Intel(R) 82562V 10/100 Mbps Platform LAN Connect Datasheet Product Features n n n n n n n n n IEEE 802.3 10BASE-T/100BASE-TX compliant physical layer interface IEEE 802.3u Auto-Negotiation support Digital Adaptive Equalization control Link status interrupt capability XOR tree mode support 3-port LED support (speed, link and activity) 10BASE-T auto-polarity correction LAN Connect Interface PHY detects polarity, MDI-X, and cable lengths. Auto MDI, MDIX crossover at all speeds n n n n n n n Diagnostic loopback mode 1:1 transmit transformer ratio support Low power (less than 300 mW in active transmit mode) Reduced power in "unplugged mode" (less than 50 mW) Automatic detection of "unplugged mode" 3.3 V device 81-pin Mold Cap package--10mm x 10mm x 1.745mm; 0.635mm Ball, 1.0mm Pitch Additional Features n n n The 82562V PLC supports strapping options that enable the following operating modes: -- LED support for three logic configurations. -- LAN disable function using one pin. -- Increased transmit strength. The receive BER performance increases the margin for cable length. Return Loss performance is improved. Revision 1.00 January 2006 317757-001 Revision History Revision Revision Date Description 0.25 July 2005 0.50 October 2005 Added correct package information and added more pin names and numbers 1.00 January 2006 Updated the power values and the signal names list Initial release. Information in this document is provided in connection with Intel(R) products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel(R) products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The 82562V PLC may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be obtained by calling 1-800-548-4725 or by visiting Intel's website at http://www.intel.com. Intel(R) is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. Copyright (c) 2005-2006, Intel Corporation * Other brands and names are the property of their respective owners. Datasheet Networking Silicon -- 82562V 1.0 Introduction This document is applicable to the Intel(R) 82562V 10/100 Mbps Platform LAN Connect device. 1.1 Overview The Intel(R) 82562V 10/100 Mbps Platform LAN Connect is a highly-integrated device designed for 10 or 100 Mbps Ethernet systems. It is based on the IEEE 10BASE-T and 100BASE-TX standards. The IEEE 802.3u standard for 100BASE-TX defines networking over two pairs of Category 5 unshielded twisted pair cable or Type 1 shielded twisted pair cable. The 82562V complies with the IEEE 802.3u Auto-Negotiation standard and the IEEE 802.3x Full Duplex Flow Control standard. The 82562V also includes a PHY interface compliant to the current platform LAN connect interface. 1.2 References * IEEE 802.3 Standard for Local and Metropolitan Area Networks, Institute of Electrical and Electronics Engineers. * 82562ET(EM) and 82562V(G) LAN on Motherboard Design Guide. Intel Corporation. * Intel(R) I/O Controller Hub 6 (ICH6) Family External Design Specification (EDS), Volume 1, Revision 1.5V1. Intel Corporation. * Intel(R) I/O Controller Hub 6 (ICH6) Family External Design Specification (EDS), Volume 2, Revision 1.5V2. Intel Corporation. * LAN Connect Interface Specification. Intel Corporation. * I/O Control Hub 2, 3, and 4 EEPROM Map and Programming Information. Intel Corporation. * I/O Control Hub 5, 6, and 7 EEPROM Map and Programming Information. Intel Corporation. Programming information can be obtained through your local Intel representatives. 1.3 Product Codes The product ordering code for the 82562V is: EP82562V. The product ordering code for the 82562V lead-free version is: LU82562V. Datasheet 1 82562V -- Networking Silicon 2.0 82562V Architectural Overview The 82562V PLC is a 3.3 V device in a 81-pin Mold Cap package. In normal operating mode, the 82562V incorporates all active circuitry required to interface with the Intel(R) ICHx device with an integrated 10/100 Mbps LAN controller. The 82562V supports a direct interface to all Media Access Control (MAC) components that meet the Platform LAN connect interface specification. Figure 1 shows a block diagram of the 82562V architecture. Digital Equalizer Adaptation LILED# Port LED Drivers ACTLED# SPDLED# Equalizer & BLW correction MDI/MDI-X RDN/RDP TDN/TDP Digital Clock Recovery (100) 100Base-TX PCS JRSTSYNC CRS/Link 10 Detection Digital Clock Recovery (10) 10Base-T PCS 3 LAN Connect Interface Transmit DAC 10/100 3 JTXD[2:0] JRXD[2:0] JCLK AutoNegotiation Bias & BandGap Voltage Circuit Clock Generator X1 Crystal 25 MHz Control Registers X2 Figure 1. 82562V PLC Block Diagram 2.1 LAN Connect Interface The 82562V supports a LAN Connect Interface (LCI) as specified in the LCI Specification. The LAN Connect is the I/O Control Hub 2 (ICH2) interface to the 82562V. The LCI uses an 8-pin interface, which reduces the pin count from 15, for an Media Independent Interface (MII) PHY. In addition, its signaling protocol provides greater functionality, such as dynamic power reduction, from a PLC in comparison to a standard MII PHY. Figure 2 shows how the 82562V can be used in a 10/100 Mbps ICHx design. I/O ControlHub Hub4 I/O Control LAN Controller (ICH4) LAN Controller Transmit Differential Pair (TDP/TDN) 82562EZ (PlatformPLC LAN 82562V Connect Device) Receive Differential Pair (RDP/RDN) Magnetics System Bus Interface 2 Datasheet Networking Silicon -- 82562V Figure 2. 82562V PLC 10/100 Mbps Ethernet Solution 2.1.1 Reset/Synchronize Operations The Reset/Synchronize signal used by the LAN Connect Interface is driven by the ICHx integrated LAN device. It has two functions: * Synchronize. When this pin is activated synchronously for only one LAN connect clock, it is used for synchronization between the ICHx integrated LAN and PHY on LAN connect word boundaries. * Reset. When this pin is asserted beyond one LAN connect clock, the 82562V uses this signal as a reset signal. To ensure a reset of the 82562V, the reset should remain active for at least 500 s. 2.1.2 Reset Considerations When the 82562V Reset signal (JRSTSYNC) is asserted for at least 500 s, all internal circuits are reset. The 82562V can also be reset by setting the MII register Reset bit equal to 1 (Register 0, bit 15). The 82562V filters out JRSTSYNC pulses with a width of less than 200 ns to distinguish between a reset and synchronize pulse. Again, the Reset signal should be longer than 500 s to reset the 82562V. Datasheet 3 82562V -- Networking Silicon 2.1.3 LAN Connect Clock Operations The 82562V drives the Platform LAN Connect clock (JCLK) at one of two possible frequencies depending upon its operation speed. When the 82562V is in 100BASE-TX mode it drives JCLK at 50 MHz. When the 82562V is in 10BASE-T mode it drives JCLK at 5 MHz. The LAN Connect clock does not stop during normal operation under any conditions. In reduced power mode, the 82562V drives JCLK at 5 MHz, which is required for proper filtering of incoming packets for applications such as Wake on LAN (WoL). 2.2 Hardware Configuration Four pins, Test Enable (TESTEN), Test Clock (ISOL_TCK), Test Input (ISOL_TI), and Test Execute (ISOL_EXEC), define the general operation of the 82562V. Table 1 lists the pin settings for the different modes of operation. Table 1. 