSS VSS W26 VSS VSS L24 VSS VSS W28 VSS VSS L25 VSS VSS W30 VSS VSS L29 VSS VSS W4 VSS VSS M28 VSS VSS W5 VSS VSS M3 VSS VSS W6 VSS VSS N1 VSS VSS W7 VSS VSS N13 VSS VSS Y28 VSS VSS N18 VSS VSS Y3 VSS VSS N24 VSS VSS Y4 VSS VSS N25 VSS VSS T29 VSS VSS N28 VSS VSSSENSE B29 PWR VSS N4 VSS XDP_RSVD[0] D12 XDP VSS N5 VSS XDP_RSVD[1] A7 XDP VSS N8 VSS XDP_RSVD[2] D6 XDP VSS P13 VSS XDP_RSVD[3] C5 XDP VSS P14 VSS XDP_RSVD[4] C7 XDP VSS P16 VSS XDP_RSVD[5] C6 XDP VSS P18 VSS XDP_RSVD[6] D8 XDP VSS P19 VSS XDP_RSVD[7] B7 XDP VSS P21 VSS XDP_RSVD[8] A9 XDP VSS P3 VSS XDP_RSVD[9] D9 XDP VSS P4 VSS XDP_RSVD[10] C8 XDP VSS R25 VSS XDP_RSVD[11] B8 XDP VSS R7 VSS XDP_RSVD[12] C10 XDP VSS R8 VSS XDP_RSVD[13] D10 XDP VSS V16 VSS XDP_RSVD[14] B11 XDP VSS V18 VSS XDP_RSVD[15] B10 XDP Pin Number Type VSS K28 VSS VSS K30 VSS Pin Name 86 Dir. Pin Name Dir. Datasheet Package Mechanical Specifications and Ball Information Table 7-48.Processor Ball List by Ball Name (Sheet 9 of 9) Pin Name Pin Number Type XDP_RSVD[16] B12 XDP XDP_RSVD[17] C11 XDP Dir. Pin Name Pin Number Type Dir. Datasheet 87