82562V Hardware Configuration TESTEN ISOL _TCK ISOL _TI ISOL_ EXEC Mode 82562G family Mode 0: * LEDs are 82562E-compatible ("A" configuration) 0 0 0 0 * LAN_DISABLE# pin is used as ADV10 (auto-negotiation advertise 10M only) Alternative Mode: drop-in replacement for existing 82562Ebased designs Comments The ISOL_TCK, ISOL_TCI, and ISOL_EXEC, and ADV10/ LAN_DISABLE# pins have internal 10 K pull-down resistors and should not be connected for Mode 0 (refer to Table 2). For the alternative 82562E drop-in replacement mode, pins may optionally be used as a LAN disable. 82562G family Mode 1: * LEDs are in configuration B 0 0 1 1 0 1 1 1 Isolate 1 0 1 0 Testing Mode 1 0 0 0 XOR Tree Board testing plus tri-state. 82562G family Mode 2: 1 0 0 1 The ISOL_TCK and ISOL_TI pins have 10 K internal pull-down resistors and should not be connected for Mode 2 (refer to Table 2). 1 0 1 1 * LAN_DISABLE# pin is single pin LAN disable (tri-state and full power down function) Same as 0011 except that LEDs are in configuration C 82562G family Mode 3: Same as 0011 except enhance Tx rise and fall times. 82562G family Mode 4: 1 4 The ISOL_TCK pin has an internal 10 K pull-down resistor and should not be connected for Mode 1 (refer to Table 2). 1 0 0 Same as 1001 except Enhance Tx rise and fall times. Tri-state and power down. The ISOL_TCK pin has an internal 10 K pull-down resistor and should not be connected for Mode 3. The ISOL_TI and ISOL_EXEC pins have internal 10 K pull-down resistors and should not be connected for Mode 4. Datasheet Networking Silicon -- 82562V Table 1. 82562V Hardware Configuration TESTEN ISOL _TCK ISOL _TI ISOL_ EXEC 1 1 0 1 Reserved The ISOL_TI pin has an internal 10 K pull-down resistor and should not be connected. 1 1 1 0 Reserved Testing The ISOL_EXEC pin has an internal 10 K pull-down resistor and should not be connected. 1 1 1 1 Power-down Mode Tri-state and power down. Mode Comments NOTE: Combinations not shown in Table 1 are reserved and should not be used. Table 2. LED Logic Functionality Mode/Configuration Datasheet ACTLED # SPDLED# LILED# Configuration A: 82562ETcompatible Activity Speed 100 Mb Asserted if valid link is present at 10 Mb or 100 Mb Configuration B: Intel GbE mode Activity Link and Speed 100 Mb Asserted if valid link is present at 10 Mb or 100 Mb Configuration C: Alternative mode Activity Link and Speed 100 Mb Link and Speed 10 Mb 5 82562V -- Networking Silicon 3.0 Performance Enhancements 3.1 Usage Modes: 1, 2, 3, and 4 82562V supports several new features that offer design flexibility and reduced BOM cost compared to the 82562ET PLC device. To implement these new features, a board design must include the proper pull-up and/or pull-down strapping resistor options. Refer to the 82562V/ 82562GZ/82562GX/82562G LAN on Motherboard Design Guide for more information. Table 3 lists the four new modes. Table 3. Usage Modes 1, 2, 3, and 4 Mode Mode 0: 82562ET compatible. No BOM changes necessary for equivalent performance to 82562ET. Mode 1: LED configuration B and single-pin LAN disable. Usability and reduced BOM cost. Mode 2: Same as mode 1, except LED configuration C. Usability and reduced BOM cost. Mode 3: LED configuration B, Single Pin LAN Disable, and enhanced Tx modea Usability, reduced BOM cost, and stronger Tx drive strength. Refer to Section 3.1.2. Mode 4: Same as mode 3, except LED configuration C. See table note a. a. 3.1.1 Benefit Usability, reduced BOM cost, and stronger Tx drive strength. Refer to Section 3.1.2. Only use this mode if advised to do so by an Intel representative to compensate for board design issues affecting IEEE compliance. Pin Usage for Modes 1, 2, 3, and 4 To use modes 1, 2, 3, or 4, the following pins need to be reviewed (refer to Table 1): * * * * * * 6 ISOL_TCK ISOL_TI ISOL_EX TESTEN ADV10/LAN_DISABLE# and supporting circuits ACTLED#, SPDLED#, and LILED# and supporting circuits Datasheet Networking Silicon -- 82562V 3.1.2 Enhanced Tx Mode The enhanced Tx mode speeds up the rise and fall times of the 100 Mb signal. This was done so the 82562V can have improved IEEE PHY conformance requirements over a more capacitive Analog Front End (AFE); usually caused by long traces or differential switches that customers use, usually on mobile platforms. However, running an 82562V device in enhanced mode increases the radiated emissions seen from the LAN solution. The increase in radiated emissions may or may not impact the DUT's ability to pass regulatory requirements, as it will depend largely on the design of the AFE. The enhanced mode should only be used when 100Base-TX rise/fall times cannot be met in the normal 82562V mode. Consult an Intel representative if you are considering using this mode. 3.2 Management Data Interface MDI/MDI-X MDI/MDI-X provides the ability to automatically detect the required cable connection type and configure the controller-side MAU to the cable type. MDI/MDI-X effectively allows all properly wired Ethernet cables usable with any Ethernet device to be connected to the 82562V without any additional external logic. MDI/MDI-X enables auto-correction of incorrect cabling with respect to cross-over versus straight-through cables. The 82562V can identify the cable connection type and adjust its MDI port to the cable by switching between the TD and RD pairs. The auto-switching is done prior to the start of the hardware auto negotiation algorithm. In a standard straight-through RJ-45 port configuration, the transmit pair is on contacts 1 and 2, and the receive pair on contacts 3 and 6. These are defined by Clause 23.7.1 of the IEEE 802.3u standard. Table 4 lists the connections for both straight-through and cross-over RJ-45 ports for comparison. Table 4. RJ-45 Connections RJ-45 Contact Cross-Over MDIX Signalb 1 TD+ RD+ 2 TD- RD- 3 RD+ TD+ 4 Not Used Not Used 5 Not Used Not Used 6 RD- TD- 7 Not Used Not Used 8 Not Used Not Used a. b. Datasheet Straight-Through MDI Signala Straight-through connections used on Data Terminal Equipment (DTE) applications. Cross-over connections used on Hub and Switch applications. 7 82562V -- Networking Silicon Note: 8 This page intentionally left blank. Datasheet Networking Silicon -- 82562V 4.0 82562V Signal Descriptions 4.1 Signal Type Definitions Type 4.2 Name I Input O Output Output pin from the 82562V. I/O Input/Output Multiplexed input and output pin to and from the 82562V. MLT Multi-level analog I/O Multi-level analog pin used for input and output. B Bias Bias pin used for ground connection through a resistor or an external voltage reference. DPS Digital Power Supply Digital power or ground pin for the 82562V. APS Analog Power Supply Analog power or ground pin for the 82562V. Pin Number TDP B8 TDN B9 RDP D9 RDN D8 Type Description MLT Transmit Differential Pair. The transmit differential pair sends serial bit streams to the unshielded twisted pair (UTP) cable. The differential pair is a twolevel signal in 10BASE-T (Manchester) mode and a three-level signal in 100BASE-TX mode (MLT-3). These signals directly interface with the isolation transformer. MLT Receive Differential Pair. The receive differential pair receive the serial bit stream from an unshielded twisted pair (UTP) cable. The differential pair is a two-level signal in 10BASE-T mode (Manchester) or a three-level signal in 100BASE-TX mode (MLT-3). These signals directly interface with an isolation transformer. External Bias Pins Pin Name Pin Number Type Description RBIAS10 H7 B Reference Bias Resistor (100 Mbps). This pin should be connected to a pull-down resistor.a RBIAS100 G7 B Reference Bias Resistor (10 Mbps). This pin should be connected to a pulldown resistor.a a. Datasheet Input pin to the 82562V. Twisted Pair Ethernet (TPE) Pins Pin Name 4.3 Description Based on some board designs, RBIAS100 and RBIAS10 values may need to be increased/decreased to compensate for high/low MDI transmit amplitude. See the 82562G/GT and 82562ET/EM LAN on Motherboard Design Guide for more information. 9 82562V -- Networking Silicon 4.4 Clock Pins Pin Name 4.5 Pin Number Type Description X1 H6 I Crystal Input Clock. X1 and X2 can be driven by an external 25 MHz crystal of 30 PPM. Otherwise, X1 is driven by an external metal-oxide semiconductor (MOS) level 25 MHz oscillator when X2 is left floating. X2 H5 O Crystal Output Clock. X1 and X2 can be driven by an external 25 MHz crystal of 30 PPM. Platform LAN Connect Interface Pins Pin Name 4.6 Pin Number Type Description JCLK E2 O LAN Connect Clock. The LAN Connect Clock is driven by the 82562V on two frequencies depending on operation speed. When the 82562V is in 100BASE-TX mode, JCLK drives a 50 MHz clock. Otherwise, JCLK drives a 5 MHz clock for 10BASE-T. The JCLK does not stop during normal operation. JRSTSYNC E3 I Reset/Synchronize. This is a multiplexed pin and is driven by the Media Access Control (MAC) layer device. Its functions are: * Reset. When this pin is asserted beyond one LAN Connect clock period, the 82562V uses this signal Reset. To ensure reset of the 82562V, the Reset signal should remain active for at least 500 s. * Synchronize. When this pin is activated synchronously, for only one LAN Connect clock period, it is used to synchronize the MAC and PHY on LAN Connect word boundaries. JTXD[2:0] D1, F1, H9 I LAN Connect Transmit Data. The LAN Connect transmit pins are used to transfer data from the MAC device to the 82562V. These pins are used to move transmitted data and real time control and management data. They also transmit out of band control data from the MAC to the PHY. The pins should be fully synchronous to JCLK. JRXD[2:0] C1, D2, D3 O LAN Connect Receive Data. The LAN Connect receive pins are used to transfer data from the 82562V to the MAC device. These pins are used to move received data and real time control and management data. They also move out of band control data from the PHY to the MAC. These pins are synchronous to JCLK. LED Pins Pin Name Pin Number Type Description LILED# A4 O Link Integrity LED. The LILED# signal has three logic modes. The LED configurations are listed in Table 2, "LED Logic Functionality". ACTLED# B4 O Activity LED. The LED is active low and the Activity LED signal indicates either receive or transmit activity. When no activity is present, the LED is off. The Activity LED will flicker when activity is present. The flicker rate depends on the activity load. If Address Matching mode is enabled by the MAC, this pin will also indicate address match events on previously received frames. SPDLED# 10 A5 O Speed LED. The SPDLED# signal has three logic modes. The LED configurations are listed in Table 2, "LED Logic Functionality". Datasheet Networking Silicon -- 82562V 4.7 Miscellaneous Control Pins Pin Name ADV10/ LAN_DISABLE# Pin Number Type A6 I Description Advertise 10 Mbps Only. The Advertise 10 Mbps Only signal is asserted high, and the 82562V advertises only 10BASE-T technology during Auto-Negotiation processes in this state. Otherwise, the 82562V advertises all of its technologies. Note: ADV10 has an internal 10 K pull-down resistor. LAN Disable in 82562G Mode. In the 82562G operating mode, this pin is used as a LAN disable signal. When it is driven low, the device is fully powered down. ISOL_TCK G1 I Test Clock. The Test Clock signal sets the device into asynchronous test mode in conjunction with the Test Input, Test Execute and Test Enable pins (refer to Table 1, "82562V Hardware Configuration"). In the manufacturing test mode, it acts as the test clock. Note: ISOL_TCK has an internal 10 K pull-down resistor. ISOL_TI H1 I Test Input. The Test Input signal sets the device into asynchronous test mode in conjunction with the Test Clock, Test Execute and Test Enable pins (refer to Table 1, "82562V Hardware Configuration"). In the manufacturing test mode, it acts as the test data input pin. Note: ISOL_TI has an internal 10 K pull-down resistor. ISOL_EXEC G2 I Test Execute. The Test Execute signal sets the device into asynchronous test mode in conjunction with the Test Clock, Test Input, and Test Enable pins (refer to Table 1, "82562V Hardware Configuration"). In the manufacturing test mode, it places the command that was entered through the TI pin in the instruction register. Note: ISOL_EXEC has an internal 10 K pull-down resistor. TOUT G3 O Test Output. The Test Output pin is used for Boundary XOR scan output. In the manufacturing test mode, it acts as the test output port. TESTEN B6 I Test Enable. The Test Enable pin is used to enable test mode and should be externally pulled up to VCC using a 200 resistor to allow XOR Tree test mode. 4.8 Power and Ground Connections Pin Name VCC Pin Number Type Description B3, D4, E4, E5, E8, F2, F6, F7, G4, H3 DPS Digital 3.3 V Power. These pins should be connected to the main digital power supply. A8, C4, C7,C8, C9, D6, E1, E9, F4, G6, G8, G9, J3, J5 DPS Digital Ground. These pins should be connected to the main digital ground. VCCR D7 APS Analog Power. VSSR C6 APS Analog Ground. These pins should not be isolated from the main digital. VCCP VCCA VCCA2 VCCT VSS VSSP VSSA VSSA2 Datasheet 11 82562V -- Networking Silicon 5.0 Physical Layer Interface Functionality The 82562V supports a direct glueless interface to all components that comply with the LAN Connect specification. 5.1 100BASE-TX Mode 5.1.1 100BASE-TX Transmit Blocks The transmit subsection of the 82562V accepts 3 bit wide data from the LAN Connect unit. Another subsection passes data unconditionally to the 4B/5B encoder. The 4B/5B encoder accepts nibble-wide data (4 bits) from the CSMA unit and compiles it into 5bit-wide parallel symbols. These symbols are scrambled and serialized into a 125 Mbps bit stream, converted by the analog transmit driver into a MLT-3 waveform format, and transmitted onto the Unshielded Twisted Pair (UTP) or Shielded Twisted Pair (STP) wire. 5.1.1.1 100BASE-TX 4B/5B Encoder The 4B/5B encoder complies with the IEEE 802.3u 100BASE-TX standard. Four bits are encoded according to the transmit 4B/5B lookup table. The lookup table matches a 5-bit code to each 4-bit code. Table 5 lists the 4B/5B encoding scheme associated with the given symbol. Table 5. 4B/5B Encoder Symbol 12 5B Symbol Code 4B Nibble Code 0 11110 0000 1 01001 0001 2 10100 0010 3 10101 0011 4 01010 0100 5 01011 0101 6 01110 0110 7 01111 0111 8 10010 1000 9 10011 1001 A 10110 1010 B 10111 1011 C 11010 1100 D 11011 1101 E 11100 1110 F 11101 1111 I 11111 Inter Packet Idle Symbol (No 4B) Datasheet Networking Silicon -- 82562V 5.1.1.2 Symbol 5B Symbol Code 4B Nibble Code J 11000 1st Start of Packet Symbol 0101 K 10001 2nd Start of Packet Symbol 0101 T 01101 1st End of Packet Symbol R 00111 2nd End of Packet Symbol and Flow Control V 00000 INVALID V 00001 INVALID V 00010 INVALID V 00011 INVALID H 00100 INVALID V 00101 INVALID V 00110 INVALID V 01000 INVALID V 01100 INVALID V 10000 Flow Control S V 11001 INVALID 100BASE-TX Scrambler and MLT-3 Encoder Data is scrambled in 100BASE-TX in order to reduce electromagnetic emissions during long transmissions of high-frequency data codes. The scrambler logic accepts 5 bits from the 4B/5B encoder block and presents the scrambled data to the MLT-3 encoder. The 82562V implements the 11-bit stream cipher scrambler as adopted by the ANSI XT3T9.5 committee for UTP operation. The cipher equation used is: X[n] = X[n-11] + X[n-9] (mod 2) The MLT-3 encoder receives the scrambled Non-Return to Zero (NRZ) data stream from the scrambler and encodes the stream into MLT-3 for presentation to the driver. MLT-3 is similar to NRZ1 coding, but three levels are output instead of two. The three output levels are positive, negative and zero. When an NRZ "0" arrives at the input of the encoder, the last output level is maintained (either positive, negative or zero). When an NRZ "1" arrives at the input of the encoder, the output steps to the next level. The order of steps is negative-zero-positive-zero which continues periodically. Refer to IEEE 802.3 Specification for details. 5.1.1.3 100BASE-TX Transmit Framing The 82562V does not differentiate between the fields of the MAC frame containing preamble, start of frame delimiter, data and Cyclic Redundancy Check (CRC). The 82562V encodes the first byte of the preamble as the "JK" symbol, encodes all other pieces of data according to the 4B/5B lookup table, and adds the "TR" code after the end of the packet. The 82562V scrambles and serializes the data into a 125 Mbps stream, encodes it as MLT-3, and drives it onto the wire. Datasheet 13 82562V -- Networking Silicon 5.1.1.4 Transmit Driver The transmit differential lines are implemented with a digital slope controlled current driver that meets Twisted Pair Physical Media Device (TP-PMD) specifications. Current is sunk from the isolation transformer by the transmit differential pins. The conceptual transmit differential waveform for 100 Mbps is illustrated in Figure 3. Figure 3. Conceptual Transmit Differential Waveform The magnetics module external to the 82562V converts ITDP and ITDN to 2.0 VPP, as required by the TP-PMD specification. The same magnetics used for 100BASE-TX mode can also work in 10BASE-T mode. 5.1.2 100BASE-TX Receive Blocks The receive subsection of the 82562V accepts 100BASE-TX MLT-3 data on the receive differential pair. Due to the advanced digital signal processing design techniques employed, the 82562V accurately receives valid data from Category 5 (CAT5) UTP and Type 1 STP cables of length well in excess of 100 meters. 5.1.2.1 Adaptive Equalizer The distorted MLT-3 signal at the end of the wire is restored by the equalizer. The equalizer performs adaptation based on the shape of the received signal, equalizing the signal to meet superior data dependent jitter performance. 5.1.2.2 Receive Clock and Data Recovery The clock recovery circuit uses advanced digital signal processing technology to compensate for various signal jitter causes. The circuit recovers the 125 MHz clock and data and presents the data to the MLT-3 decoder. 5.1.2.3 MLT-3 Decoder, Descrambler, and Receive Digital Section The 82562V first decodes the MLT-3 data, and then the descrambler reproduces the 5B symbols originated in the transmitter. The descrambling is based on synchronization to the transmission of the 11-bit Linear Feedback Shift Register (LFSR) during an idle phase. The data is decoded at the 4B/5B decoder. After the 4B symbols are obtained, the 82562V outputs the receive data to the CSMA unit. 14 Datasheet Networking Silicon -- 82562V In 100BASE-TX mode, the 82562V can detect errors in receive data in a number of ways. Any of the following conditions is considered an error: * * * * Link integrity fails in the middle of frame reception. The start of stream delimiter "JK" symbol is not fully detected after idle. An invalid symbol is detected at the 4B/5B decoder. Idle is detected in the middle of a frame (before "TR" is detected). 5.2 10BASE-T Mode 5.2.1 10BASE-T Transmit Blocks 5.2.1.1 10BASE-T Manchester Encoder After the 2.5 MHz clocked data is serialized in a 10 Mbps serial stream, the 20 MHz clock performs the Manchester encoding. The Manchester code always has a mid-bit transition. The boundary transition occurs only when the data is the same from bit to bit. For example, if the value is 11b, then the change is from low to high within the boundary. 5.2.1.2 10BASE-T Driver and Filter Since 10BASE-T and 100BASE-TX have different filtration needs, both filters are implemented inside the chip. The 82562V supports both technologies through one pair of transmit differential pins and by externally sharing the same magnetics. In 10 Mbps mode the line drivers use a pre-distortion algorithm to improve jitter tolerance. The line drivers reduce their drive level during the second half of "wide" (100 ns) Manchester pulses and maintain a full drive level during all narrow (50 ns) pulses and the first half of the wide pulses. This reduces line overcharging during wide pulses, a major source of jitter. 5.2.2 10BASE-T Receive Blocks 5.2.2.1 10BASE-T Manchester Decoder The 82562V performs Manchester decoding and timing recovery in 10BASE-T mode. The Manchester encoded data stream is decoded from the receive differential pair. This data is transferred to the controller at 2.5 MHz/nibble. The high-performance circuitry of the 82562V exceeds the IEEE 802.3 jitter requirements. 5.2.2.2 10BASE-T Twisted Pair Ethernet (TPE) Receive Buffer and Filter In 10 Mbps mode, data is expected to be received on the receive differential pair after passing through isolation transformers. The filter is implemented inside the 82562V for supporting single magnetics that are shared with the 100BASE-TX side. The input differential voltage range for the Twisted Pair Ethernet (TPE) receiver is greater than 585 mV and less than 3.1 V. The TPE receive buffer distinguishes valid receive data, link test pulses, and the idle condition, according to the requirements of the 10BASE-T standard. The following line activity is determined to be inactive and is rejected as invalid data: Datasheet 15 82562V -- Networking Silicon * Differential pulses of peak magnitude less than 300 mV. * Continuous sinusoids with a differential amplitude less than 6.2 VPP and frequency less than 2 MHz. * Sine waves of a single cycle duration starting with 0 or 180 phase that have a differential amplitude less than 6.2 VPP and a frequency of at least 2 MHz and not more than 16 MHz. These single-cycle sine waves are discarded only if they are preceded by 4 bit times (400 ns) of silence. All other activity is determined to be either data, link test pulses, Auto-Negotiation fast link pulses, or the idle condition. 5.3 Analog References The 82562V has two inputs, RBIAS100 and RBIAS10, that require external resistor connections to set biases for its internal analog section. The input pins are sensitive to the resistor value and experimentation is required to determine the correct values for any given layout. Note that the values listed in Figure 4 are starting values. Also, resistors of 1% tolerance should be used. Figure 4. Analog References 82562 5491% 619 1% 619 1% 649 1% 5.4 RBIAS10 RBIAS100 Dynamic Reduced Power & Auto Plugging Detection The 82562V can be configured to support a dynamic reduced power mode. This mode reduces power consumption of the 82562V when LAN activity is not present. The reduced power mode decreases power consumption from 300 mW to about 50 mW and is based on automatic detection of cable plugging. If the 82562V is configured to support dynamic power reduction, it enters the reduced power mode whenever a cable is not connected to the device. In reduced power mode, the 82562V shuts off the link circuits, except the circuit used for the automatic plugging detection. On the LAN Connect side, the entire interface remains active, including full access to all Media Independent Interface (MII) registers. In this mode, the 82562V switches to the 10 Mbps speed interface (5 MHz for LAN Connect). Thus, the reduced power mode is fully transparent to driver. 16 Datasheet Networking Silicon -- 82562V 5.4.1 Auto Plugging Detection The 82562V senses the link all the time. If it detects loss of any link activity for more than 6.6 seconds, it indicates to the Media Access Controller (MAC) an "unplugged state" by resetting the SQL LAN Connect control bit. If the 82562V is in reduced power mode and link activity is detected, the 82562V notifies the MAC (in less than 1 second) that it is in a "plugged state" by setting the SQL LAN Connect control bit. Link activity detection is based on energy detection. 5.4.2 Dynamic Reduced Power The 82562V can be configured to support dynamic reduced power. In the dynamic reduced power mode, the 82562V transitions to reduced power mode when an unplugged state is detected. The 82562V only returns to full power if the reduced power bit on the LAN Connect is reset and a plugged state is detected. However, if the 82562V is not configured to support dynamic reduced power, the 82562V operates according to the LAN Connect power-down bit (in other words, the 82562V operates in reduced power mode only if the LAN Connect power-down bit is set). 5.4.3 Configuration The dynamic reduced power mode is configured through bit 13 of register 16. The default value is disabled (0). The status of the 82562V is read through bits 10:9 of register 16. When the 82562V is in reduced power mode, these two bits are set to 1b. Table 6. Register 16 (10 Hexadecimal): PLC Status, Control and Address Data Bit 13 Name Dynamic Reduced Power Down Description 0 = Automatic reduced power down enabled Read/Write Read/Write 1 = Automatic reduced power down disabled (default) 10 100BASE-TX Power Down The 100BASE-TX Power Down bit indicates the power state. Read Only 0 = Normal operation (default) 1 = Power down 9 10BASE-T Power Down The 10BASE-T Power Down bit indicates the power state. Read Only 0 = Normal operation (default) 1 = Power down The 82562V PLC can enter a reduced power state manually through bit 11 of register 0. This bit is ORed with the LAN Connect power down bit, which enables the 82562V to enter a reduced power state. Table 7. Register 0: Control Data Bit 11 Name Reduced Power Down Description 0 = Reduced power down disabled (normal operation; default) Read/Write Read/Write 1 = Reduced power down enabled Datasheet 17 82562V -- Networking Silicon 6.0 Platform LAN Connect Registers The following sections describe PHY registers that are accessible through the LAN Connect management frame protocol. Acronyms mentioned in the registers are defined as follows: SC: Self cleared. RO: Read only. RW: Read/Write. E: EEPROM setting affects content. LL: Latch low. LH: Latch high. 6.1 Medium Dependent Interface (MDI) Registers 0 through 7 6.1.1 Register 0: Control Register Bit Definitions Bit(s) 15 Name Reset Description Default R/W This bit sets the status and control register of the PHY to their default states and is self-clearing. The PHY returns a value of one until the reset process has completed and accepts a read or write transaction. 0 RW SC 0 = Normal operation 1 = PHY Reset 14 Loopback This bit enables loopback of transmit data nibbles to the receive data path. The PHY receive circuitry is isolated from the network. 0 RW 1 RW 1 RW 0 RW Note that this may cause the descrambler to lose synchronization and produce 560 ns of "dead time." Note also that the loopback configuration bit takes priority over the Loopback MDI bit. 0 = Loopback disabled (normal operation) 1 = Loopback enabled 13 Speed Selection This bit is valid on read and controls speed when AutoNegotiation is disabled. 0 = 10 Mbps 1 = 100 Mbps 12 Auto-Negotiation Enable This bit enables Auto-Negotiation. Bits 13 and 8, Speed Selection and Duplex Mode, respectively, are ignored when Auto-Negotiation is enabled. 0 = Auto-Negotiation disabled 1 = Auto-Negotiation enabled 11 Reduced Power Down This bit sets the PHY into a low power mode. 0 = Power down disabled (normal operation) 1 = Power down enabled 18 Datasheet Networking Silicon -- 82562V Bit(s) 10 Name Isolate Description Default R/W 0 RW 0 RW This bit allows the PHY to isolate the medium independent interface. The PHY is disconnected from the LAN Connect block on both the transmit and receive side. 0 = Normal operation 1 = Isolates internal medium independent interface 9 Restart AutoNegotiation This bit restarts the Auto-Negotiation process and is selfclearing. SC 0 = Normal operation 1 = Restart Auto-Negotiation process 8 Duplex Mode This bit controls the duplex mode when Auto-Negotiation is disabled. When Auto-Negotiation is enabled this bit is read only and always equals 1b. 0 RW/ RO When the PHY is placed in Loopback mode, the behavior of the PHY shall not be affected by the status of this bit. 0 = Half Duplex 1 = Full Duplex 6.1.2 7 Collision Test This bit is not used in the 82562V and has a default value of 1b. (If it is used in other devices, it forces a collision in response to the assertion of the transmit enable signal.) 1 RW 6:0 Reserved These bits are reserved and should be set to 0b. 0 RW Register 1: Status Register Bit Definitions Bit(s) Name Description Default R/W 15 Reserved This bit is reserved and should be set to 0b. 0 RO 14 100BASE-TX Fullduplex This bit enables 100BASE-TX full-duplex operation and is dependent on ADV10. If ADV10 is active, the default value is 0. 1 RO 1 RO 1 RO 1 RO 0 = PHY unable to perform full-duplex 100BASE-TX 1 = PHY able to perform full-duplex 100BASE-TX 13 100 Mbps Halfduplex This bit enables 100BASE-TX half-duplex operation and is dependent on ADV10. If ADV10 is active, the default value is 0. 0 = PHY unable to perform half-duplex 100BASE-TX 1 = PHY able to perform half-duplex 100BASE-TX 12 10 Mbps Fullduplex This bit enables 10BASE-T full duplex operation. 0 = PHY unable to perform full-duplex 10BASE-T 1 = PHY able to perform full-duplex 10BASE-T 11 10 Mbps Halfduplex This bit enables 10BASE-T half-duplex operation. 0 = PHY unable to perform half-duplex 10BASE-T 1 = PHY able to perform half-duplex 10BASE-T 10:7 Reserved These bits are reserved and should be set to 0b. 0 RO 6 Management Frames Preamble Suppression This bit allows the 82562V to receive management frames with suppressed preamble. 0 RO 0 = PHY will not accept management frames with preamble suppressed 1 = PHY will accept management frames with preamble suppressed Datasheet 19 82562V -- Networking Silicon Bit(s) 5 Name Auto-Negotiation Complete Description This bit reflects status of the Auto-Negotiation process. Default R/W 0 RO 0 RO 1 RO 0 = Auto-Negotiation process has not completed 1 = Auto-Negotiation process completed 4 Remote Fault 0 = No remote fault condition detected 1 = Remote fault condition detected 3 Auto-Negotiation Ability 0 = PHY is unable to perform Auto-Negotiation This bit reflects the PHY's Auto-Negotiation ability status. Link Status This bit reflects link status. 1 = PHY is able to perform Auto-Negotiation 2 0 0 = Invalid link detected RO LL 1 = Valid link established 1 Jabber Detect This bit is used only in 10BASE-T mode. 0 0 = No jabber condition detected RO LH 1 = Jabber condition detected 0 Extended Capability This bit enables the extended register capabilities. 1 RO 0 = Extended register capabilities disabled 1 = Extended register capabilities enabled 6.1.3 Register 2: PHY Identifier Register Bit Definitions Bit(s) 15:0 6.1.4 PHY ID (high byte) Description Value: 02A8 hexadecimal Default -- R/W RO Register 3: PHY Identifier Register Bit Definitions Bit(s) 6.1.5 Name Name Description Default R/W 15:0 PHY ID (low byte) Value: 0330 hexadecimal for 82562V PLC (and 82562GZ) -- RO 15:0 PHY ID (low byte) Value: 0310 hexadecimal for 82562G -- RO Register 4: Auto-Negotiation Advertisement Register Bit Definitions Bit(s) Name Description Default R/W 15 Next Page This bit is a constant 0, transmit primary capability data page. 0 RO 14 Reserved This bit is reserved and should be set to 0b. 0 RO 13 Remote Fault 0 = No remote fault 0 RW 00101111 RW 00001 RO 1 = Indicate link partner's remote fault 20 12:5 Technology Ability Field Technology Ability Field is an 8-bit field containing information indicating supported technologies specific to the selector field value. 4:0 Selector Field The Selector Field is a 5-bit field identifying the type of message to be sent by Auto-Negotiation. This field is read only and contains a value of 00001b, IEEE Standard 802.3. Datasheet Networking Silicon -- 82562V 6.1.6 Register 5: Auto-Negotiation Link Partner Ability Register Bit Definitions Bit(s) 6.1.7 Name Description Default R/W 15 Next Page This bit reflects the PHY's link partner's Next Page ability. -- RO 14 Acknowledge This bit is used to indicate that the 82562V has successfully received its link partner's Auto-Negotiation advertising ability. -- RO 13 Remote Fault This bit reflects the PHY's link partner's Remote Fault condition. -- RO 12:5 Technology Ability Field This bit reflects the PHY's link partner's Technology Ability Field. -- RO 4:0 Selector Field This bit reflects the PHY's link partner's Selector Field. -- RO Register 6: Auto-Negotiation Expansion Register Bit Definitions Bit(s) Name Description Default R/W 15:5 Reserved These bits are reserved and should be set to 0b. 0 RO 4 Parallel Detection Fault This bit clears itself on read. 0 RO 3 2 0 = No fault detected via parallel detection SC 1 = Fault detected via parallel detection (multiple link fault occurred) LH Link Partner Next Page Able 0 = Link Partner is not Next Page able Next Page Able 0 = 0 = Local drive is not Next Page able 0 RO 0 RO 0 RO 1 = Link Partner is Next Page able 1 = Local drive is Next Page able 1 0 6.2 Page Received Link Partner AutoNegotiation Able This bit clears itself on read. 0 = New Page not received SC 1 = New Page received LH 0 = Link Partner is not Auto-Negotiation able 0 RO 1 = Link Partner is Auto-Negotiation able MDI Registers 8 through 15 Registers 8 through 15 are reserved for IEEE. Datasheet 21 82562V -- Networking Silicon 6.3 MDI Registers 16 through 31 6.3.1 Register 16: PHY Status and Control Register Bit Definitions Bit(s) Name Description Default R/W 15:14 Reserved These bits are reserved and should be set to 00b. 00 RW 13 Reduced Power Down Disable This bit disables the automatic reduced power down. 1 RW 0 = Enable automatic reduced power down 1 = Disable automatic reduced power down 12 Reserved This bit is reserved and should be set to 0b. 0 RW 11 Receive DeSerializer In-Sync Indication This bit indicates status of the 100BASE-TX Receive DeSerializer In-Sync. -- RO 10 100BASE-TX Power-Down This bit indicates the power state of 100BASE-TX PHY unit. 1 RO 1 RO -- RO 0 = Normal operation 1 = Power-down 9 10BASE-T PowerDown 0 = Normal operation This bit indicates the power state of 10BASE-T PHY unit. Polarity This bit indicates 10BASE-T polarity. 1 = Power-Down 8 0 = Normal polarity 1 = Reverse polarity 7 Reserved This bit is reserved and should be set to 0b. 0 RO 6:2 PHY Address These bits contain the sampled PHY address. -- RO 1 Speed This bit indicates the Auto-Negotiation result. -- RO -- RO 0 = 10 Mbps 1 = 100 Mbps 0 Duplex Mode This bit indicates the Auto-Negotiation result. 0 = Half-duplex 1 = Full-duplex 6.3.2 Register 17: PHY Unit Special Control Bit Definitions Bit(s) 15 Name Scrambler By-pass Description 0 = Normal operations Default R/W 0 RW 0 RW 0 RW 0 RW 1 = By-pass scrambler 14 By-pass 4B/5B 0 = Normal operation 1 = 4 bit to 5 bit by-pass 13 12 22 Force Transmit HPattern 0 = Normal operation Force 34 Transmit Pattern 0 = Normal operation 1 = Force transmit H-pattern 1 = Force 34 transmit pattern Datasheet Networking Silicon -- 82562V Bit(s) 11 Name Valid Link Description 0 = Normal operation Default R/W 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 1 = 100BASE-TX valid link 10 9 Symbol Error Enable 0 = Normal operation Carrier Sense Disable This bit controls the receive 100 carrier sense disable function. 1 = Symbol error output is enabled 0 = Carrier sense enabled 1 = Carrier sense disabled 8 7 6 Disable Dynamic Power-Down 0 = Dynamic Power-Down enabled Auto-Negotiation Loopback 0 = Auto-Negotiation normal mode MDI Tri-State 1 = Dynamic Power-Down disabled 1 = Auto-Negotiation loopback 0 = Normal operation 1 = MDI Tri-state (transmit driver tri-states) 5 Force Polarity 0 = Normal polarity 1 = Reversed polarity 4 3 Auto Polarity Disable 0 = Normal polarity operation Squelch Disable 0 = Normal squelch operation 1 = Auto Polarity disabled 1 = 10BASE-T squelch test disable 2 Extended Squelch 1 = 10BASE-T Extended Squelch control enabled 0 = 10BASE-T Extended Squelch control disabled 1 0 6.3.3 15:0 Jabber Function Disable 0 = Normal Jabber operation 1 = Link disabled 1 = Jabber disabled Name Reserved Description These bits are reserved and should be set to a constant 0b. Default 0 R/W RO Register 19: 100BASE-TX Receive False Carrier Counter Bit Definitions Bit(s) 15:0 Datasheet 0 = Normal Link Integrity operation Register 18: Reserved Bit(s) 6.3.4 Link Integrity Disable Name Receive False Carrier Description These bits are used for the false carrier counter. Default -- R/W RO SC 23 82562V -- Networking Silicon 6.3.5 Register 20: 100BASE-TX Receive Disconnect Counter Bit Definitions Bit(s) 15:0 6.3.6 Disconnect Event Description Default This field contains a 16-bit counter that increments for each disconnect event. The counter stops when it is full and selfclears on read -- R/W RO SC Register 21: 100BASE-TX Receive Error Frame Counter Bit Definitions Bit(s) 15:0 6.3.7 Name Name Receive Error Frame Description Default This field contains a 16-bit counter that increments once per frame for any receive error condition (such as a symbol error or premature end of frame) in that frame. The counter stops when it is full and self-clears on read. -- R/W RO SC Register 22: Receive Symbol Error Counter Bit Definitions Bit(s) 15:0 Name Symbol Error Counter Description Default This field contains a 16-bit counter that increments for each symbol error. The counter stops when it is full and selfclears on read. -- R/W RO SC In a frame with a bad symbol, each sequential six bad symbols count as one. 6.3.8 Register 23: 100BASE-TX Receive Premature End of Frame Error Counter Bit Definitions Bit(s) 15:0 6.3.9 15:0 Default This field contains a 16-bit counter that increments for each premature end of frame event. The counter stops when it is full and self-clears on read. -- R/W RO SC Name End of Frame Counter Description This is a 16-bit counter that increments for each end of frame event. The counter stops when it is full and selfclears on read. Default -- R/W RO SC Register 25: 10BASE-T Transmit Jabber Detect Counter Bit Definitions Bit(s) 15:0 24 Premature End of Frame Description Register 24: 10BASE-T Receive End of Frame Error Counter Bit Definitions Bit(s) 6.3.10 Name Name Jabber Detect Counter Description Default This is a 16-bit counter that increments for each jabber detection event. The counter stops when it is full and selfclears on read. -- R/W RO SC Datasheet Networking Silicon -- 82562V 6.3.11 Register 27: PHY Unit Special Control Bit Definitions Bit(s) Name Description Default R/W 15:6 Reserved These bits are reserved and should be set to a constant 0. 0 RO 5 Switch Probe Mapping This bit switches the mapping on the LEDs. The LED mapping is described below in bits 2:0, LED Switch Control. This bit should always be set to 0b. 0 RW 4 New mode If this bit equals 0, the device is in 82562EZ (or 82562ET) mode. RO If this bit equals 1, the device is in 82562V (or 82562GZ) mode. 6.3.12 3 100BASE-TX Receive Jabber Disable 2:0 LED Switch Control This bit enables the carrier sense disconnection while the PHY is in jabber mode at 100 Mbps speed. Value ACTLED# LILED# 000 Activity Link 001 Speed Collision 010 Speed Link 011 Activity Collision 100 Off Off 101 Off On 110 On Off 111 On On 0 RW 000 RW Register 28: MDI/MDI-X Control Bit Definitions Bit(s) Name Description Default R/W 15:8 Reserved These bits are reserved and should be set to a constant 0. 0 RW 7 Auto Switch Enable Enables the MDI/MDI-X feature (writing to this bit overwrites the default value). 0 RW 1 = Enabled. 0 = Disabled. 6 Switch RW Manual switch (valid only if bit 7 is set to 0). 1 = Forces the port to be MDI-X (cross-over). 0 0 = Forces the port to be MDI (straight-through). 5 Status Indicates the state of the MDI pair. 0 RO 0 RO 0000 RW 1 = MDI-X (cross-over). 0 = MDI (straight-through). 4 Auto Switch Complete Indicates when the correct configuration is achieved. 1 = Resolution algorithm has completed. 0 = Resolution algorithm has not completed. 3:0 Resolution Timer Defines the minimum slot time the algorithm uses in order to switch between one configuration or another. 0000 = 80 ms. 1111 = 105 ms. Datasheet 25 82562V -- Networking Silicon Note: 26 This page intentionally left blank. Datasheet Networking Silicon -- 82562V 7.0 82562V Test Port Functionality The 82562V's XOR Tree Test Access Port (TAP) is the access point for test data to and from the device. The port provides the ability to perform basic production level testing. 7.1 Asynchronous Test Mode An asynchronous test mode is supported for system level design use. The modes are selected through the use of the Test Port input pins (TESTEN, ISOL_TCK, ISOL_TI and ISOL_EXEC) in static combinations. During normal operation the test pins must be pulled down through a resistor (pulling Test high enables the test mode). All other port inputs may have a pull-down at the designers discretion. 7.2 Test Function Description The 82562V TAP mode supports several tests that can be used in board level design. These tests can help verify basic functionality and test the integrity of solder connections on the board. The tests are described in the following sections. The XOR Tree test mode is the most useful of the asynchronous test modes. It enables the placement of the 82562V to be validated at board test. The XOR Tree was chosen for its speed advantages. Modern Automated Test Equipment (ATE) can perform a complete peripheral scan without support at the board level. This command connects all output signals of the input buffers in the device periphery into an XOR Tree scheme. All output drivers of the output-buffers, except the test output (TOUT) pin, are put into high-Z mode. These pins are driven to affect the tree's output. Any hard strapped pins will prevent the tester from scanning correctly. The XOR Tree test mode is obtained by placing the test pins in the following configuration (refer to Table 8): TESTEN = 1 ISOL_TCK = 0 ISOL_TI = 0 ISOL_EXEC = 0. Table 8. XOR Tree Chain Order Chain Order Datasheet Chain 1 JTXD2 2 JTXD1 3 JTXD0 4 JRSTSYNC 5 ADV10 (LAN_DISABLE#) 6 JCLK 7 JRXD2 8 JRXD1 9 JRXD0 10 ACTLED# 27 82562V -- Networking Silicon Table 8. XOR Tree Chain Order Chain Order Chain 11 SPDLED# 12 LILED# XOR Tree Output TOUT The following pins are not included in the XOR Tree chain: X1, ISOL_TCK, ISOL_EXEC, ISOL_TI and TESTEN. 28 Datasheet Networking Silicon -- 82562V 8.0 Electrical and Timing Specifications 8.1 Absolute Maximum Ratings Maximum ratings are listed below: Case Temperature under Stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 C to 135 C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65 C to 150 C Supply Voltage with respect to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 3.45 V Output Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.50 V to 3.45 V Input Voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC to 3.45 V Stresses above the listed absolute maximum ratings may cause permanent damage to the 82562V device. This is a stress rating only and functional operations of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 8.2 DC Characteristics Table 9. General DC Specifications Symbol Datasheet Parameter Condition Min Typical Max Units 3.0 3.3 3.45 V 85 C VCC Supply Voltage T Temperature Minimum/Maximum Case Temperature P Power Consumption 10/100 Mbps (transmitter on) 300 mW Reduced Power 50 mW Auto-Negotiation 200 mW 0 Notes 29 82562V -- Networking Silicon Table 10. Current and Power Values (measured)* Link State 3.3V Current (mA) 82562V Power Measurement (mW)** 100Mb - active 126 415.8 100Mb - idle 127 419.1 System State Maximum 100Mb - active 127 419.1 100Mb - idle 127 419.1 10Mb - active 95.5 315.5 10Mb - idle 66.5 219.4 No Link 95 311.8 D0 * Averaging of three typical units at typical and maximum conditions with nominal VCC. ** LED power deducted from overall power consumption. 8.2.1 X1 Clock DC Specifications Table 11. X1 Clock DC Specifications Symbol Parameter VIL Input Low Voltage VIH Input High Voltage IILIH Input Leakage Currents CI Input Capacitance Condition Min Typical Max Units 0.8 V 2.0 0 < VIN < VCC Notes V 10 A 8 pF 1 NOTES: 1. This characteristic is only characterized, not tested. It is valid for digital pins only. 30 Datasheet Networking Silicon -- 82562V 8.2.2 LAN Connect Interface DC Specifications Table 12. LAN Connect Interface DC Specifications Symbol Parameter Condition Min Typical Max Units VCCJ Input/Output Supply Voltage 3.0 3.45 V VIL Input Low Voltage -0.5 0.3VCCJ V VIH Input High Voltage 0.6VCCJ VCCJ + 0.5 V IIL Input Leakage Current 0 < VIN < VCCJ 10 A VOL Output Low Voltage IOUT = 1500 A 0.1VCCJ V VOH Output High Voltage IOUT = -500 A CIN Input Pin Capacitance 0.9VCCJ Notes V 8 pF 1 NOTES: 1. This characteristic is only characterized, not tested. It is valid for digital pins only. 8.2.3 LED DC Specifications Table 13. LED DC Specifications Symbol 8.2.4 Parameter Condition VOLLED Output Low Voltage IOUT = 10 mA VOHLED Output High Voltage IOUT = -10 mA Min Typical Max Units 0.7 V 2.4 Notes V 10BASE-T Voltage and Current DC Specifications Table 14. 10BASE-T Transmitter Symbol VOD10 Parameter Output Differential Peak Voltage Condition RL = 100 Min Typical 2.2 Max Units Notes 2.8 V 1 Units Notes K 1 NOTES:Current is measured between the transmit differential pins (TDP and TDN) at 3.3 V. 1. RL is the resistive load measured across the transmit differential pins, TDP and TDN. Table 15. 10BASE-T Receiver Symbol RID10 Datasheet Parameter Input Differential Resistance Condition DC Min 10 Typical Max 31 82562V -- Networking Silicon Table 15. 10BASE-T Receiver VIDA10 Input Differential Accept Peak Voltage 5 MHz f 10 MHz 585 VIDR10 Input Differential 5 MHz f 10 MHz Reject Peak Voltage VICM10 Input Common Mode Voltage 3100 mV 300 mV VCC/2 V NOTES: 1. The input differential resistance is measured across the receive differential pins, RDP and RDN. 8.2.5 100BASE-TX Voltage and Current DC Specifications Table 16. 100BASE-TX Transmitter Symbol VOD100 Parameter Output Differential Peak Voltage Condition RL = 100 Min Typical Max Units Notes 0.95 1.0 1.05 V 1 Units Notes K 1 NOTES:Current is measured between the transmit differential pins (TDP and TDN) at 3.3 V. 1. RL is the resistive load measured across the transmit differential pins, TDP and TDN. Table 17. 100BASE-TX Receiver Symbol Parameter RID100 Input Differential Resistance VIDA100 Input Differential Accept Peak Voltage VIDR100 Input Differential Reject Peak Voltage VICM100 Input Common Mode Voltage Condition DC Min Typical Max 10 500 1200 mV 100 mV VCC/2 V NOTES: 1. The input differential resistance is measured across the receive differential pins, RDP and RDN. 32 Datasheet Networking Silicon -- 82562V 8.3 AC Characteristics Figure 5 defines the conditions for timing measurements. The design must guarantee proper operation for voltage swings and slew rates that exceed the specified test conditions. Figure 5. AC Test Level Conditions Input Levels Output Levels VOH = 2.0 V 1.4 V VOL = 0.8 V 8.3.1 10BASE-T Normal Link Pulse (NLP) Timing Parameters Table 18. Normal Link Pulse Timing Parameters Symbol Parameter Condition T6 TNLP_WID NLP Width 10 Mbps T7 TNLP_PER NLP Period 10 Mbps Min Typical Max 100 8 16 Units Notes ns 24 ms Figure 6. Normal Link Pulse Timings T7 T6 Normal Link Pulse Datasheet 33 82562V -- Networking Silicon 8.3.2 Auto-Negotiation Fast Link Pulse (FLP) Timing Parameters Table 19. Fast Link Pulse Timing Parameters Symbol Parameter Condition Min Typical Max Units T8 TFLP_WID FLP Width (clock and data) T9 TFLP_CLK_CLK Clock Pulse to Clock Pulse Period 111 125 139 s T10 TFLP_CLK_DATA Clock Pulse to Data Pulse Period 55.5 62.5 69.5 s T11 TFLP_BUR_NUM Pulses in One Burst 17 33 # T12 TFLP_BUR_WID Burst Width T13 TFLP_BUR_PER FLP Burst Period 100 ns 2 8 16 Notes ms 24 ms Figure 7. Fast Link Pulse Timings T9 T10 T8 Fast Link Pulse Clock Pulse Data Pulse Clock Pulse T13 T12 FLP Bursts 34 Datasheet Networking Silicon -- 82562V 8.3.3 100BASE-TX Transmitter AC Specifications Table 20. 100BASE-TX Transmitter Timing Parameters Symbol T14 8.3.4 TJIT Parameter TDP/TDN Differential Output Peak Jitter Condition Min Typical Max Units 1400 ps Max Units Notes HLS Data Reset (JRSTSYNC) AC Specifications Table 21. Reset Timing Parameters Symbol Parameter Condition Min Typical T58 TRST_WID Reset Pulse Width 500 s T59 TPOP_RST Power-up to Falling Edge of Reset 1000 s Notes Figure 8. Reset Timing Parameters Power Up (Vcc) RESET Datasheet T59 T58 35 82562V -- Networking Silicon 9.0 Package and Pinout Information 9.1 Package Information The 82562V is a 81-pin Mold Cap package. The Package dimensions are shown in Figure 9. More information on Intel device packaging is available in the Intel Packaging Handbook, which is available from the Intel Literature Center or your local sales office. Figure 9. Dimension Diagram for the 82562V PLC $ % & 1.00 ' ( ) * + - 1.00 9.2 Pinout Information 9.2.1 82562V Pin Assignments Table 22. 82562V Pin Assignments 36 Pin Number Pin Name Pin Number Pin Name Pin Number Pin Name Pin Number Pin Name A1 NC C7 VSS F4 VSS J1 NC A2 NC C8 VSS F5 NC J2 NC A3 N3 C9 VSS F6 VSS J3 VSS A4 LINK_UP_N D1 JTXD0 F7 VCCA J4 NC A5 SPEED_LED D2 JRXD1 F8 NC J5 VSSA2 A6 adv10/ LAN_DIS/N D3 JRXD0 F9 NC J6 NC A7 NC D4 VCC G1 ISOL_TCK J7 NC A8 VSS D5 NC G2 ISOL_EXEC J8 NC A9 NC D6 VSS G3 TOUT J9 NC B1 NC D7 VCCR G4 VCCA2 B2 NC D8 RDN G5 NC Datasheet Networking Silicon -- 82562V Table 22. 82562V Pin Assignments Pin Number Pin Name Pin Number Pin Name Pin Number Pin Name B3 VCC D9 RDP G6 VSS B4 ACT_LED E1 VSSP G7 RBIAS100 B5 NC E2 JCLK G8 VSS B6 TEST_EN E3 JRST_SYNC G9 VSS B7 NC E4 VCC H1 ISOL_TI B8 TDP E5 VCC H2 NC B9 TDN E6 NC H3 VCC C1 JRXD2 E7 NC H4 NC C2 NC E8 VCCT H5 X2 C3 NC E9 VSS H6 X1 C4 VSS F1 JTXD2 H7 RBIAS10 C5 NC F2 VCCP H8 NC C6 VSSR F3 JTXD1 H9 NC Pin Number Pin Name 5*8(5+34 +0&&$3%*$/'0 ) ) ; ( ( s $%$//3$'&251(5 ' s ' s & & 6($7,1*3/$1( s % % s s < 7239,(: 6,'(9,(: $ $ 6,=( ; ':*180%(5 5(9 $ 6&$/( ' 6+((7 2) )250120%)/$0&':* Datasheet 37 82562V -- Networking Silicon 9.2.2 82562V Package Diagram Figure 10. 82562V Pin Out Diagram--Top View 38 NC NC NC NC VSSA2 NC VSS NC NC J NC NC RBIAS10 X1 X2 NC VCC NC ISOL_TI H VSSA VSS RBIAS100 VSS NC VCCA2 TOUT ISOL_EX ISOL_TC EC K G NC NC VCCA VSS NC VSS JTXD1 VCCP JTXD2 F VSS VCCT NC NC VCC VCC JRSTSYN C JCLK VSSP E RDP RDN VCCR VSS NC VCC JRXD0 JRXD1 JTXD0 D VSS VSS VSS VSSR NC VSS NC NC JRXD2 C TDN TDP NC TEST_EN NC ACT_LED VCC NC NC B NC VSS NC ADV10/la SPEED_L LINK_UP_ n_dis_n ED N NC NC NC A 9 8 7 3 2 1 6 5 4 Datasheet Networking Silicon -- 82562V Note: Datasheet This page intentionally left blank. 39 82562V -- Networking Silicon 40 Datasheet